NetSafety Flamewatch Flame Detector-Video Combo Owner's Manual

The NetSafety Flamewatch Flame Detector-Video Combo is a powerful tool for monitoring and detecting fires, combining a flame detector with a video camera for comprehensive surveillance. With its advanced flame detection technology, it accurately identifies and responds to various types of fires, including hydrocarbon-based and hydrogen-based fires. The integrated video camera provides real-time visual confirmation of fire incidents, allowing operators to assess the situation and take appropriate action.
PDF
مستند
FLAME WATCH
FLAME DETECTOR
&amp; VIDEO CAMERA
Models:
FW-IR3S-A , FW-IR3S-R,
FW-IR3S-D, FW-IR3S-AD,
FW-UV/IRS-A, FW-UV/IRS-AR,
FW-UVS-A &amp; FW-UVS-AR
FW-IR3S-X Shown
Part Number: MAN-0079 Rev 01
December 2008
IMPORTANT INFORMATION
This manual is for informational purposes only. Although every effort has been made to ensure the correctness of the information, technical
inaccuracies may occur and periodic changes may be made without notice. Net Safety Monitoring Inc., assumes no responsibility for any error
contained within this manual.
This manual is guide for use of the Flame Watch unit (IR3S, UV/IRS or UVS model Flame Detector with the VID-C or VID-C-50 Video Camera)
and the data and procedures contained within this document have been verified and are believed to be adequate for the intended use of the device.
If the device or procedures are used for purposes other than as described in the manual without receiving prior confirmation of validity or
suitability, Net Safety Monitoring Inc. does not guarantee the results and assumes no obligation or liability.
No part of this manual may be copied, disseminated or distributed without the express consent of Net Safety Monitoring Inc.
Net Safety Monitoring Inc. products are carefully designed and manufactured from high quality components and can be expected to provide many
years of trouble free service. Each product is thoroughly tested, inspected and calibrated prior to shipment. Failures can occur which are beyond
the control of the manufacturer. Failures can be minimized by adhering to the operating and maintenance instructions herein. Where the absolute
greatest of reliability is required, redundancy should be designed into the system.
WARRANTY
Net Safety Monitoring Inc warrants this device against defective parts and workmanship for a period of for 36 months from date of purchase. No
other warranties or liability, expressed or implied, will be honoured by Net Safety Monitoring Inc.
Contact Net Safety Monitoring Inc. or an authorized representative for details.
We welcome your input at Net Safety Monitoring Inc. If you have any comments please contact us at the telephone number or address below or
visit our web-site, www.net-safety.com, and complete our on-line customer survey.
CONTACT INFORMATION
Net Safety Monitoring Inc
Corporate Headquarters
2721 Hopewell Place NE
Direct: (403) 219-0688
Facsimile: (403) 219-0694
E-mail: [email protected]
2
TABLE OF CONTENTS
APPENDIX ..................................................................................................... 13
IMPORTANT INFORMATION ............................................................................. 2
Appendix A: ELECTROSTATIC SENSITIVE DEVICE (ESD) .............. 13
WARRANTY ............................................................................................................. 2
CONTACT INFORMATION ......................................................................................... 2
Appendix B: RESISTANCE TABLE (OHMS)........................................... 14
SECTION 1: INTRODUCTION ............................................................................. 4
Description .............................. ............................................................................... 4
1.1 Flame Watch Dimensional Drawing ........................................................... 5
1.2 Mounting Flame Watch Unit ........................................................................ 6
1.3 Unpacking ...............................................................................................7
1.4 Field Installation......................................................................................7
1.4.1 Wiring .................................................................................................... 7
1.4.2 Grounding .............................................................................................. 7
1.4.3 Sealing .................................................................................................... 7
SECTION 2: CONNECTING FLAME WATCH................................................... 8
2.1 IR3S Flame Watch Junction Box Terminal Board ............................ ....8
2.2 UVS or UV/IRS Flame Watch Junction Box Terminal Board................9
2.3 DIP Switch (SW1) Positions..................................................................10
2.4 Troubleshooting ................................................................................ 11
2.5 Maintenance ...................................................................................... 11
2.6 How to Return Equipment .................................................................... 12
Appendix C: TECHNICAL SPECIFICATION OF VIDEO
CAMERA.................................................................................. 15
Appendix D: IR3S SPECIFICATION.......................................................... 16
Appendix E: UV/IRS SPECIFICATION..................................................... 17
Appendix F: UVS SPECIFICATION........................................................... 18
SECTION 1: INTRODUCTION
Description
Net Safety’s Flame Watch has two component products; a Flame Detector and Video Camera mounted as a unit. With this
combination and configuration the user is allowed to monitor a possible fire as well as intrusion in a specific coverage area.
Furthermore, the user is provided with options in selecting the model Flame Detector to be used with the Video Camera.
The FW-IR3S is the valuable integration of a multi-spectral (3IR) Infrared Flame Detector and a Video Camera which is mounted in
an explosion proof housing. The FW-UV/IRS and FW-UVS models are combinations of the Video Camera with the UV/IRS Flame
Detector or the UVS Flame Detector.
The (IR3S) Phoenix, Net Safety’s latest flame detection product, is a triple spectrum IR detector designed to respond to infrared radiation
emitted by a wide range of hydrocarbon based fires. Refer to the (IR3S) Phoenix’s manual (MAN-0044) for detailed operation.
The UV/IRS Flame Detector incorporates UV and IR detection circuitry to detect specific wavelengths in the UV and IR spectrum
whenever a fire is present. This detector is designed to detect a wide range of hydrocarbon based fires. Refer to MAN-0015 for detailed
operation. The UVS Flame Detector is also a member of Net Safety’s line of fire detection products and is designed to detect a wide range
of hydrocarbon, hydrogen and metal based fires. See MAN-0039 for more details.
The type of Flame Detector used, which determines the model Flame Watch, is dependent on the user’s choice, environment and application.
The VID-C or VID-C-50 explosion proof Video Camera is ideally suited for safety monitoring systems in hazardous locations. The colour video
camera is mounted in an explosion proof housing and delivers a composite video output for use with most VCR's or video monitors. The wide
viewing angle provides for large area of coverage by one camera. Refer to the Video Camera’s manual (MAN-0036) for detailed operation.
The Flame-Watch’s two components are available with standard explosion proof (XP) housing. As a result, the Flame-Watch provides integrated
security and performance required for high risk industrial installations.
4
1.1 Flame Watch Dimensional Drawing
Figure 1: Dimensional Drawing (Measurements are in Millimeters and Inches)
66.04
2.600
99.31
3.910
66.04
2.600
141.22
5.560
299.10
11.776
169.49
6.673
146.80
5.780
222.19
8.748
220.92
8.698
71.25
2.805
5
1.2 Mounting Flame Watch Unit
The Flame-Watch unit must be mounted and orientated exactly as shown below and be easily accessible for maintenance and calibration
purposes. Ensure the Flame-Watch unit is securely mounted, taking into consideration all requirements.
Figure 2: Mounting
Flame Detector
Junction Box
Video Camera
6
1.3 Unpacking
Remove all packaging components from the box. Carefully remove the Flame-Watch unit from its box and hold by the Junction box to
prevent damage. Use Net Safety’s lens cleaner to clean the lens of the Flame Detector and Video Camera before installation and operation.
WARNING:
The alignment of the Video Camera and Flame Detector has been factory set, care must be taken when
handling the Flame-Watch system. Do not hold or apply excessive force to the mounted video camera and flame detector.
1.4 Field Installation
WARNING:
Compliance with regulations is the responsibility of the installer. Wiring must comply with applicable regulations
relating to the installation of electrical equipment in a hazardous area.
1.4.1 Wiring
The use of shielded cable running through conduit is highly recommended for power input and signal wires to protect against interference caused
by extraneous electrical 'noise'. When cable is installed in conduit, the conduit must not be used for wiring to other electrical
equipment.
1.4.2 Grounding
Proper shielding and grounding procedures, for the specific area of installation, should always be followed.
1.4.3 Sealing
Water-proof and explosion-proof conduit seals are recommended to prevent the accumulation of moisture within the junction box.
Seals should be located as close to the device as possible and not more than 18 inches (46 cm) away. Explosion-proof installations
may require an additional seal where conduit enters a non-hazardous area. When pouring a seal, use a fibre dam to ensure proper
formation of the seal. Seals should never be poured at temperatures below freezing. The jacket and shielding of the cable shoul d be
stripped back to permit the seal to form around the individual wires. This will prevent air, gas and water leakage through the inside
of the shield and into the enclosure. It is recommended that explosion-proof drains and conduit breathers be used. Changes in
temperature and barometric pressure can cause 'breathing' which allows moist air to enter the conduit.
7
SECTION 2: CONNECTING FLAME WATCH
2.1 IR3S Flame Watch Junction Box Terminal Board
The type Flame Detector and hence model Flame Watch chosen will depend on the particular application, environment and response needed.
The IR3S model Flame Detectors available are analog, digital, analog/digital and relay. If the IR3S Flame Watch is being used , refer to Figure 3
and 4. The Flame Detector and Video Camera wires(except for the RCA cable) are factory fitted to the terminal board. User interface is made to
terminal blocks J4 and J5. The male RCA video ouput cable from the camera should be connected to the user’s video monitoring system.
For operational details on each product, see specific manual.
Relay
6
5
4
FAULT RELAY
Relay
3
2
1
ALARM RELAY
J5
ON
SW1
Earth
J4
1 2
OFF
Meter Test
Jacks
..
6
5
4
3
2
1
Earth
J5 not included
on FW-IR3S-A
Model
Note: The figure above is a general representation
of the Flame Watch terrminal board.
If only relays are being used, place jumper over
pins marked JP2.
FAULT RELAY
ALARM RELAY
FW-IR3S-D (digital unit)wiring
Designation/Function
Terminal J4
1
+Vin (Power +)
GND (Power -)
2
Not used
3
Not
used
4
Not
used
5
Earth
6
Designation/Function
Terminal J5
1
FW-IR3S-AD (analog/digital unit)wiring
A(Blue digital signal wire)
Terminal J4
Designation/Function
B(Brown digital signal wire)
2
1
+Vin (Power +)
Not used
3
4
Not used
GND (Power -)
2
5
Not used
SIG (4-20mA signal)
3
6
Not used
Not used
4
FW-IR3S-R (relay unit)wiring
5
Not used
Designation/Function
Terminal J4
Earth
6
1
+Vin (Power +)
Terminal J5
Designation/Function
GND (Power -)
2
1
A(Blue digital signal wire)
Not used
3
B(Brown digital signal wire)
2
Not used
4
3
Not used
5
Not used
Not used
4
Earth
6
Designation/Function
Terminal J5
5
Not used
6
1
(NO)Normally Open relay contact
Not used
COM (relay common)
2
Note: For IR3S-A and IR3S-AD, if isolated power
(NC)Normally Closed relay contact
3
(NO)Normally Open relay contact
configuration is being used, move jumper on IR3S
4
unit to EXT position and connect purple wire
COM (relay common)
5
(+ ISO wire) to external power supply. See IR3S
6
(NC)Normally Closed relay contact
manual.
Figure 4: Flame Watch Terminal Board.
JP2
Figure 3: Junction Box terminals for IR3S Flame detector
FW-IR3S-A (analog unit)wiring
Designation/Function
Terminal J4
1
+Vin (Power +)
GND (Power -)
2
3
SIG(4-20 mA signal)
Not used
4
5
Not used
Earth
6
8
2.2 UVS or UV/IRS Flame Watch Junction Box Terminal Board
The UVS or UV/IRS Flame Detector can be used instead of the IR3S Flame Detector as a part of the Flame Watch configuration.
The UVS or UV/IRS model Flame Detector is available as a analog unit or analog with relays. If the UVS or UV/IRS Flame Detector is
being used, refer to Figure 5 and 6 below. The detector and camera wires(except for the RCA cable) are factory fitted to the terminal board.
The terminal blocks (J4 and J5) are designated for user interface(power, output, etc). The male RCA video output cable from the camera should
be connected to the user’s video monitoring system. For operational details on each product, see specific manual.
5
4
Relay
3
2
1
Relay
ON
SW1
FAULT RELAY
6
Earth
J4
1 2
OFF
6
Meter Test
Jacks
..
5
4
3
2
1
Earth
Note: The figure above is a general representation
of the Flame Watch terminal board.
If only relays are being used, place jumper over
pins marked JP2
Fault Relay Alarm Relay
FW-UVS-AR or FW-UV/IRS-AR(analog/ralay unit)wiring
Designation/Function
Terminal J4
1
+Vin (Power +)
GND (Power -)
2
SIG(4-20 mA signal)
3
MVI (Manual VI)
4
5
Not used
Earth
6
Terminal J5
Designation/Function
(NO)Normally Open relay contact
1
COM (relay common)
2
(NC)Normally Closed relay contact
3
(NO)Normally Open relay contact
4
COM (relay common)
5
6
(NC)Normally Closed relay contact
J5
ALARM RELAY
FW-UVS-A or FW-UV/IRS-A(analog unit)wiring
Designation/Function
Terminal J4
1
+Vin (Power +)
GND (Power -)
2
3
SIG(4-20 mA signal)
MVI (Manual VI)
4
5
Not used
Earth
6
Figure 6: Flame Watch Terminal Board
JP2
Figure 5: Junction Box terminals for UVS or UV/IRS Flame detector
9
2.3 DIP Switch(SW1) Positions
The UVS-AR and UV/IRS-AR Flame Watch Terminal Board has a two position DIP Switch to define the Coil and Latch Status for the Fire Relay.
Refer to Figure 7 for DIP Switch positions.
The default setting for the Fire Relay is Normally De-energized/Non-latching. The Fault Relay is factory set to Normally Energized/Non-latching and
cannot be modified.
Figure 7: SW1 DIP Switch positions
Coil and Latch Status
Fire Relay
Position 1
Position 2
De-energized / Non-latching
ON
ON
Energized / Non-latching
ON
OFF
De-energized / Latching
OFF
ON
Energized / Latching
OFF
OFF
The IR3S Flame Watch Terminal Board doesn’t have selectable DIP swithes on the junction box terminal board. Relay conditions and coil status are
determined by the DIP Swithes and jumper on the electronic IR3S Flame Detector module, see the IR3S manual (MAN-0044).
10
2.4 Troubleshooting
The Flame Watch is not designed to be repaired in the field. If a problem should develop, carefully check for correct
wiring and refer to individual product manuals. If it is determined that the problem is caused by an electronic defect,
the device should be returned to the factory for repair. See ‘How to Return Equipment’.
2.5 Maintenance
To ensure reliable viewing and detecting, it is important to periodically clean the camera and flame detector window. Although
the frequency of this cleaning is determined by the requirements of the particular process, it is recommended that the Flame Watch
(flame detector and camera) be cleaned every year. See individual product manuals on maintenance.
11
2.6 How to Return Equipment
A Material Return Authorization number is required in order to return this equipment. Please contact Net Safety Monitoring at (403) 2190688 before returning equipment or consult our Service Department to possibly avoid returning equipment.
If you are required to return equipment, include the following information:
1
2
3
4
5
A Material Return Authorization number (provided over the phone to you by Net Safety).
A detailed description of the problem. The more specific you are regarding the problem, the more quickly our Service department can
determine and correct the problem.
A company name, contact name and telephone number.
A Purchase Order, from your company, authorizing repairs or request for quote.
Ship all equipment, prepaid to:
Net Safety Monitoring Inc
2721 Hopewell Place NE
Calgary, Alberta, Canada
T1Y 7J7
6.
Mark all packages: RETURN for REPAIR
7.
Waybills, for shipments from outside Canada, must state:
Equipment being returned for repair
All charges to be billed to the sender
Please also ensure a duplicate copy of the packing slip is enclosed inside the box indicating item 1-4 along with the courier and account number
for returning the goods.
All Equipment must be Shipped prepaid. Collect shipments will not be accepted.
Pack items to protect them from damage and use anti-static bags or aluminum-backed cardboard as protection from electrostatic discharge.
12
APPENDIX
Appendix A: ELECTROSTATIC SENSITIVE DEVICE - ESD
Electrostatic discharge (ESD) is the transfer, between bodies, of an electrostatic charge caused by direct contact or induced by an electrostatic
field.
The most common cause of ESD is physical contact. Touching an object can
cause a discharge of electrostatic energy—ESD! If the charge is sufficient and
occurs near electronic components, it can damage or destroy those components.
In some cases, damage is instantaneous and an immediate malfunction occurs.
However, symptoms are not always immediate—performance may be marginal
or seemingly normal for an indefinite period of time, followed by a sudden
failure.
To eliminate potential ESD damage, review the following guidelines:
x
x
x
x
x
x
Handle boards by metal shields—taking care not to touch electronic components
Wear grounded wrist or foot straps, or ESD shoes or heel grounders to dissipate unwanted static energy
Prior to handling boards, dispel any charge in your body or equipment
Ensure components are transported and stored in static safe packaging
When returning boards, carefully package in the original carton and static protective wrapping
Ensure ALL personnel are educated and trained in ESD Control Procedures
In general, exercise accepted and proven precautions normally observed when handling electrostatic sensitive devices.
A warning label is placed on the packaging, identifying product using electrostatic sensitive semiconductor devices.
13
Appendix B: RESISTANCE TABLE (OHMS)
Note: Resistance shown is one way. This figure should be doubled when determining closed loop resistance.
Distance AWG #20
(Feet)
100
200
300
400
500
600
700
800
900
1000
1250
1500
1750
2000
2250
2500
3000
3500
4000
4500
5000
5500
6000
1.02
2.03
3.05
4.06
5.08
6.09
7.11
8.12
9.14
10.20
12.70
15.20
17.80
20.30
22.80
25.40
30.50
35.50
40.60
45.70
50.10
55.80
61.00
AWG #18
0.64
1.28
1.92
2.55
3.20
3.83
4.47
5.11
5.75
6.39
7.99
9.58
11.20
12.80
14.40
16.00
19.20
22.40
25.50
28.70
32.00
35.10
38.30
AWG #16
0.40
0.80
1.20
1.61
2.01
2.41
2.81
3.21
3.61
4.02
5.03
6.02
7.03
8.03
9.03
10.00
12.00
14.10
16.10
18.10
20.10
22.10
24.10
AWG #14
0.25
0.51
0.76
1.01
1.26
1.52
1.77
2.02
2.27
2.53
3.16
3.79
4.42
5.05
5.68
6.31
7.58
8.84
10.00
11.40
12.60
13.91
15.20
AWG #12
0.16
0.32
0.48
0.64
0.79
0.95
1.11
1.27
1.43
1.59
1.99
2.38
2.78
3.18
3.57
3.97
4.76
5.56
6.35
7.15
7.94
8.73
9.53
AWG #10
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.09
1.25
1.50
1.75
2.00
2.25
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
AWG #8
0.06
0.13
0.19
0.25
0.31
0.38
0.44
0.50
0.57
0.63
0.79
0.94
1.10
1.26
1.41
1.57
1.88
2.21
2.51
2.82
3.14
3.46
3.77
14
Appendix C: Technical Specifications of Video Camera.
(Refer to the VID-C/VID-C-50 manual(MAN-0036) for more detailed description of its operations and specifications)
Operating Voltage:
10.5 VDC to 32 VDC
Power Consumption (at 24 VDC):
2.0 Watts nominal.
70 mA nominal.
Operating Temperature:
-25oC to +60oC (-13oF to +140oF).
Storage Temperature:
-40oC to +60oC (-40oF to +140oF).
Resolution:
Horizontal 420 TV lines.
Number of Pixels:
Effective pixels: 512(H) 429(V)
Camera Enclosure Material:
Powder coated or anodized aluminum (Optional Stainless Steel).
Certification:
Housing is certified to CSA. Certified ratings are; NEMA 4X for environmental protection and CSA,
Class I, Division 1 Groups B, C and D for hazardous locations.
Viewing Angle:
o
VID-C (3.6 mm Lens): Horizontal 52o , VID-C-50 (25 mm Lens): Horizontzal 9.14 with a scene of
8 feet by 10 feet located at a distance of 50 feet from the camera.
S/N (Signal to Noise ratio):
&gt; 48dB.
Output:
1Vp-p, 75 ohms composite signal (NTSC).
Connector:
Standard RCA Video Signal Connector.
15
x D : IR3S SPECIFICATION
Appendix
A
IR3S-A
A (Analog)
Models
I3RS-R (R
Relay)
IR3S-AD (Analo
og/Digital)
1 to 32 VDC measu
10
ured at the detector
Operating Volttage
Power Consumpttion
(@ 24V
Vdc)
0.72W
Nominal 30mA/
3
Maximum 64mA/ 1.44W
De-Energized: Nom
D
minal 39mA/0.96W. Maximum 73mA// 1.68W
E
Energized:
Nomina
al- 51mA, =1.20w). Maximum- 86mA, 2.16W
A/ 0.72W
Nominal 30mA
Maximum 64mA/ 1.44W
Power Consumpttion
Vdc)
(@ 12V
4
0.60W
Nominal 45mA/
Maximum 113mA/
1
1.32W
D
De-Energized:
Nom
mA/ 1.68W
minal- 66mA/0.84W
W. Maximum- 138m
Energized: Nomina
E
al- 93mA, =1.08w)
M
Maximum165mA,, 2.04W
A/ 0.60W
Nominal 45mA
Maximum 113m
mA/ 1.32W
In Rush Currrent
(at 24V
Vdc)
Outtput
Up
p to 2.6 A for 2.ms (va
aries with power supp
ply)
0 to 20 mA – In
nto a max loop
impedance of 800Ohms @
Ohms @ 11.0Vdc.
32Vdc or 150O
Non-Isolated loop
l
supply
0 to 20 mA – Into a max
m loop
Normally open/Norm
N
mally closed contacts rated
for 5A @ 30Vdc//125Vac.
r
S
Selectable
energized/ de-energized Fire rela
ay. Fault relay ę&iexcl; as energized and
b
both
ys ę&iexcl; as non-latchiing
Fire &amp; Fault relay
iimpedance of 800Ohm
ms @ 32Vdc or
1150Ohms @ 11.0Vdc. Non-Isolated
lloop supply.
R
RS-485 RTU Modbus protocol.
Field of View
V
Spectral Ra
ange
Time Deelay
FM Perfo
ormance tested: 100&deg; horizontal / 100&deg; verttical @ 50% of the on-a
axis detection distancce for N-Heptane.
0&deg; horizontal / 70&deg; verttical at a distance of 200Ğ(
2
mance tested)
70
Not FM Perform
measures at three
t
d Wavelengths
distinct Infrared
The IR3S ęre detector
d
DIP switch selectablle 0, 3, 5, 10 seconds,
Sensitivity Ĵiings
Two (2)
( adjustable sĴing via
v DIP switch (High
h/Low)
Temperature/ RH
FM Certęd (-40&deg;C
C to +75&deg;C / -40&deg;F to 167&deg;F). Operational (--50&deg;C to +75&deg;C / -58&deg;F
RH non condensing
F to 167&deg;F). 0 – 95% R
Metallurgy &amp; IP/Neema
Ratiings
Weight (with swivel)
o SS316 (factory sealed housing). IP66 an
Aluminum or
nd NEMA 4X
2
2.1Kg
/4.5lbs (SS316 Option
O
@ 3.4Kg/ 7.5lbss)
Performance cęd
c
to: Class3260, ANSI/NEMA 250, and IEC60529.
Approv
vals
D, T5. Ex d IIB+H2 T5
5. Class I, Zone 1, Grp
ps IIB+H2, T5; Nema 4X,
4 IP66. For CANAD
DA ONLY, Class I, Diiv 1, Grps A
US Class I, Div 1, Grps BCD
(Canada ONLY
Y – with special cemeenting), BCD, T5. Ex d IIB+H2 T5.
Performaance certified by FM
N
NOTE:
F with maximu
um sensitivity settting and zero seco
ond time delay.
16
APPENDIX E :
odels
Mo
UV/IRS SPECIFICATION
UV/IRS-A
A (Analog)
n
Power Consumption
UV/IRS-AR (An
nalog/Relay)
10 to 32 VDC
Operating Voltagee
At 10Vdc: Nom
minal 95mA/ 0.95W.. Maximum 225mA
A/ 2.25W
*With Heater: Nominal
N
200mA/ 2.0W. Maximum 345
5mA/ 3.45W
At 10Vdc: Nomina
al 95mA/ 0.95W. M
Maximum 225mA/ 2.25W
2
*With Heater: Nom
minal 200mA/ 2.0W
W. Maximum 335m
mA/ 3.35W
At 24Vdc: Nom
minal 45mA/ 1.1W. Maximum 115mA// 2.76W
*With Heater: Nominal
N
90mA/ 2.16W. Maximum 165
5mA/ 3.96W
al 45mA/ 1.1W. Maaximum 115mA/ 2..76W
At 24Vdc: Nomina
*With Heater: Nom
minal 90mA/ 2.16W
W. Maximum 165m
mA/ 3.96W
At 32Vdc: Nom
minal 35mA/ 1.12W.. Maximum 105mA
A/ 3.36W
N
70mA/ 2.24
4W. Maximum 145
5mA/ 4.64W
*With Heater: Nominal
At 32Vdc: Nomina
al 35mA/ 1.12W. M
Maximum 105mA/ 3.36W
3
W. Maximum 145m
mA/ 4.64W
*With Heater: Nom
minal 70mA/ 2.24W
In Rush Currentt
1.5A for 22ms
Current Outputt
0 to 20 mA – Intto a max loop impeda
ance of 800Ohms @ 32
2Vdc or 150Ohms @ 11.0Vdc. Non-Isolated
d loop supply
Relay Outputt
Field of View
w
Spectral Rangee
Time Delay
y
Form C contacts rateed 1A @ 30Vdc, 0.5A @
@125Vac. Selectable energized/
e
deenergized, latching/ non-latching Fire relaay. Fault relay ę&iexcl; as
a energized/
non-latching
N
N/A
120&deg; Horizon
ntal, 95&deg; Vertical @ 50%
% of maximum on axiis distance.
0 to 2600 angstroms); IR
I radiation in the 4.4
4micron range
UV radiation over the range of 185 to 260
2 nanometres (1850
DIP switch selectablee 0, 3, 5, 7 seconds,
Sensitivity Ĵgss
DIP swiitch selectable 8, 16, 24
4 or 32 counts per secconds
Temperature &amp; RH
H
FM Certęd (-40&deg;C to
t +75&deg;C / -40&deg;F to 167
7&deg;F). Operational (-5
50&deg;C to +75&deg;C / -58&deg;F to
t 167&deg;F). 0 – 95% RH
H non condensing
A
Meetallurgy &amp; IP/NEMA
Weight (with swivel))
d housing). IP66 and NEMA 4X
Aluminum orr SS316 (factory sealed
ption @ 3.4Kg/ 7.5lbs)
2.1
1Kg /4.5lbs (SS316 Op
2
and IEC60529.
FM Performan
nce certę to: Classs3260, ANSI/NEMA 250,
Approvalss
Class I, Div
D 1, Grps A,B,C,D, T5.
T
Ex d IIB+H2 T5. Class I, Zone 1, Grpss IIB+H2 T5; Nema 4X
X, IP66.
Performance certified by
b FM with maximum sensitivity
y setting and zerro second time delay
N
NOTE:
17
ENDIX F:
APPE
Models
UVS SPECIFICATION
S-AR (Analog/Reelay)
UVS
UVS-A (Analo
og)
10 to 32 VDC
Operrating Voltage
Power Consumption
1
2
Nominal 95mA/ 0.95W. Max 225mA/
2.25W
At 10Vdc:
335mA/ 3.35W
*Wiith Heater: Nomina
al 200mA/ 2.0W. Maximum
M
3
At 10V
Vdc: Nominal 95mA
A/ 0.95W. Max 2255mA/ 2.25W
*With Heater: Nominal 200mA/
2
2.0W. Max
ximum 335mA/ 3.35
5W
2
5mA/ 1.1W. Max 11
Nominal 45
At 24Vdc:
15mA/ 2.76W
165mA/ 3.96W
*Wiith Heater: Nomina
al 90mA/ 2.16W. Maximum
M
3
Vdc: Nominal 45mA
At 24V
A/ 1.1W. Max 95m
mA/ 2.28W
*With Heater: Nominal 90mA/
9
2.16W. Max
ximum 145mA/ 3.48
8W
3
At 32Vdc:
Nominal 35
5mA / 1.12W. Max 105mA/ 3.36W
*Wiith Heater: Nomina
al 70mA/ 2.24W. Maximum
M
140mA/ 4.48W
4
At 32V
Vdc: Nominal 35mA
A/ 1.12W. Max 80m
mA/ 2.56W
2.24W. Max
*With Heater: Nominal 70mA/
7
ximum 115mA/ 3.68
8W
In Rush Current
1.5A for 22ms
urrent Output
Cu
x loop impedance of 800Ohms
@ 32Vdc or 150Ohms @ 11.0Vdc. Non-Isolated loop su
0 to
t 20 mA – Into a max
8
upply
Relay Output
Field of View
Spectral Range
Time Delay
Form C contacts rated 1A @ 30Vdc, 0.5A @125Vacc. Selectable energizeed/ deenergiz
zed, latching/ non-latcching Fire relay. Faullt relay ę&iexcl; as energ
gized/
non-lattching
N/A
120&deg;&deg; Horizontal, 95&deg; Vertiical @ 50% of maximu
um on axis distance.
nge of 185 to 260 nano
ometres (1850 to 2600 angstroms)
UV radiation
r
over the ran
DIP swittches selectable 0, 3, 5,
5 7 seconds.
Sensittivity Ĵ
DIP switch selectable 8, 16, 24 or 32 counts
c
per seconds
Temp
perature &amp; RH
FM Cerrtięed (-40&deg;C to +75&deg;C
C / -40&deg;F to 167&deg;F). Operational
O
(-50&deg;C to +75&deg;C
+
/ -58&deg;F to 167&deg;F
F). 0 – 95% RH non co
ondensing
Metallurgy
y &amp; IP/NEMA
Weight (with swivel)
or SS316 (factory
A
Aluminum
(
sealed housin
ng). IP66 and NEMA
A 4X
2.1Kg /4.5
5lbs (SS316 Option @ 3.4Kg/
3
7.5lbs)
P
certęd
FM Performance
d to: Class3260, ANSII/NEMA 250, IEC6052
29.
Approvals
Classs I, Div 1, Grps A,B,C
C,D, T5. Ex d IIB+H2 T5. Class I, Zone 1, Grps
G
IIB+H2 T5; Nema
a 4X, IP66.
ce
NOTE: Performance
P
ertified by FM with maximum se
ensitivity setting and zero secon
nd time delay
18
NetȱSafetyȱMonitoringȱInc.ȱȱ
2721ȱHopewellȱPlaceȱNE,ȱCalgary,ȱABȱCanadaȱT1Yȱ7J7ȱȱ
1Ȭ866ȬFIREGASȱ(347Ȭ3427)ȱ|ȱph.ȱ(403)ȱ219Ȭ0688ȱ|ȱfx.ȱ(403)ȱ219Ȭ0694ȱȱ
http://www.netȬsafety.comȱ|ȱEmail:ȱnsmsales@netȬsafety.comȱ
PRODUCTȱSERVICESȱCONTACTȱINFORMATIONȱȱ
Telephoneȱ[ȱ8amȱȬȱ5pmȱMDTȱ]:ȱ(403)ȱ769Ȭ6074ȱ|ȱ(403)ȱ717Ȭ8219ȱȱ
Fax:ȱ(403)ȱ219Ȭ0694ȱȱȱEmail:ȱproductservices@netȬsafety.comȱȱ
http://www.netȬsafety.com/service/product_services.htmlȱ
">
مرحباً! أنا روبوت دردشة يعمل بالذكاء الاصطناعي تم تدريبي خصيصًا لمساعدتك في NetSafety Flamewatch Flame Detector-Video Combo Owner's Manual. لقد قمت بمراجعة المستند بدقة ويمكنني مساعدتك في تحديد موقع المعلومات التي تحتاجها بالضبط أو شرح المحتوى بعبارات واضحة و بسيطة. سواء كنت تبحث عن إرشادات حول ميزات معينة أو خطوات استكشاف الأخطاء وإصلاحها أو الاستخدام العام، فلا تتردد في طرح أسئلتك. كلما قدمت المزيد من التفاصيل حول مخاوفك أو احتياجاتك، زادت دقة و فعالية مساعدتي لك!