Arctic Spas® Quick Reference Card
The Quick Reference Card provides a quick overview of your spa’s main functions and
the operations accessible with your digital control pad.
Starting Pump 1:
Press Pump 1 button to turn Pump 1 on at low
speed. Press a second time to turn Pump 1 to high
speed. A third time turns Pump 1 off. A built-in timer
automatically turns Pump 1 off after 20 minutes,
unless it has been manually deactivated.
The Pump 1 indicator lights up when Pump 1 is on
at high speed. It flashes when Pump 1 is on at low
speed.
Starting Pump 2:
Press Pump 2 button to turn pump 2 on. A second
time turns Pump 2 off. A built-in timer automatically
turns Pump 2 off after 20 minutes, unless it has been
manually deactivated.
The Pump 2 indicator lights up when Pump 2 is on
at high speed.
3
4
5
Starting Pump 3:
Press Pump 3 button to turn Pump 3 on. Press a
second time to turn Pump 3 off. A built-in timer
automatically turns Pump 3 off after 20 minutes,
unless it has been manually deactivated.
Starting Pump 4 (Epic series only):
Press Pump 4 button to turn Pump 4 on. Press a
second time to turn Pump 4 off. A built-in timer
automatically turns Pump 4 off after 20 minutes,
unless it has been manually deactivated.
Starting Pump 5 (Epic series only):
Press Pump 5 button to turn Pump 5 on. Press a
second time to turn Pump 5 off. A built-in timer
automatically turns Pump 5 off after 20 minutes,
unless it has been manually deactivated.
Starting the blower:
Press the Blower button once to turn on the Therapy
Air (TA) blower. Press a second time to turn on the
SuperJet* (SJ) blower on. A third time turns the TA
blower off. A fourth time turns the SJ blower off.
*On Super Jet equipped single pump spas only
Setting water temperature:
Use Up or Down arrow button to regulate water
temperature. The temperature setting will be
displayed for 5 seconds to confirm your new selection. Water temperature can be adjusted by 1º
increments from 59 to 104ºF (15 to 40ºC).
The temperature symbol indicates the desired temperature, NOT the current water temperature.
Automatic water heater start:
When water temperature is 1ºF (0.5ºC) lower than
the Set Point, the heater will automatically turn on &
heat until the water temperature reaches 1ºF (0.5ºC)
above the set point.
The Heater indicator lights up when the heater is on.
Temperature unit:
Press and hold the light button for 5 seconds to toggle
between ºF and ºC.
Turning the light on:
Press Light button to turn light on. Press a second
time to turn light off. A built-in timer automatically
turns it off after 2 hours, unless it has been manually
deactivated.
The Light indicator is displayed when the light is on.
Stereo (on stereo-equipped spas):
Any user function will turn the stereo on for 2 hours.
Waterfall
The waterfall will be operated by the pump nearest
to it and will vary by spa model & series. If Peak 2 is
installed, the waterfall can be turned on by holding the
blower button (pump 3 on Epic series) for 3 seconds.
Hold for 3 seconds again to turn it off.
Standby mode:
Press and hold Pump 3 button for 5 seconds to enter
standby mode. The “stby” message is displayed and
heating & filtering will be disabled for 30 minutes.
Pressing any button will exit standby.
Note: If the system is turned down while the heater is
on, Pump 1 will run for an additional 3 minutes.
Pad Lockout:
There are two modes you can choose from: Full or partial lock. Full lock means that all keypad functions are
locked. Partial lock means that only the basic functions
will remain accessible (pumps, blower, light).
Locking your digital control pad:
Press and hold Pump 1 for 5 seconds. The display will
show “LocP”, with “P” representing partial lock. Release
the button and the keypad will be in Partial lock mode.
Keep button pressed down for 5 more seconds if you
want to be in Full lock mode. The “LocF” message will
then be displayed.
When control pad is locked, all automatic functions will
run as usual. If a button is pressed down, a “LocP” or
“LocF” message will be displayed for 1 second. To unlock
the keypad, simply press and hold Pump 1 button again
for 5 seconds.
Boost Mode:
Press and hold Pump 2 button for 5 seconds to enable
Boost mode. In this mode, Pump 1 high speed and the
ozonator will run for 45 minutes. When enabled, “boo”
message is displayed. This mode is used to speed up
filtration after intensive use of the spa or to help mix
chemicals just added to the spa. Pressing any button
will exit boost mode.
PROGRAMMING THE SETTINGS
During a filter cycle:
- Pump 2, Pump 3 (Pump 4 & Pump 5 on an epic series spa) and the blower run for 20 seconds, then
- Pump 1 runs at low speed for the programmed number of hours (see below), and
- The ozonator is turned on.
3
Sett
3
O 03
O 03
5
5
Press the Filter button (pump 5 on
epics) to enter into your filtration
options. Your display will show
“Sett” and from here you will be
able to choose your settings.
Press your Filter/Pump 5 button again to display your first
option. This is your Ozone
Cycle Duration (if equipped).
On 02
F 06
5
Use your arrow keys to select
your Ozone Cycle Duration.
You can select from 1 to 24
hours per day.
F 06
p
p
5
Use your arrow keys to select
your Onzen Cycle Duration.
You can select from 1 to 24
hours per day.
FF 02
Use your arrow keys to select
your Filter Cycle Frequency
from 1 to 4 times per day.
On 02
Press your Filter/Pump 5
button again. Your display
will now show the settings
for your Filter Duration.
Press your Filter/Pump 5
button again. Your display
will now show the settings
for your Onzen system (if
equipped).
FF 02
5
Use your arrow keys to select
your Filter Duration in hours.
You can select from 0 to 6
hours.
Press your Filter/Pump 5 button again. Your display will
now show the settings for
your Filter Cycle Frequency.
Please note:
You will see the options that are applicable to your spa. If you have neither ozone nor onzen,
you will proceed directly into setting your Filter Duration. Also, though an Epic topside is of a
different design, the steps are as shown.
You can move backwards through the settings by pressing the Pump 3 button (Pump 4 on Epic
series spas). The Pump 1 button will allow you to exit without saving any changes. When you
get to the end of the options, press the filter key one last time to save changes and begin a filter
cycle immediately. If you do not press the filter key again your changes will be saved and the
filter cycle will begin when you have programmed it to do so.
45 Minute filter cycle time-out:
If you turn a pump, blower or light on during a filter cycle, the cycle will be interrupted and will only resume 45 minutes after you
(or the system) have turned the last active output off.
or replace
-
4 dashes are displayed
The Processor has been damaged.... Do Not Enter the
Water... this is usually caused by abnormal power
fluctuations, call your dealer or service supplier.
*If activated in Low-level programming the lights will flash when there is an error
code present
">
