BOXLIGHT Projector Installation guide

NE 151 Highway 300, Suite A
PO Box 2609
Belfair, WA 98528
360.464.2119
www.boxlight.com
MP65e
Downloaded From projector-manual.com Boxlight Manuals
Contents
About this manual .....................1
Contents........................................2
Projector features.......................3
Preparations.................................3
Contents of package.........................3
Part names....................................4
Projector............................................4
Control panel ....................................5
Remote control .................................5
Setting up......................................6
Arrangement.....................................6
Connecting your devices..................8
Connecting power supply................10
Using the security anchor................10
Using the hiding-style Handle..........11
Remote control..........................12
Putting batteries..............................12
About the remote control signal......13
Using as a simple PC mouse &
keyboard.........................................13
Power on/off...............................14
Turning on the power......................14
Turning off the power......................14
Operating....................................15
Adjusting the volume......................15
Adjusting the mute..........................15
Selecting an input signal.................15
Searching an input signal...............16
Selecting an aspect ratio................16
Adjusting the image position..........17
Adjusting the zoom and focus........17
Correcting the keystone
distortions........................................18
Stilling the Screen...........................19
Temporarily blanking the screen.....19
Using the menu function.................20
MENU
Picture menu(PC mode)......................21
Picture menu(Video mode).................22
Audio menu.........................................23
Setting menu(PC mode).....................24
Setting menu(Video mode).................25
Advanced menu..................................26
Logo Setting.................................26-A
Logo Capture................................26-B
Presentation menu..............................27
Security menu......................................28
Auto filter alert..................................30
PIN Key in operation...........................31
Maintenance...................................32
Lamp....................................................32
Lamp Warning...................................33
Air filter................................................34
Other care...........................................35
Troubleshooting............................36
Regarding the indicator lamps............36
Mistaken for machine defects.............37
List of supported Monitor Display.......39
Appendix
Ceiling Mounted Installation Guide.....40
PIN code number memo.....................41
2
Downloaded From projector-manual.com Boxlight Manuals
Projector features
1. Design with 3LCD optical system, provide you：Bright image, natural color,
smooth video playback and gentle for your eyes.
2. Design with high efficiency dust air filter and Auto Filter Alert. (See P30)
3. Easy to maintenance design function.(See P32~35)
4. Security PIN Lock function. (See P29)
5. Progressive scans accommodating for High-definition 1080i form.
6. Auto V keystone function, +/- 30 degrees.
7. Auto brightness control.
8. Auto ceiling function.
9. Support DVI ,YPbPr ,Composite Video and S-Video signal. (See P8)
10. Hiding-Style Handle to carry the projector easily. (See P11)
Preparations
Contents of package( Before Use )
Your projector should come with the items shown there. Contact immediately
your dealer if anything is missing.
(3)Battery
(1)Projector and Lens Cap
(5)Quick Start Guide
(2)Remote control
(6)Power Cable
(for Remote Control use)
(4)User’s Manual (CD)
(7)VGA Cable
(7)USB Cable
NOTE ► Keep the original packing materials, for future reshipment.
Be sure to use the original packing materials when moving the projector.
3
Downloaded From projector-manual.com Boxlight Manuals
Part names
Projector
(1)
. Lamp Cover
(3) (2)
(4)
The lamp is inside.
(2) Focus ring( SEE P17)
(1)
HOT!
(3) Zoom ring( SEE P17)
(4) Control panel( SEE P5)
(5) Speaker
(6) Adjustable knobs (x 2)
(7) Adjustable feet (x 2)
(8) Lens Cap
(9) Lens cover
(10) Intake vents
(13)
(11) Filter cover
The air filter is inside.
(10)
(12) Front IR receiver
(6)
(13) Security anchor( SEE P10)
(7)
(9)
(14) AC inlet( SEE P10)
(8) (12)
(15) S-VIDEO port( SEE P16)
(16) AUDIO L/R port( SEE P8)
(17) VIDEO port( SEE P8)
(18) COMPUTER IN1 port( SEE P8)
(24) (23)
(15) (17) (16)
(19) COMPUTER IN2 / DVI port( SEE P8)
(20) USB port( SEE P13)
(21) AUDIO 1 IN port( SEE P8)
(22) AUDIO 2 IN port( SEE P8)
(23) AUDIO OUT port ( SEE P8)
(24) MONITOR OUT port
(25) YPbPr port ( SEE P16)
&(26) L-AUDIO IN-R port( SEE P8)
(28) RS-232C port( SEE P8)
(11)
(29) LAN port (Optional)( SEE P8)
(14)
(19)
(5)
(22) (18)
(21) (25)&(26) (28)
(20)
(29)
WARNING
HOT! :
Do not touch the lamp cover and the outlet vents during use or just after use,
since it is too hot.
Do not look into the lens or vents while the lamp is on, since the strong light
is not good for your eyes.
CAUTION
Maintain normal ventilation to prevent the projector from heating up. Do not cover,
block or plug up the vents. Do not place anything that can stick or be sucked to the
vents, around the intake vents. Change the air filter periodically.
Do not use the security anchor to prevent the projector from falling down, since it
is not designed for it.
4
Downloaded From projector-manual.com Boxlight Manuals
Part names
Control panel
(1) ON/STANDBY button(SEE P14)
(2) AUTO button(SEE P15)
(3) INPUT button(SEE P15)
(4) BLANK button
(5) KEYSTONE button
(6) MENU button(SEE P16)
(7) MENU-Left/Right
MENU-Up/Down
(8) POWER indicator(SEE P10,P14)
(9) LAMP indicator (SEE P14)
(1)
(8)
(9)
(7)
MENU
(2)
(6)
(5)
(3)
(4)
Remote control
(1) Power button.(SEE P14)
(2) Point button.
(3) Mouse Left button.
(4) Menu-up button / Menu-down button.
(5) Menu button.
(6) Keystone up /down button.
(7) PC button.(SEE P15)
(8) Video button.(SEE P16)
(9) Auto button.(SEE P15)
(10) Blank button.
(11) Still button.
(12) Zoom in / Zoom out button.(SEE P17)
(13) Mute button.(SEE P15)
(14) Volume up / down button.(SEE P15)
(15) Menu-left button / Menu-right button.
Menu-up button / Menu-down button.
(SEE P16)
(16) Mouse Right button.
(17) Laser pointer button.
(1)
(17)
(2)
(16)
(3)
(4)
(15)
(5)
(14)
(6)
(13)
(7)
PC
(8)
(12)
Video
(9)
(10)
(11)
5
Downloaded From projector-manual.com Boxlight Manuals
Setting up
Install the projector according to the environment and manner the projector will
be used in.
Arrangement
The distance between the projector and screen determines the actual image size.Refer to
this table, in case of 4:3 aspect ratios. The values M shown in the table are calculated for
a full size screen.
Screen
Lens center
Side view
M
On a horizontal surface
M
D Screen size (diagonal)
M Projection distance
Suspended from the ceiling
D
H
H
H Screen height
M
Screen size
(inch)
M
Distance (m)
M
Distance (feet)
40
60
70
80
100
Tele
1.50
2.23
2.60
2.97
3.70
Wide
1.24
1.85
2.15
2.45
3.06
Tele
4.91
7.32
8.52
9.73
12.14
Wide
4.06
6.06
7.05
8.05
10.04
200
300
7.37
11.04
6.10
9.14
24.18
36.22
20.01
29.97
NOTE
► Allowing the proper amount of space on the top, sides, and rear of the
projector cabinet is critical for proper air circulation and cooling of the unit. When in
against at wall, leave about 20cm (7.9in.) between the projector and the wall.
6
Downloaded From projector-manual.com Boxlight Manuals
Setting up
WARNING
• Place the projector in a stable horizontal position.
If the projector falls or is knocked over it could cause injury and/or damage
to the projector. Using a damaged projector could then result in fire and/or
electric shock.
(1) Do not place the projector on an unstable, slanted or vibrational surface
such as a wobbly or inclined stand.
(2) Do not place the projector on its side, front or rear position.
(3) Consult with your dealer before a special installation such as suspending
from a ceiling.
• Place the projector in a cool place, and ensure that there is sufficient
ventilation. The high temperature of the projector could cause fire, burns and
/or malfunction of the projector.
(1) Do not stop-up, block or otherwise cover the projector's vents.Keep a
space of 20 cm or more between the sides of the projector and other
objects such as walls.
(2) Do not place the projector on metallic thing or anything weak in heat.
(3) Do not place the projector on carpet, cushions or bedding.
(4) Do not place the projector in direct sunlight or near hot objects such as
heaters.
(5) Do not place anything near the projector lens or vents, or on top of the
projector.
(6) Do not place anything that may be sucked into or stick to the vents on
the left of the projector. This projector has some intake vents also on the
left.
• Avoid placing the projector in smoky, humid or dusty place.
• Do not place the projector anyplace where it may get wet. Getting the
projector wet or inserting liquid into the projector could cause fire, electric
shock and/or malfunction of the projector.
(1) Do not place the projector in a bathroom or the outdoors.
(2) Do not place anything containing liquid near the projector.
CAUTION
Placing the projector in such places could cause fire, electric shock and/or
malfunction of the projector.
(1) Do not place the projector near humidifiers, smoking spaces or a kitchen.
(2) Position the projector to prevent light from directly hitting the projector's
remote sensor.
7
Downloaded From projector-manual.com Boxlight Manuals
Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations
to connect them.
PC
VGA out DVI out
Audio out Monitor in
Speaker
RS-232C
USB
LANS
(Optional Function)
Audio out
VGA out
Monitor in
VCD/DVD Player
Audio out
S-video out Video out Audio out (L)&(R)
Y Pb/Cb Pr/Cr Audio out (L)&(R)
8
Downloaded From projector-manual.com Boxlight Manuals
Setting up
Connecting your devices(Continue)
NOTE ►Be sure to read the manuals for devices before connecting them to the
projector, and make sure that all the devices are suitable to be connected with this
product. Before connecting to a PC, check the signal level, the signal timing, and the
resolution.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals which
are not supported by this projector.
-The best display performance will be achieved if the resolutions of the input signal
and the projector panel are identical.
►While connecting, make sure that the shape of the cable's connector fits the port to
connect with. And be sure to tighten the screws on connectors with screws.
►When connecting a laptop PC to the projector, be sure to activate the PC’s external
monitor(RGB) output. (Set the laptop PC to CRT display or to simultaneous LCD and
CRT display.) For details on how this is done, please refer to the instruction manual of
the corresponding laptop PC.
►In some cases, this projector may not display a proper picture or display any picture
on screen. For example, automatic adjustment may not function correctly with some
input signals. An input signal of composite sync may confuse this projector, so the
projector may not display a proper picture.
WARNING ►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION ►Turn off all devices and unplug their power cords prior to
connecting them to projector. Connecting a live device to the projector may
generate extremely loud noises or other abnormalities that may result in
malfunction or damage to the device and the projector.
►Use appropriate accessory or otherwise designed cables. Ask your dealer
about non-accessory cables which may have other length or equipped with
a core. For cables with a core only at one end, connect the end with the core
to the projector.
►Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the
projector.
9
Downloaded From projector-manual.com Boxlight Manuals
Setting up
Connecting power supply
1.Connect the connector of the power cord
POWER indicator
to the AC inlet of the projector.
2.Firmly plug the power cable’s plug into
the outlet.The POWER indicator will
begin blinking in green.The projector
work on stand by mode.
AC inlet
Outlet
WARNING
►Please use extra caution when connecting the power cord, as incorrect or
faulty connections may result in fire and/or electrical shock.
►Only use the power cord that came with the projector. If it is damaged,
contact your dealer soon.
►Only plug the power cord into an outlet rated for use with the power cord's
specified voltage range. The power outlet should be close to the projector
and easily accessible. Remove the power cord for complete separation.
►Never modify the power cord.
Using the Security Anchor
The product has design security
anchor and PIN LOCK functions
(SEE P31)to help prevent
unauthorized removal projector.
Security Anchor
WARNING
►Do not use the security anchor to prevent the projector from falling down or
held, since it is not designed for it.
NOTE ►The security anchor is not comprehensive theft prevention measures.
It is intended to be used as supplemental theft prevention measure.
10
Downloaded From projector-manual.com Boxlight Manuals
Setting up
Using the Hiding-Styled Handle
Refer to the picture operation direction to
pull the handle.
Hiding-Styled Handle
NOTE ►This handle is designed to carry the projector for short distance only.
►Please do not have added on other goods to use together, it can damage
the projector.
11
Downloaded From projector-manual.com Boxlight Manuals
Remote control
Putting batteries
Please set the batteries to the remote control before using it. If the remote control starts
to malfunction, try to replace the batteries. If you will not use the remote control for long
period, remove the batteries from the remote control and store them in a safe place.
1.Remove the battery cover.
Slide back and remove the battery cover in the
direction of the arrow.
2.Insert the batteries.
Align and insert the two AAA batteries according
to their plusminus terminals
3.Close the battery cover.
Replace the battery cover in the direction of the
arrow and snap it back into place.
WARNING About the Battery
►Always handle the batteries with care and use them only as directed.
Improper use may result in battery explosion, cracking or leakage, which could
result in fire, injury and/or pollution of the surrounding environment.
►Be sure to use only the batteries with the mentioned specification.
►Do not use batteries of different types at the same time.
►Do not mix a new battery with used one. Make sure the plus and minus
terminals are correctly aligned when loading a battery.
►Keep a battery away from children and pets.
►Do not recharge, short circuit, solder or disassemble a battery.
►Do not allow a battery in a fire or water.
►Keep batteries in a dark, cool and dry place. If you observe a leakage of a
battery, wipe out and then replace a battery. If it adhere your body or clothes,
rinse well with water immediately.
►Dispose of batteries in accord with environmental laws.
12
Downloaded From projector-manual.com Boxlight Manuals
Remote control
About the remote control signal
1.The remote control works with the
remote sensor
projector’s remote sensor. This
projector have 2 remote sensors
on the front and back.
2.The sensor senses the signal within
the following range when the sensor
is active:30 degrees (15 degrees to
the left and right of the sensor) within
7 meters about.
150
150
NOTE ► Laser pointer of the remote control is used in place of a finger or rod.
Never look directly into the laser beam outlet or point the laser beam at other people.
Using as a simple PC mouse & keyboard
The enclosed remote control works as a
simple mouse and keyboard of the PC,
when the projector's USB port connects
with the PC's mouse port via a mouse
cable.(SEE P4)
CAUTION ►Improper use of the simple mouse & keyboard function could
damage your equipment. While using this function, please connect this
product only to a PC.
13
Downloaded From projector-manual.com Boxlight Manuals
Power on/off
Turning on the power
1.Make sure that the POWER indicator
ON/STANDY BY BUTTON
POWER INDICATOR
turns in steady green and the lens
cover is removed.
2.Press the STANDBY/ON button on
MENU
the projector or the remote control.
3.The projection lamp will light up,
the LAMP indicator will not light in
red and the POWER indicator will
begin light in green.
To display the picture, select an input
signal according to the section
“Selecting an input signal” (SEE 15).
PC
Video
Lens cover
Turning off the power
1.Press the ON/STAND BY button on the projector or
the remote control. The message [ Power off. Please
press key again to power off. ] will appear on the
screen for about 5 seconds.Press again and the
projector lamp will go off, the POWER indicator will
begin light in green and the LAMP indicator will begin
blinking in red.
2.The LAMP indicator will stop blinking and light in
red. And then the POWER indicator begin blinking
in green when the lamp cooling is complete. Unplug
the power cable.
Attach the lens cap.Do not turn the projector on
immediately after turning off.Turning projector on
again too soon could shorten the lifetime of some
consumable parts of the projector.
LAMP INDICATOR
MENU
WARNING►A strong light is emitted when the projector’s power is on.
Do not look into the lens of the projector or look inside of the projector through
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or
just after use, since it is too hot.
►Remove the power cord for complete separation.
14
Downloaded From projector-manual.com Boxlight Manuals
Operating
Adjusting the volume
1.Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in
adjusting the volume.
2.Use the +/- cursor buttons to adjust the volume.
To close the dialog and complete the operation,
press the MENU button and the menu will
disappear after a few seconds.
Adjusting the mute
Volume
1.Press the MUTE button on the remote control.
A dialog will appear on the screen indicating
that you have muted the sound.
2.If you do not do anything, the dialog will
Mute
PC
Video
automatically disappear after a few seconds.
3.Press the MUTE button will bring the sound
back to the level before muting.
Selecting an input signal
1.To select a new input,press the PC button
on the projector or remote control. Each time
you press the button, the projector switches
its input port as below.
COMPUTER IN1  COMPUTER IN2
DVI
PC BUTTON
Video BUTTON
MENU
PC
Video
2.If press the Video button on the remote
control.Each time you press the button,
the projector switches its input port as
below.
YPbPr  COMPOSITE VIDEO
 S-VIDEO
PC
Video
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
15
Operating
Selecting an input signal (continued)
3.If press AUTO button on the projector.
Each time you press the button, the
projector’s image is in Blank mode.
Automatically adjusts the setting to
match the current input.
MENU BUTTON
MENU
PC
Searching an input signal
Video
1.Please Press the MENU button on the
projector or remote control.
AUTO BUTTON
▲
2.After you can use the
cursor button
to chiose [ ON ] in the AUTO SEARCH
item of the SETTING menu.
The projector will start to check its input
ports in order to find any input signals.
When an input is found, the projector
will stop searching and display the
image. If no signal is found, the projector will
return to the source before searching and the
projector switches its input port as below.
PC
Video
COMPUTER IN1  COMPUTER IN2  DVI  YPbPr
S-VIDEO
COMPOSITE VIDEO

Selecting an aspect ratio
▲
▲
1.Press the MENU button on the projector or remote control.
2.After you can select the RESIZE item of the ADVANCED menu. And use the
/
cursor buttons to adjust the aspect ratio.
For a PC signal
4:3  16:9
For a video signal ( s-video signal or component video signal)
4:3  16:9
For no signal
4:3 (fixed)
The RESIZE item does not work when no proper signal is inputted.
The NORMAL mode keeps the original aspect ratio setting.
Performing the automatic adjustment initializes the aspect ratio setting.
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
16
Operating
Adjusting the image position
When the place to put the projector is slightly uneven to the left or right, use the
feet to place the projector horizontally. Using the feet can also tilt the projector in
order to project at a suitable angle to the screen.
This projector has 2 feet and 2 knobs.
A foot is adjustable while pulling up the knob on the same side as it.
1.Holding the projector, pull the knobs up to loose the feet.
2.Position the front side of the projector to the desired height.
3.Release the knobs in order to lock the feet.
4.After making sure that the feet are locked, put the projector gently.
Holding the projector,press the adjustable knobs to extend the both feet.
CAUTION ►Do not handle the knobs without holding the projector,since the
projector may drop down.
Adjusting the zoom and focus
1.Use the focus ring to focus the picture.
2.Use the zoom ring to adjust the screen size.
RING DOOR
ZOOM RING
FOCUS RING
17
Downloaded From projector-manual.com Boxlight Manuals
Operating
Correcting the keystone distortions
1.Please Press the MENU button on the projector or remote control.
2.After you can use the► /► cursor button to select the KEYSTONE V item of
the SETTING menu and press the► /► button for keystone adjustment.
(1)The KEYSTONE V item will displays a dialog for keystone correction.
(2)To close the dialog and complete this operation, press the MENU button again.
The dialog will automatically disappear after a few seconds if you do not do
anything.
(3) The adjustable range of this correction will vary among inputs. For some input,
this function may not work well.
(4) When the zoom adjustment is set to the TELE (telephoto focus), the automatic
keystone distortion correction may be excessive. This function should be used
when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever
possible.
SCREEN
SCREEN
KEYSTONE BUTTON
MENU
Press [ Left ] and [ Right ] buttons to correct
keystone distortion.
PC
Video
18
Downloaded From projector-manual.com Boxlight Manuals
Operating
Stilling the screen
1.Press the Still button on the remote control.
The [ Still ] indication will appear on the screen and the
projector will go into the Still mode.
To exit the still mode and restore the screen to normal, press
the still button again.
If the projector continues projecting a still image for a long time,
the LCD panel might possibly be burned in. Do not leave the
projector in the Still mode for too long.
Still
PC
Video
Temporarily blanking the screen
1.Press the Blank button on the projector or remote control.
The [ Blank ] indication will appear on the
screen and the projector will go into the
Blank mode.
To exit from the blank screen and return to
the input signal screen, press the BLANK
button again.
If the projector is left in Blank mode for more
than 15 minutes, the projector will
automatically shut off the lamp and begin
to cool-down mode.
BLANK BUTTON
PC
MENU
Video
BLANK
PC
Video
NOTE ►The sound is not connected with the blank screen function. If
necessary, set the volume or mute first.
19
Downloaded From projector-manual.com Boxlight Manuals
Operating
Using the menu function
This projector has the following categories:
ADVANCED, AUDIO, INPUT, PICTURE, PRESENTATION,SETTING and
SECURITY. ADVANCED MENU consists of functions often used, and the
other menus are classified into each purpose. Each of these menus is operated
using the same methods. The basic operations of these menus are as follows.
1.Press the MENU button on the remote control
or the projector.The MENU button on the
projector works as the cursor buttons.
CURSOR BUTTON
MENU BUTTON
2.Use the ▲/▼ cursor buttons to select an
category to operate.
MENU
3.Use the ◄/► cursor buttons to operate the
category.Then press the ► cursor button,
or the ENTER button to select an item. The
lower layer menu of the selected item
will appear.
4.Some functions cannot be performed
when a certain input port is selected,
or when a certain input signal is
displayed.
PC
Video
5.Reset all
After you select [ Reset all ] on the menu, the following confirmation message
will appear on the screen. Press the MENU button or ignore the message to
exit the [ Reset All ] function without changing any settings.
Reset all?
Please, press reset key to return default setting.
reset all
Yes
No
If select to reset all, press [ Yes ].
20
Downloaded From projector-manual.com Boxlight Manuals
Picture menu(PC Mode)
In the PICTURE category, items
shown in the table below can be
performed.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
Description
Brightness
000/50
Adjusts the overall image brightness.
DarkLight
Contrast
000/50
Adjusts the difference between strong and weak areas
of the image.
WeakStrong
Sharpness
000/002
Adjusts the image sharpness
WeakStrong
There may be some noise and/or the screen may flicker
for a moment when an adjustment is made. This is not a
malfunction.
Select mode(► cursor button)
Display mode
Natural
Nature color(default)
Cinema
Enhance contrast mode for Cinema mode
User color
Adjustments of each RGB color
Green Board
Adjusts the color settings and makes the projected
image on a green board more visible.
Powerful
Enhance brightness
Video
Keep the soft tender color
Presentation
For computer presentation use
User color
Select (► cursor button)
User Red
User Green
User Blue
000/50
000/50
000/50
21
Downloaded From projector-manual.com Boxlight Manuals
Picture menu(Video Mode)
In the PICTURE category, items
shown in the table below can be
performed.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
Description
Brightness
000/50
Adjusts the overall image brightness.
DarkLight
Contrast
000/50
Adjusts the difference between strong and weak areas
of the image.
WeakStrong
Sharpness
000/002
Adjusts the image sharpness
WeakStrong
Color
000/50
Adjusts the strength of whole color.
WeakStrong
This item can be selected only for a video signal,s-video
signal or component video signal.
Tint
000/50
Adjusts the image tint.
ReddishGreenish
This item can be selected only for a video signal,s-video
signal or component video signal.
Select mode(► cursor button)
Display mode
Natural
Cinema
User color
Green Board
Powerful
Video
Presentation
User color
User Red
User Green
User Blue
Nature color(default)
Enhance contrast mode for Cinema mode
Adjustments of each RGB color
Adjusts the color settings and makes the projected
image on a green board more visible.
Enhance brightness
Keep the soft tender color
For computer presentation use
Select (► cursor button)
000/50
000/50
000/50
22
Downloaded From projector-manual.com Boxlight Manuals
AUDIO menu
In the AUDIO category, items shown
in the table below can be performed.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
Description
Volume
000/40
Adjusts the volume
LowHigh
Mute
off/on
Mutes the volume off/on
23
Downloaded From projector-manual.com Boxlight Manuals
SETTING menu(PC Mode)
In the SETTING category, items
shown in the table below can be
performed.
When the source is computer.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor button
or enter to execute the item. Then
perform it according to the following
table.
Item
H position
Description
000/50
Move the image position horizontally
RightLeft
This item can be selected only for a computer
signal.Pressing the RESET button when the
H POSITION is selected will reset the
H POSITION to the default setting.
Move the image position vertically
DownUp
This item can be selected only for a computer
signal.Pressing the RESET button when the
V POSITION is selected will reset the
V POSITION to the default setting.
V position
000/50
Phase
000/19
Set the synchronization polarity
Frequency
000/100
Set the horizontal scanning frequency
Auto keystone
execute
Automatically Corrects keystone distortion in
image.
Corrects vertical keystone distortion in image
manually.
Shrink the button of the image Shrink the top of the image
Keystone V
-80/+80
Auto sync
execute
Sets all of the above settings automatically.
It can not include both Auto Keystone and
Keystone V items to implement the function.
Auto search
off/on
Search signal source manually or automatically.
The adjust able range of this function will vary
with the type of input signal. For some input,
this function may not work well.
24
Downloaded From projector-manual.com Boxlight Manuals
SETTING menu(Video Mode)
In the SETTING category, items
shown in the table below can be
performed.
When the source is video.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
Auto keystone
Description
execute
Automatically Corrects keystone distortion in
image manually.
Corrects vertical keystone distortion in image
manually.
Keystone V
-80/+80
Auto search
off/on
Shrink the button of the imageShrink the top of the image
The adjustable range of this function will vary
with the type of input signal. For some input,
this function may not work well.
Search signal source manually or automatically.
25
Downloaded From projector-manual.com Boxlight Manuals
ADVACED menu
In the ADVANCED category, items shown in the table below can be performed.
Select an item using the ▲/▼ cursor buttons, and press the► cursor button or
ENTER button to execute the item. Then perform it according to the following table.
Item
Description
Zoom/pan
execute
Execute digital zoom and pan function
Still
on/off
Freezes the current image on the screen.
Blank
Hide the image, displays a blank, black screen.
Reset all
Resets all Menu function to their factory default
values.
Resize
4:3
Language
English
(default)
Select the language that the menu and on
screen massage are display in
ENGLISH簡體中文繁體中文DEUTSCH
FRANÇAISITALIANOESPAÑOL
POLSKI日本語
Select the input source from:
Select source
COMPUTER IN1  COMPUTER IN2  DVI
YPbPr
S-VIDEO
VIDEO


The search is started from the current port.
Then when an input is found, the projector will
stop searching and display the image.
Logo Setting
execute
This function allows you to customize the
start-up logo.
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
26
ADVACED menu
Logo Setting
This function allows you to
customize the start-up logo.
IMPORTANT:
To execute the logo function,
you must to enter the PIN code
first.
Item
Logo Mode
Description
Select Mode( ► cursor button)
User
The image you captured.
Default
The factory logo.
Off
The blank image you can select color with
background function.
Logo Capture
Execute
Start to capture the image.
Background
Black
Set background color
Blue
White
Logo Size
Original
Display the segment of the image in original
size at center of the screen.
Full
Expend the image to full screen.
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
26-A
ADVACED menu
Logo capture
How to use this function?
1.Select
2
Logo capture item in the logo
setting menu, and press ► cursor
button.
2.You can see the red frame that can
Dispaly image
select captured area.
3.Use 4 direction bottoms to adjust the
position of the frame.
4.Press “MENU” to start capturing and
display a dialog.
4
Logo Capture In Progress.
NOTE ► You can only capture an image from computer mode.
► The area that can be captured is 512 x 384 dots.
26-B
Downloaded From projector-manual.com Boxlight Manuals
PRESENTATION menu
In the PRESENTATION category,
items shown in the table below can
be performed.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
Description
Auto ceiling
off/on
Automatically inverts the image when the
projector is turned upside down i.e.
When the projector is mounted on the ceiling.
Front
execute
Normal projection mode.
Ceiling
execute
Mirrors the image vertically, used when the
projector is mounted upside down.
Rear
execute
Mirrors the image horizontally, used when
projecting onto a rear projection screen.
Ceiling and
Rear
execute
Mirrors the image horizontally and vertically,
used when the projector is mounted upside
down and projecting onto a rear projection
screen.
Auto Brightness
off/on
Lamp mode
normal
economic
Economic mode reduces the lamp brightness.
Show Lamp timer
Lamp
Reset lamp
timer (optional)
Auto detects brightness; it turns to economic
mode automatically when the ambient light is
low.When the lamp mode is in economic,auto
brightness will not work.
execute
After changing a new lamp,execute this
function for reset the Lamp timer.(see below)
27
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
PRESENTATION menu
The lamp time is the time counted after the last resetting. It is shown in the
PRESENTATION menu as the usage time of the lamp.Pressing the RESET
button or the ► button displays a dialog.To reset the lamp time, select the
RESET using the ► button.
Reset Lamp Timer?
Select “No” to exit.
Lamp Reset
Yes
No
Please reset the lamp time only when you have replaced the lamp, for a suitable
indication about the lamp. For the lamp replacement, see the selection "Lamp" .
(SEE P32)
NOTE ► The replacement warning message is set to appear after about
2000 hours of lamp use in order to maintain the initial brightness and quality
of the projected images. When the lamp replacement message appears,
replace the lamp with a new one as soon as possible, even if it is still working.
28
Downloaded From projector-manual.com Boxlight Manuals
SECURITY menu
In the SECURITY category, items
shown in the table below can be
performed.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
PIN LOCK
PROTECTION
Description
Off
On 1
On 2
Off ：Turn off PIN lock protection.
On 1：PIN code is needed only first time after AC
switched off.
On 2：PIN code is needed every time the projector
been turned on.
CAUTION :
►Once the PIN code had been set, the projector can’t be
used unless you entered the correct PIN code.
►To avoid unnecessary trouble, if you activate the [ PIN
Lock Protection ] , it is highly recommended that you write
down the PIN code and store it in a safe place.
1.Press the MENU button on the projector or
remote control.
2.Use the ► cursor button to select the
Modify PIN item of the SECURITY category.
3.Press
► cursor button to change PIN lock protection
mode.
4.Please Enter the original PIN code.
Modify PIN
execute
(1) If the PIN is correct, system will allow you to change
a new PIN code.
(2) If the PIN is incorrect, a “Code Error” message will
appear.
5.Please Enter a new PIN code. And then enter again to
confirm.
NOTES ► To change the PIN lock protection state,
you must enter the PIN code first.
► Please enter: 0000 for first-time use.(default)
►Write your selected password down here in this
manual so that it will help you avoid the trouble
of forgetting the password,see the selection
“Appendix”. (SEE P41)
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
29
SECURITY menu
In the SECURITY category, items
shown in the table below can be
performed.
Select an item using the ▲/▼ cursor
buttons, and press the► cursor
button or ENTER button to execute
the item. Then perform it according
to the following table.
Item
Description
Filter timer
Showing the usage of filter hour.
Reset filter timer
Reset the filter timer after cleaning or change filter
Filter counter
500 Hours
800 Hours
1000 Hours
Select from (500Hs/800Hs/1000 Hs) depending on
the use environment.(default : 500 Hours)
Please see as below.
Auto Filter Alert
The function is to remind user for filter cleaning or replacement.
It is in the SECURITY category as the usage time of the air filter.Pressing the ►
cursor button displays a dialog. And then select an appropriate filter counter time
according to the use environment.
When the operation time reached the timer set, a warning message will appears
on the screen to remind user that the filter cleaning is required.
Filter Replace...
Filter has been used more than 500 hours.
NOTE ► Select from (500H/800H/1000H) according to the use environment.
Filter counter can set to longer in a clean environment.
► Please reset the Filter time only when you have replaced the filter, for a
suitable indication about the filter. For the filter replacement, see the section
"Air Filter" (SEE P34)
(continued on next page)
Downloaded From projector-manual.com Boxlight Manuals
30
PIN key in Operation
When the projector is turned on and
the PIN lock protection is set to[ on ] ,
the image will show for right side.
1.Press the MENU button on the
projector or remote control.Enter
PIN code by Keypad or Remote
control.
2.How to enter a PIN code?
Control panel use way
Remote control use way
CONTROL PANEL
BUTTONS
REMOTE CONTROL
BUTTONS
The control panel and remote control buttons to enter
a sequence of PIN code are the same with the photo.
MENU
(1) Press ◄ button : Select the [ 1 ] .
(2) Press ▲ button : Select the [ 2 ] .
(3) Press ► button : Select the [ 3 ] .
(4) Press ▼ button : Select the [ Enter ] move to next row.
(5) Press
(backspace) item :
In case to entered a wrong digit, select to delete the wrong digit you entered.
(6) Press
(backspace) item :
Once all four digits of the PIN been entered, select to confirm.
NOTE ►If the PIN is correct, projector will show normal image.
►If the PIN is incorrect, a “Enter new code” message will be showing. Please try
again.
►If the PIN been input incorrectly three times, a warning message will show up
and the projector will shut itself down after 20 seconds.
►If you lost the PIN completely, contact your dealer for help.
31
Downloaded From projector-manual.com Boxlight Manuals
Maintenance
Lamp
A lamp has finite product life. Reserving is recommended.
Replacing the lamp
1.Turn the projector off, and unplug the power cord. Allow the projector to cool for
at least 45 minutes.
2.If the projector is mounted on a ceiling, contact your local dealer to replace the lamp.
In case of replacement by yourself,
3
3.Remove the Lamp door.(marked by arrow)
4.Loosen 2 screws of the lamp holder.
Grasp the handle on the top of the lamp
and pull the lamp straight up out of the projector.
Lamp Door
5.Insert the new lamp, and retighten firmly the
2 screws of the lamp holder and lock the
Lamp Door.(marked by arrow)
screws
The Handle
4
5
Lamp Door
CAUTION ►Do not touch any inside of the projector, while the lamp is taken
out.
WARNING ►Do not touch the bulb. Touching the bulb will greatly decrease
the life of the lamp and could cause the bulb to explode.
NOTE ►Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
32
Downloaded From projector-manual.com Boxlight Manuals
Maintenance
Lamp Warning
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING ►The projector uses a high-pressure mercury glass lamp. The
lamp can break with a loud bang, or burn out, if jolted or scratched, handled
while hot, or worn over time. When the bulb bursts, it is possible for shards of
glass to fly into the lamp housing, and for gas containing mercury to escape
from the projector’s vent holes.
►About disposal of a lamp: This product contains mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
• For lamp recycling, go to www.lamprecycle.org. (in the US).
• For product disposal, contact your local government agency
or www.eiae.org (in the US) or www.epsc.ca (in Canada).
For more information, call your dealer.
Disconnect
the plug
from the
power
outlet
►If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
►If the lamp should break (it will make a loud bang when it does),
ventilate the room well, and make sure not to breathe the gas that
comes out of the projector vents, or get it in your eyes or mouth.
►Before replacing the lamp, turn the projector off and unplug the power
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the
lamp.
►Never unscrew except the appointed (marked by an arrow) screws.
►Do not open the lamp cover while the projector is suspended from
above. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
►Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
►Use only the lamp of the specified type.
►If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, contact your local dealer or a service representative.
►Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
►Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone
is poor, please replace the lamp as soon as possible. Do not use old
(used) lamps; this is a cause of breakage.
33
Downloaded From projector-manual.com Boxlight Manuals
Maintenance
Air Filiter
Please check and clean the air filter periodically. When the dialog have warning
message prompts you to clean the air filter, comply with it as soon as possible.
Replace the air filter when it is damaged or too soiled.
Replacing the air filter
When the used time reaches the filter counter
time,the projector will display message such
as” Filter Replace.Filter has been used more
than 100 hours.”
If the filter is difficult to clean or if it is
deteriorating, also ask the dealer to
replace the filter.
air filter
Iron net
filter cover
Screw
1.Turn the projector off, and unplug
the powercord. Allow the projector
to sufficiently cool down.
2.Remove the filter cover from
3
2
the right of projector.
3.Pull out the air filter.
4.Install the new air filter.
5.And then put the filter cover
Up
4
5
back on.
6.After please select the
Reset filter timer item of the
Security menu and display a
dialog.
6
Reset Filter Timer?
Select “No” to exit.
Lamp Reset
Yes
No
WARNING
►Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector.
NOTE
►If the internal temperature become too high because of filter blocked, the
projector may turn off itself to prevent the internal heat level rising.
34
Downloaded From projector-manual.com Boxlight Manuals
Maintenance
Other care
Inside of the projector
In order to ensure the safe use of your projector, please have it maintained
inspected by your dealer about once every year.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display
quality. After making sure that the projector is cool adequately, lightly wipe
the lens with a commercially available lens-cleaning wipe. Do not touch the
lens directly with your hand. Please handle with care.
NOTE ►After making sure that the projector is cool adequately, lightly wipe
the lens with a commercially available lens-cleaning wipe. Do not touch the
lens directly with your hand.
WARNING ►Before maintenance, make sure the power cable is not
plugged in, and then allow the projector to cool sufficiently. The care in a high
.
temperature state of the projector could cause a burn and/or malfunction to
the projector.
►Never try to maintain the inside of the projector by your self.
►Avoid wetting the projector or inserting liquids in the projector. It could
.
result in a fire, an electric shock, and/or malfunction to the projector
►Do not put anything containing water, cleaners or chemicals near the
projector.
►Do not use aerosols or sprays.
CAUTION ►Please take right care of the projector according to the
following. Incorrect care could cause not only an injury but adverse influence
such as discoloration, peeling paint, etc.
►Do not use cleaners or chemicals other than those specified in this manual.
►Do not polish or wipe with hard objects.
35
Downloaded From projector-manual.com Boxlight Manuals
Troubleshooting
Regarding the indicator lamps
When operation of the LAMP and POWER indicators differs from usual, check
and cope with it according to the following table. If the problem cannot be
resolved contact your dealer.
POWER
indicator
Blinking
In Green
LAMP
indicator
Conditions
off
Stand by
mode
Lighting
In Green
off
On mode
Lighting
In Green
Blinking
In Red
( Slow )
Cool down
mode
Projector is in cool-down mode and will not respond
to user input (normal)
Lighting
In Green
Blinking
In Red
( Fast )
Fan fault
mode
The projector has detected a problem with an
Slowinternal fan, the lamp will shut off automatically,
contact your dealer
Blinking
In Green
Lighting
In Red
Blinking
Blinking
In Green In Red
Description
Projector is ready to be turned on (normal)
Projector is on and operating normally
The lamp cover is open or there is a problem with
Lamp cover
the lamp. If the lamp door is closed and replacing
open
the lamp does not correct the issue, contact your
dealer.
High
temperature
The projector has overheated and shut itself down.
Correct the overtemp condition immediately.
1. Check that the ventilation slots are freefrom
obstructions
2. Check the cleanliness of the air filter.
WARNING ►Never use the projector if abnormal operations such as smoke,
strange odor, excessive sound, damaged casing or elements or cables,
penetration of liquids or foreign matter, etc. should occur. In such cases,
immediately disconnect the power plug from the power outlet. After making
sure that the smoke or odor has stopped, contact your dealer.
NOTE ► When the interior portion has become overheated, for safety
purposes, the projector is automatically shut down, and the indicator lamps
may also be turned off. In such a case, disconnect the power cord, and wait
at least 45 minutes. After the projector has sufficiently cooled down, please
make confirmation of the attachment state of the lamp and lamp cover before
turn the power on again.
36
Downloaded From projector-manual.com Boxlight Manuals
Troubleshooting
Mistaken for machine defects
About the phenomenon confused with a machine defect, check and cope with it
according to the following table.
Phenomenon
Cases not involving a machine defect
Reference
page
Correctly confirm the power cord.
The main power source has been interrupted during
operation such as by a power outage (blackout), etc.
Power does not
turn on.
Please disconnect the power plug from the power outlet,
and allow the projector to cool down at least 45 minutes,
then turn the power on again.
14
Either there is no lamp and/or lamp cover, or either
of these has not been properly fixed.
Please turn the power off and disconnect the power plug from
the power outlet, and allow the projector to cool down at least
45 minutes. After the projector has sufficiently cooled down,
please make confirmation of the attachment state of the lamp
and lamp cover, and then turn the power on again.
The signal cables are not correctly connected.
Correctly connect the connection cables.
Neither sounds
nor pictures are
outputted.
14
8
Signal source does not correctly work.
Correctly set up the signal source device by referring to the
manual of the source device.
(No video / audio) The input changeover settings are mismatched.
Select the input signal, and correct the settings.
The signal cables are not correctly connected.
Correctly connect the audio cables.
–
15
8
The MUTE function is set to on.
Sound does not
come out.
Restore the sound pressing the MUTE or VOLUME button
on the remote control.
The volume is adjusted to an extremely low level.
Adjust the volume to a higher level using the menu function
or the remote control.
The lens cover is not removed.
No pictures are
displayed.
15
Remove the lens cover.
The signal cables are not correctly connected.
Correctly connect the connection cables.
15
14
8
(continued on next page)
37
Downloaded From projector-manual.com Boxlight Manuals
Troubleshooting
Mistaken for machine defects (continued)
Phenomenon
Cases not involving a machine defect
Reference
page
The brightness is adjusted to an extremely low level.
Adjust BRIGHTNESS to a higher level using the menu
function or the remote control.
No pictures are
displayed.
(continued)
The computer cannot detect the projector as a plug
and play monitor.
Make sure that the computer can detect a plug and play
monitor using another plug and play monitor.
The BLANK screen is displayed.
Press the BLANK button on the remote control.
Video screen
display freezes.
Pictures appear
dark.
The Still function is set to on.
Press the Still button to restore the screen to normal.
The lamp is approaching the end of its product
lifetime.
21
–
19
19
32
Replace the lamp.
The focus is not properly adjusted.
Adjust the focus using the focus ring.
Pictures appear
blurry.
The lens is dirty or misty.
Clean the lens referring to the section “Caring for the lens”.
17
–
No battery
No remote
function
Before use the remote control,
please check battery of remote controller.
Remote signal be obstructed
Remove obstacle between projector and remote controller
Colors are pale
Color density and color matching are not correctly
adjusted.
12
13
–
Adjust the RGB setting.
Color lose.
Caused by poor VGA cable connection.
–
NOTE ► Although bright spots or dark spots may appear on the screen, this
is a unique characteristic of liquid crystal displays, and it does not constitute
or imply a machine defect.
38
Downloaded From projector-manual.com Boxlight Manuals
Troubleshooting
List of Supported Monitor Displays
Computer mode
Signal
Refresh Rate(Hz)
Resolution(dots)
VGA
60
640X480
VESA
60/72/75/85
640X480
SVGA
56/60/72/75/85
800X600
XGA
60/70/75/85
1024X768
SXGA
70/75
1152X864
SXGA
60/75
1280X960
SXGA
60
1280X1024
WXGA
60/75
1280 x 800
WXGA＋
60/75/85
1440 x 900
SXGA＋
60/75
1400 x 1050
UXGA
60
1600 x 1200
WSXGA＋
60
1680 x 1050
WUXGA
60
1920 x 1200
MAC
67
1280X1024 / 640x480
MAC
75
832x624
MAC
75
1024x768
MAC
75
1152x870
Signal
Refresh Rate(Hz)
Resolution(dots)
SDTV(480i)
30
720X480
SDTV(480p)
60
720X480
HDTV(720p)
60
1280X720
30
1920x1080
Signal
Refresh Rate(Hz)
Resolution(dots)
TV(NTSC)
60
720X480
TV(PAL,SECAM)
50
720X576
Component(YPbPr)
HDTV(1080i)
Composite/S-Video
39
Downloaded From projector-manual.com Boxlight Manuals
Appendix
Ceiling Mounted Installation Guide
Attach the optional ceiling mount at four-suspension bracket fixing points when
suspending from a ceiling.
A special method of installation is required in order to suspend the projector from
the ceiling. Please ask your dealer for more details.
Dimensions
Unit:mm
Screw Holes of Ceiling Mount
Screw : M4
Depth : 10 mm
92
96
92
90
90
92
92
96
360
480
360
160
160
479
N OT E
► Please use only with UL Listed ceiling mount bracket.
40
Downloaded From projector-manual.com Boxlight Manuals
Appendix
PIN Code Number Memo
Write down the PIN code number in the column below and keep it with this
manual securely. If you forgot or lost the number and unable to operate the
projector, contact the service station.
PIN Code Lock No.
Factory default set No: 0 0 0 0*
Logo PIN Code Lock No.
Factory default set No: 0 0 0 0*
*Should the four-digit number be changed,
the factory set number will be invalid.
41
Downloaded From projector-manual.com Boxlight Manuals