advertisement
PAR 2 RGBW Zoom
User Manual
Professional Entertainment Technology
© 2013-2014 Martin Professional. Information subject to change without notice. Martin
Professional and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this manual. The Martin logo, the RUSH by Martin logo, the RUSH by Martin name, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional or its affiliates or subsidiaries.
Martin Professional • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark • www.martin.com
Manual: Revision C
Table of contents
Safety information ............................................................................................. 4
Introduction ....................................................................................................... 8
Before using the product for the first time ..................................................... 8
Physical installation .......................................................................................... 8
Fastening the fixture to a flat surface ............................................................ 9
Mounting the fixture on a truss ...................................................................... 9
Securing with a safety cable ......................................................................... 9
AC power ........................................................................................................ 10
Linking fixtures to power in a chain ............................................................. 11
Fixture overview .............................................................................................. 12
Control data link .............................................................................................. 13
Tips for reliable data transmission .............................................................. 13
Connecting the DMX data link ..................................................................... 14
Fixture setup ................................................................................................... 14
Using the control menus ............................................................................. 14
DMX function settings ................................................................................. 15
Dimming curves ........................................................................................... 16
Blackout or Hold if DMX signal stops .......................................................... 16
Display panel backlight sleep mode ............................................................ 17
White balance adjustment ........................................................................... 17
Fixture test ................................................................................................... 17
Stand-alone scene ...................................................................................... 18
Fixture information....................................................................................... 18
Reset ........................................................................................................... 19
Effects ............................................................................................................. 20
Maintenance ................................................................................................... 22
Cleaning ...................................................................................................... 22
Fuse replacement........................................................................................ 23
Service and repairs ..................................................................................... 23
DMX protocol .................................................................................................. 24
5-channel mode ........................................................................................... 24
9-channel mode ........................................................................................... 24
Control menus ................................................................................................. 26
Troubleshooting .............................................................................................. 27
Specifications .................................................................................................. 28
Safety information
WARNING!
Read the safety precautions in this manual before installing,
powering, operating or servicing this product.
The following symbols are used to identify important safety information on the product and in this manual:
Warning!
Safety hazard.
Risk of severe injury or death.
Warning!
LED light emission. Risk of eye injury.
Warning!
Refer to manual before installing, powering or servicing.
Warning!
Hazardous voltage. Risk of lethal or severe electric shock.
Warning!
Hot surfaces and fire hazard.
Risk Group 2 LED product according to EN 62471. Do not view the light output with optical instruments or any device that may concentrate the beam.
This product is for professional use only. It is not for household use. It product presents risks of severe injury or death due to fire hazards, electric shock and falls.
Respect all locally applicable laws, codes and regulations when installing, powering, operating or servicing the fixture.
Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture. Keep this manual for future use. If you have questions about how to operate the fixture safely, please contact your RUSH by Martin™ dealer or call the Martin™ 24-hour service hotline on +45 8740
0000, or in the USA on 1-888-tech-180.
For the latest user documentation and other information about this and all Martin™ products, please visit the Martin website at http://www.martin.com
4 RUSH PAR 2 RGBW Zoom User Manual
Protection from electric shock
Do not expose the fixture to rain or moisture.
Shut down power to the fixture before carrying out any installation or maintenance work and when the fixture is not in use.
Ensure that the fixture is electrically connected to ground
(earth).
Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault
(earth-fault) protection.
Socket outlets or external power switches used to supply the fixture with power must be located near the fixture and easily accessible so that the fixture can easily be disconnected from power.
Replace defective fuses with ones of the specified type and rating only.
Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs have been completed
Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices.
Use only Neutrik PowerCon cable connectors to connect to the fixture’s power sockets.
Do not connect devices to power in a chain that will exceed the electrical ratings of any cable or connector used in the chain.
The supplied power input cable is rated 6 A and can safely supply only one fixture with mains power. Do not connect any device to the fixture’s MAINS OUT connector when using this cable. If you replace this cable and also use the replacement cable to supply only one fixture with mains power, the replacement cable must also be rated 6 A minimum, have three conductors 18 AWG or 0.75 mm² minimum conductor size, have an outer cable diameter of 6 - 15 mm (0.2 - 0.6 in.) and be temperature-rated to suit the application. In the USA and
Canada the cable must be UL listed, type SJT or equivalent. In the EU the cable must be type H05VV-F or equivalent.
To connect fixtures to mains power in a chain, you must first
RUSH PAR 2 RGBW Zoom User Manual 5
6 obtain 12 AWG or 2.5 mm 2 power input and throughput cables that are 16 A rated and temperature-rated to suit the application.
In the USA and Canada the cables must be UL-listed, type SJT or equivalent. In the EU the cables must be type H05VV-F or equivalent. Suitable cables with Neutrik PowerCon connectors are available from Martin™ (see Accessories on page 29). If you use these cables, you can connect fixtures to power in a linked chain, MAINS OUT throughput socket to MAINS IN input socket, but do not link more than:
• eight (8) RUSH PAR 2 fixtures in total at 100-120 V, or
• eighteen (18) RUSH PAR 2 fixtures in total at 200-240 V.
The voltage and frequency at the MAINS OUT socket are the same as the voltage and frequency applied to the MAINS IN socket. Only connect devices to the MAINS OUT socket that accept this voltage and frequency.
Protection from burns and fire
Do not operate the fixture if the ambient temperature (T a exceeds 40° C (104° F).
)
The surface of the product casing can reach up to 85° C
(185° F) during operation. Avoid contact by persons and materials. Allow the fixture to cool for at least 15 minutes before handling.
Keep flammable materials well away from the fixture. Keep all combustible materials (e.g. fabric, wood, paper) at least 200 mm
(8 in.) away from the fixture housing.
Ensure that there is free and unobstructed airflow around the fixture. Provide a minimum clearance of 100 mm (4 in.) around fans and air vents.
Do not illuminate surfaces within 200 mm (8 in.) of the fixture.
Do not attempt to bypass thermostatic switches or fuses.
Do not stick filters, masks or other materials onto any optical component.
Protection from eye injury
Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may concentrate the light output.
RUSH PAR 2 RGBW Zoom User Manual
Protection from injury
Fasten the fixture securely to either a fixed surface or fixed structure when in use. The fixture is not portable when installed.
Ensure that any supporting structure and/or hardware used can hold at least 10 times the weight of all the devices they support.
If suspending from a rigging structure, fasten the fixture to a rigging clamp. Do not use safety cables as the primary means of support.
If the fixture is installed in a location where it may cause injury or damage if it falls, install as directed in this manual a secondary attachment such as a safety cable that will hold the fixture if a primary attachment fails. The secondary attachment must be approved by an official body such as TÜV as a safety attachment for the weight that it secures, must comply with EN
60598-2-17 Section 17.6.6 and must be capable of bearing a static suspended load that is ten times the weight of the fixture and all installed accessories.
Check that all external covers and rigging hardware are securely fastened.
Block access below the work area and work from a stable platform whenever installing, servicing or moving the fixture.
Do not operate the fixture with missing or damaged covers, shields or any optical component.
In the event of an operating problem, stop using the fixture immediately and disconnect it from power. Do not attempt to use a fixture that is obviously damaged.
Do not modify the fixture or install other than genuine RUSH by
Martin™ parts.
Refer any service operation not described in this manual to a qualified technician.
RUSH PAR 2 RGBW Zoom User Manual 7
Introduction
The RUSH PAR 2 RGBW Zoom™ is a bright single-lens LED PAR Can with fully premixed color from 12 RGBW LEDs and a 10 to 60° motorized zoom. It offers electronic dimming and strobe and comes with a flexible bracket for floor or truss mounting.
The PAR 2 RGBW Zoom can be controlled using any DMX-compliant controller. The fixture is supplied with a 1.5 m (5 ft) power cable (local power plug not included) and a mounting bracket with two legs.
Before using the product for the first time
1. Read Safety information on page 4 before installing, powering, operating or servicing the fixture.
2. Unpack and ensure that there is no transportation damage before using the fixture. Never attempt to operate a damaged fixture.
3. If the fixture is not going to be hard-wired to an AC mains power source, install a local power plug (not supplied) on the end of the supplied power cable.
4. Before operating, ensure that the voltage and frequency of the local power source match the mains power requirements of the fixture.
5. Check the Martin Professional website at www.martin.com for the most recent user documentation and technical information about the fixture.
RUSH by Martin™ user manual revisions are identified by the revision letter at the bottom of the inside cover.
When the fixture is powered on for the first time, it may smoke slightly as it warms up, but this will only last a few minutes and is no cause for concern.
Physical installation
Read ‘Safety information’ on page 4 before installing the fixture.
The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation. Ensure that none of the fixture’s ventilation slots are blocked and ensure that the product is fastened to a secure structure or surface.
8 RUSH PAR 2 RGBW Zoom User Manual
Fastening the fixture to a flat surface
The fixture can be fastened to a hard, fixed, flat surface that is oriented at any angle. Ensure that the surface can support at least 10 times the weight of all fixtures and equipment to be installed on it.
Fasten the fixture securely. Do not stand it on a surface or leave it where it can be moved or fall over. If you install the fixture in a location where it may fall and cause injury or damage if the primary attachment fails, secure it as directed below with a securely anchored safety cable that will hold the fixture if the primary fastening method fails.
Mounting the fixture on a truss
The fixture can be clamped to a truss or similar rigging structure in any orientation. When installing the fixture hanging vertically down, you can use an open-type clamp such as a G-clamp. When installing in any other orientation, you must use a half-coupler clamp (see illustration on right) that completely encircles the truss chord.
To clamp the fixture to a truss:
1. Check that the rigging structure can support at least 10 times the weight of all fixtures and equipment to be installed on it.
2. Block access under the work area.
3. Fold the legs of the mounting bracket together and bolt a rigging clamp securely to the mounting bracket. The bolt used must be M12, grade 8.8 steel minimum. It must pass through both mounting bracket legs and be fastened with a self-locking nut.
4. Working from a stable platform, hang the fixture with its clamp on the truss and fasten the clamp securely.
5. Secure the fixture with a safety cable as directed below.
Securing with a safety cable
Secure the fixture with a safety cable (or other secondary attachment) that is approved for the weight of the fixture so that the safety cable will hold the fixture if a primary attachment fails. Loop the cable through one of the safety cable attachment points on the fixture (see arrows in illustration on right) and around a secure anchoring point.
RUSH PAR 2 RGBW Zoom User Manual 9
AC power
Read Safety information on page 4 before connecting the fixture to AC mains power.
Warning! The mains power input cable supplied with the fixture is rated 6 A and can supply only one fixture with mains power.
Do not connect any device to the fixture’s MAINS OUT power throughput socket when using this input cable. If you want to connect other fixtures to the MAINS OUT socket, see ‘Linking fixtures to power in a chain’ on page 11.
For protection from electric shock, the fixture must be grounded
(earthed). The power distribution circuit must be equipped with a fuse or circuit breaker and ground-fault (earth-fault) protection.
Socket outlets or external power switches used to supply the fixture with power must be located near the fixture and easily accessible so that the fixture can easily be disconnected from power.
Do not insert or remove live Neutrik PowerCon connectors to apply or cut power, as this may cause arcing at the terminals that will damage the connectors.
Do not use an external dimming system to supply power to the fixture, as this may cause damage to the fixture that is not covered by the product warranty.
Power input and throughput cables must be rated 16 A minimum, have three conductors 1.5 mm² (16 AWG) minimum conductor size and an outer cable diameter of 5 - 15 mm (0.2 - 0.6 in.). The cables must be hard usage type
(SJT or equivalent) and heat-resistant to 90° C (194° F) minimum. In the EU the cables must be HAR approved or equivalent.
The fixture can be hard-wired to a building electrical installation if you want to install it permanently, or a power plug (not supplied) that is suitable for the local power outlets can be installed on the supplied power cable.
If you install a power plug on the power cable, follow the plug manufacturer’s instructions and connect the wires in the power cable as shown in this table:
US system
EU system
Earth, Ground or Neutral or N Live or L
Yellow/green Blue Brown
The fixture has an auto-ranging power supply that accepts AC mains power at
100-240 V at 50/60 Hz. Do not apply AC mains power at any other voltage or
10 RUSH PAR 2 RGBW Zoom User Manual
frequency to the fixture.
Linking fixtures to power in a chain
If you obtain a 12 AWG or 2.5 mm
2
power input cable and 12 AWG or 2.5 mm throughput cables from Martin™ (see Accessories on page 29), you can relay mains power from one fixture to another by connecting fixtures to power in a linked daisy-chain, MAINS OUT throughput socket to MAINS IN input socket.
2
Using 12 AWG or 2.5mm
2
cables from Martin™, you can link:
• Maximum eight (8) RUSH PAR 2 RGBW Zoom fixtures in total at 100-120
V, or
• Maximum eighteen (18) RUSH PAR 2 RGBW Zoom fixtures in total at
200-240 V.
RUSH PAR 2 RGBW Zoom User Manual 11
Fixture overview
1 - Display
2 - LEDs
The two LEDs on the rear of the fixture have the following functions:
POWER On
DMX On Valid DMX signal present
3 - Buttons
MENU
• Activate the menu, or
• Return to the previous level of the menu structure, or
• Press and hold to exit the menus
DOWN Go down a menu level
UP Go up a menu level
ENTER Confirm the selected function
4 – 5-pin XLR DMX input/output sockets
12 RUSH PAR 2 RGBW Zoom User Manual
5 – Primary (mains power) fuse F1
The T 6.3A fixture fuse is located in a fuse holder next to the power input/output connectors.
6 – AC mains power IN
A blue Neutrik PowerCon socket is provided to connect the fixture to AC mains power.
7 – AC mains power OUT (THRU)
See Safety information on page 4. The light-grey Neutrik PowerCon socket can be used to supply power to other fixtures only if the supplied power input cable is replaced as directed in this manual and safety limits are respected.
Control data link
A DMX 512 data link is required in order to control the fixture via DMX. The fixture has 5-pin XLR connectors for DMX data input and output.
The number of daisy-chained fixtures is limited by the number of DMX channels required by the fixtures in relation to the maximum 512 channels available in one DMX universe. Note that if independent control of a fixture is required, it must have its own DMX channels. Fixtures that are required to behave identically can share the same DMX address and channels. To add more fixtures or groups of fixtures when the above limit is reached, add a DMX universe and another daisy-chained link.
Tips for reliable data transmission
Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit control data reliably over long runs. 24
RUSH PAR 2 RGBW Zoom User Manual 13
AWG cable is suitable for runs up to 300 meters (1000 ft.). Heavier gauge cable and/or an amplifier is recommended for longer runs. The pinout on all connectors is pin 1 = shield, pin 2 = cold (-), and pin 3 = hot (+). Pins 4 and 5 in the 5-pin XLR connectors are not used in the fixture but are available for possible additional data signals as required by the DMX512-A standard.
Standard pinout is pin 4 = data 2 cold (-) and pin 5 = data 2 hot (+).
To split the link into branches, use a splitter such as the Martin 4-Channel
Opto-Isolated RS-485 Splitter/Amplifier.
Terminate the link by installing a DMX termination plug in the output socket of the last fixture. The termination plug, which is a male XLR plug with a 120
Ohm, 0.25 W resistor soldered between pins 2 and 3, “soaks up” the control signal so it does not reflect and cause interference. If a splitter is used, terminate each branch of the link.
Connecting the DMX data link
To connect the fixture to data:
1. Connect the DMX data output from the controller to the first fixture’s male
XLR DMX input connector.
2. Connect the first fixture’s DMX output to the DMX input of the next fixture and continue connecting fixtures output to input. Terminate the last fixture on the link with a DMX termination plug.
Fixture setup
This section explains the fixture characteristics that can be set to determine how it can be controlled and will behave. These settings are made using the menus available in the control panel. Settings are retained in memory when the fixture is powered off.
A complete map of the control menu structure and brief explanations of their purposes can be found in ‘Control menus’ on page 26.
Using the control menus
To access the control menus or to return to the next highest level in the menu structure, press the MENU button. Navigate the menu structure using the
DOWN, UP and ENTER buttons. If you have selected a menu option, confirm your selection and set that option using the ENTER button, or if you want to return to the next highest level in the menu structure without making a change, press the MENU button.
To exit the menus, press and hold the MENU button.
14 RUSH PAR 2 RGBW Zoom User Manual
DMX function settings
DMX function settings include the DMX address and DMX control mode.
DMX addressing
The DMX address, also known as the start channel, is the first channel used to receive instructions from a DMX controller. The fixture can be controlled using signals sent by a DMX controller over a different number of channels depending on which DMX mode it is set to.
For example:
• In 5-channel mode, if the first fixture has a DMX address of 1, then DMX address 6 is available for the next fixture, address 11 for the next fixture and so on.
• In 9-channel mode, if the first fixture has a DMX address of 1, then DMX address 10 is available for the next fixture, address 19 for the next fixture and so on.
For independent control, each fixture must be assigned its own control channels. Two fixtures of the same type may share the same address, if identical behavior is desired. Address sharing can be useful for diagnostic purposes and grouped control.
To set the fixture’s DMX address:
1. In the fixture’s control panel, use the UP and DOWN buttons to select
DMX ADDRESS and press ENTER. The fixture’s currently set DMX address will blink in the display.
2. Use the UP and DOWN buttons to select a new address.
3. Once the new address has been selected, press ENTER to confirm it (or to return to the higher level of the menu structure without making a change, press MENU).
DMX channel modes
The fixture provides two control modes enabling varying degrees of DMX control and enabling the efficient use of DMX channel bandwidth. For the effects available and control details, see ‘DMX protocol’ on page 24. The different modes are:
5-channel mode – Individual control of red, green, blue and white channels for color mixing plus zoom.
9-channel mode – Full-range dimming with 16-bit fine control, shutter/strobe effects, individual control of red, green, blue and white channels for color mixing, ‘color wheel’ effect and zoom.
To set a fixture’s DMX channel mode:
1. Select CHANNEL MODE and press ENTER.
RUSH PAR 2 RGBW Zoom User Manual 15
2. Use the DOWN and UP buttons to select the desired DMX mode and press ENTER to set (or, to return to the higher level of the menu structure without making a change, press MENU).
Dimming curves
Four dimming curves are available:
DIMMER 1: LINEAR – The increase in light intensity appears to be linear as DMX value is increased.
DIMMER 2: SQUARE LAW – light intensity control is finer at low levels and coarser at high levels.
DIMMER 3: INVERSE SQUARE LAW – light intensity control is coarser at low levels and finer at high levels.
DIMMER 4: S-CURVE – light intensity control is finer at low levels and high levels and coarser at medium levels.
DIMMER 1 DIMMER 2 DIMMER 3 DIMMER 4
To set the fixture’s dimming curve:
1. Select DIMMER and press ENTER. The currently set mode will blink in the display.
2. Use the DOWN and UP buttons to select DIMMER1, DIMMER 2, DIMMER
3, or DIMMER 4.
3. Once the mode has been selected, press ENTER to set (or, to return to the higher level of the menu structure without making a change press
MENU).
Blackout or Hold if DMX signal stops
You can decide how the fixture should behave if you are controlling the fixture via DMX and you stop sending the DMX signal.
1. Select BLACKOUT and press ENTER. The currently set blackout mode will blink in the display.
2. Using the DOWN and UP buttons, select YES or HOLD to decide how the fixture should respond if it stops receiving a DMX signal:
-
If you select YES, the fixture will black out
-
If you select HOLD, the fixture will continue to show the effect that it is displaying at the time.
16 RUSH PAR 2 RGBW Zoom User Manual
3. Press ENTER to confirm your choice (or, to return to the higher level of the menu structure without making a change press MENU).
Display panel backlight sleep mode
To set the display panel backlight to remain on all the time or to automatically switch off when the control panel is not in use:
1. Select BACKLIGHT and press ENTER.
2. Use the DOWN and UP buttons to select ON (display backlight constantly on) or OFF (display backlight turns off when not in use). Press ENTER to confirm (or, to return to the higher level of the menu structure without making a change, press MENU).
White balance adjustment
You can adjust the white balance of the fixture (to match other fixtures, for example) by adjusting the amount of red, green or blue in the white output. To adjust the white balance mix:
1. Select WHITE BALANCE and press ENTER.
2. Use the DOWN and UP buttons to select RED or GREEN or BLUE.
3. Press ENTER to confirm.
4. Use the DOWN and UP buttons to change the value (125-255).
5. Once the correct value has been selected, press ENTER to confirm (or, to return to the higher level of the menu structure without making a change, press MENU).
Fixture test
Automatic tests of all effects or manual test of individual effects can be run from the control menus.
Automatic effects test
To perform a complete test of all of the fixture’s effects:
1. Select FIXTURE TEST and press ENTER to confirm. The automatic test will run.
2. To stop the test and return to a higher level of the menu structure, press
MENU.
Manual effects test
The Manual effects test menu can be used to test the fixture’s effects individually and to set a standalone scene that the fixture will show each time it is powered on:
1. Select MANUAL TEST and press ENTER.
RUSH PAR 2 RGBW Zoom User Manual 17
2. Use the DOWN and UP buttons to select an effect: dimmer, red, green, blue, white, color wheel, shutter or zoom. Press ENTER to confirm your selection.
3. Use the DOWN and UP buttons to change the value (000-255). The test will be the equivalent of sending this DMX value to the selected effect.
4. Press ENTER to confirm your selection and activate the effect (or, to return to the higher level of the menu structure without making a change, press MENU).
5. If you have confirmed a selection with the ENTER button, press MENU to return to the list of effects.
6. If you want, you can now select another effect and set a value for it as described above. This effect will be added to the effects that you have already set.
By combining effects in this way, you can set a mix of RGBW colors plus a strobe, for example.
Note that if you set a color wheel effect, you override any RGBW values that have been set. If you set an RGBW color, you override any color wheel value that has been set.
Stand-alone scene
If you power the fixture off while it is running the effect – or the combination of effects – that you have set in the MANUAL TEST menu (see above), it will hold that setting in memory. The next time you power the fixture on, it will display those effects. This feature lets you set a stand-alone scene that runs automatically each time the fixture is powered on.
Note that when the fixture is running a stand-alone scene, it will not respond to
DMX control signals.
Fixture information
Fixture temperature readout
To check the onboard temperature of the fixture:
1. Select TEMP and press ENTER. The display will show the temperature of the unit.
2. To return to a higher level of the menu structure, press MENU.
Fixture operating time
The fixture operating time counter monitors the total number of hours the fixture has been in operation since manufacture. To display the counter:
1. Select FIXTURE TIME and press ENTER. The display will show the time the unit has been running.
2. To return to a higher level of the menu structure, press MENU.
18 RUSH PAR 2 RGBW Zoom User Manual
Firmware version
To see which software version is installed in the fixture:
1. Select FIXTURE VERSION and press ENTER. The firmware version will be shown.
2. To return to a higher level of the menu structure, press MENU.
Reset
To reset the fixture to its factory default settings:
1. Select RESET and press ENTER to confirm.
2. The fixture will now reset to its default settings.
RUSH PAR 2 RGBW Zoom User Manual 19
Effects
See ‘DMX protocol’ on page 24 for a full list of the DMX channels and values required to control the different effects.
Color control
All DMX modes offer full RGBW color mixing.
Besides color mixing, the following 32 color presets can be selected directly in
9-channel mode:
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Color 9
Color 10
Color 11
Color 12
Color 13
Color 14
Color 15
Color 16
Color 17
Color 18
Color 19
Color 20
Color 21
Color 22
Color 23
Color 24
Color 25
Red Green Blue White
255 0 0 0
255 50 0 30
255 100 0 0
255 150 0 0
255 200 0 50
255 255 0 0
200 255 0 0
150 255 0 10
100 255 0 0
50 255 0 50
0 255 0 0
0 255 50 10
0 255 100 0
0 255 150 0
0 255 200 10
0 255 255 0
0 200 255 0
0 150 255 10
0 100 255 0
50 0 255 0
100 2 255 0
150 0 255 50
200 0 255 0
20 RUSH PAR 2 RGBW Zoom User Manual
Color 26
Color 27
Color 28
Color 29
Color 30
Color 31
Color 32
Red Green Blue White
255 0 255 0
255 0 200 0
255 0 150 0
255 0 100 0
255 0 50 50
255 255 255 255
Zoom
Zoom can be controlled via DMX in 9-channel mode, allowing the beam angle to be varied from 10° to 60°.
Shutter effect
The electronic ‘shutter’ effect is available in 9-channel mode. It provides instant open and blackout, variable speed regular and random strobe.
Electronic dimming
Overall intensity can be adjusted 0-100% using electronic dimming in 9channel mode. Two channels can be used to control intensity: the first gives coarse 0-100% control, the second gives 16-bit fine adjustment.
RUSH PAR 2 RGBW Zoom User Manual 21
Maintenance
Read ‘Safety information’ on page 4 before servicing the fixture.
Refer any service operation not described in this user manual to a qualified service technician.
Disconnect mains power before cleaning or servicing the fixture.
Service the fixtures in an area where there is no risk of injury from falling parts, tools or other materials.
Cleaning
Excessive dust, smoke fluid, and particle buildup degrades performance, causes overheating and will damage the fixture. Damage caused by inadequate cleaning or maintenance is not covered by the product warranty.
The cleaning of external optical lenses must be carried out periodically to optimize light output. Cleaning schedules for lighting fixtures vary greatly depending on the operating environment. It is therefore impossible to specify precise cleaning intervals for the fixture. Environmental factors that may result in a need for frequent cleaning include:
• Use of smoke or fog machines.
• High airflow rates (near air conditioning vents, for example).
• Presence of cigarette smoke.
• Airborne dust (from stage effects, building structures and fittings or the natural environment at outdoor events, for example).
If one or more of these factors is present, inspect fixtures within their first 100 hours of operation to see whether cleaning is necessary. Check again at frequent intervals. This procedure will allow you to assess cleaning requirements in your particular situation. If in doubt, consult your RUSH by
Martin dealer about a suitable maintenance schedule.
Use gentle pressure only when cleaning, and work in a clean, well-lit area. Do not use any product that contains solvents or abrasives, as these can cause surface damage.
To clean the fixture:
1. Disconnect the fixture from power and allow it to cool for at least 15 minutes.
2. Vacuum or gently blow away dust and loose particles from the outside of the fixture and the air vents with low-pressure compressed air.
22 RUSH PAR 2 RGBW Zoom User Manual
3. Clean the LED lenses by wiping gently with a soft, clean lint-free cloth moistened with a weak detergent solution. Do not rub the surface hard: lift particles off with a soft repeated press. Dry with a soft, clean, lint-free cloth or low-pressure compressed air. Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water.
4. Check that the fixture is dry before reapplying power.
Fuse replacement
If the fixture is completely dead, the fixture’s primary fuse F1 may have blown and it may be necessary to install a new fuse. This fuse is located in a fuseholder next to the Mains OUT socket on the connections panel (see 5 in
‘Fixture overview’ on page 12).
To change the fuse:
1. Disconnect the fixture from power and allow it to cool for at least 15 minutes.
2. Use a large flat-bladed screwdriver to unscrew the cap of the fuseholder.
3. Replace the fuse with one of the same type and rating only.
4. Reinstall the fuseholder cap before reapplying power.
Service and repairs
There are no user serviceable parts inside the fixture. Do not open the housing.
Do not try to repair the fixture by yourself as this may result in damage, malfunction and it may potentially void your product warranty. The equipment must only be serviced or repaired by an authorized RUSH by Martin service technician.
Installation, on-site service and maintenance can be provided worldwide by the Martin Professional Global Service organization and its approved agents, giving owners access to Martin’s expertise and product knowledge in a partnership that will ensure the highest level of performance throughout the product’s lifetime. Please contact your RUSH by Martin supplier for details.
RUSH PAR 2 RGBW Zoom User Manual 23
DMX protocol
5-channel mode
Channel Value Function
1 0-255 Red 0 100%
2 0-255 Green 0 100%
3 0-255 Blue 0 100%
4 0-255 White 0 100%
5 0-255 Zoom wide narrow
9-channel mode
Channel Value Function
1 0-255 Dimming coarse 0100%
2 0-255 Dimming fine
0-7
8-15
16-131
132-167
168-203
204-239
240-247
248-255
Off
Open
Shutter strobe effect, slow fast
Fast close, slow open
Slow close, fast open
Pulse open and close
Shutter strobe effect, random strobe
Open
Fade type
Default
Fade 0
Fade 0
Fade 0
Fade 0
Fade 128
Fade type
Default
Fade 0
Fade 0
Snap 12
Fade 0
Fade 0
Fade 0
Fade 0
24
0-10
11-15
16-20
21-25
26-30
31-35
36-40
41-45
46-50
Open (white)
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
RUSH PAR 2 RGBW Zoom User Manual
Snap 0
Channel Value Function
131-135
136-140
141-145
146-150
151-155
156-160
161-165
166-170
171-175
176-180
181-185
186-190
191-192
193-214
215-221
222-243
244-247
248-251
252-255
51-55
56-60
61-65
66-70
71-75
76-80
81-85
86-90
91-95
96-100
101-105
106-110
111-115
116-120
121-125
126-130
Color 9
Color 10
Color 11
Color 12
Color 13
Color 14
Color 15
Color 16
Color 17
Color 18
Color 19
Color 20
Color 21
Color 22
Color 23
Color 24
Color 25
Color 26
Color 27
Color 28
Color 29
Color 30
Color 31
Color 32
Color 33
Color 34
Color 35
Color 36
Open (white)
Color wheel rotation effect
Clockwise rotation fast slow
Stop (wheel stops at current position)
CCW rotation slow fast
Random colors
Random color, fast
Random color, medium
Random color, slow
Zoom narrow
Fade type
Default
Fade 128
RUSH PAR 2 RGBW Zoom User Manual 25
Control menus
To access the control menus, press the MENU button. Use the UP and DOWN buttons to navigate the menus. Select any required menu option using the
ENTER button. For more information, see ‘Using the control menus’ on page
14.
Default fixture settings are shown in bold.
Menu Setting/value Explanation
DMX Address
Channel Mode
1–512
5 channel
9 channel
Set fixture’s DMX address
Select DMX mode
Dimmer Curve
Blackout
Backlight
White balance
Manual Test
Auto Test
Temp.
Fixture time
Firmware Version
Reset
4 S-curve
Yes
Hold
Set fixture behavior if DMX signal stops: blackout or hold current effect
On
Off
Automatically turn off display backlight when not in use
Red
Green
Blue
Red
Green
Blue
White
Zoom
Dimmer
Strobe
RGB fixture white balance adjustment
Manually test individual effects
Set stand-alone scene
Automatic test of all effects
Display fixture’s current temperature
Display total operation time
Display currently installed firmware version
Force a fixture reset
26 RUSH PAR 2 RGBW Zoom User Manual
Troubleshooting
This section describes a few common problems that may occur during operation and provides some suggestions for easy troubleshooting:
Symptom Potential cause Remedies
No light from fixture or fans not working.
One of the control channels is unresponsive or only responds intermittently.
Fixture does not respond to DMX control.
Power supply issue, such as blown fuse, faulty connector or damaged cable.
DMX setup or DMX link fault.
Damaged step motor or cable connection.
Incorrect DMX addressing.
Fault on DMX link due to damaged connector or cable, or potential interference from proximity to a highvoltage installation.
Check whether fixture’s power indicator LED is lit.
Check all power connections and cables.
Replace fixture’s primary fuse.
See next section.
Contact your RUSH by
Martin™ authorized distributor or service center for assistance.
Ensure that fixture’s DMX address matches address set on DMX control device.
Check that fixture DMX LED is on, and if not, check all
DMX cables and connections.
Ensure that DMX link is terminated.
Check that all components on DMX link use standard
DMX polarity.
Attempt to control the fixture with another DMX control device.
Move or shield link if it is close to an unshielded highvoltage installation.
RUSH PAR 2 RGBW Zoom User Manual 27
Specifications
Physical
Dimensions (LxWxH) .......................... 266x287x329 mm (10.5x11.3x13.0 in.)
Weight .................................................................................... 5.5 kg (12.1 lbs.)
Dynamic Effects
Color mixing ........................................................................................... RGBW
Color presets ................... 36 color presets plus full white, ‘color wheel’ effects
Electronic dimming ................................ 0 - 100%, four dimming curve options
Strobe and pulse effects ................ Variable speed and action, random strobe
Electronic 'shutter' effect .......................................... Instant open and blackout
Zoom ................................................................................................. Motorized
Control and Programming
Control options .......................................................... DMX, stand-alone scene
DMX channels .............................................................................................. 5/9
White balance control ............................................................ RGB adjustment
DMX address setting ........................................Control panel with LCD display
Stand-alone programming ...............................Control panel with LCD display
Protocol .......................................................................... USITT DMX512/1990
Optics
Light source .......................................... 12 x 10 W RGBW Osram Ostar LEDs
Minimum LED lifetime ..................... 50 000 hours (to >70% luminous output)*
Beam angle ......................................................................................... 10° - 60°
*Figure obtained under manufacturer´s test conditions
28 RUSH PAR 2 RGBW Zoom User Manual
Construction
Color ........................................................................................................ Black
Housing ............................................................................................. Aluminum
Protection rating ........................................................................................ IP 20
Installation
Mounting points ............................. Adjustable bracket, surface or truss mount
Location ................................................................................... Indoor use only
Orientation .................................................................................................. Any
Minimum distance to illuminated surfaces ...................................... 2 m (6.4 ft.)
Minimum distance to combustible material .................................... 0.2 m (8 in.)
Connections
AC power input .................................................................... Neutrik PowerCon
AC power throughput ........................................................... Neutrik PowerCon
DMX data in/out .................................................................... 5-pin locking XLR
Electrical
AC power ........................................................... 100-240 V nominal, 50/60 Hz
Typical power consumption .................................................................... 151 W
Fuse .......................................................................................................T 6.3 A
Power supply unit.................................... Auto-ranging electronic switch mode
Maximum power and current
120 V, 60 Hz ................................................................1.3 A, 151 W, PF 0.993
230 V, 50 Hz ................................................................0.7 A, 148 W, PF 0.961
Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.
Thermal
Cooling ...................................... Forced air (temperature regulated, low noise)
Maximum ambient temperature (T
Minimum ambient temperature (T a a
max.) ................................. 40° C (104° F)
min) ......................................... 0°C (32° F)
Included Items
Mounting bracket
Power cable, 6 A, 18 AWG, 0.75 mm
2 mains plug
, UL- listed, H05VV-F, 1.5 m, without
Accessories
Cables for connection to power in chains, 16 A, US/Canada
Power input cable, 12 AWG, SJT, with PowerCon input connector, 3 m (9.8 ft.) ............................ P/N 11541503
Power relay cable, 12 AWG, SJT, with PowerCon connectors, 1.4 m (4.6 ft.) ................................ P/N 11850099
Power relay cable, 12 AWG, SJT, with PowerCon connectors, 2.25 m (7.4 ft.) .............................. P/N 11850100
RUSH PAR 2 RGBW Zoom User Manual 29
Power relay cable, 12 AWG, SJT, with PowerCon connectors, 3.25 m (10.7 ft.) ............................. P/N 11850101
Cables for connection to power in chains, 16 A, EU
Power input cable, 2.5 mm
2
, H05VV-F, with PowerCon input connector, 3 m (9.8 ft.) ............................. P/N 11541007
Power relay cable, 2.5 mm
2
, H05VV-F, with PowerCon connectors, 1.4 m (4.6 ft.) ................................. P/N 11541008
Power relay cable, 2.5 mm
2
, H05VV-F, with PowerCon connectors, 2.25 m (7.4 ft.) ............................... P/N 11541009
Power relay cable, 2.5 mm
2
, H05VV-F, with PowerCon connectors, 3.25 m (10.7 ft.) ............................. P/N 11541010
Power connectors
Neutrik PowerCon NAC3FCA power input connector, cable mount, blue ................................. P/N 05342804
Neutrik PowerCon NAC3FCB power output connector, cable mount, light grey ....................... P/N 05342805
Installation hardware
Half-coupler clamp ..................................................................... P/N 91602005
G-clamp (suspension vertically downwards only) ...................... P/N 91602003
Quick-trigger clamp (suspension vertically downwards only) .... P/N 91602007
Safety wire, safe working load 50 kg ......................................... P/N 91604003
Related Items
RUSH Software Uploader 1™ ................................................... P/N 91611399
Ordering Information
RUSH PAR 2 RGBW Zoom™ in cardboard box ....................... P/N 90480040
Specifications are subject to change without notice. For the latest product
specifications, see www.martin.com
Disposing of this product
RUSH by Martin™ products are supplied in compliance with Directive 2012/19/EC of the European Parliament and of the Council of the European Union on WEEE
(Waste Electrical and Electronic Equipment), where applicable. Help preserve the environment! Ensure that this product is recycled at the end of its life. Your supplier can give details of local arrangements for the disposal of RUSH by Martin products
30 RUSH PAR 2 RGBW Zoom User Manual
Innovation Quality Performance
advertisement