advertisement
ACM-3401 Series
Megapixel IP PoE Dome
Hardware User’s Manual
(DC 12V / PoE)
Ver. 2010/6/4
ACM-3401 Series Hardware User’s Manual
Table of Contents
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Installation Procedure .................................................................. 11
Ceiling Mount ............................................................................... 11
Wall Mount ................................................................................... 14
Basic Connections ......................................................................... 17
Product Specification .................................................................... 18
If you have DHCP server / router in your network: ...................... 19
If you do NOT have DHCP server / router in your network: ......... 19
ACM-3401 Series Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local office if you find any inaccuracies or omissions. We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the interference at their own expense.
ACM-3401 Series Hardware User’s Manual
1. Introduction
Package Contents
ACM-3401 Power Adaptor (Optional)
Product CD Accessories
Warranty Card Drill Template
Drill template
ACM-3401 Series Hardware User’s Manual
Features and Benefits
This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality (8 FPS @ SXGA, 1280x1024) through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system.
MPEG-4/MJPEG Dual Codec Compression
This device supports two compression formats, MPEG-4 and MJPEG. It brings superior image quality at 8 frames per second up to a resolution of SXGA (1280 x 1024) pixels, and offers up to
10 frames per second in HD720 (1280x720). In VGA (640 x 480) / QVGA / QQVGA the device reaches 30 frames per second.
Built-in Hardware Motion Detection
No more external motion sensors are required. You may assign up to 3 video motion detection areas. By tuning the object size and sensitivity, it will reliably detect objects passing though in view.
Hardware motion detection also offers better sensitivity and faster response time than software motion detection.
Powerful Bundled Surveillance Software
To extend the capabilities of the IP Camera series, a powerful surveillance program is included in the package for free. Users can easily use an existing PC as a digital video recorder. Scheduled recording and manual recording keep every important video recorded in the local hard disk.
Reliable and accurate motion detection with instant warning enables immediate response in every condition. Quick and simple search and playback function lets you easily find the images and video you want.
Software Development Kit Support
This IP Camera can be integrated or controlled by applications from third party software developers. Software developers can save considerable efforts by using our Streaming Library or
ActiveX control. Please contact us for details on integration support.
Digital Time Code Embedded
The “Digital Time Code Embedded” function records video time in the video stream. Therefore, each image frame is marked with its original recording time. It is very useful when users want to find the video at an exact time or between a certain time intervals.
ACM-3401 Series Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above.
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this manual. Adjust only those controls that are covered by the instruction manual, as an improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the video product to its normal operation.
ACM-3401 Series Hardware User’s Manual
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition.
ACM-3401 Series Hardware User’s Manual
Physical description
1) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
2) Power Input
Connect the power adaptor here if your power input is DC12V.
PIN NAME DESCRIPTION
1 12V DC Power Input
2 GND Ground Pin
3) Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
ACM-3401 Series Hardware User’s Manual
Step 3: Reconnect the power cable while continuing to hold the reset button.
The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for another second and turn off again. By this time the reset to default operation is already completed. This will take around 20 seconds from power up. You may then release the reset button. This length of time fluctuates slightly with the environment. The Power LED light will come back on and stay on after a few more seconds. The unit will start up with factory default settings automatically.
Power On
Restore to Default
Complete
On (3s) Off (about 15s)
On
1s
Off (10~15s) Stay On
About 20 Seconds
4) Digital Input / Output *
The IP device supports Digital Input / Output with terminal block connections. Pushing down the tab above will reveal a small slot for you to insert the end of wire. Release the tab and the wire will be fastened by the internal spring. The connection pins are as shown in this image:
Digital Input / Output include the following:
•1 transistor output - For connecting external devices such as relays and LEDs. Connected devices can be activated by Output buttons on the Live View page or through video management software.
•1 Digital Input - An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The device will detect the change in digital input and transmit the signal to video surveillance servers.
ACM-3401 Series Hardware User’s Manual
Terminal Pin Define is described as below:
Pin Name
DIO PW
DIO GND
DO
(Transistor
Output)
DI
(Digital
Input)
Description
Electrically connected in parallel with the connector for the power supply, this pin provides an auxiliary connector for mains power to the unit.
This pin can also be used to power auxiliary equipment, with a maximum current of 100mA.
Ground
Uses an open-collector NPN transistor with the emitter connected to the GND pin. If used with an external relay, a diode must be connected in parallel with the load, for protection against transient voltages.
Connect to GND to activate, or leave floating (or unconnected) to deactivate.
Spec
Voltage: 12V DC,
Max: 1.2W
Description
Max load = <100mA
Max voltage = 24V
DC (to the transistor)
Must not be exposed to voltages greater than 30V DC.
* Available only for device versions with enhancements
5) Audio Input / Output
The IP device supports Audio input / output with terminal block connections. Pushing down the tab above will reveal a small slot for you to insert the end of wire. Release the tab and the wire will be fastened by the internal spring. The connection pins are as shown in this image:
ACM-3401 Series Hardware User’s Manual
Installation Procedure
Ceiling Mount
Use the drill template, and drill a hole with φ 35 on the ceiling
Tighten the plate to ceiling with M4*20 screws
ACM-3401 Series Hardware User’s Manual
Connect cables through the hole on the ceiling and plate, or on the side of casing
Fasten the camera to ceiling by turning clockwise direction
ACM-3401 Series Hardware User’s Manual
Insert the cables (Power/Network/DIO/Audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable.
1.6.1.6 Done
ACM-3401 Series Hardware User’s Manual
Wall Mount
Tighten wall mount bracket to the wall by 3 PAN Head Tapping screws
3-PAN HEAD SCREW TAPPING
Tighten the plate to wall mount bracket with M4*10 screws, and connect all necessary cables through the hole on the plate and wall mount kit
2-FLAT HEAD SCREW TAPPING(M4x10
)
ACM-3401 Series Hardware User’s Manual
Note: that there ’s a triangle mark on both plate and wall mount kit. Those triangle marks need to be fixed to the same direction.
Insert the cables (power/Network/audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable.
ACM-3401 Series Hardware User’s Manual
Fasten the camera to wall mount kit by turning clockwise direction
Done
ACM-3401 Series Hardware User’s Manual
Basic Connections
Follow the procedures below to connect the IP device to the respective apparatuses.
If you have a PoE(Power over Ethernet) supported switch or injector:
1) Connect your IP Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45 connector.
2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
If your switch does not support PoE, and you are powering the camera with power adaptor:
1) Connect the power adaptor to IP Camera
2) Connect IP device ’s Ethernet port to Network switch (via RJ45 connectors).
3) Connect a PC to the Ethernet switch (via RJ45 connectors)
Please refer our PoE Guide for more details on Power over Ethernet related concepts.
ACM-3401 Series Hardware User’s Manual
Product Specification
Image
Min. Scene
Illumination
Lens
Camera Angle
Adjustment
Synchronization
Day/Night Functions
Functions
Audio Input
Audio Output
Device
Size
Effective Pixels
Color
B/W
IR Sensitivity
CDS Sensor
Focal Length
Viewing Angle
X (Panning)
Y (Tilting)
Sync. System
Mechanical IR Cut
Filter
Motion Detection
Electronic Shutter
Fixed Shutter (Manual)
Flickerless
AGC
ACM-3401 ACM-3411
Micron Progressive Scan CMOS
1/3 inch
N/A
1280(H) x 1024(V)
0.5 Lux at F1.0 (2400 ºK, 30 IRE)
Color mode automatically switched to B/W mode under 4 Lux
0.05 Lux at F1.0 (2400 ºK, 30 IRE)
N/A
N/A f4.2 mm / F1.8
63.7º (Horizontal)
0º ~170º
0º ~90º
Internal
From 700nm to 1100nm
Yes
N/A Yes
Yes (3 Windows)
1/5 ~ 1/15,000 sec
1/30 ~ 1/1,000 sec. (60Hz); 1/25 ~ 1/1,000 sec. (50Hz)
1/120 sec. (60Hz); 1/100 sec. (50Hz)
Automatic (User defined)
S/N Ratio
Video Compression
External I/O
Alarm
Casing
White Balance
S/N Ratio
Compression
Picture Resolution
Bit Rate
Image Frame Rate
Compression
Audio Line Input
Compression
Audio Line Output
Reset Button
Digital Input
Digital Output
Mount Types
Ethernet Port
AUTO, INDOOR1, INDOOR2, OUTDOOR1, OUTDOOR2, HOLD CURRENT,
MANUAL
Better than 44 dB
MPEG-4 SP, MJPEG selectable
SXGA (1280x1024); HD720 (1280x720); VGA (640x480); QVGA(320x240);
QQVGA(160x112)
28K ~ 3M bps
8 fps at SXGA; 10fps at HD720; 30 fps at VGA; 30fps at QVGA; 30fps at
QQVGA
8kHz, Mono, PCM
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
8kHz, Mono, PCM
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
Factory default
1, TTL, terminal block *
1, TTL, terminal block *
Surface / Pendant* / Wall* / Corner* / Pole* / Flush*
Ethernet (10/100 Base-T), RJ-45 connector
Network
Protocol
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, DNS, DDNS, NTP,
ICMP, ARP, IGMP, SMTP, FTP, UPnP
Software
Web Browser
SDK
Operating
Power
Security
Temperature
Power Requirement
Power Consumption
Dimensions (Ø xH)
Physical
Weight
Approvals Certificate
* Available only for device versions with enhancements
Microsoft Internet Explorer 6.0 or above
ACTi SDK-10000
Password protection: configured by the administrator
-10 ºC ~ 50 ºC (14 ºF ~ 122 ºF)
PoE (IEEE802.3af) with Class 3
3.3 W (DC 12V); 4.3 W (PoE)
130 mm x 99 mm (5.12” x 3.90”)
350 g (0.7 lb)
CE, FCC
ACM-3401 Series Hardware User’s Manual
2. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do network:
NOT
have DHCP server / router in your
1. Configure your PC to use the same subnet by changing your PC’s IP address to the subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254 except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255.0
(NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network.)
ACM-3401 Series Hardware User’s Manual
6. After logging in, you will see the video from camera. To go to the main menu, click the ”Setup” button on the top left.
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin Password: 123456
ACM-3401 Series Hardware User’s Manual
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another unused
IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps.
7. Go to Setup -> WAN Setting
8. Choose Static IP Address.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC ’s IP address or 192.168.0.100.). If this is not the first device you add to the network, please also avoid other devices ’ IPs.
10. Click “Apply”
11. Please go to Save Reboot, and click ”Apply”. Internet Explorer will close after a few seconds. This is normal.
ACM-3401 Series Hardware User’s Manual
12. Wait for 30 seconds, and open IE again to connect to the new IP . (In this example,
192.168.0.101). For the second device or more you add into the network, please type the correct IP.
13. Adjust the video stream by going to Video Setting
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement