advertisement
Owner's Manual
®
6.5 HORSEPOWER
22" REAR DmSCHARGE
POWER PROPELLED
ROTARY LAWN MOWER
Model No.
917.377561
o Safety
Assembly o Operation o Maintenance
,, EspaSol o Repair Parts
CAUTION:
Read and follow all
Safety Rules and Instructions before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Warranty
Safety Rules
Assembly
Operation
Maintenance Schedule
Maintenance
Product Specifications
Service and Adjustments
4 Storage
6 Troubleshooting
10 Repair Parts
10 Parts Ordering
11
13
14
15
32
Back Cover
LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workmanship.
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase°
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plugo o Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States. This warranty applies only while this product is in use in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179
TRAINING:
• Read this operator's manual carefully,
Become familiar with the controlsand know how to operate your mower
properly. Learn how to quickly stop mower.
° Do not allow children to use your mower_
Never allow adults to use mower without proper instructions.
• Keep the area of operation clear of all persons, especially small children and pets.
o Use mower only as the manufacturer intended and as described in this manual
° Do not operate mower if it has been dropped or damaged in any manner.
Always have damage repaired before using your mower.
o Do not use accessory attachments that are not recommended by the manufacturero Use of such attachments may be hazardous.
• The blade turns when the engine is running.
PREPARATION:
° Always thoroughly check the area to be mowed and clear it of all stones, sticks, wires, bones, and other foreign objects.
These objects will be thrown by the blade and can cause severe injury. o Always wear safety glasses or eye shields when starting and while using your mower.
° Dress properly. Do not operate mower when barefoot or wearing open sandals_
Wear only solid shoes with good traction when mowing.
= Check fuel tank before starting engine.
Do not fill gas tank indoors, when the engine is running or when the engine is
hot.Allowthe engineto coolfor several minutesbefore_'illingthe gastank.Clean
off any spilledgasolinebeforestartingthe engine.
- Alwaysmakewheelheight adjustments beforestartingyourmower.Never
attemptto do thiswhile the engineis running, o Mow onlyin daylightor good artificial light,
OPERATION:
• Keep your eyes and mind on your mower and the area being cut. Do not let other interests distract you.
° Do not mow wet or slippery grass. Never run while operating your mower. Always
be sure of your footing -- keep a firm hold on the handles and walk.
° Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times_
° Always stop the engine whenever you leave or are not using your mower, or before crossing driveways, walks, roads, and any gravel--covered areas.
• Never direct discharge of material toward bystanders nor allow anyone near the mower while you are operating it.
° Before cleaning, inspecting, or repairing your mower, stop the engine and make absolutely sure the blade and all moving parts have stoppe& Then disconnect the spark plug wire and keep it away from the spark plug to prevent accidental starting.
• Do not continue to run your mower if you hit a foreign object. Follow the procedure outlined above, then repair any damage before restarting and operating you mower.
• Do not change the governor settings or overspeed the engine. Engine damage or personal injury may result.
• Do not operate your mower if it vibrates abnormally. Excessive vibration is an indication of damage; stop the engine, safely check for the cause of vibration and repair as required.
o Do not run the engine indoors. Exhaust fumes are dangerous.
° Never cut grass by pulling the mower towards you_ Mow across the face of slopes, never up and down or you might lose your footing. Do not mow excessively steep slopes. Use caution when operating the mower on uneven terrain or when changing directions -- maintain good footing°
° Never operate your mower without proper guards, plates, grass catcher or other safety devices in place.
MAINTENANCE AND STORAGE: o Check the blade and the engine mounting bolts often to be sure they are tightened properly.
o Check all bolts, nuts and screws at frequent intervals for proper tightness to be sure mower is in safe working condition.
° Keep all safety devices in place and working.
o To reduce fire hazard, keep the engine free of grass, leaves or excessive grease and oil.
o Check grass catcher often for deterioration and wear and replace wom bags.
Use only replacement bags that are recommended by and comply with specifications of the manufacturer of your mower.
• Always keep a sharp blade on your mower.
o Allow engine to cool before storing in any enclosure_ o Never store mower with fuel in the tank inside a building where fumes may reach an open flame or an ignition source such as a hot water heater, space heater, clothes dryer, etc.
CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.
WARNING
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Theseaccessories
lawn mower was produced. They are also available at most Sears retail outlets and service centers° Most Sears stores can also order repair parts for you, when you provide the model number of your lawn mower. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
=, ,, ,,,, ,, == = ,,HLL
CLIPPING DEFLECTOR
FOR REAR DISCHARGE LAWN MOWERS ....
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
LAWN MOWER MAINTENANCE
MULCHER KITS
FOR
SIDE DISCHARGE
STABILIZER
GAS CANS
.....................
.........
AIR FILTERS SPARK PLUGS
BELTS BLADES BLADE ADAPTERS WHEELS ENGINE OIL
Read these instructionsand this manual in its entirety before you attempt to assemble or operate your new lawn mower. Your new lawn mower has been assembfed at the factory with the exception of those parts left unassembled for shipping purposes. PJ1parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag.
To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.
TO REMOVE LAWN MOWER FROM
CARTON o Remove loose parts included with mower.
o Cut down two end comers of carton and lay end panel down flat.
o Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle.
• Roll lawn mower out of carton and check carton thoroughly for additional looseparts.
HOW TO SET UP YOUR LAWN
MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handles carefullyso as
not to pinch or damage controlcables. o Raise handles untillower handle section
locksintoplace in mowing position.
° Remove protectivepadding, raise upper
handlesection intoplace on lower handle and tightenboth handleknobs.
° Remove handle padding holdingoperator presence controlbar to upper handle.
- Your lawn mower handle can be adjusted for your mowing comfort. Refer to "Adjust
Handle" inthe Service and Adjustment section ofthis manual
NOTE: Forshipping purposes,the rear wheels on your lawn mower are not adjusted to the same positionas the front wheels. Beforeoperatingmower adjust all wheels to the same cutting height position°
Operator presence contrql bar
Uppper handle -....
//_
Lift up -"
,_._
Lift up/_ ;,Y
TO INSTALL ATTACHMENTS
Your fawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging:
• Open rear door and remove mulcher plug.
Store mulcher plug in a safe place.
o You can now install catcher or optional clipping deflector.
° To return to mulching operation, install mulcher plug into discharge opening of mower. Be sure all tabs are seated properly.
__'X'_/7 M°w!ng
Lower ha_
Mulcher plug ---'_
CAUTION: Do not run your lawn mower without mulcher plug in place or approved clipping deflector or grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open.
5
READTHIS OWNER'SMANUALANDSAFETYRULESBEFOREOPERATINGYOUR
LAWNMOWER. Comparethe illustrationswith your lawn mowerto familiarizeyourself withthe locationof variouscontrolsand adjustments.Savethis manualfor future reference.
.............
JLI L _.
_ EL = : _ 911rpr =
CAUTION
OR WARNING
ENGINE
ON
ENGINE
OFF
Engine zone control cable
FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
AND FEET AWAY presence control bar
Dr_ve control lever
Srarter handle
Handle knob
Grass
Mulcher plug
Engine oil cap w/dipstick
Housing cover
Gasoline cap c
Wheel adjuster
(on each wheel)
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the American
National Standards Institute and the U.S. Consumer Product Safety Commission. The blade turns when the engine is running.
Operator presence control bar - must be held down to the handle to start the engine.
Release to stopthe engine.
Primer- pumps additional fuel from the
carburetorto the cylinder for use when starting a cold engine.
Starter handle - used for starting the engine.
Drive control lever- used to engage power-
propelledforward motion of lawn mower.
Mulcher plug - must be removed to convert to bagging or discharging 9peration.
6
The operation'ofany lawn mowercan result in foreignobjectsthrowninto the eyes, which can resultin severeeye damage. Alwayswearsafetyglassesor eye shieldswhileoperatingyour lawn moweror performingany adjustmentsor repairs. We recommenda wide vision safety mask overthe spectaclesor standardsafetyglasses.
HOW TO USE YOUR LAWN MOWER
CAUTION: Do not run your lawn mower without mulcher plate in place and door closed or without an approved clipping deflector or grasscatcher in place.
Never attempt to operate the lawn mower with the rear door removed or propped open.
ENGINE SPEED
The engine speed was set at the factory for optimum performance.
Speed is not adjustable.
ENGINE ZONE CONTROL
CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.
° Your lawn mower is equipped with an operator presence control bar which requires the operator to be posi'r_oned behind the lawn mower handle to start and operate the lawn mower.
TO ADJUST CUTtiNG HEIGHT
° Raise wheels for low cut and Iowerwheels for high cut.
• Adjust cutting height to suit your requirements. Medium position is best for most lawns.
° To change cutting height, squeeze adjuster lever toward wheel. Move wheel up or down to suit your requirements, Be sure atl wheels are in the same setting.
NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs.
_ _ Lever
Raise Wheels for Low Cut
TO ATTACH GRASS CATCHER
o Close the flip lid. Flip lid must be dosed while operating lawn mower.
• Lift the rear door on the mower housing and place the grass catcher frame onto the formed tabs on the rear door hinge bracket.
o The grass catcher is secured to the lawn mower housing when the rear door is lowered onto the grass catcher frame,
CAUTION: Do not run your lawn mower without clipping deflector or approved grass catcher in place.
Never attempt to operate the lawn mower with the rear door removed or propped open.
Hinge brack_
Plate Tab
Rear door
Formed tabs
TO EMPTY GRASS CATCHER
o To remove grass catcher, release operator presence control bar to stop engine.
- Lift up rear door and remove the grass catcher by the handle.
° Do not drag the bag when emptying; itwill cause unnecessary wear.
DRIVE CONTROL o Self-propelling is controlled by holding the operator presence control bar down to the handle and pushing the drive control lever forward until it clicks; then release the lever.
° Forward motion wilt stop when the operator presence control bar is released.
To stop forward motion without stopping engine, release the operator presence control bar slightly until the drive control disengages.
Hold operator presence control bar down to handle to continue mowing without selfpropelling.
o To keep drive control engaged when turning corners, push down on handle and lift front wheels off ground while turning lawn mower.
Operator presence control bar
\ Ddve
To engage drive control
Drive control desengaged
BEFORE STARTING ENGINE
OIL
Your lawn mower is shipped without oil in the engine_
- Be sure mower is level and area around oil fill is clean.
, Remove engine oil cap w/dipstick and fill to the full line on the dipstick.
o Use 20 ozsoof oil. For type and grade of oil to use, see "ENGINE" in Customer
Responsibilities section of this manual.
° Pour oil slowly. Do not overfill.
° Check oil level before each use. Add oil if needed. Fill to full line on dipstick.
• To read proper level, lighten engine oil cap each time.
o Reinstall engine oil cap and tighten_
° Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirty conditions.
ADD GASOLINE o RII fuel tank. Use fresh, dean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.
IMPORTANT: When operating in temperatures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.
WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids dudng storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or Iongero
Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See
Storage Instructions for additional information.
Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.
CAUTION: F]II to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled
oil or fuel. Do not store, spill or use gasoline near an open flarne.
Gasoline filler cap Entine oil cap w/ dipstick
TO START ENGINE
o To start a cold engine, push primer five (5) times before trying to start. Use a firm push,
This step is not usually necessary when starting an engine which has already run for
a few minutes.
° Hold operatorpresence control bar down to the handle and pull starter handle quickly.
Do not allow starter rope to snap back.
° To stop engine, release operator presence control bar.
NOTE: Incooler weather it may be necessaryto repeatpriming steps° In warmer weather over primingmay cause floodingand enginewilt not start. If you do flood engine,wait a few minutesbefore attemptingto startand do not repeat primingsteps.
MOWING TIPS o Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings.
o For extremely heavy cutting, reduce the width of cut and raise the rear of the lawn mower housing one (1) wheel adjuster setting higher than the front for better discharge of grass.
• For better grass bagging and most cutting conditions, the engine speed should be set in the fast position.
° When using a rear discharge lawn mower in moist, heavy grass, clumps of cut grass may not enter the grass catcher° Reduce ground speed (pushing speed) and/or run the lawn mower over the area a second time.
. If a trail of grass clippings is left on the right side of a rear discharge lawn mower, mow in a clockwise direction with a small overlap to collect the clippings on the next pass,
• Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life.
o Pores in cloth grass catchers can become filled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catchers off with water and let dry before using.
Max t/3
MULCHING MOWING TIPS
IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. See "Cleaning" in CUSTOMER
RESPONSIBILITIES section of this manual, o The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quicldy to provide nutrients for the lawn_ Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades.
o Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action, The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun.
o For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades.
If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly.
• Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path,
• Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn.
Clean/Inspect Grass Catcher
(If Equipped) .......
M Clean Lawn Mower
O i Clean Under Drive Cover
(Power-Propelled Mowers)
IN Check drive belt/pulleys
_
E i (Power.Propelled Mowers)
Check/Sharpen/Replace Blade
LubricationChart
..................
Clean Battery/Recharge
±
(Electric Start Mowers}
,,
E ICheck Eng!ne Oil Level
N Change Eng!ne Oil
G I clean Air Filter
...........
I Inspect Muffler ....
N' clean or Replace Spark Plug i:
E Replace Air Filter Paper Cartridge
_
,,,I
......
, v' v'
v'
v' v'
, ,, _
_2
......
v' v' v'4
=
!
1 - Change more often when operating under a heavy toad or in high ambient tempuretures
2 - Service more often when operaUng in dirty or dusty condi_ons
3 - Replace blades more often when mew_ng in sandy soif
4 - Charge 48 hours at end of season,
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not
cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must
maintain mower as instructed in this manual.
Some adjustments wilt need to be made periodically to properly maintain your unite
All adjustments in the Service and
Adjustments section of this manual should be checked at least once each season.
o Once a year, replace the spark plug, replace air filter element and check blade for wear.
A new spark plug and clean/new air filter element assures proper air-fuel mixture and helps your engine run better and last longer.
° Follow the maintenance schedule in this manual.
BEFORE EACH USE o Check engine oil level
• Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRICA-
TION CHART"),
LUBRiCATiON
(_) Wheel adjuster
CHART
(_) Engine oil
Brake spring bracket
(_ Handle bracket mounting pin
(_ Rear door hinge
(_ Spray lubricant
(_) Referto CUSTOMER RESPONSIBILITIES
"ENGINE" section.
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self lubricating beatings. If you feel they must be lubricated.,use only a dry, powdered graphite type lubricant sparingly.
10
PRODUCT SPECiFiCATiONS
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
HORSEPOWER:
DISPLACEMENT:
._ASOLINE CAPACITY/TYPE:
OIL TYPE (API-SF/SG/SH):
9t 7.377561
6.5
12.56 CU. IN_
1.25 QUARTS
UNLEADED REGULAR
SAE 30 (ABOVE 32°F)
SAE 5W-30 (BELOW 32°F)
;PARK PLUGiGAPi:_:*.030,) ...... ., .... ,..::.::
VALVECLEARANCE:
EXHAUST: .004 - .008
SOLID STATE IGNITION
AIR GAP: .0125 IN.
BLADE BOLT TORQUE : -._".
_ 35-40 FT. LBS.
The model and serial numbers will be f0_bd on:_adecal attached to the rear of the lawn mower housing.Record
both. serial;:_Umbe:r and date of purchase in space provided above.
:i_i_: _i
LAWN MOWER
Always observe safety rules when performing any maintenance,
TIRES
""_
o Remove blade and attaching hardware
(bolt, lock washer and hardened washer).
NOTE: Remove the blade adapter and check the key inside hub of blade adapter.
- Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber_
The key must be in good condition to work properly.
Replace adapter if damaged.
o Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause TO REPLACE BLADE tire damage.
BLADE CARE
For best results, mower blade must be kept sharp. Replace bent or damaged blades.
TO REMOVE BLADE o Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug.
• Turn lawn mower on its side° Make sure air
• Position the blade adapter on the engine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.
° Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.
° Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine_
, Install the blade bolt with the lock washer filter and carburetor are up.
° Use a wood block between blade and and hardened washer into blade adapter and crankshafL
° Use block of wood between blade and lawn mower housing to prevent blade from tuming when removing blade bolt.
° Protect your hands with gloves and/or wrap blade with heavy cloth.
,, Remove blade bolt by turning counterclockwise. Use a 9/I 6" box or open-end wrench.
mower housing and tighten the blade bolt, turning clockwise.
o The recommended tightening torque is 35-
40 ft. lbso
IMPORTANT: Blade bolt is grade 8 heat treated.
11
NOTE: We do not recommendsharpeningblade - but if you do, be sure the blade is balanced.
TO SHARPENBLADE
Care should be takento keepthe blade balanced. An unbalancedbladewill cause eventualdamage to lawn mower or
engine.
o The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.
• To check blade balance, drive a nail into a beam or wall. Leave about one inch of the straight nail exposed. Place center hole of blade over the head of the nail. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.
Blade Crank shaft keyway
Key
Blade
• Remove any trash or gr,ass cuttings from inside the dust cover, pinion and!or drive wheel gear teeth.
• Put wheels back in place.
° If after cleaning, the drive wheels do not turn freely, contact your nearest authorized service center.
GEAR CASE o To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up.
Clean under the drive cover twice a season.
• The gear case is filled with lubricant to the proper level at the factory.
The only time the lubricant needs attention is if service has been performed on the gear case_
• tf lubricant is required, use only Texaco
Starplex Premium I Grease, Part No.
750355.
Do not substitute.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with
API service classification SF,SG, or SH.
Select the oil's SAE viscosity grade according to your expected operating temperature.
bolt
Lock washer Hardened edge washer
GRASS CATCHER
Blade adapter
Crank shaft o The grass catcher may be hosed with water, but must be dry when used.
° Check your grass catcher often for damage or deterioration. Through normal use it will wear. If catcher needs replacing, replace only with a manufacturer approved replacement catcher. Give the lawn mower model number when ordering.
DRIVE WHEELS
Check front drive wheels each time before you mow to be sure they move freely.
The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.
If necessary to clean the drive wheels, check both front wheels.
° Remove hubcaps, hairpin cotters and washers.
• Remove wheels from wheel adjusters°
[-- J i
L'mm= m!
i ........
[
I'_ ,'_ . o* , 3o. _.,_, r.o.
_,
,, O" '_ ,,,-'tO* 30",,,,,,,, 4_
RANGE ANTICIPATED BEFORE NEXT OiL CHANGE _, _MPERATURE
NOTE: Although mu_-viscos'rty oils
(5W30, 10W30 etc.) improve starting in cold weather, these multi-vi_x_sity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.
Change after the first 25 hours of operation at
least once a year if the lawn mower is not used for 25 hours in one year.
Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. _ghten oil plug securely each time you check the oil level,
12
TOCHANGEENGINEOIL
NOTE_Before'tippinglawn mowerto drain oil, drainfuel tank by runningengine untilfuel tank is empty° andplacewirewhereit cannotcomein contactwithsparkplug.
o Removeengineoilcap;layasideona clean surface.
, Tiplawnmoweronitssideasshownand drainoilintoa suitablecontainer.Rocklawn
mowerbackandforthto removeanyoil trappedinsideofengine.
o Wipeoffanyspilledoilonlawnmowerand onsideofengine.
o Fillenginewithoil. Fillonlytothe "FULL" lineonthedipstick.DONOTovert'ilL
° Replaceengineoi!cap.
AIR FILTER
Container
Your engine will not run properly and may be damaged by using a dirty air filter.
Replace the air filter ever,./year, more often if you mow in very dusty, dirty conditions.
Do not wash air filter.
TO CHANGE AIR FILTER
° Remove the air filter by turning clockwise to the stop and pull away from collar,
° Remove filter from inside of cover.
• Clean the inside of the cover and the collar to remove any dirt accumulation.
. Insert new filter into cover.
• Put air filter cover and filter into collar aligning the tab with the slot,
• Push in on cover and turn counterclockwise to tighten.
Collar
Tum
Cbckwise to
\
Remove
CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge° Do not oil cartridge. Do not use pressurized air to clean or dry cartridge.
MUFFLER
Inspect and replace corroded muffler as it could create a fire hazard and!or damage,
SPARK PLUG
Change your spark plug each year to make your engine start easier and run better, Set spark plug gap at .030 inch,
CLEANING
IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean the underside of your mower after each use°
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with the spark plug.
• Turn lawn mower on its side, Make sure air filter and carburetor are up, Clean the underside of your lawn mower by scraping to remove build-up of grass and trash.
° Clean engine often to keep trash from accumulating, A clogged engine runs hotter and shortens engine life.
o Keep finished surfaces and wheels free of all gasoline, oil,etc, o We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out,
Water in engine can result in shortened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a season, Scrape underside of cover with put[y knife or similar tool to remove any build-up of trash or grass on underside of drive cover.
Slot
/
Air Filter
Clip
Tab
Air Filter
Cover mum
Counter°
Clockwise to
Tighten
13
CAUTION: BEFORE PERFORMING
ANY SERVICE OR ADJUSTMENTS: o Release control bar°
° Make sure the blade and all moving parts have completely stopped°
• Disconnect spark plug wire from spark plug and place where it cannot come in contact with plugo
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in the
Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear
wheels of your lawn mower, isprovided to minimize the possibility that objects will be thrown out the rear of the lawn mower into the operator's mowing position. If the rear deflector becomes damaged, it should be replaced_
TO REMOVE/REPLACE DRIVE BELT o Remove drive cover. Remove belt by
pushingdown on gear case pulley and roll belt off,
° Turn lawn mower on its side with carburetor and fuel cap up.
o Remove blade.
o Remove debris shield_
° Remove belt from engine pulley on crankshaft,
• Install new belt by reversing above steps, o Always use factory approved belt to assure fit and long life.
Drive cover
° Remove the starter rope guide from the lower handle,
° Remove hairpin cotters.
° Disconnect the lower handle from the handle brackets, o Turn the handle over and reassemble the hairpin cotters that have been removed° o Reassemble the starter rope guide,
= Reassemble the controls and the operator presence control bar to the upper handle.
CAUTION: The operator presence control bar must pivot freely to permit blade brake engagement when control bar is released.
Do not over lighten the fasteners holding the controls to the upper handle.
= To change from medium low to high position only the upper handle section will have to be turned over.
° To change from medium low to low position, onty the lower handle section will have to be tumed over.
Shipping position
Medium low high
_.
Low
Belt
Push down
TO ADJUST HANDLE
Your lawn mower handle can be raised or lowered foryour mowing comfort, Four (4) positions are available: high, medium high, medium low and low. Handles are shipped mounted in the medium low position.
o To change from medium low to medium high position, the upper and lower handle sections will have to be turned over° o Remove cable dip& o Remove the controls and operator presence contrr_lbar f:om the upper handle.
Squeeze to remove
Hairpin clip
Lower handle
Handle bracket
14
Immediately prepare you[!_n
mower for storage at the end of th_son or if the unit will not be used for 30 day_r more.
LAWN MOWER
When lawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.
• Clean entire lawn mower (See "CLEANING" in the Customer Responsibilities section of this manual)° o Lubricate as shown in the Customer
Responsibilities section of this manual.
• Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear.
Replace if necessary.
° Touch up all rusted or chipped paint surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for storage.
o Squeeze the bottom ends of the lower handle toward each other until the lower handle clears the handle bracket, then move handle forward.
° Loosen upper handle mounting bolts enough to allow upper handle to be folded back.
IMPORTANT: When folding the handle for storage or transportation, be sure to fold the handle as shown or you amy damage the control cables.
• When setting up your handle from the storage position, the lower handle wit!
automatically lock into the mowing position.
Lower handle
Squeeze to fold
Handle bracket
Operator presence control bar
Upper
.i handle
Fold reward for storage
/_
_._
Lower handle
Mowing position
ENGINE
FUEL SYSTEM
IMPORTANT.' It is importantto prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel system parts such as carburetor, fuel filter, fuel hose or tank during storage. Also, experience indicates that alcohol blended fuels ( called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage° Acidic gas can damage the fue! system of an engine while in storage.
• Drain the fuel tank.
° Start the engine and let it run until the fue!
lines and carburetor are empty.
° Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.
° Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable altemative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor.
Do not drain the gas tank and carburetor if using fuel stabilizer.
Hairpin cotter
15
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the
Customer Responsibilities section of this manual).
CYLINDER
• Remove spark plug_ o Pour one ounce (29 ml) of oil through spark plug hole into cylinder, o Pull starter handle slowly a few times to distribute oil.
• Replace with new spark plug.
OTHER
• Do not store gasoline from one season to another°
= Replace your gasoline can if yourcan starts to rust, Rust and/or dirt in your gasoline will cause problems° o If possible, store your unit indoors and cover it to give protection from dust and dirt, o Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic, Plastic cannot breathe which allows condensation to form and will cause your unit to rust,
IMPORTANT: Never cover mower while engine and exhaust areas are still warm,
CAUTION: Never store the lawn mower with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure,
TROUBLESHOOTING
PROBLEM
............
Does not start ill,,, o o
CHART
, ,,,,, ,,
CAUSE
...........
• Dirty air filter°
° Out of fuel,
Stale fuel.
Water in fuel.
* Spark plug wire is disconnected.
° Bad spark plug.
o Loose blade or broken blade adapter.
o Control bar in released position.
o Control bar defective.
CORRECTION o w o
Clean/replace air filter.
Fill fuel tank,
Drain tank and refill with fresh clean fueL
Drain fuel tank and carburetor and refill tank with fresh gasoline.
Connect wire to plug,
@ Replace spark plugo
° "lighten blade bolt or replace blade adapter, o Depress control bar to handle,
° Replace control bar,
, ,,,,, ,,
16
TROUBLESHOOTING
PROBLEM ss of power
CHART
OAUSE
' Rear of lawn mower housing or cutting blade dragging in heavy grass.
o Cutting too much grass.
o Dirty air filter.
° Buildup of grass, leaves, and trash under mower° o Too much oil in engine.
° WalkJngspeed too fast.
orcut-uneven cessive bration to t_erropehard
_uli ass catcher t filling (if so uipped)
Lrd to push
° Worn, bent or loose blade.
- Wheel heights uneven.
• Low engine speed.
= Buildup of grass, leaves and trash under mower.
o Worn, bent or loose blade.
° Bent engine crankshaft.
o Engine flywheel brake is on
when control bar is released.
° Bent engine crankshaft.
o Blade adapter broken.
, Blade dragging in grass.
° Cutting height too low.
° Uft on blade worn off.
° Catcher not ventingair°
° Low engine speed.
• Grass istoo high or wheel height is too low.
• Rear of lawn mower housing or blade dragging in grass.
o Grass catcher too full.
o Handle height position not
rightfor you.
CORRECTION
° Set to "Higher Cut" position.
• Set to"Higher Cut" position.
° Clean/replace air fUtero
= Clean underside of mower housing.
° Check oil level° o Cut at slower walking sp,e,e,d.
o Replace blade.'l]ghten blade bolt.
, Set all wheels at same height o Set engine speed control in fast position.
o Clean underside of mower housing°
° Replace blade.'l]ghten blade bolt.
o Contact an authorized service center.
° Depress control barto upper handle before pulling starter rope.
° Contact an authorized service center°
• Replace blade adapter.
• Move lawn mower to cut grass orto hard surface to start engine.
° Raise cutting height.
° Replace blade.
o Clean grass catcher. o Set engine speed control in fast position.
° Raise cutting height.
° Raise rear of lawn mower housing one (1) setting higher.
• Empty grass catcher.
o Adjust handle height to suit.
17
CRAFTSMAN
Garantia
Reglas de Seguridad
Montaje
OperaciSn
Mantenimiento
Programa de Mantenimiento
Mode! No. 917.377561
17 Especificaciones del Producto
17 Servicio y Adjustes
19 Almacenamiento
20 Identificaci6n de pmblemas
24 Partes de repuesto
24
Orden de Partes
25
27
28
30
Vea el manual ingles del dueSo
Contratapa
GARANTiA LIMITADA DE DOS AltOS PARA LA SEGADORAA MOTOR CRAFTSMAN
Per dos (2) aSos, a partir de ta fechade compm, cuando esta Segadora Craftsman se mantenga, lubrique y afine seg!Jn las instrucciones para la operad6n y el mantenimiento en el manual del dueSo, Sears reparar_ gratis todo defecto en el material y la mano de obra_
Si la Segadore Craftsman se usa para fines comerciales o de arriendo, esta garantia s6lo se apiica por noventa (90) dfas a partir de la fecha de compra.
Esta Garantia no cubre:
o Artfcutos que se desgastan durante el use normaltales como las cuchillassegadoras rotatorias, los adaptadores de la cuchitla, las correas, los filtros de aire y las bujfas° o Reparaciones necesarias debido eLIabuso o a la negligencia del operador, incluy_ndosea los cigfJefales doblados y a la falta de mantenimiento del equipo segSn las instruccionesque se inclL,yen en el manual del due_oo
EL SERVICIO DE GARANT{A ESTA DISPONIBLE al devolver la segadpra a motor Craftsman al centro/ departmento de servicio Sears mas cercano en los Estados Unidos_ Esta garantfa se aplica solamente mientras el producto este en uso en los Estados Unidos.
Esta Garant_a le otorga derechos legates especfficos, y puede que tambi_n tenga otros derechos que varfan de estado a estado.
Sears, Roebuck and Co..,D/817WA, Hoffman Estates, tL 60179 USA
Los estandrares de seguridad exigen la presencia del operatoren loscontmles para reducir a un minimo el riesgo de lesionarse_Su unidad viene equipada con dichos controles. Por ningun motJvo trate del eliminar la funciSn de los controles que exigen la presencia det operador.
ENTRENAM_ENTO:
- Lea este manual del operador cuidadosamente. Familiarfcese con los controles y aprenda a operar su segadora en forma adecuada. Aprenda a parar su segadora r-_pidamente.
• No permita que los niSos usen su segadora,
Nunca perrnita que los adultos operen la segadora sin contar con las inslrucciones adecuadaso o Mantenga el _Sreade operaci6n despejada de gente, especialmente de niScs pequeSos y de anima|es dorn_st_cos
° Use la segadora solamente para los fines propuestos por el fabr_cantey segen fas explicaciones descritas en este manual.
, No opere la segadora si se ha cafdo o daRado en cualquiera forma.. Siempre repare los daRos antes de usarla.
° No use accesorios que no hayan sido recomendados per et fabricante. El uso de dichos accesorios puede ser pelign3soo
• La cuchilla gira cuando el motor est& funcionandoo
PREPARACiON:
° Siempre revise cuidadosamente el &rea que se va a segar y desp_jela de todas las piedras, palos, alambres, huesos y otros objetos extra£_osoEstosobjetos ser&n lanzados con ta cuchilla y pueden producir lesiones graves.
° Siempre use anteojos de seguridad o protectores de ojos cuando arranque y durante e! tiempo que use la segadora_
18
.
Vfstase en forma adecuada. No cpere la segadora sin zapatos o con sandalias mientras que et motor est,. funcionando.
o Siegue siempre durante el dfa o con buena luz artificial.
OPERACION:
o Mantenga sus ojos y su mente en la segadora yen el &rea que se est,. cortando.
No permita que otros intereses Io distraigan.
o No corte c_sped mojado o resbaloso. Nunca corra mientras est_ operando su segadora.
Siempre aseg_rese de mantener el equilibrio
- mantenga el mango agarrado firmemente y camine.
° No ponga las manos o los pies cerca odebajo de las partes rotatodas. Mant_ngase alejado de la abertura de descarga en todo momento.
• Siempre pare el motor cuando se vaya ocuando no est_ usando su segadora, o antes de atravesar las entradas para autos, los senderos, caminos y ,_reas cubiertas de ripio_
o Nunca dirija la descarga del material hacia los espectadores ni permita a nadie cerca de la segadora mientras la est_ operando.
.
Antes de limpiar, inspeccionar o de reparar I a segadora, pare el motor y est_ completamente seguro de que la cuchilla y que todas las partes que se mueven se hayan detenidoo Luego, desconecte el alambre de la bujia y mant_ngalo alejado de
_sta para evitar el arranque por accidenteo
.
No continue haoiendo funcionar su segadora si le pega a un objeto extrafioo Siga el procedimiento descrito anteriormente, tuego repare cualquier dafio antes de volver a arrancar y de operar su segadora.
• No cambie los ajustes del regulador o hagaque el motor ande a una velocidad excesiva. Se pueden producir dafios en el motor y I esiones personaleso
° No opere su segadora si vibra fuera de Io normal. La vibraci6n excesiva es una indicaci6n de dafio; pare el motor, revise en forrna segura la causa de ta vibraci6n y haga las reparaciones segt_n sea necesario.
° No haga funcionar et motor en recintoscerrados° Los gases de escape son peligrososo
° Nunca corte el c_sped tirando la segadora hacia usted. Siegue a trav_s de la cara de las pendientes, nunca hacia arriba o hacia abajo pues puede perder e! equilibric° No siegue pendientes demasiado empinadas.
Tenga cuidado cuando opere la segadora en
terreno disparejo o cuando cambie de direcci6n - mantenga un buen equilibrio.
° Nunca opere la segadora sin tas protecciones adecuadas, las planchas, el recogedor de cSsped y otros dispositivos de seguridad en su lugan
MANTENIMIENTO Y ALMACENAMIEN-
TO:
• Revise la cuchilla y los pemos de montaje det motor a menudo, para asegurarse que estdn apretados en la forrna adecuada.
o Revise todos los pemos, tuercas y tomillos a intervalos frecuentes, para verificar si estdn apretados en forma adecuada, y asegurarseque la segadora se encuentra en condiciones de funcionamiento seguro.
• Mantenga todos los dispositivos de seguridad en su lugar y listos para funcionar.
o Para reducir el peligro de incendio, mantenga el motor sin c_sped, hejas y grasa o aceite en exceso.
.
Revise el recogedor de c_sped a menudo para verificar si hay deterioro y desgaste y cambie las bolsas desgastadaso Use solamente las bolsas de repuesto recomendadas por el fabricante de su segadora o que cumplen con las especificaciones de _ste.
• Siempre mantenga una cuchilla afilada en su segadora.,
.
Siempre permita que el motor se enfrie antes de guardarla en cualquier recinto cerrado_
Nunca guarde la segadora con combustible en et estanque dentro de un edificio endonde los gases pueden alcanzar una llama expuesta o una fuente de ignici6n, tal como el calentador de agua, la estufa de ca!efacciSn, la secadora de ropa, etc.
PRECAUCI6N: Siempre desconecte el alambre de la bujia y p6ngalo donde no pueda entrar en contacto con la bujia, para evitar el
arranque por accidente, durante la preparaciSn, el transporte, el ajuste o cuando se hacen reparaciones.
PRECAUCI6N: Es conocido por el Estado de
Califomia que los gases de escape del motor de este productor contienen quimicos los cuales a ciertos niveles, pueden ocasionar, cdncer, defectos de nacimiento, y otros dafios al sistema reproductivo.
19
Estos acoesorios estaban disponibtes cuando se produjo la segadom. Tambi_n est_n disponibles en la rnayoria de las tiendas de Sears y on los centros de servicio. La mayofia de las Uendas Sears tambi_n pueden rnandara pedir partesde repuesto para usted, si les proporciona el nt_merodel modelo de su segadora. Algunos de estos accesorios tal vez no se apliquen a su segadora,
RENDIMIENTO DE,,I.,A,,,SE_GADORA ........
DESVlADOR DE RECORTES
PARA SEGADORAS CON DESCARGA TRASERA JUEGOS PARA LA ACOLCHADORA ESTABIUZADORES
SEGADORAS
CON DESCARGA
LATERAL
,,,, ..............................
J
ENVASE$
DE GASOUNA
MANTENIMIENTO DE LA SEGADORA i i
8UJfAS
CORREAS
J
SILENCIADORES i,iii %
CUCHILLAS
ADAPTADORES
DE CUCHILLA i ,
RUEDAS i illl
ACEITE
, ,,DELMOTOa
Lea estas instruccionesy este manual
completamente antes de tratar de montar u operar su segadom nueve. Su segadora nueva ha sido montada en la f_0dca con la excepci6n de aquellas partes que se dejaron sin montar por razones de env{o. Todas las partes como las tuercas, las arandelas, los pemos, etc., que son necesarias para completar el montaje hen sido co!ocadas en la belsa de partes. Para asegurarse que su segadora funcione en forma segura y adecuada, todas lee partes y los artfculos de ferreteria que se monten lienen que ser apretados seguramente. Use las
herramJentascorrectas, como sea necesario, para asegurar que se aprieten adecuadamente.
PARA REMOVER LA SEGADORA DE
LA CAJA DE CARTON
• Remueva las partes sueltas que se inclt_en con la segadora.
o Corte las dos esquinas de los extremos de la caja de cart6n y tienda el panel del extrerno piano,
• Remueva todo el material de empaque, excepto la cuF,a entre el mango superior y _1inferior, y la curia que sujeta la barra de los control que exige ta presencia del operador junto con el mango superior.
Haga rodar la segadora hacia afuera de la caja de cartSny revfsela cuidadosarnente para venficar ei todavfa quedan partes sueltas adicionales,
COMO PREPARAR SU SEGADORA
PARA DESDOBLAR EL MANGO
1MPORTANTE: Despliegue el mango con mucho cuidado para no pellizcar loscablesde control.
o Levante los mangos hasta que la secci6n del mango inferior se asegure an su lugar, en la o Levante la secci6n det mango superior hasta su lugar en el mango inferior, remueva la curia protectors y apriete ambas rnan_llasdel mango.
o Remueva ta curia del mango que sujeta la barra de los control que exige la presencia del
operadorjunto con el mango superior.
o Et mango de la segadora puede ajuetarse segSn le acomode para segar. Refi_rase a "AJUSTE
DEL MANGO" en la Secoi6n de Servicio y
Ajustes de este manual.
2O
Barra de contro! que exige la presencia del operado
Mango superior .....
oslci6n para segar
Tapon aicolchadora
Mango inferior
PARA INSTALAR LOS ACCESORIOS
Su segadora fue enviada tista para usarse como una acobhadora de capa vegetal, Para convertirla de modo que pueda ensacar o descargar:
• Abra la puerta trasera y remueva la tapon acolchadora° Gu_rdela en un tugar seguro,
• Ahora puede instalar el recogedor o el desviador de recortes opcionalo
• Para volver a la operaci6n de acolchamiente con capa vegetal, instale la tapon acotchadora en ta abertura de descarga de la segadomo Asegt)rese de que todas las ore]as est_n asentadas en forma adecuad&
PRECAUClON" No haga funcionar su segadora sin la tapon acolchadora aprobada en su lugar, o sin el desviador de recortes, o sin el recogedor de c_sped, aprobados, en su lugar. Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando estA un poco abiertao
21
FAMILIARICESE CON SU SEGADOP,A
LEA ESTE MANUAL DEL DUEllO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU
SEGADORA. Compare las ilustracionescon su segadora para familiarizarsecon la ubicaci6nde los dk,ersos contmles y ajustes. Guarde este manual para referenciaen el futuro.
EstoS's'{m_I0S pueden aPar_er sobre su segadora'0 en la literatura }_'l'oporcionadacon el ...................
producto. Aprenda y comprenda sus significados.
ATTENCI6N O
ADVERTENCIA
MOTOR
ENCENDIDO
MOTOR
APAGADO
R,i_PIDO
Cable de control de zona del motor _..
LENTO ESTRANGU
LACI(_N
COM-
BUSTIBLE
ACEITE PEUGRO, GUARDE LAS
MANOS Y LOS PIES LEJOS
de control que exige ta presencia det operador
Control de impulsi6n
Cord6n
Manilla del mango
Recogedordelc_sped
Tapa del deposito de aceite
del motor con varilla
indicadora de hive!
Cubierta de la
Tapon dens_ acolchadera
Tapa del deposito de la gasolina
Caja
Cebador
CUM'PLE CON LOS REQ'UISITOS DE S'EGURIDAD DE L/_'"c'Psc
Ajustador de la rueda
(en cada rueda)
......................
Las segadoras a motor, que se conducen desde la parte de atr&s, rotatorias, Sears, cumplen con
los est_ndares de seguddad del American National Standards Institute y de la U.So Consumer
Product Safety Commission. La cuchilla gira cuando el motor estd funcionando°
Barra de control que exige la prencia del
operador - tiene que sujetaPse abajo, junto
con el mango, para hacer arrancar el motor°
Su_ltela para parar el motor.
Cebador - bombea combustible adicional
desde el carburador al cilindro para uso cuando se necesita hacer arrancar un motor fr{o.
Cord6n arrancadorse usa para hacer arrancar el motor.
Palanca de control de la impulsi6n - se usa para enganchar la segadora para movimiento hacia adelante impulsada a moron
Tapon de la acolchadera - situada en la abertura de la descarga'y debe ser quitada cuando se convierte la operacciqSn de ensacado a descarga.
22
La operaci6n de cu(31quiersegadora puede hacer qu_ salten objetos extrafios dentro de sus ojos, Io que puede producir dafios graves en
_stos. Siempre use anteojos de seguridad o protecci6n para los ojos mientras opere su segadora o cuando haga ajustes o reparacioneso Recomendamos una mascara de seguridad de visi6n amplia, para uso espejuelos o anteojos de seguridad estandarte.
COMO USAR SU SEGADORA
PRECAUCl6N: No haga funcionar su segadora sin el desviador de recortes o sin el recogedor de c_sped, aprobados, en su lugaroNunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando est_ un poco abierta_
VELOOIDAD DEL MOTOR
La ve!ocidad de! motor se estableci6 en la f&brica para un rendimiento 6ptimo. La velocidad no se puede ajustar.
CONTROL DE ZONA DEL MOTOR
PRECAUOI6N: Las regulaciones federales exigen que se instale un control para el motor en esta segadora para reducir a un mfnimo el
riesgo de lesionarse debido al contacto con la cuchilla. Por ningSn motivo trate de eliminar la funci6n del control del operador, La cuchilla gira cuando el motor est_ funcionando.
o Su segadora viene equipada con una barra de control que exige la presencia del operador, 1o que requiere que el operadorest_ detr&s del mango de la segadora para hacerla arrancar y operarla,
PARA AJUSTAR LA ALTURA DE CORTE
° Levante las medas para el corte bajo y baje las
ruedaspara el corte alto.
.
Ajuste la allure de corte para que se acomode a sus requisites.,La posici6n de! medio es la mejor
para la mayor{a de los c_spedes_ o Para cambiar la altura de corte, empuje la palanca del ajustador hacia ta rueda, Mueva la rueda hacia arriba o hacia abajo de modo que se acomode a sus requisitos. Asegdrese que todas las ruedas queden igualmente ajustadas.
ATENCiON: El ajustador esta correctarnente colocado cuando las orejas de la placa est_n insertadas en el agujero de! mango.
Tambi_n, los ajustes de 9 posiciones (si equipado) permiten que el mango pueda ser movido entre las orejas de la placa.
Para un corte alto, baje tas ruedas ___._
_.__
Orejas de la placa ngo
Para un corte bajo, levante las ruedas
PARA MONTAR Y ADJUNTAR EL
RECOGEDOR DE ClaSPED
• Cierre la tapa sottable. La tapa soltable debe estar cerrada cuando se esta operando la segadom.
o Levante la puerta trasera de la caja de la segadora y ponga el bastidor del recogedor de c_sped en las orejas formadas en el puntal de bisagra de la puerta tmsera.
o El recogedor de c_sped esta asegurado en la caja de la segadora cuando se baja la puerta trasera para descansar en el bastidor del recogedor de c_sped
PRECAUCl6N: No haga funcionar su segadora sin el desviador de recortes o sin el recogedor de c_sped, aprobados, en su lugar. Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando est,. un pc.co abierta.
bisagra _--__
"_/_[ _ _\\
Ore formadas
Puerta trasera
Bastidor del reogedor del esped
PARA VAClAR EL RECOGEDOR DE
C_SPED
° Para remover el recogedor del c_sped suelte la barra de control del operador para poder parar el motor, o Levante la puerta de atras y remova el recogedor del c_sped por el mango.
AVlSO: No arrastre la bolsa cuando la vacfe; se producir& un desgaste innecesarioo
23
CONTROL DE LA IMPULSION
,, La autoimpulsi6n se contmla al sujetar la barra de control que exige la presencia del operador hacia abajo en el mango y al empujar la palanca de control de la impulsi6n hacia adelante hasta que suene "ctic," luego se suelta la palancao
* El movimiento hacia adelante pararA cuando la barra de control que exige la presencia del operador se suelta. Para parar el movimiento hacia adetante sin parar el motor, suelte la barra de control que exige la presencia del operador un poco hasta que se desenganche el control de la impulsi6no Sujete la barra de control que exige la presencia del operador abajo en contra del mango para continuar segando sin autoimputsi6n.
o Para mantener el control de la impulsi6n enganchado cuando se de vuelta en las esquinas, empuje el mango hacia abajo y levante las ruedas detanteras fuera del suelo al girar la segador& control de
_L_',_ la la impulsidn
N\ impulsion para enganchar el control de la impulsi6n control de la impulsi6n desenganchado
ANTES DE HACER ARRANCAR EL
MOTOR
ACEITE
Su segadora rue enviada sin aceite en el motor°
* Aseg0rese que la segadora est_ nivelada y que el &rea alrededor del dep6sito de aceite est6 limpi&
* Remueva la tapa del dep6sito de aceite del motor con la varilla indicadora de nivel y rellene hasta la tfnea de Ileno en _sta.
= Use 20 oz. de aceite° Para el tipo y la calidad vea "MOTOR" en la secci6n de las
Responsabilidades del Cliente en este manual°
.
Vacie el aceite lentamente.
No Io Ilene demasiadoo
.
Revise el nivel del aceite antes de cada usoo
Agregue aceite si es necesado, Llene hasta la Ifnea de Ileno en ta varilla indicadora de niveL
.
Para leer el nivel adecuado, apriete la tapa del dep6sito de aceite del motor cada vez.
* Vuelva a instalar la tapa del dep6sito del aceite y apri6tel&
.
Cambie el aceite despu6s de 25 horas de operaci6n o una vez por temporada.
Puede necesitar cambiar el aceite m&s a menudo cuando las condiciones son polvorosas o sucias,.
GASOLINA
° Llene el estanque de combustible.
Use gasolina regular, sin plomo, nueva y limpia con et minimo de 87 octanos. No mezcle el aceite con la gasolin& Para asegurar que la gasotina utilizada sea fresca compre estanques los cuales puedan ser utilizados durante los primeros 30 dias,,
ADVERTENClA: La experiencia ha indicado que los combustibles mezclados con alcohol (conocidos como gasohol, o el uso de etanol o metanol) pueden atraer la humedad, la que conduce a la separaci6n y formaciOn de #,cidos durante el almacenamientOo La gasolina acfdica puede dafiar el sistema del combustible de un motor durante et almacenamiento
Para evitar los problemas con el motor, se debe vaciar el sistema del combustible antes de guardarlo por un perfodo de 30 dfas o m&so Vacfe el estanque del combustible, haga arrancar el motor y hAgalo funcionar hasta que las Ifneas del combustible y el carburador queden vacfoso La pr6xima temporada use combustible nuevo.
Vea tas Instrucciones
Para El Almacenamiento para mAs informaci6n.
Nunca use productos de timpieza para el motor o para el carburador en el estanque del combustible pues se pueden producir da5os permanentes.
Tapa del
Tapa det deposito de deposito de aceite del motor con la gasolina
".
varilla indicadora de nivel
PARA HACER ARRANCAR EL MOTOR o Para hacer arrancar un motor fifo, empuje el cebador cinco (5) veces antes de tratarlo.
Empuje firmemente.
Este paso normalmente no es necesario cuando se hace arrancar un motor que ya ha estado funcionando pot unos cuantos minutoso
- Sujete la barra de control que exige la presencia del operador abajo en el mango y tire el mango del arrancador r#,pidamenteo No permita que el cord6n arrancador se devuelva abruptamenteo
24
.
Para parar el motor, suelte la barra de control que exige la presencia del operader.
AVISO: En climas m&s frfos puede que sea necesario repetir los pasos del cebado_ En climas m_s calurosos el cebar demasiado puede producir el ahogo y el motor no va a arrancar. Si se ahoga el motor espere unos cuantos minutos antes de tratar de hacerto arrancar y no repita los pasos del cebado,
CONSEJOS PARA SEGAR
• Bajo ciertas condiciones, tal como c_sped muy alto, puede ser necesario el elevar la a_Jra del corte para reducir el esfuerzo necesario para empujar la segadora y para ev'_arsobrecargar el motor, dejando montones de recortes de c_spedo
Puede que sea necesario reducir la velocidad del recorrido y/o haga funcionar la segadora sobre el
_.reapor segunda vez.
o Para un corte muy pesado, reduzca el ancho del corte pasande parcialmente por encima del lugar anteriormente cortado y siegue lentarnente.
• Para un mejor ensacedo del c&sped y para la mayorfa de las condiciones de corte, la velocidad del motor debe ajustarse a la posiciSn de r_pido.
• Cuando use una segadora con descarga trasera
en c_sped h(_medo y pesado, los rnontones del c_sped cortado puede que no entren en el recogedor de c_sped. Reduzca la velocidad del recorrido (velocidad de empuje) y/o haga funcionar ta segadora sobre el &rea por segunda vez.
: Si queda una huel]a de cortes en el lado derecho de una segadera con descarga trasera, siegue en ia direcciSn en que giran tas manillas dal reloj, solapando un poco para recaudar los recortes en la pr6xima pasada.
o Los poros en los recogedores de c_sped de tela pueden Ilenarse con mugre y polvo con el use y los recogedores recaudar-&nmenos c_sped.
Para evitar _sto, roc{e et recogedor con la manguera de agua regularmente y d_jelo secarse antes de usarlo.
o Mantenga la parte superior del motor, alrededor del arrancedor, despejada y sin recortes de c_sped y paja. Esto ayudar'&el flujo del aire del motor y exlender_ su duraci6n.
CONSEJOS PARA SEGAR Y ACOLCHAR
IMPORTANTE: Para obtener el mejor rendimeinto
rnantengala caja de ta segader a sin acumladon de
cesped y basura.Vea "LIMPIEZA" en seccion
de"RESPONSABILIDADES DEL CUENTE" de este manual..
• La cuchilla acolchadora especial va a volver a cortar los recortes de c_pecl muchas veces, y los reduce en tarnaSo, de modo que si se caen en el c_sped se van a dispesar entre _ste y no se van a notar. Tambi_n, el c_sped acelchado se va a deshacer r_pidamente entregando substancies nutritivas para el c_sped. Siempre acolche con la ve!ocidad de! motor (cuchilla) rn_s alta, pues asi se obtendr_ la mejor acci6n de recx_rtede las cuchitlas.
o Evite cortar el c_sped cuando est_ mojado. El c_sped mojado tiende a forrnar montones e intertiere con la acci6n de acolchado. La mejor hora para segar el c_sped es temprano en la tarde. A esa hora _ste se ha secado y el &rea reci_n cortada no quedar& expuesta al so!
directo.
= Para obtener los mejores resultados, ajuste la altura del corte de la segadora de modo clue_sta corte solamente el tercio superior de las hojas de c_sped. En et ceso de que e! c_sped haya crecido demasiado, puede ser necesario el elevar la altura del corte para reducir el esfuerzo necesario para empujar la segadora y para evitar sobrecargar el motor, dejando montones de recortes de c_sped. Para un acolchamiento muy pesado, reduzca el ancho del corte pasando por encima del lugar antefiormente cortado y siegue lentamente.
° Ciertos t_posde c_sped y sus condiciones pueden ex_ir que un _.reatenga que ser acolchada por secjunda vez para esconder completamente los recortes, Cuando se haga el segundo code, siegue atravesado o en forma perpendicular a la pasada de! primer code.
Cambie su patr6n de corte de semana a semana. Siegue de norte a sur una semana y luego carnbie de este a oeste la pr6xima semana. Esto evitar_ que el c_sped se enrede y cambie de direcci6n.
Max_ 1/3
25
,,Ju ,, ................
If Reviser s},,,haysujetaaores sueltos
Limpiar_nspeccionar el recogedor de
S cdsped(siVieneequipado)
E LimPiar la segadora ......
G
Limptar debajo dela cubierta
A mtsi6n(segadorasconpoderpropulsor)
......................
[......
1##
If
O sadas (segedoras.con poder propulsor) _
Revisero/afiladcambtar cuchilla _ i
R 'Tabledetubricaci_n
A Li=nia;labaterfa/recargar
(segedoras con arranque el_ctrico)
....
!
I
_
'_a Reviserelnivetdelaceite.............
Cambiar el aceile de{ motor ....................
"
_
M #
......
!
...............
M#' ....
I
_ 3 i i ,,' v'
I :
I _ 1_1'4
"'Vrl,2
,,_.............
.
oT umptar el tittro de aire .
.
'
If
If 2 R Cambiar
deaim
1 - Camb]arm_s a manudocuandose operebajo cargapesadao en ambtentesconalias tarnperaturas..
2 - Dat setvic|o m&s a menudo cuando se opere en condk:lones suclas o potvorosas
3 - Camble las cuchillas m_ts a menudo cuando stegua err lerreno arenoso
4 - Ca_gar por 48 bores a! fin de la tamporada,,
TABLA DE LUBRiCACi6N
RECOMENDACtONES GENERALES
(_) Ajustadpr de Aceite del
La garant_a de esta segadora no cubre tos artfculos que hart estado sujetos al abuso o ala
;a rueda / motor negligencia del operadoro Para recibir todo el valor de la garantfa, el operador tiene que mantener la segadora segLin las instrucciones descritas en este manual
@,
Hay algunos ajustes que se tienen que hacer en forma peri6dica pare poder mantener su unidad adecuadamente.
Todos los ajustes en la secci6n de Servicio y
Ajustes de este manual tienen que ser revisados pot 1omenos un vez por cada temporada.
-Llna vez al aSo, cambie la buj_a, limpie o cambie el elemento del filtro de aire y revise si la cuchilla est,. desgastada.
Una bujfa nueva y un elemento del filtro de aire limpio/ nuevo aseguran la mezcla de aire-combustibte adecuada y ayudan a que su motor
funcione mejor y que dure m_s,
, Siga el programa de mantenimiento en este manual.
ANTES DE CADA USO
• Revise el nivel del aceite de! motor,
• Revise si hay sujetadores sueltos.
LUBRICACION
(_)ROCtE EL LUBRICANTE
REFIERASE A LA SECCI6N DE
RESPONSABILIDADES DEL C[JENTE EN
"MOTOR"
IMPORTANTE: No acerit o engrase los rodamientos de ta rueda de piastico. Los lubricantes viscosos atraeran polve y mugra, !o
que acortara la duracion de los rodamientos auto lubdcantes. Si cree que lubdcarse, use sotamente un tubdcante tipo grafito, de polve seco, en forma moderada.
Mantenga la unidad bien lubdcada (yea ta
"TABLA DE LUBRICACI6N").
,,®
!_ Clavija de montNe Bisagra de fa de! puntal del puerta trasera mango
26
__
ESPECIFiCACUONES DEL PRODUCTO
NUMERO DE MODELO
NOMERO DE SERtE
FECHA DE COMPRA
CABALLOS DE FUERZA:
DESPLAZAMtENTO:
917.377561
6_5
12,56 CU. IN,
CAPACIDAD
DE GASOLINA:
Y TIPO 1.25 Cuartos
REGULAR SIN PLOMO
TIPO DE ACEITE:
(API-SF/SG/SH)
CAPACIDAD DE ACEITE:
BUJfA (ABERTURA: .030")
TOLERANCIA DE VALVULA:
20 oz. de capacidad
CHAMPION RJ19LM
ADMISION: .004 - °008
DESCARGA: .004 - .008
SENCENDIDO DE ESTADO
SOLIDO ABERTURA DE AIRE:
TORSION DEL PERNO
.0t25
IN.
DE LA CUCHILLA: 35-40 FT. LBS.
. El num_ro del nodelo y el de serie se encuentran en la calcomania adjunta a la parte trasera de la caja de la segadora, Debe registrar tanto el num_ro de serie come la fecha de compra y mantengalos en un lugar seguro para refencia en el futuro.
SEGADORA
Siempre observe las reglas de seguridad cuando haga el mantenimientoo
LLANTAS
• Mantenga las Ilantas sin gasolina, aceite o substancias quimicas para control de insectos que pueden daSar la goma.
o Evite los tocones, las piedras, las grietas profundas, los objetos afilados y otros petEgros que pueden daSar alas Ilantas,
CUIDADO DE LA CUCHILLA
• Remueva el pemo de la cuchilla gir&qdolo en el sentido contrado en que giran las manillas del reloj,,
• Remueva la cuchilla y los art[culos de ferreterfa adjuntadores (el pemo, la arandela de seguridad y la arandela endurecida).
AVlSO: Remueva el adaptador de la cuchilla y revise el cubo interior de la ranura del adaptador de ta cuchitla° La ranura tiene que estar en buenas condiciones para que funcione en forma adecuada.
Carnbie el adaptador si est,. daRado.
Para obtener los mejores resultados, la cuchilla de la segadora tiene que mantenerse affiadao
Cambie la cuchilta doblada o daRada.
PAPA REMOVER LA CUCHILLA
• Desconecte el atambre de la buj[a y pSngalo en donde no pueda entrar en contacto con 6sta.
.
Haga descansar la segadora en su lado.
Asegt3rese que el filtro de aire y que el carburador queden mirando hacia amba.
o Use un bloque de madera entre la cuchifla y la caja de la segadora para evitar que la cuchilIa gire cuando se le quite el pemo.
.
Proteja sus manos con guantes y/o envuelva la cuchilla con una teTagrdesao
PARA CAMBIAR LA CUCHtLLA o Ponga el adaptador de la cuchilla en el cigueSal del motor. Asegt_rese que la ranura del
adaptador y que el chavetero del cigue5al est_n aHneados.
° Ponga la cuchilla en el adaptador de _sta alineando los dos (2) agujeros en la cuchilla con las satientes elevadas en el adaptador.
° Asegurese de que el borde de salida de la cuchilla (opuesto al borde afilado) est8 hacia arriba hacia el motor.
o Instale el pemo de la cuchilla con la arandela de seguridad y la arandela endurecida en el adaptador de la cuchilla y el cigueSaL
27
SAE 30 (sobre 32°F)
SAE 5W-30 (debajo 32°F)
o Use un bloque de madera entre la cuchiga y la caja de la segadora y apdete el pemo de la cuchilla gir_ndolo en el sentido en que giran las rnanillas de! re!oj.
• La torsi6n para apretar recomendada es de 35 -
40 pies libras.
1MPORTANTE: EL PERNO DE LA CUCHILLA ES
CLASE 8 TRATADO A CALOR.
AVISO: No recomendamos el afilar la cuchilla
- pero si 1ohace, asegQrese de que quede balanceada.
PARAAFILAR LA CUCHILLA
Se tiene que tener cuidado de mantenerla balanceada, Una cuchilla que no est_ balanceada va a producir eventualmente daSo en la segadora o
en el motor° o I.a cuchilla puede afilarse con una lima o en una
rueda rectJficadora.No irate de afiiada mientras se encuentra en la segadora.
Para revisar el balance de la cuchitta, clave un clavo en una viga o en la pared. Deje alrededor de una pulgada de un clavo recto expuesto.
Ponga el agujero central de la cuchilla sobre la cabeza del davo., Si la cuchi!la est_ balanceada debe permanecer en la posiciSn horizontal. Si cualquiera de los extremos de la cuchilla se mueve hacia abajo, afile el extremo pesado hasta que _sta quede balanceada.
Adaptador de la cuchilla Chavertero del
Ranura ._.._.--.._cigue_al_.
/ coo,,,,.
5
Perno de / ---_( _,_-/' de Arandela segridad Endurecida Borde de salida
Adaptador de la cuchilla
REECOGEDOR DE C'_SPED
(Si comprado come un accesorio)
o El recogedor de c_sped puede ser rociado con el agua de la manguera pero tiene que estar seco cuando se vaya a usar_
.
Revise su recogedor de c_sped a menudo para verificar si est& daSado o deteriorado. Se va a desgastar con el uso normal. Si se necesita cambiar el recogedor, c__mbielosolamente por uno que sea aprobado por el fabricante. DB el n_mero del modelo de la segadora cuando lo ordeneo
CAJA DE ENGRANAJE[
° Para mantener el sistema de impulsi6n funcionando en forma adecuada, la caja de
engranajes y e! _rea a!rededor de la impulsi6n
tienenque mantenerse limpias y sin acumulaci6n de basura. Umpie debajo de la cubierta de la impulsi6n dos veces por temporada. '
° La caja de engranajes se Ilena con lubricante basra el nivel adecuado en la f&brica_La 0nica vez que el lubdcante necesita atenci6n es cuando se le ha prestadoservicio a la caja de engranajes.
, Si se necesita lubricante, use solamente Grasa
Texaco Starplex Premium 1, Parte No. 750355.
No use substitutos.
RUEDAS DE IMPULSI6N
Revise las ruedasde impulsi6n delanteras carla vez antes de segar, pard asegurarse de que se mueven libremente.
Si las ruedasno giran tibremente quiere decir que hay basura, recortes de c_sped, etc. en el _.reade
las ruedas de impulsi6n y tienen que limpiarse para tiberarlas.
Es necesario limpiarlas ruedas de impulsion; revise ambas ruedas delanteraso
.
Remueva los tapacubos, las cla_as de horquilla y las arandelas.
Remueva las ruedasde los ajustadores de tas nledas.
° Remueva la basura y los recortes de c_sped de dentin de la cubierta contra el polvo, pi56n y/o de los dientes de los engranajes de las ruedas de imputsi6n.
° Ponga las ruedas de vuelta en su lugar.
• Si despu_s de limpiar las ruedas de impulsi6n no giran libremente, p6ngase en contacto con su centro/departamento de servicio autorizado m&s cem._t_.
MOTOR
LUBRlCAOI6N
Use solamente aceite de detergente de alta calidad clasificado con la clasificaci4n SF, SG o SH de servicio APL Seleccione la calidad de viscosidad
SAE segL_nsu temperatura de operaciSn esperada,
I ....
CAUDADES DE VISCOSIDAD DE SAE _,
C ,,_,' .......
.20
-10 .........................
'
AVISO: A pesar de que los aceitesde multMscosidad (5W30, 10W30, etc.) mejoran
el arranque en clima frio, estosaceites de multMscosidad van ha aumentar el consumo de aceite cuando se usan en temperaturas sobre 32° F. Revise el niveldel aceitedel motor m4s a menudo, para e_4tarun posible daSo en el motor, debido a que no tiene suficiente aceite.
" "
28
Gambie e| aceite despues de 25 horas de operaci6n o una vez por temporada.
Puede necesitar cambiar el aceite m_.s a menudo cuando las condiciones sen polvorosas o sucias.
Revise el nivel del aceite del critter antes de arrancar el motor y despu_s de cada cinco (5) horas de uso continuado. Apriete el tap6n del aceite en forma segura cada vez que revise el nivel del aceite.
PARA CAMBIAR ELACEITE DEL MOTOR
AMISO: Antes de inclinar la segadora para drenar el aceite, drene el tanque de combustible haciendo correr el motor hasta que el tanque est_ vacio.
o Desconecte el alarnbre de la bujfa y p6nga!o de modo que no pueda entrar en contacto con _sta.
• Remueva la tapa del dep6sito del aceite; d_jela a t,n lade en una superficie limpia.
o Incline ta segadora y h_gala descansar en su lade y drene el aceite en un envase adecuado.
Mueva la segadora de atrds para adelante para remover todo el aceite que se haya quedado atrapado dentre del motor.
° Limpie todo el aceite derrarnado en la segadera yen el lade del motor.
• Uene el motor con aceite. U_nelo solamente hasta la lrnea de Ileno (FULL) en la vadlla indicadora de niveL NO LO LLENE
DEMASIADO.
° Vuelva a Foner la tapa en el dep6sito del aceite.
o Vuelva a conectar el alambre de la bujfa a _sta.
Envase
FILTRO DE AIRE
Su motor no funcionar_ en forma adecuada y puede sufrir da5os si se usa un filtro de aire sucio.
Cambie el flltro de aire cada afio, y m_s a menudo si siega en condiciones muy polvorosas o sucias. No lave el filtro de aire.
PARA CAMBIAR EL FILTRO DE AIRE
• Remueva el filtro de aire gir_ndolo en el sentido en que gfrela de las manillas del reloj para apretarla, hasta el tope, y retfrelo del cellar.
° Remueva el filtro de la parte interior de la cubierta.
o Limpie la parte interior de la cubierta y el collar para remover toda acumulaci6n de mugre.
o Inserte el filtro nueve en la cubierta.
• Ponga la cubierta det filtro de aire dentro del collar alineando la oreja con la ranurao
, Empuje la cubierta hacia adentro y girela en
el sent|do contrario de las manillas del reloj para apretarlao Gire en el
Abrazadera sentido
Collar
A {as manillas det reloj para
)retarla
Remover
Ranura
Filtro de aire
Oreja del filtero de aire
Gire en el sentido contario las manillas del relojpara apretad
SILENCIADOR tnspecciene y cambie el silenciador si estd.correfdo pues producirun peligm de incendio y/o dafio.
BUJIA
Cambie su bujfa cada afio para hacer que su motor ananque rnds fdcitmentey funcione mejor. Ajuste la
abertura de la bujia en 0.030 pulgada.
LIMPIEZA.
IMPORTANTE: Para obtener el mejor redimientom, mantenga lacajadelasgadorasin acumulacion de cesped y gasura_ Limpie la pa,'te de su segadora despues de carla uso.
PRECAUCION: Desc,onecte el alambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _stao
, Haga descansar la segadera en su lade.
Asegdrese que el firm de aire y que el carburador queden rnirando hacia arriba. Umpie la parte inferior de su segadere msl:_'_ola para remover la acumutaci6n de c_sped y basura.
Limpie el motor a menudo para evitar que se acumule la basura. Un motor tapado funciona rnds caliente y se acorta su durad6n.
• Mantenga las superficies Folidas y las ruedas sin gasolina, aceite, etc.
• No recomendamos el uso de una manguera de jardfn para limpiar la segadora a menos que el sistema el_trico, et silenciador, el fiitrode aJrey el carburador est_n tapados para evitar que les entre el agua. El agua en el motor puede acortar la duraci6n de _ste.
LIMPIE DEBAJO DE LA CUBIERTA DE LA
IMPULSI6N
Umpie debajo de la cubierta de la impulsi6n For Io menos dos veces cada temForada. Raspe debajo de la cubierta con un cuchillo para masiila o con una herramienta parecida, para remover toda acumulaci6n de c_sped o basura en la parte inferior de la cubierta de ta impulsi6n.
29
PRECAUCION: ANTES DE DAR
CUALQUIER SERVICIO O DE HACER
AJUSTES:
• Suelte la barra de control y pare el motor.
° Aseg_rese que la cuchilla y que todas las partes movibles se hayan detenido compIetamente.
o Desconecte et alambre de la bujia y pSngaloen donde no pueda entrar en contacto con _sta.
SEGADOFL_.
PAPA AJUSTAR LA ALTURA DE CORTIE
Vea "PARAAJUSTAR LAALTURA DE CORTE" en
la secciSn de OperaciSn de este manual.
DESVIADOR TRASEERO
Se proporciona un desviador trasero, adjunto entre las ruedastraseras de su segadora, para re_Jucira un mfnimo la posibilidad que objetos scan lanzados hada afuera de la parts trasera de la segadora, en ta posiciSn en donde se encuentra el operador. Si se da_a el desviador debe cambiarse.
PAPA REMOVEPJCAMBIAR LA CORREA
DE
IMPULSK')N
° Remueva la cubieda de la impulsidn. Remueva la correa empujando hacia abajo en la potea de
la caja de engranajes.
o Haga descansar la segadora en su lado con el
I1ftrode airs y el carburador mirando hacia amba.
• Remueva fa cuchitla.
.
Remueva la defensa en contra del desperdicioo
• Remueva la correa de la polea del motor en el ciguefaL
•lnstale la correa nueva siguienc_olospasos anteriores en el orden inverso°
• Siempre use la correa aprobada por la f_brica
para asegurarse que calce y dure.
• Remueva las abrazaderas dot cable_
Remueva los controfes y la barra de control que exige la presencia del operador del mango superior.
Remueva la gufa del cordSn arrancador dot mango inferior°
Remueva las clavijas de horquilla..
Desconecte el mango inferiorde los puntales dot mango (.
° De vuelta el mango y vuelva a montar las clavijas de holquitla que se habian removido.
° Vuek,a a montar la gui'a dotcorddn arrancador_
• Vuelva a montar los controles y la barra de control que exJgela presencia del operador en el mango superior.
PRECAUCiON.
La barra de control que la exige presencia del operador tiene que pivotear libremente para permitir el enganche de la cuchUla/freno cuando se suelta la barra de control No apdete dem&siado los sujetadores que sujetan a tos controles al mango superior.
o Para cambiar de ta posidSn de mediana baja a
aJtasolamante se tendrd que dar vuelta Ia secciSn del mango superior.
° Para cambiarde la posiciSn mediana baja a baja, solamente se tend_ que dar vuelta la secci6n del mango inferior.
PosiciSn de envio
Mediana baja
Mediana alta
Cubierta
de la impulsion
Empujar hacia abajo
PAPA AJUSTAR EL MANGO
Se puede levantar o bajar e! mango de su segadora seg_n le quede c6modo, Hay cuatro (4) posiciones disponibles: alta, rnediana a_ta,mediana baja, bajao
Los mangos se env_anmontados en la posici6n mediana baja.
o Para cambiar de la posidSn mediana baja a mediana alta, la seccidn superior y la inferior del mango tendrdn que darse vuelta_
Apriete para remover
Abrazadera de
3O gorquilta
Alta Baja
Mango inferior
Puntal det mango
MOTOR
VELOCIDAD DEL MOTOR
La velocidad del motor ha sido ajustada en la f_bricao No trate de aumentar la velocidad del motor pues se pueden producir lesiones personales.
Si cree que el motor est,, funcionando demasiado r_pido o demasiado lento, Ileve su segadora a un centroi departamento de servicio autodzado para repararla o ajustaflao
CARBURADOR
Su carburador no es ajustable, Si su motor no est& funcionando en forma adecuada debido a
problemas que se sospecha vienen del carburador, lleve su segadora a un centro de servicio autorizado para reparada y/o ajustarla.
IMPORTANTE: Nunca maniputee el regulador del motor, et que ha sido ajustado en lafabrica ara la velicidaddel motor adecuada, puede ser peligroso hacer funcionar el motor a una velocaded por sobre el ajuste de ata velocidad atta regulada del motor necesita ajuste, pongase en contacto con su centro departamento de servicio autorazado mas cerano, el que cuenta con el equipo adecuado y la experiencia para haacer los ajustes necesarios.
Inmediatamenteprepare su segadora para eI almacenamiento al finalde cada temporada o si la unidad no se va a usar por 30 dfas o m,_so
SEGADORA
Cuando se va a guardar la segadora por cierto perfodo de tiempo, Ifmpiela cuidadosamente, remueva toda la mugre, la grasa, las hojas, etc.
Gu_rdela en un &rea limpia y seca.
° Limpie toda la segadora (Vea "L1MPIEZA" en la secciSn de Responsabilidades del Cliente de
este manual).
* Lubrfqueta segun se muestra en la secci6n de
Responsabilidades del Cliente de este manual.
.
Aseg0rese de que todas las tuercas y clavijas y todos los pemos y tornillos est_n apretados en foma segurao Inspeccione las partes que se mueven para verificar si est_n daSadas, quebradas o desgastadas. C&mbielas si es necesario,.
.
Ret_lue todas tas superficies que est6n oxidadas o con la pintura picada; use una lija antes de pintar_
MANGO
Puede doblar el mango de su segadora para aJmacenarta.
* Apriete los extremos inferioresdel mango inferior entre sf hasta clueel mango inferiorquede separado de! puntal del mango, luego mu_valo hacia adelante.
o Suelte los pemos de montaje del mango superior
Io suficiente como para permitir que el mango superior se pueda doblar hacia atraso
Mango inferior
Puntal del mango
Clavija de horquilla
Barra de control que exige la presencia del operado
Mango superior
Levantar ci6n para segar
Mango inferior
IMPORTANTE: Cuando doble el mango para el alacenamiento o el trasporte, asegurese que Io doble segun se muestra o puede danar los cables de control.
° Cuando prepare sus mangos a partirde la posici6n de almacenamiento, el mango inferior autorr_ticamente se asegumr'& en la posici6n para segar_
MOTOR
SISTEMA DE COMBUSTIBLE
IMPORTANTE: Es importanteevitarque se formen depositos de pares fundamentales del sistema de comustible tales como el carburador, el filtro del combutible, la manguera del combustible o en el estanque durante el almacenmiento. La experiencea tambien endica que los combustibles mezctados con alcohol (conecido come gasohol o que tienen etanol o metano!) pueden atraer humedad, 1oque conduce a la separati6n y a la formaci6n de &cidos durante almacemamiento, la gasolina &cideca puede naSar el sistema de combustible de un motor durante el perido de alcamenmiento.
31
o Dren e e I estanq e de combustibl e.
._,
• Haga arrancar el motor y d_jelo funcionar _sta que las Iineas del combustible y el carburador est_n vac[os.
o Nunca use los pmductes para limpieza del carburador o del motor en el estanque de combustible pues se pueden producir da_os permanentes,
o Llse combustible nuevo la pr6xima temporada.
AVlSO: El estabilizador de combustible es una altemativa aceptable para reducir a un minimo la formaci6n de dep6sitos de gorna en el combustible durante el perfodo de almacenamientoo Agregue estabilizador a la gasolina en el estanque de combustible o en el envase para el almacenamiento_ Siempre siga la proporciSn de mezcla que se encuentra en el envase del estabilizador,
Haga funcionar el motor por !o menos 10 minutos despu_s de agregar el estabilizador, para permi_r que este Itegue al carburador_ No drone la gasolina del estanque de gasolina y
el carburador si se est_ usando estabilizador de combustible_
ACEITE DEL MOTOR
Drene e! aceite (con el motor caliente) y c&mbielo con aceite de motor timpio. (Vea "MOTOR" en la secci6n de Responsabilidades del Cliente de este manual.)
ClUNDRO o Remueva la bujia.
• Vacie una onza (29 ml) de aceite a trav6s del agujero de la bujfa en e! cilindro.
o Tire la manilta de arranque lentamente unas cuantas veces para distribuir el aceite.
° Vuelva a monlar la nueva bujfa,
OTROS o No guarde la gasolina de una temporada a la otra,
° Cambie el envase de la gasotina si se empieza a oxidar. La oxidaciOn y/o la mugre en su gasolina producir_n problemas.
• Si es posible, guarde su unidad en un recinto cerrado y c_brala para protegerla contra el polvo y la mugre.
• Cubra st] unidad con un forro protector adecuado que no retenga la humedad. No use pt_.stico El pl__sticono puede respirar, Io que perrnite la formaci6n de condensaciSn, Io que producir_ la oxidaciOn de su unidad
IMPORTANTE: Nunca cubra la segadora mientras
el motor y las areas de escape todavia estan caJientes.
PRECAUCION: Nunca almacene la segadora
con gasolina en el estanque dentro de un edfficio en donde los gases pueden alcanzar una llama expuesta o una chispa.
Pen'nita que se enfrfe el motor antes de almacenarta en alg_n recinto cerrado.
32
IDENTIFICACI6N
PROBLEMA
No arranca
Falta de fuerza
DE PROBLEMAS
CAUSA o Filtro de aire sucio,
, Sin combustible.
=Combustible rancio,
. Agua en el combustible,
• Alambre de la buj/a desconectado,
- Bujia mala.
CORRECCI6N
• Limpie!cambie
el filtro de aire.
= Llene el estanque de combustible°
° Drene el estanque y vuelva a
Ilenario con combustible limpio y nuevo.
o Drene et estanque de combustible y el carburador y vuelva a llenar el estanque con gasolina nueva,
° Conecte el alambre a la bujfa,
o Cambie la bujia.
• Apriete el perno de la cuchilla o cambie e! adaptador de la cuchilla_
° Presione ta barra de control hacia el mango.
• Cambie la barra de control.
- Cuchilla suelta o adaptador de la cuchilla quebradoo
=Barra de control en la posiciSn suelta.
• Barra de control defectuosa, o Ajuste a fa posici6n de "Corte m&s alto."
• Parte trasera de la cajacuchilla de la segadoraarrastr,_ndose
en el c_sped pesado,
• Est& cortando mucho c_sped.
° Filtro de aire sucio, i° Ajuste a la posici6n de "Corte m&s alto?
• Limpie/cambie el filtro de aire.
o Limpie la parte inferior de la caja de la segadora,
• Revise el nivel del aceite.
• AcumutaciSn de c_sped, hojas y basura debajo de la segadora,
° Demasiado aceite en el motor_ t o Corte a una velocidad de recorrido
m_.slenta o
33
PROBLEIVIA
Ma! corte -_lisparejo
Vibraci6n excesiva
CAUSA CORRECClON o o o
Cuchilla desgastada, suelta.
doblada o
Altura de las ruedas dispareja,
Velocidad del motor lenta.
Acumulaci6n de c_sped, hojas o basura debajo de la segadora.
= Cambie la cuchilla. Apriete" el pemo de la cuchilla.
= Ajuste todas las ruedas a la misma altura.
• P6ngase en contacto con su centro de servicio autodzado m_s cercano.
• Limpie la parte inferior de la caja de la segadorao
= Cuchilla desgastada, doblada o suelta,
= Ciguefial del motor doblado.
= Cambie la cuchilla. Apriete el
pemo de la cuchilla,
= P6ngase en contacto con su
, centro de servicie auto_zado
......
!
'A;' :'_¢;",':.
...._=_._-_.=
cor 6rlarrancaao :
• Et freno_de._:V.o!antedel,motor i:_:
,;e.s!a.apl!_cf_cuand0
_e sueita diffcil de tirar " " " la barra de control.
:- ,'-
,,;-;P#eSionelabarra de contr,! .....
._!,÷_
: hac!a el niahgo Superi6r an(_',a_:"!
tirar el cord6n arrancador.; ":;-_i ; i ;
= CigueSal del motor dobladoo
• Adaptador de la cuchilla quebradoo
.
La cuchilla se arrastra en el c_sped.
_,
.
P6ngase en contacto con sd', centro de servicio autorizado m&s cercano. ""
• Cambie el adaptador de ta cuchilla° '
Mueva la segadora a un lugar en donde el cdsped ha sido cortado o a una superficie firme para , hacer arrancar el motor.
H
......
Recogedor de c_sped no se Ilena (si viene equipado)
.
Altura de code demasiado baja+
• Levantamiento de la cuchilla desgastado.
.
Recogedor sin ventilaci6n de aire.
Velocidad del motor lenta.
o
•
•
Eleve ia altura de code.
Cambie la cuchillas.
Limpie el recogedor de c_sped_
Ajuste el control de la velocidad de! motor a la posici6n r_pida
Dificil de empujar
.
El c6sped estd demasiado alto o la altura de la rueda demasiado bajao
Parte trasera de la caja/cuchilla de la segadora en el c6sped.
arrastrdnclose
• Recogedor de c_sped demasiado Iteno.
• Posici6n de la altura del mango no adecuada para usted_
.
Eleve la altura de code,,
Eleve la parte trasera de la caja de la segadora (1) un lugar m_,s alto.
• Vacie el recogedor de c_sped.
. Ajuste la altura del mango de modo que le acomode.
34
ROTARY LAWN MOWER -- MODEL NO. 917.377561
GEAR CASE ASSEMBLY PART NUMBER 702511
J f
17 t i
KEY
NO_
2
3
4
6
PART
NO.
17490416
137055X004
137053
57072
48373
77881
137051
DESCRIPTION
KEY
NO.
PART
NO.
Tapping Screw 1/4-20 x
1-1/4
Engagement Bracket
Shifter
Seal
Gear Case Halves Kit t0
9
11
I2
137074
57079
131484
700343
13 86447
!4
137050
(Includes Key Nos_ 4, 5, 15 750436X and 7) 16 750369
Bearing
Worm Shaft
17
18
19
12000003
850848
81585X004
NOTE: All component dimensions given in UoS. inches. 1 inch = 25.4 mm
DESCRIPTION
Drive Shaft
Hardened Washer
Clutch Yoke
Bushing
Plug
Helical Gear
Clutch Jaw
Grease
E-Ring
Hi-Pro Key
Spring Bracket
35
61
ROTARY LAWN MOWER MODEL NUMBER 917.377561
12
10 14
22
!_23
35
31
28
12 co
O'_
69
25
27
28
29
30
32
34
53
2037
55
56
F,
52
41
44
Jl
KEY
NO.
PART
NO.
1 145646X479
2 156577
4 150425
5 66426
6 136376
8 145793
9 151023
10 128415
11
12
150050
STD512505
27
28
29
30
31
32
34
35
37
13 63601
14 156374X479
15 t6
700365X479
!33190X479
17 140661)(479
20 140540
22 85543
23
25
26
87677
83923
57143
151138
142748
61651
750913X004
701037
700331){004
146630
700325X007
150078
38
39
40
88348
161814}(479
161812)(479
ROTARY LAWN MOWER MODEL NUMBER 917.377561
DESCRIPTION
Upper Handle
Engine Zone Control Cable
Muicher Plug
Wire Tie
Handle Knob
Control Bar
Rear Door Kit
Pop Rivet
Self Tapping Screw #t0-24 x 5/6
HexTapping Screw w/Seres !/4-20 x 1/
2
Nut 1/4-20
Back Plate
Side Baffle
Discharge Baffle
Rear Baffle
Rear Skirt
Engine Pulley
Hi-Pro Key #505
Hex Flange Nut
Wave Washer
Wheel
Shoulder Bolt 3/8-16 x I
Spring Washer
Axle Arm Assembly
Selector Knob
Selector Spring
Spacer
Wheel Adjusting Bracket
Thread Cutting Screww/Sems 5/16-18 x 3/4
Fiat Washer 318
Handle Bracket Assembly (Left)
Handle Bracket Assembly (Right)
KEY PART
NO.
NO.
41 1504O6
DESCRIPTION
44
46
47
48
49
50
161769
851514
157101
851074
850263
851084
51 700869X479
52 85463
53
55
59
61
62
64
74760612
751592
56 88652
57 51793
58 157081X479
131959
132001
134612
......
69151440
- 164569
Hex Head Thread Rolling Screw
3/8-16 x 1-1/8
Lawn Mower Housing (Incl. Key
#14, 15, 51 & 52)
Blade Adapter
Blade 22"
Hardened Washer
Helical Washer 3/8-24 x 1-3/8 Gr.
8
Hex Head Machine Screw 3/8-24 x 1-3/8 Gr. 8
Front Baffle
Danger Decal
Hex Bolt 318-16 x3/4
LocKnut 3/8-16
Hinge Screw 1/4-20 x 1-1/4
Hairpin Cotter
Lower Handle
Handle Bolt
Rope Guide
Debris Shield
Engine - (See Breakdown)
Tecumseh 143.986500
Hub caps
Owner's Manual (English/
Spanish)
Available accessories not included with fawn mower:
- 1..1.33303
..
71 33623
- 71 33500
- 71 33300
- - 7t 33417
- 71 33316
Clipping Deflector
Gas Can (2.5 gal.)
Fuel Stabilizer
SAE 30W Oil (20 oz.)
Dust Shield
Mower Cover
co
ROTARY LAWN MOWER MODEL NUMBER 917.377561
14
12
13
¢.o
c_
ROTARY LAWN MOWER MODEL NUMBER 917.377561
KEY
NO.
PART
NO.
12
13
14
15
16 t0
9
11
5
6
8
1 145755
2 48385
3 751152
4 158755
146527
150495
150182
145212
88446
150340
12000058
137054
88080
88118
67725
DESCRIPTION KEY
NO.
Control Cable
Assembly
Control Head Kit
Locknut #10-24
Pan Head Machine
Screw 1/4 x 20
V-Belt
Spring Retainer
Hubcap
Flanged Nut
Nylon Bushing
Wheel & Tire
Assembly
E-Ring
Pinion
Dust Cover
Felt Washer
Washer 1/2 x 1-1/2 x .134
! 8 701037
26 143603
28
31
32
33
35
154990
132010
137052
48386
151521
36 702511
37 t37090
38 STD541425
40 75192
_4t _ 151520
53
54
144747
154870
55 86012
57 144748
PART
NO.
DESCRIPTION
Selector Knob
Hex Washer Head Screw
#10-24 x 3/4
Drive Cover
Hex Flange Nut
Drive Pultey
Drive Control Cable Kit
Wheel Adiuster
Assembly (Left)
Gear Case Assembly
Spring
Locknut 1/4-20
Spnng
Wheel Adluster
Assembly (Right)
Frame Throat
Grassbag
Driveshaft Cover
Frame Tube
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143,986500
400
130
416
120
119
46
4O
CRAFTSMAN 4-CYCLE ENGINE .............
KEY
NO.
PART
NO, t 36774
2 26727
6 33734
7 36557
12 36775
12A 36558
12B 36694
14 28277
15 30589
16 34839A
17 31335
! 8 651018
19 36281
20 32600
30 35801
40 40027
40 40028
41 40025
41 40026
42 40006
42 40007
43 20381
45 36777
46 32610A
48 27241
50 36778
52 29914
69 35261
70 35995
72 30572
73 28833
75 27897
80 30574A
81 30590A
62 30591
83 30588A
86 650488
89 611004
90 611112
92 650815
93 650816
I00 34443B t01
I03
610118
651007
1t 0 37047
119 36787
120 36825
126 36779
125 36780
126 36781 t26 36782
130 602tA
DESCRIPTION
Cylinder (Incl. 2 & 20)
Dowel Pin
Breather Element
Breather Assay.. (inct. 6 &
12A}
Breather Tube
Breather Cover & Tube
(Inclo12B)
Breather Tube Elbow
Washer
Govemor Rod (IncL 14)
Governor Lever
Governor Lever Clamp
Screw, Torx T-15, 8-32 x
19/64"
Extension Spr_ng
Oil Seal
Crankshaft
Piston, Pin & Ring Set
(Stale)
Piston, Pin & Ring Set
(.010" OS)
Piston & Pin Assay. (Std.)
(IncL43)
Piston & Pin Ass'y.
(.010" OS) (Incl. 43)
RingSet (Std.)
Ring Set (.010" OS)
Piston Pin Retaining Ring
Conna_ng Rod Ass'y_
(Inc[ 46}
Conne_ng Rod Bolt
Valve Ufter
Camshaft (MCR)
Oil Pump Ass'y,.
* Mounting Flange Gasket
MountingFlange (IncL72 thra 83)
Oil Drain Plug(ind. 73)
Drain Rug Gasket
Oil Sea!
Governor Shaft
Washer
GovernorGear Assay,.
(IncL 81)
Governor Spool
Screw, 1/4-20 x 1-1/4"
Flywheel Key
Flywheel
BellevitZeWasher
Flywheel Nut
SolidState Ignition
Spark PlugCover
Screw, Terx T-t5, 10-24 x
15/t 6"
Ground Wire
* Cylinder Head Gasket
Cylinder Head
Exhaust Valve (Std.) (Incl,
151)
Exhaust Valve (1/32" OS)
(inct. 151)
Intake Valve (Std.) (Inct,
151)
Intake Valve (t/32" OS)
(Inr_,151)
Screw, 5/1@18 x 1-1/2"
MODEL NUMBER 143.986500
KEY
NO,
PART
NO.
DESCRIPTION
135
150 t 74
184
185
!86
903_-
900
35395
35991
151 31673 t61A 40017
169 36783 t 72 36784
30200
178 29752
182 6201
26756
36785
32653
169 650839
191 36559
195 610973
207 34336
2!6
33086
223 650451
224 36786
238 650932
239 34338
241 36919
245 36905
250 38920
260 36980
261 30200
262 650831
263A 36921
275 36790
277 650888
285 35000A
287 650926
290 29774
292 26460
298 28763
300 36916
301 38248
305 35647
306
307 35499
309 650562
310 35648
313 34080
347 651038
370A 36261
3700 36861
380 640069
390 590702
400 36792B
416
417
36996
36085
650760
----
Resister Spark PIug
(F_J19LM)
Valve Spdng
Valve SpringCap
Intake Valve Seal
* ValveC.,overGasket
Valve Cover
Screw, 10-24 x 9/16"
Nut& Lock Washer, 1/4-28
Screw, 1/4-28 x 7/8"
"Carburetor To Intake Pipe
Gasket
Intake Pipe
Govemor Link
Screw, 1/4-20 x 3/8"
S.E. Brake Bracket
(Include, 195)
Terminal
Throttle Link
R.P.M. Adjusting Lever
Screw, 1/4-20 x !"
" Intake Pipe Gasket
Screw, 10-32 x 49/64"
* Air Cleaner Gasket
Air Cleaner Cellar
Air Cleaner Filter
Air CleanerCover
Blower Housing
Screw, 10-24 x 9/16"
Screw, !/4-20 x 1/2"
Starter Gdll
Muffler
Screw, 1/4-20 x 2-5/16"
Starter Cup
Screw, 8-32 x 21/64"
Fuel Line
Fuel Line Clamp
Screw, 1032 x 35/64"
Fuel Tank (Include.292 &
301)
Fuel Cap
Oi! FilITube
* "O_-Rfng
=O-Ring
Screw, 1@32x 1/2"
D_pstick
Spacer
Screw, 10-32 x 51164"
LubricaSonDecal
Primer Decal
Carburetor (IncL 184)
Rewind Starter
Gasket Set
(Inct. Items Marked" )
Spark Arrestor Kit
(!ncL 417)(Optional)
Screw, 8-32 x 3/8"
(Optional)
Replacement Engine
NONE
Replacement S/B 750832, order from 71-999)o
RPM High 2900 to 3200
NOTE: This engine could have been built with590739 starter.
NOTE: AUcomponent dimensions given in US. inches
1 Inch = 25 4 mm
41
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.986500
K_
N_
PART
N_
640O69
631615
631767
631184
631183
64OO70
65O,5O6
632527
651025
63O766
64O027
64OO53
631867
631024
632019
531028
631021
631022
36045A
632735
632547
64OO3O
27110
630748
631O27
3O
31
35
36
37
4O
44
47
48
18
20
20A
25
27
28
29
7
16
17
4
5
6
1
2
,to
DESCRIPTION
Carburetor
(IncL t84 of Engine Parts List
"FnrottJeShaft & Lever Assembly
ThmWe Return Spring
Dust Seal Washer
Dust Seal (Throt_)
ThrottJeShutter
Shutter Screw
Fuel Fitting
Thro_e Crack Screw/
Idle Speed Screw
Tension Spring
Idle Restdctor Screw
Idle Res_ctor Screw Cap
Float Bowl
Roat Shaft
Float
Float Bowl '_" Ring
InletNeedle, Seat, & Clip (Inclo31)
SpringClip
PrimerBulb/Retainer Ring
Main Nozzle Tube
"O"Ring,Main NozzleTube
High Speed Bowl Nut
Bowl Nut Washer
Welch Plug, Idle Mixture Well •
Welch Plug, Atmospheric Vent
42
CRAFTSMAN 4-CYCLEENGINE ............
KEY PART
NO.
NO.
-590702
1 590699A
2
3
4
5
6
7
8
590600
590696
590601
590697
590698
590699
590700
11
12
590703
13
590535
590701
MODELNUMBER 143.986500
DESCRIPTION
Recoil Starter
Spring Pin (tnclo 4)
Washer
Retainer
Washer
Brake Spring
Starter Dog
Dog Spring
Pulley & Rewind Spr_ng
Ass'y,,
Starter Housing Ass'y.
(40 degree grommet)
Starter Rope ( 98" X 9/
64" dia)
Starter Handle
KEY PART
NO.NO
590739
3 590740
6 590616
7 590617
8 590618A
11 590638
12
13
14
590535
590701
590741
DESCRIPTION
Rewind Starter
Retainer
Starter Dog
Dog Spring
Pulley & Rewind Spring
Assty
Starter Housing Assty
(40 degree grommet)
Starter Rope
(Length 98" x 9t64" dia,)
Starter Handte
Locking Tab
43
For the repair or replacement parts you need delivered directly to your home
Call 7 am - 7 pm, 7 days a week
1-800=366=PART
(1-800-366-7278)
Para ordenar piezas con entrega a domicilio - 1-800-659-7084
For in-house major brand repair service
Cal! 24 hours a day, 7 days a week
1=800=4=REPAIR
(t -800-473-7274)
Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811
For the location of a Sears Parts and
Repair Center in your area
Call 24 hours a day, 7 days a week
1=800-488=1222
For information on purchasing a Sears
Maintenance Agreement or to inquire about an existing Agreement
Call 9 am - 5 pro, Monday-Saturday
1=800=827=6655
When requesting service or ordering parts, always provide the following information:
• Product Type = Part Number
• Model Number o Part Description
164569 REV.2
02.03.98
VB
Amenca's Repair Specia/lsts
Printed in U.SoA.
advertisement