User's manual | ENDAT 4066i User`s manual

User’s Manual I

ENDAT-4066i

User’s Manual

Rev. 1A

4066i PCB ver: A2 or later

25/05/2007

II The ENDAT-4066i System Board

Copyright Notice

The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to this document and/or the product at any time without prior

notice. No part of this document may be reproduced, transmitted, photocopied or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical or chemical, without the prior written permission of the manufacturer.

Intel® Pentium4®, Celeron® and Celeron D ® is registered trademark of Intel

Incorporation

Multiscan is a trademark of Sony Corp of America

IBM, EGA, VGA, PC/XT, PC/AT, OS/2 and PS/2 are registered trademarks of

International Business Machines Corporation

Plug and Play is registered trademarks of Intel Corporation

Microsoft, Windows and MS-DOS are trademarks of Microsoft Corporation

Award is a trademark of Phoenix Software Inc.

PCI is a registered trademark of PCI Special Interest Group

Other product names mentioned herein are used for identification purpose only and may be trademarks and/or registered trademarks of their respective companies.

Installation Notice

The manufacturer recommends using a grounded plug to ensure proper motherboard operation. Care should be used in proper conjunction with a grounded power receptacle to avoid possible electrical shock. All integrated circuits on this motherboard are sensitive to static electricity. To avoid damaging components from electrostatic discharge, please do not remove the board from the anti-static packing before discharging any static electricity to your body, by wearing a wrist-grounding strap. The manufacturer is not responsible for any damage to the motherboard due to improper operation.

User’s Manual III

Specification:

Model ENDAT-4066i

Form Factor

System Chipset

Mini-ITX 170 mm x 170 mm (6.69”x6.69”)

INTEL 865GV + ICH5

CPU Supporting 533/400 FSB with 478 pin PENTIUM4/Celeron/Celeron D processor

Memory

Ethernet

VGA

LCD interface

1 x 184 pin DDR socket support DDR 400/333/266 up to 1GB

INTEL 82801ER/EB (ICH5) + PHY (Intel 82562EX)

INTEL 865GV Graphic Controller with DVMT up to 96MB(max)

Onboard LVDS support 18/24/36/48bit Single/Dual Channels via internal box header (optional)

Display ratio 4:3 and 16:9

Serial / Parallel

2 Serial Port w/+5V, +12V Power Selector / 1 Parallel port ( Optional to 6

Serial ports via I/O kit)

Watchdog Timer Winbond 83627THG on-chip support 1 to 255 seconds/minutes

IDE Connector

1 x 40pin IDE connector support UDMA 33/66/100

1 x 44pin IDE connector support Slim type HDD

SATA Connector

AUDIO

I/O Port

Support 1 port 150MHz Serial ATA Device

On-board support AC'97 with 1.2W amplifier

CMOS backup EEPROM backup customized setting in system BIOS

Expansion Slot One PCI expansion up to 3 PCI slots via riser card with PCI 2.2 compliance

PS/2 Keyboard / Mouse Connector

2 x USB (2.0) + RJ-45 Connector w/LED indicator

D-sub Connector for COM 1,2 (internal box header for COM2) with

POWER

1 x 25 Pins D-Sub Connector (LPT)

1 D-Sub Connector (VGA)

MIC-IN, Line-In, SPK-Out with COM2 Module Deck

Internal pin header: KB, MS, USB (2.0) x4, AUX/CD-IN, SPDIF IN/OUT, RF

MIC IN, IR

Digital IO

RS-422/485

USB Port

Power Supply

2 bit input and 2 bit output (TTL level) by pin header

Via COM2 (Optional)

6 x USB2.0 onboard

Support P4-ATX power supply

IV The ENDAT-4066i System Board

TABLE OF CONTENTS

CHAPTER 1. INTRODUCTION ....................................................... 1

1-1. FEATURES .............................................................................................. 2

1-2. UNPACKING ............................................................................................ 3

1-3. ELECTROSTATIC DISCHARGE PRECAUTIONS ................................... 3

1-4. MOTHERBOARD LAYOUT ...................................................................... 4

CHAPTER 2. SETTING UP THE MOTHERBOARD ....................... 5

2-1. JUMPERS AND CONNECTORS.............................................................. 5

2-2. INSTALLING MEMORY.......................................................................... 14

2-3. SHARED VGA MEMORY ....................................................................... 14

2-4. INSTALLING RISER CARD.................................................................... 14

2-5. ASSIGNING IRQs FOR EXPANSION CARDS ....................................... 14

2-6. WATCHDOG TIMER…………………………………………………………. 15

2-7. DIGITAL I/O…………………………………………………………...………. 17

CHAPTER 3. AWARD BIOS SETUP............................................. 18

3-1. STANDARD CMOS FEATURES............................................................. 19

3-2. ADVANCED BIOS FEATURES............................................................... 20

3-3. ADVANCED CHIPSET FEATURES ........................................................ 21

3-4. INTEGRATED PERIPHERALS............................................................... 23

3-5. POWER MANAGEMENT SETUP........................................................... 27

3-6. PnP/PCI CONFIGURATIONS................................................................. 28

3-7. PC HEALTH STATUS ............................................................................. 29

3-8. FREQUENCY/VOLTAGE CONTROL ..................................................... 29

User’s Manual V

CHPATER 4. VGA, LCD, FEATURE.............................................. 31

4-1. VGA FEATURE....................................................................................... 31

4-2. LVDS PANEL AND TV FEATURE ........................................................... 32

4-3. PCI BUS AUDIO ADAPTER FEATURES................................................ 33

4-4. DRIVER UTILITY INSTALLATION GUIDE ............................................. 34

CHPATER 5. LAN ADAPTER ........................................................ 35

5-1. FEATURES ............................................................................................ 35

5-2. UTP CABLE/RJ-45 JACK DEFINITION .................................................. 36

5-3. CONNECTING 100BASE-TX FAST ETHERNET NETWORK ................ 37

5-4. CONNECTING 10BASE-T ETHERNET NETWORK .............................. 37

5-5. 10MBASE/ 100MBASE INSTALLATION NOTICE .................................. 37

5-6. REMOTE BOOT ROM FUNCTION ........................................................ 38

5-7. LED INDICATORS.................................................................................. 38

APPENDIX A: FLASH MEMORY UTILITY.................................... 39

APPENDIX B: CONNECTOR PIN ASSIGNMENT ........................ 40

APPENDIX C: UC-COM56 JUMPER SETTING............................ 41

APPENDIX D: LIMITED WARRANTY ........................................... 42

User’s Manual

Chapter 1. Introduction

1

ENDAT-4066i supports high performance processor of Intel® Pentium4®,

Celeron® and Celeron D ® with 400 and 533 Front Side Bus. It also supports high speed DDR memory with 64-bit wide interfaces with non-ECC DIMM (up to 1GB).

Only Double Data Rate (DDR) SDRAM memory is supported and the speed of memory can be 266, 333 and 400 MHz.

ENDAT-4066i provides an integrated graphics (Intel® Extreme Graphics 2) accelerator delivering cost competitive 3D, 2D, and video capabilities.

ENDAT-4066i video engines support video conferencing and other video applications. Instead of a dedicated local graphics memory interface, ENDAT-4066i uses a UMA configuration for optimal memory utilization and performance that deliver 3D graphics with sharp images, fast rendering, smooth motion and extreme detail.

ENDAT-4066i contains one integrated Serial ATA host controllers capable of independent DMA operation on two ports. The SATA controllers are completely software transparent with the IDE interface, while providing a lower pin count and higher performance. The data transfer rate is up to 150 MB/s.

ENDAT-4066i is an ideal model for various kind of application:

- KIOSK

- Embedded system equipment

2 The ENDAT-4066i System Board

1-1. Features

Basic Feature:

z Board format: Mini-ITX (170mm x 170 mm) z Supports Socket 478 CPU (FSB 533/400 MHz) z Digital I/O: 2 bits in and 2 bits out (3.3V) z Supports DDR 266/ 333/ 400 SDRAM up to 1GB z Serial ATA connector x 1 z Enhance IDE connector x 2 z Multiple I/O ports: COM port x 2; USB (2.0) x 6 z All COM ports with +5V, +12V power selector z CMOS backup: EEPROM backup z Watchdog z

Intel 10/100 LAN and Audio function onboard z With Intel embedded ATX PCI expansion design

Optional features:

z On board chip provides LVDS interface (18/24/36/48 bit, single/dual channels) or TV out signals (composite and S-video) z Second I/O kit for extra 4 COM ports (COM3 to COM6) z RS 422/485 via COM 2 z Barebones system: niche into Unicorn U-8000 Chassis

Full Software Support:

z Drivers for major operating systems and APIs: Windows 9x / ME,

Windows 2000, Windows XP, Direct3D, DirectDraw and DirectShow,

OpenGL ICD for Windows 9x, and 2000, and DXVA for Windows

2000 and Windows XP

User’s Manual 3

1-2. Unpacking

The motherboard comes securely packaged in a sturdy cardboard shipping carton.

In addition to the User's Manual, the motherboard package includes the following items:

ENDAT-4066i System Board

HDD / IO Cables

LCD cable (Optional)

CDROM Driver includes: Drivers for Windows 98, ME, 2000, XP and AMI / AWARD

FLASH ROM utilities.

Driver utilities for on-board VGA drivers, LAN adapter

If any of these items are missing or damage, please contact the dealer from whom you purchase the motherboard. Save the shipping material and carton in the event that you want to ship or store the board in the future.

Note: Please leave the motherboard in its original package until you are ready to install it!

1-3. Electrostatic Discharge Precautions

Make sure you properly ground yourself before handling the motherboard, or other system components. Electrostatic discharge can easily damage the components.

Note: You must take special precaution when handling the motherboard in dry or air-conditioned environments.

4

1-4. Motherboard Layout

The ENDAT-4066i System Board

User’s Manual 5 6 The ENDAT-4066i System Board

Chapter 2. Setting up the Motherboard

Function Jumpers/Connectors

DIGITAL I/O Pin Header J5

CD In & Line Out Pin Header J6

2-1. Jumpers And Connectors

Microphone IN & LINE IN Pin Header J7

LPC Super I/O Connector

Jumpers/Connectors Overview:

Please double-check the insertion and orientation of the LCD cable before applying power. Improper installation will result in permanent

Cooling Fan Connector FAN1, FAN2

damage LCD panel.

J8

P4 Power Supply Connector 2*2 CN2

P4 Power Supply Connector 2*10

LCD Panel Connector

LCD Voltage Selector

Clear CMOS

Pin Header for external device

PS/2 Mouse/KB Pin Header

PS/2 Mouse/KB

USB Port

IDE 1, IDE 2

SATA 1

IDE active LED

External Speaker

Buzzer On/Off

Hardware Reset Switch

Power LED

ATX Power Supply On/Off Switch

WDT Function Enable/Disable

ATXPWR

LVDS1

JP6

JBAT1

JP1

J1

CN1

CN3, J3, J4

IDE1, IDE2

SATA1

J9: Pin 1(-), Pin 2(+)

J9: Pin 3, Pin 6

J9: Pin 4, Pin 5

J9: Pin 7, Pin 8

J9: Pin 9(+), Pin 10(-)

J9: Pin 11, Pin 12

J9: Pin 13, Pin 14

SATA LED

DDR SDRAM socket

LAN Connector

CRT Output

Power Good Selector

COM1 & COM2 Voltage Selector

J9: Pin 15(+), Pin 16(-)

DIMM1

CN3

CN6

JP2

JP4

COM1 CN4

COM2 CN8D1

LPT1 CN5

MIC In, Line In, Line Out

COM2 Pin Header

RS232 / 485 Selector for COM2

CN7

J2

JP3 & JP5

Part 1: Onboard Jumpers

JP1: Pin Header for external device (2.0mm)

Pin No.

1

3

Signal (MS)

MS Data Out

MS Data In

Pin No.

2

4

Signal (KB)

KB Data Out

KB Data In

5

7

9

MS Data Out

MS CK In

KEY

6

8

10

KB CK Out

KB CK In

KEY

11

13

Pin 1-2 *

+5V(DC)

GND

12

14

Default setting is: 1-3, 5-7, 2-4 and 6-8 closes

JP2: Power Good Selector (2.0mm)

+5V(DC)

GND

External Power Good (Default)

Pin 2-3

Voltage

COM1 (JP4)

COM2 (JP4)

+12V(DC)

1-2

7-8

Internal Power Good

JP3, JP5: RS232 / 422 / 485 Selector for COM2 (2.0mm)

TYPE

RS-232 *

RS-422

RS-485

JP5 (3x4/2mm)

1-2, 4-5, 7-8, 10-11

2-3, 5-6, 8-9, 11-12

2-3, 5-6, 8-9, 11-12

JP4: COM1, 2 Voltage Selector (2.0mm)

R.I. *

3-4

9-10

JP3 (2x3/2mm)

1-2

3-4

5-6

+5V(DC)

5-6

11-12

User’s Manual 7

JP6: Voltage Selector for LCD panel (2.0mm)

LCD power

Pin-1, 2

JP6 (2.54mm)

+3.3V

Pin-3, 4

Pin-5, 6 *

+5V

+12V

Caution: Improper setting will damage LCD panel.

UC-COM56: Voltage Selector for COM3~COM6 (2.0mm) (Optional Item)

Voltage

COM4 (JP1), COM6(JP2)

COM3 (JP1), COM5(JP2)

+12V(DC)

1-2

7-8

R.I. *

3-4

9-10

+5V(DC)

5-6

11-12

Part 2: Onboard Connectors

J1: PS/2 Keyboard / Mouse Pin Header Connector (2.54mm)

Pin No. Signal (KB) Pin No. Signal (MS)

1 KB Data 2 MS Data

3 KEY 4 KEY

5

7

9

GND

+5V(DC)

KB_CLK

6

8

10

GND

+5V(DC)

MS_CLK

J2: Box Header Type Connector for COM2 port (RS-232)

Pin No. Function

1 DCD

2

3

4

5

RXD

TXD

DTR

GND


6

7

8

9

10

DSR

RTS

CTS

RI

N.C


J3, J4: USB port (2.54mm)

Pin No.

1

3

5

7

9

Pin No.

1

3

5

7

9

Pin No.

1

3

5

Function

USB_VCC

USBD 2/4-

USBD 2/4+

USB_GND

USB_GND

J5: DIGITAL I/O (2.54mm)

Function

DIO-O0

DIO-O1

+12V

KEY

GND

Function

LO_J_R

GND_AUD

GND_AUD

Pin No.

2

4

6

8

10

Pin No.

2

4

6

8

10

J6: CD IN, LINE OUT (2.54mm)

Pin No.

2

4

6

7 LO_J_L 8

J7: Microphone IN & LINE IN (2.54mm)

Function

USB_VCC

USBD 3/5-

USBD 3/5+

USB_GND

USB_GND

Function

DIO-I0

DIO-I1

+12V

+3.3V

GND

Function

CDR

CDGND

CDGND

CDL

Pin No.

1

3

5

7

Function

MICIN1

GND

GND

MICIN2

Pin No.

2

4

6

8

Function

LINE_R

GND

GND

LINE_L

User’s Manual 9

1

3

5

7

9

11

13

15

17

19

J9: Header for Case Panel (2.54mm)

Pin No.

1(-), 2(+)

Function

IDE active LED

3,6

4,5

External Speaker

Buzzer On/Off

7,8

9(+), 10(-)

11,12

Hardware Reset Switch

Power LED

ATX Power On/Off

13,14

15(+), 16(-)

Close: Enable WDT function

SATA active LED

ATXPWR: Power Supply Connector (3.96mm)

Pin No. Function Pin No. Function

+3.3V

+3.3V

GND

+5V

GND

+5V

GND

POWER OK

5V_SB

+12V

2

4

6

8

10

12

14

16

18

20

+3.3V

-12V

GND

PS-ON

GND

GND

GND

-5V

+5V

+5V

CN2: Power Supply Connector (3.96mm)


1

3

GND

GND

Pin No.

2

4

Function

+12V

+12V

FAN1, FAN2: CPU / 2nd Cooling Fan Connector


1 Sensor Pin.

2

3

+12V

GND


CN5: Printer (LPT1) Port

Pin No.

Description Pin No. Description

1

2

3

4

STB#

PD0

PD1

PD2

10

11

12

13

ACK#

BUSY

PE

SLCT

5

6

PD3

PD4

14

15

AFD#

ERR#

7

8

PD5

PD6

9 PD7

CN6: CRT Connector

16

17

18-25

INIT#

SLIN#

GND

Pin No.


1 RED 9 N.C / +5V

2

3

4

5

GREEN

BLUE

N.C

GND

10

11

12

13

GND

N.C

DDC DAT

H-Sync

6

7

GND

GND

14

15

V-Sync

DDC CLK

8 GND

D-SUB Type Connector for COM2 port (RS-422 Æ 4 Wire)

Pin No.

Function Pin No. Function

1

2

3

4

5

–TXD

+RXD

6

7

NA

NA

+TXD

NA

8

9

NA

–RXD

NA

User’s Manual 11

D-SUB Type Connector for COM2 port (RS-485 Æ 2 Wire)

Pin No. Function Pin No. Function

1

2

Data –

NA

6

7

NA

NA

3

4

5

Data +

NA

8

9

NA

NA

NA

D-SUB Type Connector for COM port (RS-232)

Pin No. Description Pin No. Description

1

2

3

DCD

RXD

TXD

6

7

8

DSR

RTS

CTS

4 DTR 9 RI

5 GND

IDE1 Connector

Pin No. Description Pin No. Description

2,19,22

24.26.30

40

20,21,28

29,32,34

1

3

4

GND

GND

GND

N.C

N.C

IDE reset

IDE data7

IDE data8

13

14

15

16

17

18

23

25

IDE data2

IDE data13

IDE data1

IDE data14

IDE data0

IDE data15

IDE Write

IDE Read

9

10

11

12

5

6

7

8

IDE data6

IDE data9

IDE data5

IDE data10

IDE data4

IDE data11

IDE data3

IDE data12

36

37

38

39

27

31

33

35

IDE Ready

IDE IRQ

IDE A1

IDE A0

IDE A2

IDECS1#

IDESC3#

HDLED0#


IDE2: Slim IDE2 Connector (44Pins with 2.0mm)

Pin No.


1 IDE Reset# 2 GND

3

5

7

9

11

13

IDE data7

IDE data6

IDE data5

IDE data4

IDE data3

IDE data2

4

6

8

10

12

14

IDE data8

IDE data9

IDE data10

IDE data11

IDE data12

IDE data13

15

17

19

21

23

25

27

29

31

33

35

37

39

41

43

IDE data1

IDE data0

GND

IDE REQ

IDE IOW#

IDE IOR#

IDE Ready

IDE ACK#

IDE IRQ

IDE A1

IDE A0

IDECS1#

HDLED#

VCC(+5V)

GND

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

IDE data14

IDE data15

N.C.

GND

GND

GND

GND

GND

N.C.

P66DET

IDE A2

IDESC3#

GND

VCC(+5V)

N.C.

User’s Manual 13

LVDS1: Dual LVDS Channel (2.0mm)

13

15

17

19

21

23

1

3

5

7

9

11

25

27

29

31

33

35

37

39

VBL (+12V)

GND

DISP.ON/OFF

LVDD

GND

TxO0+

TxO1+

TxO2+

TxO3+

TxOC+

GND

TxE0+

TxE1+

TxE2+

TxE3+

TxEC+

LVDD

GND

GND

VBL (+12V)

14

16

18

20

22

24

2

4

6

8

10

12

26

28

30

32

34

36

38

40

VBL (+12V)

GND

GND

LVDD

GND

TxO0-

TxO1-

TxO2-

TxO3-

TxOC-

KEY

TxE0-

TxE1-

TxE2-

TxE3-

TxEC-

LVDD

GND

GND

VBL (+12V)

Please make sure the Pin 1 location before inserting the LCD connector.

LCD panel ID:

ID No.

1

Resolution

800 x 600 with 18bit

2

3

4

1024 x 768 with 24bit

1280 x 1024 with 48bit

1280 x 768 with 24bit


2-2. Installing Memory

ENDAT-4066i system board offers one 184pin DDR SDRAM socket supports up to

1GB memory and the speed can be 200/ 266/ 333/ 400.

2-3. Shared VGA Memory

ENDAT-4066i is using built-in AGP VGA controller with INTEL DVMT up to 96MB of system memory. The amount of video memory on motherboard determines the number of colors and the video graphic resolution.

2-4. Installing Riser Card

Installing Riser Card (Max. 3 PCI Slots on Riser Card)

PCI Slot INT

PCI 1 A,B,C,D

PCI 2 B,C,D,A

PCI 3 C,D,A,B

PCI 4 D,A,B,C

ADSEL

AD20

AD22

AD23

AD25

The default INT/AD-select for ENDAT-4066i All-In-One motherboard is listed in the above table.

2-5. Assigning IRQs for Expansion Cards

Some expansion cards require an IRQ (Interrupt request vector) to operate.

Generally, each IRQ must be exclusively assigned to specific use. In a standard design, there are 16 IRQ available with 11 of them already in used by other part of the system.

Some PCI expansion cards need IRQ; any remaining IRQ could be assigned to PCI

Bus. Microsoft's Diagnostic (MSD.EXE) utility included in the Windows directory can be used to see their map. Clients can not have more than one device apply the same IRQ in the system or it will cause the system hang up, crash, and unexpected results. To simplify the process, this motherboard complies with the Plug and Play

(PnP) specifications, which was developed to allow automatic system configuration.

Whenever a PnP-compliant card is added to the system, PnP card and IRQs will automatically assigned if available. The PCI and PnP configuration in the BIOS setup utility can indicate which IRQs have being used by Legacy cards.

In the PCI Bus design, the BIOS is automatically assigned an IRQ to a PCI slot that

User’s Manual 15 has a card in it which requires an IRQ. To install PCI cards via riser card, you need to set the correct "ADSEL" and "INT" (interrupt) assignment on the jumper of riser card.

14

15

Used Hard Disk (IDE 1)

Used Reserved (IDE 2)

2-6. Watchdog Timer

Watchdog Timer (WDT) is a special design for system monitoring to secure the system work normally. WDT has an independent clock from the oscillator and could set time and clear/refresh WDT counter function. When time is up, WDT will send hardware RESET signal to reset system.

Timeout Value Range

-1 to 255

-Second or Minute


Program Sample

#include <stdio.h>

#include <dos.h>

#include <dir.h> void show_ver(); void main()

{ unsigned int tt;

clrscr();

show_ver();

tt=0;

while((tt==0)||(tt>255))

{ printf("\n\nPlease key in how many seconds you want to reset system

(1~255):");

scanf("%d",&tt);

} outportb(0x2e,0x07); //Set Logic Device number pointer outportb(0x2f,0x08); //Set Logic Device number outportb(0x2e,0xf5); //Set active register is CRF5 outportb(0x2f,0x00); //Set register value (bit3=1: minute. =0: second) outportb(0x2e,0xf7); //Set active register is CRF7 outportb(0x2f,0x00); //Disable all WDT interrupt (bit7=Mouse, bit6=Keyboard) outportb(0x2e,0xf6); //Set active register is CRF6 outportb(0x2f,tt); //Set time out value of WDT

} void show_ver()

{ unsigned char tmp0; printf("Designed by ROBERT LIOU of UNICORN computer corp.

\n2004/03/02 release version:1.0a\n"); printf("This program is design for test Watchdog Timer for W83627.\n");

}

User’s Manual 17

2-7. Digital I/O

1) Pin out of digital I/O header (J13):

1

3

5

7

9

DIO-O0

DIO-O1

+12V

KEY

GND

2

4

6

8

10

DIO-I0

DIO-I1

+12V

+3.3V

GND

2) Digital input control port (48Fh):

The digital input port can be read directly from port address “48Fh” (data mapping to bit0 for I0 and bit3 for I1 and the default value is “1Bh”. The input level is 3.3V (+/-5% tolerance).

The sample code is shown below (using TurboC/C++ 3.0):

#define INPUT_PORT 0x48f unsigned char read_data; read_data=inportb(INPUT_PORT); //Read status from INPUT port

Attention: The SB chip might be damaged by over specifying voltage.

3) Digital output control port (48Eh):

The digital output port can be written directly by porting address “48Eh” (data mapping to bit5 for OUT0 and bit2 for OUT1.

The sample code is shown below (using TurboC/C++ 3.0):

#define OUT_PORT 0x48e outportb(OUT_PORT,0x20); //Set OUT0 as logic “1” and OUT1 as “0” outportb(OUT_PORT,0x04); //Set OUT1 as logic “1” and OUT0 as “0” outportb(OUT_PORT,0x24); //Set OUT0 and OUT1 as logic “1”


Chapter 3. AWARD BIOS SETUP

Phoenix – Award BIOS CMOS Setup Utility

> Standard CMOS Features

> Advanced BIOS Features

> Advanced Chipset Features

> Integrated Peripherals

> Power Management Setup

> PnP/PCI Configurations

> PC Health Status

> Frequency/Voltage Control

> Load Fail-Safe Defaults

> Load Optimized Defaults

> Set Supervisor Password

> Set User Password

> Save & Exit Setup

> Exit Without Saving

Use the CMOS setup program to modify the system parameters to reflect the environment installed in your system and to customize the system as desired.

Press the <DEL> key to enter into the CMOS setup program when you turn on the power. Settings can be accessed via arrow keys. Press <Enter> to choose an option to configure the system properly.

In the main menu, press F10 or “SAVE & EXIT SETUP” to save your changes and reboot the system. Choose “EXIT WITHOUT SAVING” to ignore the changes and exit the setup procedure. Pressing <ESC> at anywhere during the setup will return to the main menu.

“Advanced BIOS Features”, “Advanced Chipset Features” and “PnP/PCI

Configurations” requires board knowledge on PC/AT system architecture and Intel chipset specification. They intend to be used by well-trained technicians and experienced users. Press the <F6> key to save CMOS setting to EEPROM, Press

<F7> key can load CMOS setting from EEPROM. Incorrect setup could cause system malfunctions.

User’s Manual 19

3-1. Standard CMOS Features

The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Hard Disk Drive settings.

Item

Date (mm:dd:yy)

Time (hh:mm:ss)

IDE Channel 0 Master:

IDE Channel 0 Slave :


IDE Channel 1 Slave :



Video

Halt On

Available Options:

Auto

Auto

Auto

Auto

Auto

Auto

EGA/VGA

All , But Keyboar


3-2. Advanced BIOS Features

This section allows you configuring your system for basic operation. You have the opportunity to select the system’s default speed, boot-up priority, keyboard operation and security.

Item

CPU Feature

Hard Disk Boot Priority

Virus Warning

CPU L1 & L2 Cache

Quick Power On Self Test

USB Flash Disk Type

Press Enter

Press Enter

Enabled

Enabled

Enabled

Auto


First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Boot Up NumLock Status

Gate A20 Option

Typematic Rate Setting

Hard Disk

CDROM

Disabled

Enabled

On

Fast

Disabled

Typematic Rate (Chars/Sec)

Typematic Delay (Msec)

Security Option

APIC Mode

MPS Version Control For OS

OS Select For DRAM > 64MB

Report No FDD for WIN 95

Delay For HDD (Secs)

6

250

Setup

Enabled

1.4

Non-OS2

Yes

0

Enabled Small Logo(EPA) Show

․

APIC Mode

This item can enable or disable the APIC (Advanced Programmable Interrupt

Controller). Due to compliance to PC2001 design guide, the system is able to run in APIC mode. Enabling APIC mode will expand available IRQs resources for the system. Leave this field in its default setting.

․

MPS Version Control For OS

This item allows you selecting which MPS (Multi-Processor Specification) version to be used for the operating system. You need to select the MPS version

User’s Manual 21 that is supported by your operating system. To find out which version to use, consult the vendor of your operating system.

3-3. Advanced Chipset Features

This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications with the PCI bus.

It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system. You might consider making any changes only if you discover that the data has been lost while using your system.

Item

DRAM Timing Selectable

CAS Latency Time

Active to Precharge Delay

DRAM RAS# to CAS# Delay

DRAM RAS# Precharge

Memory Frequency For

System BIOS Cacheable

Video BIOS Cacheable

AGP Aperture Size (MB)

Init Display First


By SPD

2

6

3

3

Auto

Enabled

Enabled

128

Onboard/AGP

On Chip VGA Enabled

On Chip Frame Buffer Size 16MB

Boot Display CRT

1 Panel Number

․

Memory Frequency For

This main board supports different memory frequencies depend on the CPU FSB

(Front Side Bus) and the type of DDR DIMM.

533 MHz

400 MHz

PC2700/PC2100

PC2100

333/266 MHz

266 MHz


․

AGP Aperture Size (MB)

This function determines the amount of system memory that is given to the AGP card. This is a dynamic memory allotment in that the AGP card will only use the amount of memory that it needs. The remaining memory, which is not in use, will be available for the system.

․

On-Chip Frame Buffer Size

This field is used to select the onboard VGA’s frame buffer size that is shared from the system memory.

․

Boot Display

This field is used to select the type of display to use when the system boots.

CRT

LFP

CRT+LFP

TV

Select this option if you want the system to boot the CRT display.

Select this option if you want the system to boot the LCD flat panel display.

(Optional Item)

Select this option if you want the system to boot both the CRT and LCD flat panel display. (Optional Item)

Select this option if you want the system to boot the TV display.

(Optional Item)

․Panel Number

(Optional Item)

1

2

3

4

800x600, one channel LVDS for 18-bit panels

1024x768, one channel LVDS for 24-bit panels

1280x1024, tow channel LVDS for 48-bit panels

1280x768 (16: 9), one channel LVDS for 24-bit panels

If you apply one of the standard panels shown above, select the appropriate option according to the type of panel that you apply. Or, please contact your dealer or sales representative for custom-made BIOS that will suit the panel that you apply.

․TV Format

(Optional Item)

Auto / NTSC_M / NTSC_M_J / NTSC_433 / NTSC_N / PAL_B PAL_G / PAL_D /

PAL_H / PAL_I / PAL_M / PAL_N / PAL_60 SECAM_L / SECAM_L1 / SECAM_B

/ SECAM_D / SECAM_G SECAM_H

User’s Manual 23

․CPU to PCI Write Buffer

When enabled, up to four D words of data can be written to the PCI bus without interrupting the CPU. When disabled, a write buffer is not used and the CPU read cycle will not be completed until the PCI bus signals is ready to receive the data.

․PCI Delay Transaction

The chipset has an embedded 32-bit posted write buffer to support delay transaction cycles. Select Enabled to support compliance with PCI specification version 2.2.

․OnChip USB

Select “Enabled” if your system contains a Universal Serial Bus (USB) controller and you have a USB peripheral. The “Assign IRQ for USB” has to be set to

Enabled on “PnP/PCI Configuration” (when the USB be used.)

․Onboard LAN Boot ROM

The default setting is enabled or disabled LAN boot up function.

3-4. Integrated Peripherals

The IDE hard drive controllers support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks.

Integrated Peripherals

Item

OnChip IDE Device

Onboard Device

Super IO Device

Onboard Serial Port 3

Serial Port 3 Use IRQ








Press Enter

Press Enter

Press Enter

3E8

IRQ5

2E8

IRQ5

4F8

IRQ5

4E8

IRQ5


OnChip IDE Device

Item

IDE HDD Block Mode

On-Chip Primary PCI IDE

IDE Primary Master PIO

IDE Primary Slave PIO

IDE Primary Master UDMA

IDE Primary Slave UDMA

On-Chip Secondary PCI IDE

IDE Secondary Master PIO

IDE Secondary Slave PIO

IDE Secondary Master UDMA

IDE Secondary Slave UDMA

On-Chip Serial ATA

Serial ATA Port0 Mode

Serial ATA Port1 Mode


Enabled

Enabled

Press Enter

Auto

Auto

Auto

Enabled

Auto

Auto

Auto

Auto

Auto

SATA0 master

SATA1 master

․

IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or multiple sectors read/write.

․

IDE Primary Master/Slave PIO and IDE Secondary

Master/Slave PIO

The four IDE PIO (programmed Input/Output) fields let you set a PIO mode (0-4) for each IDE device that the internal PCI IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.

․

IDE Primary Master/Slave UDMA and IDE Secondary

Master/Slave UDMA

These fields allow you to set the Ultra DMA in use. When Auto is selected, the

BIOS will select the best available option after checking your hard drive or

CD-ROM.

User’s Manual 25

․

On-Chip Serial ATA

Disabled

Auto

Combined Mode

Enhanced Mode

SATA Only

Disables the onboard SATA.

The system will detect the existing SATA and IDE drives then automatically set them to the available master/slave mode.

This option allows you to use both IDE and SATA drives; allowing a maximum of 4 drives. You must manually set the SATA drives’ master/slave mode in the “Serial ATA

Port0 Mode” and “Serial ATA Port1 Mode” fields.

This option allows you to use both IDE and SATA drives; allowing a maximum of 6 drives.

This option automatically sets the SATA drives to Primary

Master and Secondary Master modes. Since both drives are in master mode, you cannot set the IDE drives to Master mode. The “Serial ATA Port0 Mode” and “Serial ATA

Port1 Mode” fields will not be configurable.

․

Serial ATA Port0 Mode and Serial ATA Port1 Mode

These fields are used to select the master/slave mode of the serial ATA drives.

Make sure they do not conflict with the settings of the IDE hard drives.

Onboard Device

Item

USB Controller

USB 2.0 Controller

USB Keyboard Support

USB Mouse Support

AC97 Audio

Onboard LAN Boot ROM

Onboard CSA LAN Boot ROM

CSA LAN (Giga-LAN)


Enabled

Enabled

Enabled

Disabled

Enabled

Enabled

Enabled (Optional Item)



Item

POWER ON Function

KB Power ON Password

Hot Key Power ON



UART Mode Select

RxD, TxD Acitve

IR Transmission Delay

UR2 Duplex Mode

Use IR Pins

Onboard Parallel Port

Parallel Port Mode

EPP Mode Select

ECP Mode Use DMA

PWRON After PWR-Fail

SuperIO Device


Button ONLY

Enter

Ctrl-F1

3F8/IRQ4

2F8/IRQ3

Normal

Hi,Lo

Enabled

Half

IR-Rx2Tx2

378/IRQ7

SPP

EPP1.9

3

Off

User’s Manual 27

3-5. Power Management Setup

The Power Management Setup allows users configuring the system to save energy in a most effective way while operating in a manner consistent with their own style of computer use.

Item

ACPI function

ACPI Support Type

Run VBIOS if S3 Resume

Power Management

Video Off Method

Video Off In Suspend

Suspend Type

Suspend Mode

HDD Power Down

Soft-Off by PWR-BTTN

Wake Up by PCI Card

Power On by Ring

Wake Up On LAN

Resume by Alarm

Date(of Month) Alarm

Time(hh:mm:ss) Alarm

Primary IDE 0

Primary IDE 1

Secondary IDE 0

Secondary IDE 1

FDD,COM,LPT Port

PCI PIRQ[A-D]#


Enabled

S1(POS)

Auto

User Define

DPMS

Yes

Stop Grant

Disabled

Disabled

Instant-Off

Enabled

Enabled


Disabled

0

0 : 0 : 0

Disabled

Disabled

Disabled

Disabled

Disabled

Disabled

․

ACPI Function

This function should be enabled only in operating systems that support ACPI.

Currently, only Windows® 98SE/2000/ME/XP supports this function. When this field is enabled, the system will ignore the settings in the “Suspend Mode” and

“HDD Power Down” fields. If you want to use the Suspend to RAM function, make sure this field is enabled then select“S3 (STR)” in the field below.

․

ACPI Suspend Type

This field is used to select the type of Suspend mode.

S1(POS)

S3(STR)

S1 & S3

Enables the Power On Suspend function.

Enables the Suspend to RAM function.

If S3 state is supported by the system, by default [S3] is automatically selected. Otherwise [S1] is selected.


3-6. PnP/PCI Configurations

This section describes the configuration of the PCI bus system. PCI is a system that allows I/O device to operate at speeds nearing the speed of the CPU itself, when communicating with its own special components. This section covers some very technical items. It is strongly recommended that only experienced users make any changes to the default settings.

Item

Reset Configuration Data

Resources Controlled By

IRQ Resources

IRQ-3 assigned to










PCI/VGA Palette Snoop

․



Disabled

Auto(ESCD)

Press Enter

Reserved

Reserved

PCI Device

Reserved

PCI Device

PCI Device

PCI Device

PCI Device

PCI Device

PCI Device

Disabled

Enabled

The BIOS will reset the Extended System Configuration Data

(ESCD) once automatically. It will then recreate a new set of configuration data.

The BIOS will not reset the configuration data. Disabled

․


Auto(ESCD) The system will automatically detect the settings for you.

Manual Choose the specific IRQ in the “IRQ Resources” field.

․

PCI/VGA Palette Snoop

When set to [Enabled], multiple VGA devices operating on different buses can handle data from the CPU on each set of palette registers on every video device.

Bit 5 of the command register in the PCI device configuration space is the VGA

Palette Snoop bit (0 is disabled).

User’s Manual 29

3-7. PC Health Status

This screen shows the information of temperature, Fan speed and Vcore etc. It also can set CPU warning temperature to protect CPU.

PC Health Status

Item

Shutdown Temperature

CPU Warning Temperature

Current System Temp


H/W CHK

Enabled

42℃/ 107℉

Current CPU1 Temperature 28℃/ 82℉

Current CPU2 Temperature

Fan1 Speed

Fan2 Speed

Vcore

VIN0

VIN1

VIN2

VCC (V)

VBAT (V)

5VSB (V)

3-8. Frequency / Voltage Control

53℃/ 127℉

2556 RPM

0 RPM

1.45V

3.34V

11.79V

-11.84V

5.10V

3.24V

5.07V

Frequency/Voltage Control

Item

CPU Clock Ratio

Auto Detect DIMM/PCI Clk

Spread Spectrum


18 X

Enabled

Disabled

․CPU Clock Ratio

The frequency ratio of some processors may have been locked by the manufacturer. If you are using this kind of processor, setting an extended ratio for the processor will have no effect. The system will instead use its factory default ratio.

․Auto Detect DIMM/PCI Clk

When enabled, the system will automatically send clock signals to existing PCI devices.


․Spread Spectrum

Leave this field in its default setting. Do not alter this setting unless advised by an engineer or technician.

User’s Manual

Chapter 4. VGA, LCD Feature

31

ENDAT-4066i provides an integrated graphics (Intel® Extreme Graphics 2) accelerator delivering cost competitive 3D, 2D, and video capabilities. It contains an extensive set of instructions for 3D operations, BLT (Block Level Transfers) and

Stretch BLT operations, motion compensation, overlay, and display control.

ENDAT-4066i video engines support video conferencing and other video applications. Instead of a dedicated local graphics memory interface,

ENDAT-4066i applies UMA configuration for optimal memory utilization and performance that deliver 3D graphics with sharp images, fast rendering, smooth motion and extreme detail.

High bandwidth access to data is provided through the system memory port.

ENDAT-4066i can access local graphics data located in system memory at 2.1

GB/s (DDR266) 2.7 GB/s (DDR333), or 3.2 GB/s (DDR400) in single-channel mode.

ENDAT-4066i applies Intel® DVMT for optimum the system utilization via system chipset. DVMT is a concept be applied in the Intel® 865GV chipset wherein the optimum amount of memory is dynamically allocated and de-allocated as needed for balanced graphics and system performance, through Intel® Direct AGP and a highly efficient memory utilization scheme.

The on-board Graphics Controller supports a full AGP implementation internally to remain compatible with existing software and programming models. However, since the engine is integrated, it enjoys a higher bandwidth and lower latency than is possible with discrete solutions.

The controller of ENDAT-4066i supports 2 types of display: CRT and LVDS panel .


4-2. LVDS Panel And TV Feature (optional)

These 2 devices are alternate feature; can not exist on the same system at the same time.

LVDS Panel Interface

The on-board graphic controller supports industry standard LCD panel, LVDS interface only, with 1 channel (18 or 24) and 2 channels (36 or 48bit) data width.

LVDS interface provides low voltage, high speed and low EMI serial DC-balanced differential data via optional onboard LVDS.

The flat panel interface provides or supports following functions for various panels:

- Generates LVDS flat panel channels like clock and data channel.

- Generates different video data formats to directly drive different types of panels (18, 24, 36 or 48bit)

- Wide screen resolution as 16:9 or 16:10.

- Vertical and horizontal expansion of video displays to LCD panel resolution

- Vertical and horizontal centering

Please note that the default setting is with “CRT only”. If the LCDdisplay features is required, the setting will need to be revised in the system BIOS setting: “Display Device” under “Advanced Chipset Features” unless clients specified the display type while order.

User’s Manual 33

4-3. PCI Bus Audio Adapter Features

The Chipset built-in SoundBlaster Pro Hardware and Direct Sound Ready AC97’

Digital Audio Controller

•

Dual full-duplex direct sound channels between system memory and AC97’ link

•

PCI Master interface with scatter / gather and bursting capability

•

32byte FIFO of each direct sound channel

•

Host based sample rate converter and mixer

•

Standard v1.0 or v2.0 AC98’ Codec interface for single or cascaded AC97’

Codec’s from multiple vendors

•

Loop back capability for re-directing mixed audio streams into USB and 1394 speakers

• Hardware SoundBlaster Pro for Windows DOS box and real-mode DOS legacy compatibility

•

Plug and Play with 4 IRQ, 4 DMA and 4 I/O space options for SoundBlaster Pro and MIDI hardware

•

Hardware assisted FM synthesis for legacy compatibility

• Complete software driver support for Windows-95, Windows-98 and

Windows-NT


4-4. Driver Utility Installation Guide

When finishing the installation of Windows platform (98/ME/2000/XP), please install the relative “INF” driver of Intel® chipsets firstly for compliance compatibility of hardware environment.

Please follow the step of CD-ROM driver and complete the VGA, AUDIO,

ETHERNET and USB2.0 setup procedure. Insert the support CD that supplied with motherboard into CD-ROM driver, which enable the access with auto-run mode; or double –click the CD driver icon in “My Computer” to bring up the screen.

Please download or check from Intel® Web site: www.intel.com

if you prefer to install the drivers individually or you need more information.

User’s Manual

Chapter 5. LAN Adapter

35

The on-board LAN adapter integrated of Single Chip Fast Ethernet Controller with options of one or dual LAN solution. It is highly integrated and requires no “glue” logic external memory on board. It runs in the bus master mode and directly sending/receiving Ethernet packet to/from memory. The On-board LAN adapter can directly fetch the system CPU. Also, it can transfer data Directly between I/O devices and system memory in the 32-bit bus master mode that provides low CPU utilization.

It complies with the IEEE 802.3x standard, IEEE802.3 standard and PCI Local Bus version 2.1 and transmits data on the network at 100 Mbps or 10 Mbps. It also operates in full-duplex mode that doubles the network speed up to 20/200 Mbps

when working with Fast Switching Hub. Built-in one RJ-45 port for connection of

100Base-TX Fast Ethernet or 10Base-T Ethernet network, and automatically senses the connection type.

5-1. Features

•

Full compliancy with PCI Rev. 2.1

•

Complies with the Ethernet/IEEE 802.3u 100Base-TX and 10 Base-T industry standard

• Supports full-duplex operations, thus doubling the network speed up to

20Mbps on 10 Base-T Ethernet or 200Mbps on 100 Base-TX Fast Ethernet when setting in full duplex mode

•

Two LED indicators to report network status

•

One RJ-45 connector with Auto-sense cable type of 10 or 100Mbps network operation

•

Supports PCI clock speed up to 33MHz, capable of zero wait states

•

Supports Remote Boot ROM by system BIOS

• Provides a comprehensive setup program for displaying the adapter configuration and includes diagnostic on board or network tests

•

Complete drivers for Novell, Windows NT and Windows 95/98 Packet driver etc


5-2. UTP Cable / RJ-45 Jack Definition

Straight through twisted pair cable is typically used to connect a hub to a server or workstation. In a straight through connection, Pin 1 at the server, Pin 2 at the hub connects to Pin 2 at the server, and so on. Figure A-1 shows the locations of pins on a standard RJ-45 plug on a twisted-pair cable.

Table A-1 shows the wiring in a straight-through twisted-pair cable (Pins 4, 5, 7 and

8 are not used).

Twisted Pair

Number

1

2

Pin Number

1

2

3

6

Signal

Description

TD+

TD–

RD+

RD–

To Pin Number

Æ

Æ

RJ-45 Connector Pin Assignments

1

2

3

6

Signal

Description

TD+

TD–

RD+

RD–

Figure A-1 shows the RJ-45 Connector pin assignments

User’s Manual 37

5-3. Connecting 100Base-TX Fast Ethernet Network

The system board provides an RJ-45 port for connection to 100Base-TX Fast

Ethernet or 10Base-T Ethernet Network with a single connection over unshielded twisted-pair (UTP). The adapter automatically operates at 10Mbps or 100Mbps when the appropriate 10/100Base hub is connected.

To connect the adapter to 100Base-TX Fast Ethernet Network, you need a twisted-pair Category 5 cable with RJ-45 modular jacks at both ends. This cable can have a maximum length of 300 feet (100 meters).

5-4. Connecting 10Base-T Ethernet Network

To connect the adapter to a 10Base-T Ethernet Network, you need a twisted-pair

Category 3, 4 or 5 cables with RJ-45 modular jacks at both ends. This cable can have a maximum length of 300 feet (100 meters).

5-5. 10MBase/100MBase Installation Notice

•

100Mbps network must be shielded twisted-pair (STP) or Category 5 unshielded twisted-pair cable. Do not use a Category 3 or 4 cable for 100Mbps-network operation, it could cause data loss. Category 3 or 4 cable is good for 10Mbps network only.

•

Category 5 cable is also good for 10Mbps operation. Use UTP Category 5 cable for the versatility to operate the network at either 100Mbps or 10Mbps speed without changing cable.

•

•

Two pairs of wiring are required.

Depending on building codes, different insulation materials may be required.

Plenum-rated or TEFLON-coated wiring maybe required in some areas where fireproofing is required.

•

The wire gauge should be between 18 and 26 AWG (Most telephone installations use

24-gauge wiring).

•

UTP cable should meet the following requirements:

2. Nominal capacitance: less than 16pF/ft

3. Nominal impedance: 100 ohms

4. Nominal attenuation: less than 11.5db


Automatic Selection of the Media Type

While the driver installs, it automatically detects the media type based on the type of cable connected. Once you change the cable type, you must reinstall the driver to execute auto-detect again.

If the driver cannot detect which cable is connected or whether a cable is connected, look at cabling network driver (Ex. Modify net.cfg file parameters—force line speed=10 or 100).

10/100 Auto – Negotiation (N-Way)

Depending on the hub or connected device, the LAN adapter can automatically run at the appropriate speed, by using N-way, a feature that complies with the

IEEE802.3 standard. It also works with any of the other IEEE-compliant products.

5-6. Remote BOOT ROM Function

This function is available with the BIOS programming for indicated operation system. The remote boot function allows the computer to boot up over the network, instead of using the local operating system device. This enables the system to be a diskless workstation environment.

5-7. LED Indicators

The system board comes with two LED indicators on the edge of the motherboard that indicates the network system status. If you experience any problems with the adapter, first make sure the appropriate driver is loaded, the proper cable is connected to the RJ-45 port and the hub complies with the adapter specification, such as 10Mbps 10Base-T or 100Mbps 100Bast-TX. Finally, recheck the LEDs.

FUDUP (Full Duplex) Indicator

When indicator is ON, it indicates Full-duplex mode: otherwise, it is OFF. The adapter supports full duplex at 10 or 100Mbps. If the switch-hub supports the

N-way feature and full duplex, the system will automatically runs in full duplex mode.

Tx/Rx (Transmit/Receiver) Indicator

This indicator flashes to display that there is network activity – indicating transmission or reception data from the network.

User’s Manual 39

Appendix A: FLASH Memory Utility

Using this utility to update the system BIOS from a disk file to the on board Flash memory. Be aware the improper change of the system BIOS will cause the system to malfunction.

Using utility as follows:

1. Insert the FLASH memory utility distribution floppy diskette in drive A:

2. At the DOS prompt, type A:>AWDFLASH and press <Enter>

AwardBIOS FLASH Utility V8.36E

C>Phoenix Technologies Ltd. All Rights Reserved

Flash Type –

File Name to Program:

Message:

3. Enter the name of the system BIOS disk file into the "File Name to Program" field

The following message appears in the "Message" field

4. Do you want to save BIOS (y/n)?

5. To update the FLASH memory from the system BIOS disk file, type Y

6. After complete updating, please re-boot the system (press “F1” key)

7. For upgrade BIOS procedure, please refer to our web site:

http://www.unicorn-computer.com.tw

* Please turn off system and clear CMOS data by JP8.

* Please restart your system and load optimal defaults setting.


Appendix B: LCD Pin Assignment

23

25

27

29

31

33

35

37

39

1

3

5

7

9

11

13

15

17

19

21

LVDS1:

Dual Channel

LVDS (2.54mm)

VBL (+12V)

GND

DISP.ON/OFF

LVDD

GND

TxO0+

TxO1+

TxO2+

TxO3+

TxOC+

GND

TxE0+

TxE1+

TxE2+

TxE3+

TxEC+

LVDD

GND

GND

VBL (+12V)

24

26

28

30

32

34

36

38

40

2

4

6

8

10

12

14

16

18

20

22

VBL (+12V)

GND

GND

LVDD

GND

TxO0-

TxO1-

TxO2-

TxO3-

TxOC-

KEY

TxE0-

TxE1-

TxE2-

TxE3-

TxEC-

LVDD

GND

GND

VBL (+12V)

Please make sure the Pin 1 location before inserting the LCD connector.

BIOS LCD panel type list (Advance Chipset Setup/Panel Type)

ID No.

1

2

3

4

Resolution

800 x 600 with 18bit

1024 x 768 with 24bit

1280 x 1024 with 48bit

1280 x 768 with 24bit

User’s Manual 41

Appendix C: UC-COM56 Jumper Setting


Voltage

COM4 (JP1)

COM3 (JP1)

+12V(DC)

1-2

7-8

R.I. *

3-4

9-10


Voltage

COM6 (JP2)

COM5 (JP2)

+12V(DC)

1-2

7-8

R.I. *

3-4

9-10

+5V(DC)

5-6

11-12

+5V(DC)

5-6

11-12

J2: Digital I/O Box Header Connector (2.54mm)

Pin No.

1

3

5

7

9

Function

DIO-O0

DIO-O1

+12V

KEY

GND

Pin No.

2

4

6

8

10

Function

DIO-I0

DIO-I1

+12V

+5V

GND


Appendix D: Limited Warranty

Standard two years limited warranty on all our ENDAT series all-in-one motherboards and embedded boards. Products that become defective during the warranty period shall be repaired, or subject to manufacturer’s option, replaced.

The limited warranty applies to normal proper usage of the hardware and does not cover products that have been modified or subjected to unusual electrical or physical stress. Unicorn Computer Corp is not liable to repair or replace defective goods caused by improper using or use of unauthorized parts. The following situations will be charged:

1. The products during the warranty but defective caused by improper using or artificial external pressure and result in the components damages. According to the damage situation, the manufacturer has the rights to decide to repair or not.

The manufacturer will charge the parts/repair cost and the returning shipping charge.

2. The products out of warranty will charge the parts/repair cost and the returning shipping charge as per the repair status.

3. The manufacturer has the rights to decide to repair or not based on the stock of parts for the products which are phased out of the production.

4. Please e-mail or fax the RMA Service Request Form when have the defective products.

User’s Manual 43

RMA SERVICE REQUEST FORM

When requesting RMA service, please fill out this “RMA Service Request Form”.

This form needs to be shipped with your returns. Service cannot begin until we have this information.

RMA NO.:

Company: Person to Contact:

Phone No: Purchase Date :

Fax No. : Applied Date :

Return Shipping Address:

Model No. Serial No. Problem Code Remark

44 The ENDAT-4066i System Board z Issue Code of defect.

01 Second Times R.M.A.

02 No Screen (No Boot)

03 VGA (Display) Fail

04 CMOS Data Lost

05 FDC Fail

06 HDC Fail

07 Bad Slot

08 BIOS Problem

09 Keyboard Controller Fail

10 Cache RAM Problem

11 Memory Socket Bad

12 Hang Up Hardware

13 Hang Up Software

14 PCB Problem

15 CPU Socket Bad

16 LAN Fail

17 Audio Fail

18 Serial Port Fail

19 Parallel Port Fail

20 Others

Please specify the following when returning the RMA boards:

(1) Hardware Configuration (2) OS or Software (3) Testing Program

___________________

Authorized Signature

User's manual | ENDAT 4066i User`s manual

User’s Manual

Copyright Notice

Installation Notice

Specification:

TABLE OF CONTENTS

CHAPTER 1. INTRODUCTION ....................................................... 1

CHAPTER 2. SETTING UP THE MOTHERBOARD ....................... 5

CHAPTER 3. AWARD BIOS SETUP............................................. 18

CHPATER 4. VGA, LCD, FEATURE.............................................. 31

CHPATER 5. LAN ADAPTER ........................................................ 35

APPENDIX A: FLASH MEMORY UTILITY.................................... 39

APPENDIX B: CONNECTOR PIN ASSIGNMENT ........................ 40

APPENDIX C: UC-COM56 JUMPER SETTING............................ 41

APPENDIX D: LIMITED WARRANTY ........................................... 42

Chapter 1. Introduction

1-1. Features

Basic Feature:

Optional features:

Full Software Support:

1-2. Unpacking

Note: Please leave the motherboard in its original package until you are ready to install it!

1-3. Electrostatic Discharge Precautions

1-4. Motherboard Layout

Chapter 2. Setting up the Motherboard

2-1. Jumpers And Connectors

Please double-check the insertion and orientation of the LCD cable before applying power. Improper installation will result in permanent

damage LCD panel.

Part 1: Onboard Jumpers

Part 2: Onboard Connectors

2-2. Installing Memory

2-3. Shared VGA Memory

2-4. Installing Riser Card

2-5. Assigning IRQs for Expansion Cards

2-6. Watchdog Timer

2-7. Digital I/O

1) Pin out of digital I/O header (J13):

2) Digital input control port (48Fh):

3) Digital output control port (48Eh):

Chapter 3. AWARD BIOS SETUP

Phoenix – Award BIOS CMOS Setup Utility

3-1. Standard CMOS Features

3-2. Advanced BIOS Features

APIC Mode

MPS Version Control For OS

3-3. Advanced Chipset Features

Memory Frequency For

AGP Aperture Size (MB)

On-Chip Frame Buffer Size

Boot Display

(Optional Item)

(Optional Item)

3-4. Integrated Peripherals

Integrated Peripherals

OnChip IDE Device

IDE HDD Block Mode

IDE Primary Master/Slave PIO and IDE Secondary

Master/Slave PIO

IDE Primary Master/Slave UDMA and IDE Secondary

Master/Slave UDMA

On-Chip Serial ATA

Serial ATA Port0 Mode and Serial ATA Port1 Mode

Onboard Device

SuperIO Device

3-5. Power Management Setup

ACPI Function

ACPI Suspend Type

3-6. PnP/PCI Configurations

Reset Configuration Data

Reset Configuration Data

PCI/VGA Palette Snoop

3-7. PC Health Status

PC Health Status

3-8. Frequency / Voltage Control

Frequency/Voltage Control

Chapter 4. VGA, LCD Feature

4-2. LVDS Panel And TV Feature (optional)

LVDS Panel Interface

4-3. PCI Bus Audio Adapter Features

4-4. Driver Utility Installation Guide