Motorola | bmc9022 | User manual | UR3L-SR4 Operating Manual For Easy Clicker
Add to my manuals
2 Pages
Motorola bmc9022 is a versatile device offering a range of capabilities to enhance your home entertainment experience. With its user-friendly interface, you can effortlessly control your TV, cable box, DVD player, and audio system. The device's ability to learn commands from other remotes allows for seamless integration with your existing setup. Additionally, the programmable macro buttons provide one-touch access to your favorite channels or custom commands, making it a breeze to navigate your entertainment options.
advertisement
Operating Manual
For Easy Clicker
UR3L-SR4
Universal Remote Control, Inc.
www.universalremote.com
OCE-0082B REV 09 (02/14/12)
1
Introduction
This remote control is designed to operate most IPTV and DTA
STBs as well as Digital and
Analog Cable Boxes.
2
Replacing Batteries
Before you program or operate the remote control, you must install two new AAA alkaline batteries.
STEP1 Remove the battery compartment cover from the back of your remote control.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
4
3
Button Functions
Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the
CBL, TV, or DVD button, depending on which device you are programming the remote to operate.
STEP1 Turn on the equipment you want toprogram. To program your TV, turn on the TV.
STEP2 Point the remote at the component andpress and hold the [DEVICE] key for 4seconds until the Device LED blinks off and turns back on. Continue holding the [DEVICE] key and press the numberkeys, one at a time, starting with 1, then2, 3...0. Stop pressing the number keys when the device turns off.
STEP3 Release the [DEVICE] key to save the code. The Device
LED will blink twice to confirm the code is stored.
Repeat the steps above for all components
(CBL, TV, DVD).
B. Manual Pr ogramming
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment. The threedigit code numbers are listed in the code tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD) .
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.
If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
*Note: You can verify that you have selected the correct code by pressing the [POWER] button.
The equipment should turn back on. Then try all of the functions on the remote control
(i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from
STEP 3 above using the next three digit code number from the brand list.
STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device
LED will blink twice to confirm that the code has been stored.
C. Auto Sear ch Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds.
The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Press the [CH ] or [CH ] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the
[CH ] or [CH ] button as soon as the equipment turns off.
*Note: You can verify that you have selected the correct code by pressing the [POWER] button.
The equipment should turn back on. Then try all of the functions on the remote control
(i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from
STEP 3 above to continue the
Auto Search Method.
STEP4 Press the same [DEVICE] button to store the code. The
Device LED will blink twice to confirm that the code has been stored.
D. T o find the Thr ee-Digit Code that W as Pr ogrammed using the Auto Sear ch Method
STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds.
The device LED will turn on for
30 seconds. The next step must be performed while the
LED is on.
STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off.
Example : One blink, then three blinks, then eight blinks indicates the code number 138.
*Note : Ten blinks indicates the number 0.
E. Pr ogramming a Second
STEP1 Press the [DVD] button and the [OK/SEL] button simultaneously for 3 seconds. The DVD
LED will turn on for 30 seconds.
The next step must be performed while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD] button.
The device LED will blink twice to confirm that the code has been stored.
F . The Lear ning Method
STEP1 Press the [Device] button
(CBL, TV or DVD) to be programmed and the [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on.
STEP2 Line up the UR3L-SR4 to the other remote, head-to-head,
1 or 2 inches apart.
STEP3 Press any button on the UR3L-
SR4 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button.
STEP4 Press and hold the [MUTE] button on the other remote until the UR3L-SR4 Device LED light blinks twice.
*Note : The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and
4. Continue learning other buttons by repeating STEPS 3 and 4.
STEP5 Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and
[INPUT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly.
G. Erasing a Single Lear ned
STEP1 Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on.
STEP2 Press and hold the button you want to erase for 3 seconds.
The Device LED will blink twice to confirm the erasure.
STEP3 To exit, press and hold both the
[Device] and [INPUT] buttons simultaneously until the Device
LED blinks 3 times.
H. Erasing All Lear ned Commands fr om One Device
STEP1 Press the [DEVICE] and
[INPUT] buttons simultaneously for 3 seconds until the
Device LED light turns on.
STEP2 Press and hold both the
[DEVICE] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure.
STEP3 To exit, press and hold both the
[DEVICE] and [INPUT] buttons simultaneously until the Device
LED blinks 3 times.
I. Pr ogramming the All Of f Button
This allows you to program the All Off button so it can send up to three power
On/Off commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [All OFF] button and the
[OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.
STEP3 Press the first [Device] button you want to store in the [ALL OFF] button and then the [POWER] button. Repeat this for other
Device until you have stored all the desired power commands into the [ALL OFF] button.
STEP4 Press the [CH ] button to save the power commands you stored. The [CBL] button will blink twice to confirm the
Device have been saved.
J. Pr ogramming for
If your remote model has customprogrammable Macro buttons available, they can be programmed to act as a
‘Macro’ or Favorite Channel button in
CABLE mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed With one button press.
*Note : The FAV button is not programmable if you have a
Digital Cable Box made by
Pace, Pioneer or CISCO/SA.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and
[OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example,
007) using the Number Pad, then press the [STOP] button.
Then enter the code for the next channel (for example,
050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered.
STEP4 Press the [CH ] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands.
To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel.
To erase the Macro programming and return to the original function:
STEP1 Press the [CBL] button to select the CABLE mode.
STEP2 Press a [MACRO] button and the
[OK/SEL] button simultaneously for 3 seconds. The CBL device
LED will turn on for 30 seconds.
The next step must be performed while the LED is on.
STEP3 Press the [CH ] button to erase the functions stored in the button. The CBL device
LED will blink twice to confirm that the memory button has been erased.
K. Pr ogramming V olume Contr ol
Volume and Mute control are factoryprogrammed to automatically transfer to the respective Device mode you select, as follows:
CBL : TV TV : TV DVD : TV
If you wish to store the Cable volume control in CBL mode, use the following steps.
STEP1 Press the [OK/SEL] button and
[CBL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL ] button.
The device LED will blink.
STEP3 Press [CBL] button. The device LED will blink twice to confirm the programming.
Note : To return CBL device to TV volume repeat steps above replacing [CBL] with [TV] in
Step 3.
L. Pr ogramming Channel Contr ol
Channel controls are factory-programmed to automatically transfer to the respective
Device mode you select, as follows:
CBL : CBL TV : CBL DVD : DVD
If you wish to store the TV channel controls in TV mode, use the following steps.
STEP1 Press the [OK/SEL] button and
[TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL ] button. The device LED will blink.
STEP3 Press [TV] button. The device
LED will blink twice to confirm the programming.
Note : To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3.
M. Low Batter y W ar ning
When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment.
N. Memor y Lock System.
This remote control is designed to retain programmed memory for 10 years — even after batteries are removed from the remote control.
For additional information about your remote control, go to www.universalremote.com
2
5
6
3
4
7
8
9
5
Quick Set-up Code Tables
CBL
Quick Number Manufacturer/Brand
0
1
PACE
SCIENTIFIC ATLANTA/CISCO
PACE, SAMSUNG
MOTOROLA
AMINO
AT&T
CISCO
DIRECTV
MOXI
AMINO
MOTOROLA
TV
Quick Number
7
8
5
6
9
0
3
4
1
2
Manufacturer/Brand
SANYO
SONY
SAMSUNG
LG
TOSHIBA
PANASONIC
PHILIPS
HITACHI
SHARP
VIZIO
DVD
Quick Number
7
8
5
6
9
0
3
4
1
2
Manufacturer/Brand
HITACHI
SONY
PHILIPS
SAMSUNG
PHILIPS MAGNAVOX
PANASONIC
LG
JVC
DENON
PIONEER
6
Set-up Code Tables
CABLE TV
Manufacturer/Brand Set-Up Code Number
CISCO/SA EXPLORER Series
8600X
8600
8540,8570,8590
8500
001
007
011
021
022
023
CABLE TV
Manufacturer/Brand Set-Up Code Number
MOTOROLA DCT Series (DVR Model) 002
GENERAL DCT Series,DCH Series,
INSTRUMENT CFT2200 008
DL4,DQNV/DRX,DPBB,DPV
/DP/DQN,DRZ
JERROLD BMC9012/BMC9022
DSR470
027
006
005
012 CFT2000
DL4,DQNV/DRX,DPBB,DPV
DIGEO
/DP/DQN,DRZ
2056-MSX
DIRECTV HR20,HR21
EVOLUTION FTA X0-01
027
153
229
158
EVOLUTION
MOXI
UNIVERSAL SD DTA
MOXI MEDIA CENTER
MOXI HD DVR
2056-MSX
NFUSION NUVENIO SD PHOENIX,
NUVENIO HD,
PACE
SOLARIS, NOVA
500 Series
189
006
052
153
PIONEER
TDC Series
510
VOYAGER Series
BA9000
SAMSUNG OCAP MODELS
004
001
007
013
192
001
007
002
SKY
TELNET
SKY+HD
SKY HD
RC-RW100
001
007
230
204
154
CABLE IPTV
Manufacturer/Brand
ADB
Set-Up Code Number
5810WX
AMINO
AT&T
CISCO
A125, A130, A530
A110
U-VERSE
U-VERSE
RNG200
CIS330, CIS430
251
251
313
316
254
255
259
315
256
260
CABLE IPTV
Manufacturer/Brand
COMCAST RNG200
DREAM DM7020S, DM7025,
ENTONE
MYRIO
Set-Up Code Number
313
DM8000HD
Amulet IPTV Receiver
IPTV Receiver
159
258
254
255
MOTOROLA U-VERSE, VIP1200,
VIP1216, VIP1616T,
VIP1910, VIP1920,
NOW TV
VIP1960, VIP1970
NOW TV
PACE RNG200
SCIENTIFIC U-VERSE
ATLANTA
WEGENER IPTV Receiver 250
253
314
313
251
TV
Manufacturer/Brand Set-Up Code Number
ADMIRAL
ADVENT
AIWA
072 096 081
147
141 145
AKAI
AKIO
ALARON
AMARK
070 146 148 124 226 104 108
103
028
112
AMERICA ACTION 043
AMPRO
ANAM
AOC
APEX
073
043 054 056 080 112 131
058 070 112 616
092
APEX DIGITAL 150 037 015
AQUAVISION 097 100
AUDIOVOX 076 103 043 035 078 224
AVIELO 090
AVION 223
BAYSONIC 043
BELL&HOWELL 072
BENQ 234
BRADFORD 043
BROKSONIC 096
CANDLE 070 002 003
CAPEHART 058
CARVER 164
CELEBRITY 001
TV
Manufacturer/Brand Set-Up Code Number
CETRONIC 043
CINERAL 103 120
CITIZEN
CLASSIC
COBY
070 002 003 101 103
043
640 641
CONTEC
CRAIG
CROSLEY
CROWN
043 051
043 054 028
164
043
CURTIS MATHES 070 101 011 072 120 164 081
CXC
DAEWOO
DELL
DENON
043
076 103 112 043 120
041
011
DIGITAL PROJECTION 090
DUMONT
DWIN
DYNASTY
FISHER
073
131 132
043
007 057
ELECTROBAND 001
ELECTROHOME 024 076
ELEMENT 110 622
EMERSON 005 028 043 048 076 096 155 051
153 121
ENVISION 070
EPSON
ESA
FUJITSU
FUNAI
FUSION
087 228
031
164 197 028 149
028 043 052 168
642
FUTURETECH 043
GATEWAY 165 031
GE 070 073 008 009 034 056 074 155
120 081
GEM 031
GIBRALTER 073
GOLDSTAR 106 112
GRUNPY 028 043
HAIER 116 623
HANNSPREE 099
HARLEY DAVIDSON 028
HARMAN KARDON 164
HARVARD 043
HISENSE 198 021 619 630
TV
Manufacturer/Brand Set-Up Code Number
HITACHI 007 009 011 072 010 012 023 158
174
HP
HUMAX
027 039 098
122
HYPERION 609
HYUNDAI
ILO
INFINITY
INFOCUS
INKEL
049 067
055 096
164
046 215 225 233
129
INSIGNIA
INTEQ
JBL
JCB
068 069 078 096 164 168 604 617
073
164
001
JCPENNEY 008 024 030 070 101 156
JENSEN
JVC
013
038 001 034 083 639
KENWOOD 070 001
KLEGG 220
KLOSS 002 059
KREISEN
KTV
202
070 043
LG 106 112 086 598
LODGENET 072
LOEWE 196 164
LOGIK
LXI
072
007 052 164 015 081
MAGNAVOX 070 003 022 059 060 061 164 094
056 028 035 211 205 218 050 138
MAJESTIC 072
MARANTZ 164 070 143 169
MATSUI 164
MATSUSHITA 080
MAXENT 165
MEMOREX 007 072 028 096
MGA
MIDLAND
024 070
073
MINTEK
MINUTZ
077
008
MITSUBISHI 024 040 146 028 124 200 235 081
MOTOROLA 081
MTC 070 101
MULTITECH 043
NAD 025 015
TV
Manufacturer/Brand Set-Up Code Number
NEC
NEXUS
NIKEI
NIKKO
NIKO
NORCENT
NTC
211
103
NUVISION 084
OLEVIA 219
ONKING 043
070 040 056 007 019 024
620 078
043
103
175
ONWA
OPTIMUS
043
080
OPTOMA 029
OPTONICA 019 081
ORION 096 201 203 204 205 028
PANASONIC 034 056 080 164 190 230 248 524
607
PHILCO
PHILIPS
070 003 024 056 059 060 164
164 005 038 093 070 003 059 199
218 232
PIONEER 023 025 135 176 018 070 183 191
214
POLAROID 026 118 119 006
PORTLAND 103
PRISM 034
PROTON 058 171 163
PROTRON 102 213 115
PROVIEW
PROX
QUASAR
110
092
034 056 606
RADIO SHACK 019 043
RCA 156 070 023 024 056 074
REALISTIC
209 081
007 019
REVOLUTION HD 220
RUNCO
SAMPO
072 073 216
070 058 165
SAMSUNG 101 133 089 105 070 184 185 192
SANSEI 120
SANSUI
SANYO
SCEPTRE
SCOTT
SEARS
096
007 053 057 020
036
005 028 043 048 113
007 028 030 057 094 052 164 015
TV
Manufacturer/Brand Set-Up Code Number
SEMIVOX
SEMP
043
015
SHARP 019 028 022 081
SHERWOOD 128
SIGNATURE 072
SONY 001 608
SOUNDESIGN 003 028 043
SOYO 163
SPECTRICON 112
SQUAREVIEW 052
SSS
STARLITE
043
043
SUPRE MACY 002
SUPREME 001
SUNBRITE 633 634 635 236
SUNBRITE TV 605
SVA 046
SYLVANIA 070 003 059 060 164 056 168 121
231
SYMPHONIC 052 168
SYNTAX OLEVIA 219
TANDY
TATUNG
081
056
TECHNICS 034 080
TECHNOL ACE 028
TECHVIEW 246
TEKNIKA 002 003 024 028 043 072 101 103
TELERENT
TERA
164
072
172
THOMPSON 166
TNCI
TOSHIBA
073
030 007 040 101 142 045 137 015
TRUTECH 212
UNIVERSAL 008 009
VIDEO CONCEPTS 146
VIDIKRON 164
VIEWSONIC 210 211
VIORE 055 229
VISCO
VIZIO
WARDS
110
031 236 624 625
164 008 009 019 028 060 061 072
074 070
WESTINGHOUSE 076 036 221 222 001
WINBOOK 079
TV
Manufacturer/Brand Set-Up Code Number
YAMAHA 070
YUPITERU 043
ZENITH
ZONDA
011 072 073 095 103 096
112
DVD
Manufacturer/Brand Set-Up Code Number
ADCOM
AIWA
AKAI
203
210
239
APEX DIGITAL 240 196
ARCAM
BOSE
165 148
244 245
CAMBRIDGE AUDIO 224 145
COBY 206
CYBERHOME 170 212
DAEWOO
DENON
170
225 358 226
DURABRAND 235
EMERSON 235
ESA 235
FUNAI 235
GOLDSTAR 182 194
GO VIDEO 228 182 252 253 254
GRADIENTE 243
HARMAN KARDON 217
HITACHI 181
INSIGNIA 235 085 182 178 349
INTEGRA
JVC
236 128
185
KENWOOD 166
KISS
KLH
KOSS
237
230
243
KRELL
LEXICON
218
216
LG 182 194 105 350
MAGNAVOX 178 191 195 235
MARANTZ 135
MCINTOSH 167
MEMOREX 222
MERIDIAN 200
MINTEK 240 196
DVD
Manufacturer/Brand Set-Up Code Number
MITSUBISHI 186
MYRYAD 211
NAD 198 182 353
ONKYO
OPPO
OPTIMUS
207 236 128
125
187
ORITRON 243
PANASONIC 076 219 103 104
PHILIPS 164 191 195 209 127
PIONEER 187 221 223 354
POLAROID 085
RCA
SANSUI
SANYO
086
201
215
SAMSUNG 183 228 205 073 152 241
SENSORY SCIENCE 254
SHARP 174
SHERWOOD 129
SONY 077 168 190 213 118 119 120 121
126 351
SPECTRONIQ 088
SUPERSCAN 235
SV2000 235
SYLVANIA 235
SYMPHONIC 235
TAG McLaren 202
THETA DIGITAL 187
TOSHIBA
TRUTECH
169 191 206 227 201 236 356
151
VENTURER 229
VINC
YAMAHA
ZENITH
220 087
199 204 246
182 194
DVR(TIVO)
Manufacturer/Brand Set-Up Code Number
CHANNEL MASTER 841
DIRECTV 819
DSTV 786 787 788 241 800
HUGHES
HUMAX
817
817
ICREALTIME 111
MOXI 112
DVR(TIVO)
Manufacturer/Brand Set-Up Code Number
PHILIPS
RCA
790 817 785
809
REPLAY NETWORKS 775
SONY
TIVO
TOSHIBA
804 805
790 817
817
VCR
Manufacturer/Brand Set-Up Code Number
ADVENTURA 534
AIWA 534
AKAI 543
ANAM 645
AUDIO DYNAMICS 512 543
AUDIOVOX 601
BROOKSONIC 629
CALIX 601
CANON
CITIZEN
645
601
CRAIG 503 602
CURTIS MATHES 645
DAEWOO 612
DBX 512 543
DYNATECH 534
ELECTROHOME 559
ELECTROPHONIC 601
EMERSON 506 645 534 601 629 631 653
FISHER 503 508
FUNAI 534
GARRARD 534
GE 645 647 644
GO VIDEO 602
GOLDSTAR 601 513 512 623
GRADIENTE 534
HARLEY DAVIDSON 534
HARMAN KARDON 512
HITACHI 534 543 513
HQ 534
INSTANTREPLAY 645
JCL 645
JCPENNEY 512 513 602 601
JENSEN 543
JVC 548 543 512 645
KEC 601
VCR
Manufacturer/Brand Set-Up Code Number
KENWOOD 548 534
KODAK 645 601
LG 601 513 512 623
LLOYD 534
LXI 534 503
MAGIN 602
MAGNAVOX 567 645 534
MARANTZ 567 512 645
MARTA 601
MATSUSHITA 645
MEI 645
MEMOREX 601 503 645 534 602
MINOLTA 513
MITSUBISHI 559 513
MOTOROLA 645
MTC 534 602
MULTITECH 534
NEC 512 543 548
NIKKO 601
NORDMENDE 543
OPTIMUS 601
PANASONIC 570 645 667
PENTAX 513 645
PHILCO 645 534 567
PHILIPS 645 567 534 601
PILOT 601
PIONEER 513 548
RADIO SHACK 623
RADIX
RANDEX
601
601
RCA 644 647 645 513 534 602
REALISTIC 503 508 645 534 602 601
RICO 558
SAMSUNG 602 612 644 647
SANSUI 543 548
SANYO 503 602
SCOTT 612 629 631
SEARS 503 508 513 601 612
SHARP 649 645
SIGNATURE 534
SONY 557 558 503 645 649 654
SOUNDESIGN 534
STS 513
SYLVANIA 645 534 559 567
VCR
Manufacturer/Brand Set-Up Code Number
SYMPHONIC 534
TANDY 534
TATUNG 543
TEAC 534 543
TECHNICS 645 570
TEKNIKA 645 534 601
THOMAS 534
TMK 506
TOSHIBA 612 631 508 559 513
TOTEVISION 602 601
UNITECH 602
VECTOR RESEARCH 512
VICTOR 548
VIDEO CONCEPTS 512 534
VIDEOSONIC 602
VILLAIN 534
WARDS
XR-1000
503 513 645 534 602 631
645 534
YAMAHA 512 534 543
ZENITH 548 601 534 558
TV/VCR Combos
Manufacturer/Brand Set-Up Code Number
EMERSON 653
FUNAI 534
GOLDSTAR 601 623
HARLEY DAVIDSON 534
HITACHI 534
JCPENNEY 601
LG 601 623
LLOYD 534
MAGNAVOX 534 567
MEMOREX 601
PANASONIC 570 667
PHILIPS 534 567 645
RADIO SHACK 623
RCA 534 644
SAMSUNG 602
SEARS 601
SONY 557 654 558
SYLVANIA 567
SYMPHONIC 534
THOMAS 534
ZENITH 534
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project