Multitech GFU19 User manual
Διαφήμιση
Διαφήμιση
Version 7.0
English
Leica GPS1200+
User Manual
Introduction
Introduction
Purchase
Product identification
GPS1200+ 2
Congratulations on the purchase of a GPS1200+ series instrument.
This manual contains important safety directions as well as instructions for setting
up the product and operating it. Refer to "6 Safety Directions" for further information.
Read carefully through the User Manual before you switch on the product.
The type and the serial number of your product are indicated on the type plate.
Enter the type and serial number in your manual and always refer to this information when you need to contact your agency or Leica Geosystems authorized service workshop.
Type:
Serial No.:
_______________
_______________
Symbols
Trademarks
Introduction
The symbols used in this manual have the following meanings:
Type
Danger
)
Warning
Caution
Description
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor or moderate injury and/or appreciable material, financial and environmental damage.
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.
• Windows and Windows CE are a registered trademark of Microsoft Corporation
• CompactFlash and CF are trademarks of SanDisk Corporation
• Bluetooth is a registered trademark of Bluetooth SIG, Inc
All other trademarks are the property of their respective owners.
GPS1200+ 3
Introduction
Validity of this manual
Illustrations
Available documentation
GPS1200+ 4
• This manual applies to all GPS1200+ instruments. Differences between the various models are marked and described.
• The RX1200 is available as RX1210 or with touch screen functionality as
RX1210T, RX1250X, RX1250Xc, RX1250T or RX1250Tc. The name RX1210 is used throughout the manual and may also represent the touch screen models.
Only use the supplied stylus on the screens of the touch screen models.
For the purpose of the illustrations, a GX1230+ model has been selected which is representative for all models.
Name Description Format
User Manual All instructions required in order to operate the product to a basic level are contained in the User
Manual. Provides an overview of the product together with technical data and safety directions.
x x
Introduction
Name Description Format
System Field
Manual
Applications
Field Manual
Technical
Reference
Manual
Describes the general working of the product in standard use. Intended as a quick reference field guide.
Describes specific onboard application programs in standard use. Intended as a quick reference field guide. The RoadRunner application program is described in a separate manual.
Overall comprehensive guide to the product and program functions. Included are detailed descriptions of special software/hardware settings and software/hardware functions intended for technical specialists.
x
x x x
Refer to the following resources for all GPS1200+ documentation and software:
• the SmartWorx DVD
• http://www.leica-geosystems.com/downloads
GPS1200+ 5
Table of Contents
Table of Contents
In this manual
GPS1200+
Chapter
Data Storage and Data Conversion Concept
6
Page
Table of Contents
3.3 Working with the CompactFlash Card
3.4 Working with the Clip-On-Housings for Devices
3.5 Accessing Survey Application Program
3.6 Guidelines for Correct Results
3.7 Operation with a Typical Configuration Set
4.3 Getting Started with the GRX1200+ Series
GPS1200+
7
Table of Contents GPS1200+
6.6 Electromagnetic Compatibility EMC
6.7 FCC Statement, Applicable in U.S.
Tracking Characteristics of the Receiver
7.4 Conformity to National Regulations
GFU19 (US), GFU25 (CAN), GFU26 (US) CDMA
8
8 International Limited Warranty, Software License Agreement
Table of Contents GPS1200+ 9
Description of the System
1
1.1
GPS1200+
Description of the System
System Components
Main components
10
Component
Receiver
RX1200
Antenna
Description
To calculate a range to all visible satellites.
To operate the user interface either by the keyboard or by the touch screen with supplied stylus.
To receive the satellite signals from the GNSS (Global
Navigation Satellite System) satellites.
LEICA Geo Office The office software including a series of help programs which support working with GPS1200+.
LEICA GNSS Spider The reference station software required to operate the reference station receivers of GPS1200+.
Receivers
Depending on the satellite systems and signals configured in CONFIGURE Satellite
Settings
a maximum number of 120 channels is allocated.
Receiver
GX1230+ GNSS
GX1230+
GX1220+ GNSS
GX1220+
GX1210+
GX1200+ with
PPS/Event option
Description
Up to 16 L1, 16 L2, 16 L5 channels (GPS), up to 14 L1, 14 L2 channels (GLONASS), up to 14 E1, 14 E5a, 14 E5b, 14 Alt-
BOC channels (Galileo), four channels SBAS, code and phase, real-time capable
16 L1, 16 L2 channels (GPS), four channels SBAS, code and phase, real-time capable
Up to 16 L1, 16 L2, 16 L5 channels (GPS), up to 14 L1, 14 L2 channels (GLONASS), up to 14 E1, 14 E5a, 14 E5b, 14 Alt-
BOC channels (Galileo), four channels SBAS, code and phase
16 L1, 16 L2 (GPS) channels, four channels SBAS, code and phase
16 L1 channels (GPS), four channels SBAS, code and phase
16 L1, 16 L2 channels (GPS), code and phase, real-time capable, with event and PPS ports
Description of the System GPS1200+ 11
Description of the System GPS1200+ 12
Receiver
GRX1200+
Description
16 L1, 16 L2 channels (GPS), code and phase, real-time capable, with event, PPS, oscillator and NET port, for reference station applications
GRX1200+ GNSS Up to 16 L1, 16 L2, 16 L5 channels (GPS), up to 14 L1, 14 L2 channels (GLONASS), up to 14 E1, 14 E5a, 14 E5b, 14 Alt-
BOC channels (Galileo), code and phase, real-time capable, with event, PPS, oscillator and NET port, for reference station applications
)
)
)
Once the first operational Galileo satellites are available, a software update will be required.
The GX1230+ GNSS, GX1220+ GNSS, and GRX1200+ GNSS receivers are additionally designed to support Compass. The Compass signal definition is not fully finalized, although, test signals have been tracked in a test environment. As changes may still occur, Leica Geosystems cannot guarantee full Compass compatibility.
The GX1230+ GNSS, GX1230+, GX1220+ GNSS, GX1220+, GX1200+ with
PPS/Event option and GRX1200+ Series receivers use the GPS P-code signal, which by U.S. policy is liable to be switched off without notice. Phase measurements
Antennas used with receivers on L2 are ensured as these receivers automatically switch to patented tracking techniques.
Receiver
GX1230+ GNSS/GX1230+/
GX1220+ GNSS/GX1220+
GX1210+
GRX1200+ Series
Antenna
Typically: AX1203+ GNSS, otherwise: AT504 GG/
AR25
AX1201
Typically: AT504 GG/AR25 otherwise:
AX1203+ GNSS
Description of the System GPS1200+ 13
Description of the System
LEICA Geo Office
GPS1200+ 14
• LGO supports the GPS1200+ and TPS1200+ instruments. It also supports all other Leica TPS instruments.
• LGO is based on a graphical user interface with standard Windows® operating procedures.
• LGO provides the following functionality:
Functionality Description
Standard Functionality
Includes data exchange between computer and receiver, data management including viewing and editing, reporting, creation and management of codelists, creation and use of format files for data conversion, uploading and deleting of system software and application programs.
Extended Functionality
Includes coordinate transformations, GPS and GLONASS post processing, level data processing, network adjustment, GIS and
CAD Export.
• Supported operating systems: Windows® XP, Windows® 2000.
Refer to the online help of LGO for additional information.
LEICA GNSS
Spider
The reference station software is known as LEICA GNSS Spider. It is required to operate the GRX1200+ Series receivers.
Use
• to connect from a PC to a GPS1200+ • to automatically convert data to receiver locally or remotely.
• to configure receiver operation.
• to monitor receiver operation.
•
•
RINEX format.
to automatically archive data files.
to automatically distribute to FTP locations.
• to automatically download raw data.
Operating systems
• Windows® XP • Windows® 2000
Refer to the online help of LEICA GNSS Spider for additional information.
Description of the System GPS1200+ 15
Description of the System
1.2
System Concept
1.2.1
Software Concept
GPS1200+
All receivers use the same software concept.
Description
Software type
16
Software type Description
System software
This important software covers the basic functions of the instrument. System software is also referred to as firmware.
The programs Survey and Setup are integrated into the firmware and cannot be deleted.
The English language is integrated into the firmware and cannot be deleted.
Language software
Numerous languages are available for the receivers. Language software is also referred to as system language.
The system software enables a maximum of three languages which can be stored at any one time - the English language and two other languages. The English language is the default language and cannot be deleted. One language is chosen as the active language.
Software upload
Software type Description
Application programs
Customised application programs
A suite of optional survey-specific application programs are available for the instrument.
Some of the programs are activated freely and require no license key and others require purchasing and are only activated with a license key.
Custom software specific to user requirements can be developed using the GeoC++ development kit.
Information on the GeoC++ development environment is available on request from a Leica Geosystems representative.
RX1200 software
For RX1210 and RX1210T. This software covers display, sound and communication settings of the RX1210 and RX1210T.
All instrument software is stored in the System RAM of the receiver. The software can be uploaded onto the receiver using the following methods:
• Using LGO the software is transferred via the serial interface to the Compact-
Flash card in the receiver, which is then stored to the System RAM.
• By connecting the CompactFlash card directly to the computer either via an internal card slot housing or an external OMNI drive, the software is transferred to the card, which is then stored to the System RAM.
Description of the System GPS1200+ 17
Description of the System
1.2.2
GPS1200+
Data Storage and Data Conversion Concept
Description
Memory device
)
18
Data is stored within a job in a database on a memory device. This is either a
CompactFlash card or an internal memory.
CompactFlash card:
Internal memory:
A CompactFlash card slot is standard. A CompactFlash card can be inserted and removed. Various capacities are available.
)
Whilst other CompactFlash cards may be used,
Leica recommends to only use Leica Compact-
Flash cards and is not responsible for data loss or any other error that may occur whilst using a non-Leica card.
An internal memory is optional. It resides inside the receiver. Available capacity: 256 MB or 1 GB
Unplugging connecting cables or removing the CompactFlash card during the measurement may cause loss of data. Always return to GPS1200+ Main Menu before removing the CompactFlash card and switch off the instrument before removing cables.
)
Data conversion
Transfer raw data to LGO
)
For GRX1200+ Series receivers:
While in remote operation mode, stop point occupation and ring buffer logging before removing the CompactFlash card.
Export
Data can be exported from a job in a wide range of ASCII formats. The export format is defined in Format Manager which is a PC tool in LEICA Geo Office. Refer to the online help of LGO for information on creating format files.
Data can also be exported from a job in DXF or LandXML format.
Import
Data can be imported from ASCII, DXF, GSI8 or GSI16 format.
Raw data can be transferred between the database on the CompactFlash card or the internal memory of the receiver and LGO in two ways:
• From the CompactFlash card or the internal memory directly through a serial interface to a project in LGO on a PC.
• From the CompactFlash card using for example an OMNI drive as supplied by
Leica Geosystems to a project in LGO on a PC.
CompactFlash cards can directly be used in an OMNI drive as supplied by Leica
Geosystems. Other PC card drives may require an adaptor.
GPS1200+ Description of the System 19
Description of the System
1.2.3
Power Concept
General
Power options
GPS1200+ 20
Use the Leica Geosystems batteries, chargers and accessories or accessories recommended by Leica Geosystems to ensure the correct functionality of the instrument.
Receiver
Power for the receiver can be supplied either internally or externally. Up to two external power supplies can be connected using a Y-cable. For the
GRX1200+ Series one of the two external power supplies can be configured to be the primary which is always used when available.
Internal power supply:
External power supply:
Two GEB221 batteries fit into the receiver.
GEB171 battery connected via a cable.
OR
Car battery connected via a converter cable supplied by
Leica Geosystems.
OR
10.5-28 V DC power supply via a converter cable supplied by Leica Geosystems.
OR
110/240 V AC to 12 V DC power supply unit, supplied by Leica Geosystems.
)
For permanent operations use Uninterruptible Power Supply units as a back-up in case of a main power failure.
Description of the System GPS1200+ 21
Description of the System
1.3
Container Contents
Container for
GX1200+ receivers and delivered accessories part 1 of 2 a b c d
GPS1200+ e
22
GPS12_135 f g h a) Double arm for antennas of devices b) Allen key c) GEB221 internal battery d) Supplied stylus e) Antennas of device f) GX1200+ with RX1210 and device such as radio g) Antenna and GAD31 adapter h) Cables
Container for
GX1200+ receivers and delivered accessories part 2 of 2 a b c d e f
GPS12_136 g h
Description of the System GPS1200+ i a) Base for telescopic rod b) GHT39 holder for RX1210 on pole with grip for pole c) GEB221 internal battery d) GAD33 arm 15 cm e) Telescopic rod f) Holder for GX1200+ on pole g) Tribrach h) Carrier i) Height hook
23
Description of the System
1.4
Receiver Components
GPS1200+
Receiver components
ON/OFF button
24 a d e f b c
GPS12_134 g j i h a) RX1200 b) Supplied stylus c) Clip-on-contacts for connecting
RX1200 without cable d) Recess for RX1200 e) Guide rail for clip-on-housing of a device f) ON/OFF button g) LED indicators h) Battery compartment 2 or port NET i) Battery compartment 1 j) CompactFlash card compartment
The receiver can be preprogrammed in the office and used in the field without the
RX1200 attached. In this case, the receiver is turned on by holding down the
ON/OFF button for 2 s or off by holding down the ON/OFF button for 4 s. A green steady light at the power LED indicates that the receiver is turned on.
Description of the System GPS1200+ 25
User Interface GPS1200+ 26
2
2.1
User Interface
Operating Principles
Keyboard and touch screen
The user interface is operated either by the keyboard or by the touch screen with supplied stylus. The workflow is the same for keyboard and touch screen. The difference is the way information is selected and entered.
Turn instrument on Press PROG.
Turn instrument off The instrument can only be turned off in the GPS1200+ Main Menu screen.
OR
Press both USER and PROG simultaneously.
Hold ESC for 2 s.
Lock/Unlock keyboard
Option
Lock
Description
To lock the keyboard press and hold SHIFT for 3 s. The message
’Keyboard locked’ is momentariliy displayed on the Message Line.
Option
Unlock
Description
To unlock the keyboard press and hold SHIFT for 3 s. The message
’Keyboard unlocked’ is momentariliy displayed on the Message Line.
Switching between
Leica SmartWorx software and
Windows CE desktop
This is valid for RX1250.
a b
User Interface d c
RX12_33
GPS1200+ a) Icon to start Leica
SmartWorx software b) Windows CE desktop c) Task bar d) Start button
27
User Interface GPS1200+
Access Leica SmartWorx software
IF
RX1250 is started
Windows CE desktop is active
Leica SmartWorx software is minimised
28
THEN the Leica SmartWorx software comes up automatically.
double click
OR
to display the Leica SmartWorx software.
SHIFT PROG ( ) to display the Leica SmartWorx software.
double click
OR
to maximise it.
select SmartWorx in the task bar to maximise it.
Access Windows CE desktop
IF THEN
Leica SmartWorx software is to be minimised
SHIFT MINIM (F5) in Main Menu.
Leica SmartWorx software is to be closed
SHIFT EXIT (F6) in Main Menu.
Windows CE task bar is to be displayed
SHIFT PROG ( ).
Selecting from a menu
.
Appearance
Selecting a page
Appearance
Description
To select an item from a menu, do one of the following:
Move the focus to the item. ENTER or CONT (F1)
OR
Type the complete selection number in front of the item. ENTER or CONT (F1) are not required.
OR
Tap on the item.
Description
To select a page in a screen, do one of the following:
PAGE (F6)
.
OR
Tap on the page tab.
User Interface GPS1200+ 29
User Interface
Appearance and selection from a choicelist
GPS1200+
Choicelists have various appearances.
30
.
Closed choicelist
Appearance Description Selection
Triangles on the right indicate further available choices.
Use the arrow keys to toggle through the list or tap the triangles on the screen.
ENTER or tap on the field to access the choicelist. Opening a choicelist reveals either a simple listbox or a comprehensive listbox dialogue.
.
Simple listbox
Appearance Description Selection
• Choicelist shows items to select.
• A search field is shown if necessary
• A scroll bar is shown if necessary.
• Highlight an item and
ENTER .
• To exit without changes ESC or tap outside the simple listbox.
User Interface
Listbox dialogue
.
Appearance Description Selection
• Choicelist fills the whole screen.
• A search field is shown.
• A scroll bar is shown if necessary.
• The functionality comprises adding, editing and deleting of items.
• Highlight an item and
CONT (F1) or ENTER.
• To exit without changes press ESC or tap .
• Listbox dialogues are explained in detail at appropriate places in the manuals.
GPS1200+ 31
GPS1200+ 32 User Interface
2.2
Icons
Description
)
Position of the icons on the screen
Icons show the current status information of the receiver.
The icons provide information related to basic receiver functions. The icons that appear depend upon which GPS1200+ receiver is used and the current receiver configuration.
GPS12_130 a b c d e f g h i j k a) Position status b) Number of visible satellites c) Contributing satellites d) Real-time device and real-time status, Internet online status e) Position mode f) Bluetooth g) Line/area h) CompactFlash card/internal memory i) Battery j) SHIFT k) Quick coding
Icons
User Interface
Icon
Position status
Number of visible satellites
Description
Displays the status of the current position. As soon as this icon becomes visible the receiver is in a stage where practical operation can commence.
Displays the number of theoretically visible satellites above the configured cut off angle according to the current almanac.
Contributing satellites
Real-time device and real-time status
Displays the number of satellites that are contributing to the currently computed position solution.
)
The number of contributing satellites can differ from the number of visible satellites. This may be either because satellites cannot be viewed or the observations to these satellites are considered to be too noisy to be used in the position solution.
Displays the real-time device configured to be used and its status.
Receiver is online in the Internet.
Internet online status
Position mode Displays the current position mode depending on the configuration defined.
GPS1200+ 33
User Interface
Icon
Bluetooth
Line/area
CompactFlash card/internal memory
Battery
GPS1200+ 34
Description
Symbols are added to the basic position mode icon when raw data logging or logging of auto points is configured.
The status of each Bluetooth port and any Bluetooth connection is displayed.
The number of lines and areas currently open in the active job is displayed.
The status of the CompactFlash card and internal memory are displayed.
• For the CompactFlash card, the capacity of used space is shown in seven levels.
• For the internal memory, the capacity of used memory is shown in nine levels.
The status and source of the battery is displayed. The remaining power in the battery is indicated by six levels.
For GPS1200+ receivers:
• If two internal batteries are inserted, the battery with the lower voltage is used.
User Interface
Icon
SHIFT
Quick coding
Description
• If an external power supply is connected and one or two internal batteries are inserted, then the external power is used.
• If two external power supplies are attached, then the system uses the one which is configured as the preferred power supply.
For RX1250:
• If an external power supply is connected and one internal battery is inserted, then the external power is used.
The status of the SHIFT key is displayed.
Shows the quick coding configuration. Can be used with touch screen to turn quick coding on and off.
GPS1200+ 35
Operation GPS1200+
3
3.1
Operation
Equipment Setup
)
Equipment setup step-by-step
The example given is for static operations.
Step
1.
2.
3.
4.
5.
6.
Description
Set up the tripod.
Mount and level the tribrach on the tripod.
Ensure that the tribrach is over the marker.
Place and lock the carrier in the tribrach.
Screw the antenna onto the carrier.
Check that the tribrach is still level.
7.
)
Insert the batteries into the receiver.
Alternatively or in addition, to power the receiver externally, connect a
GEB171 battery to the port PWR on the receiver. When using the sensor for real-time applications on construction machinery (machine automation), it is recommended to power the sensor externally.
36
Operation
Step Description
8.
If no internal memory is fitted, insert a CompactFlash card into the receiver.
)
A memory device must be available otherwise a survey cannot be carried
) out.
Close the lid carefully after insertion of the CompactFlash card in order to prevent water and dust from getting inside the receiver.
9.
10.
11.
To hang the receiver on the tripod leg, use the hook on the rear of the unit.
)
Alternatively place the receiver in the transport container.
12.
Insert the height hook into the carrier.
13.
Measure the antenna height using the height hook.
14.
15.
Attach the RX1200 to the receiver, if required, either directly or via a connection cable by plugging it into the port RX on the receiver.
Connect the receiver to the antenna using the antenna cable and port ANT on the receiver.
Press the ON/OFF button on the receiver for at least 2 s or PROG on the
RX1200 to switch the receiver on.
The receiver is now ready for operation.
GPS1200+ 37
GPS1200+ 38 Operation
3.2
Battery
)
Primary use/charging
• The battery must be charged prior to using it for the first time because it is delivered with an energy content as low as possible.
• For new batteries or batteries that have been stored for a long time (> three months), it is effectual to make only one charge/discharge cycle.
• For Li-Ion batteries, a single discharging and charging cycle is sufficient. We recommend carrying out the process when the battery capacity indicated on the charger or on a Leica Geosystems product deviates significantly from the actual battery capacity available.
• The permissible temperature range for charging is between 0°C to +40°C/ +32°F to +104°F. For optimal charging we recommend charging the batteries at a low ambient temperature of +10°C to +20°C/+50°F to +68°F if possible.
• It is normal for the battery to become warm during charging. Using the chargers recommended by Leica Geosystems, it is not possible to charge the battery if the temperature is too high.
Change battery step-by-step
Operation/Discharging
• The batteries can be operated from -20°C to +55°C/-4°F to +131°F.
• Low operating temperatures reduce the capacity that can be drawn; very high operating temperatures reduce the service life of the battery.
The batteries are inserted in the front of the receiver.
3
1
3
2
Operation
GPS12_085
Step
1.
2.
Description
Loosen the screw of one of the battery compartments.
Open the cover of the battery compartment.
GPS1200+ 39
Operation
Step
3.
4.
5.
6.
7.
8.
9.
10.
GPS1200+ 40
Description
With the Leica logo facing upwards, slide the battery into the battery compartment and push upwards so that it locks into position.
Close the cover of the battery compartment and tighten the screw.
Repeat steps 2. to 4. for the second battery compartment.
To remove a battery, loosen the screw to open the cover of the battery compartment.
Push the battery slightly in and at the same time downwards. This releases the battery from its fixed position.
Pull out the battery.
Close the cover of the battery compartment and tighten the screw.
Repeat steps 6. to 9. for the second battery compartment.
3.3
)
Working with the CompactFlash Card
• Keep the card dry.
• Use it only within the specified temperature range.
• Do not bend the card.
• Protect the card from direct impacts.
)
Failure to follow these instructions could result in data loss and/or permanent damage to the card.
Insert and remove a CompactFlash card step-by-step
The CompactFlash card is inserted into a slot inside of battery compartment A on the front of the receiver.
7
4
3
Operation
GPS12_086
8
1
2
A
GPS1200+
A Battery compartment A
41
Operation
7.
8.
5.
6.
9.
Step
1.
2.
3.
4.
GPS1200+ 42
Description
Loosen the screw of the battery compartment A.
Open the cover of battery compartment A.
The card should be held such that the arrow at the card is aligned with the arrow on the receiver.
Slide the card firmly into the slot until it clicks into position. To avoid damaging the card or the reader, do not use force when inserting the card.
Close the compartment cover.
To remove the card, open the cover of battery compartment A.
Press the eject button above the card slot.
Pull out the CompactFlash card.
Close the compartment cover.
Format a Compact-
Flash card step-bystep
Formatting the CompactFlash card before logging data is started is required if a completely new CompactFlash card is used or if all existing data needs to be deleted.
Step
1.
2.
Description
Select Main Menu: Tools...\Format Memory Device.
TOOLS Format Memory Device
<Memory Device: CF Card>
<Format Method: Format Quick>
)
Select the memory device to be formatted.
By activating the format command all data will be lost. Make sure that all important data on the CompactFlash card has been backed up before formatting the card. Before formatting the internal memory make sure that
) all important data is first transferred to the PC.
To exit the screen without formatting the memory device, press ESC. This returns to the previous screen.
3.
4.
CONT (F1)
YES (F4) to continue with the formatting of the selected device.
GPS1200+ Operation 43
Operation GPS1200+
Step Description
)
NO (F6) to not continue with the formatting of the selected device and to return to TOOLS Format Memory Device.
5.
Once the formatting of the card is completed the system returns to
GPS1200+ Main Menu.
44
3.4
Working with the Clip-On-Housings for Devices
Devices fitting into a clip-on-housing
Digital cellular phones fitting into a clip-on-housing
Digital cellular phone
Siemens MC75
CDMA MultiTech MTMMC-C (US)
CDMA MultiTech MTMMC-C (CAN)
Clip-on-housing
GFU24
GFU19, GFU26
GFU25
Radios fitting into a clip-on-housing
Radio
Pacific Crest PDL, receive
Satelline 3AS, transceive
Clip-on-housing
GFU15
GFU14
Operation GPS1200+ 45
Operation
Attach a clip-onhousing step-bystep
GPS1200+ 46
The clip-on-housing for devices fits on either of the small sides of the receiver.
Step
1.
2.
3.
4.
Description
Place the clip-on-housing into position such that the guide rails for the clipon-housing on the receiver and the guide rails on the clip-on-housing are aligned.
Ensure that the connector on the clip-on-housing fits to port P1 or port P3 on the receiver front panel.
Slide the clip-on-housing towards the receiver front panel until the connector is completely plugged into port P1 or port P3.
On the top side of the clip-on-housing, turn the screw clockwise, as shown by the symbols on the screw, to lock the clip-on-housing to the receiver.
Detach a clip-onhousing step-bystep
Step
1.
2.
Description
On the top side of the clip-on-housing, turn the screw anticlockwise, as shown by the symbols on the screw, to unlock the clip-on-housing from the receiver.
Slide the clip-on-housing away from the receiver front panel until the connector is completely unplugged from port P1 or port P3.
Insert a SIM card step-by-step
For those digital cellular phones that require SIM cards.
Step
1.
2.
5.
6.
3.
4.
7.
8.
9.
10.
11.
Description
Take the SIM card, a coin and a pen.
Locate the SIM card screw, that covers the SIM card slot, on the bottom of the clip-on-housing.
Insert the coin into the groove of the SIM card screw.
Turn the coin anticlockwise to loosen the SIM card screw.
Remove the SIM card screw from the housing.
Using the pen, press the small button of the SIM card slot to eject the SIM card holder.
Take the SIM card holder out off the housing.
Put the SIM card into the SIM card holder, the chip facing up.
Insert the SIM card holder into the SIM card slot, the chip facing the connectors inside the slot.
Place the SIM card screw back on the housing.
Insert the coin into the groove of the SIM card screw.
Operation GPS1200+ 47
Operation
Step
12.
GPS1200+
Description
Turn the coin clockwise to tighten the SIM card screw.
48
Remove a SIM card step-by-step
For those digital cellular phones that require SIM cards.
Operation
7
6
5
4
GPS12_088
Step
1.
2.
3.
Description
Take a coin and a pen.
Locate the SIM card screw, that covers the SIM card slot, on the bottom of the clip-on-housing.
Insert the coin into the groove of the SIM card screw.
GPS1200+ 49
Operation
Step
4.
5.
6.
7.
8.
9.
10.
11.
GPS1200+ 50
Description
Turn the coin anticlockwise to loosen the SIM card screw.
Remove the SIM card screw from the housing.
Using the pen, press the small button of the SIM card slot to eject the SIM card holder.
Take the SIM card holder out off the SIM card slot.
Take the SIM card out of the SIM card holder.
Put the SIM card holder back into the SIM card slot, the even side not facing the contacts inside the slot.
Place the SIM card screw back on the housing.
Turn the coin clockwise to tighten the SIM card screw.
LED indicators Description
Each clip-on-housing for a radio, digital cellular phones or bluetooth communication has Light Emitting Diode indicators on the bottom side. They indicate the basic device status.
Diagram
Operation
GPS12_089 a b c d
GPS1200+ a) Warning LED, available for Satelline 3AS b) Data transfer LED c) Signal strength LED d) Power LED
51
Operation GPS1200+ 52
Description of the LED’s
IF the
Warning
LED
Data transfer
LED
Signal strength
LED on
GFU14 with
Satelline 3AS is red any device off green or flashing green
GFU19 (US),
GFU25 (CAN),
GFU26 (US) with CDMA
MultiTech
MTMMC-C red flashing red off
THEN the device is in the configuration mode controlled from the PC via cable.
data is not being transferred.
data is being transferred.
device is on, not registered on the network.
device is on, registered on the network.
download mode or device is off.
Operation
IF the on is THEN
GFU24 with
Siemens MC75 red red: long flash, long break call is in progress.
no SIM card inserted, no PIN entered or network search, user authentication or network login in progress.
GFU15 with
Pacific Crest
PDL red: short flash, long break red: flashing red, long break red: long flash, short break off logged onto network, no call in progress.
GPRS PDP context activated.
Packet switched data transfer is in progress.
device is off.
red or flashing red the communication link, Data
C arrier Detection, is okay on the roving receiver.
off the DCD is not okay.
GPS1200+ 53
Operation
IF the
Power
LED
GPS1200+ 54 on
GFU14 with
Satelline 3AS any device is THEN red or flashing red the communication link, Data
C arrier Detection, is okay on the roving receiver.
off off green the DCD is not okay.
power is off.
power is okay.
3.5
Access
Accessing Survey Application Program
OR
Select Main Menu: Survey.
Press PROG. Highlight Survey. CONT (F1).
SURVEY
Survey Begin
CONT (F1)
To accept changes and access the subsequent screen. The chosen settings become active.
CONF (F2)
Available for <R-Time Mode: None> and <R-Time Mode: Rover>. To configure auto points and hidden point measurements.
Operation GPS1200+ 55
Operation
Description of fields
Field
<Job:>
Option
Choicelist
<Coord
System:>
Output
<Codelist:>
GPS1200+ 56
CSYS (F6)
To select a different coordinate system. Not available for <Use Auto
CrdSys: Yes> configured in
CONFIGURE Additional Rover
Settings .
Choicelist
Description
The active job. All jobs from Main Menu:
Manage...\Jobs can be selected.
The coordinate system currently attached to the selected <Job:>. Cannot be edited for <Use
AutoCrdSys: Yes>
configured in CONFIGURE
Additional Rover Settings .
No codes are stored in the selected <Job:>. All codelists from Main Menu:
Manage...\Codelists can be selected.
Operation
Field
<Config
Set:>
<Antenna:>
Option
Output
Choicelist
Choicelist
GPS1200+
Description
Codes have already been stored in the selected
<Job:> . If codes had been copied from a
System RAM codelist, then the name of the codelist is displayed. If codes have not been copied from a System RAM codelist but typed in manually, then the name of the active job is displayed.
The active configuration set. All configuration sets from Main Menu: Manage...\Configura- tion Sets can be selected.
The receiver has numerous user configurable parameters and functions. This allows a variety of preferences to be addressed. The configuration of the parameters and functions for an individual measuring technique are combined in a configuration set.
The antenna currently defined to be used in the selected configuration set. All antennas from
Main Menu: Manage...\Antennas
can be selected.
57
Operation GPS1200+ 58
Next step
CONT (F1) accepts the changes and accesses, depending on the selected <Config
Set:> , SURVEY Survey: Job Name or SURVEY Survey Set Up Reference
Station . Measurements can be performed with OCUPY (F1), STOP (F1) and
STORE (F1).
3.6
Guidelines for Correct Results
Undisturbed satellite signal reception
Successful GNSS surveys require undisturbed satellite signal reception, especially at the receiver which serves as a reference. Set up the receivers in locations which are free of obstructions such as trees, buildings or mountains.
Steady antenna for static surveys
For static surveys, the antenna must be kept perfectly steady throughout the whole occupation of a point. Put the antenna on a tripod or pillar.
Centred and levelled antenna
Centre and level the antenna precisely over the marker.
Operation GPS1200+ 59
Operation
3.7
GPS1200+
Operation with a Typical Configuration Set
)
Static operations step-by-step
The example given is for static operations.
Step Description
1.
)
Set up the equipment.
Always fill out a field record sheet for each point.
)
It is vital that the antenna height is measured correctly. Measure the height at the beginning and at the end of the occupation.
)
The Satellite Settings of the GX1230+ GNSS accomodates three additional fields: <GLONASS:> (selection Yes or No), <Galileo:> (selection
Yes
or No) and <GPS L5:> (selection Yes or No).
2.
3.
Start the Survey application program.
SURVEY Survey Begin
<Job: Default>
<Coord System: WGS 1984>
<Codelist: <None>>
<Config Set:>
Select a configuration set for static operations.
60
Operation
Step Description
4.
5.
<Antenna: AX1203+ GNSS>
CONT (F1)
SURVEY Survey: Job Name
)
Type in the point ID and the antenna height.
The position mode icon is the moving icon. This indicates that the antenna can be moved around and that no static observations are being recorded.
6.
)
OCUPY (F1) starts logging of static observations.
The position mode icon changes to the static icon indicating that the receiver should remain stationary. For a static survey, the GPS antenna has to be kept totally still.
7.
If required, check information, for example on the satellites, the memory
) or the battery.
SHIFT QUIT (F6) always terminates the survey operation, even during a site occupation. In this case all data collected since pressing OCUPY (F1) is lost.
8.
9.
STOP
(F1) when enough data is collected.
STORE (F1) to store the point information.
GPS1200+ 61
Operation GPS1200+
Step
10.
Description
Check that the tribrach is still level and note it down in the field record sheet.
11.
)
Measure the antenna height and note it down in the field record sheet.
If the tribrach is not level or the antenna height has changed, the collected data is not reliable.
12.
13.
14.
15.
16.
17.
18.
SHIFT QUIT (F6) to return to from where SURVEY Survey: Job Name was accessed.
ESC until in GPS1200+ Main Menu.
GPS1200+ Main Menu
PROG plus USER to turn off the receiver.
Take down the equipment and put it back into the transport container.
Are more points to be surveyed?
•
If yes, continue with step 17.
•
Move to the next point.
62
)
)
Step
19.
Description
Post-process the data in the office.
The antenna must not be moved while data is logged, otherwise the quality of postprocessed coordinates is impaired.
The CompactFlash card must be removed in GPS1200+ Main Menu. If the card is removed when in any other screen all stored data might get corrupted, preventing
LGO from successfully reading the data on the card.
Operation GPS1200+ 63
Reference Station GPS1200+ 64
4
4.1
Description
Reference Station
Overview
The GRX1200+ Series
• are designed to operate for specific reference station applications using remote control software, for example LEICA GNSS Spider reference station software.
• support internal logging of raw observations which can be downloaded using an external remote control software package such as LEICA GNSS Spider.
• support streaming output of GPS and GLONASS raw observations and status information.
• can log or stream out data from specific external devices approved by Leica
Geosystems, such as meteo and tilt, which can be directly output to an external remote control software package.
• can be used to transmit data for real-time operations in proprietary as well as standard RTCM, CMR and CMR+ formats, using a variety of communication devices, including suitable radios, digital cellular phones or modems. The
GRX1200+ Series cannot receive reference station broadcasts and therefore cannot be used as a real-time rover receiver.
• can be configured via a web interface.
Special features
• can send out Event E-mails and push Raw data to an FTP server.
• can log data to MDB, RINEX and compact RINEX files.
• have the same receiver and measurement performance as the other GPS1200+
receivers. Refer to "7 Technical Data" for information on technical data.
To operate for specific reference station applications, the GRX1200+ Series is, compared with the other GPS1200+ receivers, equipped with some special features.
Specific to the GRX1200+ Series: • Controllable dual external power supply
• Support of external devices such as meteo and tilt
Additional features for GRX1200+ and
GRX1200+ GNSS: • Ring buffer logging
• Web interface
• Event E-mail
• FTP server/push
• RINEX logging
• DynDNS
• High frequency SNR logging
• RTK multiplexing
Reference Station GPS1200+ 65
Reference Station GPS1200+ 66
• One Ethernet port including three logical NET ports
• One port to output PPS
• One port to input event messages
• One port for input from an external oscillator
Additional features for GRX1200+ GNSS: • Tracking of GLONASS observables
• Tracking of GPS L5 observables
• Tracking of Galileo observables
Data storage
Data streaming
Power supply
All CompactFlash cards recommended by Leica Geosystems are supported. Storing data on a CompactFlash card enables subsequent data download and post-
processing. Refer to "1.2.2 Data Storage and Data Conversion Concept" for infor-
mation on available memory. Refer to "3.3 Working with the CompactFlash Card" for
information on inserting and removing a CompactFlash card.
The receiver can be set to stream the raw observations or RTK corrections out of two different communication ports instead of or in addition to storing data on the
CompactFlash card.
Refer to "1.2.3 Power Concept".
Commands for remote control
Special commands from Outside World Interface or Leica Binary 2 format can be used to control the receiver. Documentation for OWI and LB2 is available on request from the Leica Geosystems representative.
Reference Station GPS1200+ 67
Reference Station
4.2
Equipment Setup
Equipment setup
GPS1200+ 68
An example for an equipment setup for a reference station is shown in the following diagram. It is a basic serial setup with LEICA GNSS Spider, including a meteo/tilt device and a local radio to broadcast real-time data.
Reference Station c d e a b f g h i
GPS12_027 j k l m n o
GPS1200+ p r q t s
69
Reference Station GPS1200+ 70 a) Network hub or router for Internet connection b) Power supply unit 100/240 V AC to
12 V DC k) Surge arrester l) CompactFlash card c) Interface cable d) DB9 surge arrester with 12 V DC pass through m) Radio interface cable n) Radio e) Meteo/tilt device with interface cable o) Cable to connect radio antenna f) Receiver GRX1200+ Series p) PC for running LEICA GNSS Spider software or the web interface g) Weather protection radome for
AT504 GG/AR25 h) AT504 GG/AR25 i) AX1203+ GNSS j) TNC to TNC antenna cable q) Ethernet cable for data transfer and receiver communication r) Ethernet port s) Radio antenna t) Radio surge arrester
)
)
A ruggedized ethernet cable is used to connect the GRX1200+ Series to the internet. Any PC connected to the internet can then be used to configure the sensor.
The data transfer cable GX RX to RS232 or an ethernet crossover cable can be used to connect the GRX1200+ Series directly to a PC.
)
)
Cable connection
Switch on
Switch off
Connect the device to transmit real-time data to port P1, P2 or P3 of the receiver.
Some devices fit into a clip-on-housing that plugs directly into these ports. Other devices require an interface cable.
Unauthorised radio units should not be connected to the GRX1200+ Series.
Cable connections are identical to other GPS1200+ receivers. Additional cables are available from Leica Geosystems for the specific oscillator and Ethernet ports on the
GRX1200+.
Hold down the ON/OFF button on the receiver for at least 2 s.
OR
Press PROG on the RX1200, if used.
OR
Send a pulse/data to one of the serial ports. Port P1, P2 and P3 can be configured not to allow receiver switch on upon pulse reception.
Press the ON/OFF button on the receiver for at least 4 s.
OR
Press PROG and USER simultaneously on the RX1200, if used.
OR
GPS1200+ Reference Station 71
Reference Station
Behaviour when turning off and on
Behaviour after power failure
GPS1200+
Click on POWER DOWN in the Web Interface Tools menu.
72
Turning the GRX1200+ Series off and on again resets the receiver. The consequences are:
• If the configuration of the output is stored in the configuration set, standard
NMEA messages are still output.
• All data/message outputs scheduled via OWI or LB2 commands are no longer output.
• Data logging parameters and interface configuration options, that have been set by OWI or LB2 commands and have not been saved to a configuration set using the corresponding OWI or LB2 command, are reset.
After temporary power failure, the GRX1200+ Series will automatically power itself up and resume the previously set operations including OWI or LB2 output. Two power fail recovery options are available - Sudden Loss Only and Always. To access the configuration select either:
• RX1200: Main Menu: Config...\General Settings...\Start Up & Power Down.
• Computer: Configuration - Start Up & Power Down in the web interface.
4.3
)
Getting Started with the GRX1200+ Series
Refer to the seperate "GRX1200+ Series - Getting Started" manual for more detailed information.
Ways of operating The GRX1200+ Series can either be operated with the RX1200 like the other
GPS1200+ receivers or by remote control, with its web interface or a reference station software.
Operation
With RX1200
Description
The receiver can be fully configured and point occupation can be started/stopped when using the campaign option.
Available with full functionality
• Job management
• Data management
• Configuration of ports
• Configuration of operation parameters
• Status information
• Transfer capabilities including the upload of new firmware
GPS1200+ Reference Station 73
Reference Station
Operation
By remote control
GPS1200+
Description
)
With the purchased campaign option, starting and stopping point occupation for raw data logging can be done from the RX1200.
Unavailable
Any other application program available on GPS1200+ such as
Stakeout
)
Refer to the relevant chapters in this manual or to the
GPS1200+ Technical Reference Manual for information on configuring and using the receiver.
• Special commands from OWI or LB2 can be used to control the GRX1200+ Series through a remote interface.
• For the majority of applications, the GRX1200+ Series has to be operated using a suitable application software that supports the OWI or LB2 commands, such as LEICA GNSS
Spider.
• Remote control also supports the download of internally logged data and upload of files to the receiver.
74
Operation Description
By web interface • For the GRX1200+ Series a web server is included in the receiver that allows remote control from any computer via
TCP/IP or internet interface connection and web browser.
Reference Station GPS1200+ 75
Reference Station GPS1200+ 76
Configure a remote interface connection
Remote interface to be configured Configure using
Standard default RS232 • Each port is by default a remote port.
No specific receiver configurations must be done.
• The default settings allow immediate communication using the following port communication parameters:
Baud rate: 115200
Data bits: 8
Parity: None
Stop bit: 1
Flow control: None
Specific devices such as modems for a particular port
Must be configured using the RX1200.
Refer to "Configure a modem interface step-by-step" for an example.
GRX1200+ built-in ethernet device for communicating with the receiver
Must be configured using the RX1200 or the
Startup Configurator. Refer to "Configure a
NET port step-by-step" for an example.
Remote interface to be configured Configure using
Any other interface and operation configuration required
Can be done using LEICA GNSS Spider or the web interface.
Configure a modem interface step-by-step
In order to use a modem for the remote interface connection, the corresponding device has to be created on the receiver and attached to the receiver serial port. As an example, the following step-by-step description shows how to configure a U.S.
Robotics 56k modem for port P1 on the receiver. Refer to the GPS1200+ Technical
Reference Manual for more information. Refer to the manual of the modem for information on the modem configuration.
Step
1.
2.
Description
Main Menu: Config...\Interfaces...
CONFIGURE Interfaces
Highlight Remote.
EDIT (F3) to access CONFIGURE Remote Interfaces.
3.
4.
)
Highlight 1.
Remote
must be displayed in column Interface. USE (F6) and YES (F6) to close other interfaces configured on this port.
GPS1200+ Reference Station 77
Reference Station GPS1200+
Step
5.
6.
7.
Description
DEVCE (F5) to access CONFIGURE Devices.
PAGE (F6) changes to the Modem/GSM page.
CONFIGURE Devices , Modem/GSM page
Highlight Modem.
NEW (F2) to create a new modem.
8.
9.
12.
CONFIGURE Device
Type in a name and the port parameters for the modem.
)
ATCMD (F4) to configure the communication commands for the modem.
10.
STORE (F1) to return to CONFIGURE Devices, Modem/GSM page.
)
The receiver is ready to accept an incoming call from a remote application.
11.
Connect the modem to port P1 of the receiver using a modem cable.
Connect the modem cable to the phone line and to a suitable power supply.
78
Configure a NET port step-by-step
In order to use a NET port for the remote interface connection, the RJ45 connector of the GRX1200+/GRX1200+ GNSS must be connected to a network hub or router.
If connecting directly to a PC, a crossed Ethernet cable is required. The following step-by-step description shows how to configure a NET port and assign the remote interface to it. Refer to the GPS1200+ Technical Reference Manual and to the
"GRX1200+ Series - Getting Started" for more information.
Step
1.
2.
3.
4.
5.
6.
7.
8.
Description
Main Menu: Config...\Instrument Settings...\Set NET Parameters
CONFIGURE Set NET Parameters
Enter the Internet Protocol address, the network mask and the gateway.
CONT (F1) returns to GPS1200+ Main Menu.
Main Menu: Config...\Interfaces...
CONFIGURE Interfaces
Highlight Remote.
EDIT (F3) to access CONFIGURE Remote Interfaces.
Highlight a NET port.
CTRL (F4) to access CONFIGURE Set NET Port.
Reference Station GPS1200+ 79
Reference Station GPS1200+
Step
9.
Description
CONFIGURE Set NET Port
10.
11.
<User: Server>
Configure the NET port number and access control.
CONT (F1) to return to CONFIGURE Remote Interfaces.
Is Remote displayed in the column Interface for the selected NET port?
•
If yes, continue with step 13.
•
USE (F6) and YES (F6) to close other interfaces configured on this port.
12.
13.
Press CONT (F1) twice to return to GPS1200+ Main Menu.
)
The receiver is ready to accept an incoming call from a remote application.
14.
Connect the receivers RJ45 connector NET to a LAN using a suitable network cable.
80
Reference Station GPS1200+ 81
Care and Transport GPS1200+ 82
5
5.1
Care and Transport
Transport
Transport in the field
When transporting the equipment in the field, always make sure that you
• either carry the product in its original transport container,
• or carry the tripod with its legs splayed across your shoulder, keeping the attached product upright.
Transport in a road vehicle
Never carry the product loose in a road vehicle, as it can be affected by shock and vibration. Always carry the product in its transport container and secure it.
Shipping When transporting the product by rail, air or sea, always use the complete original
Leica Geosystems packaging, transport container and cardboard box, or its equivalent, to protect against shock and vibration.
Shipping, transport of batteries
When transporting or shipping batteries, the person in charge of the product must ensure that the applicable national and international rules and regulations are observed. Before transportation or shipping, contact your local passenger or freight transport company.
5.2
Product
Storage
Li-Ion batteries
Respect the temperature limits when storing the equipment, particularly in summer
if the equipment is inside a vehicle. Refer to "7 Technical Data" for information about
temperature limits.
•
Refer to "7.1.3 Technical Data" for information about storage temperature range.
• A storage temperature range of -20 to +30°C/-4 to 86°F in a dry environment is recommended to minimise self-discharging of the battery.
• At the recommended storage temperature range, batteries containing a 10% to
50% charge can be stored for up to one year. After this storage period the batteries must be recharged.
• Remove batteries from the product and the charger before storing.
• After storage recharge batteries before using.
• Protect batteries from damp and wetness. Wet or damp batteries must be dried before storing or use.
Care and Transport GPS1200+ 83
Care and Transport
5.3
Cleaning and Drying
GPS1200+ 84
Product and accessories
Use only a clean, soft, lint-free cloth for cleaning. If necessary, moisten the cloth with water or pure alcohol.
Do not use other liquids; these may attack the polymer components.
Damp products Dry the product, the transport container, the foam inserts and the accessories at a temperature not greater than 40°C/104°F and clean them. Do not repack until everything is completely dry. Always close the transport container when using in the field.
Cables and plugs Keep plugs clean and dry. Blow away any dirt lodged in the plugs of the connecting cables.
Connectors with dust caps
Wet connectors must be completely dry before attaching the dust cap.
Care and Transport GPS1200+ 85
Safety Directions GPS1200+ 86
6
6.1
Description
Safety Directions
General Introduction
The following directions should enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid operational hazards.
The person responsible for the product must ensure that all users understand these directions and adhere to them.
6.2
Intended Use
Permitted use
Adverse use
Safety Directions
• Measuring raw data and computing coordinates using carrier phase and code signal from GNSS satellites.
• Carrying out measurement tasks using various GNSS measuring techniques.
• Recording GNSS and point related data.
• Computing by means of software.
• Data communcation with external appliances.
• Use of the product without instruction.
• Use outside of the intended limits.
• Disabling safety systems.
• Removal of hazard notices.
• Opening the product using tools, for example screwdriver, unless this is specifically permitted for certain functions.
• Modification or conversion of the product.
• Use after misappropriation.
• Use of products with obviously recognizable damages or defects.
• Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems.
GPS1200+ 87
Safety Directions
Warning
GPS1200+ 88
• Inadequate safeguards at the working site, for example when measuring on roads.
• Controlling of machines, moving objects or similar monitoring application without additional control- and safety installations.
Adverse use can lead to injury, malfunction and damage.
It is the task of the person responsible for the equipment to inform the user about hazards and how to counteract them. The product is not to be operated until the user has been instructed on how to work with it.
6.3
Danger
Limits of Use
Environment
Suitable for use in an atmosphere appropriate for permanent human habitation: not suitable for use in aggressive or explosive environments.
Local safety authorities and safety experts must be contacted before working in hazardous areas, or in close proximity to electrical installations or similar situations by the person in charge of the product.
Safety Directions GPS1200+ 89
Safety Directions
6.4
Responsibilities
GPS1200+ 90
Manufacturer of the product
Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica
Geosystems, is responsible for supplying the product, including the user manual and original accessories, in a completely safe condition.
Manufacturers of non Leica Geosystems accessories
The manufacturers of non Leica Geosystems accessories for the product are responsible for developing, implementing and communicating safety concepts for their products, and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product.
Person in charge of the product
The person in charge of the product has the following duties:
• To understand the safety instructions on the product and the instructions in the user manual.
• To be familiar with local regulations relating to safety and accident prevention.
• To inform Leica Geosystems immediately if the product and the application becomes unsafe.
Warning The person responsible for the product must ensure that it is used in accordance with the instructions. This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use.
6.5
Warning
Hazards of Use
Caution
The absence of instruction, or the inadequate imparting of instruction, can lead to incorrect or adverse use, and can give rise to accidents with far-reaching human, material, financial and environmental consequences.
Precautions:
All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product.
Watch out for erroneous measurement results if the product has been dropped or has been misused, modified, stored for long periods or transported.
Precautions:
Periodically carry out test measurements and perform the field adjustments indicated in the user manual, particularly after the product has been subjected to abnormal use and before and after important measurements.
Safety Directions GPS1200+ 91
Safety Directions
Danger
GPS1200+ 92
Because of the risk of electrocution, it is very dangerous to use poles and extensions in the vicinity of electrical installations such as power cables or electrical railways.
Precautions:
Keep at a safe distance from electrical installations. If it is essential to work in this environment, first contact the safety authorities responsible for the electrical installations and follow their instructions.
Warning
Warning
If the product is used with accessories, for example masts, staffs, poles, you may increase the risk of being struck by lightning.
Precautions:
Do not use the product in a thunderstorm.
During dynamic applications, for example stakeout procedures there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around, for example obstacles, excavations or traffic.
Precautions:
The person responsible for the product must make all users fully aware of the existing dangers.
Warning
Warning
Warning
Caution
Safety Directions
Inadequate securing of the working site can lead to dangerous situations, for example in traffic, on building sites, and at industrial installations.
Precautions:
Always ensure that the working site is adequately secured. Adhere to the regulations governing safety and accident prevention and road traffic.
Only Leica Geosystems authorised service workshops are entitled to repair these products.
If computers intended for use indoors are used in the field there is a danger of electric shock.
Precautions:
Adhere to the instructions given by the computer manufacturer with regard to field use in conjunction with Leica Geosystems products.
If the accessories used with the product are not properly secured and the product is subjected to mechanical shock, for example blows or falling, the product may be damaged or people may sustain injury.
Precautions:
When setting-up the product, make sure that the accessories are correctly adapted, fitted, secured, and locked in position.
GPS1200+ 93
Safety Directions
Caution
Caution
Warning
GPS1200+
Avoid subjecting the product to mechanical stress.
94
The product uses the GPS P-Code signal which by U.S. policy may be switched off without notice.
During the transport, shipping or disposal of batteries it is possible for inappropriate mechanical influences to constitute a fire hazard.
Precautions:
Before shipping the product or disposing of it, discharge the batteries by running the product until they are flat.
When transporting or shipping batteries, the person in charge of the product must ensure that the applicable national and international rules and regulations are observed. Before transportation or shipping contact your local passenger or freight transport company.
Using a battery charger not recommended by Leica Geosystems can destroy the batteries. This can cause fire or explosions.
Precautions:
Only use chargers recommended by Leica Geosystems to charge the batteries.
Warning
Warning
Warning
High mechanical stress, high ambient temperatures or immersion into fluids can cause leackage, fire or explosions of the batteries.
Precautions:
Protect the batteries from mechanical influences and high ambient temperatures. Do not drop or immerse batteries into fluids.
Short circuited battery terminals can overheat and cause injury or fire, for example by storing or transporting in pockets if battery terminals come in contact with jewellery, keys, metallized paper or other metals.
Precautions:
Make sure that the battery terminals do not come into contact with metallic objects.
Incorrect fastening of the external antenna to vehicles or transporters poses the risk of the equipment being broken by mechanical influence, vibration or airstream. This may result in accident and physical injury.
Precautions:
Attach the external antenna professionally. The external antenna must be secured additionally, for example by use of a safety cord. Ensure that the mounting device is correctly mounted and able to safely carry the weight of the external antenna
(>1 kg).
Safety Directions GPS1200+ 95
Safety Directions
Warning
Danger
GPS1200+ 96
If the product is improperly disposed of, the following can happen:
• If polymer parts are burnt, poisonous gases are produced which may impair health.
• If batteries are damaged or are heated strongly, they can explode and cause poisoning, burning, corrosion or environmental contamination.
• By disposing of the product irresponsibly you may enable unauthorized persons to use it in contravention of the regulations, exposing themselves and third parties to the risk of severe injury and rendering the environment liable to contamination.
Precautions:
The product must not be disposed with household waste.
Dispose of the product appropriately in accordance with the national regulations in force in your country.
Always prevent access to the product by unauthorized personnel.
Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http://www.leica-geosystems.com/treatment or received from your Leica Geosystems dealer.
If the product is used with accessories, for example on masts, staffs, poles, you may increase the risk of being struck by lightning. Danger from high voltages also exists
Safety Directions near power lines. Lightning, voltage peaks, or the touching of power lines can cause damage, injury and death.
Precautions:
• Do not use the product in a thunderstorm as you may increase the risk of being struck by lightning.
• Be sure to remain at a safe distance from electrical installations. Do not use the product directly under or in close proximity to power lines. If it is essential to work in such an environment contact the safety authorities responsible for electrical installations and follow their instructions.
• If the product has to be permanently mounted in an exposed location, it is advisable to provide a lightning conductor system. A suggestion on how to design a lightning conductor for the product is given below. Always follow the regulations in force in your country with regard to grounding antennas and masts. These installations must be carried out by an authorised specialist.
• To prevent damages due to indirect lightning strikes (voltage spikes) cables, for example for antenna, power source or modem should be protected with appropriate protection elements, like a lightning arrester. These installations must be carried out by an authorized specialist.
• If there is a risk of a thunderstorm, or if the equipment is to remain unused and unattended for a long period, protect your product additionally by unplugging all systems components and disconnecting all connecting cables and supply cables, for example, receiver - antenna.
GPS1200+ 97
Safety Directions GPS1200+ 98
Lightning conductors
Suggestion for design of a lightning conductor for a GNSS system:
1. On non-metallic structures
Protection by air terminals is recommended. An air terminal is a pointed solid or tubular rod of conducting material with proper mounting and connection to a conductor. The position of four air terminals should be uniformly distributed around the antenna at a distance equal to the height of the air terminal.
The air terminal diameter should be 12 mm for copper or 15 mm for aluminium.
The height of the air terminals should be 25 cm to 50 cm. All air terminals should be connected to the down conductors. The diameter of the air terminal should be kept to a minimum to reduce GNSS signal shading.
2. On metallic structures
Protection is as described for non-metallic structures, but the air terminals can be connected directly to the conducting structure without the need for down conductors.
Air terminal arrangement, plan view
GPS12_059 a b c a) Antenna b) Support structure c) Air terminal
Safety Directions GPS1200+ 99
Safety Directions
Grounding the receiver/antenna
GPS12_060
GPS1200+ a b c d e a) Antenna b) Lightning conductor array c) Antenna/receiver connection d) Metallic mast e) Connection to earth
100
6.6
Description
Electromagnetic Compatibility EMC
Warning
Caution
The term Electromagnetic Compatibility is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present, and without causing electromagnetic disturbances to other equipment.
Electromagnetic radiation can cause disturbances in other equipment.
Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that other equipment may be disturbed.
There is a risk that disturbances may be caused in other equipment if the product is used in conjunction with accessories from other manufacturers, for example field computers, personal computers, two-way radios, non-standard cables or external batteries.
Precautions:
Use only the equipment and accessories recommended by Leica Geosystems.
When combined with the product, they meet the strict requirements stipulated by the guidelines and standards. When using computers and two-way radios, pay attention to the information about electromagnetic compatibility provided by the manufacturer.
Safety Directions GPS1200+ 101
Safety Directions
Caution
Warning
GPS1200+ 102
Disturbances caused by electromagnetic radiation can result in erroneous measurements.
Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that the product may be disturbed by very intense electromagnetic radiation, for example, near radio transmitters, two-way radios or diesel generators.
Precautions:
Check the plausibility of results obtained under these conditions.
If the product is operated with connecting cables attached at only one of their two ends, for example external supply cables, interface cables, the permitted level of electromagnetic radiation may be exceeded and the correct functioning of other products may be impaired.
Precautions:
While the product is in use, connecting cables, for example product to external battery, product to computer, must be connected at both ends.
Radios, digital cellular phones or
ATX1230+ GNSS with Bluetooth
Warning
Use of product with radio, digital cellular phone devices or ATX1230+ GNSS with
Bluetooth:
Electromagnetic radiation can cause disturbances in other equipment, in installations, in medical devices, for example pacemakers or hearing aids and in aircraft. It can also affect humans and animals.
Precautions:
Although the product meets in combination with radio or digital cellular phone devices recommended by Leica Geosystems the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that other equipment may be disturbed or that humans or animals may be affected.
• Do not operate the product with radio or digital cellular phone devices in the vicinity of filling stations or chemical installations, or in other areas where an explosion hazard exists.
• Do not operate the product with radio or digital cellular phone devices near to medical equipment.
• Do not operate the product with radio or digital cellular phone devices in aircraft.
• Do not operate the product with radio or digital cellular phone devices for long periods immediately next to your body.
Safety Directions GPS1200+ 103
Safety Directions
6.7
GPS1200+
FCC Statement, Applicable in U.S.
Applicability
Warning
104
The grayed paragraph below is only applicable for products of the GPS1200+
System without radio, digital cellular phone devices or Bluetooth.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning
Labelling
GPS1200+
Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user's authority to operate the equipment.
Type: GX... ..............
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPS12_101
Safety Directions GPS1200+ 105
Safety Directions
Labelling RX1210
GPS1200+
Type: RX1210 .......
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including i nterference that may cause undesired operation.
RX12_023
Labelling RX1250X/
RX1250Xc Type: RX1250
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
This device complies with part
15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RX12_025
106
Labelling GFU24
Type: GFUXX . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
GPS12_103
Safety Directions GPS1200+ 107
Safety Directions
Labelling GFU19,
GFU25, GFU26
GPS1200+
Type: GFUXX . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
TPS12_218
108
Labelling internal battery GEB211,
GEB221
.............................................
....
..........
......................
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
TPS12_082
Safety Directions GPS1200+ 109
Technical Data GPS1200+ 110
7
7.1
7.1.1
Technical Data
Receiver Technical Data
Tracking Characteristics of the Receiver
Receiver technology
SmartTrack+/SmartTrack
Satellite reception GX1230+ GNSS/GX1220+ GNSS/
GRX1200+ GNSS:
GX1230+/GX1220+/GRX1200+:
GX1210+:
Triple frequency
Dual frequency
Single frequency
Receiver channels GX1230+ GNSS/GX1220+ GNSS/
GRX1200+ GNSS:
GX1230+/GX1220+/GRX1200+:
Up to 16 channels continuous tracking on L1,
L2 and L5 (GPS); up to 14 channels continuous tracking on L1 and L2 (GLONASS); up to 14 channels continuous tracking on E1,
E5a, E5b and Alt-BOC (Galileo); four channels tracking SBAS.
16 channels continuous tracking on L1 and
L2 (GPS); four channels tracking SBAS.
)
Supported codes and phases
GX1210+: 16 channels continuous tracking on L1
(GPS); four channels tracking SBAS.
Depending on the satellite systems and signals configured in CONFIGURE Satellite
Settings a maximum number of 120 channels is allocated.
GPS
Type
GX1230+ GNSS/
GX1220+ GNSS/
GRX1200+ GNSS
GX1230+/GX1220+/
GRX1200+
L1
Carrier phase,
C/A code
Carrier phase,
C/A code
GX1210+ Carrier phase,
C/A code
GLONASS
Type L1
ATX1230+ GNSS Carrier phase, C/A code
L2 L5
Carrier phase, C code (L2C) and
P2 code
Carrier phase, code
Carrier phase, C code (L2C) and
P2 code
-
-
L2
Carrier phase, P2 code
GPS1200+ Technical Data 111
Technical Data
)
Satellites tracked
GPS1200+ 112
Galileo
Type
ATX1230+ GNSS
E1
Carrier phase, code
E5a
Carrier phase, code
E5b
Carrier phase, code
Alt-BOC
Carrier phase, code
Carrier phase and code measurements on L1, L2 and L5 (GPS) are fully independent with AS on or off.
GX1230+ GNSS/GX1220+ GNSS/
GRX1200+ GNSS:
GX1230+/GX1220+/GRX1200+:
GX1210+:
Up to 16 simultaneously on L1, L2 and L5
(GPS) + up to 14 simultaneously on L1 and
L2 (GLONASS) + up to 14 simultaneously on
E1, E5a, E5b and Alt-BOC (Galileo) + up to four SBAS
Up to 16 simultaneously on L1 and L2 (GPS)
+ up to four SBAS
Up to 16 simultaneously on L1 (GPS) + up to four SBAS
7.1.2
)
Accuracy
Differential code
Accuracy is dependent upon various factors including the number of satellites tracked, constellation geometry, observation time, ephemeris accuracy, ionospheric disturbance, multipath and resolved ambiguities.
The following accuracies, given as root mean square, are based on measurements processed using LGO and on real-time measurements.
The use of multiple GNSS systems can increase accuracy by up to 30% relative to
GPS only.
For all receivers, the baseline precision of a differential code solution for static and kinematic surveys is 25 cm.
GPS1200+ Technical Data 113
Technical Data GPS1200+
Differential phase in post-processing
Normal baselines with
GX1230+ GNSS/GX1230+/GX1220+ GNSS/GX1220+/GRX1200+ Series plus
AX1203+ GNSS
Static
Horizontal
5 mm + 0.5 ppm
Vertical
Kinematic
Horizontal
10 mm + 0.5 ppm 10 mm + 1 ppm
Vertical
20 mm + 1 ppm
114
Long baselines with
GX1230+ GNSS/GX1230+/GX1220+ GNSS/GX1220+/GRX1200+ Series plus
AT504 GG/AR25
Static
Horizontal
3 mm + 0.5 ppm
Vertical
6 mm + 0.5 ppm
Short baselines with GX1210+ plus AX1201
Static
Horizontal
5 mm + 0.5 ppm
Vertical
10 mm + 0.5 ppm
Differential phase in real-time
GX1230+ GNSS/GX1230+ plus AX1203+ GNSS
Static
Horizontal
5 mm + 0.5 ppm
Vertical
Kinematic
Horizontal
10 mm + 0.5 ppm 10 mm + 1 ppm
Vertical
20 mm + 1 ppm
Technical Data GPS1200+ 115
Technical Data
7.1.3
Technical Data
Dimensions
GPS1200+
The dimensions are given for the housing without the sockets.
Type
All receivers
Length [m]
0.212
Width [m]
0.166
Weight
Recording
116
Thickness [m]
0.079
Receiver weights without battery and radio:
Type Weight [kg]
GX1230+ GNSS/GX1230+/GX1220+ GNSS/GX1220+/GX1210+ 1.2
GRX1200+/GRX1200+ GNSS 1.3
Data can be recorded on the CompactFlash card or in the internal memory, if fitted.
Technical Data
Type
CompactFlash card
Internal memory
Capacity [MB] Data capacity
•
•
•
256
1024
256
256 MB is typically sufficient for about
GPS only (12 satellites)
• 2000 h L1 + L2 + L5 data logging at 15 s rate
• 8000 h L1 + L2 + L5 data logging at 60 s rate
• 360000 real-time points with codes
GPS + GLONASS (12/8 satellites)
• 1700 h data logging at 15 s rate
• 6800 h data logging at 60 s rate
• 360000 real-time points with codes
GPS + GLONASS + Galileo (12/8/10 satellites)
• 800 h data logging at 15 s rate
• 3200 h data logging at 60 s rate
• 360000 real-time points with codes
GPS1200+ 117
Technical Data
Power
Battery internal
Battery external
Operating times
GPS1200+ 118
Power consumption: GX1230+ GNSS/GX1230+/GX1220+ GNSS/GX1220+/
GX1210+, radio and RX1200 excluded:
3.2 W typically, 270 mA
External supply voltage: Nominal 12 V DC ( , GEV71 car battery cable to a
12 V car battery), voltage range 10.5-28 V DC
Type:
Voltage:
Capacity:
Li-Ion
7.4 V
GEB221: 4.4 Ah
Type:
Voltage:
Capacity:
NiMH
12 V
GEB171: 9.0 Ah
The given operating times are valid for
• all receiver types except GRX1200+/GRX1200+ GNSS.
• receiver plus antenna plus RX1200 without keyboard illumination and without screen heating.
• two fully charged GEB221 batteries.
• room temperature. Operating times will be shorter when working in cold weather.
Environmental specifications
Equipment
Type
Static
Rover
Rover
Radio
-
Pacific Crest PDL, receive
-
Digital cellular phone
-
-
Siemens MC75
Operating time
17 h continuously
11 h continuously
11 h continuously
Temperature
Type
All receivers
Leica CompactFlash cards, all sizes
Battery internal
Operating temperature [°C] Storage temperature [°C]
-40 to +65 -40 to +80
-40 to +80 -40 to +80
-20 to +55 -40 to +70
Technical Data GPS1200+ 119
Technical Data
PPS output
GPS1200+
Protection against water, dust and sand
Type
All receivers
Protection
IP67 (IEC 60529)
Dusttight
Waterproof to 1 m temporary immersion
Humidity
Type
All receivers
Protection
Up to 100 %
The effects of condensation are to be effectively counteracted by periodically drying out the receiver.
For GX1200+ with PPS/Event option and GRX1200+/GRX1200+ GNSS
PPS output characteristics:
Peak:
Impedance:
Pulse length:
Leading edge:
3.3 V = High
50 Ω
1 ms
Coinciding with the beginning of each epoch.
120
PPS output characteristics:
Peak:
Positive/negative edge:
3.3 V = High
Selectable via RX1200.
Cable connectivity:
Matched with an appropriate impedance of: 50 Ω
Socket: LEMO ERN.0S.250.CTL
Technical Data GPS1200+ 121
Technical Data
Event input
GPS1200+
For GX1200+ with PPS/Event option and GRX1200+/GRX1200+ GNSS
Pulse type:
Pulse length:
Voltage:
Pin definition:
Socket:
TTL, positive or negative going pulse
125 ns at minimum
TTL level, ~ 5 V, min. 3.3 V
Centre = signal, Case = ground
LEMO HGP.00.250.CTL
External oscillator input
For GRX1200+/GRX1200+ GNSS
External clock input:
Frequency:
Input impedance:
Input VSWR:
Signal level:
Frequency stability:
Wave shape:
5 MHz or 10 MHz
50 Ω nominal
2:1 maximum
0 dBm minimum to +13.0 dBm maximum
±0.5 ppm maximum
Sinusoidal
Connector: MMCX female
122
7.2
Antennas Technical Data
Description and use
The antenna is selected for use based upon the application. The table gives a description and the intended use of the individual antennas.
Type
AX1201
Description Use
L1 SmartTrack antenna with built in groundplane.
With GX1210+ receiver.
AX1203+ GNSS GPS, GLONASS, Galileo,
Compass SmartTrack+ antenna with built in groundplane.
With GX1220+, GX1220+ GNSS,
GX1230+, GX1230+ GNSS receiver or GRX1200+ Series.
AT504 GG Dorne & Margolin L1/L2 antenna element with gold anodized choke ring groundplane. Complies with IGS type 'T' antenna, JPL design. Optional protective radome.
With GX1220+, GX1220+ GNSS,
GX1230+, GX1230+ GNSS or
GRX1200+ Series where higher precision is required.
For example static surveys of long baselines, tectonic plate monitoring and reference stations.
Technical Data GPS1200+ 123
Technical Data
Dimensions
Connector
Mounting
Weight
Type
AR25
Type
Height
Diameter
GPS1200+ 124
Description
Dorne & Margolin GPS,
GLONASS, Galileo,
Compass antenna element with gold anodized choke ring groundplane. Optional protective radome.
Use
With GX1220+, GX1220+ GNSS,
GX1230+, GX1230+ GNSS or
GRX1200+ Series where higher precision is required.
For example static surveys of long baselines, tectonic plate monitoring and reference stations.
AX1201/AX1203+ GNSS
6.2 cm
17.0 cm
AX1201/AX1203+ GNSS:
AT504 GG/AR25:
All antennas:
AX1201/AX1203+ GNSS:
TNC female
N female
AT504 GG
5/8" Whitworth
0.4 kg
14.0 cm
38.0 cm
AR25
20.0 cm
38.0 cm
Electrical data
Technical Data
AT504 GG:
AR25:
4.3 kg, radome 1.1 kg
7.6 kg, radome 1.1 kg
Type
Voltage
Current
Frequency
GPS L1
1575.42 MHz
GPS L2
1227.60 MHz
GPS L5
1176.45 MHz
GLONASS L1
1602.5625-
1611.5 MHz
GLONASS L2
1246.4375-
1254.3 MHz
AX1201 AX1203+ GNSS AT504 GG AR25
4.5 to 18 V DC 4.5 to 18 V DC 4.5 to 18 V DC 3.3 to 12 V DC
35 mA typical 35 mA typical 50 mA max 100 mA max
X
-
-
-
-
X
X
X
X
X
X
X
-
X
X
X
X
X
X
X
GPS1200+ 125
Technical Data
)
GPS1200+
Type
Galileo E1
1575.42 MHz
Galileo E5a
1176.45 MHz
Galileo E5b
1207.14 MHz
Galileo Alt-
BOC
1191.795 MHz
AX1201
-
-
-
-
Gain
(typically)
Noise Figure
(typically)
27 dBi
< 2 dBi
AX1203+ GNSS AT504 GG
29 dBi
< 2 dBi
X
X
X
X
29 dBi
-
-
-
-
3 dBi max
Galileo Alt-BOC covers bandwith of Galileo E5a and E5b.
AR25
X
X
X
X
126
40 dBi
< 1.2 dBi max
Environmental specifications
Temperature
Type
AX1201/
AX1203+ GNSS
AT504 GG
AR25
Operating temperature [°C] Storage temperature [°C]
-40 to +70
-40 to +70
-55 to +85
-55 to +85
-40 to +70
-55 to +90
Protection against water, dust and sand
Type
All antennas
Protection
IP67 (IEC 60529)
Dusttight
Protected against water jets
Waterproof to 1 m temporary immersion
Technical Data GPS1200+ 127
Technical Data
Cable length
GPS1200+ 128
Humidity
Type
All antennas
Protection
Up to 100 %
The effects of condensation are to be effectively counteracted by periodically drying out the antenna.
Separation distance from receiver ...
GX1230+ GNSS/
GX1220+ GNSS/
GX1230+/GX1220+/
GX1210+
GRX1200+/
GRX1200+ GNSS to antenna
AX1201/
AX1203+ GNSS
AT504 GG/AR25
AX1203+ GNSS
Supplied cable lengths [m]
1.2
2.8
1.2
2.8
10
Optional cable lengths [m]
30
50
70
30
50
70
7.3
Control unit
RX1200 Technical Data
Display:
Dimensions
Keyboard:
Angle Display:
Distance Display:
Touch screen if fitted:
1/4 VGA (320 x 240 pixels), monochrome
(RX1210/RX1250X) or color (RX1250Xc), graphics capable LCD, illumination, optional touch screen
62 keys including 12 function keys, illumination
360°’", 360° decimal, 400 gon, 6400 mil, V % m, ft int, ft us, ft int inch, ft us inch
Toughened film on glass
Type
RX1210
Length [m]
0.218
RX1250X/RX1250Xc 0.218
Width [m]
0.123
0.123
Thickness [m]
0.037
0.047
Weight
Type
RX1210
RX1250X/RX1250Xc with GEB211
Weight [kg]/[lbs]
0.480/1.058
0.741/1.634
Technical Data GPS1200+ 129
Technical Data
Recording
GPS1200+ 130
For RX1250X/RX1250Xc, data can be recorded on the CompactFlash card.
Type
CompactFlash card
Capacity [MB] Data capacity
•
•
256
1024
256 MB is typically sufficient for about
GPS only (12 satellites)
• 2000 h L1 + L2 + L5 data logging at 15 s rate
• 8000 h L1 + L2 + L5 data logging at 60 s rate
• 360000 real-time points with codes
GPS + GLONASS (12/8 satellites)
• 1700 h data logging at 15 s rate
• 6800 h data logging at 60 s rate
• 360000 real-time points with codes
GPS + GLONASS + Galileo (12/8/10 satellites)
• 800 h data logging at 15 s rate
• 3200 h data logging at 60 s rate
• 360000 real-time points with codes
Power
Internal battery
Environmental specifications
Technical Data
Type
RX1210
Consumption [W]
1
RX1250X/
RX1250Xc
1.1/
1.4
Bluetooth to SmartAntenna, digital cellular phone powered from GHT56
External supply voltage
Nominal voltage 12 V DC ( )
Voltage range 11.5 V-28 V
Nominal voltage 12 V DC ( )
Voltage range 11.5 V-28 V
Type
RX1250X/
RX1250Xc
Battery Voltage Capacity
Li-Ion 7.4 V
Operating time, typical
GEB211: 2.2 Ah 12 h/
11 h
Bluetooth to SmartAntenna
Temperature
Type
RX1200
Operating temperature [°C]
-30 to +65
Bluetooth: -25 to +65
Color display: -30 to +50
GPS1200+
Storage temperature [°C]
-40 to +80
131
Technical Data
Ports
GPS1200+
Protection against water, dust and sand
Type
RX1200
Protection
IP67 (IEC 60529)
Dusttight
Waterproof to 1 m temporary immersion
132
Humidity
Type
RX1200
Protection
Up to 100 %
The effects of condensation are to be effectively counteracted by periodically drying out the RX1200.
Type
RX1210
8 pin LEMO-1 Special clip-on interface
For power and/or communication For power and communication to
GPS1200+
Type
RX1250X/
RX1250Xc
8 pin LEMO-1 Special clip-on interface
For power and/or communication For communication to GHT56 and GPS1200+
Technical Data GPS1200+ 133
Technical Data
7.4
GPS1200+
Conformity to National Regulations
7.4.1
RX1250
Conformity to national regulations
134
• FCC Part 15 (applicable in US)
• Hereby, Leica Geosystems AG, declares that the RX1250 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
Class 1 equipment according European Directive 1999/5/EC
(R&TTE) can be placed on the market and be put into service without restrictions in any EU Member state.
• The conformity for countries with other national regulations not covered by the
FCC part 15 or European directive 1999/5/EC has to be approved prior to use and operation.
Frequency band
Type
RX1250, Bluetooth
Frequency band [MHz]
2400 - 2483.5
Ouput power
Antenna
Type
RX1250, Bluetooth
Type
RX1250, Bluetooth
Output power [mW]
2.5
Antenna
Integrated antenna
Gain
[dBi]
-
Connector Frequency band
[MHz]
-
Technical Data GPS1200+ 135
Technical Data
7.4.2
Receiver
Conformity to national regulations
GPS1200+ 136
• FCC Part 15 (applicable in US)
• Hereby, Leica Geosystems AG, declares that the Receiver is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
Class 1 equipment according European Directive 1999/5/EC
(R&TTE) can be placed on the market and be put into service without restrictions in any EU Member state.
• The conformity for countries with other national regulations not covered by the
FCC part 15 or European directive 1999/5/EC has to be approved prior to use and operation.
Frequency band
Type
GX1210+
GX1230+/GX1220+/GRX1200+
Frequency band [MHz]
1575.42
1227.60
1575.42
Output power
Antenna
Type
GX1230+ GNSS/GX1220+ GNSS/
GRX1200+ GNSS
Frequency band [MHz]
1176.45
1191.795
1207.14
1227.60
1246.4375 - 1254.3
1575.42
1602.4375 - 1611.5
Type
Receiver
Type
Output power [mW]
Receive only
External GNSS antenna element (receive only)
Technical Data GPS1200+ 137
Technical Data
7.4.3
GFU24, Siemens MC75
Conformity to national regulations
Frequency band
Output power
GPS1200+ 138
• FCC Part 15, 22 and 24 (applicable in US)
• Hereby, Leica Geosystems AG, declares that the GFU24 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
Class 1 equipment according European Directive 1999/5/EC
(R&TTE) can be placed on the market and be put into service without restrictions in any EU Member state.
• The conformity for countries with other national regulations not covered by the
FCC part 15, 22 and 24 or European directive 1999/5/EC has to be approved prior to use and operation.
Quad-Band EGSM850 / EGSM900 / GSM1800 / GSM1900 MHz
EGSM850:
EGSM900:
GSM1800:
GSM1900:
2 W
2 W
1 W
1 W
Antennas
Specific Absorption Rate (SAR)
Type
Frequency band
Type
Gain
Connector
GAT 3
900 or 1800 MHz
Detachable λ/2 antenna
0 dBi
TNC
GAT 5
850 or 1900 MHz
Detachable λ/2 antenna
0 dBi
TNC
The product meets the limits for the maximum permissible exposure of the guidelines and standards which are force in this respect. The product must be used with the recommended antenna. A separation distance of at least 20 centimeters should be kept between the antenna and the body of the user or nearby person within the intended application.
Technical Data GPS1200+ 139
Technical Data
7.4.4
GPS1200+
GFU19 (US), GFU25 (CAN), GFU26 (US) CDMA MultiTech MTMMC-C
140
Conformity to national regulations
Frequency band
Output power
• FCC Part 15, 22 and 24 (applicable in US)
• The conformity for countries with other national regulations not covered by the
FCC part 15, 22 and 24 has to be approved prior to use and operation.
Dual-Band CDMA850/CDMA1900 MHz
CDMA850: 2 W
CDMA1900: 0.4 W
Antenna
Type
Frequency band
Type
Gain
Connector
GAT 5
850 or 1900 MHz
Detachable λ/2 antenna
0 dBi
TNC
Specific Absorption Rate (SAR)
The product meets the limits for the maximum permissible exposure of the guidelines and standards which are force in this respect. The product must be used with the recommended antenna. A separation distance of at least 20 centimeters should be kept between the antenna and the body of the user or nearby person within the intended application.
Technical Data GPS1200+ 141
International Limited Warranty, Software
License Agreement
8 ment
GPS1200+
International Limited Warranty, Software License Agree-
142
International
Limited Warranty
Software Licence
Agreement
This product is subject to the terms and conditions set out in the International Limited
Warranty which you can download from the Leica Geosystems home page at http://www.leica-geosystems.com/internationalwarranty or collect from your Leica
Geosystems distributor.
The foregoing warranty is exclusive and is in lieu of all other warranties, terms or conditions, express or implied, either in fact or by operation of law, statutory or otherwise, including warranties, terms or conditions of merchantability, fitness for a particular purpose, satisfactory quality and non-infringement, all of which are expressly disclaimed.
This product contains software that is preinstalled on the product, or that is supplied to you on a data carrier medium, or that can be downloaded by you online pursuant to prior authorization from Leica Geosystems. Such software is protected by copyright and other laws and its use is defined and regulated by the Leica Geosystems
Software Licence Agreement, which covers aspects such as, but not limited to,
Scope of the Licence, Warranty, Intellectual Property Rights, Limitation of Liability,
Exclusion of other Assurances, Governing Law and Place of Jurisdiction. Please
make sure, that at any time you fully comply with the terms and conditions of the
Leica Geosystems Software Licence Agreement.
Such agreement is provided together with all products and can also be referred to and downloaded at the Leica Geosystems home page at http://www.leica-geosystems.com/swlicense or collected from your Leica Geosystems dealer.
You must not install or use the software unless you have read and accepted the terms and conditions of the Leica Geosystems Software Licence Agreement. Installation or use of the software or any part thereof, is deemed to be an acceptance of all the terms and conditions of such licence agreement. If you do not agree to all or some of the terms of such licence agreement, you may not download, install or use the software and you must return the unused software together with its accompanying documentation and the purchase receipt to the dealer from whom you purchased the product within ten (10) days of purchase to obtain a full refund of the purchase price.
International Limited Warranty, Software
License Agreement
GPS1200+ 143
Index GPS1200+ 144
Index
A
AC, power supply unit ......................................... 20
In Diagram ...................................................... 70
Accuracy ............................................................ 113
Antennas ........................................................... 123
Type ............................................................. 123
Used with receivers ........................................ 13
Application program software .............................. 14
Area, icon ............................................................ 34
Attach, clip-on-housing ........................................ 46
B
Battery
Change in receiver ......................................... 39
External, receiver ......................................... 118
For internal power supply .............................. 20
Icon ................................................................ 34
Internal, receiver .......................................... 118
RX1200 ........................................................ 131
Baud rate ............................................................ 76
Bluetooth, icon .................................................... 34
C
Capacity, memory
Receiver ....................................................... 117
RX1200 ........................................................ 130
Choicelist ............................................................ 30
Clip-on-housing
Attach ............................................................. 46
Detach ............................................................ 46
Commands, remote control ................................. 67
Communication parameters
Remote interface ............................................ 76
CompactFlash card ............................................. 41
Format ............................................................ 43
Icon ................................................................ 34
Insert .............................................................. 41
Memory device ............................................... 18
Remove .......................................................... 41
Safety instructions .......................................... 41
Connector, antennas ......................................... 124
Container contents .............................................. 22
Conversion of data .............................................. 19
D
Data bits .............................................................. 76
Data conversion .................................................. 19
Data exchange
Between receiver and PC .............................. 14
Data storage ....................................................... 18
Reference station ........................................... 66
Data streaming, reference station ....................... 66
Detach, clip-on-housing ...................................... 46
Device
Clip-on-housing .............................................. 45
Status ............................................................. 51
Dimensions
Antennas ...................................................... 124
Receivers ..................................................... 116
RX1200 ........................................................ 129
Documentation ...................................................... 4
Drive
OMNI ............................................................. 19
PC card, on office computer .......................... 19
Index GPS1200+ 145
Index
E
Electrical data, antennas ................................... 125
Environmental specifications
Antenna ........................................................ 127
Receiver ....................................................... 119
RX1200 ........................................................ 131
Equipment setup ........................................... 36, 68
Event input ........................................................ 122
Exchange data
Between receiver and PC .............................. 14
External power supply ......................................... 20
GPS1200+ 146
G
GAT 3, antenna ................................................. 139
GeoC++ .............................................................. 17
GFU19 .............................................................. 140
GFU24 .............................................................. 138
GFU25 .............................................................. 140
GFU26 .............................................................. 140
H
Housing for devices ............................................ 45
F
Flashing LED on clip-on-housing ........................ 53
Flow control ......................................................... 76
Format CompactFlash card ................................. 43
Frequency band
GFU19, MultiTech MTMMC-C ..................... 140
GFU24, Siemens MC45 ............................... 138
GFU25, MultiTech MTMMC-C ..................... 140
GFU26, MultiTech MTMMC-C ..................... 140
I
Icons ................................................................... 33
Indicators, LED for clip-on-housing ..................... 51
Insert
CompactFlash card ........................................ 41
SIM card ........................................................ 47
Interface
Remote .......................................................... 76
User ............................................................... 26
Internal memory .................................................. 18
Icon ................................................................ 34
Internal power supply .......................................... 20
Internet online status, icon .................................. 33
K
Keyboard ............................................................. 26
Keyboard, lock and unlock .................................. 26
Leica SmartWorx software on RX1250
Access ........................................................... 28
Activate .......................................................... 27
Exit ................................................................. 28
Minimise ......................................................... 28
LGO .................................................................... 14
Light Emitting Diode, clip-on-housing ................. 51
Li-Ion battery ..................................................... 118
Storage .......................................................... 83
Line, icon ............................................................. 34
Lock, keyboard .................................................... 26
L
Labelling
RX1210 ........................................................ 106
RX1250 X ..................................................... 106
RX1250 Xc ................................................... 106
LED
Clip-on-housing, description ........................... 52
Housing .......................................................... 51
LEICA
Geo Office ................................................ 10, 14
GNSS Spider ............................................ 10, 15
M
Memory device, available ................................... 18
Menu, select from ............................................... 29
Mount, antennas ............................................... 124
MultiTech MTMMC-C
N
GFU19/GFU25/GFU26, technical data ........ 140
NiCd battery ...................................................... 118
Index GPS1200+ 147
Index
O
OFF button .................................................... 24, 37
OMNI drive .......................................................... 19
ON button ...................................................... 24, 37
Operating times ................................................. 118
Operation
GRX1200+/GRX1200+ GNSS ....................... 73
GX1200+ ........................................................ 60
Output power
GFU19, MultiTech MTMMC-C ..................... 140
GFU24, Siemens MC75 ............................... 138
GFU25, MultiTech MTMMC-C ..................... 140
GFU26, MultiTech MTMMC-C ..................... 140
P
GPS1200+ 148
Power .................................................................. 20
RX1200 ........................................................ 131
Power supply unit
AC, reference station setup ........................... 70
Power, receivers ............................................... 118
PPS output ........................................................ 120
Parameters, remote interface .............................. 76
Parity ................................................................... 76
PC card drive on office computer ........................ 19
Ports on RX1200 ............................................... 132
Position mode, icon ............................................. 33
Position status, icon ............................................ 33
Q
Quick coding, icon ............................................... 35
R
Raw data transfer to LGO ................................... 19
Real-time device, icon ......................................... 33
Real-time status, icon ......................................... 33
Receiver components ......................................... 24
Receivers ............................................................ 11
Recording .......................................................... 116
RX1200 ........................................................ 130
Remote control
Commands .................................................... 67
Reference station ........................................... 74
Remote interface ................................................. 76
Remove
CompactFlash card ........................................ 41
SIM card ......................................................... 49
RX1200
Operating GRX1200+/GRX1200+ GNSS ...... 73
With/without touch screen ................................ 4
RX1200 technical data ...................................... 129
S
Satellites
Icon, contributing ............................................ 33
Icon, visible .................................................... 33
Select from menu ................................................ 29
Setup ................................................................... 36
Reference station ........................................... 68
SHIFT .................................................................. 35
Icon ................................................................ 35
Siemens MC75
GFU24, technical data ................................. 138
SIM card
Insert .............................................................. 47
Remove ......................................................... 49
Software
Application programs ..................................... 17
Customised application programs ................. 17
Language ....................................................... 16
RX1200 .......................................................... 17
System ........................................................... 16
Type ............................................................... 16
Upload ........................................................... 17
Specifications, environmental ........................... 110
Antennas ...................................................... 127
Receiver ....................................................... 119
RX1200 ........................................................ 131
Status, device ..................................................... 51
Stop bit ................................................................ 76
Survey application program ................................ 55
Switching, Leica SmartWorx software and
Windows CE ....................................................... 27
System software ................................................. 14
Index GPS1200+ 149
Index
T
Technical data ................................................... 110
Receiver ....................................................... 116
Temperature
Antenna
Operating ................................................ 127
Storage ................................................... 127
Battery internal
Charging .................................................... 38
Operating ................................................ 119
Storage ................................................... 119
CompactFlash card
Operating ................................................ 119
Storage ................................................... 119
Receiver
Operating ................................................ 119
Storage ................................................... 119
RX1200
Operating ................................................ 131
Storage ................................................... 131
GPS1200+ 150
Temperature range
Receiver, drying ............................................. 84
Time, operating ................................................. 118
Touch screen ...................................................... 26
Tracking characteristics .................................... 110
Transfer raw data to LGO ................................... 19
U
Uninterruptible Power Supply ............................. 21
Unlock, keyboard ................................................ 26
Upload software .................................................. 17
UPS ..................................................................... 21
User interface ...................................................... 26
W
Weight
Antennas ...................................................... 124
Receiver ....................................................... 116
RX1200 ........................................................ 129
Windows CE desktop, access ............................. 28
Windows CE, activate ......................................... 27
Windows key symbol ........................................... 28
Index GPS1200+ 151
Total Quality Management: Our commitment to total customer satisfaction.
Leica Geosystems AG, Heerbrugg, Switzerland, has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems (ISO standard 9001) and Environmental
Management Systems (ISO standard 14001).
Ask your local Leica Geosystems dealer for more information about our TQM program.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Phone +41 71 727 31 31 www.leica-geosystems.com
Λήψη
Δημόσιος σύνδεσμος ενημερώθηκε
Ο δημόσιος σύνδεσμος για τη συνομιλία σας ενημερώθηκε. You may view and manage your chat links after registration here.
Δημόσιος σύνδεσμος εγγράφου
Διαφήμιση