advertisement
ASSEMBLY
MANUAL
Cuisinart
®
Gourmet 700
85-3056-8 (G52505) Propane
85-3057-6 (G52506) Natural Gas
READ AND SAVE MANUAL FOR FUTURE REFERENCE.
Assemble your grill immediately.
Missing or damaged parts should be claimed within 30 days of purchase.
For product inquiries, parts, warranty and troubleshooting support, please call 1-800-309-3452.
www.cuisinartbbqs.com
LIMITED 5-YEAR WARRANTY
Manual Revision #: 08132013 PD
2
H E A V Y A R T I C L E N E E D S 2 T O L I F T
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at www.cuisinartbbqs.com
CAUTION
Sharp edges. Wear gloves when assembling your grill.
CAUTION
Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook.
DANGER
1. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. Open lid d. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department
2. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.
3. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
INSTALLER OR
ASSEMBLER/CONSUMER
This manual should be kept with the BBQ at all times.
WARNING
Failure to follow all of the Manufacturer’s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death.
Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try lighting this BBQ without reading the Lighting Instructions section of the
Safety and Care Manual that accompanies this grill.
DANGER
1. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
CAUTION
Avoid burns. The stainless steel and steel surfaces of this barbecue can become extremely hot, in direct sun and while the barbecue is in operation.
T H I S B A R B E C U E I S F O R O U T D O O R U S E O N LY
CUISINART
®
CUSTOMER CARE HOTLINE
1-800-309-3452
HARDWARE PACK
Tools Needed for Assembly
• #2 Phillips screwdriver (long and short)
• ¼” Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
• Rubber Mallot
Before assembling the barbecue, read these instructions carefully.
Assemble the barbecue on a flat, clean surface.
Grill is heavy.
Note: Do not fully tighten all the nuts during this initial stage
No. Description
9
10
11
12
13
14
15
16
7
8
5
6
1
2
3
4
1/4-20UNCx38 Screw
1/4-20UNCx18 Screw
1/4-20UNCx13 Screw
1/4" Nut
φ7 Lock Washer
φ7 Washer
φ7 Fiber Washer
NO.10-24UNCx30 Screw
NO.10-24UNCx10 Screw
φ5 Lock Washer
φ5 Washer
M4 Wing Nut
ST4.2X10 Tapping Screw
Control Knob
U Pin
Venturi Clip, Side Burner
Caution:
Sheet metal can cause injury. Wear gloves when installing this grill.
1
1/4-20UNCx38 Screw
X 8
4
1/4” Nut
X 4
7
φ7 Fiber Washer
X 4
10
φ5 Lock Washer
X 2
13
16
ST4.2X10 Tapping Screw
X 8
Venturi Clip, Side Burner
X 1
2
1/4-20UNCx18 Screw
X 4
5
φ7 Lock Washer
X 24
8
11
NO.10-24UNCx30 Screw
X 2
φ5 Washer
X 6
14
Control Knob
X 2
Part Number
20120-13038-250
20120-13018-250
20120-13013-250
30220-13000-250
41400-07000-250
40300-07000-250
G501-0054-9100
20324-10030-250
20124-10010-250
41400-05000-250
40300-05000-250
33301-04000-032
22500-42010-137
G525-0013-9000
G350-0026-9000
G405-0019-9200
Qty.
2
2
6
1
8
2
1
1
24
28
4
2
16
4
8
4
3
1/4-20UNCx13 Screw
X 16
6
φ7 Washer
X 28
9
12
NO.10-24UNCx10 Screw
X 2
M4 Wing Nut
X1
15
U Pin
X 1
1
2
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CE1
CE2
CF1
CF2
CG
CA
CB
CC
CD
BA1
BA2
BB
BC
BD
BE
BF
BG
PARTS LIST (PROPANE) FOR 85-3056-8 (G52505)
Item No.
Qty. Description
AA
AB
AC
AD
AE
AF
1
1
1
Top lid
Lid Handle
Thermometer
2 Screw for Top Lid
2 Lid Bumper
1 Logo Plate
Part No.
G525-2000-01
G525-0033-01
G512-0085-01
G433-0002-01
G508-0063-01
G418-0002-01
Item No.
Qty. Description
DA
DB
DC
DD
DE
DF
DG
DH
DI
DJ
DK
1
1
1
1
1
2
Side Shelf Table - Right
Side Shelf Fascia - Right
Side Burner Drip Pan
1 Side Burner
1 Electrode Set, Side Burner
Lid, Side Burner
Cooking Grate, Side Burner
Towel Bar
1 Side Shelf Table - Left
1 Side Shelf Fascia - Left
1 Multi Spark
TM
Ignition Button
BH
BI
BJ
BK
BL
BM
1 Burner Box Assembly
1 Burner Box Surround
3 Main Burner
G525-3100-01
G525-3200-01
G525-3800-01
1 Carryover Assembly
3 Flame Tamer
3
1
Cooking Grate
Warming Rack
G525-0003-01
G525-0015-01
G525-0016-01
G525-0017-01
G525-3500-01 1 Stainless Steel Rotisserie
Burner
1 Electrode Set, Rotisserie
Burner
G453-0033-01
1 Wind Shield, Rotisserie Burner G501-00B1-01
1 Collector Box, Rotisserie
Burner
G501-00C1-01
1 Match Holder
1 Rotisserie LP Valve
2 Lid Support Pin
G501-0068-01
G525-0009-01
G525-0014-01
F1
F2
F3
F4
EE
EF
EG
EH
EI
EA
EB
EC
ED
1 Left Cart Side Panel
1 Right Cart Side Panel
1 Bottom Shelf - LP
2 Wheel with Lock
2 Wheel
1 Left Door Assembly
1 Right Door Assembly
2 Door Handle
4 Door Magnet Assembly
1 Hardware pack
1 Assembly Manual
1 Safe Use and Care Manual
1 Tank Screw
1 Manifold Assembly, LP
1 Regulator
1 Side Burner Valve, LP
2 Metal Hose
G525-3400-01
G606-0008-01
G525-0008-01
G508-0024-01
1 Rotisserie Flexible Hose
1 Rotisserie LP Orifice
1 Electronic Ignition Assembly
G601-0055-A1
G601-0055-03
G515-0030-03
1 Electronic Ignition Battery Cap G515-0030-01
3 Electrode Set, Main Burner G525-0030-01
5 Control Knob
5 Bezel, Control Knob
1 Control Panel
1 Front Brace
1 Grease Tray
1 Upper Back Panel
1 Heat Shield
1 Left Track
1 Right Track
1 Lower Back Panel
G525-0013-01
G525-0012-01
G525-0010-01
G525-5000-01
G350-4400-01
G525-0021-01
G525-0022-01
G515-0024-01
G515-0025-01
G525-0052-01
Part No.
G525-0600-01
G525-1000-01
G515-0083-01
G453-3400-01
G515-0039-01
G501-0070-01
G501-0077-01
G525-0029-01
G525-0700-01
G525-1100-01
G525-0028-01
G525-0018-01
G525-0019-01
G525-0500-01
G515-0082-01
G350-0024-01
G525-6000-01
G525-7000-01
G525-0025-01
G439-0035-01
G525-B005-01
G525-M005-01
G525-M005-02
G505-0047-01
EXPLODED DIAGRAM (PROPANE)
FOR 85-3056-8 (G52505)
BF
BE
BJ
CE1
BI
BH
BG
CE2
CA
BB
BC
BC
CG
CD
BM
CC
BD
BL
CD
DI
CB
CK
DH
DJ DK
CM
AD
AE
EF
CF2 CF1
EH
EA
CO
EC
CL
CP
BA2
BA1
CJ
BK
DC
EB
EH
ED
CN
AA
AC
AF
AB
CH
CI
DF
DD
DE
DA
DB
DG
DH
EG
EI
EI
EE
CQ
Hardware
Pack
F1
EXTRAS
Assembly
Manual
F2
Safe Use
& Care
Manual
F3
Tank
Screw
F4
3
4
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CE1
CE2
CF1
CF2
CG
CA
CB
CC
CD
BA1
BA2
BB
BC
BD
BE
BF
BG
PARTS LIST (NATURAL GAS) FOR 85-3057-6 (G52506)
Item No.
Qty. Description
AA
AB
AC
AD
AE
AF
1
1
1
Top lid
Lid Handle
Thermometer
2 Screw for Top Lid
2 Lid bumper
1 Logo Plate
Part No.
G525-2000-01
G525-0033-01
G512-0085-01
G433-0002-01
G508-0063-01
G418-0002-01
Item No.
Qty. Description
DA
DB
DC
DD
DE
DF
DG
DH
DI
DJ
DK
1
1
1
1 Side Burner
1 Electrode Set, Side Burner
1
1
Side Shelf Table - Right
Side Shelf Fascia - Right
Side Burner Drip Pan
Lid, Side Burner
Cooking Grate, Side Burner
Part No.
G525-0600-01
G525-1000-01
G515-0083-01
G453-3400-01
G515-0039-01
G501-0070-01
G501-0077-01
2 Towel Bar
1 Side Shelf Table - Left
1 Side Shelf Fascia - Left
G525-0029-01
G525-0700-01
G525-1100-01
1 Multi Spark
TM
Ignition Button G525-0028-01
BH
BI
BJ
BK
BL
BM
1 Burner Box Assembly
1 Burner Box Surround
3 Main Burner
G525-3100-01
G525-3200-01
G525-3800-01
1 Carryover Assembly
3 Flame Tamer
3
1
Cooking Grate
Warming Rack
G525-0003-01
G525-0015-01
G525-0016-01
G525-0017-01
G525-3500-01 1 Stainless Steel Rotisserie
Burner
1 Electrode Set, Rotisserie
Burner
G453-0033-01
1 Wind Shield, Rotisserie Burner G501-00B1-01
1 Collector Box, Rotisserie
Burner
G501-00C1-01
1 Match holder
1 Rotisserie NG Valve
2 Lid Support Pin
G501-0068-01
G525-0036-01
G525-0014-01
EE
EF
EG
EH
EI
EA
EB
EC
ED
F1
F2
F3
1 Left Cart Side Panel
1 Right Cart Side Panel
1 Bottom Shelf - NG
2 Locking Wheel
2 Wheel
1 Left Door Assembly
1 Right Door Assembly
2 Door Handle
4 Door Magnet Assembly
1 Hardware Pack
1 Assembly Manuals
1 Safe Use and Care Manual
G525-0018-01
G525-0019-01
G525-1600-01
G515-0082-01
G350-0024-01
G525-6000-01
G525-7000-01
G525-0025-01
G439-0035-01
G525-B005-01
G525-M005-01
G525-M005-02
1 Manifold Assembly, NG
1 Natural Gas Hose
1 Side Burner Valve, NG
2 Metal Hose
G525-1400-01
G501-0099-01
G525-0035-01
G508-0024-01
1 Rotisserie Flexible Hose
1 Rotisserie NG Orifice
1 Electronic Ignition Assembly
G601-0055-A1
G601-0055-04
G515-0030-03
1 Electronic Ignition Battery Cap G515-0030-01
3 Electrode Set, Main Burner G525-0030-01
5 Control Knob
5 Bezel, Control Knob
1 Control Panel
1 Front Brace
1 Grease Tray
1 Upper Back Panel
1 Heat Shield
1 Left Track
1 Right Track
1 Lower Back Panel
G525-0013-01
G525-0012-01
G525-0010-01
G525-5000-01
G350-4400-01
G525-0021-01
G525-0022-01
G515-0024-01
G515-0025-01
G525-0052-01
EXPLODED DIAGRAM (NATURAL GAS)
FOR 85-3057-6 (G52506)
BF
BE
BJ
CE1
BI
BH
BG
CB
CE2
CA
BB
BC
BC
CG
CD
BM
CC
BD
BL
CD
DI
CK
DH
DJ DK
CM
AD
AE
EF
CF2
CF1
EH
EA
CO
EC
CL
CP
BA2
BA1
CJ
BK
DC
EB
EH
ED
CN
AA
AC
AF
AB
CH
CI
DF
DD
DE
DA
DB
DG
DH
EG
EI
EI
EE
CQ
Hardware
Pack
F1
EXTRAS
Assembly
Manual
F2
Safe Use
& Care
Manual
F3
5
6
ASSEMBLY INSTRUCTIONS
1.
EE
ED
A
Back view
EC
EE
Separate the 2 different types of wheels:
2 Locking Wheels (ED) and 2 Regular Wheels
(EE).
Insert the U Pin (#15) into one of the regular
Wheels (EE), as shown in image B. Attach the
Regular Wheel (EE) to the front of the Bottom
Shelf (EC), and use the U Pin (#15) to secure and tighten.
Repeat for remaining 3 Wheels (EE & ED).
NOTE: Regular Wheels (EE) need to be assembled to the front of the Bottom
Shelf (EC), and Wheels with Lock (ED) need to be assembled to the back of the Bottom Shelf (EC), as shown in image A.
YOU WILL NEED:
15
B
Close up X 1
2.
EB
A) Ensure that the wheels are firmly locked in
the “ON” position before continuing.
B) Assemble the Left Cart Side Panel (EA) and
the Right Cart Side Panel (EB) to the Bottom
Shelf (EC)
EA
EC
YOU WILL NEED:
5 6
A
Front view
X 6 X 6 X 6
EC
EB
B
Close up
ASSEMBLY INSTRUCTIONS
2.
CQ
EB
EA
C
EC
C) Assemble the Lower Back Panel (CQ)
to the Left Cart Side Panel (EA) and Right
Cart Side Panel (EB).
YOU WILL NEED:
5 6
X 4 X 4 X 4
3.
EB
A
Back view
CK
CQ
EA
Attach the Front Brace (CK) to the Left and
Right Cart Side Panels (EA and EB)
TIP: One person should align the left side, while the second person assembles the right side.
YOU WILL NEED:
5 6
X 2 X 2 X 2
CK
EA
B
Close up
7
ASSEMBLY INSTRUCTIONS
4.
A+B
THIS STEP REQUIRES 3 PEOPLE.
DO NOT ATTEMPT ALONE. EXTREMELY
HEAVY.
a. Position the Top Lid and Burner Box
Assembly (A and B) onto Cart Assembly (C), as shown.
A
Front view
C
8
A+B
EB
B
Back view
Close up - left outside view
CK
C
Front view
EA
EB
EA
b. Assemble Burner Box Assembly (A and B) to the Left and Right Cart Side Panels (EA and
EB), as shown.
YOU WILL NEED:
5 6
X 4 X 4 X 4 c. Assemble the front of the Burner Box
Assembly (A and B) to the Front Brace (CK), as shown.
YOU WILL NEED:
5 6
X 2 X 2 X 2
ASSEMBLY INSTRUCTIONS
5.
CM
EB
A
Back view
EA
CM
B
Close up
EA
Attach the Upper Back Panel (CM) to both the
Left and Right Cart Side Panels (EA and EB).
Only install hardware in the bottom portion of the Upper Back Panel (CM), as shown in figure
B.
DO NOT TIGHTEN SCREWS UNTIL SIDE
SHELF HAS BEEN INSTALLED
YOU WILL NEED:
5 6
X 2 X 2 X 2
9
10
ASSEMBLY INSTRUCTIONS
6.
DI
BA
a. Open the Lid. Assemble the Left Side Shelf
Assembly (DI and DJ) to the Cart Assembly by inserting the Side Shelf tabs into holes on the Cart Assembly (figure A).
A
DJ
Front, left side view
B2
DI
B
Front, left side view
B2
A1
BA
A1
DI
BA
b. Secure using hardware, as shown in figure
B, C & D.
YOU WILL NEED:
7 6 4
DJ
X 2
A1
X 2
YOU WILL NEED:
5
X 1 X 1
6
X 1
X 2
B2
X 2
C
View under left side shelf
DI
YOU WILL NEED:
11
X 2 X 2
BA
D
View under left side shelf
DJ
ASSEMBLY INSTRUCTIONS
7.
BL
DI
DJ
A
Front, left side view
8.
DI
DJ
BL
B
Front, left side view
CJ
DH
14
a. Remove the hardware that is pre-assembled to the Rotisserie Valve (BL), as shown in figure A. b. Insert the Rotisserie Burner Valve Stem (BL) through the rear of the Left Side Shelf Fascia
(DJ). Assemble the Rotisserie Valve (BL) to the Side Shelf Fascia (DJ), using the hardware removed. c. Assemble the Side Burner Control Knob
(#14) to the Rotisserie Valve (BL).
YOU WILL NEED:
X 1 a. Assemble the Towel Bar (DH) to the Control
Panel (CJ) and Left Side Shelf (DI), as shown in figure A & B.
A
B
DI
CJ
DI
DH
YOU WILL NEED:
5 6
X 1 X 1 X 1
DJ
11
ASSEMBLY INSTRUCTIONS
8.
DJ
9.
C
View under Left Side Shelf
DK
BA
DA
A
Front, right side view
DB
b. Attach the two ignition button wires to the
Electronic Ignition Button (DK), as shown in figure C.
a. Open the lid. Assemble the Right Side Shelf
Assembly (DA and DB) to the Cart Assembly by inserting the Side Shelf tabs into the holes on the Cart Assembly (figure A).
12
Close up
A1
BA
A1
B
View inside burner box
B2
DA
B2
b. Secure using hardware, as shown in figure B,
C & D.
YOU WILL NEED:
7 6 4
X 2
A1
X 2 X 2
B2
X 2
ASSEMBLY INSTRUCTIONS
9.
DA
DB
C
View under right side shelf
DA
BA
YOU WILL NEED:
5
X 1 X 1
6
X 1
YOU WILL NEED:
11
X 2 X 2
BA
10.
D
DB
View under right side shelf
CC
A
Front, right side view
DA
DB
a. Remove the hardware that is pre-assembled to the Side Burner Valve bracket (CC), as shown in figure A. b. Insert the Side Burner Valve stem (CC) through the rear of the Right Side Shelf
Fascia (DB). Assemble the Side Burner Valve
(CC) to the Side Shelf Fascia (DB), using the hardware removed (figure A).
DA
DB
c. Assemble the Side Burner Control Knob
(#14) to the Side Burner Valve (CC) (figure B).
YOU WILL NEED:
B
Front, right side view
CC
14
X 1
13
14
ASSEMBLY INSTRUCTIONS
11.
DA
DH
CJ
A
Front, right side view
DB
DH
Assemble the Towel Bar (DH) to the Control
Panel (CJ) and Right Side Shelf (DJ), as shown in figure A & B.
DA
YOU WILL NEED:
5 6
X 1 X 1 X 1
12.
DB
B
Right side view a. Position the Side Burner (DD) through the opening in the Side Burner Drip Pan (DC).
DD
DC
A
Front, right side view
NOTE: Make sure that the Side Burner (DD) engages the Side Burner Valve (CC), as shown in figure B.
CC
B
View under Right Side Shelf
DD
ASSEMBLY INSTRUCTIONS
12.
DC
12
b. Use the Wing Nut (#12) to assemble the
Side Burner (DD) to the Side Burner Drip Pan
(DC), as shown in figure C.
YOU WILL NEED:
C
DD
View under right side shelf
CC
16
DD
X 1 c. Use the Side Burner Venturi Clip (#16), connect the Side Burner (DD) to the Side
Burner Valve (CC).
YOU WILL NEED:
X 1
D
View under right side shelf
DC
d. Attach the end of the Side Burner Electrode
Wire (DE) to the underside of the Side Burner
(DD), as shown in figure E. Ensure that the wire is pushed in firmly.
DE
E
View under right side shelf
DD
e. Place the Side Burner Cooking Grate (DG) into position on the Side Shelf (DA), as shown in figure F.
DA
DG
F
Front, right side view
15
16
ASSEMBLY INSTRUCTIONS
13.
A
CF2
EA
CF1
a. Remove the Electronic Ignition Battery Cap
(CF2) and the plastic nut from the Electronic
Ignition Assembly (CF1).
b. Feed the Electronic Ignition Assembly (CF1) through the opening in the Left Side Panel
(EA) and secure using the nut. c. Insert one “AA” battery into the battery compartment with the positive end facing outward, as shown. Secure using the
Electronic Ignition Battery Cap (CF2).
B
CF2
+
-
TIP: The Electrode set, Main Burner (CG), the Electrode Wire, Side Burner (DE), and the Electrode Wire, Rotisserie Burner (BH) can be found attached to the control panel heat shield (CJ), as shown.
CJ
C
CG
D
CF1
d. Insert the three Electrode set, Main Burner wires (CG) into the Electronic Ignition
Assembly (CF1), as shown in figure D.
NOTE: All main burner, side burner and rotisserie burner electrode wire connection points are the same size.
ASSEMBLY INSTRUCTIONS
13.
CG
CF1
DE
BH
E
e. Insert the Electrode wire, Side Burner (DE) and the Electrode wire, Rotisserie Burner
(BH) into the Electronic Ignition Assembly
(CF1), as shown in figure E.
DK
f. Insert the two Electronic Ignition Button
Wires (DK) into the Electronic Ignition
Assembly (CF1), as shown in figure F.
CG
CF1
DK
DE
BH
F
14.
a. Position the Heat Shield (CN) into the two hooks located on the bottom of the Upper
Back Panel (CM), as shown in figure A.
CM
CN
Back view
CN
CM
Close up
17
18
ASSEMBLY INSTRUCTIONS
14.
CK
CN
Front view
CK
Close up
CN
15.
CK
EA
CO
CP
A
Front, right side view
EB
b. Assemble the Heat Shield (CN) to the bottom of the Front Brace (CK), as shown in figure B.
YOU WILL NEED:
X 2 a. Assemble the Left and Right Tracks (CO and CP) for the Grease Tray (CL), as shown in figure A-C.
b. Both the Left and Right Tracks (CO and CP) should be inserted into the two clips located on the Upper Back Panel (CM), as shown in figure B.
CO
CM
B
Close up, back
CP
ASSEMBLY INSTRUCTIONS
15.
CK
CO CP
C
Close up, front c. Assemble the front of the Left and Right
Tracks (CO and CP) to the Front Brace (CK), as shown in figure C.
YOU WILL NEED:
X 2 d. Insert the Grease Tray (CL) into the opening of the Upper Back Panel (CM).
CL
D
16.
A1
B2
CM
EG
EH
Assemble the Door Handle (EH) to the Left and
Right Door Assembly (EF and EG) as shown in figure A.
YOU WILL NEED:
10 11
X 2 X 2
A1
X 2
X 2
B2
19
20
ASSEMBLY INSTRUCTIONS
17.
a. Assemble the Right Door Assembly (EG), to the Bottom Shelf (EC) by inserting the fixed pin (bottom of door) into the hole provided
(figure B).
EG
A
EC
C
CK
B
EC
EG
EG
b. Assemble the top of the Door Assembly (EG) to the Front Brace (CK), by pressing in the door support pin and aligning with the hole located on the top right corner of the door.
TIP: Use a paint scraper to press-in the support pin, while the second person aligns the door. The support pin will lock into position when the door is assembled correctly. c. Repeat steps b, and c for the Left Door
Assembly (EC).
ASSEMBLY INSTRUCTIONS
18.
BD
Place the Flame Tamers (BD) into the Burner
Box (BA).
19.
BE
a. Place the Cooking Grates (BE) into the
Burner Box (BA), as shown.
BF
BA
b. Assemble the Warming Rack (BF) by inserting the fixed pins into the warming rack support bars located on the Burner Box (BA), as shown.
21
22
ASSEMBLY INSTRUCTIONS
20.
CB
A
B
EC
F4
EC
FOR PROPANE MODELS ONLY.
For natural gas model, follow step 21.
a. Position the Regulator Hose (CB) through the hole in the Right Side Panel (EB).
b. Position the 20 lb propane tank onto the
Bottom Shelf (EC), and secure using the
Bolt (F4) (already attached) located on the underside of the Bottom Shelf, as shown in figure B. c. Attach the regulator coupling nut to the LP cylinder valve. Be careful not to cross thread.
Hand tighten only.
d. Perform Leak Test. See page 5 of the
Cuisinart
®
Safety and Care Manual.
ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the
Cuisinart
®
Safety & Care Manual.
All Safety and Leak Test MUST BE
PERFORMED BY THE END USER, prior to lighting this BBQ.
WARNING Do not store extra propane tanks within BBQ cart.
ASSEMBLY INSTRUCTIONS
21.
CC
CB
FOR NATURAL GAS MODEL ONLY.
a. Attach the Natural Gas Hose (CB) to the Side
Burner Valve (CC) as shown. b. Perform Leak Test. See page 6 of the
Cuisinart
®
Safety and Care Manual.
ATTENTION: In order to complete installation of your Natural Gas BBQ a 1/2” or 3/8” adapter may be required to connect your BBQ’s Natural Gas hose to your home gas supply.
Contact your Natural Gas supplier to purchase the necessary part.
ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the
Cuisinart
®
Safety & Care Manual.
All Safety and Leak Test MUST BE
PERFORMED BY THE END USER, prior to lighting this BBQ.
Visit www.cuisinartbbqs.com to complete product registration.
Cuisinart
®
Gourmet Barbecues Customer Service:
1-800-309-3452
Join the conversation
facebook.com/cuisinartbbqs twitter.com/cuisinartbbqs
Cuisinart
®
is a registered trademark used under license
© 2014 Trileaf Distributions Trifeuil
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement