PROFESSIONAL
SERIES
Owner’s Guide
For Models:
CA 6551
CA 6551 SST
Deluxe Vehicle Security and
Remote Start System with 2 Way
Confirming LCD Remote Control
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
2010 Audiovox Electronics Corporation. All rights reserved.
1
2
Table of Contents
Using Your Remote Control ............................................................... 3
Arming the Security System ............................................................ 3
Passive Arming Bypass ................................................................... 3
Bypassing the Shock Sensor .......................................................... 3
Hidden Alarm Function ...................................................................... 3
Disarming the Security System ........................................................ 3
Two Stage Door Unlock (optional) ................................................... 4
Activating Trunk Release (optional) ................................................ 4
Activating Optional AUX 1 (optional) ............................................... 4
Using the Progressive Car Finder Feature ...................................... 4
Using the Personal Protection Alarm ............................................... 4
Programmed Transmitter Notification .............................................. 4
Valet Mode ........................................................................................ 5
Eliminating Arm / Disarm Notification Chirps .................................... 5
Manually Overriding the Security System ....................................... 5
Car Jack Mode .................................................................................. 6
Using Your Remote Vehicle Starter ................................................. 6
Remote Starting Your Vehicle .......................................................... 6
Remote Start Shutdown ................................................................... 6
Entering Your Vehicle while it is Running via Remote Start ........... 7
Preheating or Precooling the Vehicle’s Interior ............................... 7
User Programmable Run Time / Run Time Extension ...................... 7
Using the “Quick-Stop” Feature ....................................................... 7
Operating the 2 / 3 Hour Start Up Timer Mode ................................ 8
Turbo Timer Mode (optional) ............................................................ 8
Operating the Daily Start Timer ........................................................ 9
Remote Start Safety Features ......................................................... 9
LED and Siren/Horn Indications ....................................................... 10
Additional 2-Way LCD Remote Control Functions ...................... 11
LCD Remote Control ICON’s ............................................................ 13
Transmitter Button Functions ......................................................... 14
Replacing Remote Control Batteries ............................................. 16
Warranty Information ......................................................................... 17
2010 Audiovox Electronics Corporation. All rights reserved.
Using Your Remote Control
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The
LED status indicator will blink steadily, once per second.
NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle.
Passive Arming Bypass
If passive arming is enabled on your system, while the system is disarmed, press
+ , the system will respond with 1 chirp and the LED will turn on. The security system will remain in this temporally bypassed state for as long as you wish. To exit passive bypass, press the or button and the system will return to normal status.
Bypassing The Shock Sensor
To arm the system and ignore the shock sensor press button, then within 5 seconds press + , the system will respond with 1 long chirp.
NOTE: The system will only change the shock sensor setting for one arm cycle and will be defaulted back to normal operation the next time the system is armed.
Hidden Alarm Function
Press the button first, within 3 seconds press the button to activate the hidden alarm function. The security system will arm with “Hidden Alarm Function” in which the siren / horn will be silenced if the system is triggered.
Disarming the Security System
To disarm the system press the button. The parking lights will flash 1 time, indicating the system is disarmed and has unlocked the doors (if equipped and connected).
NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle. If your system is set up for 2 step unlock, a third press of will activate the audible response.
*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more than 2 seconds.
2010 Audiovox Electronics Corporation. All rights reserved.
3
4
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the button for 3 seconds will open the vehicle’s trunk or hatch.
Activating Optional AUX 1 (Optional)
If this feature is enabled on your system, pressing the and buttons simultaneously will activate an optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system.
Using the Progressive Car Finder Feature
Press the button to locate your vehicle. The system will sound 5 times at low volume, increasing in volume each time the button is pressed.
Using the Personal Protection Alarm (Panic)
Press and hold the button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s and buttons can be used to lock and unlock the door (if the option is installed). To stop the alarm, press and hold the button on the transmitter again for 3 seconds. The system will automatically stop after 30 seconds.
Programmed Transmitter Notification
As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.
2010 Audiovox Electronics Corporation. All rights reserved.
Valet Mode
When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the 4 steps outlined below:
1.
Turn the vehicle’s ignition ON.
2.
Push and hold the programming/valet button.
3.
The LED will turn on solid when valet mode is active
4.
Release the programming/valet button.
Eliminating Arm / Disarm Notification Chirps
System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks.
1.
Turn the ignition ON then OFF.
2.
Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.
Manually Overriding the Security System
Your system can be disarmed without the use of the transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system;
1.
Open the vehicle door. The alarm will sound.
2.
Turn the ignition key to the ON position.
3.
Within 10 seconds, press and release the valet push button switch.
The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally.
2010 Audiovox Electronics Corporation. All rights reserved.
5
6
Car Jack Mode
This feature must be turned on in system programming, please consult your installing dealer.
Triggering Car Jack mode: While the ignition is ON and press and hold + for 2 seconds, the parking lights will flash 1 time and the system will act as follows;
1.
50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode. If Car Jack mode is not turned off at this time it will advance to the next step.
2.
Following the 15 second chirps (total time now 65 seconds) the siren will go into full sound and the parking lights will start flashing.
3.
90 seconds after trigger in, addition to the siren and parking lights, the system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS
STATE UNTIL THE BATTERY IS DEPLETED.
OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF then On and press the valet button within 10 seconds.
Using Your Remote Vehicle Starter
Remote Starting Your Vehicle
To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process.
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle off.
2010 Audiovox Electronics Corporation. All rights reserved.
Entering the Vehicle while it is Running via Remote Vehicle Start
1.
Unlock the vehicle’s doors.
2.
Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3.
Insert the key into the ignition switch and turn to the ON or RUN position.
4.
Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle’s interior to your setting.
User Programmable Run Time / Run Time Extension
The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes. Follow the steps below to extend the vehicle’s run time.
1.
The remote start must already be active.
2.
Press and release the button 4 times.
3.
The system will chirp to confirm that the run time has been reset.
Using the “Quick-stop” Feature
If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you.
To engage quick stop:
1.
Stop the vehicle and place the transmission in PARK.
2.
With your foot off the brake pedal, press and release the button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered.
3.
Remove the keys from the ignition and exit the vehicle. Press the
button to lock the vehicle’s doors if desired.
Note: Do not leave children or animals unattended in the vehicle when using the quick-stop feature.
2010 Audiovox Electronics Corporation. All rights reserved.
7
Operating the 2 / 3 Hour Start Up Timer Mode
The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour is made in option programming.
WARNING!
Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.
8
To begin the 2 / 3 hour start up timer mode:
1.
Turn the vehicle’s ignition ON then OFF.
2.
Press and hold the valet button.
3.
Press the button 4 times, the system will; a.
When set for 3 Hour (default) - chirp 2 times and flash the parking lights 4 times.
b.
When set for 2 Hour - chirp 1 time and flash the parking lights 2 times.
4.
Release the valet button.
To exit the 2 / 3 hour start up timer mode:
1.
Turn the vehicle’s Ignition ON.
OR
1.
Activate the remote vehicle start feature using the remote control.
Turbo Timer
This option will keep the engine running to allow the vehicle’s turbo to properly cool down before shutting the engine off.
To engage the Turbo Timer feature:
1.
With the vehicle running via the ignition key and your foot off of the brake pedal.
2.
Engage the vehicle’s parking brake and press the and buttons simultaneously.
3.
The vehicle’s parking lights will turn on to verify the Turbo Timer feature has been activated.
4.
Turn the ignition key OFF, the vehicle will continue to run until the preprogrammed time has elapsed (1, 3, or 5 minutes)
To disengage the turbo timer feature, press the vehicle’s brake pedal.
2010 Audiovox Electronics Corporation. All rights reserved.
Operating the Daily Start Timer
The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process.
1.
Turn the ignition ON/OFF (vehicle must be disarmed).
2.
Within 10 seconds, while pressing the brake, press and release the button twice.
3.
The vehicle will emit 2 chirps.
Remote Start Safety Features
For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur:
1.
The vehicle hood is open.
2.
The brake pedal is pressed prior to turning the ignition key to the ON position.
3.
The engine is over-revved (tach checking only).
4.
Valet mode is active.
2010 Audiovox Electronics Corporation. All rights reserved.
9
10
LED and Siren/Horn Indications
LED Display Indications
LED
OFF
SLOW FLASH
FAST FLASH
ON (SOLID)
2 FLASH... PAUSE
3 FLASH... PAUSE
4 FLASH... PAUSE
5 FLASH... PAUSE
Function
DISARMED
ARMED
PASSIVE ARMING
VALET MODE
ZONE 2 TRIGGER, HOOD/TRUNK
ZONE 3 TRIGGER, DOOR
ZONE 4 TRIGGER, SHOCK
ZONE 5 TRIGGER, IGNITION
Siren/Horn Indications
Chirps
1
4
5
2
3
Function
DISARM
ARM
DOOR AJAR UPON ARMING
DISARM / TRIGGERED
CAR LOCATOR
Parking Light Flash Indications
Flashes Function
1 DISARM
2
3
5
ARM
DISARM / TRIGGERED
CAR LOCATOR
ON (SOLID) REMOTE STARTED
2010 Audiovox Electronics Corporation. All rights reserved.
Additional 2-Way LCD Remote Control Functions
Check Vehicle Status
Press and release 2 times then press within 3 seconds, the transmitter will respond with one melody sound and display the current status of the vehicle.
Display Illumination
Press and hold the button for 1 second. The display will illuminate for 5 seconds.
Melody / Vibration Mode
To have the remote control vibrate, play a melody tone or both each time it receives a response from the vehicle press and release then press and hold for 2 seconds.
Button Beeps
To toggle button beeps on or off press and release then press and hold for 2 seconds.
Battery Save Mode
While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any incoming signals from the main unit until a button is pressed. The LCD screen will display SAVE to indicate that power save mode is ON. To enter power save mode press and hold for 5 seconds.
Clear Flashing Icons and Melody Sound
Press the button 3 times within 3 seconds. This will clear the melody sound and flashing icons on the LCD screen.
Stopping LCD Trigger Melody
To stop the alarm trigger melody if the system has been triggered WITHOUT disarming the system, press any button one time only, this will not send a command to the vehicle at this time and the alarm will continue to sound.
2010 Audiovox Electronics Corporation. All rights reserved.
11
12
Button Lock
Press and release then press hold the for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked.
Illumination
Press and release 2 times then press and hold for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command.
2 Car Mode
To control a second security system enter 2 car mode by pressing then press and together for 3 seconds. When the icon appears on the transmitter’s LCD screen it will control the second security system. Use the same method to exit 2 car mode and resume control of the original vehicle’s security system.
NOTE: A second security system must be installed and the LCD transmitter must be learned to it before this feature will operate the additional system.
Parking Meter Countdown
The parking meter countdown timer has 6 preset times, to access the preset times and begin countdown press and release then press and hold for 2 seconds, each additional press of will increase the countdown time.
Adjusting the Clock and Timer Settings
The clock, alarm clock and programmable countdown timer are accessed through the Function Menu. Press and hold for 3 seconds to access the function menu, once you have accessed the feature menu press and release to scroll through each feature and follow the steps below to adjust the settings for each. Press and hold for 2 seconds to exit the menu.
Clock Hour
Clock Minute
Alarm Clock Hour
Alarm Clock Minute
Press
Press
Press
Press
to increase or to decrease
to increase or to decrease
to increase or to decrease
to increase or to decrease
Alarm Clock ON / OFF
Countdown Timer Hour
Countdown Timer Minute
Press
Press
Press
to turn ON or to turn OFF
to increase or to decrease
to increase or to decrease
Countdown Timer ON / OFF Press to turn ON or to turn OFF
2010 Audiovox Electronics Corporation. All rights reserved.
LCD Remote Control ICON’s
LOCK
SYSTEM ARMED
TRANSMITTING
TRUNK TRIGGER
HOOD TRIGGER
SYSTEM TRIGGER
BATTERY INDICATOR
VIBRATE/SILENT MODE
2 CAR MODE
ALARM CLOCK
TIMER START MODES
UNLOCK
VALET MODE
IGNITION ON/TRIGGER
DOOR TRIGGER
FULL SHOCK TRIGGER
TIME COUNT DOWN
BATTERY SAVE MODE
MELODY MODE
TIME DISPLAY
ENGINE RUNNING
AUX 1 OUTPUT
2010 Audiovox Electronics Corporation. All rights reserved.
13
14
Transmitter Button Functions
1 Way
Transmitter
Lock Unlock
Panic
Lock X
Unlock X
2 Step Unlock X
Trunk X
X
X
Car Finder
Panic
Remote Start
Remote Start
Shutdown
Run Time
Extention
AUX 1
Shock Bypass
Hidden Alarm
Passive Arming
Bypass
Turbo Timer
2 / 3 Hour Start
Daily Start Timer
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Press and Release
Press and Release
Press and Release 2 times
Push and Hold (3 Sec)
Press and Release
Push and Hold (3 Sec)
Press and Release (1 or 2 times depending on selectable option)
Push and Hold (3 Sec)
Press and Release 4 times.
Push and Hold (3 Sec)
Press and Release Lock then
Press Lock + Car Find
Press and Release Car Fnd then
Press Lock
Press and Release
Press Unlock + Start
Ignition ON/OFF, Press and Hold
Valet Button, Press Start 4 times
Press Lock + Start
2010 Audiovox Electronics Corporation. All rights reserved.
Panic
Remote Start
Remote Start
Shutdown
Run Time
Extention
AUX 1
Shock Bypass
Hidden Alarm
Passive Arming
Bypass
Turbo Timer
2 / 3 Hour Start
Daily Start Timer
Menu
2 Way
Transmitter
Car Find /
Lock Unlock
Panic
Lock X
Unlock X
Start
2 Step Unlock
Trunk
Car Finder
X
X
X
Function Operation Method
Press and Release
Press and Release
Press and Release 2 times
Push and Hold (3 Sec)
Press and Release
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Push and Hold (3 Sec)
Press and Release (1 or 2 times depending on selectable option)
Push and Hold (3 Sec)
Press and Release 4 times.
Push and Hold (3 Sec)
Press and Release Lock then
Press Lock + Car Find
Press and Release Car Fnd then
Press Lock
Press and Release
Press Unlock + Start
Ignition ON/OFF, Press and Hold
Valet Button, Press Start 4 times
Press Lock + Start
Press and Hold
2010 Audiovox Electronics Corporation. All rights reserved.
15
Replacing Remote Control Batteries
1 Way 4 Button Remote Control - CA6551 / CA6551SST
The batteries inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries:
1.
Remove 3 screws and disassemble the halves of the remote control.
2.
Remove the old batteries, observing the +/- symbols on the batteries and replace with new batteries.
3.
Reassemble the halves of the remote control and install the 3 screws.
4.
Test operation of the remote control.
NOTE: The CA6551 uses 2 CR2016 batteries and the CA6551SST uses 1 CR2032.
2 Way LCD Remote Control - CA6551
The CR2450 battery inside the 2-way LCD remote control should last approximately 6 months under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the BATTERY icon on the LCD remote control will show.
1.
Gently slide the battery cover off of the remote control.
2.
Remove the old CR2450 battery, observing the +/- symbols on the battery, and replace with a new CR2450 battery.
3.
Gently slide the battery cover on to the back of the remote control.
4.
Test operation of the remote control.
16
2 Way LCD Remote Control - CA6551SST
The battery inside the 2 way LCD remote control is rechargeable, use the supplied battery charger to charge the battery until the battery icon on the
LCD screen shows 3 bars indicating charging is complete. It is recommended that the battery be fully charged before normal use.
2010 Audiovox Electronics Corporation. All rights reserved.
Code Systems, Inc. Limited Lifetime Warranty
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI-
NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts directly related to repairs of the defect(s).
Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for a period of one (1) year from the date of purchase of the Product.
CODE accessories, sold separately, are covered by the applicable warranty accompanying the accessory.
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed from the vehicle in which it was originally installed; or (2) the vehicle in which the Product was originally installed is transferred to another party.
This warranty does not apply to any product damaged by accident, physical or electrical abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts.
In order for the Product to be repaired or replaced under the terms of this warranty, the defective Product must be returned to an authorized CODE dealer and accompanied by a copy of the retail sales receipt. The date of purchase and year, make and model of the vehicle in which the
Product was originally installed must be clearly indicated on the sales receipt.
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED
OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR-
RANTY, EXPRESS OR IMPLIED, WHATSOEVER.
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF
CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE
PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION
LABOR.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state
2010 Audiovox Electronics Corporation. All rights reserved.
17
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
18
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2010 Audiovox Electronics Corporation. All rights reserved.
