NOTE: This manual is only a supplement. Refer to installation/operation manual for full instructions.

Automatic

Washers

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

W001C

W001C www.comlaundry.com

Part No. 201071

October 2002

Installation/Operation Supplement

WARNING

For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

W022E

IMPORTANT: Read the complete INSTALLATION/OPERATION INSTRUCTIONS before using the washer.

201071 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 1

Installation/Operation Supplement

Notes

2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Table of

Contents

Installation/Operation Supplement

Important Safety Instructions ...........................................................

5

Installation...........................................................................................

7

Dimensions and Specifications.............................................................

7

Installing the Washer ............................................................................

8

Step 1: Remove the Shipping Brace and Shipping Plug..................

8

Step 2: Wipe Out Inside of Washtub ...............................................

8

Step 3: Connect Water Inlet Hoses ..................................................

8

Step 4: Connect Drain Hose to Drain Receptacle ............................

9

Step 5: Position and Level the Washer ............................................ 11

Step 6: Plug In the Washer............................................................... 11

Step 7: Add Water to the Washer .................................................... 11

Step 8: Check Lid Switch ................................................................ 11

Step 9: Check Installation ................................................................ 11

Electrical Requirements........................................................................ 12

Earthing Instructions ........................................................................ 12

Water Supply Requirements ................................................................. 13

Operation............................................................................................. 15

Operation Instructions .......................................................................... 15

Step 1: Add Detergent...................................................................... 15

Step 2: Load Laundry....................................................................... 15

Step 3: Close Lid.............................................................................. 15

Step 4: Set Water Level Selector ..................................................... 15

Step 5: Set Wash/Rinse Temperature Selector ................................ 15

Step 6: Set Timer to Proper Setting ................................................. 16

Step 7: Start Washer......................................................................... 16

Maintenance ........................................................................................ 17

Reinstallation of Shipping Materials ............................................... 17

© Copyright 2002, Alliance Laundry Systems LLC

All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.

201071 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3

Installation/Operation Supplement

Notes

4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Installation/Operation Supplement

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

1. Read all instructions before using the washer.

2. Refer to the EARTHING INSTRUCTIONS in the INSTALLATION manual for the proper earthing of the washer.

3. Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

5. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS

IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. THE

GAS IS FLAMMABLE, DO NOT SMOKE OR

USE AN OPEN FLAME DURING THIS TIME.

6. Do not allow children to play on or in the washer.

Close supervision of children is necessary when the washer is used near children. This is a safety rule for all appliances.

7. Before the washer is removed from service or discarded, remove the lid to the washing compartment.

8. Do not reach into the washer if the washtub or agitator is moving.

9. Do not install or store the washer where it will be exposed to water and/or weather.

(Save These Instructions)

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

12. To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to connect the washer to the electrical power source.

13. Use your washer only for its intended purpose, washing clothes.

14. ALWAYS disconnect the washer from electrical supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.

15. Install the washer according to the

INSTALLATION INSTRUCTIONS. All connections for water, drain, electrical power and earthing must comply with local codes and be made by licensed personnel when required. Do not do it yourself unless you know how!

16. To reduce the risk of fire, clothes which have traces of any flammable substances such as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc. or chemicals such as in mops and cleaning cloths, must not be put into the washer. These flammable substances may cause the fabric to catch on fire by itself.

17. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

18. Keep your washer in good condition. Bumping or dropping the washer can damage safety features.

If this occurs, have your washer checked by a qualified serviceman.

19. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

20. Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 201071

Installation/Operation Supplement

21. Loading door MUST BE CLOSED any time the washer is to agitate or spin. DO NOT bypass the loading door switch by permitting the washer to agitate or spin with the loading door open. A brake will stop the washtub within seconds if the loading door is opened during spinning. If the washtub does not stop when the loading door is opened, remove the washer from use and call the service person.

22. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times

(preferably in a locked cabinet).

23. Always follow the fabric care instructions supplied by the garment manufacturer.

24. Never operate the washer with any guards and/or panels removed.

25. DO NOT operate the washer with missing or broken parts.

26. DO NOT bypass any safety devices.

27. Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNING and IMPORTANT

SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand.

6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Installation

Dimensions and Specifications

711 mm (28 in.)

Installation/Operation Supplement

650 mm (25.6 in.)

*With leveling legs turned into base.

10.2 mm (0.4 in.)

660 mm (26 in.)

TLW1030N

TLW1030N

201071 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7

Installation/Operation Supplement

Installing the Washer

NOTE: This manual is only a supplement. Refer to installation/operation manual for full instructions.

Step 1: Remove the Shipping Brace and

Shipping Plug

IMPORTANT: The shipping brace and plug should be saved and must be reinstalled whenever washer is moved or transported to a new location.

1

Step 3: Connect Water Inlet Hoses

Hoses Without Metric Coupling

Insert rubber washers in water inlet hose couplings.

Connect inlet hoses to water supply faucets. Turn on the water supply faucets and flush the lines. Connect hoses to the hot and cold valve connections at rear of washer.

Hoses With Metric Coupling

Connect the BLACK colored hose coupling end of the inlet hoses (with filter washers) to the water supply faucets. Connect the BRASS colored hose coupling end of hoses (with rubber washers) to the hot and cold water mixing valve connection at rear of washer.

IMPORTANT: DO NOT cross thread or overtighten couplings.

1

2

WATER

MIXING

VALVE

8

2

1

2

Shipping Brace

Shipping Plug

Figure 1

Step 2: Wipe Out Inside of Washtub

TLW521N

1

2

3

3

Water Inlet Hoses

Cold Water Connection

Hot Water Connection

Figure 3

1

2

TLW872N

1

W091I

1

2

Rubber Washer (Plain)

Inlet Hose

Figure 4

W371I

Figure 2

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Step 4: Connect Drain Hose to Drain

Receptacle

Installation/Operation Supplement

High Standpipe Installation

2

1

3

2

1

TLW873N

1

2

Retainer Clamp

Standpipe Adapter

Figure 5

IMPORTANT: Drain receptacle must be capable of handling a minimum of 3.2 cm (1-1/4 inch) outside diameter drain hose.

Standpipe Installation

1 2

30.48 cm

(12 in.)

91.44 cm (36 in.)

RECOMMENDED

HEIGHT

4

3

4

1

2

TLW875N

TLW875N

Standpipe Adapter

Drain Hose

Tie-Down Strap

Standpipe (Standpipes higher than 122 cm

[4 ft.] are not recommended)

Figure 7

Low Standpipe Installation

NOTE: No. 562P3 Siphon Break Kit is required for this type of installation (available at extra cost).

1

2

201071

3

4

1

2

4 3

TLW874N

Ribbed Portion of Drain Hose

Standpipe Adapter

Tie-Down Strap

Standpipe 5.08 cm (2 in.) or 4 cm (1-1/2 in.)

Diameter

Figure 6

3

1

2

3

562P3 Siphon Break Kit

Drain Hose

Standpipe

Figure 8

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

TLW876N

9

Installation/Operation Supplement

Sink Installation

2

1

3

Laundry Tub Installation

1

2

3

Drain Hose

Tie-Down Strap or Wire Tie

Cabinet Top Hinge

Figure 9

In-the-Wall Installation

1

TLW877N

1

1 Tie-Down Strap (Tape if necessary)

TLW878N

TLW878N

Figure 11

10

1

2

2

W514I

Tie-Down Strap (Tape if necessary)

Standpipe Adapter

W514I

Figure 10

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Step 5: Position and Level the Washer

Installation/Operation Supplement

Step 7: Add Water to the Washer

3

2

1

5

3

4

1

2

5

Rubber Foot

Washer Base

Level

Locknut

Leveling Leg

Figure 12

Step 6: Plug In the Washer

4

W179I

W179I

Figure 14

Step 8: Check Lid Switch

W391I

W391I

W376IE0C

Figure 15

Step 9: Check Installation

Figure 13

W422I

W422I

201071 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11

Installation/Operation Supplement

Electrical Requirements

230 Volt/50 Hertz

NOTE: This manual is only a supplement. Refer to installation/operation manual for full instructions.

WARNING

To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST abide with local electrical codes. It is the customer’s responsibility to have the wiring and fuses checked by a qualified electrician to make sure the laundry room has adequate electrical power to operate the washer.

W244

WARNING

To reduce the risk of electric shock or fire,

DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

W031

The washer is designed to be operated on a separate polarized three-wire, earthed 230 Volt, 50 Hertz, single-phase electrical circuit and must abide by local electrical codes.

Earthing Instructions

The washer must be earthed. In the event of malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. The washer is equipped with a cord having an equipment-earthing conductor and a threeprong earthing plug. The plug must be plugged into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinances.

WARNING

Improper connection of the equipmentearthing conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly earthed.

W032

Do not modify the plug provided with the washer – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WARNING

Any disassembly requiring the use of tools must be performed by a suitably qualified service person.

W299

NOTE: Electrical receptacle must be located so that it is easily accessible with machine in place. If machine is hard wired, an intermediate shut-off box with a 3 mm gap is required (335-1 [22.2]

[24.3]).

12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Installation/Operation Supplement

Water Supply Requirements

NOTE: This manual is only a supplement. Refer to installation/operation manual for full instructions.

WARNING

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not smoke or use an open flame during this time.

W029

1

2

C

H

WATER

MIXING

VALVE

3

4

1

2

4

Water Supply Faucets

Cold Water Connection

Hot Water Connection

Water Inlet Hoses

3

TLW879N

Figure 16

Washer needs two standard 19.1 mm (3/4 inch) water supply faucets with a pressure between 1.4 and 8.3 bar

(20-120 pounds per square inch).

201071 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13

Installation/Operation Supplement

Notes

14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Installation/Operation Supplement

Operation

Step 3: Close Lid

Operation Instructions

NOTE: This manual is only a supplement. Refer to installation/operation manual for full instructions.

Step 1: Add Detergent

Figure 19

Step 4: Set Water Level Selector

W318IE0C

CPW69

LOWEST WATER FILL

CPW70

HIGHEST WATER FILL

W395I

Figure 17

Step 2: Load Laundry

Load dry clothes loosely into washtub – DO NOT overload! (7 kg maximum dry clothes load.)

CPW189

CPW189

Figure 20

Step 5: Set Wash/Rinse Temperature

Selector

HOT WASH/

COLD RINSE

CPW71

Figure 18

W392I

CPW72

CPW73

WARM WASH/

COLD RINSE

COLD WASH/

COLD RINSE

CPW173

CPW173

Figure 21

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 15 201071

Installation/Operation Supplement

Step 6: Set Timer to Proper Setting Step 7: Start Washer

Pull the timer knob to start water fill. Agitation will begin when the water level reaches the level selected.

16

PULL KNOB TO START – PUSH TO STOP

CPW82

Figure 24

Figure 22

REGULAR CYCLE

CPW88

CPW60

PERMANENT PRESS

CYCLE

CPW74

DELICATE CYCLE

CPW62

WASH

CPW63

RINSE

CPW64

CPW65

SPIN

END OF CYCLE (OFF)

Figure 23

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201071

Installation/Operation Supplement

Maintenance

NOTE: This manual is only a supplement. Refer to installation/operation manual for full instructions.

Reinstallation of Shipping Materials

Shipping Brace

Open the washer lid and place the brace over the washer agitator, placing the back of the brace into the lid opening first.

Shipping Plug

The plug fits into two openings: the base opening and the shipping plug opening on the bottom of the movable pivot dome. The plug MUST be inserted into both openings to prevent damage to the washer. Refer to Figure 25.

1

2

3

Shipping Plug Opening

Base Opening

Shipping Plug

Figure 25

2

3

1

W544I

201071 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17