Operator's

Manual

Super 7R

Edger

READ THIS BOOK

This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke

American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If you cannot read English, have this manual explained fully before attempting to operate this machine.

Si Ud. no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el manejo o servicio de esta máquina.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

For new books write to: Clarke ® , 2100 Highway 265, Springdale, Arkansas 72764.

Form No. 78155C 3/06 Printed in the U.S.A.

Contents of this Book

Operator's Manual - Section I

Operator Safety Instructions ......................................................... 3

Machine Specifications ................................................................ 5

Sanding Cuts and Sandpaper .................................................... 6

Machine Set-Up ........................................................................... 7

Operating Instructions ................................................................... 7

Adjustment Procedures ................................................................ 8

Routine Maintenance.................................................................... 8

Carbon Brushes...................................................................... 8

Dust Bag ................................................................................ 8

Bearings ................................................................................. 8

Parts and Service Manual - Section II

Maintenance .............................................................................. 10

Wiring Diagram .......................................................................... 11

Assembly Drawing ..................................................................... 12

Assembly Parts List ................................................................... 13

Page 2 Clarke ® American Sanders Super 7R Operator's Manual

WARNING

OPERATOR SAFETY INSTRUCTIONS

AVERTISSEMENT ADVERTENCIA

DANGER means:

WARNING means:

CAUTION means:

Severe bodily injury or death can occur to you or other personnel if the DAN-

GER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this

Owner's Manual and on your machine.

Injury can occur to you or to other personnel if the WARNING statements found on your machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all WARNING statements found in this Owner's

Manual and on your machine.

Damage can occur to the machine or to other property if the CAUTION statements found on your machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all CAUTION statements found in this Owner's

Manual and on your machine.

DANGER:

DANGER:

DANGER:

Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If you cannot read

English, have this manual explained fully before attempting to operate this machine.

Sanding/finishing wood floors can create an environment that can be explosive. The following safety procedures must be adhered to:

• Cigarette lighters, pilot lights and any other source of ignition can create an explosion when active during a sanding session. All sources of ignition should be extinguished or removed entirely if possible from the work area.

• Work areas that are poorly ventilated can create an explosive environment when certain combustible materials are in the atmosphere, i.e., solvents, thinners, alcohol, fuels, certain finishes, wood dust and other combustible materials. Floor sanding machines can cause flammable material and vapors to burn. Read the manufacturer's label on all chemicals used to determine combustibility. Keep the work area well ventilated.

• Spontaneous combustion or an explosion can occur when working with sanding dust.

The sanding dust can ignite and cause injury or damage. Sanding dust should be disposed of properly. Always empty the sanding dust into a metal container that is located outside of any building(s).

• Remove the contents of the dust bag when the bag is 1/3 full. Remove the contents of the dust bag each time you finish using the machine. Never leave a dust bag unattended with sanding dust in it.

• Do not empty the contents of the dust bag into a fire.

• Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer and punch to countersink all nails before sanding floors.

Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Keep all fasteners tight. Keep adjustments according to machine specifications.

Clarke ® American Sanders Super 7R Operator's Manual Page 3

DANGER:

DANGER:

DANGER:

DANGER:

DANGER:

Electrocution could occur if the machine is used on a power circuit that repeatedly trips or is undersized. Have a licensed electrician check the fuse, circuit breaker or power supply.

Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source. Disconnect the power supply before attempting any maintenance or service.

Electrocution could occur if machine is used on ungrounded electrical circuit. Never remove or disable the grounding supply conductor on the electrical cord. Consult an electrician if the grounding conductor is missing or if you suspect your circuit is not grounded properly.

Use of this machine with a damaged power cord could result in an electrical shock. Do not use the machine if the power cord is damaged. Do not use the electrical cord to move the machine.

Electrocution or injury could occur if the power cord is run over or damaged by the sander.

Keep the cord free from under the machine to avoid contact with the sandpaper. Always lift the power cord over the machine.

DANGER: Moving parts of this machine can cause serious injury and/or damage. Keep hands, feet and loose clothing away from all moving parts of the sander. Disconnect machine from the power source before changing the abrasive, emptying the dust bag, or performing any maintenance.

Do not operate unless all covers and guards are in place. Never leave machine unattended while motor is running or connected to power source.

WARNING: Failure to read and observe all safety statements found on your machine or in this Owner's

Manual can result in serious injury or damage. Read and observe all safety statements. Make sure that all labels, decals, warnings, cautions, and instructions are fastened to the machine.

Get new labels from your authorized Clarke American Sanders distributor.

WARNING: Sanding dust can be airborne and can be breathed in while operating a sander. Always wear a dust mask while operating sanding equipment.

WARNING: Injury to the eyes and/or body can occur if protective clothing and/or equipment is not worn while sanding. Always wear safety goggles, protective clothing, and a dust mask while performing any sanding operation.

WARNING: Bodily injury could occur if power is applied to the machine with the power switch already in the "ON" position. Always check to assure that the power switch is in the "OFF" position before applying power to the power cable.

WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities.

CAUTION: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs performed by unauthorized personnel will void your warranty.

Servicing of this unit must always be referred to an authorized American SandersTechnology distributor.

CAUTION:

CAUTION:

Use of this machine to climb on could result in injury or damage. Do not use this machine as a step or furniture.

Damage could occur to the machine if not properly kept in a dry building for storage. Store the machine in a dry building.

CAUTION:

CAUTION:

Page 4

Serious damage to the floor can occur if the machine is left running in one spot while the sanding disc is in contact with the floor. To avoid damage to the floor, do not dwell while lowering or raising the sanding disc. Always sand with a constant motion and pressure.

Do not rest machine on sanding disc. To do so may cause a flat spot and reduce the quality of performance. Tip machine back or rest on side when not in use.

Clarke ® American Sanders Super 7R Operator's Manual

Control Switch

Work Light

Model Super 7R

Specifications

Dust Collection Bag

Operating Handles

Wall Guard

Abrasive Wrench

Steel Reinforced

Molded Rubber

Sanding Pad

Specifications

Model

Electrical Rating

Storage Case

07011A 07075A 07054A 07098A

115V, 12.0 A, 60 Hz 115V, 12.0 A, 60 Hz 230V, 6.0A, 50 Hz 230V, 6.0 A, 50 Hz

Optional Standard Standard Standard

Motor

Abrasive Size

1hp 1hp 1hp 1hp

7" x 7/8" Dia. Disc 7" x 7/8" Dia. Disc 7" x 7/8" Dia. Disc 7" x 7/8" Dia. Disc

Disc Rate 2800 RPM

Disc Driver System Gear Driven

2800 RPM

Gear Driven

2800 RPM

Gear Driven

2800 RPM

Gear Driven

Power Cable

Dust Collection

14-3 Gray Rubber

Standard

Dust Control Rate 110 CFM

14-3 Gray Rubber

Standard

110 CFM

14-3 Gray Rubber

Standard

110 CFM

14-3 Gray Rubber

Standard

110 CFM

Clarke ® American Sanders Super 7R Operator's Manual Page 5

SANDING CUTS AND SANDPAPER

Initial Cut

The purpose of the initial cut is to remove old finish and gross imperfections on the floor surface. A coarse abrasive should be used.

If glazing, loading, or burning takes place immediately into an initial cut, select a coarser abrasive. If this should occur during an initial cut, the abrasive has dulled and must be replaced.

Final Cuts

The purpose of a finishing cut is to remove the scratches produced during the initial cut. Use a fine (60 - 80 grit) grain abrasive.

If the surface remains rough after a finishing cut, it may be necessary to use an even finer grain of abrasive (80

- 100 grit). Care should be taken in selecting the grit size of the abrasive. A very fine grain will close the pores on a wood floor making admission of a stain difficult.

Grain Use

12 grit For removing gross imperfections and

16 grit restore evenness to old flooring. To remove

20 grit build-up of paints and varnishes.

24 grit

30 grit For first sanding of new flooring (maple, oak).

36 grit For removing minor imperfections and finishes from old flooring.

40 grit For initial cut on new flooring (oak, walnut).

For removing minor imperfections and finishes from old flooring.

50 grit For first sanding of new flooring (cedar, pine,

fir) For clean-up of 16 grit.

60 grit For clean-up from initial cut 36 grit.

80 grit For final sanding of certain hardwoods. For clean-up of initial cuts (50 grit).

100 grit For final sanding of certain hardwoods and conifers where a smooth surface is desired.

120 grit For final sanding of certain conifers.

150 grit For final sanding of certain conifers where a smooth surface is desired for surface roughening between coats of finish.

7" Diameter 7" Diameter

Standard Grade

Part #/Qty

Professional Grade

Part #/Qty

945300/50

945301/50

945302/50

945594/200

945595/200

945596/200

945597/300

945305/100

945598/300

945599/300

945600/300

945307/100 945601/300

945308/100

945309/100

945602/300

945603/300

945310/100 945604/300

945605/500

945606/300

Page 6 Clarke ® American Sanders Super 7R Operator's Manual

MACHINE SET-UP

1. Familiarize yourself with the machine. Read all danger, warning, and caution statements and the Owner's Manual before operating this machine. If you or your operator cannot read English, have this manual explained fully before attempting to operate this machine.

2. Install dust bag support to the exhaust bracket (figure 1).

Place opening of dust bag over dust bag support and exhaust bracket; cinch and tie securely to exhaust bracket.

3. Remove screw and abrasive retainer. Center abrasive on pad and secure with abrasive retainer and screw. (Figure

2)

4. Return machine to upright position and tilt machine back on casters until it comes to rest on the exhaust bracket.

Machine will be in a reclined position. Do not allow machine to rest on pad especially after use, or compression set may take place within elastomer on pad. This will create a flat spot and bounce during use. (Figure 3)

OPERATING INSTRUCTIONS

1. Move machine to the location of your work. Set any exposed nails with hammer and punch to avoid encounter with abrasive.

WARNING: Bodily injury could occur if power is applied to the machine with the power switch already in the "ON" position. Always check to assure that the power switch is in the "OFF" position before applying power to the power cable.

2. Make sure the control switch is in the "Off" position then connect the supply cable to an appropriately grounded fused circuit. Connect the supply cable to the motor pigtail.

(Figure 4)

3. With the machine in the reclined position firmly grasp both handles and flip the control switch to the "ON" position.

(Figure 3.)

4.

Gradually lower pad to surface intended for sanding.

Make sure the machine is in motion while the pad is engaged with the surface to be sanded. You may use broad circular motion as you sand along the length of the surface or your may use a combination of forward and sideward motions. In time you will develop your own technique to optimize coverage and dust recovery. It is advisable to not add effort to the pad as this may lead to "nosing in" or "tipping" which produces grooves or lines on the surface.

5.

When replacing abrasive, emptying the contents of the dust bag, or sanding operation is completed, return machine to reclined position, flip control switch to "Off" then disconnect the motor pigtail from the supply cable.

6.

Empty dust bag whenever it becomes 1/3 full.

Clarke ® American Sanders Super 7R Operator's Manual

Figure 1

Figure 2

Figure 3

Figure 4

Page 7

OPERATING INSTRUCTIONS cont.

DANGER: Failure to disconnect the supply cable from machine whenever servicing, replacing abrasive, or emptying the dust bag could result in electrocution or severe injury. Never leave machine unattended while the supply cable is connected.

DANGER: Never leave dust bag unattended with sanding dust in it. Sanding dust can spontaneously ignite and cause a fire or explosion. Empty dust bag into a metal container, clear of any combus tibles. Do not empty content into a fire.

Do not overfill dust bag.

ADJUSTMENT PROCEDURES

Leveling

To level machine: Grasp caster adjusting screw "A" with an appropriate tool (pliers ect.). Using a similar tool, loosen locknut "B" with a counter clockwise motion. (Figure 5).

Condition - Pad creates ridges on both edges or a "hop" is experienced: Rotate both adjusting screws equal amounts clockwise. Tighten locknuts and test on a piece of plywood. Repeat procedure until condition is corrected. We recommend you not exceed 1/8" rotation for each attempt.

Condition - Pad creates a ridge on the tip of the pad:

Rotate both adjusting screws counter clockwise, tighten locknuts and test. Repeat procedure until condition is corrected. Use only 1/8 rotation for each attempt.

Condition - Pad creates a ridge on only one side of the pad:

Either rotate the adjusting screw of the side effected clockwise or rotate theadjusting screw opposite counterclockwise, depending on whether the ridge terminates beyond the tip of the pad or prior to it. If it is prior to the tip, adjust the side effected, otherwise adjust the opposite side.

ROUTINE MAINTENANCE

CAUTION: Failure to perform maintenance at recommended intervals may void warranty.

Carbon Brushes

Have the carbon brushes replaced at least every 500 hours and more frequently under heavy use.

Dust Bag

Periodically the dust bag should be turned inside out, shaken vigorously and machine washed in cold water to prevent pore blockage and loss of dust control.

Figure 5

A

B

Bearings

To insure reliable performance, have armature and pad driver bearings inspected for wear or damage after every 1500 hours. If used heavily, have the bearings replaced seasonally.

Lubrication

The machine comes fully lubricated. The gears in the gear box have enough lubrication for approximately six months of normal operation. Have the lubricant changed at least every 6 months or more frequently under heavy use.

Page 8 Clarke ® American Sanders Super 7R Operator's Manual

Super 7R

Edger

Section II

Parts and Service Manual

(78155C)

Clarke ® American Sanders Super 7R Operator's Manual Page 9

MAINTENANCE

CAUTION: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs performed by unauthorized personnel will void your warranty.

Failure to perform maintenance at recommended intervals may void warranty.

Carbon Brushes

Inspect all four brushes every 6 months or 250 hours.

Access to the brushes is gained through the front and back motor vent plugs and under both motor covers (figure

6). Press tab on spring clip assembly in, rotate, then remove (figure 7).Use needlenose pliers to disconnect the shunt wire. If any brush has worn to 3/8" in length or shorter, replace the entire set.

CAUTION: Use only motor brush PN 40818A or

PN 40055A with shunt wire or motor failure will occur.

When replacing the brushes make sure that the brush seats against the commutator, the spring rest in the recess of the brush, and the brush is free to travel. When returning the switch cover, keep any wires clear of the commutator and any pinch site.

To Change The Lubricant In The Gearbox

To change the lubricant in the gearbox, follow this procedure:

1. Put the machine upside down on a bench.

2. Align one of the two holes in the rubber pad with one of the three holes in the rotating wall guard.

3. Align both holes with one of the three screws in the gear housing cover. Remove the screw from the gear housing cover. (Figure 8)

4. Align the holes with each of the other two screws, then remove screws.

CAUTION: Make sure no dust enters the gear box.

Damage will occur to the gear box.

5. Remove the cover from the gear housing.

6. Remove the old lubricant from the gearbox.

7. Add six ounces of American SandersTechnology lubricant to the gear box.

CAUTION: To prevent damage to the motor, do not add more than six ounces of lubricant to the gearbox.

8. Using the three screws removed above, install the cover on the gear housing.

9. Start the machine and let it run for 15 minutes. A small amount of excess lubricant should flow out the vent hole. If none appears it may be necessary to add additional lubricant.

10. Wipe off excess lubricant and clear vent hole.

Page 10

Qty

1Qt.

Figure 6

Figure 7

Lubricants

1Gal.

Part No.

16610A

16611A

Figure 8

Clarke ® American Sanders Super 7R Operator's Manual

Model Super 7R Edger

Wiring Diagram 1/03

Clarke ® American Sanders Super 7R Operator's Manual Page 11

Super 7R Edger

Drawing - 3/06

99

9

8

16

38

39

11

18

47

10

17

15

19

52

20

7

1

14

3

5

12

4

37

2

14

6

34

36

51

29

46

48

49

50

95

35

7

31

32

21

22

23

24

25

26

28

30

33

27

29

90

78

91

92

93

73

74

75

76

77

82

96

97

98

79

80

81

83

84

85

94

53

56

41

40

54

58

59

41

63

33

60 47

61

69

62

64

65

66

67

68

87

65

70

65

71

65

72

75

100

57

Page 12 Clarke ® American Sanders Super 7R Operator's Manual

Super 7R Edger

Parts List - 3/06

Ref#

1

2

3

4

5

6

7

8

9

15

16

17

18

19

10

11

12

13

14

20

28

29

30

31

32

21

22

23

24

25

26

27

33

34

35

47

48

49

50

51

915028

980621

962550

36

37

302312

56475A

38 50932A

39 73285A

40 ‹ 80276A

41 ‹ 30613A

46 962211

980603

980643

42820A

42819A

962454

52

304208

20013A

298306

962545

85393A

962310

303602

46902A

911113

911116

10101B

10110A

303004

293403

306102

303002

307302

308202

297604

407302

902567

293514

316804

304204

Part No.

962404

70487A

646302

47394A

302310

302309

306802

43201A

40818A

40055A

962727

962988

980662

Description

Screw - #10-24 x 3 ¼ Ft. St. Mach.

Plate - Name

Plate - Dial

Switch - Toggle

Cover, Motor Brush R.H.

Cover, Motor Brush L.H.

Plug - Vent

Holder Assembly Brush

Carbon Brush 115V

Carbon Brush 240V

Screw - #8-32 x ½ Pan Head

Screw - ¼ -20 x 1¼ Pan St. Mach.

Washer - SH #1224-00 Lock

Qty

4

1

1

1

1

1

2

1

4

4

4

1

1

Screw - #6-32 x 3 /

8

Ft. St. Type 23

Screw - #10-24 x ¼ Pn. St. Mach.

Screw - #10-24 x ½ OV

Guard - Lamp

Socket -Assembly

Light Bulb 115V

Light Bulb 240V

Armature Assembly 115V

Armature Assembly 240V

Fan - Motor

Gasket - Fan Baffle

Plate - Exhaust Fan Baffle

Fan - Vacuum

Ring - Retaining

Spacer - Bearing

Seal - Oil

Ring - Retaining

Bearing

Pinion - Armature

Plug - Pipe 1 /

8

Housing - Gear

Key 1 /

8

x 5 /

8

Woodruff

Washer, #1108

Screw, 8-32 x 5 /

16

Cover, Motor

Strain Relief

Spring brush Holder

Label, Warning

Nut, Slip Joint

Washer, Seal

Screw - #10-24 x 2½ Pn. St. Mach.

Washer - #1110 Shakeproof

Washer - #10 7 /

16

Plain

Field 115 Volt

Field 240 Volt

Screw - ¼-20 x 1 Sc. Cap

Housing and Guard Assembly

Housing, Motor Super7R

Spring Load

7

2

1

1

2

1

1

1

4

1

1

2

2

3

1

1

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

4

1

1

1

1

1

NOTE: Asm. 12208A includes parts 64, 65, 70, 71, & 72.

NOTE: ‹ indicates a change has been made since the last publication of this manual.

NI = Not illustrated

Clarke ® American Sanders Super 7R Operator's Manual

92

93

94

95

84

85

87

90

91

79

80

81

82

83

74

75

76

77

78

69

70

71

72

73

64

65

66

67

68

59

60

61

62

63

Ref#

53

Part No.

42234A

42182A

40007A

54 ‹ 53544B

56 ‹ 61564A

57 ‹ 30563A

58 ‹ 21077A

293406

302101

962987

987300

962289

85702A

50740A

960130

920670

310803

298215

29404A

299704

925592

318303

307702

902550

303502

067304

302306

317204

293616

980088

13203A

980132

960140

925004

962109

34232A

87609A

84808A

962974

960125

41960A

41947A

96

97

98

99

100

NI

912169

45602A

911461

41708A

70175A

911248

45603A

40023A

12208A

31407A

Description

Cord Supply 115V

Cord Supply 240V

Cord Supply w/AUI-10P

Bag, Dust

Tube, Exhaust

Adapter, 2" Tube x 1½" Hose

Adapter, Exhaust

Gasket - Exhaust Bracket

Clamp - Wrench

Screw - 10-24 x 3 /

8

Pn. St. Typ.

Wrench

Screw - ¼-20 x 3 /

4

Soc. St. Cap

Screw - ¼-20 x 1¾

Bearing

Screw - Caster Adjusting

Nut - Lock Adjust

Bracket - Caster Support

Spacer - Collar

Yoke, Edger, Caster

Roller - Caster

Pin - ¼ x 1 Spirol

Spring - Load

Shaft - Drive Gear

Bearing

Gear - Drive

Ring - Retaining

Cover - Assembly Gear Housing

Retainer - Disc Guard

Guard - Disc

Washer

Assembly - Sanding Pad

Washer - Disc, Retaining

Screw - Paper Lock

Pin - Cotter 1 /

16

x ½

Screw - #10-24 x 5 /

8

Pn SS

Gasket - Gear Case Cover

Washer Seal

Screw, 10-24 x 3 /

4

Screw, 6-32 x ½

Assembly Screw Lock

Motor Pigtail 115V

Motor Pigtail 240V

Plug L5-15P (115V)

Plug L6-15P (240V)

Connector L5-15R (115V)

Connector L6-15R (240V)

Tag, Warning

Plug 5-15P (115V)

Plug 6-15P (240V)

Plug AUI-10P

Caster, Assembly

Case, Super 7R Edger

1

1

4

4

3

1

1

2

1

1

1

2

1

1

1

2

2

2

2

1

2

8

2

2

2

1

1

1

1

4

Qty

1

1

1

1

1

1

1

1

1

1

1

1

3

4

1

1

1

1

1

1

1

1 i f g h a b c d e

Accesories Available

312404

311306

312904

315604

317004

317304

762005

920208

962013

962233

Cutter Disc Assembly

Blade - Disc Cutter

Eject Disc Cutter

Mallet

Punch Center

Ring Disc Cutter

Clamp

Nut - ¼-20 Hex

Screw ¼-20 x 1¼ R

Screw ¼-20 x 5 /

16

S

Page 13

1

1

1

1

1

1

1

1

1

1

NOTES

Page 14 Clarke ® American Sanders Super 7R Operator's Manual

U. S. A. Locations

CLARKE PRODUCT SUPPORT BRANCHES

European Locations

CORPO

PRODUCTION FACILITIES

Clarke ® , Springdale, Arkansas

2100 Highway 265

Springdale, Arkansas 72764

(479) 750-1000

Customer Service - 1-800-253-0367

Technical Service - 1-800-356-7274

American Lincoln ® , Bowling Green, Ohio 43402

1100 Haskins Road

PRODUCTION FACILITIES

ALTO Danmark A/S, Aalborg

Blytaekkervej 2

DK-9000 Aalborg

+45 72 18 21 00

ALTO Danmark A/S, Hadsund

Industrikvarteret

DK-9560 Hadsund

+45 72 18 21 00

SERVICE FACILITIES

Clarke ® , Elk Grove, Illinois 60007

2280 Elmhurst Road

(847) 956-7900

Clarke ® , Denver, Colorado 80204

1955 West 13th Ave.

(303) 623-4367

Clarke ® , Houston, Texas 77040

7215 North Gessner Road

713-937-7717

SERVICE AND SALES FACILITY

American Lincoln ® / Clarke, Madison Heights,

Michigan 48071-0158

29815 John R.

(810) 544-6300

American Lincoln ® / Clarke, Marietta, Georgia 30066

1455 Canton Road

(770) 973-5225

Clarke ®

Clarke American Sanders

A.L. Cook

Customer Service Headquarters and Factory

2100 Highway 265

Springdale, Arkansas 72764

(479) 750-1000

Technical Service

1-800-356-7274

Clarke ® American Sanders Super 7R Operator's Manual

SALES SUBSIDIARIES

ALTO US - Canada, Ontario (Canada)

4080 B Sladeview Crescent Unit 1

Mississauga, Ontario L5L 5Y5

(905) 569 0266

ALTO Overseas Inc., Sydney (Australia)

1B/8 Resolution Drive

Caringbah NSW 2229

+61 2 9524 6122

ALTO Cleaning Systems Asia Pte Ltd., Singapore

No. 17 Link Road

Singapore 619034

+65 268 1006

ALTO Deutschland GmbH, Bellenberg (Germany)

Guido-Oberdorfer-Straße 2-8

89287 Bellenberg

+49 0180 5 37 37 37

ALTO Cleaning Systems (UK) Ltd., Penrith

Gilwilly Industrial Estate

Penrith

Cumbria CA11 9BN

+44 1768 868 995

ALTO France S.A. Strasbourg

B.P. 44, 4 Place d’Ostwald

F-67036 Strasbourg

Cedex 2

+33 3 8828 8400

ALTO Nederland B.V.

Postbus 65

3370 AB Hardinxveld-Giessendam

The Netherlands

+31 184 677 200

ALTO Sverige AB, Molndal (Sweden)

Aminogatan 18

Box 4029

S-431 04 Molndal

+46 31 706 73 00

ALTO Norge A/S, Oslo (Norway)

Bjornerudveien 24

N-1266

+47 2275 1770

Page 15

Clarke

®

American Sanders U. S. Warranty

This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke American Sanders's Maintenance and Operations

Instructions.

This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear parts such as electrical cable or V-belts.

If difficulty develops with the product, you should:

(a). Contact the nearest authorized Clarke American Sanders repair location or contact the Clarke American

Sanders Service Operations Department, 2100 Highway 265, Springdale, Arkansas 72764, for the nearest authorized Clarke American Sanders repair location. Only these locations are authorized to make repairs to the product under this warranty.

(b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to and from the repair location must be prepaid by the purchaser.

(c). Clarke American Sanders will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.

Clarke American Sanders's liability under this warranty is limited to repair of the product and/or replacement of parts and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSEQUEN-

TIAL DAMAGES.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE ARE NO

WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. NO WARRANTIES,

INCLUDING BUT NOT LIMITED TO WARRANTY OF MECHANTABILITY, SHALL BE IMPLIED. A warranty registration card is provided with your Clarke American Sanders product. Return the card to assist Clarke

American Sanders in providing the performance you expect from your new floor machine.

Clarke ® , 2100 Highway 265, Springdale, Arkansas 72764

Clarke American Sanders reserves the right to make changes or improvements to its machine without notice.

Always use genuine Clarke American Sanders Parts for repair.

2100 Highway 265

Springdale, Arkansas, 72764