RedMax HBZ2600 Operator Manual

848-L08-93A1 (501)

OWNER / OPERATOR MANUAL

HANDHELD BLOWER

HBZ2600

WARNING

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

Thank you for purchasing a RedMax product.

Before using our blower, please read this manual carefully to understand the proper use of your unit.

APPLICABLE SERIAL NUMBERS :

DRIVE UNIT 200101 and up ENGINE UNIT 50200101 and up

Read this manual carefully to understand all safety precautions, controls, proper operation and maintenance of your RedMax blower.

Failure to do so could result in serious injury.

SAFETY FIRST

Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.

Note that there may be times when warning seals peel off or become soiled and impossible to read. If this happens, you should contact the dealer from which you purchased the product to order new seals and affix the new seal(s) in the required location(s).

■ Notes on types of warnings

WARNING

Instructions labeled as shown at left concern critical steps or procedures which must be followed in order to prevent accidents which could lead to serious bodily injury or death. This mark is used to indicate instructions which must be followed without exception.

IMPORTANT

Instructions labeled as shown at left concern steps or procedures which, if not followed correctly, could lead to mechanical failure, breakdown, or damage.

NOTE

Used to label supplementary instructions designed to provide hints or directions useful in the use of the product.

CONTENTS

SAFETY PRECAUTIONS················································································ 4

OPERATOR

USE OF BLOWER

WORKING CONDITION

AVOID NOISE PROBLEM

AVOID CHANCES OF DAMAGE

SYMBOLS ON THE MACHINE ······································································· 7

PARTS LOCATION & SPECIFICATIONS ······················································· 8

ASSEMBLY······································································································ 8

BLOWER PIPE

FUEL················································································································ 9

HOW TO MIX FUEL

FUELING THE UNIT

OPERATION ·································································································· 11

STARTING ENGINE

RESTARTING ENGINE WHILE ENGINE HOT

STOPPING ENGINE

ADJUSTING IDLE SPEED

MAINTENANCE····························································································· 12

MAINTENANCE CHART

AIR CLEANER

FUEL FILTER

SPARK PLUG

MUFFLER

SPARK ARRESTER

AIR INLET SCREEN

HOW TO INSTALL THE AIR INLET SCREEN TO THE VOLUTE COVER

STORAGE ····································································································· 14

OPTIONAL VACUUM KIT USAGE ······························································· 15

MOUNTING THE DUST-COLLECTING KIT

DUST COLLECTING OPERATION

TROUBLESHOOTING GUIDE ······································································ 16

PARTS LIST ·································································································· 17

Safety Precautions

• Read this Blower Owner/Operator

Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury.

• Wear a face mask to guard against the inhalation of dust.

• Wear rubber-soled shoes or shoes with some other form of anti-slip protection to help protect you against falling.

• Be sure to wear proper work clothing.

■ USE OF BLOWER

• Each time before starting the engine, inspect the entire unit to see if every part is in good order and is securely tightened in place. If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been repaired.

• Be sure to keep this manual handy so that you may refer to it later whenever any questions arise. Also note that you are requested to contact the dealer from whom you purchased the product for assistance the event that you have any questions which cannot be answered herein.

• Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

■ OPERATOR

• Refrain from operating the blower if you are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication.

• Always wear eye protection goggles.

• Always wear ear protectors to protect your ears from engine noise. If this guideline is not followed, hearing loss can occur.

 4 

Safety Precautions

WARNING

• Never use the blower without the screen at the air intake of the blower.

Before each use, check that, the screw(1) is securely tightened and is free from any damage.

described in this manual should be performed by competent service personnel. Improper service to the blower fan and muffler could cause a hazardous failure.

■ WORKING CONDITION

WARNING

• Keep open flames and sparks away from the area where fuel is handled or stored, as the fuel is highly flammable.

WARNING

• Never remove debris from the intake screen while the engine is running.

Contact with rotating blower fan may result in a serious personal injury.

• Do not allow children to use blower. Make sure that each person you authorize to operate the blower understands all of the safety rules in this manual.

• Avoid using any accessory or attachment other than those bearing the RedMax mark for use with the blower.

• When suspending a job or inspecting the blower, be sure to stop engine.

• Drain the fuel from the fuel tank before transporting or storing the blower.

• When storing the blower, choose a space indoors free from moisture and out of the reach of children.

• Examine the blower at intervals for loose fasteners and rusted or damaged parts.

Use special care around the fuel line, the muffler, and the ignition wiring.

• All engine service except for those

• Make sure that the engine has cooled down before refueling.

• Mix and store fuel only in a approved container.

• Never smoke while refueling the blower.

• Wipe off any spilled fuel and tighten the fuel cap securely.

• Move at least 3m(10ft) away from the fueling spot before starting the engine.

• Check the work area that the blower will be used in and remove or cover all valuables that may be damaged by the air blast or thrown debris.

• Avoid running the engine indoors. The exhaust gases contain harmful carbon monoxide.

5 

Safety Precautions

• Keep operation area clear of all persons, particularly small children and pets. Injury may result from flying debris.

• Avoid using the blower where stable footing and balance are not assured.

• Never touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an electrical shock.

• Never touch the muffler, spark plug, or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. These metallic parts reach high temperatures during operation and doing so could result in serious burns.

■ AVOID NOISE PROBLEM

NOTE

Check and follow the local regulations as to sound level and hours of operations for blower.

• In general, operate blowers between

8a.m.and 5p.m.on week day and 9a.m.to

5p.m.weekends. Avoid using blower late at night and/or early in the morning.

• Loosen compacted leaves, grass or debris with a rake or broom beforehand, so that the lowest possible throttle setting would get the job done.

• In dusty conditions, slightly dampen surfaces.

• Check if the air filter, air intakes and muffler are working in properly.

• Never use more than one unit of the blower at one time.

■ AVOID CHANCES OF DAMAGE

• Avoid directing the blower nozzle toward persons, pets, cars, windows or anything that could be harmed by blowing debris or dust.

• Keep the nozzle at full extension when operating so as to make the air stream close to the ground.

• Collect any trash and leaves and put them into a proper container after the job is done.

• Always check to be sure that no debris has been blown onto someone else’s property.

6 

Symbols on the machine

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position: FUEL TANK CAP

(b) The direction to close the choke

Position: AIR CLEANER BODY

(c) The direction to open the choke

Position: AIR CLEANER BODY

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2

EMISSION REGULATIONS FOR SI SORE’s.

COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 5KZXS. 0254QR ; EM

ENGINE DISPLACEMENT : 25cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

KOMATSU ZENOAH CO. MADE IN JAPAN

Use RedMax 50:1 Oil !

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

CE MOTEUR EST CONFORME AUX REGLEMENTATIONS

D’EMISSIONS EPA PH2 DES ETATS-UNIS POUR LA PERIODE

DE CONFORMITE DE SI SORE : CATEGORIE A

TYPE DE MOTEUR : 5KZXS. 0254QR ; EM

CYLINDREE DU MOTEUR : 25cc

SE REPORTER AU MODE D’EMPLOI POUR LES CARACTE-

RISTIQUES DE LA MAINTENANCE ET LES REGLAGES.

KOMATSU ZENOAH CO. MADE IN JAPAN

Use RedMax 50:1 Oil !

7 

Parts Location & Specifications

MODEL HBZ2600

Dimensions ( L x W x H )

Dry Weight

(without tube and nozzle)

Fuel Tank Capacity

Engine Type

Piston Displacement

Durability Period

Carburetor

Ignition System

Spark Plug

Muffler

Operating Engine Speed

Idle Speed

Max. Air Volume

Max. Air Velocity

Noise Level (ANSI B175.2-2000)

Assembly

■ BLOWER PIPE

• Align groove in blower pipe with projection on blower housing (or another blower pipe) and slide the pipe onto the blower housing

(or another blower pipe).

Rotate the pipe clockwise to lock it into place.

8  mm ( in ) kg ( ibs ) liter ( fl. oz ) cm 3 ( cu. in ) rpm rpm cu. m/min ( cfm ) m/sec ( mph ) db ( A )

327 x 268 x 360 (12.9 x 10.5 x 14.2)

3.8 (8.4)

0.65 (22.0)

Air cooled 2-cycle gasoline engine

25.4 (1.60)

300h

Walbro Diaphragm type

CDI

NGK CMR7A

Spark arrester equipped

2.800 ~ 7.890

2.800

10.4 (367)

70 (157)

69

Fuel

WARNING

• Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least

3m (10ft) away from the fueling point before starting the engine.

• The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled

2-cycle engine use. (JASO FC GRADE

OIL or ISO EGC GRADE)

• Do not use BIA or TCW (2-stroke watercooling type) mixed oil.

■ RECOMMENDED MIXING RATIO

GASOLINE 50:OIL 1

50:1 MIXING CHART

GASOLINE gal.

1 2 3 4 5

2-CYCLE OIL fl.oz 2.6

5.2

7.8 10.4

13

GASOLINE liter 1 2 3 4 5

2-CYCLE OIL ml 20 40 60 80 100

• Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

• These engines are certified to operate on unleaded gasoline.

• Make sure to use gasoline with a minimum octane number of 89 RON

(USA/Canada: 87AL)

• If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

• Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

• Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

■ HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1. Measure out the quantities of gasoline and oil to be mixed.

2. Put some of the gasoline into a clean, approved fuel container.

3. Pour in all of the oil and agitate well.

4. Pour In the rest of gasoline and agitate

9 

Fuel

again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

5. Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6. Indicate the contents on outside of container for easy identification.

■ FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the cap on a dustless place.

2. Put fuel into the fuel tank to 80% of the full capacity.

3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1. Select bare ground for fueling.

2. Move at least 10feet (3meters) away from the fueling point before starting the engine.

3. Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;

1. FUEL WITH NO OIL(RAW GASOLINE) –

It will cause severe damage to the internal engine parts very quickly.

2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4. Mixed fuels which have been left unused for a period of one month or

more may clog the carburetor and result in the engine failing to operate properly.

10 

5. In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6. In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.

NOTE

As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty.

Also, be careful that, if the usage in the instruction manual is not observed as to the mixed gasoline, etc. described therein, it may not be covered by the warranty.

Operation

■ STARTING ENGINE

1. Rest the unit on a flat, firm place.

2. Pump the primer until fuel flows out in the clear tube.

■ RESTARTING ENGINE WHILE ENGINE IS HOT

1. When restarting the engine immediately after stopping it, leave the choke open.

2. If the engine won't start after several attempts, close the choke and repeat pulling the rope or remove the spark plug and dry it.

■ STOPPING ENGINE

Move the throttle lever to the idling position and press the stop switch (red button) until the engine comes to a complete stop.

3. Move the choke lever upward to close the choke.

4. Holding the blower handle, pull the starter rope with your right hand. (Throttle lever in idling position.)

NOTE

Except for an emergency, avoid stopping the engine while pulling the throttle lever.

■ ADJUSTING IDLE SPEED

1. When the engine tends to stop frequently at an idle mode, turn the adjusting screw clockwise.

NOTE

Avoid pulling the rope to its dead end or returning it by releasing the knob. Such actions can cause starter failures.

5. When the engine has started, move the choke lever gradually downward to open the choke.

6. Allow the engine to warm up for a half minute before starting operation.

NOTE

Warm up the engine before adjusting the idle speed.

11 

Maintenance

Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.

■ MAINTENANCE CHART system/compornent procedure fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug wipe out inspect/clean see

■ADJUSTING

IDLING SPEED (p.11) clean and readjust plug gap cylinder fins, intake air cooling vent clean muffler, spark arrester, cylinder exhaust port clean throttle lever, ignition switch screws/nuts/bolts check operation tighten/replace every every every

25 50 100 before hours hours hours note use after after after

✔

✔ ✔ replace, if necessary

✔ replace carburetor if necessary

✔

GAP: .025in(0.6~0.7mm) replace, if necessary

✔

✔

✔

✔ ✔ not adjusting screws

WARNING

• Make sure that the engine has stopped and is cool before performing any service to the blower. Contact with rotating blower fan or hot muffler may result in a personal injury.

■ AIR CLEANER

• Check the air cleaner every 25 hours of use or more frequently if used under dusty conditions. A clogged air filter may increase fuel consumption while cutting down the engine power. Never operate the blower without the air filter or with a deformed filter element because unfiltered dusty air will quickly ruin the engine.

CLEANING AIR FILTER:

1. Remove the air cleaner cover by pulling the tab on bottom and take out the filter element.

2. Use neutral detergent and warm water to clean the filter element. After cleaning, air dry the element completely. Place the filter element into the air cleaner housing and press the cover against the housing until it clicks. Never forget to attach the screen. If the screen is not attached, the cleaner will not seal properly and the dusts come into the cylinder.

12 

Maintenance

■ FUEL FILTER

• A clogged fuel filter may cause poor acceleration of the engine. Check periodically to see if the filter is clogged with dirt. The filter can be taken out of the fueling port using a small wire hook.

Disconnect the filter assembly from the fuel pipe and unhook the retainer to disassemble it. Clean the components with gasoline.

■ SPARK PLUG

• The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to

.025in.(0.6~0.7mm).

• Plug manufacturers recommend replacing the plug twice a year to avoid unexpected plug failure in a job.

REPLACEMENT PLUG IS A NGK CMR7A.

IMPORTANT

• Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.

• To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench.

■ MUFFLER

WARNING

• Inspect periodically the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, do not use the blower and have it repaired immediately.

• Note that failing to do so may result in the engine catching on fire.

IMPORTANT

• Before starting operation, always make sure to check if the muffler is properly held by two bolts to the cylinder. (Fastening

Torque : 70~110kg·cm)

• Even if one bolt out of three bolts is loose, the muffler may get loose during operation which may result in engine catching on fire.

■ SPARK ARRESTER

• The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet.

Periodically inspect and clean as necessary with a wire brush. In the State of California it is required by law (Section

4442 of the California Public Resources

Code) to equip a spark arrester when a gas powered tool is used in any forest covered, brush covered, or grass covered unimproved land.

13 

Maintenance

■ AIR INLET SCREEN

IMPORTANT

• Blowing air is taken in from the air inlet screen. When air flow has dropped down during operation, stop the engine and inspect the air inlet screen for blocking by obstacles.

• Note that failure to remove any such obstacles may result in the engine becoming overheated and damaged.

WARNING

• Never use the blower without the screen at the air intake of the blower.

Before each use, check that, the screw(1) is securely tightened and is free from any damage.

■ PROCEDURES TO BE PERFORMED

AFTER EVERY 100 HOURS OF USE

• Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time.

• Tighten all screws, bolts, and fittings.

Storage

BEFORE STORING THE BLOWER:

1. Drain a fuel tank and push the primer bulb until it becomes empty of fuel.

2. Remove the spark plug and drop a spoonful of 2-cycle oil into the cylider.

Crank the engine several time and install the spark plug.

14 

Optional vacuum kit usage (Preparing for use)

Attach the adequate accessories, respectively for blower operation and dust-collecting operation.

NOTE

• Use the gloves during operation.

• In adjustment of the blower/dust collector or in other types of operation, be sure to stop the engine and detach the spark plug cap.

• Never start operation unless this machine is completely assembled.

■ MOUNTING THE DUST-COLLECTING KIT

1)

1. Fit the extension pipe (1) groove with main unit port projection, turn to mount the pipe to the main unit.

2. Tighten the clamp screw (2) securely.

2) Installing Vacuum pipe (nozzle)

1. Loosen the screw (3), and open the suction port cover.

2. Align the (5) indicated on the vacuum pipe (4) with the indicated on the blower.

Then insert the vacuum pipe (4) into the blower.

3. Turn the vacuum pipe (4) until the (5) is aligned with the indicated on the blower to lock the vacuum pipe.

IMPORTANT

Hold the bottom of the vacuum pipe when turning the vacuum pipe to install or remove it.

3) Installing Elbow and Dust Bag

1. Open the fastener of the dust bag.

2. Insert the elbow convex groove into the dust bag elbow opening.

Continue to push the elbow convex groove until the convex hits against the dust bag opening.

Close the dust bag fastener.

3. Fit the elbow groove with discharge port projection, turn the elbow and mount the dust bag to the main unit.

15 

Optional vacuum kit usage (Tips for operation)

■ DUST COLLECTING OPERATION

• Put the dust bag belt on the shoulder, and adjust the length of the belt so as to permit easy operation.

• Confirm that the dust bag is not twisted, pull the throttle trigger, and start dust collecting operation.

• Detach the dust bag from the main unit when it is full of dust, open the dust bag fastener, and dispose of dust.

WARNING

Never suck in any liquid or lit cigarette.

• It will lead to an electric shock or burn.

NOTE

• Never suck in large wood chips, metal, glass, small stones or other foreign materials.

• A filled dust bag will lessen dust-collecting capacity. It is advisable to discharge dust before it becomes too much.

(A) Indicates Warning, Danger, and Caution.

(B) Keep work area clear of other per-sons and pets.

(C) Risk of long hair being drawn into air inlet.

(D) Wear head, eye, and hearing protection when operating this equipment.

(E) Do not run unit while vacuum door is unsecured.

Troubleshooting guide

Case 1. Starting failure

CHECK PROBABLE CAUSES ACTION fuel tank fuel filter

➞ incorrect fuel

➞ fuel filter is clogged

➞ drain it and with correct fuel

➞ clean carburetor adjustment screw

➞ out of normal range sparking (no spark)

➞ adjust to normal range

➞ spark plug is fouled/wet

➞ clean/dry spark plug

➞ plug gap is incorrect

➞ disconnected

➞ correct (GAP: 0.6~0.7mm)

➞ retighten

Case 2. Engine starts but does not keep running/Hard re-starting.

CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel or staled fuel ➞ drain it and with correct fuel carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range muffler,cylinder (exhaust port) ➞ carbon is built-up air cleaner ➞ clogged with dust

➞ wipe away

➞ wash

When your unit seems to need further service, please consult with our RedMax service shop in your area.

16 

Parts List

HANDHELD BLOWER

HBZ2600

NOTE :

1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement.

2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.

3. When placing parts orders for repair and/or replacement, check if the model name and the serial number are applicable to those specified in the parts list, then use parts number described in the parts list.

4. The contents described in the parts list may change due to improvement.

5. The parts for the machine shall be supplied seven (7) years after the machine is discontinued. [It is possible that some specific parts may be subject to change of their delivery term and list price within the limit of seven (7) years after the machine is discontinued. It is also possible that some parts may be available even after the limit of seven (7) years.]

Jan. 2005

APPLICABLE SERIAL NUMBERS :

DRIVE UNIT 200101 and up ENGINE UNIT 50200101 and up

17 

Parts List

Fig.1 ENGINE GROUP HBZ2600

18 

Fig.1 ENGINE GROUP HBZ2600

Key# Part Number Description

1 848-F30-12A2 CYLINDER

2 4810-12210 GASKET

3

4

4820-12130

4810-13162

BOLT TORX, M5x22

INSULATOR

5 T1512-13120 GASKET, INSU

6 4810-13130 GASKET, CARB

7 4820-13180 BOLT TORX, M5x20

8 848-F30-1602 REEDVALVE ASSY(S)

10

11

12

13

4810-16120

4810-16130

4810-16170

4810-16150

• REEDVALVE

• STOPPER

• SCREW, M3x8

PIPE, AIR S

14 848-F30-1612 REEDVALVE ASSY(F)

20

21

22

23

16

17

18

19

4810-16120 • REEDVALVE

4810-16130 • STOPPER

4810-16170 • SCREW, M3x8

4810-16160 PIPE, AIR F

4810-16140 GASKET, VALVE

4820-16310 BOLT TORX, M4x10

4810-21101 CRANKCASE COMP.

2629-21130 • PIN

24 4810-21140 GASKET, CASE

25 06030-06001 BEARING

26

27

4810-21210

1850-21220

SEAL

SEAL

28 04065-02812 SNAPRING

29 4820-21310 BOLT TORX, M5x30

30

31

4810-41110

5910-41210

PISTON

RING

36

37

38

39

32 T1513-41310 PIN

33 1260-41320 SNAPRING

34

35

5500-41410

1101-41340

BEARING

WASHER

4810-42000

1000-43240

5516-43230

4810-71110

CRANKSHAFT COMP.

KEY

EXTENTION

ROTOR

40 T1513-71200 COIL ASSY

41 T1513-71220 • CORD

42

43

2616-71320

1260-71261

• CAP

SPACER

44 4820-72150 BOLT TORX

45 848-F3C-8102

2

CARBURETOR ASSY, WYA-26 1

46 T1551-06030 • REBUILD KIT

47 T1551-81450 •• BODY ASSY

– ••• SCREEN

– ••• VALVE

53

– ••• SPRING

– ••• PIN

– ••• LEVER

4810-06021 •• GASKET KIT

59

60

– ••• DIAPHRAGM 1

– ••• GASKET, diaphragm 1

– ••• DIAPHRAGM, pump

– ••• GASKET, pump

1

1

– ••• RING

1850-81490 • BODY, purge

1850-81520 • COVER, pump

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

1

2

1

1

1

2

1

3

1

2

1

2

1

1

2

6

1

3

1

1

1

1

1

1

1

1

1

Q'ty

1

1

2

1

1

1

2

1

Key# Part Number Description

65

66

67

68

61

62

63

64

1751-81510 • PUMP, priming

4810-81250 • JET, #38.5

1751-81240 • O-RING

1751-81130 • RING

1881-81140 • SWIVEL

1752-81110 • SCREW

5500-81120 • BRACKET

1751-81180 • NUT, adjuster

69

70

71

72

1918-81170

1850-81530

5500-81160

4820-82310

• SCREW, adjuster

• SCREW

• WASHER

BOLT TORX, M5x60

73 1950-86120 CLIP

74 T1513-15100 MUFFLER ASSY

76 4810-15140 • ARRESTER

77 T4950-57030 BOLT TORX, M5x70

78 T1513-15210 GASKET, MUFF

79 T2070-72210 CAP

80 1900-72120 SPRING

81 T1513-71240 CORD COMP.

83 T1513-71320 TUBE

84 3699-91667

1

SPARK PLUG, NGK CMR7A 1

85 5500-72130 GROMMET 1

91

92

93

94

87

88

89

90

4810-75100 RECOIL ASSY

4500-75120 • REEL

4500-75150 • SCREW

1850-75130 • SPRING

4500-75180 • COLLAR

4500-75190 • ARM

4810-75160 • ROPE

3330-75421 • KNOB

95

96

4810-75170 • PLATE

4500-75210 PULLEY

97 4820-85510 BOLT TORX, M5x16

98 T1513-82100 BODY ASSY

99 T1512-82130 • PLATE, CHOKE

100 T1600-82140 • LEVER

101 T1108-82190 • SCREW

102 T1513-82120 • PACKING

111

112

113

114

115

116

117

118

103 T1513-82170 ELEMENT

104 848-F02-83K0 PLATE

105 T1513-82200 COVER ASSY

106 T1108-82220 • KNOB

107 5516-83101 CABLE

108 T1504-85002 TANK ASSY

109 T1015-85202 • CAP ASSY

110 4500-85300 •• HOLDER ASSY

4500-85220

5601-85260

4820-85260

4810-85300

3302-85400

2841-31280

4820-85510

1133-82060

•• PACKING

•• FILTER

•• STOPPER

• PIPE COMP.

• FILTER ASSY

• COLLER

BOLT TORX, M5x16

LABEL, CHOKE

1

1

3

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

1

1

Q'ty

1

4

1

2

1

1

1

2

1

1

1

1

1

1

1

2

1

1

1

1

19 

Parts List

Fig.2 BLOWER GROUP HBZ2600

20 

Fig.2 BLOWER GROUP HBZ2600

Key# Part Number Description Q'ty

1 848-L0F-55A1 VOLUTE CASE 1

2 T4022-11301 VOLUTE COVER ASSY 1

3 1600-33130 SCREW 3

4 T4970-52001 SCREW TORX

5 T4033-31310 GURD NET

6 T4033-31320 SCREW

7 T4033-31330 WASHER

12

1

1

1

Key# Part Number

9 T4033-31350 SPRING

10 T4033-31360 SHAFT

11 T4033-32120 WASHER

12 T4970-51410 SCREW TORX

13 6811-11150 LEVER

14 6811-72200 SWITCH

15 T4022-11210 ENGINE COVER

16 4820-85510 BOLT TORX

17 T4960-53510 SCREW TORX

18

19

6811-12110

1650-43230

FAN

182301 NUT

20 6811-12220 WASHER

21 T4033-19111 LABEL, CAUTION

22 T4033-75611 LABEL, RECOIL

23 6811-51211 PIPE CT2-18

24 6811-51220 PIPE, END CT2-19

25 T4017-91130 SOCKET

1

1

2

1

1

1

1

1

2

4

1

1

1

1

1

1

1

Description Q'ty

OPTION

26

27

28

29

HBN-100 Flat Nozzle Set

6811-51210 • PIPE

6811-51230 • FIat Nozzle

DB00003 Vacuum Kit

30 T4027-52110 • PIPE, A

31 T4027-52120 • LABEL

32 T4027-52210 • PIPE, B

33 T4027-52310 • PIPE, C

34 T4027-52410 • EXTENSION

35 T4027-52510 • ELBOW

36 T4027-52610 • CLAMP

37 T4027-52710 • BAG, DUST

1

1

1

1

1

1

1

1

1

1

1

1

21

RedMax

LIMITED WARRANTY

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT,

KOMATSU ZENOAH AMERICA INC. (THE COMPANY),

THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH

SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR

WORKMANSHIP. EMISSION-RELATED PARTS ARE:

THE CARBURETOR ASSY, COIL ASSY, ROTOR, SPARKPLUG,

AIR FILTER, FUEL FILTER, INTAKE MANIFOLD, AND THE GASKETS

ALL OTHER PARTS EXCEPT ABOVE PARTS, FOR TWO (2) YEARS OF USE, 90 DAYS FOR RENTAL USE, FROM THE

DATE OF ORIGINAL PURCHASE, THE COMPANY, THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE

OF CHARGE, FOR THE ORIGINAL PURCHASER, ANY PART OF PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR

WORKMANSHIP. THIS IS THE EXCLUSIVE REMEDY.

THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER.

THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION

THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER.

THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS

DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.

ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR

WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF "REPAIR OR REPLACE AS

NECESSARY" SHALL BE WARRANTED FOR THE WARRANTY PERIOD.ANY WARRANTED PART WHICH IS

SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF

TIME UP TO THE FIRST SCHEDULED REPLACEMNET POINT FOR THE PART.

ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NON-

WARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE

COMPANY.

THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAILURE OF A

WARRANTED PARTS STILL UNDER WARRANTY.

THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF

INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS,

ACCIDENTAL MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBULICATION, USE OF ANY PARTS OR ACCESSARIES

OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE CONPANY'S CONTROL.

THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN

THEIR APPEARANCE.

THERE ARE NO OTHER EXPRESS WARRANTIES.

IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE LIMITED TO TWO (2) YEARS OF USE FROM THE ORIGINAL DELIVERY DATE.

LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES

ARE EXCLUDED.

SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMINATION OR EXCLUSION MAY

NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL KOMATSU

ZENOAH AMERICA INC. AT (770)-381-5147.

IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL

OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP

A COPY FOR YOUR RECORDS.

KOMATSU ZENOAH AMERICA INC.

4344 Shackleford Road Suite 500

Norcross, Georgia 30093

RedMax

Garantie limitée

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux pendant deux (2) ans à compter de la date initiale de livraison d’une unité. Les pièces en rapport avec les

émissions de gaz d'échappement sont: l'assemblage carburateur, l'assemblage bobine, le rotor, la bougie, le filtre à air, le filtre à carburant, la tubulure d'admission et les joints

Toutes les pièces autres que celles mentionnées ci-dessus, deux (2) ans d’utilisation, 90 jours pour la location, à compter de la date d’achat initial. La société, par l’intermédiaire d’un distributeur RedMax, réparera ou remplacera toute(s) pièce(s), sans frais et au bénéfice de l’acheteur original, en prenant en charge les frais de pièces et/ou de main d’œuvre. Telles sont les limites de la garantie.

Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge de l'acheteur.

L'acheteur ne supportera pas le coût de main d'oeuvre du diagnostic qui amène à la conclusion qu'une pièce garantie est défectueuse, si ce diagnostic est effectué chez le revendeur RedMax.

L’acheteur ou propriétaire a pour responsabilité d’effectuer l’entretien obligatoire tel que défini par le fabricant dans le manuel du propriétaire/de l'utilisateur.

Toute pièce garantie dont le remplacement n'est pas prévu dans le cadre de l’entretien obligatoire, ou pour laquelle est seulement prévue une inspection périodique pour "remplacement ou réparation si nécessaire" sera garantie pour la période de garantie. Toute pièce garantie arrivée à l’échéance de son premier remplacement prévu sera garantie jusqu’à celui-ci.

Toute pièce de rechange équivalente en performance ou en durabilité peut être utilisée pour l’entretien hors-garantie ou les réparations hors-garantie, et ce sans réduire l’obligation de garantie incombant à la société.

La société sera tenue responsable des dommages aux autres composants du moteur causés par la défaillance de pièce(s) garantie(s) en période de garantie.

La garantie ne s'applique pas aux unités endommagées par suite de: négligence dans la mise en oeuvre des instructions spécifiées dans le manuel du propriétaire/de l'utilisateur en vue d’une utilisation et d’un entretien correct, fausse manœuvre accidentelle, modification, utilisation abusive, lubrification incorrecte, utilisation de pièces ou d’accessoires autres que ceux spécifiés par la société, ou autres causes hors du contrôle de la société.

Cette garantie ne couvre pas les pièces remplacées en raison de leur usure normale ou de changements d’apparence sans effets.

Il n'existe aucune autre garantie explicite.

Les garanties implicites, y compris la valeur marchande et la valeur d’usage pour une utilisation particulière, sont

limitées à deux (2) ans d’utilisation à compter de la date originale de livraison.

Les responsabilités pour les dommage conséquents ou incidents sont exclues de toutes les garanties.

Certaines provinces n'autorisant pas les limitations à la durée des garanties implicites, ou les exclusions ou limitations relatives aux dommages incidents ou conséquents, la limitation indiquée ci-dessus peut ne pas vous être applicable.

Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits variant d'une province à l'autre.

Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez appeler KOMATSU

ZENOAH AMERICA INC. au (770)-381-5147

Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie pour vous.

KOMATSU ZENOAH AMERICA INC.

4344 Shackleford Road Suite 500

Norcross, Georgia 30093

KOMATSU ZENOAH AMERICA INC.

4344 Shackleford Road Suite 500

Norcross, Georgia 30093