Compaq Armada 1120 Service manual

Thank you for purchasing this Factory Service

Manual CD/DVD from servicemanuals4u.com.

Please check out our eBay auctions for more great deals on Factory Service Manuals:

servicemanuals4u

Notice

The information in this guide is subject to change without notice.

Compaq Computer Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.

This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation.

Copyright 1996 Compaq Computer Corporation.

All rights reserved. Printed in the U.S.A.

Compaq, Deskpro, LTE, Contura, Presario, ProLinea, QuickLock, QuickBlank

Registered U. S. Patent and Trademark Office. Contura Registered in the

Philippines Patent Office.

Armada is a trademark of Compaq Computer Corporation

Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft

Corporation.

The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement.

Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies.

MAINTENANCE AND SERVICE GUIDE

COMPAQ ARMADA 1100 FAMILY OF PERSONAL COMPUTERS

First Edition (June 1996)

Spare Part Number 262489-001

Document Part Number 262471-001

Preface

This Maintenance and Service guide is a troubleshooting guide that can be used for reference when servicing the Compaq Armada 1100 Family of

Personal Computers. Additional information is available in the SERVICE

QUICK REFERENCE GUIDE and in QUICKFIND.

Compaq Computer Corporation reserves the right to make changes to the

Compaq Armada 1100 Family of Personal Computers without notice.

Symbols

The following symbols and words mark special messages throughout this guide:

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of data.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

IMPORTANT: Text set off in this manner presents clarifying information or

specific instructions.

NOTE: Text set off in this manner presents commentary, sidelights, or

other points of information.

Technician Notes

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Only authorized technicians trained by Compaq should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To properly ventilate your system, you must provide at least 3 inches

(7.62 cm) of clearance on the front and back of the computer.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer is designed to be electrically grounded. To ensure proper operation, plug the AC power cord into a properly grounded electrical outlet only.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Serial Number

The serial number is displayed on the bottom of the CPU next to the memory compartment cover.

Locating Additional Information

The following documentation is available to support these products: o Quick Setup o Reference Guide o Introducing Microsoft Windows 95 o Compaq Service Quick Reference Guide o Service Training Guides o Compaq Service Advisories and Bulletins o Compaq QuickFind o Technical Reference Guide

Chapter 1 - Product Description

Computer Features and Models

The Compaq Armada 1100 Family of Personal Computers is a line of full-featured, Pentium-based portable computers. The following models are available: o Compaq Armada 1110 o Compaq Armada 1120 and Armada 1125 o Compaq Armada 1120T

This chapter describes the model offerings and features of the computers.

Models

The Compaq Armada 1100 Family of Personal Computers is available in the models shown in Table 1-1.

Table 1-1. Compaq Armada 1100 Family Models

===========================================================================

Model Processor Display Hard Drive

===========================================================================

Armada 1110 75-MHz Pentium 10.4-inch CSTN 810 MB

---------------------------------------------------------------------------

Armada 1120 100-MHz Pentium 10.4-inch CSTN 810 MB

Armada 1125

---------------------------------------------------------------------------

Armada 1120T 100-MHz Pentium 10.4-inch CTFT 810 MB

===========================================================================

Standard Features

The computers have the following standard features: o 75 or 100-MHz Pentium processors o 8 MB of dynamic random access memory (DRAM), expandable to 24 MB o 810 MB hard drive o 10.4-inch Color Super Twist Nematic (CSTN) or 10.4-inch Color Thin Film

Transistor (CTFT) VGA displays o Nickel metal hydride (NiMH) battery pack o Full-size 101-key compatible keyboard, including 12 function keys and

embedded numeric keypad o Integrated trackball o Operates from an internal battery pack or an AC adapter that is

compatible with domestic or international power sources o Power management and security features o Two PCMCIA standard device sockets that will accommodate Types I, II,

and III PC Cards o Rear panel ports provide connectors for parallel and serial ports, video

out, and keyboard/mouse port

Software Fulfillment

Backup software may be ordered directly from Compaq Computer Corporation through the Compaq Order Center. In Europe backup software may be ordered using the Software Diskette Order Form which is included in the For

Help... booklet. Both the model and serial numbers of the computer are needed to identify the specific software available.

For technical questions about software for the computer, contact a Compaq

Technical Support Engineer. The model and serial numbers of the computer should be available before making the call.

Security Features

The computer has the following security features: o Ability to secure the computer to an immovable object with an optional

cable lock.

o Ability to establish power-on and setup passwords.

o Ability to disable the following devices from the Security menu in

Computer Setup: serial port, parallel port, PC Card slots, diskette

drive, diskette drive boot ability.

Power Management

The computer supports three power management modes: o Local Standby: The ability to send individual subsystems into reduced

power modes after predetermined periods of inactivity.

o Global Standby: The ability to place all subsystems in a reduced power

mode after a predetermined period of inactivity.

o Hibernation: The ability to save the system configuration and user data

to the hard disk, for restoration at a later time.

The OFF and ON states also involve power management. In the OFF state, the computer appears to be consuming no power; however, as long as there is a battery capable of supplying current, some components will be powered up, performing housekeeping tasks and waiting to be awakened. In the ON state, all systems are powered up and the unit is completely functional.

Computer Options

The options for the computer that are available from Compaq are described in the following sections.

System Memory Options

The system memory options that are available from Compaq for the computers are 8 and 16 MB memory expansion boards. The memory expansion boards are

70-ns Fast Page Mode DRAM SODIMMs, without parity. Maximum memory is 24 MB of DRAM.

The expansion memory connector is a 144-pin SODIMM socket. Either parity or non-parity SODIMMs may be used, but parity checking will not be enabled by the memory controller.

Miscellaneous Options

The following options for the computer are also available from Compaq: o AC Adapter o Automobile Adapter o Extended Life NiMH battery pack o Slipcase o AC power cords for international travelers

AC Adapter

The AC adapter supplies DC voltage to the system converter to operate and/or charge the installed battery pack. The adapter provides sufficient power to charge the battery pack in 1.5 hours or less with the system off, or in 3.5 hours or less with the system on. The AC adapter power specifications are presented in Chapter 7.

Automobile Adapter

The automobile adapter is used to charge the computer while traveling in an automobile. The Auto Adapter power specifications are presented in

Chapter 7.

Nickel Metal Hydride Battery Pack

Nickel metal hydride battery packs are available for use with the Compaq

Armada 1100 Family of Personal Computers.

External Computer Components

The external computer components are shown and described in this section.

Front and Left Side Components

The front and left side external components are shown in the following figure and described in this section:

[1] Handle bracket (2)

[2] Keyboard tilt feet

[3] Diskette drive

[4] PC Card slots

[5] Display latches (2)

[6] PC Card release levers

[7] Battery compartment button

Rear Components

The rear components are shown in the following figure and identified in this section:

[1] Power connector

[2] Parallel connector

[3] Serial connector

[4] Keyboard/mouse connector

[5] External monitor connector

Bottom Components

The bottom external components are shown in the following figure and are identified in this section:

[1] Battery compartment

[2] Memory compartment

Status Panel Lights

The status panel lights are shown in the following figure and are identified in this section:

[1] Power/standby

[2] Battery charge

[3] Hard drive

[4] Diskette drive

[5] Battery gauge

[6] Caps Lock

[7] Scroll Lock

[8] Num Lock

System Design

This section provides an overview of the system design.

System Board and Processor

The OPTi-designed Viper-N Chipset provides PCI bus, ISA bus, cache controller, memory controller, and peripherals controller: o OPTi 82C557M System Controller o OPTi 82C556M Data Buffer Controller o OPTi 82C558E Integrated Peripherals Controller

The computer supports a 75-MHz (P54C) CPU at 50-MHz bus speed, and a

100-MHz (P54LM) CPU at 66-MHz bus speed. Bus speed and processor core voltage are configurable through resistor values at manufacturing. The processor is soldered to the system board and is not removable.

System Memory Options

The main memory subsystem supports a standard 8 MB DRAM, expandable to a maximum of 24 MB. The standard memory is soldered onto the system I/O board. Expansion memory is available in 8 or 16 MB increments.

Diskette Drive

The computer uses a standard 3.5-inch, 1.44 MB diskette drive. The system supports a single diskette drive in the computer.

Hard Drive

The computer supports an IDE hard drive. Cable select technology is employed for device 0/device 1 selection. The hard drive mounts to the system board with a hard drive bracket and connects directly to the system board. A screw secures the hard drive bracket in place.

Computer Design Overview

This section presents a brief design overview of the computer. See Chapter

3 for an overview of the system unit and the display assembly from the perspective of replacing components in the field. All replacement parts are listed in Chapter 3, and removal and replacement procedures are presented in Chapter 5.

The computer is a traditional clam shell design with a display unit and a system unit. The computer opens to reveal a backlighted LCD display and a full-sized keyboard. The display is designed to open to 135o.

System Unit

The major components of the system unit are: the CPU cover, keyboard, system board with processor, hard drive, diskette drive, memory expansion board, battery pack and compartment, integrated trackball assembly,

Real-Time Clock battery, and PC Card (PCMCIA) ejector rails and components.

Display Unit

The standard video subsystem consists of one of the following internal LCD displays: o 10.4-inch VGA CSTN display panel o 10.4-inch VGA CTFT display panel

In addition, the video subsystem consists of: o Cirrus Viking PCI Bus Graphics Accelerator with 1 MB EDO (two 70-ns

256kx 16) VRAM o An inverter to supply AC power to the LCD backlight system o A standard external VGA connector for use with CRTs and other VGA

compatible displays; also supported: external SVGA (maximum resolution

1024 x 768 x 256) o A flex cable connecting the system board to the LCD display and the

inverter o 48 KB of video ROM integrated into system ROM

Chapter 2 - Troubleshooting

Introduction

This chapter contains troubleshooting information for the computer. The basic steps in troubleshooting include:

1. Completing the preliminary steps listed in Section 2.1.

2. Running the Power-On Self-Test (POST) as described in Section 2.4.

3. Running the Computer Checkup (TEST) as described in Section 2.5.

4. Performing the recommended actions described in the diagnostic tables

in Section 2.7 if you are unable to exercise POST or Computer Checkup

or if the problem persists after running POST and Computer Checkup.

Adhere to the following guidelines when troubleshooting: o Complete the recommended actions in the order in which they are given.

o Repeat POST and Computer Checkup after each recommended action until the

problem is resolved and the error message does not return.

o Once the problem is resolved, do not complete the remaining recommended

actions.

o Refer to Chapter 5 for any removal and replacement procedures that are

recommended.

Preliminary Steps

IMPORTANT: Use the AC adapter when running POST, Computer Setup, or

Computer Checkup. A low battery condition could initiate

Standby and interrupt the test.

Before running POST and Computer Checkup, complete the following steps:

1. If a power-on password has been established, type the password and

press Enter.

NOTE: The key icon appears on the status display when the computer is

turned on to indicate that QuickLock/QuickBlank has been initiated.

Type the power-on password to exit QuickLock/QuickBlank. If the

password is unknown, it must be cleared (see Section 2.2).

2. Run Computer Setup (Section 2.3).

3. Use the Hotkeys to adjust the brightness (Fn+F9) and contrast (Fn+F10)

to the center of their ranges and leave the display open. On models

with color TFT displays, contrast is not adjustable.

4. Turn off the computer and all external devices.

5. Disconnect any external devices that you do not want to test. If you

want to use the printer to log error messages, leave it connected to

the computer.

NOTE: If a problem only occurs when an external device is connected to the

computer, the problem could be with the external device or its

cable. Isolate the problem by running POST with and without the

external device connected.

6. Use Advanced Diagnostics and loopback plugs in the serial and parallel

connectors if you plan to test these ports. To run Advanced

Diagnostics, complete the following steps:

a. Insert the Diagnostics diskette into the diskette drive and turn on

the computer.

b. At the Welcome Screen, enter Ctrl+A.

c. Press Enter to accept OK.

d. Select Computer Checkup (TEST).

e. Select Prompted Diagnostics after "Identifying System Hardware"

completes.

f. Select Interactive Testing and follow the displayed instructions.

7. Ensure that the battery pack is installed in the computer and the AC

adapter is connected to the computer and plugged into an AC power

source.

After completing the preliminary steps, run POST (Section 2.4) and

Computer Checkup (Section 2.5).

Running Computer Setup

The ROM-based Computer Setup displays the current system configuration and allows you to set system and power management parameters. These parameters are stored in CMOS, and a backup copy is saved in a parameter block in system flash ROM.

You can access Computer Setup by pressing F10 when the prompt appears after you turn on the computer. The following configuration parameters can be changed in Computer Setup: o Power conservation (when) o Power conservation (level) o Hibernation on/off o Hibernation settings o Warning beep o Setup password o Diskette drive disable o Serial ports disable o Parallel port disable o PC Card slots disable o Resume password on/off

o Boot memory test o Keyboard numlock o Boot sequence o Boot display o Serial port settings o Parallel port settings o Power-on password o Diskette drive boot disable

To run Computer Setup, complete the following steps:

Computer Setup automatically recognizes and configures the system for new

Compaq devices. It does this without prompting you for information about the devices. However, if you add a memory expansion board, a prompt appears the next time you turn on the computer, notifying you of the new memory configuration.

The first Computer Setup screen displays current settings for the system, ports, and devices. The status bar at the bottom of the screen gives instructions for navigating and choosing options. The status bar also displays descriptions as you highlight menus and menu options.

NOTE: If the main system board is replaced, the serial number on this

screen changes to 0 (zero).

Select one of the menus from the menu bar at the top of the screen to view or to change the following configuration settings: o Initialization startup preferences o Ports, including serial and parallel o Power, including Power Management and Hibernation o Security, including setup and power-on passwords and device disabling

Initialization Menu

Select the Initialization menu to change the initialization (startup) settings for running the POST memory tests, numlock on or off, the drive boot sequence, and the active display.

Ports Menu

Select the Ports menu to change the default input/output (I/O) addresses and interrupt requests (IRQs) for serial and parallel ports.

NOTE: If you select conflicting settings for the ports, the system

automatically changes one of the settings.

Power Menu

Select the Power menu to enable or disable Power Management, low-battery warning beeps, and an external energy-saving monitor. The factory default settings are:

o Power Management Enabled While on Battery o Conservation Level Medium o Low-Battery Warning Beeps Enabled o External Energy Saving Monitor Disabled

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

If you disable Power Management or Hibernation, you must take immediate action to resolve a low-battery condition to prevent losing unsaved information.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

If you elect to disable the low-battery warning beeps, a low-battery condition is indicated only by a blinking battery light. If you disable

Power Management or Hibernation, information in memory is not automatically saved during a critical low-battery condition.

If you enable the selection for an external energy-saving monitor, it enters low-power mode when the screen timeout occurs. If you enable this selection and do not have an energy-saving monitor, the screen display may become distorted.

Under Power Management, you can select whether to enable Power Management while on AC or battery power, only while on battery power, or never

(disabled).

If you enable Power Management, you can select from four conservation levels: high, medium, none (drain), or custom. The conservation level sets the timeouts for Standby, Hibernation, drives, and screens. A timeout is a period of inactivity after which power is turned off to the system or component.

o High: Provides the maximum amount of power conservation and the maximum

battery operating time from a single charge.

o Medium (default): Provides a balance between performance and battery

life.

o Custom: Conserves power according to specified timeout settings.

o None (Drain): Provides no power conservation features; the system runs

at full speed.

Security Menu

Select the Security menu to set, change, or delete the setup and power-on passwords and to enable/disable QuickLock/QuickBlank, power-on password from Standby, diskette drives, ports, and PC Card slots.

Setup Password

Use the Setup password to protect the system configuration from unauthorized changes. After you establish the setup password, you cannot change the system configuration until you enter the setup password.

IMPORTANT: Type carefully because the password does not display as you

type it. If you choose to, you can use the same password for

setup and for power-on.

The next time you press F10 (after POST) to run Computer Setup, a password prompt appears on the screen. If you enter the password incorrectly, you are prompted to reenter the password.

If you forget the setup password, you cannot change the system configuration until the computer memory is cleared of the password. Refer to Section 2.2 in this guide for procedures for clearing the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Record your setup password and put it in a safe place. If you forget your setup password, you cannot reconfigure the computer until the computer memory is cleared of the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Power-On Password

The power-on password prevents use of the computer until the password is entered. After you establish the power-on password, you must enter it whenever you turn on the computer.




You can also select to require the power-on password when exiting Standby.

The next time you start the computer or exit Standby, a password prompt appears. If you enter the password incorrectly, you are prompted to reenter the password.

If you forget the power-on password, you cannot use the computer until the computer memory is cleared of the password. Refer to Section 2.2 in this guide for procedures for clearing the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Record the power-on password and put it in a safe place. If you forget your power-on password, you cannot use the computer until the computer memory is cleared of the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

QuickLock/QuickBlank

Enabling QuickLock/QuickBlank allows you to temporarily disable the keyboard and clear the screen until the power-on password is entered.

After you have enabled QuickLock/QuickBlank, you can initiate it at any time by pressing the Fn+F6 hotkey.

When QuickLock/QuickBlank is initiated, the key icon on the status panel turns on. Type the power-on password on the blank screen to exit

QuickLock/QuickBlank.

Disabling Devices

The Security Menu provides a way to disable the following devices: o Serial port o Parallel port

o PC Card slots o Diskette drive

Disabling these devices prevents the unauthorized transfer of data using the devices. To reenable a device, deselect the Disable option and restart the computer.

Exit Menu

The Exit menu has four options: o Save and Exit: Saves configuration changes, but some changes do not take

effect until the computer is restarted.

o Exit (No Save): Exits and does not save the changes you have made.

o Restore Factory Defaults: Replaces the current configuration settings

with the original factory default settings.

POST Error Messages

This chapter contains typical error messages that you may encounter during the power-on self-test (POST). POST is a series of tests that run every time you turn on the computer. POST verifies that the system is configured and functioning properly. A successful POST is followed by one or two short beeps.

If you receive an error message listed on the following pages, follow the recommended action. If you receive an error message that is not listed, run Computer Checkup from the Diagnostics diskette. Information about running Computer Checkup is presented later in this chapter.

If POST detects an error, one of the following events occurs: o A message with the prefix "WARNING" appears informing you where the

error occurred. The system pauses until you press F1 to continue.

o A message with the prefix "FATAL" appears informing you where the error

occurred. After the message, the system emits a series of audible beeps.

The system then stops.

o The system emits a series of audible beeps. The system then stops.

Warning messages indicate a potential problem exists such as a system configuration error. When F1 is pressed, the system should resume. You should be able to correct problems that produce WARNING messages.

IMPORTANT: When a WARNING message includes the prompt to "RUN SCU," run

Computer Setup. (Computer Setup replaces the SCU utility.)

Fatal errors emit a beep and may display a FATAL message. Fatal errors indicate severe problems, such as a hardware failure. Fatal errors do not allow the system to resume. Some of the Fatal error beep codes are listed at the end of this section.

Table 2-1. Warning Messages

===========================================================================

Message Description

===========================================================================

Clock not ticking correctly The real time clock is not ticking.

---------------------------------------------------------------------------

CMOS checksum invalid, run CMOS RAM information has been corrupted and

SCU needs to be reinitialized by running Computer

Setup.

---------------------------------------------------------------------------

CMOS failure, run SCU CMOS RAM has lost power and needs to be

reinitialized by running Computer Setup.

---------------------------------------------------------------------------

Floppy controller failed The diskette drive controller failed to

respond to the reset command. Power down the

system and check all appropriate connections.

If the diskette drive controller continues to

fail, you may need to replace the system

board.

---------------------------------------------------------------------------

Floppy disk track 0 failed The diskette drive cannot read track 0 of the

diskette in the drive. Try another diskette.

If the problem persists, you may need to

replace the diskette drive.

---------------------------------------------------------------------------

Floppy information invalid, The drive parameters stored in CMOS RAM do run SCU not match the diskette drives detected in the

system. Run Computer Setup

---------------------------------------------------------------------------

Hard disk controller error The hard drive controller failed to respond

to the reset command. Check the drive

parameters. Power down the system and check

all appropriate connections.

---------------------------------------------------------------------------

Hardware information does The video adapter type specified in CMOS RAM not match video card, run does not match the installed hardware. Run

SCU Computer Setup

---------------------------------------------------------------------------

Keyboard controller failure The keyboard failed the self-test command.

---------------------------------------------------------------------------

Keyboard failure The keyboard failed to respond to the RESET

ID command.

---------------------------------------------------------------------------

No interrupts from Timer 0 The periodic timer interrupt is not

occurring.

---------------------------------------------------------------------------

RAM parity error at A RAM parity error occurred at the specified location xxxx (hex) location.

---------------------------------------------------------------------------

ROM at xxxx (LENGTH yyyy) An illegal adapter ROM was located at the with nonzero checksum (zz) specified address. An external adapter (such

as a video card) may be causing the conflict.

---------------------------------------------------------------------------

Time/Date corrupt - run SCU The time and date stored in the real time

clock have been corrupted, possibly by a

power loss. Run Computer Setup.

---------------------------------------------------------------------------

Unexpected amount of The amount of memory detected by POST does memory, run SCU not match the amount specified in CMOS RAM.

Run Computer Setup.

---------------------------------------------------------------------------

Hard disk xx failure A failure or an error occurred when trying to

(or error) access the hard drive.

===========================================================================

Table 2-2. Fatal Error Messages

===========================================================================

Message Description Beep Code

===========================================================================

CMOS RAM test failed A walking bit test of CMOS RAM

location 0E (Hex) - 3F (Hex) failed. 3

---------------------------------------------------------------------------

DMA controller faulty A sequential read/write of the

transfer count and transfer address

registers within the primary and

secondary DMA controllers failed. 4

---------------------------------------------------------------------------

Faulty DMA page registers A walking bit read/write of the 16 DMA

controller page registers starting at

location 80 Hex failed. 0

---------------------------------------------------------------------------

Faulty refresh circuits A continuous read/write test of port

61h found that bit 4 (Refresh Detect)

failed to toggle within an allotted

amount of time. 1

---------------------------------------------------------------------------

Interrupt controller failed A sequential read/write of various

Interrupt Controller registers failed. 5

---------------------------------------------------------------------------

ROM checksum incorrect A checksum of the ROM BIOS does not

match the byte value at F000:FFFF. 2

---------------------------------------------------------------------------

RAM error at location xxxx RAM error occurred during memory test. None

---------------------------------------------------------------------------

Parity error at unknown location Parity error occurred. None

===========================================================================

The following table lists some of the Fatal Error beep codes, along with the beep sequence (short, long, pause) and the meaning of the beeps.

Table 2-3. Fatal Error Beep Codes

===========================================================================

Beep Code Beep Sequence Explanation Remedy

===========================================================================

0 S-S-S-P-S-S-L-P The DMA page

registers are faulty. Replace system board.

1 S-S-S-P-S-L-S-P The refresh circuitry

is faulty. Replace system board.

2 S-S-S-P-S-L-L-P The ROM checksum is 1. Flash the ROM

incorrect. 2. Replace system

board.

3 S-S-S-P-L-S-S-P The CMOS RAM test

failed. Replace system board.

4 S-S-S-P-L-S-L-P The DMA controller is

faulty. Replace system board.

5 S-S-S-P-L-L-S-P The interrupt

controller failed. Replace system board.

6 S-S-S-P-L-L-L-P The keyboard

controller failed. Replace system board.

7 S-S-L-P-S-S-S-P Graphics adapter is

faulty. Replace system board.

8 S-S-L-P-S-S-L-P Internal RAM is

faulty. Replace processor

board.

---------------------------------------------------------------------------

S = Short, L = Long, P = Pause

===========================================================================

Compaq Diagnostics

Run the Compaq Diagnostics utilities diskette when you want to view or test system information and installed or connected devices. The

Diagnostics menu includes the following utilities: o Computer Checkup (TEST) o View System Information (INSPECT) o Prepare Computer for a Compaq Service Call (RemotePaq)

If you have a problem you cannot solve, run the Diagnostics utilities before you call for support. Run Computer Checkup and select to save the device list to a file and to print or to save the log of errors. Run the

View System Information (INSPECT) utility and select to print or to save that information. Have the files or the printed information available when you call for support.

Computer Checkup (TEST)

Computer Checkup (TEST) determines whether the various computer components and devices are recognized by the system and are functioning properly. You can display, print, or save the information generated by Computer Checkup.

Follow these steps to run Computer Checkup:

1. Plug the computer into an external power source. (A low battery

condition could interrupt the program.)

2. Turn on the external devices that you want to test. Connect the printer

if you want to print a log of error messages.

3. Insert the Compaq Diagnostics diskette in drive A.

4. Turn on or restart the computer. The computer starts from drive A, and

the Diagnostics Welcome screen appears.

5. Press Enter to continue. The Diagnostics menu appears.

6. Select Computer Checkup from the Diagnostics menu. A Test Option menu

appears.

7. Select "View the Device List" from the Test Option menu. A list of the

installed Compaq devices appears.

8. If the list of installed devices is correct, select OK. The Test Option

menu appears.

NOTE: If the list is incorrect, ensure that any new devices are

installed properly.

9. Select one of the following from the Test Option menu:

o Quick Check Diagnostics. Runs a quick, general test on each device

with a minimal number of prompts. If errors occur, they display when

the testing is complete. You cannot print or save the error

messages.

o Automatic Diagnostics. Runs unattended, maximum testing of each

device with minimal prompts. You can choose how many times to run the

tests, to stop on errors, or to print or save a log of errors.

o Prompted Diagnostics. Allows maximum control over testing the

devices. You can choose attended or unattended testing, decide to

stop on errors, or choose to print or save a log of errors.

10. Follow the instructions on the screen as the devices are tested. When

testing is complete, the Test Option menu appears.

11. Exit the Test Option menu.

12. Exit the Diagnostics menu.

View System Information (INSPECT)

The View System Information (INSPECT) utility provides information about the computer and installed or connected devices. You can display, print, or save the information.

Follow these steps to run INSPECT from the Compaq Diagnostics diskette:

1. Turn on the external devices that you want to test. Connect the printer

if you want to print the information.

2. Insert the Compaq Diagnostics diskette into drive A.




5. Select View System Information (INSPECT) from the Diagnostics menu.

6. Select the item you want to view from the following list:

===========================================================================

System Memory

===========================================================================

ROM Audio

Keyboard Operating system

System ports System files

System storage Windows files

Graphics

===========================================================================

7. Follow the instructions on the screen to cycle through the screens, to

return to the list and choose another item, or to print the

information.

RemotePaq

This utility is only available in certain geographical areas and requires a modem. It allows a Compaq reseller or service provider to automatically run diagnostics on the computer.

To run RemotePaq, follow these steps:

1. Insert the Compaq Diagnostics diskette into drive A.




4. Select Prepare Computer for a Compaq Service Call (RemotePaq).

5. Follow the instructions on screen.

Diagnostic Error Codes

Diagnostic error codes occur if the system recognizes a problem while running the Compaq Diagnostic program. These error codes help identify possibly defective subassemblies.

Tables 2-4 through 2-13 list possible error codes, a description of the error condition, and the action required to resolve the error condition.

IMPORTANT: Retest the system after completing each step. If the problem

has been resolved, do not proceed with the remaining steps.

For assistance in the removal and replacement of a particular subassembly, see Chapter 5, "Computer Removal and Replacement Procedures."

Table 2-4. Processor Test Error Codes

===========================================================================

Error Code Description Recommended Action

===========================================================================

101 - xx CPU test failed The following applies to error codes

101 - xx through 113 - xx:

103 - xx DMA page registers

test failed Replace the system board and retest.

104 - xx Interrupt controller

master test failed

105 - xx Port 61 error

106 - xx Keyboard controller

self-test failed

107 - xx CMOS RAM test

failed

108 - xx CMOS interrupt test

failed

109 - xx CMOS clock test

failed

110 - xx Programmable timer load data test failed

113 - xx Protected mode test

failed

---------------------------------------------------------------------------

114 - 01 Speaker test failed 1. Check system configuration.

2. Verify cable connections to speaker.

3. Replace the system board and retest.

===========================================================================

Table 2-5. Memory Test Error Codes

===========================================================================


===========================================================================

200 - xx Memory machine ID The following steps apply to error

test failed codes 200 - xx and 202 - xx:

202 - xx Memory system ROM 1. Flash the system ROM and retest.

checksum failed 2. Replace the system board and retest.

---------------------------------------------------------------------------

203 - xx Write/Read test The following steps apply to error

failed codes 203 - xx through 215 - xx:

204 - xx Address test failed 1. Remove the memory module and retest.

2. Install a new memory module and

211 - xx Random pattern test retest.

failed

214 - xx Noise test failed

215 - xx Random address test

failed

===========================================================================

Table 2-6. Keyboard Test Error Codes

===========================================================================


===========================================================================

300 - xx Failed ID Test The following steps apply to error

codes 300 - xx through 304 - xx:

301 - xx Failed Self-test/ 1. Check the keyboard connection. If

Interface Test disconnected, turn off the computer

and connect the keyboard.

2. Replace the keyboard and retest.

302 - xx Failed Individual 3. Replace the system board and retest.

Key Test

304 - xx Failed Keyboard

Repeat Test

===========================================================================

Table 2-7. Parallel Printer Test Error Codes

===========================================================================


===========================================================================

401 - xx Printer failed or The following steps apply to error

not connected codes 401 - xx through 403 - xx:

402 - xx Failed Port Test 1. Connect the printer.

2. Check power to the printer.

403 - xx Printer pattern test 3. Install the loopback connector and

failed retest.

4. Check port and IRQ configuration.


===========================================================================

Table 2-8. Diskette Drive Test

===========================================================================


===========================================================================

600 - xx Diskette ID drive The following steps apply to error

types test failed codes 600 - xx through 698 - xx:

601 - xx Diskette format 1. Replace the diskette media and

failed retest.

2. Check and/or replace the diskette

602 - xx Diskette read test power and signal cables and retest.

failed 3. Replace the diskette drive and

retest.

603 - xx Diskette write, 4. Replace the system board and

read, compare test retest.

failed

604 - xx Diskette random

read test failed

605 - xx Diskette ID media

failed

606 - xx Diskette speed test

failed

609 - xx Diskette reset

controller test

failed

610 - xx Diskette change

line test failed

697 - xx Diskette type error

698 - xx Diskette drive speed

not within limits

---------------------------------------------------------------------------

699 - xx Diskette drive/media 1. Replace media.

ID error 2. Run the Configuration and

Diagnostics Utilities.

===========================================================================

Table 2-9. Serial Test Error Codes

===========================================================================


===========================================================================

1101 - xx Serial port test 1. Check port configuration

failed 2. Replace the system board and retest.

===========================================================================

Table 2-10. Hard Drive Test Error Codes

===========================================================================


===========================================================================

1701 - xx Hard drive format The following steps apply to error

test failed codes 1701 - xx through 1736 - xx:

1702 - xx Hard drive read test 1. Run the Diagnostics Utilities

failed and verify drive type.

2. Replace the hard drive and retest.

1703 - xx Hard drive write/ 3. Replace the system board and

read/compare test retest.

failed

1704 - xx Hard drive random

seek test failed

1705 - xx Hard drive

controller test

failed

1706 - xx Hard drive ready

test failed


recalibration test

failed

1708 - xx Hard drive format

bad track test

failed

1709 - xx Hard drive reset

controller test

failed

1710 - xx Hard drive park

head test failed

1715 - xx Hard drive head

select test failed


conditional format

test failed

1717 - xx Hard drive ECC *

test failed

1719 - xx Hard drive power

mode test failed

1724 - xx Network preparation

test failed

1736 - xx Drive monitoring

test failed

---------------------------------------------------------------------------

* ECC = Error Correction Code

===========================================================================

Table 2-11. Video Test Error Codes

===========================================================================


===========================================================================

501 - xx Video controller The following apply to error codes

test failed 501 - xx through 516 - xx:

502 - xx Video memory test 1. Disconnect external monitor and test

failed with internal LCD display.

2. Replace the display assembly and

503 - xx Video attribute test retest.

failed 3. Replace the system board and retest.

504 - xx Video character set

test failed

505 - xx Video 80 x 25

mode 9 x 14

character cell test

failed

506 - xx Video 80 x 25 mode

8 x 8 character

cell test failed


test failed

508 - xx Video 320 x 200

mode color set 0

test failed

509 - xx Video 320 x 200

mode color set 1

test failed

510 - xx Video 640 x 200

mode test failed

511 - xx Video screen memory

page test failed

512 - xx Video gray scale

test failed

514 - xx Video white screen

test failed

516 - xx Video noise pattern

test failed

---------------------------------------------------------------------------


---------------------------------------------------------------------------

2402 - xx Video memory test The following steps apply to error

failed codes 2402 - xx through 2456 - xx:

2403 - xx Video attribute test 1. Run the Configuration and

failed Diagnostics Utilities.


2404 - xx Video character set retest.

test failed 3. Replace the system board and retest.


9 x 14 character

cell test failed


8 x 8 character

cell test failed

2408 - xx

2409 - xx Video 320 x 200

mode color set 1

test failed

2410 - xx Video 640 x 200

mode test failed

2411 - xx Video screen

memory page test

failed

2412 - xx Video gray scale

test failed

2414 - xx Video white screen

test failed

2416 - xx Video noise

pattern test

failed

2418 - xx ECG/VGC memory

test failed

---------------------------------------------------------------------------


---------------------------------------------------------------------------

2419 - xx ECG/VGC ROM checksum The following steps apply to error

test failed codes 2402 - xx through 2456 - xx:

2421 - xx ECG/VGC 640 x 200 1. Run the Diagnostics Utilities.

graphics mode test 2. Disconnect external monitor and

failed retest with internal LCD monitor.


2422 - xx ECG/VGC 640 x 350 retest.

16 color set test 4. Replace the system board and retest.

failed

2423 - xx ECG/VGC 640 x 350

64 color set test

failed

2431 - xx 640 x 480 graphics

test failure

2432 - xx 320 x 200 graphics

(256 color mode)

test failure

2448 - xx Advanced VGA

Controller test

failed

2451 - xx 132-column Advanced

VGA test failed

2456 - xx Advanced VGA 256

Color test failed

---------------------------------------------------------------------------

2458 - xx Advanced VGA BitBLT Replace the system board and retest.

test

2468 - xx Advanced VGA DAC

test

2477 - xx Advanced VGA data

path test

2478 - xx Advanced VGA BitBLT

test

2480 - xx Advanced VGA

Linedraw test

===========================================================================

Table 2-12. Audio Test Error Codes

===========================================================================


===========================================================================

3206 - xx Audio System Replace the system board and retest.

Internal Error

===========================================================================

Table 2-13. Pointing Device Interface Test Error Codes

===========================================================================


===========================================================================

8601 - xx Mouse test failed The following steps apply to 8601 - xx

and 8602 - xx:

8602 - xx Interface test

failed 1. Replace the Pointing Device and

reset.


===========================================================================

Troubleshooting without Diagnostics

This section provides information about how to identify and correct some common hardware, memory, and software problems. It also explains several types of common messages that may be displayed on the screen. The following pages contain troubleshooting information on: o Audio o Memory o Battery/Battery gauge o PC Card o Diskette/Diskette drive o Power o Hard drive o Printer o Hardware installation o Screen (LCD and CRT) o Keyboard (Numeric keypad) o Software o Pointing device

Solving Minor Problems

Some minor problems and possible solutions are outlined in the following tables. If the problem appears related to a software application, check the documentation provided with the software.

Solving Audio Problems

Some common audio problems and solutions are listed in the following table.

Table 2-14. Solving Audio Problems

===========================================================================

Problem Probable Cause Solution(s)

===========================================================================

Computer beeps once This is typical; it No action is required.

after you turn it indicates successful on. completion of the Power-On

Self-Test (POST).

---------------------------------------------------------------------------

Computer does not Speaker volume is off or If the speaker icon is beep after the has been turned down. not displayed on the

Power-On Self-Test status panel, Press

(POST). Fn+F5 to turn the

speaker on, then adjust

the volume.

Beeps have been turned Run Computer Setup and

off. turn on beeps.

===========================================================================

Solving Battery and Battery Gauge Problems

Some common causes and solutions for battery problems are listed in the following table. The "Solving Power Problems" section in this chapter also may be applicable.

Table 2-15. Solving Battery and Battery Gauge Problems

===========================================================================


===========================================================================

Computer won't turn Battery is discharged. Connect the computer to on when battery pack an external power is inserted and source and charge the power cord is battery pack.

unplugged.

Replace the battery pack

with a fully charged

battery pack.

Check the battery

connectors on the system

board to verify they are

evenly spaced and that

they are not bent or

broken.

---------------------------------------------------------------------------

Computer is beeping Battery charge is low. Immediately save any open and battery light file(s). Then do any one is blinking. of the following:

o Connect the computer to

an external power

source to charge the

battery pack.

o Initiate Standby and

replace the battery

pack with a fully

charged battery pack.

o Turn the computer off

or initiate Hibernation

until you can find

another power source or

charge the battery

pack.

---------------------------------------------------------------------------

Computer battery Low battery beeps Run Computer Setup to light blinks to were turned off. turn on the low battery indicate low battery warning beeps.

condition, but computer does not beep.

Volume is turned off or Press Fn+F5 to turn the

turned down too low. speaker on and then

adjust the volume.

---------------------------------------------------------------------------


---------------------------------------------------------------------------

Battery light Battery pack is already No action is necessary.

doesn't light and charged.

battery pack won't fast charge.

Battery pack was exposed Allow time for the

to temperature extremes. battery pack to return to

room temperature.

Battery pack is at end Replace battery pack.

of its life.

---------------------------------------------------------------------------

You have to set the Auxiliary battery charge Provide power to the date and time every is low, or the auxiliary computer (AC or battery).

time you turn on battery is at end of its the computer. life. Replace the RTC (lithium)

battery.

---------------------------------------------------------------------------

Battery charge does Battery is being exposed Keep the battery pack not last as long as to high temperatures or within the recommended expected. extremely cold temperature ranges:

temperatures.

Operating: 50oF to 104oF

(10oC to 40oC)

Storage: -4oF to 86oF

(-20oC to 30oC).

Recharge the battery

pack.

Battery has partially Recharge the battery.

self-discharged. Discharge the battery

completely and then

recharge it.

Power management is Set a power management

disabled. level in Computer Setup.

An external device or Turn off or disconnect

PC Card is draining the external devices when not

battery. using them.

---------------------------------------------------------------------------

Battery pack is Normal warming has No action is required.

warm to the touch occurred due to after charging. charging.

---------------------------------------------------------------------------

Battery gauge is The battery pack is new Fully charge the battery inaccurate. or has not been used for pack until the battery

a long period. light on the computer

turns off.

Condition the battery

pack by fully charging,

then fully discharging,

and then fully

recharging. If condition

persists, replace the

battery. If the battery

gauge is still

inaccurate, replace the

system board.

---------------------------------------------------------------------------

Battery pack Power management is Enable power management operating time is turned off or disabled. in Computer Setup and in far less than the Windows Power Properties.

documented The power management icon average operating should be visible on the time. status panel.

An external device or Turn off or disconnect

PC Card is draining the external devices when not

battery. using them.

Battery pack has Condition the battery

partially self- pack by fully charging,

discharged. fully discharging, then

fully recharging it.

To maintain the charge,

leave battery packs in

the computer when it is

connected to external

power.

If the computer is

disconnected from

external power for more

than two weeks, remove

battery packs from the

computer to reduce the

discharge rate.

---------------------------------------------------------------------------


---------------------------------------------------------------------------

Battery pack is being Keep the battery pack

exposed to high within the recommended

temperatures or temperature ranges.

extremely cold

temperatures. operating: 50oF to 104oF

(10oC to 40oC)

storage: -4oF to 86oF

(-20oC to 30oC ).

Recharge the battery

pack.

===========================================================================

Solving Diskette and Diskette Drive Problems

Some common causes and solutions for diskette and diskette drive problems are listed in the following table.

Table 2-16. Solving Diskette and Diskette Drive Problems

===========================================================================


===========================================================================

Diskette drive icon Diskette drive is not Remove the diskette drive does not turn on. installed properly. and install it properly.

---------------------------------------------------------------------------

Diskette drive icon Diskette is damaged. Run SCANDISK on the stays on. diskette. At the system

prompt, enter SCANDISK A:

Diskette is incorrectly Remove diskette and

inserted. reinsert.

Software program is Check the program

damaged. diskettes.

---------------------------------------------------------------------------

Diskette drive Diskette is Disable the diskette's cannot write to a write-protected. write-protect feature or diskette. use a diskette that is

not write-protected.

Computer is writing to Check the drive letter in

the wrong drive. the path statement.

Not enough space is left Use another diskette.

on the diskette.

Drive error has Run Computer Checkup

occurred. from the Compaq

Diagnostics diskette.

Diskette is not Format the diskette. At

formatted. the system prompt, enter

FORMAT A:

---------------------------------------------------------------------------

Diskette drive The wrong type of Use the type of diskette cannot read a diskette is being used. required by the drive.

diskette.

Diskette has a bad Copy files to hard drive

sector. or another diskette.

Reformat bad floppy.

Drive error has Run Computer Checkup

occurred. from the Compaq

Diagnostics diskette.

Diskette is not Format the diskette. At

formatted. the system prompt, enter

FORMAT A:

---------------------------------------------------------------------------

Cannot boot from Bootable diskette is not Put the bootable diskette diskette in drive A in drive A.

Diskette Boot is Run Computer Setup and

disabled in Computer enable Diskette Boot on

Setup. the Initialization menu.

===========================================================================

Solving Hard Drive Problems

Some common causes and solutions for hard drive problems are listed in the following table.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To prevent loss of information, always maintain an up-to- date backup of your hard drive at all times, in case of errors or failures.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Table 2-17. Solving Hard Drive Problems

===========================================================================


===========================================================================

Reading hard drive System entered Give the system time to takes an unusually Hibernation due to restore the previously long time after low-battery condition saved data to its exact restarting the and is now exiting from state before Hibernation.

computer. it.

---------------------------------------------------------------------------

Hard drive error Hard drive has bad Run Computer Checkup from occurs. sectors or has failed. the Compaq Diagnostics

diskette.

See POST error messages.

===========================================================================

Solving Hardware Installation Problems

Some common causes and solutions for hardware installation problems are listed in the following table.

Table 2-18. Solving Hardware Installation Problems

===========================================================================


===========================================================================

A new device is not Cable(s) of new external Ensure that all cables recognized as part device are loose or are properly and securely of the computer power cables are connected.

system. unplugged.

Power switch of new Turn off the computer,

external device is not turn on the external

turned on. device, then turn on the

computer to integrate

the device with the

computer system.

Device is not seated Turn off the computer

properly. and reinsert the device.

===========================================================================

Solving Keyboard/Numeric Keypad Problems

Some common causes and solutions for keyboard/numeric keypad problems are listed in the following table.

Table 2-19. Solving Keyboard/Numeric Keypad Problems

===========================================================================


===========================================================================

Embedded numeric Num Lock function is not Press the Fn+NumLk keys keypad on computer enabled. to enable the Num Lock keyboard is function and embedded disabled. numeric keypad. The Num

Lock icon on the status

panel turns on.

---------------------------------------------------------------------------

Embedded numeric External numeric keypad Disconnect the external keypad is disabled is connected to the numeric keypad from the and Num Lock computer. computer.

function is on.

---------------------------------------------------------------------------

Keyboard is locked. You initiated QuickLock. Enter your password to

exit QuickLock.

===========================================================================

Solving Pointing Device Problems

Some common causes and solutions for trackball and mouse problems are listed in the following table.

Table 2-20. Solving Pointing Device Problems

===========================================================================


===========================================================================

External pointing The device driver is not Install the device driver device does not installed in Windows. in Windows.

work.

---------------------------------------------------------------------------

Integrated pointing An external pointing Initiate Standby and device does not device is connected disconnect the external work. and the system has pointing device.

disabled the internal

pointing device.

===========================================================================

Solving Memory Problems

Some common causes and solutions for memory problems are listed in the following table.

Table 2-21. Solving Memory Problems

===========================================================================


===========================================================================

Memory count during Optional memory Ensure that the optional

Power-On Self-Test expansion card is memory expansion card is

(POST) is incorrect. installed incorrectly, installed correctly.

is incompatible with the

computer, or is

defective.

---------------------------------------------------------------------------

"Out of Memory" System ran out of memory Check the application message is displayed for the application. documentation for on the screen or memory requirements.

insufficient memory Install additional error occurs during memory.

operation.

Too many TSR (terminate Remove from memory any

and stay resident) TSR applications that

applications are you do not need.

running.

===========================================================================

Solving PC Card Problems

Some common causes and solutions for PC Card problems are listed in the following table.

Table 2-22. Solving PC Card Problems

===========================================================================


===========================================================================

PC Card error The PC Card slot is Run Computer Setup and messages appear when disabled. enable the PC Card slots the computer is on the Security Menu.

turned on.

When turned on, the Card is not inserted Ensure the card is computer does not properly. inserted in the correct beep when a PC orientation.

Card is inserted.

PC Card beeps are Double-click the PC Card

disabled. icon in the Control

Panel, click the Global

Settings tab, the enable

PC Card sound effects.

Speaker is turned off. Press Fn+F5 to turn the

speaker on.

PC Card drivers are not Double click the Add New

installed. Hardware icon in the

Control Panel for

installation

instructions.

If PC Card or drivers are

not compatible with

Windows 95, install

drivers and use the PC

Card in MS-DOS mode.

The PC Card slots are Run Computer Setup and

disabled. then select the Security

menu to enable PC Card

slots.

Card or card driver is Contact your Compaq

not supported. authorized service

provider for a list of

PC Cards tested

successfully in Compaq

PC Card platforms.

---------------------------------------------------------------------------

The PC Card drivers The PC Card slot is Run Computer Setup and

(Socket Services, disabled. select the Security menu

Card Services, Card to enable PC Card slots.

ID) fail with error messages when the computer is turned on.

---------------------------------------------------------------------------

PC Card modem, fax, Card is not fully Ensure the card is or network card inserted into the slot inserted in the correct does not work. or is not inserted orientation.

properly.

Telephone cord is not Check and secure

plugged in all the way. telephone connection.

Necessary drivers are Install drivers.

not installed (turned

on).

---------------------------------------------------------------------------

PC Card modem or fax You are trying to access Right click My Computer card does not work. the card using the wrong on the Windows desktop.

COM port. Left click Properties,

then Device Manager,

and double-click Port

Settings to view the

COM port settings.

The card conflicts with

a serial device.

The card is not Use supported cards

supported. only.

---------------------------------------------------------------------------

Modem network PC Network driver is not Install driver.

Card does not work. installed or is not set

up properly.

Telephone cord is not Verify telephone

properly connected. connection.

---------------------------------------------------------------------------

Memory or storage SRAM and flash memory Install driver.

card does not work. cards require the memory

card driver to be loaded

(turned on).

Flash memory cards

require the Microsoft

FlashFile System to be

loaded.

Hard drives on flash

mass storage cards

require the PC Card ATA

driver to be loaded.

You are trying to Double-click My Computer

access the hard drive to verify the drive

card using the wrong letter assigned to the

drive letter. card.

The card is not Check the list of PC

supported. Cards tested successfully

in Compaq PC Card

platforms.

===========================================================================

Solving Power Problems

Also see "Solving Battery and Battery Gauge Problems" in this chapter.

Table 2-23. Solving Power Problems

===========================================================================


===========================================================================

Computer won't turn Computer is not Insert battery or connect on and battery pack connected to a power an external power source.

is not inserted. source.

Power cords to the Ensure that power cords

external power source connecting the computer

are unplugged. and the external power

source are plugged in

properly.

System board is 1. See section

defective. "Measuring Power

Signals" to check for

proper voltages.

2. Replace system board

and restart.

---------------------------------------------------------------------------

Computer turned off System initiated Replace the battery pack while it was left Hibernation due to a with a fully charged unattended and the critical low-battery battery pack or connect power icon is off. condition. the computer to an

external power source.

Then turn on the

computer.

System initiated Turn on the computer.

Hibernation after a

preset timeout.

---------------------------------------------------------------------------

Computer initiated The unit temperature was Computer is in an

Standby exceeded. exceedingly hot automatically or environment. Let the turned off computer cool down.

automatically.

===========================================================================

Measuring Power Signals

The following power signals can be measured on the top side of the PCA.

===========================================================================

VDD (+5V) Across Tantalum CAPs C574, C573

---------------------------------------------------------------------------

+3.3V Across Tantalum CAPs C578, C575

---------------------------------------------------------------------------

VCPU (3.3V on -001 and 2.9V on -002) Across Tantalum CAPs C572, C571, C570, and C569

---------------------------------------------------------------------------

VBAT At Fuse F1

---------------------------------------------------------------------------

+12V Across CAP C522, near PCMCIA connector

===========================================================================

VCC1 can be measured at Pin 28 of U539.

Solving Printer Problems

If you experience problems printing, run a printer self-test. Refer to the documentation provided with your printer for instructions. If the self-test fails, it is a printer-specific problem. Also refer to the printing section of your application documentation.

Table 2-24. Solving Printer Problems

===========================================================================


===========================================================================

Printer will not The signal cable may not Ensure that the signal turn on. be connected properly, cable is properly

or the printer is connected and that the

unplugged. power cord is connected

to the electrical outlet.

---------------------------------------------------------------------------

Printer will not Printer is not turned on Turn the printer on and print. or is off line. set it to online.

The device drivers for Refer to the printer

your application are not documentation to Install

installed. the correct printer

driver.

Printer that is set up Connect the printer to

for a network is not the network.

connected to the

network.

Printer cable is too Replace the cable.

long, unshielded, or

defective.

Paper tray is empty. Fill the paper tray with

paper and set the

printer to on line.

---------------------------------------------------------------------------

Printer prints Correct printer drivers Refer to the printer garbled are not installed. documentation to Install information. the correct printer

driver.

Cable is not connected Ensure that the printer

properly. signal cable is properly

connected to the

computer.

Cable is defective. Replace the printer

cable and retest.

===========================================================================

Solving Screen Problems

This section lists some common causes and solutions for computer display and external monitor problems.

IMPORTANT: Verify that the display jumpers are set properly for the

display before proceeding with any troubleshooting.

You can perform a monitor self-test on an external VGA color or monochrome monitor by disconnecting the monitor from the computer. To do so, complete the following steps:

1. Turn off the monitor.

2. Turn off the computer.

3. Disconnect the monitor signal cable from the computer.

4. Turn on the monitor and allow it to warm up for one minute.

The screen should be white. A narrow black border may also appear on

the left and right sides of the display. Either of these displays

indicates that the monitor is working properly.

Table 2-25. Solving Screen Problems

===========================================================================


===========================================================================

Characters are dim. The brightness or Adjust the control(s) on

contrast (if applicable) the right side of the

control is not set computer display.

properly.

Computer screen is in Tilt the display or move

direct light. computer.

---------------------------------------------------------------------------

Screen is blank. You initiated QuickLock/ Enter the password to

QuickBlank. exit QuickLock/

QuickBlank.

You may have another Press any key and/or

screen blanking utility enter your password.

installed.

Screen save was Press any key or click

initiated after the the mouse.

Power Management timeout

period of inactivity

If an STN screen is Use the control on the

used, brightness/ display to adjust the

contrast needs brightness/contrast.

adjusting.

Standby was initiated. Press the standby button

to exit Standby.

---------------------------------------------------------------------------

Computer screen is Display was switched to Press the Fn+F4 hotkey to blank and the screen the external monitor. display information on on an external the computer screen.

monitor displays information.

---------------------------------------------------------------------------

Garbled characters You are using 800 x 600 Restart your computer. If on internal display or higher resolution on simultaneous display is or flashing internal external display and desired, use 640 x 480 display when have toggled back to resolution.

connected to internal display, which external monitor. only supports 640 x 480

resolution.

---------------------------------------------------------------------------

The image on the You are using an This is typical; no external monitor external monitor and action is required.

does not fill the simultaneously screen. displaying an image on

the computer display.

---------------------------------------------------------------------------

Small red, green, or Small spots, called This is typical; no blue spots appear on on-pixels, often appear action is required.

the computer TFT on TFT screens. Compaq display. limits the number of

these on-pixels to

0.003 percent of the

approximately 1 million

transistors that are on

a 10.4-inch display.

===========================================================================

Solving Software Application Problems

Most software application or installation problems occur as a result of one or more of the following: o The application was not installed correctly.

o The CONFIG.SYS file was not configured correctly.

o Memory was not allocated correctly.

o The AUTOEXEC.BAT file was not edited correctly.

o A conflict exists between applications.

Table 2-26. Solving Software Application Problems

===========================================================================


===========================================================================

Cannot use an The application has not Run the program with the application. been added to the PATH full path name.

statement.

---------------------------------------------------------------------------

Insufficient memory System ran out of memory Check the application to run application. for the application. documentation for memory

requirements.

Install additional

memory.

Too many TSR (terminate Remove from memory any

and stay resident) TSR applications that you

applications are do not need.

running.

===========================================================================

Chapter 3 - Illustrated Parts

Introduction

This chapter provides an illustrated parts breakdown and a reference for spare part numbers for the Compaq Armada 1100 Family of Personal

Computers.

The computer combines a display assembly and system unit module. The display and system unit module are joined together by clutches on either side, which are secured by screws in the chassis and display enclosure, and which allow the display to open and close. The system unit module is secured to the CPU base by screw locks in the rear and screws in the bottom of the system unit enclosure. The display assembly is secured by screws installed in the front bezel of the display enclosure.

System Unit Module Overview

The system unit module (Figure 3-2) contains the following major components: o Hard drive - The hard drive mounts to the system chassis with a hard

drive bracket and connects directly to the system board with no

intervening cables. The hard drive bracket attaches to the hard drive

with four screws. The drive is protected by an insulator between the

system board and the drive.

o Memory expansion board - System memory can be upgraded with an optional

memory expansion board. An expansion board is added or replaced from the

bottom of the computer through the memory compartment cover. The memory

expansion board connects directly to the system board with one

connector.

o Battery pack - The nickel metal hydride battery pack is accessed through

the battery compartment.

o Integrated trackball assembly - The optical trackball is centrally

located at the bottom of the keyboard assembly. The assembly consists of

the trackball, retaining ring, and connector. The trackball assembly

connects directly to the system board and is secured by two screws.

o System board with processor - The system board is mounted directly to

the system chassis. All removable components connected to the system

board, except for the PC Card rails, EMI clip, and heatspreader must be

removed prior to removing the system board. The processor is soldered to

the system board and is not removable. It is covered by a heatspreader

designed to dissipate heat generated by the processor. There is a

bottom heatsink on the chassis, beneath the system board and the

processor. A spare parts kit containing a replacement system board comes

with the processor and heatspreader built on it. A chassis spare parts

kit includes the bottom heatsink.

o PC Card rails - The PC Card rails are replaceable and are secured by two

screws from the bottom of the system board and a clip on top of the

rails. The header attaches directly to the system board and cannot be

removed. The top and bottom PC Card ejection levers are replaceable.

o Real-Time Clock Battery - The battery is located in the left corner at

the rear of the computer.

o Diskette drive - The diskette drive attaches to the system board by a

bracket and three screws; the bracket also attaches to the heatspreader

with two screws. The drive is connected by a diskette drive cable and

LIF connector. The bracket attaches to the drive with four screws. The

drive is protected by an insulator between the system board and the

drive.

The memory expansion board and battery pack are accessed from the bottom of the computer. To service the remaining system unit module components, the keyboard assembly must be removed. A complete list of replaceable parts is included in Table 3-1.

Display Assembly Overview

All display assemblies (Figure 3-3) include the following replaceable parts: o Bezel o Enclosure latches o Liquid crystal display (LCD) panel o Shield o Enclosure o Display cable o Display ground cable o Inverter board o Clutches

The display cable is a prefolded, flex cable that connects to the display inverter board with a low insertion force (LIF) connector. The other end of the display cable is exposed at the bottom of the display enclosure and connects to the system board with a zero insertion force (ZIF) slide connector. The cable connects to the display panel directly on the CTFT model and through a crossover PCA on the CSTN models.

The display ground cable connects to the display shield on one end, and the other end clips to the flex ground bracket located above the serial port between the system board and system chassis.

The display inverter board is aligned to the right of the display enclosure with pins. One end connects to the display cable; the other end connects to the backlight cable of the LCD panel.

To replace the display assembly, the assembly must be removed from the system unit module. This is done by removing the keyboard assembly, disconnecting the display cable and display ground cable from the system unit module, removing the tilt feet and handle brackets, removing the rear clutch screws, and lifting off the display assembly.

To service display components, do not remove the display assembly from the system unit module (unless replacement of the display enclosure or clutch is required). Access display components (inverter board or latches) by removing the bezel secured with four screws on the front of the display.

System Unit Module Parts

Table 3-1. System Unit Module

===========================================================================

Description Spare Part Number Notes

===========================================================================

1. Base enclosure 262492-001 Includes:

a. PC Card eject levers and

pin

b. bottom PC Card door and

spring

c. battery latch button and

spring

d. handle bracket, screws,

and washers

e. battery shield, insulator

f. tilt foot and screws

g. battery clip

h. battery warning label *

i. lock plate *

j. label - A2860E, Service *

k. label - AY2860F,

Service *

---------------------------------------------------------------------------

2. System board Includes:

- with 75 MHz a. heatspreader plate

processor 262406-001 b. diskette drive and hard

drive insulators *

- with 100 MHz c. EMI gasket *

processor 262407-001 d. heatspreader clip *

e. heatspreader screws *

---------------------------------------------------------------------------

3. Diskette drive

bracket 189240-001

---------------------------------------------------------------------------

4. Diskette drive 147963-001 Includes:

a. label *

b. battery clip, spring,

spacer assembly *

c. sleeve, 4x4 floppy *

---------------------------------------------------------------------------

5. Real-time clock Includes Read this First

battery 117099-001 card *

---------------------------------------------------------------------------

6. Optical trackball 189197-001

---------------------------------------------------------------------------

7. PC Card ejection Includes the following:

assembly 189242-001 a. rails

b. clip

c. screws *

---------------------------------------------------------------------------

8. Chassis 262493-001 Includes:

a. bottom heatsink assembly

b. battery clip *

---------------------------------------------------------------------------

9. Clutches 147858-001 Includes:

a. Left and right clutches

b. handle bracket screws and

washers

c. tilt foot screws

---------------------------------------------------------------------------

10. Hard drive 810 MB 262468-001

---------------------------------------------------------------------------

11. Hard drive bracket 147872-001

---------------------------------------------------------------------------

12. Trough 189262-001

---------------------------------------------------------------------------

13. Left and right 189262-001 See Table 3-11 for contents

clutch ground (Miscellaneous of Miscellaneous/hardware kit

clips hardware kit)

---------------------------------------------------------------------------

14. Memory expansion

board *

8 MB 220584-001 Includes Tamper Evident

16 MB 220585-001 labels *

---------------------------------------------------------------------------

15. NiMH battery Includes Battery

pack * 190626-001 Installation card *

---------------------------------------------------------------------------

16. Screws kit *

(See Table 3-12

for contents and

where used

matrix.) 147885-001

---------------------------------------------------------------------------

* Not Shown

===========================================================================

Color STN (10.4 in) Display Assembly Parts

Table 3-2. CSTN (10.4 in) Display Assembly

===========================================================================

Spare Part

Description Number Notes

===========================================================================

1. Display bezel 189246-001

---------------------------------------------------------------------------

2. Backlight inverter Includes Caution, High

board 189135-001 Voltage label

---------------------------------------------------------------------------

3. Display panel 262466-001 Includes:

shield

display shipping box assembly,

Read This First card, and

cable depressor *

---------------------------------------------------------------------------

4. Display cables Includes:

with XOVER board 262494-001 a. display cable

b. display ground cable

c. XOVER board

---------------------------------------------------------------------------

5. Display clutch Includes screws and washers

(left and right) 147858-001 for handle bracket, and

screws for tilt feet *

---------------------------------------------------------------------------

6. Display enclosure 189245-001 Includes:

left and right latches,

springs, left and right

display clutches

logos (for Armada 1100 and

Contura 400), pad for

Sharp CSTN (for use with

Contura 400 CSTN), and

bezel screws *

---------------------------------------------------------------------------

7. Screw kit * 147885-001

(See Table 3-12

for contents and

where used matrix.)

---------------------------------------------------------------------------

* Not Shown

===========================================================================

Color TFT (10.4 in) Display Assembly Parts

Table 3-3. CTFT (10.4 in) Display Assembly

===========================================================================

Spare Part

Description Number Notes

===========================================================================

1. Display bezel 189244-001

---------------------------------------------------------------------------

2. Backlight inverter Includes Caution, High

board 189136-001 Voltage label *

---------------------------------------------------------------------------

3. Display panel 189114-001 Includes:

shield

display shipping box assembly *

---------------------------------------------------------------------------

4. Display cables 189247-001 Includes:

with XOVER board a. display cable (CTFT)

b. display ground cable

c. display cable (CSTN)

d. XOVER board for CSTN *

---------------------------------------------------------------------------

5. Display clutch Includes screws and washers

(left and right) 147858-001 for handle bracket, and screws

for tilt feet *

---------------------------------------------------------------------------

6. Display enclosure 189243-001 Includes:

left and right latches,

springs, left and right display

clutches

logos (for Armada 1100 and

Contura 400), and bezel

screws *

---------------------------------------------------------------------------

7. Screw kit * 147885-001

(See Table 3-12

for contents and

where used matrix.)

---------------------------------------------------------------------------

* Not Shown

===========================================================================

Keyboards

Table 3-4. Armada 1100 Notebook Keyboards

===========================================================================

Description All Models

===========================================================================

1. CPU cover includes: 147860-001

a. PC Card door

b. light deflector

c. spring *

---------------------------------------------------------------------------

2. U.S. 147875-001

---------------------------------------------------------------------------

3. U.K. 147875-003 *

---------------------------------------------------------------------------

4. German 147875-004 *

---------------------------------------------------------------------------

5. French 147875-005 *

---------------------------------------------------------------------------

6. Italian 147875-006 *

---------------------------------------------------------------------------

7. Spanish 147875-007 *

---------------------------------------------------------------------------

8. Danish 147875-008 *

---------------------------------------------------------------------------

9. Norwegian 147875-009 *

---------------------------------------------------------------------------

10. Swedish/Finnish 147875-010 *

---------------------------------------------------------------------------

11. Swiss 147875-011 *

---------------------------------------------------------------------------

12. French Canadian 147875-012 *

---------------------------------------------------------------------------

13. Portuguese 147875-013 *

---------------------------------------------------------------------------

14. Latin American 147875-016 *

---------------------------------------------------------------------------

15. Belgian 147875-018 *

---------------------------------------------------------------------------

16. Japanese 147875-019 *

---------------------------------------------------------------------------

17. Hangeul 147875-033 *

---------------------------------------------------------------------------

18. Brazilian 147875-035 *

---------------------------------------------------------------------------

* Not Shown

===========================================================================

Table 3-5. Optional Enhanced Keyboards

===========================================================================

Description All Models

===========================================================================

1. Enhanced III - Domestic 140536-101

2. Enhanced III - U.K. 140536-103

3. Enhanced III - German 140536-104 *

4. Enhanced III - French 140536-105 *

5. Enhanced III - Italian 140536-106 *

6. Enhanced III - Spanish 140536-107 *

7. Enhanced III - Danish 140536-108 *

8. Enhanced III - Norwegian 140536-109 *

9. Enhanced III - Swedish/Finnish 140536-110 *

10. Enhanced III - Swiss 140536-111 *

11. Enhanced III - French Canadian 140536-112 *

12. Enhanced III - Portuguese 140536-113 *

13. Enhanced III - Turkish 140536-114 *

14. Enhanced III - Greek 140536-115 *

15. Enhanced III - Latin American 140536-116 *

16. Enhanced III - Arabic 140536-117 *

17. Enhanced III - Belgian 140536-118 *

18. Enhanced III - Japanese 140536-119 *

19. Enhanced III - BHCSY ** 140536-120 *

20. Enhanced III - Hungarian 140536-121 *

21. Enhanced III - Polish 140536-122 *

22. Enhanced III - Slovakian 140536-123 *

23. Enhanced III - Russian 140536-124 *

24. Enhanced III - Czech 140536-129 *

25. Enhanced III - Thai 140536-130 *

26. Enhanced III - Beijing 140536-132 *

27. Enhanced III - Hangeul 140536-133 *

28. Enhanced III - Taipei 140536-134 *

29. Enhanced III - Brazil 140536-135 *

---------------------------------------------------------------------------

* Not Shown

** Bosnia - Herzegovina, Croatia, Slovenia, and Yugoslavia

===========================================================================

Cables

Table 3-6. Cables

===========================================================================

Description Spare Part Number

===========================================================================

1. Display cables

a. CTFT display cable 189247-001

b. CSTN display cable 189247-001, 262494-001

c. XOVER board for CSTN 189247-001, 262494-001

d. Ground cable 189247-001, 262494-001

---------------------------------------------------------------------------

2. Diskette cable 147866-001

===========================================================================

AC Adapter and Power Cord

Table 3-7. AC Adapter and Power Cord

===========================================================================

Description Spare Part Numbers

===========================================================================

1. AC adapter 147679-002

2. Power cord (U.S./Canada) 197230-001

3. Power cord (U.K.) 197232-001 *

4. Power cord (Europe) 197231-001 *

5. Power cord (Japan) 197233-001 *

6. Power cord (Australia) 197234-001 *

7. Power cord (Korea) 262488-001 *

---------------------------------------------------------------------------

* Not shown

===========================================================================

Memory Expansion Boards

Table 3-8. Memory Boards

===========================================================================


===========================================================================

Memory expansion boards

1. 8 MB 220584-001

2. 16 MB 220585-001

===========================================================================

Slipcase

Table 3-9. Slipcase

===========================================================================


===========================================================================

Slipcase 194162-001

===========================================================================

Automobile Adapter

Table 3-10. Automobile Adapter

===========================================================================


===========================================================================

Automobile Adapter 218079-001

===========================================================================

Miscellaneous CPU Kits

Table 3-11. Miscellaneous CPU Kits

===========================================================================


===========================================================================

Miscellaneous/hardware 189262-001

Includes:

Tilt feet

Trough

Battery latch

PCMCIA door

Foot shoulder screws

Battery tray assembly

Extension spring (battery eject button,

display latches)

Lock plate

Flex ground bracket

Keyboard ground clips

Left and right clutch ground clips

Handle bracket

Memory assembly door

PC Card ejection levers and pin

---------------------------------------------------------------------------

System clock battery 117099-001

---------------------------------------------------------------------------

Handle 147678-001

---------------------------------------------------------------------------

Keyboard warning labels 189288-001

---------------------------------------------------------------------------

Logos 189292-001

---------------------------------------------------------------------------

Memory door 169713-001

---------------------------------------------------------------------------

Anti-skid feet 147859-001

---------------------------------------------------------------------------

RomPaq upgrade 181088-001

---------------------------------------------------------------------------

Trackball removal tool 147779-001

---------------------------------------------------------------------------

Country kit - domestic retail 262538-001

---------------------------------------------------------------------------

Miscellaneous screws kit (See Table 3-12 for contents and where used matrix.) 147885-001

---------------------------------------------------------------------------

Shipping carton, (Quantity = 5) 262485-001

---------------------------------------------------------------------------

Shipping carton with buns, (Quantity = 1) 262486-001

===========================================================================

Computer Miscellaneous Screws Kit

Table 3-12a. Computer Miscellaneous Screws Kit Contents and Use

===========================================================================


===========================================================================

Screws and Fasteners Kit 147885-001

===========================================================================

Table 3-12b. Computer Miscellaneous Screws Kit Contents and Use

===========================================================================

Description: M2.0

Type: Fillister

Where Used: PCMCIA header

Drive: T8

Quantity Required: 2

---------------------------------------------------------------------------

Description: M2.0

Type: Fillister

Where Used: PCMCIA rails

Drive: T8


---------------------------------------------------------------------------

Description: M3.0

Type: Truss

Where Used: Heatspreader to system board

Drive: T8


---------------------------------------------------------------------------

Description: M2.5 x 5.0

Type:

Where Used: Diskette drive bracket to system board

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: PCA

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: Display assembly - internal

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: Bezel

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: Lower clutch

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: Trackball assembly to base

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: Hard drive bracket to system chassis

Drive: T8


---------------------------------------------------------------------------


Type:

Where Used: CPU cover to keyboard

Drive: SL/T8


---------------------------------------------------------------------------


Type:

Where Used: Bottom of unit

Drive: SL/T8


---------------------------------------------------------------------------

Description: M2.5

Type: Shoulder

Where Used: Handle Bracket to clutch/through CPU base

Drive: T8


---------------------------------------------------------------------------

Description: M3.0

Type: Truss

Where Used: Hard drive bracket to hard drive

Drive: T8


---------------------------------------------------------------------------

Description: M3.0

Type: Truss

Where Used: Diskette drive bracket to diskette drive

Drive: T8


---------------------------------------------------------------------------

Description: M2.6

Type: Fillister

Where Used: Diskette drive bracket to diskette drive

Drive: T8


---------------------------------------------------------------------------

Description:

Type: Screw lock

Where Used: Back of unit

Drive: 3/16" Hex


---------------------------------------------------------------------------

Description: M3.0

Type: Truss

Where Used: Panel Display

Drive: T8


---------------------------------------------------------------------------


Type: Truss

Where Used: Heatspreader to chassis

Drive: T8


===========================================================================

Documentation

Table 3-13. Documentation

===========================================================================


===========================================================================

Maintenance and Service Guide 262489-001

Illustrated Parts Map 262490-001

Armada 1100 Family Reference Guide and Quick Setup 262539-001 *

---------------------------------------------------------------------------

* To order these documents in other languages, use the following

extensions: -041 German, -051 French, -061 Italian, -101 Swedish, -331

Dutch, -081 Danish, -351 Finnish, -091 Norwegian, -161 Latin American

Spanish, -201 Brazilian Portuguese, -191 Japanese, and -AD1 Hangeul.

===========================================================================

Chapter 4 - Removal and Replacement Preliminaries

Introduction

This chapter provides general service information for the Compaq Armada

1100 Family of Personal Computers.

Adherence to the procedures and precautions described in this chapter is essential for proper service.

Electrostatic Discharge

A sudden discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry. Often the spark is neither felt or heard, but damage occurs. An electronic device exposed to electrostatic discharge (ESD) may not be affected at all and will work perfectly throughout a normal cycle. Or it may function normally for a while, then degrade in the internal layers, reducing its life expectancy.

Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.

Generating Static

Table 4-1 shows how different activities generate static electricity and at different electrostatic voltage levels.

Table 4-1. Typical Electrostatic Voltages

===========================================================================

-- Relative Humidity --

Event 10% 40% 55%

===========================================================================

Walking across carpet 35,000 V 15,000 V 7,500 V

---------------------------------------------------------------------------

Walking across vinyl floor 12,000 V 5,000 V 3,000 V

---------------------------------------------------------------------------

Motions of bench worker 6,000 V 800 V 400 V

---------------------------------------------------------------------------

Removing DIPS from plastic tubes 2,000 V 700 V 400 V

---------------------------------------------------------------------------

Removing DIPS from vinyl trays 11,500 V 4,000 V 2,000 V

---------------------------------------------------------------------------

Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V

---------------------------------------------------------------------------

Removing bubble pack from

PCBs 26,000 V 20,000 V 7,000 V

---------------------------------------------------------------------------

Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V

---------------------------------------------------------------------------

NOTE: 700 volts can degrade a product.

===========================================================================

Preventing Electrostatic Damage to Equipment

Many electronic components are sensitive to ESD. Circuitry design and structure determine the degree of sensitivity. The following proper packaging and grounding precautions are necessary to prevent damage: o Protect all electrostatic parts and assemblies with conductive or

approved containers or packaging.

o Keep electrostatic-sensitive parts in their containers until they arrive

at static-free stations.

o Place items on a grounded surface before removing them from their

container.

o Always be properly grounded when touching a sensitive component or

assembly.

o Place reusable electronic-sensitive parts from assemblies in protective

packaging or conductive foam.

Use transporters and conveyors made of antistatic belts and metal roller bushings. Mechanized equipment used for moving materials must be wired to ground and proper materials selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.

Removing Batteries

Compaq recommends that you remove all batteries from the computer before beginning the disassembly procedures. Failure to do so could cause damage to computer components.

Preventing Damage to Drives

To prevent static damage to hard drives, use the following precautions: o Handle drives gently, using static-guarding techniques.

o Store drives in the original shipping containers.

o Avoid dropping drives from any height onto any surface.

o Handle drives on surfaces that have at least one inch of shock proof

foam.

o Always place drives with the PCB assembly side down on the foam.

Grounding Methods

The method for grounding must include a wrist strap or a foot strap at a grounded workstation. When seated, wear a wrist strap connected to a grounded system. When standing, use footstraps and a grounded floor mat.

Table 4-2. Static-Shielding Protection Levels

===========================================================================

Method Voltages

===========================================================================

Antistatic Plastic 1,500

Carbon-Loaded Plastic 7,500

Metallized Laminate 15,000

===========================================================================

Grounding Workstations

To prevent static damage at the workstation, use the following precautions: o Cover the workstation with approved static-dissipative material. Provide

a wrist strap connected to the work surface and properly grounded tools

and equipment.

o Use static-dissipative mats, heel straps, or air ionizers to give added

protection.

o Handle electrostatic sensitive components, parts, and assemblies by the

case or PCB laminate. Handle them only at static-free workstations.

o Avoid contact with pins, leads, or circuitry.

o Turn off power and input signals before inserting and removing

connectors or test equipment.

o Use fixtures made of static-safe materials when fixtures must directly

contact dissipative surfaces.

o Keep work area free of non-conductive materials such as ordinary plastic

assembly aids and Styrofoam.

o Use field service tools, such as cutters, screwdrivers, vacuums, that

are conductive.

o Use a portable field service kit with a static dissipative vinyl pouch

that folds out of a work mat. Also use a wrist strap and a ground cord

for the work surface. Ground the cord to the chassis of the equipment

undergoing test or repair.

Grounding Equipment

Use the following equipment to prevent static electricity damage to the equipment:

Wrist Straps are flexible straps with a minimum of 1 megohm +/- 10% resistance to the ground cords. To provide proper ground, a strap must be worn snug against the skin. On grounded mats without banana-plug connectors, connect a wrist strap with alligator clips.

Heel straps/Toe straps/Bootstraps can be used at standing workstations and are compatible with most types of boots and shoes. On conductive floors or dissipative floor mats, use straps on both feet with a minimum of 1 megohm resistance between operator and ground. To be effective, the conductive strips must be worn in contact with the skin.

Recommended Materials and Equipment

Other materials and equipment that are recommended for use in preventing static electricity include: o Antistatic tape o Antistatic smocks, aprons, or sleeve protectors o Conductive bins and other assembly or soldering aids o Conductive foam

o Conductive table-top workstations with ground cord of 1 megohm of

resistance o Static dissipative table or floor mats with hard tie to ground o Field service kits o Static awareness labels o Wrist straps and footwear straps providing 1 megohm +/- 10% resistance o Material handling packages o Conductive plastic bags o Conductive plastic tubes o Conductive tote boxes o Metal tote boxes o Opaque shielding bags o Transparent metallized shielding bags o Transparent shielding tubes

Service Considerations

Listed below are some of the considerations that should be kept in mind during the disassembly and assembly of the computer.

Tool Requirements o Torx T-8 screwdriver o Flat-bladed screwdriver o Tool kit, Compaq part number 100767-001 (includes case utility tool,

connector removal tool, and loopback plugs) o 3/16-inch hex socket wrench o Preloaded application diskettes (Compaq Order Center, 1-800-952-7689)

Cables and Connectors

Apply only the tension required to seat or unseat the cables during insertion or removal from connectors. Handle cables by the connector or pull tabs whenever possible. In all cases, avoid bending, twisting, or tearing the cables, and ensure that cables are placed in such a way that they cannot be caught or snagged by parts being removed or replaced.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

When servicing these computers, ensure that cables are placed in their proper location during the reassembly process. Improper cable placement can cause severe damage to the unit.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Serial Number

The computer serial numbers should be provided to Compaq whenever requesting information or ordering spare parts. The serial number is located on the bottom of the CPU next to the memory compartment cover.

Chapter 5 - Computer Removal and Replacement Procedures

Introduction

This chapter provides complete removal and replacement procedures for the computer.

Serial Number

The computer serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is displayed on the bottom of the CPU, next to the memory compartment cover [1].

Disassembly Sequence Chart

Use the following chart to determine the section number and disassembly sequence for removing components from the computer.

5.3 |-- Preparing the Computer

| |--AC Adapter

| |--Diskette

| |--Battery pack

| |--PC Card

|

5.4 |-- Handle bracket

|

5.5 |-- Tilt

|

5.6 |-- Memory expansion board

|

5.7 |-- Keyboard assembly

| |-- Keyboard

| |-- CPU cover

| |-- Top PC Card (PCMCIA) door and spring

|

5.8 |-- Battery compartment components

| |-- Battery compartment

| |-- Anti-skid pad

| |-- Battery release spring and button

|

5.9 |-- Hard drive

|

5.10 |-- Real-time clock battery

|

5.11 |-- Integrated optical trackball assembly

|

5.12 |-- Diskette drive assembly

| |-- Diskette drive

| |-- Diskette drive bracket

|

5.13 |-- System board

|

5.14 |-- PC Card (PCMCIA) assembly

|

5.15 |-- PC Card ejection levers and pin

|

5.16 |-- PC Card doors and springs

|

5.17 |-- System chassis

| |-- Trough

|

5.18 |-- CPU base

| |-- Battery shield clip

| |-- Lock provision plate

| |-- Anti-skid pads

|

5.19 |-- Display assembly components

| |-- Bezel

| |-- Latches

| |-- Inverter board

|

5.20 |-- Color STN (10.4") display

| |-- LCD panel

| |-- Shield

| |-- Display cable

| |-- Display ground cable

|

5.21 |-- Color TFT (10.4") display

| |-- LCD panel

| |-- Display cable

| |-- Shield

| |-- Display ground cable

|

5.22 |-- Display enclosure

|

5.23 |-- Clutches and ground clips

Preparing the Computer

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Ensure that the power cord is disconnected from the electrical outlet and that the battery pack is removed from the computer before beginning replacement procedures. Failure to disconnect power could result in serious injury or damage to the equipment.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Static electricity can damage electronic components. Before beginning these procedures, make sure you are grounded (discharged of static electricity) by briefly touching a grounded, unpainted, metal object or surface.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Before beginning the removal and replacement procedures, follow these steps to disconnect all power to the computer and remove the diskette or PC

(PCMCIA) Card, if installed:

1. Save all files and exit all applications.

2. Turn off the computer. To turn off the computer when in Windows

applications, click Shut Down from the Start menu. When the

power/standby indicator light goes off, the computer has been

successfully shut down. In case of a severe system lock- up, when the

mouse doesn't work and Ctrl+Alt+Del is not recognized by the unit,

press Ctrl+Alt + the power button to shut down the unit. This method

can also be used if you are in DOS mode (an option chosen from the Shut

Down menu). In this instance, Shut Down is not available because

Windows isn't running.

3. Disconnect all external equipment.

4. Disconnect the AC Adapter from the electrical outlet (Figure 5-2).

5. Disconnect the AC Adapter power cord from the computer (Figure 5-3).

6. Eject the diskette (Figure 5-3).

7. Open the battery compartment by lifting up the front of the computer

[1] and sliding the battery compartment release button to the right

[2]. The battery compartment opens slightly. Lower the compartment [3]

(Figure 5-4).

8. Remove the battery pack (Figure 5-5).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Metal objects can damage the battery pack and the connectors inside the compartment. To prevent damage, do not let metal objects touch any of the connectors. Do not place any objects other than the battery pack in the battery compartment.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

9. Close the empty battery compartment.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

When installing a battery pack, do not drop it into the compartment. There are pressure sensitive contacts at the bottom of the compartment that can be damaged or crushed, resulting in intermittent charging, power, or loss of functionality. To install a battery pack, open the battery compartment, hold the unit at a 45- degree angle, and gently slide the battery pack into the compartment.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

10. Remove any installed PC Cards by pulling the top or bottom PC Card

release lever to the left to release the card. (PC Card release levers

are located on the front of the computer on the left side.) Gently

grasp the card and pull it out (Figure 5-6).

Handle Bracket

This procedure is necessary if replacing the handle bracket or if separating the display assembly from the system unit module.

Removing the Handle Bracket

To remove the handle bracket, follow these steps:

1. Turn the computer off and remove all external devices, including the

battery pack and the AC Adapter. Remove the diskette and PC Card, if

installed (Section 5.3).

2. Close the computer and turn it topside down.

3. Move the tilt foot toward the front of the computer, exposing the

handle bracket screw on either side of the computer (Figure 5-7).

4. Remove the screw and washer from each handle bracket. These screws are

not reusable and must be discarded.

5. Remove the handle bracket (Figure 5-8).

6. To install the handle bracket, reverse the previous steps. Discard the

old screws and replace with new screws.

Tilt Feet

This procedure is necessary if replacing the tilt feet or if separating the display assembly from the system unit module.

Removing the Tilt Feet

To remove the tilt feet, follow these steps:




2. Remove the tilt foot screw (Figure 5-9). Screws from the tilt feet are

not reusable and must be discarded.

3. Remove the tilt foot (Figure 5-9).

4. To install the tilt foot, reverse the previous steps. Discard the old

screws and replace with new screws.

Memory Expansion Board

This section contains removal and replacement procedures for the memory compartment cover and the memory expansion board.

The memory compartment cover and the bottom of the CPU base are embossed with arrows and two icons that indicate whether the memory compartment cover is unlocked [1] or locked [2] (Figure 5-10).

Removing and Replacing the Memory Compartment Cover

To remove the memory compartment cover, follow these steps:





3. Slide the memory compartment cover toward the rear of the computer and

lift up (Figure 5-11).

IMPORTANT: Be sure to maintain the same orientation of the cover to the

computer when removing and replacing.

4. To replace the memory compartment cover, reverse the previous steps.

Removing the Memory Expansion Board

To remove the memory expansion board, follow these steps:

1. Remove the memory compartment cover. Refer to "Removing and Replacing

the Memory Compartment Cover" in this section.

2. Press in on one of the small tabs holding the board in place [1], let

the board pop up, then pull it slightly up and out [2] (Figure 5-12).

Replacing the Memory Expansion Board

To replace the memory expansion board, follow these steps:

1. Angle in the board [1] (Figure 5-13).

2. Press down [2], so that the small tabs snap into place and hold the

board (Figure 5-13).

3. Replace the memory compartment cover. Refer to "Removing and Replacing

the Memory Compartment Cover" in this section.

Keyboard Assembly

This section contains removal and replacement procedures for the following keyboard assembly components: o CPU cover o Keyboard o Top PC Card door and spring

NOTE: The bottom PC Card door and spring are part of the CPU base.

Removing the Keyboard Assembly

To remove the keyboard assembly, follow these steps:





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Screws in the computer are not interchangeable. As you remove screws, place them with the components you removed. Damage may occur if you insert the screws in the wrong place.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

3. Remove the seven screws from the bottom of the computer (Figure 5-14).

4. Carefully turn the computer topside up and open the display to its

fully opened position (135-degree angle) (Figure 5-15).

5. Using the case utility tool, lift up the outside rear corners of the

keyboard assembly to release the keyboard snaps [1], and tilt the

keyboard assembly toward you to release the keyboard connector [2]

(Figure 5-16).

IMPORTANT: When using the case utility tool, use care to keep it out of the

diskette drive area.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer becomes top-heavy when the keyboard assembly is removed and the display is opened. To prevent damage to the display and the computer, be sure to support the computer when opening the display.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

the computer [2] (Figure 5-17).

7. Position the display to a 90-degree angle (Figure 5-18).

Removing the CPU Cover

To remove the CPU cover for replacement, follow these steps.

1. Remove the keyboard assembly from the computer. Refer to "Removing the

Keyboard Assembly" in this section.

2. Turn the keyboard assembly topside down.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Note the position of the screws removed from the bottom of the keyboard assembly. The remaining screws holes are for the screws that go through the keyboard assembly to the CPU base.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

3. Remove the seven screws on the bottom of the keyboard assembly (Figure

5-19).

IMPORTANT: There is a light deflector located in the status panel. When

removing the CPU cover from the keyboard, the light deflector

will come loose. Be sure to replace it in the status panel when

replacing the CPU cover to the keyboard.

4. Separate the CPU cover from the keyboard (Figure 5-19).

5. To replace the CPU cover, reverse the previous steps.

IMPORTANT: A set of warning labels can be ordered as a spare parts kit

(spare part number 189288-001). Install the label in the upper

right-corner of the cover. This label contains a warning message

to prevent physical discomfort and harm. Installation of this

label is essential.

Removing the Top PC Card (PCMCIA) Door and Spring

To remove the top PC Card door and spring from the keyboard assembly, follow these steps:

1. Remove the keyboard assembly from the computer. Refer to "Removing the

Keyboard Assembly" in this section.

2. Turn the keyboard assembly topside down.

3. To remove the PC Card door from the keyboard assembly, unsnap the PC

Card door [1] from the posts, and remove the door (Figure 5-20).

4. Remove the spring [2] from the PC Card door (Figure 5-20).

Replacing the Top PC Card (PCMCIA) Door and Spring

To replace the top PC Card door and spring to the keyboard assembly, follow these steps:

1. Install the PC Card spring on the door post, ensuring that the bent arm

of the spring is placed against the rib on the PC Card door (Figure

5-21).

2. Install the PC Card door, ensuring that the spring is placed between

the post [1] and the rib [2] (Figure 5-22).

Replacing the Keyboard Assembly

To install a new keyboard assembly or replace the existing keyboard assembly in the computer, follow these steps:

1. Open the display to its fully opened position of 135-degrees (Figure

5-23).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer becomes top-heavy when the keyboard assembly is removed and the display is opened. Supporting the computer with the hands when it is in the fully opened position prevents damage to the display and the computer.

Whenever hand support is removed, open the display assembly to a 90-degree angle.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

2. Angle the front end of the keyboard assembly into place at the front

edge of the system unit module.

3. Ensure that the front plastic seams of the keyboard assembly and the

front of the system unit module are aligned and flush with each other.

4. Carefully lower the rear of the keyboard assembly to the system unit

module and press the outside rear corners until the keyboard assembly

snaps into place.

5. Verify the alignment of the keyboard assembly to the computer base.

Check the seams between the front and side edges of the computer base

and the keyboard assembly. If the seam is uneven, remove the keyboard

assembly and correctly align the tabs and recesses.

6. Press firmly in the center of the keyboard assembly below the status

panel [1] to connect the keyboard connector [2] to the system board [3]

(Figure 5-24).

Battery Compartment Components

This section contains removal procedures for the following battery compartment components: o Battery compartment o Anti-skid pad o Battery release button spring o Battery release button

Removing the Battery Compartment

To remove the battery compartment components, follow these steps:




2. Turn the computer topside down.

3. Gently squeeze in the sides of the compartment, rocking it back and

forth, then lifting it up from the bottom of the base (Figure 5-25).

4. To replace the battery compartment, reverse the previous steps.

Attaching the Anti-Skid Pads

If installing a new battery compartment, two anti-skid pads must be attached to the bottom of the battery compartment. To attach the anti-skid pads, follow these steps:

1. Peel off the top layer of one of the anti-skid pads to expose the

adhesive.

2. With the adhesive-side down, place the anti-skid pad into the raised

oval outline on the battery compartment (Figure 5-26).

Removing the Battery Release Spring and Button

To remove the battery release spring and button, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer becomes top-heavy when the keyboard assembly is removed and the display is opened. To prevent damage to the display and the computer, ensure that the display assembly is opened to a 90-degree angle.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

2. Remove the keyboard assembly (Section 5.7).

3. From the battery enclosure, remove the battery release button spring by

unhooking the spring from the clip on the CPU base [1], then releasing

it from the hook on the battery release button [2] (Figure 5-27).

4. Rotate the battery release button counterclockwise, until it bows

slightly, and lift it up to clear the hook on the computer base (Figure

5-28).

5. To replace the battery release button and spring, reverse the previous

steps.

Hard Drive

This section contains removal procedures for the following hard drive components: o Hard drive o Hard drive bracket

Removing the Hard Drive

To remove the hard drive, follow these steps:





3. Remove the screw that secures the hard drive bracket to the system

4. Grasp the hard drive bracket and slide it toward the front of the

computer to disconnect the hard drive from the system board . Then lift

it up and out of the system chassis (Figure 5-30).

Removing the Hard Drive Bracket


2. Remove the hard drive and bracket. Refer to "Removing the Hard Drive" in

this section.

3. Remove the four screws from the sides of the hard drive bracket and

separate the bracket from the hard drive (Figure 5-31).

4. To replace the hard drive bracket, reverse the previous steps. For

proper alignment, replace the rear screws first.

Replacing the Hard Drive

To replace the hard drive, follow these steps:

1. Set the hard drive and bracket in place and slide it back to connector

2. Replace the screw that connects the hard drive and bracket to the

system chassis (Figure 5-33).

Real-Time Clock Battery

To remove the real-time clock battery, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Remove the real-time clock battery from the system board by inserting a

non conductive probe into the battery holder and pushing back on the

battery to release it (Figure 5-34).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Do not touch the bottom of the battery during replacement.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. To replace the real-time clock battery, reverse the previous steps.

Integrated Optical Trackball Assembly

To remove the integrated optical trackball assembly, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer becomes top-heavy when the keyboard assembly is removed and the display is opened. To prevent damage to the display and the computer, ensure that the display assembly is opened at a 90-degree angle.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Remove the screws from the front right-hand corner and the left rear

corner of the trackball assembly (Figure 5-35).

4. Disconnect the integrated optical trackball assembly from the system

board by pulling upward on the trackball assembly (Figure 5-36).

5. To replace the integrated optical trackball assembly, reverse the

previous steps.

Trackball Cleaning Procedures

1. Turn off the computer, disconnect AC power, and remove the battery

pack.

2. Remove the optical trackball.

3. Remove any large particles of debris that have fallen into the

trackball housing.

4. Dip a cotton swab in isopropyl alcohol and squeeze off excess liquid.

5. Carefully wipe inside the cage to remove residue from surfaces. Clean

the ball bearings by rubbing with the swab. Do not attempt to remove the

bearings. DO NOT USE ALCOHOL ON THE SENSOR WINDOW. Instead, gently wipe

the sensor window with a soft, dry, lint-free cloth until all debris is

removed. Allow enough time for the parts to air dry before reassembling.

6. Replace the ball and gently secure the retaining ring by rotating it

7. Replace the battery pack and reconnect the AC power.

Diskette Drive

This section contains removal and replacement procedures for the following diskette drive components: o Diskette drive o Diskette drive bracket

Removing the Diskette Drive

To remove the diskette drive, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Disconnect the diskette drive cable from the LIF connectors on the

diskette drive and the system board (Figure 5-37).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Screws in the computer are not interchangeable. As you remove screws, place them with the components you removed. Damage may occur if you insert the screws in the wrong place.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. Remove the three screws that attach the diskette drive bracket to the

system board, and the two screws that connect the bracket to the

heatspreader (Figure 5-38).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

When removing or replacing the diskette drive, hold it by grasping the vertical sides. Pressure to the front drive door area of the diskette drive will cause the drive door to pop out from the mounting.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

5. Tilt up the diskette drive bracket, then lift it up and out of the

system chassis (Figure 5-39).

Removing the Diskette Drive from the Diskette Drive Bracket

1. Remove the diskette drive from the system chassis. Refer to "Removing

the Diskette Drive" in this section.

2. Remove the diskette drive from the bracket by removing the four screws

from both sides of the bracket (Figure 5-40).

3. Separate the diskette drive from the bracket (Figure 5-41).

4. To replace the diskette drive into the bracket, reverse the previous

steps.

Replacing the Diskette Drive

To replace the diskette drive into the system chassis, follow these steps:

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

When removing or replacing the diskette drive, hold it by grasping the vertical sides. Pressure to the front drive door area of the diskette drive will cause the drive door to pop out from the mounting.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

screws to secure the diskette drive to the bracket.

NOTE: When replacing the diskette drive into the bracket, secure the front

two screws first.

2. Toe in the back end of the diskette drive into the system chassis.

IMPORTANT: Ensure that the diskette drive door does not catch on the

outside edge of the system unit module.

3. Close the diskette drive door slightly while lowering the front of the

diskette drive into the system chassis (Figure 5-42).

4. Reconnect the diskette drive cable and reinstall the five screws.

IMPORTANT: The screw order for the five screws is important. The three

screws that connect the diskette drive bracket to the system

board have a tighter tolerance than the two screws that connect

the bracket to the heatspreader; therefore, you must install the

three screws to the system board before you install the two

screws to the heatspreader.

The System Board

To remove the system board, follow these steps:

1. Turn the computer off and remove all external devices, including the battery pack and the AC Adapter Remove the diskette and PC Card if


2. Remove the memory expansion board, if installed (Section 5.6).

3. On the rear of the computer, use a 3/16 hex socket wrench to remove the

six screw locks (Figure 5-43).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


5. Remove the hard drive (Section 5.9).

6. Remove the integrated trackball assembly (Section 5.11).

7. Remove the diskette drive (Section 5.12).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The ZIF connector and its attached cable can be damaged easily. Handle only

twist the cable itself while it is seated in the ZIF connector.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

8. Disconnect the display cable from the system board by pulling up both

ends of the ZIF connector slide simultaneously [1], carefully opening

the slide [2] (Figure 5-44).

9. Lift the display cable out of the connector slide [3], being careful

not to pull or twist the cable (Figure 5-44).

10. Disconnect the display ground cable [1] from the flex ground bracket

above the serial port connector (Figure 5-45).

11. Remove the two keyboard ground clips from the chassis (Figure 5-46).

12. Remove the left clutch ground clip from the system chassis (Figure

5-47).

13. Remove the five screws from the system board and the two screws from

the battery contact (Figure 5-48).

14. From the front of the computer, tilt the system board up, then lift

the system board out of the system chassis (Figure 5-49).

At this time, remove the PCMCIA rails from the system board if you have not ordered or acquired a replacement set of rails for the new system board you are about to install. If you need to remove the rail set, refer to

"Removing the PC Card (PCMCIA) Rails" in Section 5.14.

15. Remove the flex ground bracket from above the serial port connector

between the system board and the system chassis (Figure 5-50).

16. To replace the system board, reverse the previous steps.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

When returning a system board for repair or when replacing a board, be careful that the contacts on the EMI clip do not become bent or otherwise damaged.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

IMPORTANT: When replacing the system board, the screws must be replaced as

follows:

1. Install screws [1] and [2] on the system board before replacing the

remaining system board and battery contact screws (Figure 5-52).

PC Card (PCMCIA) Assembly

The PC Card assembly consists of the PC Card clip and PC Card rails. To remove the PC Card assembly or to remove part of the assembly, follow the steps below.

Removing the PC Card Clip

To remove the PC Card clip, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Remove the system board (Section 5.13).

4. Remove the two screws of the PC Card rails from the bottom of the system

board (Figure 5-53).

5. Remove the clip from the top of the PC Card (PCMCIA) header (Figure

5-53).

6. To replace the PC Card clip, reverse the previous steps.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Do not over tighten the clip, or it can become damaged.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Be sure not to overtighten any screws or the PC Cards may be difficult to insert and eject.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Removing the PC Card (PCMCIA) Rails

To remove the PC Card rails, follow these steps.

1. Remove the PC Card clip. Refer to "Removing the PC Card Clip" in this

section.

2. Using the connector removal tool, compress the set of clips on the

right and left sides of the rails. This allows the rails to be shifted

right or left for removal.

3. Slide the rails out of the header (Figure 5-54).

4. To replace the PC Card rails, reverse the previous steps. The PC Card

rails go under the edge of the header.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Be sure not to overtighten any screws or the PC Cards may be difficult to insert and eject.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

PC Card (PCMCIA) Ejection Levers and Pin

This section contains removal and replacement procedures for the PC Card ejection levers and pin.

To remove the PC Card ejection levers and pin, follow these steps:

1. Turn the computer off and remove all external devices, including the battery pack and the AC Adapter Remove the diskette and PC Card if



3. Remove the PC Card ejection lever pin from the system chassis (Figure

5-55).

4. Remove the top PC Card ejection lever (Figure 5-56).

5. Remove the bottom PC Card ejection lever from the boss on the CPU base

Figure 5-57).

6. To replace the PC Card ejection levers and pin, reverse the previous

steps.

PC Card (PCMCIA) Doors and Springs

This section contains removal and replacement procedures for the PC Card doors and springs. The top PC Card door and spring are located on the keyboard assembly and the bottom PC Card door and spring are located on the

CPU base.

Top PC Card Door and Spring

To remove the top PC Card door and spring, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Unsnap the PC Card door [1] from the post and remove the door (Figure

5-58).


To replace the top PC Card door and spring, follow these steps:

1. Install the PC Card spring on the door rib, making sure the bent arm of

the spring is placed against the rib on the PC Card door (Figure 5-59).

2. Install the PC Card door, making sure the spring is placed between the

notch [1] and the rib [2] (Figure 5-60).

Bottom PC Card (PCMCIA) Door and Spring

The bottom PC Card door and spring are located on the CPU base. To remove the bottom PC Card door and spring, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Unsnap the PC Card door from the post and remove the door [1] (Figure

5-61).


To replace the bottom PC Card spring and door, follow these steps:

1. Install the PC Card spring on the door post, making sure the bent arm

of the spring is placed against the rib on the PC Card door (Figure

5-62).

2. Install the PC Card door, making sure the spring is placed between the

notch [1] and the rib [2] (Figure 5-63).

System Chassis

To remove the system chassis, follow these steps:




2. Remove the handle bracket on either side of the computer (Section 5.4).

3. Remove the tilt feet on either side of the computer (Section 5.5).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


5. Remove the system board (Section 5.13).

6. Close the display.

7. Remove the four clutch screws from the rear of the system unit module

(Figure 5-64).

8. Remove the display assembly from the system unit module (Figure 5-65).

9. Slide the trough at the rear of the CPU base to the right, then lift up

to remove (Figure 5-66).

10. Remove the PC Card ejection levers and pin (Section 5.15).

11. Remove the system chassis by gently separating it from the CPU base and

lifting out the system chassis (Figure 5-67).

12. To replace the system chassis, reverse the previous steps, being sure

to achieve proper alignment by fitting the two slots in the chassis

over the two small steps on the CPU base.

CPU Base

This section provides removal and replacement procedures for the following

CPU base components: o Battery shield clip o Lock provision plate o Anti-skid pads

Removing and Replacing the Battery Shield Clip

To remove the battery shield clip, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Remove the battery spring clip.

4. Remove the battery shield clip located between the battery enclosure and

the right interior wall of the CPU base (Figure 5-68).

5. To replace the battery shield clip, reverse the previous steps.

Removing and Replacing the Lock Provision Plate

To remove the lock provision plate, follow these steps:




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


3. Remove the lock provision plate located between the battery enclosure

and the right interior wall of the CPU base (Figure 5-69).

4. To replace the lock provision plate, reverse the previous steps.

Attaching the Anti-Skid Pads

If replacing the CPU base, two anti-skid pads for the battery tray and the two for the CPU base must be attached to the bottom of the base. To attach the anti-skid pads, follow these steps:

1. Peel off the top layer of one of the anti-skid pads to expose the

adhesive.

2. With the adhesive side down, place the anti-skid pad into the raised

oval outline on the CPU base and the battery tray (Figure 5-70).

Display Assembly Components

This section contains removal and replacement procedures for the following display assembly components:

o Bezel o Latches o Inverter board

Removing and Replacing the Display Bezel

To remove the display bezel, follow these steps:




2. Open the computer.

3. Remove the four screws from the display bezel (Figure 5-71).

4. Tilt the display to approximately a 110-degree angle.

5. Using the case utility tool, separate the display bezel from the display

assembly (Figure 5-72).

6. To replace the bezel, reverse the previous steps.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The unit can become top-heavy when pressure is applied while replacing the bezel. Supporting the unit with your hands will prevent it from falling over.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Removing the Display Enclosure Latches and Springs

To remove the display enclosure latches and springs from either side of the display enclosure, follow these steps:





3. Remove the display bezel. Refer to "Removing and Replacing the Display

Bezel" in this section.

4. Hold the bottom of the latch near the spring. Flex the hook end of the

display latch away from the display enclosure [1] (Figure 5-73).

5. Pull the display latch from the top, then out of the display enclosure

[2] (Figure 5-73).

6. Remove the display latch spring from the latch (Figure 5-74).

Replacing the Display Enclosure Springs and Latches

To replace the display springs and latches, follow these steps:

1. Hook the display latch spring on to the display latch [1] and place the

display latch spring over the post in the display enclosure [2] (Figure

5-75).

2. Slide the display latch into place on either side of the display

enclosure (Figure 5-76).

Removing the Display Inverter Board from the CSTN (10.4 in) Display

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To remove the inverter board from the CSTN display, follow these steps:







>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

When servicing the computer, ensure that cables are placed in their proper location to avoid pinching during the reassembly process. Improper cable placement can cause severe damage to the unit.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. Lift up the inverter board until it clears the three posts on the

display enclosure (Figure 5-77).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

5. Unplug the backlight cable [1] from the display inverter board to free

the inverter board from the display enclosure (Figure 5-78).

6. Remove the display cable [2] from the inverter board by gently lifting

up the inverter board and disconnecting it from the display cable and

the display enclosure (Figure 5-78).

7. Remove the screw in the lower-right corner of the display to release the

ground wire which is attached to the inverter board.

Removing the Display Inverter Board from the CTFT (10.4 in) Display

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

NOTE: The inverter board for the CTFT (10.4 in) display fits partially

behind the display. Loosen the screws (as indicated by the circles in

Figure 5-79) on the display to slide the inverter out from behind the

display.

To remove the inverter board for the CTFT (10.4 in) Display, follow these steps:







>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. Lift up the inverter board until it clears the three posts on the

display enclosure (Figure 5-80).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Ensure that the power cord is disconnected from the electrical outlet and

replacement procedures. Failure to disconnect power could result in serious injury or damage to the equipment.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

5. Unplug the backlight cable [1] from the display inverter board to free

the inverter board from the display enclosure (Figure 5-81).

6. Remove the display cable [2] from the inverter board by gently lifting

up the inverter board and disconnecting it from the display cable and


Replacing the Display Inverter Board

To replace the inverter board, follow these steps:

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< h b f ll d h l i i h

These steps must be followed whenever replacing any component in the display assembly because of high susceptibility to electrostatic discharge, which will damage the LCD panel.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

1. Insert the inverter board LIF connector into the display cable.

2. Plug in the backlight cable to the inverter board.

3. Mount the inverter board into the display enclosure, aligning the

inverter board with the three mounting posts.

4. For the CSTN (10.4 in) display, reconnect the inverter ground wire to

the lower right corner of the display.

5. For the CTFT (10.4 in) display, the inverter board slides partially

underneath the display.

Color STN (10.4 in) Display

This section contains removal and replacement procedures for the following

CSTN (10.4 in) display components: o Display panel o Shield o Display cable o Display ground cable

Removing the CSTN (10.4 in) Panel, Shield, Display Cable, and the Display

Ground Cable

To remove the liquid crystal display CSTN (10.4 in) panel, shield, display cable, and the display ground cable, follow these steps:





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The ZIF connector and its attached cable can be damaged easily. Handle only the connector slide when disconnecting the ZIF connector. Never pull or twist the cable itself while it is seated in the ZIF connector.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. Remove the display cable from the system board by pulling up both ends

of the ZIF connector slide simultaneously [1], carefully opening the

slide [2] (Figure 5-82).




above the serial port connector (Figure 5-83).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To prevent damage to the trough, ensure that the trough does not tilt forward into the CPU base when the bezel is removed.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

7. Remove the display bezel (Section 5.19).

8. Remove the inverter board (Section 5.19).

9. Remove the display cable and backlight cable from the inverter board

(Section 5.19).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer becomes top-heavy when the keyboard assembly is removed and the display is opened. To prevent damage to the display and the computer, be sure to support the display assembly when it is fully opened at approximately a 135-degree angle.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

10. Open the display to its fully open position of approximately

135-degrees (Figure 5-84).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

11. Remove the screws that secure the CSTN (10.4 in) panel and shield to


12. Carefully remove the CSTN (10.4 in) panel, display cable, and shield

from the display enclosure (Figure 5-86).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Excess flexing and bending of the shield tabs and fingers can damage the shield.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

13. On the right side of the display shield, slide the two shield tabs

from the face of the CSTN (10.4 in) panel to the back (Figure 5-87).

14. Lay the CSTN (10.4 in) panel face down on a clean surface.

15. Slide the display shield off the panel (Figure 5-88).

16. Disconnect the display cable from the connector on the back of the

CSTN (10.4 in) panel (Figure 5-89).

17. Lift the display ground cable out of the display enclosure (Figure

5-90).

Replacing the Display Ground Cable, Display Cable, Shield, and the CSTN

(10.4 in) Panel

To replace the display ground cable, display cable, shield, and the CSTN

(10.4 in) panel, follow these steps:

1. Position the display ground cable in the display enclosure, aligning

the cable with the bosses in the display enclosure (Figure 5-91).

2. Connect the display cable to the XOVER Board. Then connect the XOVER

Board to the connector on the back of the panel (Figure 5-92).

3. Slightly lift the tabs on the left side of the display shield and slide

the shield onto the CSTN (10.4 in) panel. Ensure that the LIF connector

end of the display cable is exposed on the right side of the panel

(Figure 5-93).

4. Place the display shield tabs in the indentations on the sides of the

CSTN (10.4 in) panel (Figure 5-94).

5. Align the CSTN (10.4 in) panel, display cable, and shield in the

display enclosure and replace the screws. Before replacing the screw in

the lower-left corner, route the XOVER board ground wire around the

boss at the bottom of the display enclosure. Hold the end of the wire

over the screw hole and install the screw, attaching the wire. Ensure

that the ZIF connector end of the display cable and the end of the

display ground cable are exposed at the bottom of the display enclosure

(Figure 5-95).

6. Connect the display cable and the backlight cable to the inverter board

(Section 5.19).

7. Replace the inverter board (Section 5.19).

8. Replace the bezel (Section 5.19).

9. Connect the display ground cable [1] to the flex ground bracket above

the serial port connector (Figure 5-96).

10. Carefully insert the end of the display ground cable into the ZIF

connector slide on the system board.

IMPORTANT: Ensure that the ZIF connector slide is in its fully upward

position and that it remains so while you are inserting the

cable into it. Before closing the slide, ensure that the cable

is fully seated (to the white insertion line) in the ZIF

connector.

11. While holding the end of the display cable inside the ZIF connector

slide, press down both ends of the slide simultaneously to secure the

cable in the ZIF connector (Figure 5-97).

12. Ensure that the cable has been seated evenly and that the white line

on the cable is level.

13. Replace the keyboard assembly (Section 5.7).

Color TFT (10.4 in) Display

This section contains removal and replacement procedures for the following

CTFT (10.4 in) display components:

o Display panel o Display cable o Shield o Display ground cable

Removing the CTFT (10.4 in) Display Panel

To remove the CTFT (10.4 in) panel, follow these steps:





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

The computer becomes top-heavy when the keyboard assembly is removed and the display is opened. To prevent damage to the display and the computer, be sure to support the display assembly when it is fully opened at approximately a 135-degree angle.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. Open the display to its fully open position of approximately 135

degrees (Figure 5-98).

NOTE: The inverter board of the CTFT (10.4 in) display fits partially

behind the display. Loosen the screws on the display to slide the

inverter out from behind the display.



(Section 5.19).

7. Remove the four screws that secure the panel to the display enclosure

(Figure 5-99).

8. Carefully rotate the CTFT (10.4 in) panel down and out of the display

5-100).

9. Remove the display cable from the connector on the back of the panel

by pulling upward on the tabs on the back of the connector (Figure

5-101).

10. The CTFT display cable is disconnected by pulling upward on the tabs

on the back of the connector.

Replacing the CTFT (10.4 in) Display Panel

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To replace the CTFT (10.4 in) panel, follow these steps:

1. Connect the display cable to the connector on the back of the CTFT

(10.4 in) panel (Figure 5-102).

NOTE: A replacement panel has a diaper, or shield, preinstalled on the

back. The panel may be installed optionally on either a Contura 400

or Armada 1100 CTFT display.

2. Position the CTFT (10.4 in) panel into the display enclosure, ensuring

that the ZIF connector end of the display cable is exposed on the

right side of the panel (Figure 5-103).

3. Secure the CTFT (10.4 in) panel with four screws to the display

enclosure.

Removing the CTFT (10.4 in) Display Cable

To remove the CTFT (10.4 in) display cable, follow these steps:





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To prevent damage to the trough, ensure that the trough does not tilt forward into the CPU base when the bezel is removed

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

4. Remove the display cable from the system board by pulling up both ends

of the ZIF connector slide simultaneously [1], carefully opening the

slide [2] (Figure 5-104).





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


(Section 5.19).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

9. Remove the display panel. Refer to "Removing the CTFT (10.4 in)

Display Panel" in this section.

10. Disconnect the display cable. Refer to "Removing the CTFT (10.4 in)

Display Panel" in this section.

Replacing the CTFT Display Cable

To replace the CTFT (10.4 in) display cable, follow these steps:

1. Connect the display cable to the (10.4 in) panel. Refer to "Replacing

the CTFT (10.4 in) Display Panel" in this section.

2. Connect the display cable and the backlight cable to the inverter board

(Section 5.19).



5. Carefully insert the end of the display cable into the ZIF connector

slide on the system board.





connector.


slide, press down both ends of the slide simultaneously to secure the


7. Ensure that the cable has been seated evenly and that the white line on

the cable is level.


Removing and Replacing the CTFT (10.4 in) Display Shield

To remove the CTFT (10.4 in) display shield, follow these steps:





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<




(Section 5.19).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

6. Remove the panel from the display enclosure. Refer to "Removing the

CTFT (10.4 in) Display Panel" in this section.

7. Remove the remaining screws from the display shield (Figure 5-106).

8. Lift the display shield up and away from the display enclosure (Figure

5-107).

9. To replace the display shield, reverse the previous steps.

Removing and Replacing the Display Ground Cable

To remove the display ground cable, follow these steps:





>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<




(Section 5.19).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

6. Remove the panel from the display enclosure. Refer to "Removing the

CTFT (10.4 in) Display Panel" in this section.

7. Remove the display cable. Refer to "Removing the CTFT (10.4 in) Display

Cable" in this section.

8. Remove the display shield. Refer to "Removing and Replacing the CTFT

(10.4 in) Display Shield" in this section.


above the serial port connector on the system unit module (Figure

5-108).

10. Lift the display ground cable out of the display enclosure (Figure

5-109).

11. To replace the display ground cable, reverse the previous steps.

Display Enclosure

This section provides replacement procedures for the display enclosure.

Replacing the Display Enclosure

To replace the display enclosure, follow these steps:




2. Remove the handle brackets (Section 5.4).

3. Remove the tilt feet (Section 5.5).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


5. Remove the right clutch ground clip located between the clutch and the

CPU base (Figure 5-110).

6. Lift up both ends of the ZIF connector slide simultaneously [1],

carefully opening the slide [2] (Figure 5-111).




(Figure 5-112).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

To prevent damage to the display assembly while the keyboard assembly is removed from the system unit module, use care when closing the display.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

9. Gently lower the display.

10. Remove the four clutch screws on the rear of the system unit module

(Figure 5-113).

11. Lift the display assembly off the system unit module (Figure 5-114).

12. Position the display assembly topside up.


14. Remove the display latches and springs (Section 5.19).


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


(Section 5.19).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

17. Remove the LCD panel, the display cable, the shield, and the display

ground cable from the display enclosure as follows:

o If removing a CSTN (10.4 in) panel and shield, refer to Section

5.20.

o If removing a CTFT (10.4 in) panel and shield, refer to Section

5.21.

18. Remove the display clutches from the display enclosure (Figure 5-115).

19. Place the new display enclosure topside up.

20. Replace the display clutches on either side of the display enclosure

(Figure 5-116).

21. Replace the display ground cable, the LCD panel, the shield, and the

display cable into the display enclosure as follows:

o If replacing a CSTN (10.4 in) panel and shield, refer to Section

5.20.

o If replacing a CTFT (10.4 in) panel and shield, refer to Section

5.21.

22. Connect the display cable and backlight cable to the inverter board

(Section 5.19).


24. Replace the display latches and springs (Section 5.19).


26. Position the display clutches at a 90-degree angle (Figure 5-117).

27. Align the clutches with the system unit module, ensuring that the

display ground cable and the display cable are positioned on top of

the system unit module (Figure 5-118).

28. Replace the four rear clutch screws (Figure 5-119).

29. Open the display to a 90-degree angle (Figure 5-120).

30. Connect the display ground cable [1] to the flex ground bracket above

the serial port connector between the system board and the system

chassis (Figure 5-121).

31. Carefully insert the end of the cable into the ZIF connector slide on

the system unit.





connector.



33. Ensure that the cable has been seated evenly and that the white line

on the cable is level.

34. Replace the right clutch ground clip located between the clutch and

the CPU base (Figure 5-123).


36. Replace the tilt feet (Section 5.5).

37. Replace the handle bracket (Section 5.4).

Clutches and Ground Clips

This section contains removal and replacement procedures for the clutch ground clips located between the system chassis and CPU base, and for the clutches that join the system unit module and the display enclosure.

Removing and Replacing the Clutch Ground Clips

To remove the left and right clutch ground clips, follow these steps:





3. Remove the left clutch ground clip from the system chassis (Figure

5-124).

4. Remove the right clutch ground clip located between the clutch and the

CPU base (Figure 5-125).

5. To replace the clutch ground clips, reverse the previous steps.

Removing and Replacing the Clutches

To remove the clutches, follow these steps:




2. Remove the handle brackets from each side of the computer (Section

5.4).

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


5. Remove the left and right clutch ground clips (see "Removing and

Replacing the Clutch Ground Clips" in this section).

6. Pull up both ends of the ZIF connector slide simultaneously [1],

carefully opening the slide [2] (Figure 5-126).



8. Remove the display ground cable [1] away from the flex ground bracket

(Figure 5-127).

9. Using a Torx T8 or slotted driver, remove the four clutch screws on the

rear of the system unit module (Figure 5-128).

10. Lift the display assembly off the system unit module (Figure 5-129).

11. Place the display assembly topside up.


13. Remove the screws from the clutches on either side of the display

enclosure.

14. On either side of the display enclosure, slide the clutches from

underneath the display shield tabs (Figure 5-130).

15. Slide the clutches out of the display enclosure.

16. To replace the clutches, reverse the previous steps.

IMPORTANT: When replacing the display clutch screws, ensure proper

alignment of the display clutches on either side of the display

enclosure with the shield (Figure 5-131).

Chapter 6 - Compaq Utilities

Introduction

This chapter describes Computer Setup, a Compaq utility that can be helpful when servicing the Compaq Armada 1100 Family of Personal

Computers.

Computer Setup

Computer Setup automatically recognizes and configures the system for new

Compaq devices. It does this without prompting you for information about the devices. However, if you add a memory expansion board, a prompt appears the next time you turn on the computer, notifying you of the new memory configuration.

You can run Computer Setup to view or to change the current configuration settings. Run Computer Setup when you first turn on the computer by pressing F10 when the prompt appears on the screen.

The first Computer Setup screen displays current settings for the system, ports, and devices. The status bar at the bottom of the screen gives instructions for navigating and choosing options. The status bar also displays descriptions as you highlight menus and menu options.

NOTE: If the main system board is replaced, the serial number on this

screen will change to 0 (zero).

Select one of the menus from the menu bar at the top of the screen to view or to change the following configuration settings: o Initialization, which sets startup preferences o Ports, including serial and parallel o Power, including power management and Hibernation o Security, including setup and power-on passwords and device disabling

Initialization Menu

Select the Initialization menu to change the initialization (startup) settings for running the POST memory tests, numlock on or off, the drive boot sequence, and the active display.

Ports Menu

Select the Ports menu to change the default input/output (I/O) addresses and interrupt requests (IRQs) for serial and parallel ports.

NOTE: If you select conflicting settings for the ports, the system will

automatically change one of the settings.

Power Menu

Select the Power menu to enable or disable Power Management, low-battery warning beeps, and an external energy saving monitor. The factory default settings are Power Management Enabled While on Battery, Conservation Level

Medium, Low-Battery Warning Beeps Enabled, and External Energy Saving

Monitor Disabled.

If you select to disable the low-battery warning beeps, a low-battery condition will be indicated only by a blinking battery light. If you disable Power Management or Hibernation, information in memory will not be automatically saved during a critical low-battery condition.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

If you disable Power Management or Hibernation, you must take immediate action to resolve a low-battery condition to prevent losing unsaved information.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

If you enable the selection for an external energy saving monitor, it will enter low-power mode when the screen timeout occurs. If you enable this selection and you do not have an energy saving monitor, the screen display may become distorted.

Power Management

Under Power Management, you can select whether to enable Power Management while on AC or battery, only while on battery, or never (disabled).

If you enable Power Management, you can select the conservation level: high, medium, none (drain), or custom. The conservation level sets the timeouts for Standby, Hibernation, drives, and screens.

A timeout is a period of inactivity after which power is turned off to the system or component.

o High: Provides the maximum amount of power conservation and the maximum

battery operating time from a single charge.

o Medium (default): Provides a balance between performance and battery

life.

o Custom: Conserves power according to specified timeout settings.

o None (Drain): Provides no conservation features; use to drain the

battery pack.

Security Menu

Select the Security menu to set, change, or delete the setup and power-on passwords, and to enable/disable QuickLock/QuickBlank, power-on password from Standby, diskette drives, diskette drive boot ability, ports, and PC

Card slots.

Setup Password

The Setup password protects the system configuration from unauthorized changes. After establishing a setup password, you cannot change the system configuration until you enter the setup password.




The next time you run Computer Setup, you are prompted to enter the password. If you enter the password incorrectly, you are prompted to reenter the password.

If you forget the setup password, you cannot change the system configuration until the computer memory is cleared of the password. Refer to Section 2.2 in this guide for procedures for clearing the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Record your setup password and put it in a safe place. If you forget your setup password, you cannot reconfigure the computer until the computer memory is cleared of the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Power-On Password

The power-on password prevents use of the computer until the password is entered. After you establish the power-on password, you must enter it whenever you turn on the computer.




You can also select to require the power-on password when exiting Standby.

The next time you start the computer (or exit Standby), you are prompted to enter the password. If you enter the password incorrectly, you are prompted to reenter the password.

If you forget your power-on password, you cannot use the computer until the computer memory is cleared of the password. Refer to Section 2.2 in this guide for procedures for clearing the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Record your power-on password and put it in a safe place. If you forget your power-on password, you cannot use the computer until the computer memory is cleared of the password.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

QuickLock/QuickBlank

Enabling QuickLock/QuickBlank allows you to temporarily disable the keyboard and blank the screen until the power-on password is entered.

After you have enabled QuickLock/QuickBlank, you can initiate it at any time by pressing the hotkey Fn+F6.

When QuickLock/QuickBlank is initiated, the key icon on the status panel turns on. Type your power-on password on the blank screen to exit

QuickLock/QuickBlank.

Disabling Devices

The Security Menu provides a way to disable the following devices: o Serial port o Parallel port o PC Card slots o Diskette drive

o Diskette drive boot ability

Disabling these devices prevents the unauthorized transfer of data using the devices. To reenable a device, deselect the Disable option and restart the computer.

Exit Menu

The Exit menu has four options: o Save and Exit: Saves configuration changes, but some changes do not take

effect until the computer is restarted.

o Save and Reboot: The computer reboots and all configuration changes take

effect.

o Exit (No Save): Exits and does not save the changes you have made.

o Restore Factory Defaults: Replaces the current configuration settings

with the original factory default settings.

Chapter 7 - Specifications

Introduction

This chapter provides physical and performance specifications for the following: o Computer o Display o Hard drives o Diskette drive o Battery pack o External power sources

The chapter also includes: o System interrupts o System DMA o System I/O address o System memory map

Computer

Table 7-1. Computer Specifications

===========================================================================

U.S. Metric

===========================================================================

Dimensions:

10.4" Color STN 8.9" x 11.9" x 2.25" 22.61cm x 30.23 x 5.72cm

10.4" Color TFT 8.9" x 11.9" x 2.25" 22.61cm x 30.23 x 5.72cm

---------------------------------------------------------------------------

Weight

(w/o battery):

10.4" Color STN 5.0 lbs 2.25 kg

10.4" Color TFT 5.0 lbs 2.25 kg

---------------------------------------------------------------------------

Weight (w/battery):

10.4" Color STN 6.1 lbs 2.75 kg

10.4" Color TFT 6.1 lbs 2.75 kg

---------------------------------------------------------------------------

Stand-Alone (Battery)

Power Requirements:

Nominal Operating

Voltage 10.8 V

Nominal Operating 12.0 W

Peak Operating 15.0 W

---------------------------------------------------------------------------

Environmental Requirements:

Temperatures

Operating 50oF to 95oF 10oC to 35oC

Nonoperating -4oF to 140oF -20oC to 60oC

---------------------------------------------------------------------------


Relative Humidity

Operating 10% to 90% 10% to 90%

Nonoperating 5% to 95% 5% to 95%

===========================================================================

Displays

Table 7-2. Color STN (10.4 in) VGA Display

===========================================================================

U.S. Metric

===========================================================================

Dimensions

(display size):

Height 6.3 in 16.0 cm

Width 8.4 in 21.3 cm

---------------------------------------------------------------------------

Number of Colors 256

---------------------------------------------------------------------------

Color Palette 256 K

---------------------------------------------------------------------------

Contrast Ratio 20:1

---------------------------------------------------------------------------

Brightness 90 NIT

---------------------------------------------------------------------------

Refresh Rate 60 Hz

---------------------------------------------------------------------------

Pixel Resolution

Pitch 0.33 x 0.33 mm

Format 640 x 480

Configuration RGB Stripe

---------------------------------------------------------------------------

Backlight CCFT Edge-Lit at the Top

---------------------------------------------------------------------------

Inverter

Input voltage +5Vdc, 10 - 18 Vdc

Ouput voltage 500Vac

Max input power 3.2W

Max output power 2.6W

---------------------------------------------------------------------------

Character Display 80 x 25

---------------------------------------------------------------------------

Total Power

Consumption 4 W (Maximum)

===========================================================================

Table 7-3. Color TFT (10.4 in) VGA Display

===========================================================================

U.S. Metric

===========================================================================

Dimensions

(display size)



---------------------------------------------------------------------------

Number of Colors 256

---------------------------------------------------------------------------

Color Palette 256 K

---------------------------------------------------------------------------

Contrast Ratio 100:1

---------------------------------------------------------------------------

Brightness 90 NIT

---------------------------------------------------------------------------

Refresh Rate 60 Hz

---------------------------------------------------------------------------

Pixel Resolution

Pitch 0.33 x 0.33 mm

Format 640 x 480

Configuration RGB Stripe

---------------------------------------------------------------------------

Backlight CCFT Edge-Lit at the Top

80 x 25

+5Vdc, 10 - 18 Vdc

500Vac

3.2W

2.6W

---------------------------------------------------------------------------

Total Power

Consumption 4 W (Maximum)

===========================================================================

Hard Drive

Table 7-4. Hard Drive Specifications

===========================================================================

Model Standard Configurations 810 MB

===========================================================================

Formatted Capacity per Drive (MB):

Physical 815.9

Logical 814.9

---------------------------------------------------------------------------

Drive Type 65

---------------------------------------------------------------------------

Drive Size:

Inches 4.0 x 2.5 x .5

Millimeters 102 x 70 x 12.7

---------------------------------------------------------------------------

Transfer Rate:

Media (Mb/s) 27.4 to 54

Interface (MB/s) Up to 16.7

---------------------------------------------------------------------------

Sector Interleave 1:1

---------------------------------------------------------------------------

Typical Seek Time

(including settling):

Single Track (ms) 4

Average (ms) 15

Full Stroke (ms) 24

---------------------------------------------------------------------------

Disk Rotational Speed

(RPM) 3634

---------------------------------------------------------------------------

Physical Configuration:

Cylinders 3915

Data Heads 3

Sectors/Track 90-180

Bytes/Sector 512

---------------------------------------------------------------------------

Logical Configuration:

Cylinders 1579

Data Heads 16

Sectors/Track 63

Bytes/Sector 512

---------------------------------------------------------------------------

Buffer Size (KB) 128

===========================================================================

Diskette Drive

Table 7-5. Diskette Drive Specifications

===========================================================================

Diskettes:

Size 3.5 in (8.9 cm)

High Density (MB) 1.44

Low Density (KB) 720

---------------------------------------------------------------------------

Light Green

---------------------------------------------------------------------------

Height One-third

---------------------------------------------------------------------------

Bytes per Sector 512

---------------------------------------------------------------------------

Sectors per Track:

High Density 18

Low Density 9

---------------------------------------------------------------------------

Tracks per Side:

High Density 80

Low Density 80

---------------------------------------------------------------------------

Read/Write Heads 2

---------------------------------------------------------------------------

Average Access Time (ms):

Track-to-Track (high/low) 3/3

Average (high/low) 94/94

Settling Time (ms) 15

Latency Average (ms) 100

===========================================================================

Battery Pack

Table 7-6. Nickel Metal Hydride Battery Pack

===========================================================================

U.S. Metric

===========================================================================

Dimensions:


Length 8.07 in 20.5 cm


---------------------------------------------------------------------------

Weight 1.09 lb 0.495 Kg

---------------------------------------------------------------------------

Energy:

Nominal Open Circuit Voltage 10.8 V dc

Rated Capacity 2400 mAh

Standard Recharge Rate 27 W Maximum

7 W Minimum

---------------------------------------------------------------------------


Operating temperatures 50oF to 104oF 10oC to 40oC

Storage temperatures

No time limit -4oF to 86oF -20oC to 30oC

Not longer than 3 months -4oF to 104oF -20oC to 40oC

Not longer than 1 month -4oF to 122oF -20oC to 50oC

===========================================================================

External Power Sources

Table 7-7. AC Adapter

===========================================================================

AC Adapter Power Supply Ratings

Rated Voltage Range 100-120/220-240 V

Rated Input Current 0.8/0.4 Amp

Rated Input Frequency 50 - 60 Hz

Maximum Output Voltage 16.5 V dc

Maximum Output Current 2.6 Amp

Maximum Output Power 27 W

===========================================================================

Table 7-8. Automobile Adapter

===========================================================================

Auto Adapter Power Supply Ratings

Power Supply (Input)

Nominal Voltage 13.8 VDC

Operating Voltage 10.5 - 14.8 VDC

Maximum Voltage 16.0 VDC

Input Fuse Protection 8.0 A

Power Supply (Output)

Nominal Voltage 120 VAC

Load Regulated Voltage 108 - 125 VAC

Line Regulated Voltage 105 to 125 VAC

Output Frequency 60 Hz +/- 3 Hz

Output Overload Protection 150W @ 2 sec.

===========================================================================

System Interrupts

Table 7-9

===========================================================================

Hardware IRQ System Function

===========================================================================

IRQ0 Timer interrupt

IRQ1 Keyboard

IRQ2 Interrupt controller cascade

IRQ3 COM 2 - used by MSIO or PCMCIA controller

IRQ4 COM 1 - used by MSIO or PCMCIA controller

IRQ5 Available for use

IRQ6 Diskette Drive controller


IRQ8 Real-Time Clock (MSIO)




IRQ12 Mouse

IRQ13 Floating point error input

IRQ14 Hard Drive

IRQ15

IRQA EPP parallel port

===========================================================================

System DMA

Table 7-10

===========================================================================

Hardware DMA System Function

===========================================================================

DMA 0/A (mappable) Not assigned

DMA 1/B PCMCIA controller

DMA 2 Diskette drive controller

DMA 3 EPP parallel port

DMA 4 Not assigned

DMA 5 Not assigned

DMA 6 Not assigned

DMA 7 Not assigned

---------------------------------------------------------------------------

NOTE: PC Card controller can use DMA 1, 2, or 5.

===========================================================================

System I/O Address

Table 7-11

===========================================================================

I/O Address (Hex) System Function (Shipping Configuration)

===========================================================================

000 - 00F Master DMA Controller # 1

010 - 011 Unused

012 - 01F Unused

020 - 021 Peripheral Interrupt Controller # 1

022 - 024 Opti Chipset Configuration Registers

025 - 03F Unused

040 - 043 Counter/Timer Registers

044 - 05F Unused

060 Keyboard Data

061 Port B

062 - 063 Unused

064 Keyboard Command/Status

065 - 06F Unused

070 CMOS Index Address

071 CMOS Data

072 - 073 Unused

074 Reserved

075 Unused

076 Reserved

077 - 077F Unused

080 - 08F DMA Page Registers

084 - 085 POST Code Output Port

090 - 091 Unused

092 Fast Reset Register

093 - 09F Unused

---------------------------------------------------------------------------


---------------------------------------------------------------------------

0A0 - 0A1 Interrupt Controller # 2

0A2 - 0BF Unused

0C0 - 0DF DMA Controller # 2

0E0 - 0E1 Unused

0E2 - 0E3 MSIO Configuration Registers

0E4 - 0EF Unused

0F0 - 0F1 NCP Numerics Register

0F9 Unused

0FA Unused

0FB Unused

0FC - 0FF Unused

100 - 101 Unused

103 - 16F Unused

170 - 177 Hard Drive Secondary Registers

178 - 1EF Unused

1F0 - 1F7 Hard Drive Primary Registers

1F8 - 1FF Unused

200 - 21F Unused

220 - 22F Unused

230 - 23F Unused

240 - 24F Unused

250 - 25F Unused

260 - 277 Unused

278 - 27A LPT2 and High Speed Parallel Port Registers

27B - 27F LPT2 High Speed Printer Port Registers

---------------------------------------------------------------------------


---------------------------------------------------------------------------

280 - 2F7 Unused

2F8 - 2FF Serial Control Register COM2

300 - 36F Unused

370 - 371 Reserved

372 Diskette Digital Output Register

373 Unused

374 Reserved

375 Diskette Main Status/Data Registers

376 Reserved

377 Diskette Input/Control Registers

378 - 37A LPT1 and High Speed Parallel Port Registers

37B - 37F Unused

380 - 387 Unused

388 - 38B Unused

38C - 3AF Unused

3B0 - 3BB Cirrus Logic Video Controller

3BC - 3BE LPT3 and High Speed Parallel Port Registers

3BF LPT1 High Speed Parallel Port Registers

3C0 - 3CD Cirrus Logic Video Controller

3D0 - 3DF Cirrus Logic Video Controller

3F0 - 3F7 Diskette Drive Controller Primary Registers

3F8 - 3FF COM1 Serial Controller Registers

400 - 4CF Unused

480 - 48F Extended DMS Registers

4D0 - CF6 Unused

CF7 Configuration/NVM Data Register

CF8 - CFB PCI Configuration Index Register

CFC - CFF PCI Configuration Data Register

D00 - FFF Unused

===========================================================================

System Memory Map

Table 7-12

===========================================================================

Size Memory Address System Function

===========================================================================

640 K 00000000 - 0009FFFF Base Memory

128 K 000A0000 - 000BFFFF Video Memory

48 K 000C0000 - 000CBFFF Video BIOS

160 K 000C8000 - 000E7FFF Unused

64 K 000E8000 - 000FFFFF System BIOS

15 M 00100000 - 00FFFFFF Extended Memory

58 M 01000000 - 047FFFFF Super Extended Memory

58 M 04800000 - 07FFFFFF Unused

2 M 08000000 - 080FFFFF Video Memory (Direct Access)

4 G 08200000 - FFFEFFFF Unused

64 K FFFF0000 - FFFFFFFF System BIOS ("SHADOW")

===========================================================================

Appendix A - Connector Pin Assignments

This appendix contains the pin assignments for all external connectors.

Table A-1. Parallel Connector

===========================================================================

Pin Signal

===========================================================================

1 Strobe *

2 Data Bit 0

3 Data Bit 1

4 Data Bit 2

5 Data Bit 3

6 Data Bit 4

7 Data Bit 5

8 Data Bit 6

9 Data Bit 7

10 Acknowledge *

11 Busy

12 Paper Out

13 Select

14 Auto Linefeed *

15 Error *

16 Initialize Printer *

17 Select In *

18 Ground

19 Ground

20 Ground

21 Ground

22 Ground

23 Ground

24 Ground

25 Ground

---------------------------------------------------------------------------

* = Active low

===========================================================================

Table A-2. Serial Connector

===========================================================================

Pin Signal

===========================================================================

1 Carrier Detect

2 Receive Data

3 Transmit Data

4 Data Terminal Ready

5 Ground

6 Data Set Ready

7 Ready to Send

8 Clear to Send

9 Ring Indicator

===========================================================================

Table A-3. Keyboard/Mouse Connector

===========================================================================

Pin Signal

===========================================================================

1 Data

2 Reserved

3 Ground

4 +5V

5 Clock

6 Reserved

===========================================================================

Table A-4. External VGA Monitor Connector

===========================================================================

Pin Signal

===========================================================================

1 Red Analog

2 Green Analog

3 Blue Analog

4 Not Connected

5 Ground

6 Ground Analog

7 Ground Analog

8 Ground Analog

9 Not Connected

10 Ground

11 Not Connected

12 Not Connected

13 Horizontal Synch

14 Vertical Synch

15 Not Connected

===========================================================================

Table A-5. PC Card (PCMCIA) Connector

===========================================================================

Pin Signal

===========================================================================

1 Ground

2 Data bit 3

3 Data bit 4

4 Data bit 5

5 Data bit 6

6 Data bit 7

7 Card enable 1

8 Address bit 10

9 Output enable

10 Address bit 11

11 Address bit 9

12 Address bit 8

13 Address bit 13

14 Address bit 14

15 Program/Write enable

16 Ready or busy/Interrupt request

17 Power

18 Programming and Peripheral supply 1

19 Address bit 16

20 Address bit 15

21 Address bit 12

22 Address bit 7

23 Address bit 6

24 Address bit 5

25 Address bit 4

---------------------------------------------------------------------------

Pin Signal

---------------------------------------------------------------------------

26 Address bit 3

27 Address bit 2

28 Address bit 1

29 Address bit 0

30 Data bit 0

31 Data bit 1

32 Data bit 2

33 Write protect/IO Port is 16-bit

34 Ground

35 Ground

36 Card detect 1

37 Data bit 11

38 Data bit 12

39 Data bit 13

40 Data bit 14

41 Data bit 15

42 Card enable 2

43 Refresh

44 IO Read

45 IO Write

46 Address bit 17

47 Address bit 18

48 Address bit 19

---------------------------------------------------------------------------

Pin Signal

---------------------------------------------------------------------------

49 Address bit 20

50 Address bit 21

51 Power

52 Programming and peripheral supply 2

53 Address bit 22

54 Address bit 23

55 Address bit 24

56 Address bit 25

57 Reserved

58 Card reset

59 Extend bus cycle

60 Input port acknowledge

61 Register select and IO enable

62 Battery voltage detect 2/Audio digital waveform

63 Battery voltage detect 1/Card status changed

64 Data bit 8

65 Data bit 9

66 Data bit 10

67 Card detect 2

68 Ground

===========================================================================

Appendix B - Power Cord Set Requirements

2-Conductor Power Cord Set

The wide-range input feature of your computer permits it to operate from any line voltage between 100 to 240 volts AC.

The power plug or power cord set (appliance coupler, flexible cord, and wall plug) you received with your computer meets the requirements for use in the country where you purchased your computer.

Power cord sets for use in other countries must meet the requirements of the country where you use the computer. For more information on power cord set requirements, contact your Compaq authorized dealer.

General Requirements

The requirements listed below are applicable to all countries:

1. The length of the power cord set must be at least 6.00 feet (1.8 m) and

a maximum of 9.75 feet (3.0 m). The measurements only apply to the

power cord set. The length of a surge suppresser, if one is used, is

not taken into account in these length requirements.

2. All power cord sets must be approved by an acceptable accredited agency

responsible for evaluation in the country where the power cord set will

be used.

3. The power cord set must have a minimum current capacity of 2.5A and a

nominal voltage rating of 125 or 250 volts AC, as required by each

country's power system.

4. The appliance coupler must meet the mechanical configuration of an EN

60 320/IEC 320 Standard Sheet C7 connector, for mating with appliance

inlet on the AC Adapter.

Country-Specific Requirements

===========================================================================

-- 2-Conductor Power Cord Set Requirements - By Country --

Accredited Applicable

Country Agency Note Numbers

===========================================================================

Australia EANSW 1

Austria OVE 1

Belgium CEBC 1

Canada CSA 2

Denmark DEMKO 1

Finland FIMKO 1

France UTE 1

Germany VDE 1

Italy IMQ 1

Japan JIS 3

The Netherlands KEMA 1

Norway NEMKO 1

Sweden SEMKO 1

Switzerland SEV 1

United Kingdom BSI 1

United States UL 2

---------------------------------------------------------------------------

NOTES: 1. Flexible cord must be Type HO3VV-F, 2-conductor, 0.75 mm2

conductor size. Power cord set fittings (appliance coupler and

wall plug) must bear the certification mark of the agency

responsible for evaluation in the country where it will be used.

2. Flexible cord must be Type SPT-2 or equivalent, No. 18 AWG,

2-conductor. Wall plug must be a two-pole type with a NEMA 1-15P

(15A, 125V) configuration.

===========================================================================

No results