Mega Lite N-E Color Strip User manual

USER MANUAL
Table of Contents
Safety Information……………………………………………………………………………………………. 3
Specifications……………………………………………………………………………………………………..4
Main Power Connection…………………………………………………………………………………..5
DMX-512 Connection…………………………………………………………………...……………...... 5
DMX Profile......................................................................................................................... 6
Main Control Menu...........................................................................................................9
Rigging the Fixture………………………………………………………………………………………….11
Cleaning & Maintenance.............................................................................................11
Parts List............................................................................................................................ 11
Protection Against Fire
1.
3.
4.
5.
6.
Maintain a minimum of 1 foot distance from any type of flame.
Replace fuse only with the specified type and rating.
Do Not install the unit to close to a heat source.
Make sure cable are properly secured away from unit movement.
Maximum surface operating temperature 80º.
Protection Against Fire
1.
2.
3.
4.
Disconnect power before servicing.
For connection to main power supply proceed to page 5.
This unit must be earthed. (electronically grounded)
Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3
Fixture
4054– N-E Color Pro Strip
Mechanical Specifications
DMX Connectors:
3-pin XLR connectors
Power Connection:
In/Out
Thermal:
Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Fastening System:
Center Mounting Yoke (optional end mounts)
Display:
Digital
Refresh Rate:
400Hz (flicker free)
Fixture
40.25 ”
3.5
Packaged for Shipping
Size: 40.25”L x 6.75”W x 3.5”H
Size: 41”L x 4.75”W x 7.25”H
Weight: 10 lbs
Weight: 12 lbs
2.75
Electrical Specifications
LED Quantity:
Red:
Green:
Blue:
264
96
72
96
LED Diameter: 10 mm
Segments: 8
LED Lifetime: 60,000 to 100,000 hours
LED Angle: 35° ( ± 5º )
Power Consumption: 100 - 240V 50/60 Hz
Ballast: Electronic
Watts:
Amps:
27
.36
Control & Programming
Protocol: DMX 512
DMX Channels:
Mode P
Mode A
Mode F
Mode H
Mode L
12 DMX Channels
16 DMX Channels
6 DMX Channels
24 DMX Channels
40 DMX Channels
R,G,B,R,G,B,R,G,B,R,G,B
R,G,B, Dim/Str, R,G,B, Dim/Str, R,G,B, Dim/Str, R,G,B, Dim/Str
Dimmer, R,G,B Strobe, Macros
R,G,B,R,G,B,R,G,B,R,G,B,R,G,B,R,G,B,R,G,B,R,G,B
R,G,B, Dim,Str, R,G,B, Dim,Str, R,G,B, Dim,Str, R,G,B, Dim,Str
R,G,B, Dim,Str, R,G,B, Dim,Str, R,G,B, Dim,Str, R,G,B, Dim,Str
Control options: Audio-trigger
Operating Mode: Master/Slave, Stand alone
4
4”
Main Power Connection
Caution!
1.
2.
3.
4.
Do not connect fixture to a dimmer system.
This unit has Auto switching power supply. It will respond to 110V or 220V automatically
This unit must be earthed. (electronically grounded)
Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to 60Hz
Cable (USA)
Cable (EU)
Pin
110V
220V
Black
Brown
Live
L
L
White
Light Blue
Neutral
N
L
Green
Yellow/Green
Ground
110V—Connection
220V—Connection
N
L
L
L
DMX-512 Connection
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded
twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or
the fixture with another.
DMX—output
DMX—input
1. Shield
2. Signal (-)
2
1
2
1
3. Signal (+)
3
3
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120
Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the
last fixture on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (HOS-DMXT).
5
N-E Color Pro Strip Mode A (16 Channel)
DMX Chanel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Function
LED Color
LED Color
LED Color
Dimmer
LED Color
LED Color
LED Color
Dimmer
LED Color
LED Color
LED Color
Dimmer
LED Color
LED Color
LED Color
Dimmer
Description
RED LED intensity
Green LED intensity
Blue LED intensity
Dimmer Segment 1
RED LED intensity
Green LED intensity
Blue LED intensity
Dimmer Segment 2
RED LED intensity
Green LED intensity
Blue LED intensity
Dimmer Segment 3
RED LED intensity
Green LED intensity
Blue LED intensity
Dimmer Segment 4
Value
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
N-E Color Pro Strip Mode P (12 Channel)
DMX Chanel
1
2
3
4
5
6
7
8
9
10
11
12
Function
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
LED Color
Description
Red LED intensity Segment 1
Green LED Intensity Segment 1
Blue LED Intensity Segment 1
Red LED intensity Segment 1
Green LED Intensity Segment 1
Blue LED Intensity Segment 1
Red LED intensity Segment 1
Green LED Intensity Segment 1
Blue LED Intensity Segment 1
Red LED intensity Segment 1
Green LED Intensity Segment 1
Blue LED Intensity Segment 1
6
Value
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
N-E Color Pro Strip Mode F ( 6 Channel )
DMX Chanel
1
2
3
4
Function
Dimmer
LED Color
LED Color
LED Color
5
Strobe
6
Macro
Description
Master Dimmer
Red LED intensity
Green LED Intensity
Blue LED Intensity
No Function
Strobe (slow to fast)
Value
0-152
153-242
243-255
0-255
0-9
10-57
No Function
Pulse On to Off (slow to fast)
No Function
Pulse Off to On (slow to fast)
No Function
Random Strobe
No Function
Color Fade (slow to fast)
Color Fade RGB (slow to fast)
Color Fade Chase
Color Snap
Color Pulse
Random Macro
58-59
60-108
109-110
111-159
160-161
162-255
0-9
10-50
51-91
92-132
133-173
174-214
215-255
N-E Color Pro Strip Mode H (24 Channel)
DMX Chanel
1
2
3
""
22
23
24
Function
LED Color
LED Color
LED Color
""
LED Color
LED Color
LED Color
Description
Red LED intensity
Green LED Intensity
Blue LED Intensity
""
Red LED intensity
Green LED Intensity
Blue LED Intensity
7
Value
0-255
0-255
0-255
""
0-255
0-255
0-255
N-E Color Pro Strip Mode L (40 Channel)
DMX Chanel
1
2
3
4
Function
LED Color
LED Color
LED Color
Strobe
5
""
36
37
38
39
Dimmer
""
LED Color
LED Color
LED Color
Strobe
40
Dimmer
Description
Red LED intensity
Green LED Intensity
Blue LED Intensity
Strobe (slow to fast)
Random (slow to fast)
Dimmer
""
Red LED intensity
Green LED Intensity
Blue LED Intensity
Strobe (slow to fast)
Random (slow to fast)
Dimmer
8
Value
0-255
0-255
0-255
0-152
153-255
0-255
""
0-255
0-255
0-255
0-152
153-255
0-255
Main Control Menu
CONTROL BOARD
The control board on the fixture base is your interface to access and control
all the functions on the unit. Its digital display gives you a code view of the
options and functions. The following will explain each function and its options.
Menu
DMX Address
Red Dimmer
Green Dimmer
Blue Dimmer
1-512
0-15
0-15
0-15
Flash
0-15
Fade Scroll
0-15
Flash Scroll
Chase Effect
0-15
0-15
Chase Speed
0-15
Up
Down
Sound Chase
Loop
Enter
Sound Flash
Sound Sensor
Loop
0-15
Mode A (16 Channels) R,G,B, Dim/Str, R,G,B, Dim/Str,
R,G,B, Dim/Str, R,G,B, Dim/Str
DMX Address
Mode P (12Channels) R,G,B,R,G,B,R,G,B,R,G,B
Press Enter to select the mode of operation.
Mode F (6 Channels) Dimmer, R,G,B Strobe, Macros
Mode H (24 Channels)
R,G,B,R,G,B,R,G,B,R,G,B,R,G,B,R,G,B,R,G,B,R,G,B
Use the up/down keys to select the required DMX start channel.
Mode L (40 Channels) R,G,B, Dim,Str, R,G,B, Dim,Str,
R,G,B, Dim,Str, R,G,B, Dim,Str
Red Dimmer
This function allows you to dim the red LED’s on the whole strip. Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings.
Green Dimmer
This function allows you to dim the green LED’s on the whole strip. Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings.
Blue Dimmer
This function allows you to dim the blue LED’s on the whole strip. Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings.
Flash
This function allows you to strobe the LED’s on the whole strip in White color. Press Enter use the up/down keys to select desired flash settings. Press Enter to confirm the settings.
9
Fade Scroll
This function allows you to fade the LED’s on the whole strip from one color to another. Press Enter use the up/down keys to
select desired fade speed settings. Press Enter to confirm the settings.
Flash Scroll
This function allows you to change the LED’s on the whole strip from one color to another. Press Enter use the up/down keys to
select desired color change speed settings. Press Enter to confirm the settings.
Chase Effect
This function allows you to select different chase patterns on the whole strip. Press Enter use the up/down keys to select desired chase settings. Press Enter to confirm the settings.
Chase Speed
This function allows you to select the speed of the chase that was selected on the Chase function . Press Enter use the up/down
keys to select desired chase speed settings. Press Enter to confirm the settings.
Sound Chase
This function allows you to select the chase pattern that will be triggered via audio. Press Enter use the up/down keys to select
desired Chase settings. Press Enter to confirm the settings.
Sound Flash
This function allows you to select the flash pattern that will triggered via audio. Press Enter use the up/down keys to select desired dimmer settings. Press Enter to confirm the settings.
Sound Sensor
This function allows you to select the sensitivity of the audio sensor. Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings.
!
Rigging the fixture
Caution!
The installations must be carried out by an authorized dealer or trained professional.
Unit may cause severe injures if you have doubts concerning the safety do not install.
Unit is to be 24inches away from flammable materials (decoration material)
Use high quality installation equipment to hang unit.
1.
2.
3.
4.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to
be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least
one time a year by a skilled person.
"
#
$
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further
instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems
have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to be carried
out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or
trained professional only.
Should you have further questions , please contact your dealer.
Parts List
9057
6 Unit Road Case
4050-gc
Plastic Cover
4054-pcb
Main PCB card
4000-dmx
XLR connection
4050-nps
Power Supply
4000-dis
Display
4000-fh
Fuse Holder
4050-EC
End Cap
4054-LEDM
LED Module
11
Warranty Information
Limited Warranty
Unless otherwise stated, your product is covered by a one year parts and labor limited warranty. Dichroic filters and glass gobos are not guaranteed
against breakage or scratches to coating. It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and dealer
or distributor. If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
Returning an Item Under Warranty for Repair
It is necessary to obtain a Return Material Authorization (RMA) number from your dealer or point of purchase BEFORE any units are returned for
repair. The manufacturer will make the final determination as to whether or not the unit is covered by warranty. Lamps are covered by the lamp
manufacturer’s warranty.
Any Product unit or parts returned to MEGA Systems Inc. must be packaged in a suitable manner to ensure the protection of such Product unit or
parts, and such package shall be clearly and prominently marked to indicate that the package contains returned Product units or parts and with an
RMA number. Accompany all returned Product units or parts with a written explanation of the alleged problem or malfunction. Ship returned Product units or parts to: 5711 Kenwick St. San Antonio TX 78254 USA.
Note: Freight Damage Claims are invalid for fixtures shipped in non-factory boxes and packing materials.
Freight
All shipping will be paid by the purchaser. Items under warranty shall have return shipping paid by the manufacturer only in the Continental United
States. Under no circumstances will freight collect shipments be accepted. Prepaid shipping does not include rush expediting such as air freight. Air
freight can be sent customer collect in the Continental United States.
REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
MEGA SYSTEMS INC. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO ANY PRODUCT, AND MEGA SYSTEMS SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MEGA
SYSTEMS SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS, SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY PRODUCT DEFECTS OR THE PARTIAL
OR TOTAL FAILURE OF ANY PRODUCT REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN.
Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax 210-855-6279
www.mega-lite.com / [email protected]