RedMax HBZ2610 Operator`s manual

HBZ2610

848-L0T-93A0 (001)

OWNER'S/OPERATOR'S

MANUAL

BLOWERS

U

S

HBZ2610

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING

Before using our products, please read this manual carefully to understand the proper use of your unit.

This spark ignition system complies with the Canadian standard ICES-002.

APPLICABLE SERIAL NUMBERS :

00100101 and up

US-1

HBZ2610

Contents

SAFETY FIRST

Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.

Note that there may be times when warning seals peel off or become soiled and impossible to read. If this happens, you should contact the dealer from which you purchased the product to order new seals and affix the new seal(s) in the required location(s).

■

NOTES ON TYPES OF WARNINGS

WARNING

Instructions labeled as shown at left, concern critical steps or procedures which must be followed in order to prevent accidents which could lead to serious bodily injury or death.This mark is used to indicate instructions which must be followed without exception.

IMPORTANT

Instructions labeled as shown at left concern steps or procedures which, if not followed correctly, could lead to mechanical failure, breakdown, or damage.

NOTE

Used to label supplementary instructions designed to provide hints or directions useful in the use of the product.

WARNING

1. Read this Blower Owner/Operator

Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury.

2. Be sure to keep this manual handy so that you may refer to it later whenever any questions arise. Also note that you are requested to contact the dealer from whom you purchased the product for assistance the event that you have any questions which cannot be answered herein.

3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

4. Do not lend or rent your machine without the owner's manual.

5. Be sure that anyone using your unit understands the infomation contained in this manual.

6. Never let a child under 13 years old use the machine.

1. Parts location......................................................................3

2. Specifications .....................................................................3

3. Warning labels on the machine ..........................................4

4. Symbols on the machine ....................................................4

5. For safe operation ..............................................................5

6. Set up .................................................................................8

7. Fuel.....................................................................................9

8. Operation..........................................................................11

9. Maintenance .....................................................................12

10. Storage .............................................................................14

11. Disposal............................................................................14

12. Optional vacuum kit usage ...............................................14

13. Troubleshooting guide ......................................................14

US-2

1. Parts location

(1) Stop switch

(2) Throttle trigger

(3) Air inlet screen

(4) Spark plug cap

(5) Recoil starter knob

(6) Air cleaner

(7) Fuel tank

(8) Blower pipe

(9) Screw

HBZ2610

U

S

2. Specifications

■

MODEL HBZ2610

Dimensions (L x W x H) mm (in) ···············································································327x269x360 (12.9x10.6x14.2)

Dry Weight kg (lbs) ········································································································································4.1 (9.0)

Fuel Tank Capacity liter (fl. oz)··················································································································0.65 (22.0)

Engine Type ··········································································································Air cooled 2-cycle gasoline engine

Piston Displacement cm

3

(cu. in) ···············································································································25.4 (1.60)

Carburetor valve type·············································································································Walbro Diaphragm type

Ignition System ···················································································································································C.D.I.

Spark Plug························································································································NGK CMR7H (Noise-proof)

Muffler ·································································································································Spark arrester equipped

Operating Engine Speed rpm ················································································································2800 to 7600

Average Air Volume (w/std Pipe) cu. m/min (cfm)······················································································10.0 (353)

Max. Air Velocity m/sec (mph)·······················································································································55 (112)

Emission Compliance Period hrs. ························································································································300

Noise Level (50 Feet ANSI B175. 2000) dB(A) ·······································································································72

Specifications are subject to change without notice.

US-3

HBZ2610

3. Warning labels on the machine

(1) Read owner's manual before operating this machine.

(2) Wear head, eye and ear protection.

(3) Handling this machine improperly could result in accidents causing serious injury or death.

Read this manual carefully and practice using the blower until you are fully acquainted with all operations and have learned to use it correctly.

(4) Severing of fingers or hand by fan blade.

Do not open or remove safety guards or nets while engine is running.

(5) Thrown or blown object.

Stay a safe distance from the machine.

IMPORTANT

If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s).

WARNING

Never modify your machine.

We won't warrant the machine, if you use the remodeled machine or you don't observe the proper usage written in the manual.

4. Symbols on the machine

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position:

Fuel tank cap

(b) The direction to close the choke

Position:

Air cleaner body

(c) The direction to open the choke

Position:

Air cleaner body

■

EMISSION CONTROL

An emission control label is located on the machine.

EMISSION CONTROL INFORMATION

THIS ENGINE MEETS U.S. EPA AND CALIFORNIA

EXH/EVP REGS FOR

2009*

1

S.O.R.E.

ENGINE FAMILY : 9HQZS.0254BH*

2

DISPL.: 25cc

EMISSION CONTROL SYSTEM : EXH;EM/EVP;SP*

3

COMPLIANCE PERIOD : 300 HOURS

REFER TO OPERATOR'S MANUAL FOR MAINTE-

NANCE, SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

USE JASO FD OR ISO L-EGD GRADE 50:1 OIL

*1: The year will be changed every year of manufacturing.

*2: The initial will be changed every year of manufacturing.

*3: SP : Sealed tank made of HDPE or PE.

US-4

5. For safe operation

WARNING

• The blower is used for blowing away leaves and other debris on the ground.

When operating the blower, the operater must stand with both feet firmly on the ground.

Do not operate the blower while standing on a ladder or a stand.

• Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories and parts. Non-authorized modifications and/or accessories or parts can result in serious personal injury or the death of the operator or others.

• When planning your work schedule, allow plenty of time to rest. Limit the amount of time over which the product is to be used continuously to somewhere around 30 ~ 40 minutes per session. Also try to keep the total amount of work performed in a single day under 2 hours or less.

■

Basic safety rules

1. Never operate a blower when you are fatigued, ill, or upset, or under the influence of madication that may make you drowsy, or if you are under the influence of alcohol or drugs.

2. Wear the following protective equipments when operating the blower. a: Approved ear protection to reduce the risk of hearing loss. b: Approved (ANSI Z87.1.) eye protection and foot protection to reduce the risk of injury associated with thrown objects. c: Face filter mask in dusty conditions to reduce the risk of injury associated with the inhalation of dust. d: Wear sturdy rubber-soled shoes or shoes with some other form of anti-slip protection to help protect you against falling. e: Wear thick anti-vibration gloves to reduce the risk of whitefinger disease. f: Do not wear loose clothing, scarves, neck chains, unconfineed long hair, and like to reduce the risk of injury associated with objects being drawn into air intake and rotating parts.

Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury.

HBZ2610

3. The ignition system of your unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemaker should consult their physician and the pacemaker munufacturer before operating this tool.

4. Do not allow other persons to be near the blower when starting. Keep bystanders and animals out of the work area.

Children, pets and bystanders should be a minimum of 50 feet (15 meters) away when you operate the blower.

5. Avoid using the blower where stable footing and balance are not assured.

6. All blower service, other than the items listed in the Owner's Manual, should be performed by competent service personnel. (E.g., if improper service to the blower fan and muffler could cause a hazardous failure.)

7. Always shut off the engine before setting it down.

8. Operate the blower only in well ventilated areas. Never start or run the engine inside a closed room or building and potentially explosive atmosphere. Exhaust fumes contain dangerous carbon monoxide.

9. Never to touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an electrical shock.

10. Never to touch the muffler, spark plug, other metallic parts of the engine or engine cover while the engine is in operation or immediately after shutting down the engine. These metallic parts and engine cover reach high temperatures during operation and doing so could result in serious burns.

11. Never remove debris from the inlet screen while the engine is running.

Contact with rotating blower fan result in a serious personal injury.

(1) Screw

(2) Air inlet screen

U

S

■

Before use

1. Each time before starting the engine, inspect the entire unit to see if every part is in good order and is securely tightened in place. If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been repaired.

US-5

HBZ2610

5. For safe operation

WARNING

2. Never use the blower without the screen at the air intake of the blower.

Before each use, check that, the screw

(1) is securely tightened and is free from any damage.

3. Check the work area that the blower will be used in and remove or cover all valuables that may be damaged by the air blast or thrown debris.

■

Using the product

1. To reduce the risk of injury associated with thrown objects. a: Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away. b: Use the full blower nozzle extension so the air stream can work close to the ground. c: Do not allow bystaders in work area. d: Do not point the blower tube in the direction of people or pets. e: Always check to be sure that no debris has been blown onto someone else's property. f: Pay attention to the direction of the wind, do not work against the wind. g: Never point a blower tube toward an open flame to avoid the possibility of igniting the unit, causing injury to yourself or damage to surroundings.

2. To minimize blowing time. a: Use rakes and brooms to loosen debris before blowing. b: In dusty conditions, slightly dampen surfaces. c: Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches and gardens.

3. If you detect abnormal vibration or noise during operaion, promptly stop the blower and check whether something has broken.

If a breakdown has occurred, do not operate the blower until the problem is fixed.

4. After using blowers and other equipment,

CLEAN UP! Dispose of debris in trash receptacles.

US-6

■

Transport

1. Drain the fuel from the fuel tank before transporting or storing the blower.

2. Secure the unit carefully to prevent movement when it is transported.

3. A unit that receives a strong shock during transport and unloading may malfunction.

■

Fuel safety

1. Always use caution when handling fuel.

It is highly flammable. Wipe up all spills and then move the blower at least 10 feet

(3 meters) from the fueling point before starting the engine.

2. Eliminate all sources of sparks or flame

(i.e. smoking, open flames, or work that can cause sparks) in the areas where fuel is mixed, poured, or stored.

3. Do not smoke while handling fuel or while operating the blower.

4. Do not refuel a hot engine.

5. Do not refuel a running engine.

6. Keep the handles dry, clean and free of oil or fuel mixture.

7. Always store fuel in an approved container designed for that purpose.

■

Storage

1. Always store the blower and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric moters, relays/switches, boilers and the like.

2. For longer period of storage, the fuel tank should be emptied.

3. When storing the blower, choose a space indoors free from moisture and out of the reach of children.

■

Avoid noise problem

IMPORTANT

Check and follow the local regulations as to sound level and hours of operations for blower.

1. Operate power equipment only at reasonable hours not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances.

2. To reduce sound levels, limit the number of pieces of equipment used at any one time.

3. Operate power blowers at the lowest possible throttle speed to do the job.

4. Check your equipment before operation, especially the muffler, air intakes and air

5. For safe operation

filters.

■

For protecting your body from vibration

WARNING

Prolonged use of a blower, exposing the operater to vibrations and cold may produce whitefinger disease (Raynaud's phenomenon), which symptoms are tingling and burning sensations followed by loss of color and numbness in the fingers.

All factors which contribute to whitefinger disease are not known, but cold weather, smoking diseases or physical conditions as well as long periods of exposure to vibration are mentioned as factors.

In order to reduce the risk of whitefinger disease, the following precautions are strongly recommended.

a: Keep your body warm. Never use blower during rains. b: Wear thick anti-vibration gloves. c: Take more than 5 minutes of break in warm place frequently. d: Maintain a firm grip at all times, but do not squeeze the handles with constant, excessive pressures. e: If you feel discomfort, redness and swelling of your fingers or any other part of your body, see a doctor before getting worse.

■

Maintenance

1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals.

2. Always be sure to turn off the engine and disconnect the spark plug before performing any maintenance or checking procedures.

WARNING

The metallic parts and engine cover reach high temperatures immediately after stopping the engine.

3. Examine the blower at intervals for loose fasteners and rusted or damaged parts.

Use special care around the fuel line, the muffler, and the ignition wiring.

4. When replacing the any other part, or any lubricant, always be sure to use only

RedMax products or products which have been certified by RedMax for use with the

HBZ2610

RedMax product.

5. In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

6. Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

7. Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

■

Disposal

When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations.

U

S

US-7

HBZ2610

6. Set up

F1

F2

■

BLOWER PIPE

• Align groove in blower pipe with projection on blower housing (or another blower pipe) and slide the pipe onto the blower housing (or another blower pipe).

Rotate the pipe clockwise to lock it into place.

■

INSTALLING SUPPORT HANDLE

• This handle is supplied with the blower.

• Fit the holes of volute and handle, tighten the screws.

• Be sure to tighten the screws straightly.

(1) Support Handle

(2) Holes

(3) Screws

US-8

HBZ2610

7. Fuel

FUEL

lines or fuel tank of the engine.

WARNING

• Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10 ft (3 m) away from the fueling point before starting the engine.

NOTE

• Failures caused by operating engines on gasoline with octane rating lower than 89 are not covered by the RedMax Two-

Stroke engine warranty.

■

GASOLINE REQUIREMENTS

• All 2-Stroke RedMax Products are powered by RedMax

Professional-Commercial Duty, Hi-Performance, Hi-RPM,

Air

Cooled

2-Stroke engines.

RedMax – Hi-Performance 2-stroke engines produce higher HP outputs as compared to standard Home Owner Duty or Light

Commercial Duty production engines offered by most manufacturers.

• Exhaust emission are controlled by the fundamental engine parameters and components (eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

• The RedMax Engines are registered and certified with CARB

(California Air Resources Board) and EPA (Environmental

Protection Agency) to operate on CLEAN Mid-grade 89 octane or Premium, unleaded (lead-free) gasoline and RedMax Air-

Cooled "Max Life", Synthetic blend Premium two-stroke engine oil mixed at 50:1 ratio.

• Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

• This Hi-Performance Air Cooled 2-stroke Engine requires the use of

Minimum

89 Octane (Mid grade or Premium)

2 clean gasoline. Gasoline may contain maximum of 10% Ethanol

(grain alcohol) or up to 15% MTBE (Methyl tertiary-butyl ether).

Gasoline containing Methanol (Wood Alcohol) is

NOT

approved.

WARNING

• Alternative Fuels (Not Gasoline)

Alternative fuels, such as E-15 (15% ethanol), E-20 (20% ethanol), E-85 (85% ethanol) are NOT classified as gasoline and are NOT approved for use in RedMax 2-stroke gasoline engines. Use of alternative fuels will cause major engine performance and durability problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc... Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

■

OIL REQUIREMENTS

• Use only RedMax "Max Life", Synthetic blend Premium Air-

Cooled two-stroke engine oil or oil certified to ISO-L-

EGD

(ISO/CD1378) standard AND one that is JASO-

FD

registered.

RedMax Air-Cooled "Max Life", Synthetic blend Premium two stroke engine oil and ISO-L-

EGD

(ISO/CD1378) AND JASO-

FD

oils are fully compatible with gasoline's containing 10% Ethanol.

RedMax Air-Cooled "Max Life", Synthetic blend Premium two stroke engine oil and ISO-L-

EGD

(ISO/CD1378) AND JASO-

FD

oils are

Universal

and should be mixed at 50:1 ratio for all 2 stroke air cooled engines sold in the past regardless of mixing ratios specified in those manuals.

• If the oil is registered with JASO, the JASO Logo with

FD

and registration number will be displayed on the container. The highest JASO rating is "FD", which equals the ISO-L-

EGD

rating. Lower ratings are "FC", "FB", and "FA".

U

S

NOTE

• IF octane rating of the Mid Grade gasoline in your area is lower than 89 Octane use Premium Unleaded Gasoline. The majority of all 2-stroke engine manufacturers in the USA and Canada recommend using gasoline with 89 Octane or higher.

• Engine problems due to inadequate lubrication caused by failure to use ISO-L-

EGD

certified and JASO

FD

registered oil such as "MaxLife", RedMax Synthetic blend Premium 2-stroke oil

WILL VOID THE REDMAX TWO-STROKE ENGINE

WARRANTY.

WARNING

• Gasoline with an octane rating lower than 89 will greatly increase the engines operating temperature. Low octane gasoline will cause detonation (knock) resulting in piston seizures and major internal engine components damage.

• Poor quality gasolines or oils may damage sealing rings, fuel

WARNING

• Do not use NMMA (National Marine Manufacturers

Association), BIA (Boating Industry Association), and TCW (two cycle water cooled) oils designed for MoPeds or Outboard, water cooled Marine Engines. Do not use API (American

Petroleum Institute), TC (Two Cycle) labeled oils. The API-TC

US-9

HBZ2610

7. Fuel

test standard has been discontinued by API in 1995 and it no longer exists.

IMPORTANT

• Gasoline/Oil mixture Storage Recommendations

Store your gasoline or gasoline/oil mixture in a cool dry area in a tightly sealed approved container to limit the entry of moisture and additional air (oxygen). Moisture and air cause the development of varnish and gum, making the fuel stale. Stored gasoline and gasoline/oil mixture ages and loses its octane rating and volatility. Do not mix more gasoline/oil than you intend to use in 30 days, and 60 days when fuel stabilizer is added. RedMax Air-Cooled "Max Life" Synthetic blend

Premium two-stroke engine oil

"Contains fuel stabilizer"

and will automatically extend your gasoline/oil mixture life up to 60 days.

■

HOW TO MIX FUEL

RECOMMENDED MIXING RATIO

GASOLINE 50 : OIL 1

(when using RedMax Air-Cooled "Max

Life")

50:1 MIXING CHART

GASOLINE gal.

2-CYCLE OIL fl.oz

1 2 3 4 5

2.6

5.2

7.8

10.4

13

GASOLINE liter

2-CYCLE OIL ml

1 2 3 4 5

20 40 60 80 100

WARNING

1. Select flat and bare ground for fueling.

2. Move at least 10 feet (3 meters) away from the fueling point before starting the engine.

3. Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

■

FOR YOUR ENGINE LIFE, AVOID

1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring seizure.

4.

Mixed fuels which have been left unused for a period of one month or more

may clog the carburetor and result in the engine failing to operate properly.

5. In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, Start the engine and run the carburetor dry residual fuel.

6. In the case of scrapping the used mixed oil container, scrap it only at an authorized depository site.

NOTE

• As for details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to the mixed gasoline, type of oil or fuel to be used. described therein, it may not be covered by the warranty.

WARNING

• Pay attention to agitation.

1. Measure out the quantities of gasoline and oil to be mixed.

2. Put some of the gasoline into a clean, approved fuel container.

3. Pour in all of the oil and agitate well for 10seconds.

4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizure due to abnormally lean mixture.

5. Place a clear indication on the outside of the container to avoid mixing up with gasoline or other containers that dont contain oil.

6. Indicate the contents on outside of container for easy identification.

■

FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the cap on a clean surface.

2. Put fuel into the fuel tank to 80% of the full capacity.

3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

US-10

8. Operation

F3

■

STARTING ENGINE

1. Rest the unit on a flat, firm place.

2. Pump the primer until fuel flows out in the clear tube.

(1) Primer

F7

F4

3. Move the choke lever upward to close the choke.

(1) Choke lever

(2) Close

(3) Open

F5

F6

4. Holding the blower handle, pull the starter rope with your right hand.

(Throttle trigger in idling position.)

NOTE

Avoid pulling the rope to its dead end or returning it by releasing the knob. Such actions can cause starter failures.

5. When the engine has started, move the choke lever gradually downward to open the choke.

6. Allow the engine to warm up for a half minute before starting operation.

■

RESTARTING ENGINE WHILE

ENGINE IS HOT

1. When restarting the engine immediately after stopping it, leave the choke open.

2. If the engine won't start after several attempts, close the choke and repeat pulling the rope or remove the spark plug and dry it.

■

STOPPING ENGINE

Move the throttle trigger to the idling position and press the stop switch (red button) until the engine comes to a complete stop.

(1) Stop switch

HBZ2610

NOTE

Except for an emergency, avoid stopping the engine while pulling the throttle trigger.

■

ADJUSTING IDLE SPEED

1. When the engine tends to stop frequently at an idle mode, turn the adjusting screw clockwise.

(1) Idle adjusting screw

(2) Cable adjuster

NOTE

Warm up the engine before adjusting the idle speed.

U

S

US-11

HBZ2610

9. Maintenance

Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.

■

MAINTENANCE CHART

system/compornent procedure fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug wipe out inspect/clean see

■

ADJUSTING

IDLING SPEED (p.11) clean and readjust plug gap cylinder fins, intake air cooling vent clean muffler, spark arrester, cylinder exhaust port clean throttle trigger, stop switch screws/nuts/bolts check operation tighten/replace every every every

25 50 100 before hours hours hours note use after after after

✔

✔ ✔ replace, if necessary

✔ replace carburetor if necessary

✔

GAP: .025in(0.6~0.7mm) replace, if necessary

✔

✔

✔

✔ ✔ not adjusting screws

F8

F9

WARNING

Make sure that the engine has stopped and is cool before performing any service to the blower. Contact with rotating blower fan or hot muffler may result in a personal injury.

■

AIR CLEANER

• Check the air cleaner every 25 hours of use or more frequently if used under dusty conditions. A clogged air filter may increase fuel consumption while cutting down the engine power. Never operate the blower without the air filter or with a deformed filter element because unfiltered dusty air may quickly ruin the engine.

CLEANING AIR FILTER:

1. Remove the air cleaner cover.

2. Use neutral detergent and warm water to clean the filter element. After cleaning, air dry the element completely.

3. Reinstall the filter.

Never forget to attach the screen. If the screen is not attached, the cleaner will not seal properly and the dusts come into the cylinder.

(1) Element

(2) Screen

■

FUEL FILTER

• A clogged fuel filter may cause poor acceleration of the engine. Check periodically to see if the filter is clogged

F10

F11

with dirt. The filter can be taken out of the fueling port using a small wire hook.

Disconnect the filter assembly from the fuel pipe and unhook the retainer to disassemble it. Clean the components with gasoline.

(1) Screen

(2) Element

(3) Holder

(4) Retainer

■

SPARK PLUG

• The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to .025 in (0.6~0.7mm).

• Plug manufacturers recommend replacing the plug twice a year to avoid unexpected plug failure in a job.

REPLACEMENT PLUG IS A NGK

CMR7H.

IMPORTANT

• Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.

• To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench.

US-12

9. Maintenance

■

MUFFLER

WARNING

• Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, do not use the blower and have it repaired immediately.

• Note that failing to do so may result in the engine catching on fire.

F12

F13

IMPORTANT

• Before starting operation, always make sure to check if the muffler is properly held by three bolts to the cylinder.

(Fastening Torque : 70~110 kg·cm)

• Even if one bolt out of three bolts is loose, the muffler may get loose during operation which may result in engine catching on fire.

■

SPARK ARRESTER

• The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet.

Periodically inspect and clean as necessary with a wire brush. In the

State of California it is required by law

(Section 4442 of the California Pulic

Resources Code) to equip a spark arrester when a gas powered tool is used in any forest covered, bush covered, or grass covered unimproved land.

(1) Spark Arrester

■

AIR INLET SCREEN

IMPORTANT

• Blowing air is taken in from the air inlet screen. When air flow has dropped down during operation, stop the engine and inspect the air inlet screen for blocking by obstacles.

• Note that failure to remove any such obstacles may result in the engine becoming overheated and damaged.

WARNING

Never use the blower without the screen at the air intake of the blower.

Before each use, check that, the screw

(1) is securely tightened and is free from any damage.

F14

HBZ2610

(1) Screw

(2) Air inlet screen

■

PROCEDURES TO BE PERFORMED

AFTER EVERY 50 HOURS OF USE

• Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time.

• Tighten all screws, bolts, and fittings.

U

S

US-13

HBZ2610

10. Storage

BEFORE STORING THE BLOWER:

1. Drain a fuel tank and push the primer bulb until it becomes empty of fuel.

2 .Remove the spark plug and drop a spoonful of 2-cycle oil into the cylider.

Crank the engine several time and install the spark plug.

3. Store unit in a dry, dust free place, out of the reach of children.

11. Disposal

• When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations.

12. Optional vacuum kit usage

• See the operating instructions included with the vacuum kit.

13. Troubleshooting guide

Case 1. Starting failure

CHECK

fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug

PROBABLE CAUSES

➞ incorrect fuel

➞ fuel filter is clogged

➞ out of normal range

➞ spark plug is fouled/wet

➞ plug gap is incorrect

➞ disconnected

ACTION

➞ drain it and with correct fuel

➞ clean

➞ adjust to normal range

➞ clean/dry

➞ correct (GAP: 0.6 – 0.7 mm)

➞ retighten

Case 2. Engine starts but does not keep running/Hard re-starting.

fuel tank carburetor adjustment screw muffler,cylinder (exhaust port) air cleaner

CHECK

cylinder fin, fan cover

PROBABLE CAUSES

➞ incorrect fuel or staled fuel

➞ out of normal range

➞ carbon is built-up

➞ clogged with dust

➞ clogged with dust

ACTION

➞ drain it and with correct fuel

➞ adjust to normal range

➞ wipe away

➞ wash

➞ clean

When your unit seems to need further service, please consult with our service shop in your area.

US-14

HBZ2610

FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY

STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS

The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment

Canada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and later small off-road engine. In U.S. and Canada, new equipment that use small off-road engines must be designed, built, and equipped to meet the applicable Federal or Californian stringent anti-smog standards. RedMax must warrant the emissions control system on your small off-road engine for the period listed below provided there has been no abuse, neglect or improper maintenance of your equipment. Your emissions control system may include parts such as carburetor, ignition system, catalytic converter, fuel tank, filters and other associated components. Also, included may be hoses, belts, connectors, sensors, and other emission-related assemblies.

Where a warrantable condition exists, RedMax will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVERAGE

This emissions control system is warranted for two years or if the product qualifies for a longer warranty period resulting from the type of use, that period shall prevail. If any emissions-related part on your equipment is defective, the part will be repaired or replaced by RedMax.

OWNER'S WARRANTY RESPONSIBILITIES

As the small off-road engine owner, you are responsible for performance of the required maintenance listed in your Owner's Manual. RedMax recommends that you retain all receipts covering maintenance on your small offroad engine, but RedMax cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance. As the small off-road engine owner, you should however be aware that the RedMax may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, or improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to a RedMax distribution center or service center as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty coverage, you should contact RedMax at 1-

800-291-8251 or via e-mail at [email protected].

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.

LENGTH OF COVERAGE

RedMax warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is designed, built, and equipped so as to conform with all applicable regulations adopted by EPA and CARB, and is free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

Repair or replacement of any warranted part under the warranty must be performed at no charge to the owner at a warranty station. Warranty services or repairs will be provided at all RedMax distribution centers that are franchised to service the subject engines. Throughout the emissions warranty period of two years, RedMax must maintain a supply of warranted parts sufficient to meet the expected demand for such parts.

WARRANTY PERIOD

Any warranted part that is scheduled for replacement as required in the maintenance schedule, is warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part will be repaired or replaced by RedMax at no cost.

Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first scheduled replacement point for the part. Any warranted part that is not scheduled for replacement as required in the maintenance schedule, is warranted for two years or if the product qualifies for a longer warranty period resulting from the type of use, that period shall prevail. If any such part fails during the period of warranty coverage, it will be repaired and replaced by RedMax at no cost. Any such part repaired or replaced under the

U

S

US-15

HBZ2610 warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regular inspection in the maintenance schedule will be warranted for a period of two years. A statement in such written instructions to the effect of "repair or replace as necessary" will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

DIAGNOSIS

The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station.

CONSEQUENTIAL DAMAGES

RedMax is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part.

EMISSION WARRANTY PARTS LIST

1. Air-induction system*

2. Fuel system*

3. Ignition system*

4. Fuel tank, cap and lines as applicable*

*some components only covered up to point specified by maintenance schedule

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD-ON OR MODIFIED PARTS

Add-on or modified parts that are not exempted by CARB or EPA may not be used. The use of any nonexempted add-on or modified parts will be grounds for disallowing a warranty claim. RedMax will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or contact RedMax at 1-800-291-8251 or via e-mail at [email protected].

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs are provided through all RedMax authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the warranty obligations of the manufacturer.

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator's manual.

US-16