Extech Instruments EX310 User manual

पीडीएफ

दस्तावेज़

User's Guide

Mini Multimeter with Non-Contact Voltage Detector (NCV)

Model EX310

Introduction

Congratulations on your purchase of the Extech EX310 MultiMeter. The EX310 offers AC/DC Voltage, AC/DC Current, Resistance, Diode, and Continuity testing plus a built-in non-contact Voltage Detector. Proper use and care of this meter will provide many years of reliable service.

Safety

WARNING

CAUTION

MAX

600V

This symbol adjacent to another symbol, terminal or operating device indicates that the operator must refer to an explanation in the Operating Instructions to avoid personal injury or damage to the meter.

This WARNING symbol indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.

This CAUTION symbol indicates a potentially hazardous situation, which if not avoided, may result damage to the product.

This symbol advises the user that the terminal(s) so marked must not be connected to a circuit point at which the voltage with respect to earth ground exceeds 600V.

This symbol adjacent to one or more terminals identifies them as being associated with ranges that may, in normal use, be subjected to particularly hazardous voltages. For maximum safety, the meter and its test leads should not be handled when these terminals are energized.

This symbol indicates that a device is protected throughout by double insulation or reinforced insulation.

2 Model EX310-EU-ENG – V7.2– 05/2008

SAFETY INSTRUCTIONS

This meter has been designed for safe use, but must be operated with caution.

The rules listed below must be carefully followed for safe operation.

1. NEVER apply voltage or current to the meter that exceeds the specified maximum:

Input Protection Limits

V DC or V AC mA AC/DC

A AC/DC

600V AC and DC

200mA DC/AC

10A DC/AC (for 30 seconds max. every 15 mins.)

250V DC/AC Resistance, Diode Test,

Continuity

2. USE EXTREME CAUTION when working with high voltages.

3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds 600V above earth ground.

4. NEVER connect the meter leads across a voltage source while the function switch is in the current, resistance, or diode mode. Doing so can damage the meter.

5. ALWAYS discharge filter capacitors in power supplies and disconnect the power when making resistance or diode tests.

6. ALWAYS turn off power and disconnect test leads before opening the covers to replace the fuse or battery.

7. NEVER operate the meter unless the back cover and the battery and fuse covers are in place and fastened securely.

8. If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

3 Model EX310-EU-ENG – V7.2– 05/2008

CAUTIONS

• Improper use of this meter can cause damage, shock, injury or death.

Read and understand this user manual before operating the meter.

• Always remove the test leads before replacing the battery or fuses.

• Inspect the condition of the test leads and the meter itself for any damage before operating the meter.

• Use great care when making measurements if the voltages are greater than 25VAC rms or 35VDC. These voltages are considered a shock hazard.

• Always discharge capacitors and remove power from the device under test before performing Diode, Resistance or Continuity tests.

• Voltage checks on electrical outlets can be difficult and misleading because of the uncertainty of connection to the recessed electrical contacts. Other means should be used to ensure that the terminals are not "live".

• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

• This device is not a toy and must not reach children’s hands. It contains hazardous objects as well as small parts that the children could swallow.

In case a child swallows any of them, please contact a physician immediately

• Do not leave batteries and packing material lying around unattended; they can be dangerous for children if they use them as toys

• In case the device is going to be unused for an extended period of time, remove the batteries to prevent them from training

• Expired or damaged batteries can cause cauterization on contact with the skin. Always, therefore, use suitable hand gloves in such cases

• See that the batteries are not short-circuited. Do not throw batteries into the fire.

4 Model EX310-EU-ENG – V7.2– 05/2008

Controls and Jacks

1. AC Voltage Detector Sensor

2. AC Voltage Detector indicator light

3. LCD

4. Non-contact AC Voltage Detector test button

5. Rotary function dial

6. 10 ampere test lead jack

7. COM test lead jack

8. Test lead jack for voltage, milliamp, resistance/continuity, and diode functions

9. Protective rubber holster (must be removed to access the rear battery compartment)

Symbols

•))) Continuity

Diode

Battery status

V Volts

A Amps

Ohms

5 Model EX310-EU-ENG – V7.2– 05/2008

Operating Instructions

WARNING

: Risk of electrocution. High-voltage circuits, both AC and DC, are very dangerous and should be measured with great care.

NOTE

: On some low AC and DC voltage ranges, with the test leads not connected to a device, the display may show a random, changing reading.

This is normal and is caused by the high-input sensitivity. The reading will stabilize and give a proper measurement when connected to a circuit.

NON-CONTACT AC VOLTAGE DETECTOR

The EX310 can detect the presence of AC voltage (from 100 to 600VAC) simply by being held very near to a voltage source.

WARNING

: Test the AC voltage detector on a known live circuit before each use.

WARNING

: Before using the meter in the AC Voltage Detector mode, verify that the battery is fresh by confirming characters appear on the LCD when the function dial is turned to any position. Do not attempt to use the meter as an AC

Voltage Detector if the battery is weak or bad.

NON-CONTACT VOLTAGE (NCV)

The NCV function works on any rotary switch position.

1. Test the detector on a known live circuit before use.

2. Press and hold the NCV button for the duration of the test. The meter will beep once when the button is pushed.

3. Hold the top of the meter very close to the voltage source as shown.

4. If voltage is present, the rim of the LCD display will flash a bright orange and an audible warning will sound.

6 Model EX310-EU-ENG – V7.2– 05/2008

AC VOLTAGE MEASUREMENTS

WARNING:

Risk of Electrocution. The probe tips may not be long enough to contact the live parts inside some 240V outlets for appliances because the contacts are recessed deep in the outlets. As a result, the reading may show

0 volts when the outlet actually has voltage on it. Make sure the probe tips are touching the metal contacts inside the outlet before assuming that no voltage is present.

CAUTION:

Do not measure AC voltages if a motor on the circuit is being switched ON or OFF. Large voltage surges may occur that can damage the meter.

1. Set the function switch to the 600 VAC position.

2. Insert the black test lead banana plug into the negative COM jack. Insert red test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the neutral side of the circuit.

4. Touch the red test probe tip to the “hot” side of circuit.

5. Read the voltage in the display.

DC VOLTAGE MEASUREMENTS

CAUTION:

Do not measure DC voltages if a motor on the circuit is being switched ON or OFF. Large voltage surges may occur that can damage the meter.

1. Set the function switch to the highest VDC position.

2. Insert the black test lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit.

4. Read the voltage in the display. Move the function switch to successively lower VDC positions to obtain a higher resolution reading.

7 Model EX310-EU-ENG – V7.2– 05/2008

BATTERY VOLTAGE TEST

CAUTION:

Do not measure batteries while they are installed in the devices they are powering. The batteries must be removed from installations before tests can be made.

1. Set the function switch to the 1.5V or 9V

BAT

switch position. Use the 1.5V position for ‘AAA’, ‘AA’, ‘C’, ‘D’, and other 1.5V batteries. Use the 9V position for square 9V transistor batteries.

2. Insert the black test lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the negative side of the battery. Touch the red test probe tip to the positive side of the battery.

4. Read the voltage in the display.

AC / DC CURRENT MEASUREMENTS

CAUTION:

Do not make current measurements at 10 Amps for longer than

30 seconds. Exceeding 30 seconds may cause damage to the meter and/or the test leads.

1. Insert the black test lead banana plug into the negative COM jack.

2. For current measurements up to 200mA AC or DC, set the function switch to the 200m AAC or ADC position and insert the red test lead banana plug into the mA jack.

3. For current measurements up to 10A AC or DC, set the function switch to the 10A AAC or 10A ADC position and insert the red test lead banana plug into the 10A jack.

4. Remove power from the circuit under test, then open up the circuit at the point where you wish to measure current.

5. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit.

6. Apply power to the circuit.

7. Read the current in the display.

8 Model EX310-EU-ENG – V7.2– 05/2008

RESISTANCE MEASUREMENTS

WARNING:

To avoid electric shock, disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements.

1. Set the function switch to the highest

Ω position.

2. Insert the black test lead banana plug into the negative COM jack.

3. Insert the red test lead banana plug into the positive

Ω jack.

4. Touch the test probe tips across the circuit or part under test. It is best to disconnect one side of the part under test so the rest of the circuit will not interfere with the resistance reading.

5. Read the resistance in the display. Move the function switch to successively lower

Ω positions to obtain a higher resolution reading.

CONTINUITY CHECK

WARNING:

To avoid electric shock, never measure continuity on circuits that have a voltage potential.

1. Set the function switch to the position.

2. Insert the black lead banana plug into the negative COM jack.

3. Insert the red test lead banana plug into the positive

Ω jack.

4. Touch the test probe tips to the circuit or wire you wish to check.

5. If the resistance is less than approximately 100

Ω, the audible signal will sound. If the circuit is open, the display will indicate “1___”.

9 Model EX310-EU-ENG – V7.2– 05/2008

DIODE TEST

1. Set the function switch to the position.

2. Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive jack.

3. Touch the test probes to the diode under test.

4. A good diode will indicate approx. 700 ohms for the forward test and “1___” for the reverse test.

5. A shorted diode will indicate the same value of resistance in both the reverse and forward test directions. An open diode will indicate “1___” in both test directions.

10 Model EX310-EU-ENG – V7.2– 05/2008

Maintenance

WARNING

: To avoid electric shock, disconnect the test leads from any source of voltage before removing the back cover or the battery or fuse covers.

WARNING:

To avoid electric shock, do not operate your meter until the battery and fuse covers are in place and fastened securely.

This MultiMeter is designed to provide years of dependable service, if the following care instructions are performed:

KEEP THE METER DRY

. If it gets wet, wipe it off.

USE AND STORE THE METER IN NORMAL TEMPERATURES.

Temperature extremes can shorten the life of the electronic parts and distort or melt plastic parts.

HANDLE THE METER GENTLY AND CAREFULLY.

Dropping it can damage the electronic parts or the case.

KEEP THE METER CLEAN.

Wipe the case occasionally with a damp cloth. DO NOT use chemicals, cleaning solvents, or detergents.

USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND

TYPE.

Remove old or weak batteries so they do not leak and damage the unit.

IF THE METER IS TO BE STORED FOR A LONG PERIOD OF TIME

, the battery should be removed to prevent damage to the unit.

11 Model EX310-EU-ENG – V7.2– 05/2008

BATTERY INSTALLATION and LOW BATTERY INDICATION

WARNING

: To avoid electric shock, disconnect the test leads from any source of voltage before removing the battery cover. Do not operate meter unless the battery is in place.

LOW BATTERY INDICATION

The icon will appear in the lower left-hand corner of the display when the battery voltage becomes low. Replace the batteries when this appears.

BATTERY REPLACEMENT

1. Disconnect the test leads from the meter.

2. Remove the protective rubber holster. See diagram.

3. Remove the Phillips head screw located on the lower back of the instrument.

4. Remove the fuse/battery compartment cover to access the battery. See diagram.

5. Replace the 9V battery observing polarity.

6. Secure the fuse/battery compartment cover using the Phillips head screw.

7. Place the protective rubber holster on the meter.

You, as the end user, are legally bound (Battery ordinance) to return all used batteries and accumulators; disposal in the

household garbage is prohibited!

You can hand over your used batteries / accumulators, gratuitously, at the collection points for our branches in your community or wherever batteries / accumulators are sold!

Disposal

Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle

12 Model EX310-EU-ENG – V7.2– 05/2008

1. Removable Rubber Holster

2. Meter

3. Battery

4. Fuses

REPLACING THE FUSES

WARNING

: To avoid electric shock, disconnect the test leads from any source of voltage before removing the fuse cover.

1. Disconnect the test leads from the meter.

2. Remove the protective rubber holster.

3. Remove the Phillips head screw located on the lower back of the instrument.

4. Remove the fuse/battery compartment cover to access the fuses.

5. Gently remove the fuse(s) and install new fuse(s) into the holder(s).

6. Always use fuses of the proper size and value (200mA/250V fast blow for the mA / µA ranges, 10A/250V fast blow for the A range).

7. Secure the fuse/battery compartment cover.

8. Place the protective rubber holster on the meter.

WARNING

: To avoid electric shock, do not operate your meter until the fuse cover is in place and fastened securely.

13 Model EX310-EU-ENG – V7.2– 05/2008

Range Specifications

Non-contact

AC Voltage detector

100 to 600V Resolution & accuracy do not apply since the meter does not display the voltage in this mode.

The lamp at the top of the meter’s display flashes when voltage is sensed and an audible warning will sound

200mV 0.1mV ±(0.5% reading + 2 digits) DC Voltage

(V DC)

2000mV 1mV

20V 0.01V

±(1.0% reading + 2 digits)

200V 0.1V

600V 1V

±(1.5% reading + 2 digits)

200V 0.1V

±(1.5% reading + 3 digits)

600V 1V

±(2.0% reading + 4 digits

AC Voltage

(VAC)

50/60Hz

DC Current

(A DC)

200mA 0.1mA

±(1.5% reading + 2 digits)

10A 0.01A

±(2.5% reading + 5 digits)

AC Current

Resistance

200mA 0.1mA ±(1.8% reading + 5 digits)

(A AC)

50/60Hz

10A 0.01A ±(3.0% reading + 7 digits)

200

Ω 0.1Ω ±(1.2% reading + 4 digits)

2000

20k

Ω 0.01kΩ

200k

Ω 0.1kΩ

2000k

Ω 1kΩ

±(1.2% reading + 2 digits)

14 Model EX310-EU-ENG – V7.2– 05/2008

General Specifications

Diode Test

Continuity Check

Bias voltage: 2.3VDC

Audible signal will sound if the resistance is less than 100

Input Impedance

1MΩ (VDC & VAC)

AC Bandwidth

50 / 60Hz

Display

2000 count (0 to 1999) LCD

Overrange indication

displayed

Polarity

Measurement Rate

Storage Humidity

Operating Altitude

Automatic (no indication for positive); Minus (-

) sign for negative

2 times per second, nominal

Low Battery Indication

Battery

Fuses

Operating Humidity

“ ”

is displayed if battery voltage drops below operating voltage

One (1) 9V battery mA range; 200mA/250V fast blow

A range; 10A/250V fast blow, ceramic

Operating Temperature

32ºF to 122ºF (0ºC to 50ºC)

Storage Temperature

-4 o

F to 140 o

F (-20 o

C to 60 o

Max 70% up to 87ºF (31ºC) decreasing linearly to 50% at 122ºF (50ºC)

< 80% RH

7000 ft. (2000 meters) maximum.

Weight

Size

Approvals

Safety

Section 1.01

9.17 oz (260g) includes holster

5.8” x 2.9” x 1.6” (147 x 76 x 42mm) includes holster

CE, UL

This meter is intended for indoor use and protected, against the users, by double insulation per EN61010-1 and IEC61010-1

2nd Edition (2001) to CAT II 1000V & CAT III

600V; Pollution Degree 2. The meter also meets UL 61010-1, Second Edition (2004),

CAN/CSA C22.2 No. 61010-1, Second Edition

(2004), and UL 61010B-2-031, First Edition

(2003)

UL LISTED

The UL mark does not indicate that this product has been evaluated for the accuracy of its readings.

15 Model EX310-EU-ENG – V7.2– 05/2008

PER IEC1010 OVERVOLTAGE INSTALLATION CATEGORY

OVERVOLTAGE CATEGORY I

Equipment of OVERVOLTAGE CATEGORY I is equipment for connection to circuits in which measures are taken to limit the transient overvoltages to an appropriate low level. Note – Examples include protected electronic circuits.

OVERVOLTAGE CATEGORY II

Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be supplied from the fixed installation.

Note – Examples include household, office, and laboratory appliances.

OVERVOLTAGE CATEGORY III

Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.

Note – Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed installation.

OVERVOLTAGE CATEGORY IV

Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation.

Note – Examples include electricity meters and primary over-current protection equipment

more infor for Extech EX310

Phone: 01235 838 555

Email: [email protected]

Web. www.airconcern.co.uk

Air Concern Ltd, Building 173 Curie Avenue Harvell Didcot, Oxfordshire

नमस्ते! मैं एक एआई चैटबॉट हूं जिसे विशेष रूप से Extech Instruments EX310 User manual के साथ आपकी सहायता करने के लिए प्रशिक्षित किया गया है. मैंने दस्तावेज़ की अच्छी तरह से समीक्षा की है और आपको आवश्यक सटीक जानकारी का पता लगाने या स्पष्ट और सरल शब्दों में सामग्री को समझाने में मदद कर सकता हूं. चाहे आप विशिष्ट सुविधाओं, समस्या निवारण चरणों या सामान्य उपयोग पर मार्गदर्शन की तलाश कर रहे हों, अपने प्रश्न पूछने के लिए स्वतंत्र महसूस करें. आप अपनी चिंताओं या जरूरतों के बारे में जितनी अधिक जानकारी प्रदान करेंगे, उतनी ही सटीक और प्रभावी ढंग से मैं आपकी सहायता कर सकता हूं!