Sharp CDSW330H Audio Operation Manual

MODEL

CD-SW300H/CD-SW330H

MINI COMPONENT SYSTEM

This quick Start Guide will help you to correctly install and operate your system.

Illustration printed in this quick guide are for the model CD-SW300H.

1

Accessories

2

Remote control battery installation

Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).

Batteries are not included.

1

Open the battery cover.

2

Insert the batteries as shown.

Remote control × 1 AM loop aerial × 1

3

Close the cover.

FM aerial × 1

3

System connections

FM aerial

Right speaker

AM loop aerial

Left speaker

Purple

Red

Black

Subwoofer

FM

ANTENNA

GND AM

75 OHMS

AC INPUT

Subwoofer light-up wire

Speaker light-up wire

Red

Black Wall socket

(AC 230 V, 50 Hz)

4

Turn on your system

The first time the unit is plugged in, the unit will enter the demonstration mode.

You will see words scroll.

1

Press the X-BASS(SURROUND)/DEMO button to cancel the demonstration mode.

2

Press the ON/STAND-BY button to turn the power on.

TINSEA179AWZZ

07C R KI 1

CD-SW300HE QG 1 3/1/07, 2:50 AM

Listening to a CD or MP3/WMA disc Listening to the radio

1

Press the CD button.

2

Press the 1 button and within 5 seconds, press the button to open the disc tray 1.

3

Place the disc on the disc tray 1, label side up.

12 cm (5”) 8 cm (3”)

4

5

6

Press the button to close the disc tray 1.

You can place discs on trays 2 - 5 by following steps 2 - 4.

Press the / button to start playback.

FM stereo mode indicator

FM stereo receiving indicator

1

Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM).

2

Press the TUNING ( or ) button to tune in to the desired station.

When the TUNING ( or ) button is pressed for more than 0.5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station.

To receive an FM stereo transmission:

Press the TUNER (BAND) button to select stereo mode and “ST” indicator will be displayed.

“ ” will appear when an FM broadcast is in stereo.

Listening to a cassette tape

1

Open the cassette compartment by pushing the area marked “ ”.

2

Load a cassette into the TAPE 1 compartment or TAPE 2 compartment with the side to be played facing towards you.

TAPE 1 TAPE 2

3

Press the TAPE (1 2) button to select the cassette you want to listen to.

4

Press the / (TAPE ) button to start playback.

If trouble occurs

When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction.

If such a problem occurs, do the following:

1.

Set the unit to the stand-by mode and turn the power on again.

2.

If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory by resetting it.

Clearing all the memory (reset)

1.

Press the ON/STAND-BY button to enter the power stand-by mode.

2.

Whilst pressing down the button and the

7 the TUNER (BAND) button until “CLEAR ALL” appears.

Caution:

This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme.

Maintenance

Routine maintenance is required for continued optimum performance, refer to the operation manual.

CD-SW300HE QG 2 3/1/07, 2:50 AM