Sharp GX18 User guide

Declaration of Conformity

Hereby, Sharp Telecommunications of Europe Limited, declares that this GX18 is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC.

A copy of the original declaration of conformity can be found at the following Internet address: http://www.sharp-mobile.com

Sharp Telecommunications of Europe Ltd.

Azure House, Bagshot Road, Bracknell, Berkshire RG12 7QY UK

http://www.sharp-mobile.com

Introduction

Congratulations and thank you for choosing the GX18.

About This User Guide

This User Guide is carefully designed to help you learn about your phone’s features and operations quickly and effectively.

NOTICE

• We strongly recommend that you keep separate permanent written records of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, we assume no responsibility for data lost or otherwise rendered unusable, whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired or any other cause.

• We assume no responsibility, directly or indirectly, for financial losses or claims from third parties resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss or alteration of stored data, etc.

• All company and/or product names are trademarks and/or registered trademarks of their respective holders.

• Screen layout illustrated in this User Guide may differ from the actual one.

The information described in this User Guide is subject to change without notice.

• All the functions described in this User Guide may not be supported in all networks.

• We assume no responsibility for downloaded contents, information, etc. from the network.

• Occasionally, a few black or bright pixels may appear on the screen. Please note that this will not have any impact on any of the features or performance.

Intellectual Property Rights

According to copyright laws, the reproduction, alteration and use of material which is protected by copyright (music, pictures, etc.) is only permitted for personal or private use. If the user is not in possession of more extensive copyright or has not received the explicit permission from the copyright owner to reproduce, alter or use a copy which has been made or modified in this way, this is considered to be a violation of the copyright laws and gives the copyright owner the right to claim for damages. For this reason, avoid the illegal use of material which is protected by copyright.

Windows is a registered trademark of Microsoft

Corporation in the United States and/or other countries.

Introduction 1

Powered by JBlend™ Copyright 1997-2008

Aplix Corporation. All rights reserved. JBlend and all JBlend-based trademarks and logos are trademarks or registered trademarks of Aplix

Corporation in Japan and other countries.

Licensed by Inter Digital Technology Corporation under one or more of the following United States Patents and/or their domestic or foreign counterparts and other patents pending, including U.S. Patents: 4,675,863: 4,779,262:

4,785,450 & 4,811,420.

T9 Text Input is licensed under one or more of the following:

U.S. Pat. Nos. 5,818,437, 5,953,541, 5,187,480, 5,945,928, and 6,011,554; Australian Pat. No. 727539; Canadian Pat.

No. 1,331,057; United Kingdom Pat. No. 2238414B; Hong

Kong Standard Pat. No. HK0940329;Republic of Singapore

Pat. No. 51383; Euro. Pat. No. 0 842 463 (96927260.8) DE/

DK, FI, FR, IT, NL,PT.ES,SE,GB; Republic of Korea Pat.

Nos. KR201211B1 and KR226206B1; and additional patents are pending worldwide.

Bluetooth is a trademark of the Bluetooth SIG, Inc.

This product is licensed under the MPEG-4 Visual

Patent Portfolio License for the personal and noncommercial use of a consumer to (i) encode video in compliance with the MPEG-4 Video Standard

(“MPEG-4 Video”) and/or (ii) decode MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a licensed video provider. No license is granted or implied for any other use. Additional information may be obtained from MPEG LA. See http:// www.mpegla.com.

This product is licensed under the MPEG-4 Systems Patent

Portfolio License for encoding in compliance with the MPEG-

4 Systems Standard, except that an additional license and payment of royalties are necessary for encoding in connection with (i) data stored or replicated in physical media which is paid for on a title by title basis and/or (ii) data which is paid for on a title by title basis and is transmitted to an end user for permanent storage and/or use. Such additional license may be obtained from MPEG LA, LLC. See http:// www.mpegla.com for additional details.

The Bluetooth word mark and logos are owned by the

Bluetooth SIG, Inc. and any use of such marks by Sharp is under license. Other trademarks and trade names are those of their respective owners.

CP8 PATENT

2 Introduction

Useful Functions and Services

Your phone offers you the following features:

• A built-in digital camera for taking pictures and video clips.

• A message function for reading and creating SMS messages.

• MMS (Multimedia Messaging Services) for personalising your phone in various ways.

• A WAP browser for accessing information on the mobile internet.

• Java™ applications. You can also download various applications from Vodafone via the mobile internet.

• Email for sending up to 2000 characters and receiving mail with attachments.

• A voice recorder function for recording and playing back voice clips.

• A Bluetooth ® wireless technology interface for establishing contact and transmitting data with certain devices. You can transmit pictures, sounds, and video clips to OBEX-enabled phones.

• A data synchronization function for synchronizing the Contacts List and schedule entries with Microsoft

Outlook or Outlook Express on a PC.

• A schedule alarm for creating and sending schedule entries with alarm settings.

Introduction 3

SAFETY PRECAUTIONS

Your phone conforms to international regulations in so far as it is used under normal conditions and in accordance with the following instructions.

Sharp and Vodafone disclaim any liability for damage which may result as a consequence of improper use or use contrary to the instructions contained herein.

Read the safety information sections of this user

guide on pages 4 to 13.

Do not use hand-held while driving.

For body-worn operation, maintain a separation of

1.5 cm.

Small parts may cause a choking hazard.

This device may produce a loud sound.

Keep away from pacemakers and other personal medical devices.

Switch off when instructed in hospitals and medical facilities.

Switch off when instructed in aircrafts and airports.

4 SAFETY PRECAUTIONS

Switch off in explosive environments.

Do not use while re-fuelling.

This device may produce a bright or flashing light.

(* The flashing light feature is not available on all products.)

Do not dispose of in a fire.

Avoid contact with magnetic media.

Avoid extreme temperatures.

Avoid contact with liquid, keep dry.

Do not attempt to disassemble.

Do not rely on this device for emergency communications.

Only use approved accessories.

RADIOFREQUENCY (RF) EXPOSURE

General Statement on RF Energy

Your phone contains a transmitter and a receiver. When it is ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits.

Specific Absorption Rate (SAR)

Your mobile device is a radio transmitter and receiver.

It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines.

These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health.

The guidelines use a unit of measurement known as the

Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 2 W/kg and the highest SAR value for this device when tested at the ear was “0.977“ W/kg*.

As mobile devices offer a range of functions, they can be used in other positions, such as on the body as described in this user guide**. In this case, the highest tested SAR value is “1.63“ W/kg.

As SAR is measured utilising the device’s highest transmitting power, the actual SAR of this device while operating is typically below that indicated above. This is due to automatic changes to the power level of the device to ensure it only uses the minimum level required to communicate with the network.

* The tests are carried out in accordance with international guidelines for testing.

** Please see the section below about body worn operation.

Body Worn Operation

Important safety information regarding radiofrequency radiation (RF) exposure:

• To ensure compliance with RF exposure guidelines the phone must be used with a minimum of 1.5 cm separation from the body.

• Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits.

SAFETY PRECAUTIONS 5

Limiting Exposure to Radiofrequency (RF)

Fields

For individuals concerned about limiting their exposure to RF fields, the World Health Organisation (WHO) provides the following advice:

• Precautionary measures: Present scientific information does not indicate the need for any special precautions for use of mobile phones. If individuals are concerned, they might choose to limit their own or their children’s RF exposure by limiting the length of calls, or using ‘hands-free’ devices to keep mobile phones away from the head and body.

• For further information readers are referred to: http://www.who.int/

INFORMATION ON PROPER

DISPOSAL

Attention: Your product is marked with this symbol.

It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.

A. Information on Disposal for Users (private households)

1. In the European Union

Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!

Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.

Following the implementation by member states, private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one.

*) Please contact your local authority for further details.


If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according to local requirements.

By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.

B. Information on Disposal for Business Users

1. In the European Union

If the product is used for business purposes and you want to discard it:

Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities.

For Spain: Please contact the established collection system or your local authority for takeback of your used products.

2. In other Countries outside the EU

If you wish to dispose of this product, please contact your local authorities and ask for the correct method of disposal.

DISTRACTIONS

Driving

Full attention must be given to driving at all times in order to reduce the risk of an accident. Using a phone while driving (even with a handsfree kit) causes distraction and can lead to an accident. You must comply with local laws and regulations restricting the use of wireless devices while driving.

Operating Machinery

Full attention must be given to operating the machinery in order to reduce the risk of an accident.


PRODUCT HANDLING

General Statement on Handling and Use

You alone are responsible for how you use your phone and any consequences of its use.

• You must always switch off your phone wherever the use of a phone is prohibited. Use of your phone is subject to safety measures designed to protect users and their environment.

• Always treat your phone and its accessories with care and keep it in a clean and dust-free place.

• Do not expose your phone or its accessories to open flames or lit tobacco products.

• Do not expose your phone or its accessories to liquid, moisture or high humidity.

• Do not drop, throw or try to bend your phone or its accessories.

• Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.

• Do not paint your phone or its accessories.

• Do not attempt to disassemble your phone or its accessories. Only authorised personnel must do so.

• Please check local regulations for disposal of electronic products.

• Do not carry your phone in your back pocket as it could break when you sit down.

Small Children

Do not leave your phone and its accessories within the reach of small children or allow them to play with it.

They could hurt themselves or others, or could accidentally damage the phone.

Your phone contains small parts with sharp edges that may cause an injury or which could become detached and create a choking hazard.

Demagnetisation

To avoid the risk of demagnetisation, do not allow electronic devices or magnetic media close to your phone for a long time.

Electrostatic Discharge (ESD)

Do not touch the SIM card’s metal connectors.

Antenna Care

Do not cover the top of the phone with your hand when in use as this may interfere with the performance of the built-in aerial. Call quality may deteriorate leading to shortened talk-time and standby time because the mobile phone has to operate on a higher power level than in necessary.


Normal Use Position

When placing or receiving a phone call, hold your phone to your ear, with the bottom towards your mouth or as you would a fixed line phone.

Air Bags

• Do not place a phone in the area over an air bag or in the air bag deployment area.

• Store the phone safely before driving your vehicle.

Seizures/Blackouts

If your phone is capable of producing bright flashing lights, please be careful because it may trigger seizures or blackouts.

Repetitive Motion Injuries

To minimise the risk of RSI (Repetitive strain injury), when texting or playing games with your phone:

• Do not grip the phone too tightly.

• Press the buttons lightly.

• Make use of the special features in the handset which minimise the number of buttons which have to be pressed, such as message templates and predictive text.

• Take lots of breaks to stretch and relax.

Emergency Calls

This phone, like any wireless phone, operates using radio signals, which cannot guarantee connection in all conditions. Therefore, you must never rely solely on any wireless phone for emergency communications.

Loud Noise

This phone is capable of producing loud noises which may damage your hearing.

Bright Light

If your phone is capable of producing a bright light, do not use it too close to the eyes.

Phone Heating

Your phone may become warm during charging and during normal use.


ELECTRICAL SAFETY

Accessories

• Use your phone only with batteries, chargers and accessories recommended by the manufacturer. The manufacturer disclaims any liability for damage caused by the use of other chargers, batteries or accessories.

• Before connecting the phone with a PC or a peripheral unit, read the operation manual for the other unit carefully.

• Do not touch the battery terminals. Batteries can cause damage, injury or burns if a conductive material touches exposed terminals. When the battery is detached from the phone, use a cover made of non-conductive material for keeping and carrying the battery safely.

Connection to a Car

Seek professional advice when connecting a phone interface to the vehicle electrical system.

Faulty and Damaged Products

• Do not attempt to disassemble the phone or its accessory.

• Only qualified personnel must service or repair the phone or its accessory.

• If your phone or its accessory has been submerged in water, punctured, or subjected to a severe fall, do not use it until you have taken it to be checked at an authorised service centre.

INTERFERENCE

General Statement on Interference

Care must be taken when using the phone in close proximity to personal medical devices, such as pacemakers and hearing aids.


Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 15 cm be maintained between a mobile phone and a pacemaker to avoid potential interference with the pacemaker. To achieve this, use the phone on the opposite ear to your pacemaker and do not carry it in a breast pocket.

Hearing Aids

• People with hearing aids or other cochlear implants may experience interfering noises when using wireless devices or when one is nearby.

• Since the level of interference will depend on the type of hearing device and the distance from the interference source, increasing the separation between them may reduce the interference. You may also consult your hearing aid manufacturer to discuss alternatives.

Medical Devices

Please consult your doctor and the device manufacturer to determine if operation of your phone may interfere with the operation of your medical device.

Hospitals

Switch off your wireless device when requested to do so in hospitals, clinics or health care facilities. These requests are designed to prevent possible interference with sensitive medical equipment.

Aircraft

Switch off your wireless device whenever you are instructed to do so by airport or airline staff.

Interference in Cars

Please note that because of possible interference to electronic equipment, some vehicle manufacturers forbid the use of mobile phones in their vehicles unless a handsfree kit with an external antenna is included in the installation.


EXPLOSIVE ENVIRONMENTS

Petrol Stations and Explosive Atmospheres

• In locations with potentially explosive atmospheres, obey all posted signs to turn off wireless devices such as your phone or other radio equipment.

• Areas with potentially explosive atmospheres include fuelling areas, below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust, or metal powders.

Blasting Caps and Areas

To avoid interfering with blasting operations, turn off your mobile phone or wireless device when in a blasting area or in areas posted “turn off two-way radios or electronic devices”.


CONDITIONS OF USE

Battery

• Network configuration and phone usage will affect talk-time and standby time.

Using the games or camera will hasten battery consumption.

• When the battery charging alert is displayed on

the screen, charge the battery as soon as possible.

If you continue using your phone ignoring the alert, the phone may cease to function, and all data and settings you have stored may be lost.

• Before removing the battery from the phone, make sure the phone is switched off.

• Replace and charge the new battery as soon as possible after removing the old one.

• Recommended temperature for using and storing batteries is approximately 20°C.

• The batteries’ performance is limited in low temperatures, particularly below 0°C and the phone may not work temporarily regardless of the amount of remaining battery power.

• The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED

BY AN INCORRECT TYPE,

DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS

See “Battery Disposal” on page 23.

Camera Operation

• Learn picture quality, file formats, etc. beforehand.

The taken pictures can be saved in JPEG format.

• Be careful not to move your hand while taking pictures.

If the phone moves while taking a picture, the picture can become blurred. When taking a picture, hold the phone firmly to prevent it from moving, or use the delay timer.

• Clean the lens cover before taking a picture.

Fingerprints, oils, etc. on the lens cover hinder clear focusing. Wipe them off with a soft cloth before taking a picture.

Others

• As with any electronic storage unit, data may be lost or corrupted under various circumstances.

• If the phone’s battery has been removed for some time, or the phone has been reset, the unit’s clock and calendar may be reinitialised. The date and time should be updated in this case.

• Use only specified handsfree kits (supplied or optional). Some phone’s functions may not work when unauthorised handsfree kit is used.

CONDITIONS OF USE 13

Table of Contents

14

Introduction ................................................. 1

Useful Functions and Services .................... 3

SAFETY PRECAUTIONS ............................. 4

RADIOFREQUENCY (RF) EXPOSURE .. 5

INFORMATION ON PROPER DISPOSAL

6

DISTRACTIONS ........................................ 7

PRODUCT HANDLING ............................ 8

ELECTRICAL SAFETY .......................... 10

INTERFERENCE ..................................... 10

EXPLOSIVE ENVIRONMENTS ............. 12

CONDITIONS OF USE ............................... 13

List of Menu Functions ............................. 17

Your Phone ................................................ 19

Accessories ................................................ 19

Getting Started .......................................... 20

Inserting the SIM Card and the Battery .... 22

Charging the Battery ................................. 24

Turning Your Phone On and Off ............... 25

Keypad Lock ............................................. 26

Display Indicators ..................................... 26

Table of Contents

Navigating Functions ................................28

Call Functions ............................................29

Making a Call ............................................ 29

Speed Dialing ............................................ 29

Redialing .................................................... 30

Answering a Call ....................................... 30

In Call Menu .............................................. 31

Entering Characters ..................................35

Changing the Input Languages .................. 35

Changing the Input Method ....................... 35

Using Text Templates ................................ 36

Using the Menu ..........................................37

Contacts .....................................................38

Contacts List .............................................. 38

Add New Contact ...................................... 39

Memory Status ........................................... 41

Speed Dial List .......................................... 41

Sending a Contacts List Entry ................... 42

Call Log ..................................................... 42

Speed Dial List .......................................... 43

Advanced ................................................... 43

My Numbers .............................................. 43

Data Counter .............................................. 44

Call Charges ............................................... 44

Camera ....................................................... 46

Take Picture ............................................... 46

Record Video ............................................. 50

Messages ................................................... 53

Multimedia (MMS) .................................... 53

Text (SMS) ................................................ 57

Email .......................................................... 60

Cell Broadcasts .......................................... 62

Vodafone live! ............................................ 63

Starting the WAP Browser ........................ 63

Navigating a WAP Page ............................ 63

My Items ..................................................... 65

Pictures ...................................................... 65

Videos ........................................................ 67

Games & More ........................................... 68

Sounds ........................................................ 70

Bookmarks ................................................. 71

Memory Status ........................................... 72

Games & More ........................................... 73

More Games ............................................... 73

Applications ...............................................73

Settings .......................................................74

Java™ Information .....................................75

Applications ............................................... 76

SIM Application .........................................76

Alarms ........................................................76

Calculator ...................................................77

Voice Recorder ..........................................78

Phone Help .................................................78

Calendar ..................................................... 79

Settings ...................................................... 82

Setting the Display .....................................82

Sound .........................................................84

Profiles .......................................................84

Connectivity ...............................................88

Date & Time ...............................................90

Call Settings ...............................................91

Changing the Language .............................95

Network ......................................................95

Security ......................................................99

Master Reset .............................................100

Connecting GX18 to Your PC ................. 101

System Requirements ...............................101

Table of Contents 15

CAMagic Mobile ..................................... 101

Troubleshooting ...................................... 102

Index ......................................................... 105

16 Table of Contents

List of Menu Functions

GX18 functions are listed below.

See relevant page for details of each function. The menu’s corresponding number is used for shortcuts. For details, see page 37.

1 Games & More

2 Vodafone live!

3 Applications

4 Messages

1 More Games

2 Applications

3 Settings

4 Java™ Information

1 Vodafone live!

2 Games

3 Ringtones

4 Pictures

5 News

6 Sport

7 Find & Seek

8 Chat

9 Search

1 SIM Application *

2 Alarms

3 Calculator

4 Voice Recorder

5 Phone Help

1 Create Message

2 Multimedia

3 Text Message

4 Email

5 Media Album

6 Vodafone Mail

7 Messenger

8 Cell Broadcasts

9 Area Info

-

-

-

-

-

-

-

(p. 73)

(p. 73)

(p. 74)

(p. 75)

(p. 63)

(p. 76)

(p. 76)

(p. 77)

(p. 78)

(p. 78)

(p. 53, 57, 60)

(p. 53)

(p. 57)

-

-

(p. 60)

-

(p. 62)

-

5 Camera

6 My Items

1 Take Picture

2 Record Video

1 Pictures

2 Videos

3 Games & More

4 Sounds

5 Bookmarks

6 Memory Status

7 Calendar

1 Contacts List

2 Add New Contact

3 Call Log

4 Speed Dial List

8 Contacts

5 Advanced

6 My Numbers

7 Data Counter

8 Call Charges *

9 Settings

1 Display

2 Sound

3 Profiles

4 Connectivity

5 Date & Time

6 Call Settings

7 Languages

8 Network

9 Security

10 Master Reset

* Depends on SIM card contents.

(p. 43)-

(p. 43)

(p. 44)

(p. 44)

(p. 82)

(p. 84)

(p. 84)

(p. 88)

(p. 90)

(p. 91)

(p. 95)

(p. 95)

(p. 99)

(p. 100)

(p. 46)

(p. 50)

(p. 65)

(p. 67)

(p. 68)

(p. 70)

(p. 71)

(p. 72)

(p. 79)

(p. 38)

(p. 39)

(p. 42)

(p. 41)

List of Menu Functions 17

Note for the menu references for the Postcard and

Media Album services

• The menu references for the Postcard and Media

Album services vary in the United Kingdom and

Ireland as follows:

Current references in the User Guide

“Postcard”

“As Postcard”

“State/Province”

“Media Album”

“To Album”

References in

United Kingdom

“live! Postcard”

“As live! Postcard”

“County”

“live! Studio”

“To live! Studio”

References in

Ireland

(Not available)

(Not available)

“State/Province”

“Picture Album”

“To Picture Album”

18 List of Menu Functions

Your Phone

Please check the following carefully. Your phone should come complete with:

• GSM 900/1800 GPRS phone

• Rechargeable Li-ion Battery

• AC Charger

• CD-ROM

• User Guide

• Quick Start Guide

Accessories

• Li-ion Spare Battery (XN-1BT18)

• AC Charger (XN-1QC18, XN-1QC19)

• Personal Hands-free Kit (XN-1ER18)

The above accessories may not be available in all regions.

For details, please contact your dealer.

Your Phone 19

Getting Started

1 13

14

8

2

3

4

5

6

7

9

10

11

12

15

1. Earpiece

2. Navigation Keys (Arrow Keys):

Moves cursor to select menu items, etc.

Up/Down arrow keys: Displays Contacts List

/ entries in standby mode.

Left arrow key:

and indicate in this manual these keys.

Displays list of Applications

Right arrow key:

3. Centre Key:

16

indicates in this manual this key.

Displays list of Saved

Pictures in standby mode.

indicates in this manual this key.

Displays Main menu in standby mode and executes functions.

20 Getting Started

4. Left Soft Key:

5. Send Key:

6. Voice Mail Key:

7. * /Shift Key:

8. Display

9. Right Soft Key:

10.End/Power Key:

11.Keypad

Executes the function at the bottom left of the screen.

Makes or accepts calls, views the call log in standby mode.

Press and hold this key to connect to the Voice mail centre automatically.

(Depends on the SIM card.)

Switches character case among four modes: Abc,

ABC, 123 and abc.

Executes the function at the bottom right of the screen.

Used to access “Vodafone live!” by opening the browser in standby mode.

Ends a call, turns power on/ off.

12.# Key: Switches symbol screens.

Press and hold this key on the text entry screen to shift text input method between multi-tap and T9 mode.

Press and hold this key during standby to switch

Profiles settings between

Normal and Silent mode.

Press , then during standby to activate Voice

Recorder.

13.External Connector:

Used to connect either the charger, headset, or USB data cable.

14.Side-Up/Side-Down Keys:

Moves cursor to select menu items, adjusts earpiece volume, etc.

15.Microphone

16.Camera

Getting Started 21

Inserting the SIM Card and the

Battery

1.

Remove the battery cover as shown below.

1

2

2.

Slide the SIM card into the SIM holder.

3.

Hold the battery so that the metal contacts of the battery are facing down, slide the guides on the top of the battery into the battery slots, and then insert it

4.

Replace the battery cover

SIM card


Note

• Always use with the battery cover closed.

• Make sure that only 3V SIM cards are used.

• Make sure that the standard accessory battery

(XN-1BT18) is used.

Removing the SIM Card and the Battery

1.

Make sure you turn off your phone and disconnect the charger and other accessories. Remove the battery cover.

1

3.

Hold down gently while sliding the SIM card out of the SIM holder.

2

2.

Pick up the battery using the protruding edge and remove the battery from the phone.

Battery Disposal

In order to protect the environment, please read the following points concerning battery disposal:

• Take the used battery to your local waste depot, dealer or customer service centre for recycling.

• Do not expose the used battery to an open flame, into water or dispose with the household waste.


Charging the Battery

You must charge the battery for at least 2 hours before using your phone for the first time.

Using the Charger

1.

Open the cover of the external connector, and connect the charger horizontally.

2.

Connect the charger to a power outlet.

Note

• Charging time may vary depending on the state of the

battery and other conditions. (See “Battery” on page 13.)

To Disconnect the Charger

When charging is complete, the battery indicator icon displays the full charge status.

1.

Disconnect the charger from the power outlet.

2.

Disconnect the charger from the external socket of the phone.

When the phone is charging, the animated battery status icon ( ) in the upper right of the screen displays the current status.

Standard charging time: Approx. 2 hours.

Note

• Do not use any non approved charger, this may damage your phone and invalidate any warranty,

please see “Battery” on page 13 for details.

• Forcibly disconnecting the charger may cause malfunction.


To Charge Using the Cigarette Lighter Charger

The optional Cigarette Lighter Charger supplies power for charging from the cigarette lighter socket of a car.

Battery Level Indicator

The current battery level is displayed in the upper right hand side of the screen.

Low Battery During Use

When the battery is running low, an alarm will sound and the “ ” is displayed on the screen.

If you are using your phone and you hear the “low battery” alarm, attach your charger as soon as possible.

The phone may not be able to continue normal operation if you continue to use it. The battery may only last approximately five minutes before the phone itself powers down during use.

Battery Indicators Charge Level

Sufficiently charged

Partially charged

Charging recommended

Charging required

Empty

Turning Your Phone On and Off

To turn the power on, press and hold approximately 6 seconds.

for

The standby screen is displayed.

To turn the power off, press and hold approximately 6 seconds.

for

To Enter the PIN Code

If activated you are asked to enter a PIN (Personal

Identification Number) code after turning on your phone.

1.

Enter your PIN code.

2.

Press .

Note

• If your PIN code is entered incorrectly three times in

a row, the SIM card is locked. See “Enabling/

Disabling the PIN Code” on page 99.


Keypad Lock

You can lock the keypad to prevent it from being pressed accidentally.

Locking the Keypad

1.

Press , then [LockKeys] during standby.

The soft and centre keys are not displayed when locked.

To unlock, press , then [Yes].

Tip

• Emergency numbers (112, etc.) can be input and dialed regardless of the keypad lock.

• To lock the keypad automatically, see “Auto Keypad

Lock” on page 99.

Display Indicators

Left soft key

Centre key

Status indicators

Right soft key


Status Indicators

1.

/ : Strength of received signal / Service out of range

2.

:

3.

/ :

GPRS enabled and within range — flashes during GPRS transmission.

Text message alerts [unread / mailbox full]

4.

5.

6.

/

:

/ :

: Multimedia message alerts [unread / mailbox full]

Email alerts [unread / mailbox full]

WAP alert

7.

/ : Java™ application [executed (colour) / suspended (grey)]

8. (No display)/ / / / :

Current profile [Normal / Meeting /

Activity / Headset / Silent]

9.

10.

:

:

“All Calls” diverts set to “On” (p. 91)

Call incoming

11.

:

12.

/ :

Call in progress

Current WAP or MMS communication mode [CSD / GPRS]

13.

:

14.

:

15.

:

16.

:

17.

:

18.

/ :

19.

20.

:

21.

:

:

22.

:

23.

:

24.

/ :

25.

:

Battery level

Roaming outside network

Ringer Volume (p. 84) set to “Silent”

Vibration alert (p. 85) enabled

USB Data Cable connected

Bluetooth wireless setting [enabled / communicating]

Data communication mode enabled

Fax communication mode enabled

Outbox contains unsent multimedia messages

Voicemail message alert

Daily alarm enabled

Schedule entry enabled [with / without reminder alarm]

Keypad Lock (p. 26, p. 99) enabled


28

Navigating Functions

All applications are accessed from the Main menu. To open the Main menu, press the centre key ( ) during standby.

To launch applications, you will need to highlight menu items, and make selections. To select a menu item

(indicated in quotation marks), move the cursor using selection.

In certain procedures, you will need to press one of the soft keys (indicated in square brackets), which are displayed at the bottom left and right of the screen.

Press the corresponding soft key ( or ).

To return to the previous screen, press the right soft key if it displays “Back”. To close the Main menu, press the right soft key if it displays “Exit”.

Each section in this User Guide starts with a list of items you will need to select in order (indicated in

italics) before performing the procedures shown. Select each item to reveal the next set of items that you have to select. Open subsection items after opening those listed in the main section.

Example:

“Camera”

→

“Record Video”

→

[Options]

→

“Video Quality”

Navigating Functions

Call Functions

Making a Call

1.

Enter the area code and the phone number you wish to dial and press to dial.

If you enter the wrong number, press [Clear] to delete the number to the left of the cursor.

Emergency Calls

1.

Enter 112 (international emergency number) using the keypad and press to dial.

Note

• Emergency calls may not be available on all mobile phone networks when certain network services and/ or phone features are in use. Contact your network operator for more information.

• This Emergency number can normally be used to make an emergency call in any country, with or without a SIM card inserted, if a GSM network is within range.

International Calls

1.

Press and hold

+

until a “+” (international dialing prefix) sign is displayed.

2.

Enter the country code, followed by the area code

(without the leading zero) and the phone number, and press to dial.

Speed Dialing

Up to 8 phone numbers from the Contacts List memory

(Handset and SIM) can be assigned to speed dials. You can call the numbers using the digit keys (

ABC

to ).

For details on setting the Speed Dial List, see “Speed

Dial List” on page 41.

1.

To dial a number using the speed dial function, press and hold any of the digit keys (

ABC

to ).

The phone number stored in the Speed Dial List is dialed.

Call Functions 29

Redialing

1.

Press during standby.

2.

Select the phone number you wish to call.

3.

Press to redial the call.

Automatic Redialing

This setting allows you to automatically redial the number if the first attempt was unsuccessful because the called party was busy.

If you wish to stop redialing, press or [End].

To Set the Auto Redial Function

“Settings”

→

“Call Settings”

→

“Auto Redial”

1.

Select “On” or “Off”.

Note

• When you receive an incoming call, the Auto Redial function is interrupted.

• Automatic redialing is not available for fax and data calls.

Answering a Call

When an incoming call is detected, the phone rings.

1.

Press , or [Answer] to answer the call.

Tip

• When the Personal Hands-free Kit (option) is connected to the phone, you can answer calls by pressing the Answer button.

• If you have subscribed to the Calling Line

Identification (CLI) service and the caller’s network sends the number, the caller’s number is displayed on the screen. If the caller’s name and number are stored in the Contacts List, the caller’s name and phone number are displayed on the screen.

• If the number is a restricted number, the display shows “Withheld”.

• When receiving a call from the person whose picture is registered in the Contacts List, receiving display and the picture are displayed alternately.

30 Call Functions

Using the Loud Speaker

1.

During a call, press [Options].

2.

Select “Loud speaker on”.The loud speaker is activated.

3.

Select “Loud speaker off“. The loud speaker is deactivated.

Rejecting an Incoming Call

1.

Press or press and hold the side-up or sidedown key while the phone is ringing to reject a call you do not wish to answer.

Letting the Caller Know You are Unavailable

1.

Press [Busy] while the phone is ringing to send a busy tone to the caller of an incoming call letting them know that you cannot answer the call.

In Call Menu

Your phone has additional functions available while a call is in progress.

Adjusting the Earpiece Volume

During a call, you can adjust the earpiece volume (and handsfree volume, if connected).

1.

During a call, press the side-up or side-down key to display the Earpiece Volume screen.

2.

Press the side-up key (or / ) to increase the volume of the call or press the side-down key (or

/ ) to decrease the volume.

Five levels (level 1 to 5) are selectable.

3.

Press when the volume is set to the desired level.

The phone returns to the in call screen automatically if left unoperated.


Putting a Call on Hold

This function allows you to manage two calls at the same time. If you wish to make another call while you are talking to someone, you can put the current call on hold to call someone else.

To Make Another Call during a Call

1.

During a call, press [Options].

2.

Select “Hold”.

The current call is put on hold.

3.

To retrieve a call, press [Options] and select

“Retrieve”.

4.

Enter the phone number you wish to make another call to, then press .

Tip

• You can also make another call by entering the phone number during a call instead of steps 1 and 2. The current call is automatically put on hold.

Call Waiting

This service notifies you of another incoming call while you have a call in progress.

1.

During a call, press [Options] and select “Hold &

Answer” to answer the second call.

The first call is put on hold and you can now talk to the second caller.

2.

Press [Options] and select “Swap Calls” to switch between the two calls.

3.

Press [Options] and select “Release Call” to end the current call and return to the held call.

Note

• You need to set “Call Waiting” to “On” if you use the

Call Waiting service (p. 92).

• Call Waiting service may not be available on all networks. Contact your network operator for more information.

• If you do not wish to answer the second call, press

[Busy], or press [Options], and select “Busy” or

“Reject”, in step 1. If “Reject” is selected, the call log of the second call is saved as a missed call.


Accessing SMS Menu During a Call

1.

During a call, press [Options] and select “Text”.

The following options are available: “Create

Message” to make an SMS, or “Inbox”, “Sent” or

“Drafts” to access these folders. For details on SMS,

see “Text (SMS)” on page 57.

Conference Call

Conference call is a call with more than 2 participants.

You may include up to 5 participants in a conference call.

To Make a Conference Call

To make a conference call, you must have one active call and one held call.

1.

During a call, press [Options] and select

“Multiparty” to answer the second call.

2.

Select “Conference All” to join the conference call.

3.

Press to end the conference call.

Note

• Conference call service may not be available on all networks. Contact your network operator for more information.

• You have more options for the Conference call in step

2:

• To put all participants on hold, select “Conf. Hold

All”.

• To put all participants except the current call on hold, select “Private”.

• To end the call with all participants, select

“Release All”.

• To disconnect from the conference call but still allow the other participants to continue talking together, select “Transfer”.

• To put the current call on hold and continue to have a conference call with the remaining participants, select “Exclude”.

• To reject adding more participants to the current party, select “Reject”, or you can send the busy tone by selecting “Busy”.


To Add New Participants to the Conference Call

1.

Press [Options] and select “Dial”.

2.

Enter the number you wish to include in the conference call and press to dial.

3.

Press [Options] and select “Multiparty”.

4.

Select “Conference All” to join the conference call.

If you wish to add other participants, repeat steps 1 to 4.

To End the Call with a Conference Call Participant

1.

During a conference call, highlight the person that you wish to disconnect from the conference call.

2.

Press [Options] and select “Release Call”.

To Have a Private Conversation with One of the

Participants

If you wish to have a private conversation with one of the participants, you may select the participant from the conference list and put the other participants on hold.

1.

During a conference call, select the person that you wish to talk to.

2.

Press [Options] and select “Multiparty”.

3.

Select “Private”.

4.

Once you have finished the private conversation, press [Options] and select “Multiparty”.

5.

Select “Conference All” to return to the conference call.

Muting the Microphone

1.

During a call, press [Mute] to mute the microphone.

To unmute the microphone, press [Unmute].


Entering Characters

When entering characters to create Contacts List entries, text messages or multimedia messages, etc., press the corresponding keys.

In multi-tap input method, press each key until the desired character is displayed. For example, press

ABC once for the letter “A” or twice for the letter “B”.

Press the following keys to:

+

: enter:

. (full-stop) , (comma) - (hyphen) ? ! ’

(apostrophe) @ :1

: enter:

(space) 0

: switch character case among four modes:

Abc, ABC, 123 and abc.

: enter other characters.

Press and hold the following keys to:

-

: enter 0 - 9 numbers.

+

Changing the Input Languages

You can change the input language on the text entry screen.

1.

On the text entry screen, press [Options].

2.

Select “Input Language”.

3.

Select the desired language.

Changing the Input Method

T9 Text Input

T9 text input method is a shortcut to enter text easily and quickly. When the T9 text input method enable, the icon appears on the text entry screen.

1.

On the text entry screen, press and hold to enter

T9 mode.

2.

Press [Options].

3.

Select “Input Method”.

4.

Select the input mode.

5.

Press each key once for any letter you require on that key.

To enter the word “How”, press .

6.

If the word shown isn’t the one you want, press or until you highlight the correct one.

7.

Press to select the word.

Entering Characters 35

36

Note

• If the correct word is not shown in step 6, enter the correct word again after switching to the multi-tap input method.

• When you are on the entry screen, there are four input modes you can choose, as follows:

: First letter upper case

: Upper case

: Lower case

: Numeric

Tip

• If you press

+

instead of step 7, a space is inserted next to the selected word.

Symbols and Punctuations

1.

On the text entry screen, press [Options].

2.

Select “Add Symbol”.

3.

Select the desired symbol.

My Dictionary

You can create your own word list for T9 text input.

1.

On the text entry screen in T9 mode, press

[Options].

2.

Select “My Dictionary”.

3.

Select “Add New Word” and enter a new word.

Entering Characters

To edit a word in the list

1.

On the text entry screen in T9 mode, press

[Options].

2.

Select “My Dictionary”.

3.

Highlight the desired word.

4.

Press [Options] and select “Edit”.

5.

Modify the word.

Using Text Templates

You can use the sentences registered in Text Templates when entering characters.

1.

On the text entry screen, move the cursor to the point you wish to insert the template.

2.

Press [Options].

3.

Select “Text Template”.

4.

Select the desired text template.

The selected text template is inserted.

Using the Menu

Accessing

Shortcut Keys

You can shortcut to the specified menus by pressing and digit keys for the menu’s corresponding number on the Main menu. See the following table for reference.

Shortcuts are listed in the headings of this manual. For example: “M 9-7”.

Example: To Access “Languages” Sub Menu

Using Shortcut Keys

Press .

Note

• The shortcut keys work for the first three menu levels only.

1.


The Main menu is displayed.

2.

Navigate to required location.

3.

Press to access function.

Using the Menu 37

Contacts (M 8)

Contacts List (M 8-1)

You can store the phone numbers and Email addresses of your friends, family and colleagues in the Contacts

List.

Depending on the size of the entry, your phone can store up to approximately 500 entries. In a Contacts

List, you can store the following items.

Items stored in the handset memory

First Name

Last Name

Tel Mobile

Tel Private

Tel Office

Email Private

Email Business

Group

Address

Note

Items stored in the SIM memory

Name: The number of characters that can be stored differs depending on the SIM card you use.

Phone: Up to 40 digits

Using the Bluetooth wireless function, you can send the

Contacts List to a PC and save to prevent loss.

Selecting the Storage Memory

“Contacts”

→

“Advanced”

→

“Memory In Use”

1.

Select Contacts location from “SIM”, “Handset” or

“Always ask”.

Tip

• “Always ask” prompts you to choose the memory every time you save a new entry.

38 Contacts

Add New Contact (M 8-2)

You can choose either the phone or SIM card memory locations to store the new entry. For switching

locationis, see “Selecting the Storage Memory” on page 38.

The amount of phone numbers that you can store to the

SIM card is dependent on its capacity. Contact your network operator for details.


→

“Add New Contact”

If you select the “Always ask” option for the memory to be used, the selection is between “To Handset” and

“To SIM”.

1.

Select the field you wish to fill in, and enter the relevant information.

2.

Press [Save] when finished.

Tip

• To create an entry, at least one field must be filled. If you create a new entry on the SIM card, you need to enter a phone number.

Setting a Group Icon to Entries

You can set group icons when storing Contacts entries so that you can easily find and edit them.


→

“Add New Contact”

→

“To Handset”

→

“Group”

1.

Select the desired group.

Adding a Thumbnail to Entries

You can attach Thumbnails to new or existing contact entries.


→

“Contacts List”

1.

Highlight the desired handset entry.

2.


3.

Press [Options] and select “Picture”.

4.

Select the desired picture.

5.


Note

• From the Contacts List entry that has a thumbnail added, you can change or delete it by selecting

“Change” or “Remove” after step 3.

• If you delete a picture in Saved Pictures, the corresponding thumbnail is also deleted.

Contacts 39

Copying a Single Entry from Handset to SIM

Card


→


1.

Select the desired entry.

2.

Press [Options] and select “Copy to SIM” or “Copy to Handset”.

3.

Highlight the desired phone number and press select.

Moving Contacts List Entries between SIM

Card and Handset


→


→

“Move all”

1.

Select “From SIM to Handset” or “From Handset to

SIM”.

The confirmation screen appears automatically, asking you if you wish to move or not.

Finding a Name and Number


→


1.

Enter the first few letters of the name.

Search results are displayed in alphabetical order.

Tip

• You can select the Contacts location from “Handset

Memory”, “SIM Memory” or “Both” before searching.

• To view the details of the item such as address, highlight the desired item, press [Options] and select

“Edit”.

Dialing from the Contacts List


→


1.

Highlight the desired entry and press .

Tip

• You can also dial from the details screen of the

“Contacts List”. On the details screen, select the desired phone number and press .

40 Contacts

Editing Contacts List Entries


→


1.

Highlight the desired entry.

2.

Press [Options] and select “Edit“.

3.

Modify the information.

4.


Deleting Contacts List Entries

Deleting All Contact Entries


→


→

“Delete All”

1.

Select “Handset Entries” or “SIM Entries”.

The confirmation screen appears automatically, asking you if you wish to delete or not.

Deleting a Contact Entry


→


1.


2.

Press [Options] and select “Delete”.

Memory Status

This function helps you to check the memory used in the Contacts List.


→


→

“Memory Status”

Speed Dial List

You can set a maximum of 8 phone numbers in the

Speed Dial List (p. 43).

Setting Contacts List Entries in the Speed Dial

List


→

“Contacs List”

1.

Select the desired entry.

2.

Highlight the desired phone number.

3.

Press [Options] and select “Add to Speed Dial”.

4.

Select the desired list number.

Tip

• The nine digit keys correspond to list numbers.

• To view the speed dial list, see page 43.

Contacts 41

Sending a Contacts List Entry


→


1.


2.

Press [Options], select “Send Contact”, and then choose “Via Bluetooth”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the entry is sent.

Receiving a Contacts List Entry

When the phone receives a Contacts List entry, a confirmation message appears.

1.

Press [Yes].

The received entry is registered in the Contacts List.

Press [No] to reject.

Tip

• For details on making Bluetooth wireless settings,

see “Connectivity” on page 88.

Call Log (M 8-3)

The phone will record the last 30 missed calls/ dialed no/ received calls.

Viewing Call Log


→

“Call Log”

1.

Press / to select the “Missed Calls”,

“Received calls”, “Dialed Calls”, or “All Calls”.

2.

Select the to show the log.

3.

Select the phone number you wish to view.

If you wish to dial the number, press .

Tip

• You can also confirm call logs by pressing during standby mode.

Saving a Call Log

1.

In the call log list, highlight the call log you wish to save as a contact entry.

2.

Press [Options] and select “Save Number”.

3.

Select “New Contact“ or “Existing Contact“.

If you select “New Contact”, you create a new

contact entry. See “Add New Contact” on page 39

for details. If you select “Existing Contact”, you add the number to an existing contact entry. See

42 Contacts

“Editing Contacts List Entries” on page 41 for

details.

Sending Messages

1.

In the call log list, highlight the call log you wish to send a message to.

2.

Press [Options] and select “Create Message”.

3.

Select “Multimedia”, “Text”, “Voice Message” or

“Video Message”.

For details on creating a message, see “Creating a

New MMS” on page 53 or “Creating and Sending a

New SMS” on page 57.

Deleting a Call Log

1.

In the call log list, highlight the call log you wish to delete.

2.


3.

Press [Yes].

Speed Dial List (M 8-4)

You can view and perform other operations for phone numbers registered in the Speed Dial List.


→

“Speed Dial List”

The names and phone numbers stored in the Speed Dial

List are displayed in order.

Accessing your Voicemail

You can access your voicemail through this menu.


→

“Speed Dial List”

→

“Voicemail”

Advanced (M 8-5)

You can copy contacts between your phone and SIM card, and check the memory status.

“Moving Contacts List Entries between SIM Card and

Handset” on page 40, and “Memory Status” on page 41

for details.

My Numbers (M 8-6)

You can check your own voice, data and fax phone numbers.


→

“My Numbers”

1.

Select the phone number you wish to check from the list.

Contacts 43

Data Counter (M 8-7)

You can confirm the amount of time spent and the bytes that you used in GPRS transmissions.


→

“Data Counter”

1.

Select from “Call Duration” or “Data Volume”.

Resetting Call Duration


→


→

“Call Duration”

1.

Select “Last data session“ or “All data session“.

2.

Press [Options] and select “Clear” or “Clear All”.

3.

Press [Yes].

Resetting Data Volume Duration


→


→

“Data Volume”

1.

Select “Last data volume“ or “All data volume“.

2.

Press [OK] and select “Sent“, “Received“, or “All”.

3.

Press [Options] and select “Clear All”.

4.

Press [Yes].

Call Charges (M 8-8)

This function lets you check the duration and charges for your calls. Some networks do not support Charging

Advice. Please check with your service provider for availability.

Checking Call Timers


→

“Call Charges”

→

“Call Timers”

Resetting Call Timers


→


→

“Call Timers”

1.

Press [Options] and select “Clear” or “Clear All”.

The confirmation screen appears automatically, asking you if you wish to delete or not.

Checking the Total Call Cost


→


→

“Call Costs”

→

“All

Calls”

The cost of all calls is displayed.

44 Contacts

Setting the Charge Rate

Set the charge rate to calculate the call cost and set the maximum limit for call cost.


→


→


→

“Set

Cost in”

1.

Enter your PIN2 code.

2.

Enter a cost per unit .

To enter a decimal point, press .

3.

Enter a currency unit (up to 3 characters).

Setting the Charge Limit

This function is useful if you wish to make sure you do not exceed a certain charge limit.


→


→


→

“Set

Limit”

1.


2.

Enter a value.


Contacts 45

Camera (M 5)

Your phone has an integrated digital camera.

This allows you to take and send pictures or video clips wherever you are.

Take Picture (M 5-1)

Put the phone into the digital camera mode to take a picture. Pictures are saved in Saved Pictures in JPEG format in the following three picture sizes.

L: 480

× 640 dots

M: 240

× 320 dots

S: 128

× 160 dots

Taking Pictures

“Camera”

→

“Take Picture”

The preview is displayed through the screen.

1.

Press to take the picture.

The shutter sounds and the still image of the taken picture is displayed. Press [Cancel] to retake a picture.

2.

Press [Save].

“Saving (file name) to My Items…” is displayed, then the picture is registered.

3.

Press to return to standby.

Remaining shots indicator

123: Indicates the remaining number of pictures that can be taken.

Using the Full Screen

The preview can be displayed on the full screen without the soft key area and indicators.

“Camera”

→


→

[Options]

→

“Full

Viewfinder”

1.


Tip

• You can also turn on or off the full screen mode by

46 Camera

Using the Zoom Function

Press or to change the zooming ratio.

Zooming ratio indicators

: Magnification.

Note

• When “Picture Size” is set to “S (128

∗

160)”, the zoom function has 3 magnifications (

×

1,

×

2,

×

4).

• When “Picture Size” is set to “M (240

∗

320)”, the zoom function has 2 magnifications (

×

1,

×

2).

Selecting the Picture Size

“Camera”

→


→

[Options]

→

“Picture Size”

1.

Select the desired picture size.

Selecting the Picture Quality

“Camera”

→


→

[Options]

→

“Picture Quality”

1.

Select “Normal” or “Fine”.

Picture quality indicators

: Fine

: Normal

Selecting the Anti-flicker Mode

“Camera”

→


→

[Options]

→

“Antiflicker”

1.

Select “Mode 1: 50Hz” or “Mode 2: 60Hz”.

Note

• Vertical stripes may occur on the picture due to the light source. Change the anti-flicker mode to rectify.

• The digital camera uses a C-MOS sensor. Although this camera has been manufactured to the highest specifications, some pictures may still appear too bright or too dark.

• If the phone has been left in a hot place for a long time before taking or registering a picture, the picture quality may be poor.

In the Case of No Available Memory

When the number of pictures that can be taken becomes

3 or less, the remaining shots indicator in the upper left of the screen turns red. (The number of pictures that can be taken is approximate.)

When the number of pictures that can be taken becomes

0, and when you try to take a picture again, “Memory full. Please delete some data!” is displayed.

Adjusting the Brightness of the Picture

According to Lighting Conditions

Press or to adjust the brightness of the picture.

Picture brightness (exposure level) indicators

→ Normal →

Dark)

Once the phone has returned to the standby screen, the brightness settings return to default.

Camera 47

Viewing the Taken Pictures

“Camera”

→


→

[Options]

→

“My

Pictures”

The list of pictures is displayed.

1.

Select the file you wish to view.

The selected picture is displayed.

Tip

• Your pictures are given file names which are

“pictureNNN.jpg” (NNN is a consecutive number).

The file name (without an extension), date and size of your pictures are displayed in the list.

Using the Timer (Delay Timer)

“Camera”

→


→

[Options]

→

“Delay

Timer”

1.


“ ” or “ ” is displayed on the screen and the phone returns to digital camera mode.

2.

Press to start the delay timer.

10 seconds after the timer sounds, the shutter sounds, and the camera takes a picture.

Note

• The countdown sounds while the delay timer is operating.

• If is pressed while the delay timer is operating, the picture is taken instantly.

• The zoom function with or , or brightness adjustment of the picture with or , is unavailable while the delay timer is operating.

• If you wish to stop taking pictures with the timer, press [Cancel] while the delay timer is operating.

Continuous Shoot

Four pictures are taken in succession. Auto Shoot and

Manual Shoot are available.

Continuous Shoot indicators

:

When pictures are taken in Continuous Shoot mode, these indicators appear on the screen.

* When delay timer and Continuous Shoot functions are simultaneously set, “ ” is displayed instead.

“Camera”

→


→

[Options]

→

“Continuous Shoot”

1.

Select “Auto Shoot” or “Manual Shoot”.

Select “Off” to cancel.

48 Camera

2.

Press to start Continuous Shoot.

Auto Shoot: Four pictures are taken in a row.

Manual Shoot: Pictures are taken one by one by pressing .

The taken pictures are saved automatically.

To stop Continuous Shoot, press [Cancel].

Note

• When “Picture Size” is set to “L (480

∗

640)” or “M

(240

∗

320)”, you cannot use the Continuous Shoot.

• When you select a frame for taking pictures, you cannot use the Continuous Shoot function.

• Delay timer cannot be used with the Manual Shoot.

Selecting a Frame

You can select the frame from preset patterns. You can also select a frame in Saved Pictures.

“Camera”

→


→

[Options]

→

“Add

Frame”

1.

Select “Preset Frames” or “My Pictures”.

2.

Select the desired frame.

The selected frame is confirmed on the display.

3.

Press .

Note

• When “Picture Size” is set to “L (480

∗

640)” or “M

(240

∗

320)”, you cannot use the Frame function.

• When you activate the Continuous Shoot, you cannot use the Frame function.

• Only images in PNG format can be selected as the frame if you select “My Pictures” in step 1. However, images larger than 128[W]

×

160 [H] cannot be used.

Selecting the Shutter Sound

You can select the shutter sound from 3 preset patterns.

“Camera”

→


→

[Options]

→

“Shutter Sound”

1.

Press or to select the desired shutter sound.

To play back the shutter sound, press [Play].

2.

Press to select the shutter sound.

Note

• Continuous Shoot uses the specialised shutter sound that cannot be changed for the above settings.

Camera 49

Record Video (M 5-2)

Put the phone into the video camera mode to record a video.

Recording Video Clips

Sound can be recorded with the video clip.

“Camera”

→


The preview is displayed through the screen.

1.

Press to start recording the video clip.

The sound for recording the video clip occurs.

If you press again, or when the recording is completed, the sound for ending the video clip recording occurs and the display transits to step 2.

2.

Select “Save”.

“Saving (file name) to My Items…” is displayed, then the video clip is registered.

To preview a video clip before saving, select

“Preview”.

To send a video clip by multimedia message after recording the video clip, select “Save and Send”.

To record a video clip again, press [Cancel].

Remaining sets indicator

123: Indicates the remaining sets of video clips that can be recorded.

Using the Zoom Function

Press or to change the zooming ratio.

Zooming ratio indicators

: Magnification.

Selecting Video Quality

“Camera”

→


→

[Options]

→

“Video

Quality”

1.

Select “Normal” or “Fine”.

Video quality indicators

: Fine

: Normal

Selecting the Anti-flicker Mode

“Camera”

→


→

[Options]

→

“Antiflicker”

1.

Select “Mode 1: 50Hz” or “Mode 2: 60Hz”.

Note

• Vertical stripes may occur on the preview screen due to the light source. Change the anti-flicker mode to rectify.

50 Camera

In the Case of No Available Memory

When the number of video clips that can be recorded becomes 3 or less, the remaining sets indicator in the upper left of the screen turns red. (The number of sets that can be recorded is approximate.)

When the number of video clips that can be recorded becomes 0, and when you try to record a video clip again,

“Memory full. Please delete some data!” is displayed.

Adjusting the Brightness of the Video Clips

According to Light Conditions

Press or to adjust the brightness of the video clip.

Picture brightness (exposure level) indicators

→ Normal →

Dark)

Once the phone has returned to the standby screen, the brightness settings return to default.

Viewing Recorded Video Clips

“Camera”

→


→

[Options]

→

“My

Videos”

The list of video clips is displayed.

1.


2.

Press .

The selected video clip is played back.

To pause playback, press .

To resume playback, press again.

To stop playback, press [Back].

Tip

• Your video clips are given file names such as

“videoNNN.3gp” (NNN is a consecutive number).

The file name (without an extension), date and size of your video clips are displayed in the list.

• If the video clip has been recorded with sound, the volume can be adjusted by pressing (or /the side-up key) or (or /the side-down key).

• The volume varies depending on the Multimedia

Volume settings (p. 87). The sound is deactivated

when “Multimedia Volume” is set to “Silent”.

Camera 51

52

Using the Timer (Delay Timer)

To Record a Video Clip with the Timer

“Camera”

→


→

[Options]

→

“Delay

Timer”

1.


“ ” is displayed on the screen and the phone returns to video camera mode.

2.

Press to start the delay timer.

10 seconds after the timer sounds, the camera starts recording the video clip.

Note

• The countdown sounds while the delay timer is operating.

• If is pressed while the delay timer is operating, the video clip is recorded instantly.

• The zoom function with or , or brightness adjustment of the video with or , is unavailable while the delay timer is operating.

• If you wish to stop recording video clips with the timer, press [Cancel] while the delay timer is operating.

Recording Video Clips with Sound

“Camera”

→


→

[Options]

→

“Voice

Record”

1.


Camera

Messages (M 4)

Your phone allows you to send and receive text, multimedia and Email, and receive WAP alerts as well.

Multimedia (MMS) (M 4-2)

About Multimedia Messaging

Multimedia Messaging Service (MMS) allows you to send and receive multimedia messages with graphical images, photographs, sound, animations or video clips attached.

Note

• Some MMS functions may not always be available depending on your network. Contact your network operator for more information.

Creating a New MMS (M 4-2-1)

→

“Multimedia”

→

“Create Message”

1.

Enter the message.

To use the text template, press [Options], then select [Text]. Move the cursor to the point you wish to insert the template. Press [Options] , select [Text

Template] and then select the desired template.

2.

Enter the phone number or Email address of the recipient.

3.

Select “Send”.

After the message is sent, the message is moved to the Sent box.

Note

• The current message size displayed while you are creating the message is an approximation.

• If a message cannot be sent for some reason, the message stays in the Outbox and “ ” is displayed on the standby screen.

Tip

• You can use the phone number or Email address from

the Contacts List. (p. 38)

To use a phone number or Email address in the

Contacts List, press [Options] and select “Contacts

List” in step 2.

• To save the message without sending, select “Save to

Drafts” instead in step 3.

• To enter the subject, select “Subject” in step 3 and enter it. Up to 40 characters as the subject (and up to

20 recipients (for To and Cc)) can be entered.

However, these may be limited depending on your network. In this case, you may not be able to send

MMS. Contact your network operator for more information.

Messages 53

• To add more recipients, select “Add Contact” in step

3. Select “To” or “Cc” and select the desired position for the recipient. Then enter the phone number or Email address.

Turning the Slide Show Setting On or Off

→


→


→

“Slide Show”

1.


If You Select “On”

• You can create messages which have up to 10 slides.

Each slide can contain one picture, one sound file and up to 2000 characters of text (up to the message total 100 Kbytes or 300 Kbytes limit).

• If you wish to add a slide to a single slide, press

[Options] and select “Add Slide”.

If you wish to perform slide operations for multiple slides, press [Options] and select “Slide Control”.

The slide control options available are:

Add: To add a new slide.

Remove: To remove the active slide.

Previous: To navigate to the previous slide.

Next: To navigate to the next slide.

If You Select “Off”

• You can attach a maximum of 1 picture, sound or video clip and up to 2000 characters of text (up to the message total 100 Kbytes or 300 Kbytes limit).

Inserting Attached Data

You can send pictures, sounds and video clips saved in the handset memory attached to multimedia messages.

→


→


→

[Options]

1.

Select from “Picture”, “Sound” or “Video”.

2.

Select from “Saved Pictures”, “Saved Sounds” or

“Saved Videos”.

3.

Select the desired file.

The selected picture/sound/video clip is attached.

When attaching is complete, press [Back] to return to the message creation screen.

• To add more files, press [Options] and select from

“Picture”, “Sound” or “Video”. Then select from

“Saved Pictures”, “Saved Sounds” or “Saved

Videos”, and select the desired file.

• To remove the attached files, press [Options] and select “Remove”.

Note

• Pictures/Sounds/Video clips protected with a copyright cannot be sent attached to a message.

• Instead of performing step 2, you can send data recorded with “Take Picture”, “Record Voice” or

“Record Video” options.

54 Messages

Reading MMS

Messages you receive are stored in the Inbox.

Incoming Messages

The MMS indicator ( ) will appear when you are receiving an incoming message.

→


→

“Inbox”

1.

Select the message you wish to view.

The message is displayed.

2.

Scroll the screen to read the message.

3.

Press when finished.

Tip




Storing the Phone Number or Email Address of a Sender in the Contacts List

→


→

“Inbox”

1.

Highlight the message from which you want to store the phone number or Email address.

2.

Press [Options] and select “Save Sender”.

For details on entering a name, see “Add New

Contact” on page 39.

Setting Up MMS

→


→


1.

Select the item you wish to set up.

• Roam. Download (Immediate, Deferred):

Controls MMS download timing when roaming outside of your network.

Immediate: Downloads MMS immediately from the server.

Deferred: Asks if you would like to download from the server.

• Home Download (Immediate, Deferred).

Controls MMS download timing at your home network.

Immediate: Downloads MMS immediately from the server.

Deferred: Asks if you would like to download from the server.

• Delivery Rep. Allow (On, Off):

Enables or disables Delivery Report when receiving a message which applies to the Delivery

Report function.

• Anonymous Reject (On, Off):

Rejects messages from an unknown or empty address name or not.

Messages 55

56

• Slide Show (On, Off):

Enables or disables Slide Show when sending a message.

• Advanced:

• Priority:

Prioritises composed messages.

• Expiry Time:

Sets Expiry Time for a message to be stored in the Server.

• Sender Visibility:

Displays the information about the sender.

• Slide Interval:

Sets the slide display time when sending a message.

• Message Size (100 KB, 300 KB):

Sets the maximum message size that can be sent.

The maximum message size that can be sent differs according to the network operator. Contact your network operator for more information.

2.

Change each item.

Sending a Picture File with Postcard

Your phone allows you to send multimedia messages to a Vodafone specific Postcard service centre that prints the picture and mail it to the recipient’s address

Messages specified in the MMS message. (Your phone is initially provided with the address of a Vodafone specific

Postcard service centre, and its address cannot be changed.)

Note

• This service is not available on some service providers. Please contact your service provider for more information.

To Create a New Postcard

→


→

“Postcard”

1.

Select “Saved Pictures”.

2.

Select a picture you wish to use for a postcard.

3.

Enter your message.

4.

Enter the following information for the recipient.

See the note below for details.

• Name • Postal Code

• Additional Info • County / City

• House No. / Street • Country

5.

Press [Options] and select “Send”.

Note

• Instead of performing step 1, you can use data taken with the “Take Picture” option.

• The items Name, House No. / Street and Postcode are necessary to complete sending Postcards.

• Information for a recipient

Name (mandatory):

Name of the recipient for a postcard up to 50 characters

Additional Info (optional):

Additional information of the recipient up to

50 characters

House No. / Street (mandatory):

Number and Street up to 50 characters

Postcode (mandatory):

Postal code up to 60 characters

County / City (optional):

State, province, and region up to 50 characters

Country (optional):

Country up to 20 characters

• The items displayed differ according to the service.

Please contact your service provider for more information. When the item, “Country” is not displayed, you cannot send Postcards overseas.

• Files in Animation GIF format cannot be used for the

Postcards service.

• The picture quality of Postcards varies depending on the picture size.

Text (SMS) (M 4-3)

About Text Messaging

The Short Message Service (SMS) allows you to send text messages of up to 1024 characters to other GSM users.

To Use SMS with Your Phone

Messages longer than 160 characters may be composed. During sending, the messages are split. If the receiver has a suitable phone the message recombines when received, if not your message will be seperated into several messages.

You can send or receive SMS even if you are talking on the phone.

You can also use Text Templates to help you compose

SMS.

Creating and Sending a New SMS (M 4-3-1)

→

“Text Message”

→


1.

Enter your message.

To use the text template, move the cursor to the point you wish to insert the template. Press

[Options] and select “Text Template” and then select the desired template.

2.

Enter the phone number of the recipient.

3.

Select “Send”.

Messages 57

The phone begins the sending process and the SMS is sent. After the message has been sent, the message is added to the Sent box.

To save the message in the Drafts box without sending it, select “Save to Drafts”.

Tip

• You can use the phone number from the Contacts

List. (p. 38)

To use a phone number in the Contacts List, press

[Contacts] in step 2.

• To add more recipients, select “Add Contact” in step

3. Select an item number for adding the recipient’s phone number. Then enter the phone number.

Reading SMS

Incoming Messages

The SMS indicator ( ) will appear when an incoming message arrives.

1.

When you receive a SMS, press during standby.

2.


The sender’s phone number and a part of the message are displayed. When the sender’s phone number is stored in the Contacts List, the sender’s name is displayed instead of the phone number.

Messages that are marked with “ ” denote unread messages. If the Inbox, Sent box or Drafts box is full, “ ” is displayed. Delete unnecessary messages.

3.


4.


Extracting Phone Numbers from the Received

Messages and Making a Call

You can make a call using the phone number embedded in the received SMS message.

→


→

“Inbox”

1.

Select the message from which you wish to extract phone numbers.

58 Messages

2.

Press [Options] and select “Extract Numbers”.

Telephone numbers embedded in the message are displayed.

3.

Highlight the phone number.

4.

Press [Options] and select “Make Call”.

To save this phone number in the Contacts List, select “Save Number”.

Setting Up SMS (M 4-3-5)

To Set Up the Service Centre Address

→


→


→

“Message

Centre”

1.

Enter the centre phone number.

If you wish to enter a country code for a message to an international number, press and hold until a

“+” sign is displayed.

Message Lifetime

This indicates the number of days and hours for which a message you send may remain undelivered to the message recipient.

During this period, the message service centre will continually try to deliver the message to the recipient.

→


→


→

“Message

Lifetime”

1.

Select the validity period.

Message Format

→


→


→

“Message

Format”

1.

Select the message format.

Connection Type

→


→


→

“Connection Type”

1.

Select the connection type.

Messages 59

60

Email (M 4-4)

About Email Messaging

The Email service allows you to send and receive Email messages and is compatible with most POP3 Email providers. Email messages of up to 2000 characters can be sent. The size of the Email messages to be received depends on Email settings.

Before You Start

You must input the specific settings for your Email provider. If you do not have a provider, please contact your network operator who may provide the correct

POP3 settings. Please note that Email settings may already be installed by your operator.

To input settings, go to “Settings”, “Network”, “Email

Settings”.

If you want to use your own existing POP3 Email provider, select an empty profile and enter the settings.

Once the settings are complete, go to “Messages”,

“Email”, “Check Email” to download new messages.

The phone will notify you if there are any new messages.

Note

• You cannot send Email messages with files attached.

If you forward Email messages with files attached, the attached files are removed.

Messages

Creating a New Email Message

→

“Email”

→


1.

Enter the message.

2.

Enter the Email address of the recipient.

3.

Select “Send”.

After the message is sent, the message is moved to the Sent box.

Note

• If a message cannot be sent for some reason, the message stays in the Outbox. To re-send the message, carry out the following:

→

“Email”

→

“Outbox”

1. Highlight the desired message.

2. Press [Options] and select “send”.

Tip

• Select “Save to Drafts” instead in step 3 to save the message without sending.

• Select “Subject” in step 3 to enter the subject. Up to

40 characters as the subject can be entered.

• Select “Add Contact” instead in step 3 to add more recipients (up to 30 recipients (for To, Cc and Bcc collectively)). Select “To”, “Cc” or “Bcc” and select or enter the desired address of the recipients.

• You can use the Email address from the Contacts

List. (p. 38)

To use an Email address in the Contacts List, press

[Options] and select “Contacts List” in step 2.

Downloading Email Messages

→

“Email”

→

“Check Email”

1.

When the Email messages have been downloaded to the phone, go to “Inbox” in “Email” to read them.

Reading an Email Message

Incoming Messages

The Email indicator ( ) will appear when there are unread messages.

→

“Email”

→

“Inbox”

1.


2.


Tip

• If you have problems downloading Email messages, please recheck the settings you have entered in

“Before You Start” on page 60.

Storing the Email Address of a Sender in the

Contacts List

→

“Email”

→

“Inbox”

1.

Highlight the message from which you want to store the Email address.

2.

Press [Options] and select “Save Sender”.

For details on entering a name, see “Add New

Contact” on page 39.

Setting Up Email (M 4-4-7)

→

“Email”

→


1.

Select the item you wish to set up.

• Download Size (Whole Message, Only Header,

Smaller than first 20KB):

Controls the download size of the Email. The

“Whole Message” option is limited to a maximum of 300 KB.

• Add Signature:

Opens the text template screen to add the signature.

• Reply Message (Incl. Original Mail, Excl. Original

Mail):

Includes or excludes the original message when replying.

Messages 61

Cell Broadcasts (M 4-8)

You can receive Cell Broadcast messages or general messages such as weather forecasts and traffic reports.

This information is broadcast to subscribers in certain network areas.

This function may not be available on all mobile phone networks. Contact your network operator for more information.

Enabling/Disabling Cell Broadcasts (M 4-8-1)

→

“Cell Broadcasts”

→

“Switch On/Off”

1.


Reading Cell Broadcast Messages (M 4-8-2)

→


→

“Read Messages”

1.

Select the desired subject.

2.


3.

Press [Back].

Setting Languages

You can select your preferred language for the cell broadcast message display.

→


→


→

“Languages”

The current language is displayed.

1.

Press .

The language list is displayed.

2.


3.

Press [Save].

Subscribing to Cell Broadcasts

Select the page of the cell broadcast message that you want.

→


→


→

“Set Info

Subjects”

1.

Select “Add/Remove”.

2.

Select the desired page.

3.

Press [Save].

Tip

• If the desired page is not in the list that appears in step 2, select “Create Subject” in step 1, then enter the subject code to add a page. For details on the subject code, contact your service provider.

62 Messages

Vodafone live!

(M 2)

Your phone is already configured to access Vodafone live! and the mobile internet*.

Vodafone live! is a new mobile internet portal which is your gateway to a new world of information, games, music and services.

Your phone uses GPRS, a system that is much faster than previous ways of getting information on a mobile phone. Also, the connection is ‘always on’ which means there is no need to wait for dialing up.

* If you have problems getting connected, please phone Vodafone Customer Support.

Your phone contains a WAP browser used for surfing on the Mobile Internet, where you can get a lot of useful information. Normally, pages are designed for a mobile phone.

Your phone is already setup to Vodafone site for WAP/

MMS Settings.

Starting the WAP Browser

1.


To Exit the WAP Browser

1.

Press to exit the browser.

•

•

•

•

Navigating a WAP Page

:

Move the highlights around in the screen.

:

:

:

Executes the option displayed in the lower centre of the screen.

Launches browser option menu.

Selects an action displayed in the lower right corner of the screen.

Used to access “Vodafone live!” by opening the browser.

Vodafone live!

63

Browser Menu

When you are browsing, you can reach browsing options by pressing [Options].

• Edit/ Select:

Selects the link you wish to see and edit. (“Select” is displayed only when the link is highlighted.)

• Homepage:

Goes to the homepage you set in the WAP Settings.

• Add Bookmark:

Adds the site you are currently browsing to your list of bookmarks.

• View Bookmarks:

Displays a list of bookmarks.

• Save Items:

Saves pictures, sounds or video clips in the appropriate My Items folder.

• Save Page:

Saves and edits the page you are currently browsing to your list of Snap Shots.

• Enter URL:

Inputs the URL of the site you wish to go to.

• Forward:

Moves to the next URL in the history list.

64 Vodafone live!

• History:

Displays a history list.

• Reload Page:

Refreshes the contents of the WAP page.

• Advanced:

• Show URL:

Displays the URL of the site you are currently browsing.

• Saved page:

Displays a list of Snap Shots.

• Push inbox:

Displays a list of WAP push messages. You can receive push messages via WAP Services.

This means that a service provider sends WAP content to your phone, without any set up.

• Settings:

Includes “Downloads”, etc.

• Security:

Sets the security.

• Clear...:

Clears history, cache, etc.

• about...:

• Exit:

Exit the WAP browser.

My Items (M 6)

My Items contains several types of picture, sound and video clip data. You can also transmit picture, sound and video clip data via Bluetooth wireless technology to

OBEX-enabled phones.

Note

• The phone can store approximately 7 Mbytes of data across Pictures, Games & More, Sounds and Videos.

Pictures (M 6-1)

Pictures that are taken by your phone’s camera or images that are downloaded from mobile internet sites can be managed.

Viewing Pictures

“My Items”

→

“Pictures”

→

“Saved Pictures”

1.


The selected picture is displayed.

Using Images as Wallpaper


→


→


The list of pictures is displayed.

1.

Highlight the file you wish to use as wallpaper.

2.

Press [Options] and select “Set as Wallpaper”.

3.

Press [OK].

Editing Pictures


→


→


1.

Highlight the file you wish to edit.

2.


3.

Select the desired option:

“Rotate”: The picture is rotated 90º anticlockwise. Press [Rotate] again for another 90º.

“Adjust Size”: Select the desired option.

“Retouch”: Select the retouching option.

“Add Frame”: Select the desired frame pattern.

“Add Stamps”: Press [Stamps] and select the desired stamp pattern. Repeat this step to add more patterns.

Note

• The size of pictures that you can retouch is 52 dots

[W]

×

52 dots [H] minimum.

• The size of pictures that you can add stamps to is 24 dots [W]

×

24 dots [H] minimum.

• Images exceeding 128 [W] or 160 [H] are saved as

128 [W]

×

160 [H] regardless of the original size.

• “Adjust Size” may not be available depending on the original picture and copyright issued.

Sending a Picture File


→


→


My Items 65

66

1.

Highlight the file you wish to send.

2.


3.

Select “As Multimedia”, “As Postcard” or “Via

Bluetooth“.


New MMS” on page 53.

Note

• The Postcard service is not available on some service providers. Please contact your service provider for more information.

• Pictures protected with a copyright cannot be sent attached to a message.

Tip

For details on transmitting My Items data, see

“Sending My Items Data” on page 67.

Saving to Contacts List

You can use this option only for pictures saved in the handset memory.


→


→


1.

Highlight the file you wish to add to Contacts List.

2.

Press [Options] and select “Add to Contact”.

To overwrite, select “Existing Contact” and select the data you wish to save to.

To save as a new entry, select “New Contact”.

My Items

For details on entering a name, see “Contacts List” on page 38.

Downloading Picture Files (M 6-1-3)


→


→

“More Pictures”

1.

The picture file download site is displayed.

Videos (M 6-2)

Video clips that are recorded by your phone’s video camera or video clips that are downloaded from mobile internet sites can be managed.

Playing Back Video Clip Files


→

“Videos”

→

“Saved Videos”

1.

Select the file you wish to play back.

2.

Press .

To resume, press again.

To stop playback, press [Back].

Note



when “Multimedia Volume” is set to “Silent”. To adjust the volume, press (or /the side-up key) or (or /the side-down key).

• Video clips exceeding 128 dots [W] or 96 dots [H] can be displayed in original or half size by pressing

[

×

1] or [

×

1/2].

Sending a Video Clip File


→

“Videos”

→


1.


2.


3.

Select “As Multimedia” or “Via Bluetooth“.



Note

• Video clips protected with a copyright cannot be sent attached to a message.

Downloading Video Clip Files (M 6-2-3)


→

“Videos”

→

“More Videos”

The video clip file download site is displayed.

Sending My Items Data

Choose the appropriate menu. See page 82

(Connectivity) for further information on Bluetooth wireless technology.


→


→



→

“Sounds”

→

“Saved Sounds”


→

“Videos”

→


1.

Highlight the desired file.

2.


3.

Select “Via Bluetooth”.


The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the file sent.

My Items 67

Note

• Pictures/Sounds/Video clips protected with a copyright cannot be sent.

• When pairing, you need to enter your passcode when establishing contact with a Bluetooth wireless technology enabled device for the first time.

Receiving the My Items Data

When the phone receives the My Items data, a confirmation message appears in the standby mode screen.

1.

Press [Yes].

The received data is registered in the corresponding

My Items folder.

Tip

• For details on Bluetooth wireless settings, see

“Connectivity” on page 88.

Games & More (M 6-3)

Along with the preloaded application, downloaded applications are stored in Applications.

Note

• Applications can store up to 10 applications.

Using Applications

Various kinds of Vodafone specific applications can be used in this phone.

To use applications, download the applications via the mobile internet.

Some applications offer the ability to connect to a network either within a game or network based application.

Note

• Applications may be both localised (no connectivity) and network based (using the mobile internet to update information/play games). The network may charge you more for using network-based applications. Please contact your service provider for more information.

68 My Items

Downloading Applications

Confirmation Screen

Before downloading the application you are asked to confirm what you are about to receive.

After checking the information on the confirmation screen, the application can be downloaded.

Note

• User authentication may be required before downloading the application on some information screens.

More Games (M 6-3-1)

“My Items“

→

“Games & More”

→

“More Games”

1.

Select the application you wish to download.

After a WAP browser screen is displayed, the confirmation screen will appear after a while.

2.

Press to start downloading.

3.


Executing Applications (M 6-3-2)


→


→

“Applications”

Downloaded applications are sequentially displayed from the latest one.

1.

Select the title of the application you wish to execute.

2.

The selected application is executed.

When using network connection type applications, connection to the network can be selected.

To end the application, press

“End”.

and select

My Items 69

Sounds (M 6-4)

The AMR data recorded by Voice Recorder is managed in Saved Sounds. The default ringtones are not contained within Saved Sounds.

: Standard MIDI format

: AMR format

: Original voice clip (AMR format recorded in

Voice Recorder)

Downloading Sound Files (M 6-4-1)


→

“Sounds”

→

“More Sounds”

The sound file download site is displayed.

Playing Back Sound Files


→

“Sounds”

→


1.

Select the file you wish to play back.

To stop playback, press .

Note

• This option may not be available in all regions.




Using the Sound Files as Ringtone


→

“Sounds”

→


1.

Highlight the file you wish to use as ringtone.

2.

Press [Options] and select “Set as Ringtone”.

The selected sound is automatically used for the ringtone of the current Profiles.

Note

• Files in AMR format cannot be used for the ringtone.

Assigning a Ringtone to Each Contact List

Entry


→

“Sounds”

→


1.

Highlight the sound you wish to use as the ringtone of the assigned contact.

2.

Press [Options] and select “Add to Contact”.

The selected sound is automaatically used when the contact call you.

70 My Items

Sending a Sound File with MMS


→

“Sounds”

→


1.


2.


3.

Select “As Multimedia”.

If you select your original ringtone in step 1, perform the following.

4.

Select the file format “MIDI”.



Note

• Sounds protected with a copyright cannot be sent attached to a message.

Bookmarks (M 6-5)

When you are browsing, press [Options] and select the appropriate option.

To Add a Bookmark

1.

Press [Options] and select “New Bookmark“.

To Access Bookmarked Pages

1.

Select the desired bookmark.

2.

Press [Options] and select “Open“.

To Edit Bookmarks

1.

Highlight a bookmarked page you want to edit.

2.


3.

Edit the title, then press .

4.

Edit the URL address, then press .

5.

Press [Options], then “Save”.

To Move Bookmarks

1.

Highlight a bookmarked page you want to move.

2.

Press [Options] and select “Move Bookmark“.

3.

Select the folder you want to place and press

[Options].

4.

Select [Open], then “Move Here“.

My Items 71

To Rename Folder

1.

Highlight a folder you want to rename.

2.

Press [Options], then select “Rename”.

3.

Change the name.

4.

Press [Options], then select “Save”.

To Delete Bookmarks

1.

Highlight a bookmarked page you want to delete.

2.

Press [Options] and select “Delete“.

Memory Status (M 6-6)

This function helps you to check the memory status of

My Items. Memory status covers Applications,

Pictures, Sounds, and Videos.


→

“Memory Status”

72 My Items

Games & More (M 1)

More Games (M 1-1)

You can download applications.


→

“More Games”

The application download site is displayed.

1.

Select the application you wish to download.

After a WAP browser screen is displayed, the confirmation screen will appear after a while.

2.

Press to start downloading.

3.


Applications (M 1-2)

The list of Java™ applications is displayed.

Downloaded applications are displayed in order starting from the latest one.

Executing Applications

For details on executing applications, see “More

Games” on page 69.

Application Detail

The application detail displays the title, version, size and description of the application for your reference.

Setting Permission

When using Java™ applications that access the network, online security for monetary transactions can be set with this option.

To Select the Function and Confirmation Method


→


1.

Highlight the desired Java™ application.

2.

Press [Options] and select “Permission”.

3.

Select “Network Access” to set how the Java™ application accesses the network.

4.

Select the desired confirmation method.

Always Connect: Allows the Java™ application access without confirmation.

First Time:

Per Session:

Informs you when the Java™ application accesses the network for the first time. If access is allowed, no more confirmations are made until you delete the application.

Informs you when the Java™ application accesses the network for the first time. If access is allowed, no more confirmations are made until the application finishes operation.

Games & More 73

Per Access: Informs you every time the Java™ application accesses the network regardless of whether or not access is allowed.

Never Connect: Prevents the Java™ application from accessing the network and no confirmation is made.

To Reset Permissions

You can reset all permissions you made


→


1.

Highlight the desired Java™ applications.

2.

Press [Options] and select “Permission”.

3.

Select “Reset Permissions”.

Settings (M 1-3)

Calls & Alarms (M 1-3-1)

You can set the priority of incoming calls and alarms while an application is operating.


→


→

“Calls & Alarms”

1.

Select “Incoming Call” or “Alarm”.

2.

Select methods.

• “Call Priority” or “Call Notice”:

The application is suspended automatically, and you can receive a call, or the alarm will sound. After finishing the call or the alarm ends, the suspend icon

( ) is displayed letting you know there is a suspended application.

• “Alarm Priority” or “Alarm Notice”:

Caller’s information is displayed on the upper part of the screen while the application continues. If you press , the application is suspended, and you can receive a call. After finishing the call, the suspend icon ( ) is displayed letting you know there is a suspended application.

74 Games & More

Sound Volume (M 1-3-2)

You can set the volume of the application such as sound

effect to one of the five levels or silent. When “Power

On Sound / Power Off Sound” (p. 87) is set to “Silent”,

this setup has priority.


→


→

“Sound Volume”

The current volume level is displayed.

1.

Press (or ) to increase the volume or press

.

(or ) to decrease the volume and then press

Backlight (M 1-3-3)


→


→

“Backlight”

→


1.

Select from “On” or “Off”.

• “On”:

• “Off”:

Lit while the application is operated.

Unlit while the application is operated even if a key is pressed.

To Set the Blink Operation

This setting enables the backlight to be controlled by the application. If set to “Off”, the backlight cannot be turned on from the application.


→


→


→

“Blink”

1.


Vibration (M 1-3-4)

When the vibration is set in the application, you can choose whether the operation is enabled or disabled.


→


→

“Vibration”

1.

Select from “On” or “Off”.

To Reset All Items in Settings Menu (M 1-3-5)


→


→

“Set to Default”

1.

Enter your handset code. The default handset code is “0000”.

Java™ Information (M 1-4)

The information about the licenses belonging to Java™ is displayed.

Games & More 75

Applications (M 3)

SIM Application (M 3-1)

You can refer to the information on the SIM. Contact your service provider for further details.

Alarms (M 3-2)

Setting the Alarms

The alarm function allows you to be alerted at a specified time.

Note that the alarm may not function correctly if the clock has not been set to the correct time.

Note

• The alarm functions even if the phone is switched off.

• The alarm will not ring when “Ringer Volume”

(p. 84) is set to “Silent”.


→

“Alarms”

1.

Select the blank setting.

2.

Enter the desired time.

To Change the Type of Alarm Tone

3.

Select “Set Alarm Tone”.

4.

Select “Tone”.

5.

Select “Preset Sounds” or “My Sounds”.

6.

Select the desired tone.

For details on selecting a tone, see “Assigning

Ringtone” on page 85.

To Change the Vibration of Alarm Tone

7.

Select “Vibration”.

8.


For details on selecting vibration, see “Vibration” on page 85.

To Change the Duration of Alarm Tone

9.

Select “Duration”.

10.

Enter the desired time (02-59).

11.

Press [Back].

To Set the Repeating Option

12.

Select “Repeat Daily”.

13.


14.

Press [Save].

76 Applications

Editing the Alarm Setting


→

“Alarms”

1.

Select the desired setting and edit it.

Resetting an Alarm Setting


→

“Alarms”

1.

Select the alarm you wish to reset.

2.

Select “Reset Alarm”.

Resetting All Alarm Settings


→

“Alarms”

→

“Clear All”

Calculator (M 3-3)

The calculator function performs the 4 arithmetic calculations using up to 9 digits.


→

“Calculator”

The calculator is displayed.

Key operations for calculation are as follows.


To enter arithemetal symbols, press 4 arrow keys and left soft key, as below:

:x :

÷

:+ ::%

To clear the entered number or operand, press

[Clear].

To do the calculations, press .

To start a new calculation, press [Clear].

Applications 77

Voice Recorder (M 3-4)

This allows you to record a voice clip of up to 30 seconds, which can be sent within a multimedia message. The recorded voice clip is registered in Saved

Sounds. Voice clips are saved in “.amr” format.

Recording a Voice Clip


→

“Voice Recorder”

1.

Press to start recording.

To stop recording before the recording time is over, press .

2.

Select “Save” to save the voice clip.

To play back the recorded voice clip, select

“Playback”.

To record a voice clip again, press [Cancel].

Note



when “Multimedia Volume” is set to “Silent”. To adjust the volume, press (or /the side-up key) or (or /the side-down key).

Tip

• You can also activate Voice Recorder by pressing

, then during standby.

Sending Voice Clips


→

“Voice Recorder”

1.

Press to start recording.

2.

Press to stop recording.

3.

Select “Save and Send”.

For details on creating a message, see “Creating a New

MMS” on page 53.

Note

• “Save and Send” is not displayed after recording in extended voice mode.

Phone Help (M 3-5)

You can view the help list and use it to guide you in the phone’s functions.


→

“Phone Help”

1.

Press

78 Applications

Calendar (M 7)

Calendar allows you to easily schedule appointments or events, which are associated with the date and time.

These entries can also be sent via Bluetooth wireless technology to a PC to share the same schedules.

Creating a New Entry

“Calendar”

1.

Highlight the desired day to which you want to add an event.

2.

Press [Options] and select “New Entry”.

3.

Select from “Appointment”, “All Day Event” or

“Anniversary”.

To Set an Appointment

1.

Select the subject field and enter the subject.

2.

Select the start time field and enter the desired time.

3.

Select the duration.

4.

Select the reminder field and select the desired option.

When selecting “Off” for the reminder option, go to step 10.

5.

Select “Tone”.

6.


7.




8.

Select “Vibration” and select from “On” or “Off”.

9.

Select “Duration” and enter the desired time.

10.

Select the location field and enter the location.

11.

Press [Save].

Note

• The reminder functions even if the phone is switched off.

• The reminder will not sound when “Ringer Volume”

(p. 84) is set to “Silent”.

Calendar 79

To Set an All Day Event

1.


2.

Select the date field and select the desired date.

3.


4.

Press [Save].

To Set an Anniversary

1.

Select the anniversary option from “Ann by Date” or “Ann by Day”.

2.

(For “Ann by Date”)


Select the date field and select the desired date

(month and day).


(For “Ann by Day”)


Select the day field and select the desired day (day of the week and month).


3.

Press [Save].

Sending a Schedule Entry


1.

Select the day including schedule entries you wish to send.

2.

Highlight the desired entry you wish to send.

3.

Press [Options] and select “Send” and “via

Bluetooth”.


The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the entry sent.

80 Calendar

Receiving a Schedule Entry

When the phone receives a schedule entry, a confirmation message appears.

1.

Press [Yes].

The received entry is registered in the Calendar.

Press [No] to reject.

Tip

• For details on making Bluetooth wireless settings,

see “Connectivity” on page 88.

Viewing an Entry


1.

Select the day you wish to view.

The daily view is displayed.

To Search By Date

1.

In the monthly or daily view, press [Options].

2.

Select “Go to”.

3.

Select “Today” to display today or “Enter date” to enter the desired date.

To Search By Subject

1.


2.

Select “Find”.

3.

Enter the desired text.

To Change the Week Format

1.

In the monthly view, press [Options].

2.

Select “Week Format”.

3.

Select “Monday-Sunday” or “Sunday-Saturday”.

Deleting Entries

1.


2.

Select “Delete”.

3.

Select the desired option.

• “This Appointment” (daily view only):

Deletes the selected appointment.

• “All This Day”: Deletes all entries for the selected day.

• “All This Month”: Deletes all entries for the selected month.

• “Up to Last Month”:

Deletes all entries before this month.

• “All Schedules”: Deletes all entries in this application.

Calendar 81

Settings (M 9)

Setting the Display (M 9-1)

You can change the settings of the screen.

Wallpaper (M 9-1-1)

For the standby screen, 3 pictures are provided.

Pictures taken with the digital camera or images downloaded from a WAP site can be used for wallpapers.

Setting My Pictures


→

“Display”

→

“Wallpaper”

→

“My

Pictures”

1.


2.

After displaying the picture, press .

3.

Specify the area you wish to display using the navigation keys.

Note

• Some pictures cannot be used because of their picture and data types.

Assigning the Pictures (M 9-1-2)

Pictures can be displayed when turning the power on or off, when receiving an incoming call, or when operating the alarm.

Pictures taken by a digital camera or images downloaded from a WAP site can be used.

To Set Built-in Pictures


→

“Display”

→

“Graphics”

1.

Select the desired situation to set the picture.

2.

Select “Preset Animation” when you select “Power

On” or “Power Off” in step 1.

Select “Pattern 1”, “Pattern 2” or “Pattern 3” when you select “Alarm” in step 1.

To Set My Pictures


→

“Display”

→

“Graphics”

1.

Select the desired situation to set the picture

2.

Select “My Pictures”.

3.


4.

After displaying the picture, press .

5.

Specify the area you wish to display using the navigation keys.

Note

• Some pictures cannot be used because of their picture and data types.

82 Settings

Setting the Greeting Message (M 9-1-3)

You can set the message which will appear when the phone is turned on.


→

“Display”

→

“Greeting Message”

1.

Select “Switch On/Off”.

2.


3.

Select “Edit Message” and enter the message.

Up to 16 characters can be stored as a message.

For details on entering characters, see “Entering

Characters” on page 35.

Showing the Clock (M 9-1-4)

You can display the current date and/or time on the standby screen.


→

“Display”

→

“Show Clock”

1.

Select from “Time Only”, “Date & Time” or “Off”.

Backlight (M 9-1-5)

You can turn the backlight of the screen on or off when you press the keypad or the optional Cigarette Lighter

Charger is connected to the phone.

You can change the time the backlight is on for, which will help conserve battery life.

Tip

• When you purchase this phone, Backlight is set to 10 seconds.

To Select the Backlight Time Out


→

“Display”

→


→

“Time

Out”

1.

Select the desired time.

Select “Off” to turn it off.

Adjusting the Brightness of the Backlight

(M 9-1-6)

You can adjust the brightness of the backlight of the screen from 4 levels.


→

“Display”

→

“Brightness”

1.

Adjust the brightness by pressing (Light) and

(Dark) for maximum clarity.

2.

Press .

Display Setting Reset (M 9-1-7)

The display settings can be reset to their default settings.


→

“Display”

→


1.


Settings 83

Sound (M 9-2)

You can use this menu to check or edit the current

Profiles settings.

Profiles (M 9-3)

Tone sound and vibration settings can be customised for each profile according to your environment.

There are 5 profiles including one user definable profile: Normal, Meeting, Activity, Headset and Silent.

Activating a Profile


→

“Profiles”

1.

Select the desired profile.

Note

• When a profile is set, the corresponding icon

described on page 27 is displayed on the standby

screen.

Tip

• Press and hold to switch Profiles settings between Normal and Silent mode during standby.

Customising Profile


→


1.

Highlight the profile you wish to customise.

2.

Press [Options] and select “Personalise”.

3.

Select the setting you wish to customise and change as desired.

For details about settings, see pages 84 to 88.

4.


Resetting Profile Settings


→


1.

Highlight the profile you wish to reset.

2.

Press [Options] and select “Set to Default”.

3.


Ringer Volume

You can adjust the ringer volume to one of 6 levels or a step tone.


→


1.


2.


3.

Select “Ringer Volume”.

The current volume level is displayed.

84 Settings

4.

Press (or ) to increase the ringer volume or press (or ) to decrease the ringer volume and then press .

To select “Step Tone”, press (or ) at level 5.

To select “Silent”, press (or ) at level 1.

Assigning Ringtone

You can select the ringtone from 28 tones including 5 patterns, 3 alerts, 10 sound effects and 10 melodies. You can also select a sound in Saved Sounds as the default ringtone excluding the AMR format.


→


1.


2.


3.

Select “Assign Ringtone”.

4.


5.

Select the ringtone you wish to use.

To hear the demo play, press . To stop playing,

6.

Press [Options] and select “Assign”.

Note

• If you delete a ringtone that uses a sound in Saved

Sounds, the default ringtone is set.

Vibration

When the vibration option is set on, the phone will vibrate for incoming calls regardless of the ringer volume and tone settings.


→


1.


2.


3.

Select “Vibration”.

4.

Select from “On”, or “Off”.

Alerts

You can personalise profiles for alerts including warning tone, message alert and low battery alert.

Settings 85

Warning Tone

Your phone emits the warning tone when an error occurs.


→


1.


2.


3.

Select “Alerts”.

4.

Select “Warning Tone”.

5.


6.


7.

Select “Volume” and select from “High”, “Middle” or “Low”.

8.

Select “Tone” and select “Preset Sounds” or “My

Sounds”.

9.




Message Alert

When receiving messages, special ringtones can be set.


→


1.


2.


3.


4.

Select “Message Alert”.

5.

Select from “Multimedia”, “Text” or “WAP”.

6.

Select “Volume” and select the desired volume.

7.

Select “Sound” and select “Preset Sounds” or “My

Sounds”.

8.

Select the desired ringtone.

For details on selecting a ringtone, see “Assigning


9.

Select “Vibration” and select from “On”, or “Off”.

For details on selecting vibration, see “Vibration” on page 85.

86 Settings

Low Battery Alert

Adjust the volume of the alert when the battery becomes low.


→


1.


2.


3.


4.

Select “Low Battery Alert”.

5.

Select from “High”, “Middle”, “Low” or “Silent”.

Keypad Tones

When the keypad tone is set on, you will hear a confirmation tone each time a key is pressed.


→


1.


2.


3.

Select “Keypad Tones”.

4.


5.


6.

Select “Volume” and select from “High”, “Middle” or “Low”.

7.

Select “Tone” and select from keytone 1, keytone 2, keytone 3 and key tone 4.

8.


For details on selecting the tone, see “Assigning


Power On Sound / Power Off Sound

The phone can be set to emit a sound when it is switched on or off. You can define the volume, duration and the melody to be used for this task.


→


1.


2.


3.

Select “Power On Sound” or “Power Off Sound”.

4.


5.


6.

Select “Volume” and select the desired volume.

7.

Select “Sound” and select “Preset Sounds” or “My

Sounds”.

8.

Select the desired sound.

For details on selecting a sound, see “Assigning


Settings 87

88

Connectivity (M 9-4)

By configuring the settings in this menu, you can connect to Bluetooth wireless technology enabled phones, as well as PCs.

Using the Bluetooth Wireless Function (M 9-4-1)

To Turn On or Off


→

“Connectivity”

→

“Bluetooth”

→


1.


The Bluetooth wireless setting is activated, and

“ ” is displayed.

To Search for Devices to be Paired

For using the Bluetooth wireless function, you need to search for other Bluetooth wireless technology enabled devices to establish contact with your phone. Keep your phone within a distance of 10 metres before searching.


→


→


→

“Search for Devices”

The phone starts searching for devices within 10 metres.

1.

Select the desired device for pairing.

2.

Enter the device passcode.

Note

• Pairing means “Authentication”.

Settings

• The users of two devices with Bluetooth wireless technology should agree on the same passcode for both devices in order to pair them.

• The passcode is used just once, there is no need to remember it. The passcode can be different each time the devices are connected.

• Devices that do not have a user interface have a factory-set passcode (i.e. headsets and car kits - see the device user guide).

• If the Bluetooth wireless function is off before searching, the phone turns the Bluetooth wireless function on automatically and starts searching.

• When you wish to perform the device search again, the device list where all devices searched will be displayed when selecting “Search for Devices” again in step 1. Highlighting “New Devices” at the top of the list and pressing will resume the new search and refresh the list.

• You can only select one device for pairing. To change the paired device else, see “Handsfree Devices“ on this page.

Handsfree Devices

You can activate, rename, and delete the paired handsfree device in the list.

To Activate a Device


→


→


→

“Handsfree Devices”

1.

Select the device you wish to activate.

To Rename a Device


→


→


→


1.

Highlight the device you wish to rename.

2.

Press [Options] and select “Change Name”.

3.

Rename the device.

To Clear a Device Name


→


→


→


1.

Highlight the device you wish to clear.

2.


Paired Devices

You can rename and delete the paired device in the list.

To Rename Your Phone

You can rename your phone. The name is shown on other devices when your phone is detected.


→


→


→


→

“Device Name”

1.

Enter the new device name.

To Show or Hide Your Phone


→


→


→


→

“Visibility”

1.

Select the desired visibility settings.

“Show My Phone”: Allows other devices to recognize your phone.

“Hide My Phone”: Hides your phone from other devices.

To Turn Off Automatically


→


→


→


→

“Bluetooth Time Out”

1.


Your phone turns the function off automatically in the specified time.

Bluetooth Wireless Settings

With this setting you can rename your phone, prevent other devices from recognising your phone, and turn the

Bluetooth wireless function off automatically to save battery power, etc.

Settings 89

PC Software (M 9-4-2)

By connecting your phone to a PC, you can transmit pictures, sounds, video clips, and Contacts List entries.

Follow the procedure to select the connection method

(Bluetooth wireless or USB connection).


→


→

“PC Software”

1.

Select the desired connection type from “Data

Cable” or “Bluetooth”.

Date & Time (M 9-5)

You need to set the correct time and date in order for your phone’s various time-based functions to work correctly.


→

“Date & Time”

→

“Set Date/Time”

1.

Enter the day, month, year and time using the digit keys.

Tip

• When you enter the time in the 12-hour format, press

to switch between am and pm. The order in which the date and time is displayed is based on the format setting.

Selecting the Time Format


→


→

“Time Format”

1.

Select “12 hour” or “24 hour”.

Selecting the Date Format


→


→

“Date Format”

1.

Select from “D.M.Y”, “M-D-Y”, or “Y/M/D”.

Setting the Daylight Saving


→


→

“Daylight Saving”

1.


90 Settings

Setting the Time Zone


→


→

“Time Zone”

→

“Change Zone”

1.

Press or to select the home city to set.

Customising the Time Zone


→


→

“Time Zone”

→

“Set

Custom Zone”

1.

Enter the time-zone differences using the digit keys.

Pressing switches between – and +.

Call Settings (M 9-6)

Set various types of functions and services.

Diverts (M 9-6-1)

This service is used to divert incoming calls to your voice mail system or to another number depending on certain conditions where you cannot answer a call.

To Divert Calls


→


→

“Diverts”

1.

Select one of the following options.

• “All Calls”: Diverts all voice calls without ringing.

• “When Busy”: Diverts incoming calls when you are on a call.

• “No Answer”: Diverts incoming calls if you do not answer a call within a certain period of time.

• “Not Reachable”: Diverts incoming calls when your phone is out of network service or switched off.

2.

Select “On”.

Settings 91

92

3.

Enter a phone number to which you wish to divert

calls or search for it in the Contacts List. (p. 38)

To use a phone number in the Contacts List, press

[Contacts].

4.

Press .

If you select “No Answer” in step 1:

5.

Select the period of time from 6 levels (05 to 30 seconds).

Note

• When “All Calls” diverts set to “On”, “ ” is displayed on the standby screen.

Tip

• If you select “By Service” in step 2, you can select further divert options.

To Check the Divert Status


→


→

“Diverts”

1.

Select the divert option you wish to check.

2.

Select “Status”.

You can check the status of the selected divert option.

To Cancel All Divert Settings


→


→

“Diverts”

→

“Cancel

All”

Settings

Call Waiting (M 9-6-2)

If you wish to be able to receive another incoming call while you have a call in progress, you must activate the

Call Waiting service.


→


→

“Call Waiting”

1.

Select “On”, “Off” or “Status“.

Note

• The Call Waiting service may not be available on all mobile phone networks. Contact your network operator for more information.

Showing Your Phone Number (M 9-6-3)

This lets you control whether to show your phone number when calling another party or not.


→


→

“Show Your

Number”

1.

Select “On”, “Off” or “Status“.

Note

• Some networks do not support this service. Please check with your service provider for availability.

Restrict Calls (M 9-6-4)

This function lets you place restrictions on incoming and outgoing calls. To activate this option you will need the specified password, which is available from your service provider.


→


→

“Restrict Calls”

1.

Select from “Outgoing Calls” or “Incoming Calls”.

• Outgoing Calls:

• Incoming Calls:

Restricts outgoing calls.

Restricts incoming calls.

2.


(For “Outgoing Calls”)

• Bar Foreign Calls: Restricts all outgoing international calls.

• Bar All Outgoing Calls:

Restricts all outgoing calls except emergency calls.

• Only Local & Home: Restricts all outgoing international calls except to your home country.

(For “Incoming Calls”)

• Bar All Incoming Calls:

Restricts all incoming calls.

• Bar if Abroad: Restricts all incoming calls when you are outside of the coverage from your registered network operator.

3.


• “All Services”:

• “Voice Calls”:

• “Data”:

• “Fax”:

Restricts all services.

Restricts all voice calls.

Restricts all data calls.

Restricts all fax calls.

• “All Except Msgs”: Restricts all services except messages.

4.


5.

Enter the network password.

To Cancel Settings


→


→


1.

Select “Outgoing Calls” or “Incoming Calls”.

2.

Select “Cancel All”.

3.

Enter the network password.

Settings 93

94

Fixed Dialing No.

This option is available on most SIM cards of GSM mobile phones. It allows you to configure a SIM card so that it can only be used to make calls to the numbers of a predefined list.

To Enable Fixed Dialing No.


→


→


→

“Fixed Dialing No.”

1.

Enter your PIN2 code. Pin2 is a second PIN code used to unlock certain features of a SIM card, such as Fixed Dialing and Call Cost metering. Not all

SIM cards use the PIN2 code.

2.


3.


To Add a New Name


→


→


→

“Fixed Dialing No.”

1.


2.

Select “Edit Dial List”.

3.

Press [Options] and select “Add New Contact”.

4.

Add a name and a phone number.

For details on adding a name and a phone number,

see “Add New Contact” on page 39.

5.

Press [Save].

Settings

Changing the Network Password


→


→


→

“Change Password”

1.

Enter the old network password.

2.

Enter the new network password.

3.

Enter the new network password again.

If you enter the incorrect password, you are asked to enter the password again.

4.

Press .

Auto Redial (M 9-6-5)

See “Automatic Redialing” on page 30.

Minute Minder (M 9-6-6)

Minute Minder function informs you of your talk time by sounding a tone after every minute.


→


→

“Minute Minder”

1.


Call Setting Reset (M 9-6-7)

The call settings can be reset to their default settings.


→


→


1.


Changing the Language (M 9-7)

You can change the language that the phone uses to display messages.


→

“Languages”

1.


Tip

• You can also change the input language on the text

entry screen (p. 35).

Note

• If you select “Automatic” in step 1, the language preset on the SIM card is selected.

• If the language preset on the SIM card is not supported, then the default language of the phone is selected.

Network (M 9-8)

Network Settings (M 9-8-1)

To Select a Network Automatically

Each time the power is turned on, your phone always tries to connect to the preferred network.

If your phone does not connect to the network, you can perform the following to establish the preferred network connection.


→

“Network”

→

“Select Network”

→

“Automatic”

To Set the Network Manually


→

“Network”

→


→

“Manual”

1.

Select the desired network.

To Add a New Network


→

“Network”

→


→

“Set

Preferred”

If there is no entry, perform the following steps.

1.

Press “Add New” and then select the name of the network you wish to add.

Settings 95

If there is an entry, perform the following steps.

1.

Press [Options] and select “Insert“.

2.

Choose the name of the network you wish to add.

3.

Press [Selecct].

To Change the Position of a Network in the

Preferred List


→

“Network”

→


→

“Set

Preferred”

1.

Select the name of the network to change the position in the list.

2.

Select “Add to end”.

To Delete a Network from the Preferred List


→

“Network”

→


→

“Set

Preferred”

1.

Select the name of the network you wish to delete.

2.

Press [Options] and select “Delete“.

3.

Press [Yes].

WAP/MMS/Email Settings

Note

• In normal operation, you do not need to change settings.

WAP Settings (*: Item to be set is mandatory)

“Profile Name”*: WAP profile name (Unique name)

“IP Address”*: IP address for WAP

“Homepage”: Homepage

“Port Number”*: Security option (0-65535)

“Connection Type” :

Bearer connection type (“GPRS

Then CSD”, “GPRS” or “CSD”)

“GPRS Settings”:

“APN”*: Access point name

“Password”: Password

“CSD Settings”:

“Phone No.”*: Access point number

“Line Type”: Line type (“ISDN” or “Analogue”)

“Username”: User name


96 Settings

MMS Settings (*: Item to be set is mandatory)

“Profile Name”*: MMS profile name (Unique name)

“IP Address”*: IP address for MMS

“Relay Server URL”*:

MMS relay server

“Port Number”*: Security option (0-65535)

“Connection Type”:Bearer connection type (“GPRS



“APN”*: Access point name


“CSD Settings”:

“Phone No.”*: Access point number


“Username”: User name


Email Settings (*: Item to be set is mandatory)

“Profile Name”*: Email profile name (Unique name)

“Email Address”*: Email address

“Return Address”: Email address to which the Email message is returned when sending fails

“POP3 Server”: Server for receiving Email messages

“Server Name”*: Server name

“User ID”*: User ID

“Password”*: Password

“Port Number”: Security option (0-65535)

“SMTP Server”: Server for sending Email messages

“Server Name”*: Server name

“User ID”: User ID


“Port Number”: Security option (0-65535)

“Authentication”: Authentication (Off, POP before

SMTP, SMTP)

“Primary DNS”: Primary DNS

“Secondary DNS”: Secondary DNS

Settings 97

“Connection Type”:Bearer connection type (“GPRS



“APN”*: Access name


“CSD Settings”:

“Phone No.”*: Telephone Number



To Activate the WAP/MMS/Email Profile


→

“Network”

1.

Select from “WAP Settings”, “MMS Settings” or

“Email Settings”.

2.

Select the desired profile.

To Edit the WAP/MMS/Email Profile


→

“Network”

1.



2.

Highlight the desired profile.

3.


4.

Edit the desired item.

To Copy the WAP/MMS/Email Profile


→

“Network”

1.



2.


3.

Press [Options] and select “Copy”.

4.

Edit the new profile name.

98 Settings

To Delete the WAP/MMS/Email Profile


→

“Network”

1.



2.


3.


Security (M 9-9)

Auto Keypad Lock (M 9-9-1)

By setting this option on, your phone will lock the keypad automatically after the desired time if no operation is performed.


→

“Security”

→

“Auto Keypad Lock”

1.


Select “Off” to turn it off.

Enabling/Disabling the PIN Code (M 9-9-2)

If the PIN code is enabled you are asked to enter the

PIN code each time the phone is switched on. Your PIN code is stored on the SIM card and you should have been made aware of the code when you purchased the

SIM card. Contact your service provider for further details.


→


→

“PIN Entry”

1.

Select “On” to enable the PIN code.

Select “Off” to disable it.

2.

Enter your PIN code.

Note

• If you enter the wrong PIN code three times in step 2, the SIM card will lock. To remove the lock, contact your service provider/SIM card vendor.

Settings 99

To Change PIN Code

This allows you to change the PIN code stored on the

SIM card. Before you change the PIN code, select “On”

in step 1 in “Enabling/Disabling the PIN Code” on page 99.


→


→

“PIN Entry”

→

“Change

PIN”

1.

Enter the existing PIN code.

2.

Enter a new PIN code.

3.

Enter the new PIN code again.

Changing PIN2 Code (M 9-9-3)

Pin2 is a second PIN code used to unlock certain features of a SIM card, such as Fixed Dialing and Call

Cost metering. Not all SIM cards use the PIN2 code.


→


→

“Change PIN2”

1.

Enter the existing PIN2 code.

2.

Enter a new PIN2 code.

3.

Enter the new PIN2 code again.

Handset Lock (M 9-9-4)

The Handset Lock is an additional security feature which prevents unauthorised use of the phone or certain features.


→


→

“Handset Lock”

1.


2.


Master Reset (M 9-10)

All settings can be reset to their default settings.


→

“Master Reset”

1.


100 Settings

Connecting GX18 to Your PC

You can use the following functions by connecting the

GX18 to your PC using an USB port* or Bluetooth wireless technology port:

• GSM/GPRS modem

• CAMagic Mobile for GX18

* Requires an USB Data Cable for USB port connection.

System Requirements

Operating System:

Windows

®

2000*, Windows

®

XP**, Windows

Vista

* Service Pack 4

** Service Pack 2 or later

Supported Software:

Microsoft

®

Outlook

Interface:

USB port or Bluetooth wireless port

CD-ROM drive

For details, see the User Guide Software which is installed within CAMagic Mobile or our web-site, http://www.sharp-mobile.com.

CAMagic Mobile

You can transmit the following items between your phone and your PC, and can use Contacts List entries on your PC.

• My Items files (pictures/sounds/video clips)

• Contacts List entries

• Short messages

• Schedule entries

Note

• Some large files may not be able to be transmitted from the PC to the phone.

• Applications (Camera, My Items, etc.) do not run when the phone is connected to the PC via Bluetooth wireless technology interface or USB Data Cable, you need to uninstall the previous one.

• If you have already installed Sharp CAMagic Mobile, you need to uninstall the previous one.

• If you have trouble with installation, uninstall

CAMagic Mobile, restart your PC, reinstall

CAMagic Mobile and restart.

• Connecting your phone to your PC via the USB Data

Cable may not charge the battery. To charge the battery, always use the AC Charger recommended by the manufacturer.

Connecting GX18 to Your PC 101

Troubleshooting

Problem

The phone does not turn on.

PIN code or PIN2 code is rejected.

The SIM card becomes locked.

The display is difficult to read.

Solution

• Make sure the battery is properly inserted and charged.

• Make sure you have entered the correct code (4 to 8 digits).

• Your SIM card/protected functions will become locked after 3 unsuccessful attempts.

• Contact your SIM provider if you do not have the correct

PIN code.

• Enter PUK code (8 digits) provided by your service provider (if supported).

• If the attempt is successful, enter the new PIN code and confirm your phone is operational again. Otherwise contact your dealer.

• Adjust the backlight brightness for the display.

Problem

Phone functions do not work after the phone is turned on.

Calls cannot be made or received.

Solution

• Check the radio signal strength indicator as you may be outside the service area.

• Check to see if any error message is displayed when you turn your phone on. If so, contact your dealer.

• Make sure the SIM card is correctly inserted.

• If the message “SIM card error” is displayed at start-up, you cannot use your SIM card or the SIM card is damaged.

Contact your dealer or network service provider.

• Check your call barring, fixed dialing setting, remaining battery and call forwarding settings.

• Check if your phone is currently performing data communication using Bluetooth wireless technology interface or a USB

Data Cable.

• Check the remaining balance if you are using a pre-paid

SIM card.

102 Troubleshooting

Problem

Call quality is poor.

Cannot access network service.

Cannot send or receive Text

Messages.

Cannot connect to

Multimedia

Message service provider.

Solution

• Your current location may not provide good call quality (i.e., in a car or train). Move to a location where radio signal strength is greater.

• Check where your account has been registered and where the service is available.

• Make sure you are correctly subscribed for the Short

Message Service, that the network supports this service, and that the Message Centre number is set up correctly. If not, contact your network service provider.

• MMS settings and configuration may be missing or incorrect or the network does not support it. Check your service provider’s access point number.

Contact your service provider to confirm the correct settings.

Problem

Limited memory available.

Call is terminated unexpectedly.

No entries are displayed in the

Contacts List

Fax transmission failure

Cannot receive

OBEX data.

Solution

• Delete any unnecessary data.

• Magnetised objects such as health necklaces placed near the phone may terminate the call. Keep your phone away from such objects.

• Confirm that the Contacts

Location setting (Handset or

SIM) and View Groups setting are correct.

• Before transmitting fax data, configure your fax software to use the software flow control.

• Use of a data cable is recommended for transmitting fax data.

• The OBEX data can only be received during standby. The message “Please return to standby.” is displayed.

http://www.sharp-mobile.com

Troubleshooting 103

104 Troubleshooting

Index

A

Accessories 19

Alarms 76

B

Battery 22

Bluetooth wireless function 88

C

Calculator 77

Calendar 79

Call Costs 44

Call functions 29

Answering 30

Call Waiting 32

Conference Call 33

Earpiece volume 31

Making 29

Muting 34

Putting on hold 32

Redialing 30

Speed dialing 29

Call Log 42

Call settings 91

Auto Redial 94

Call Waiting 92

Diverts 91

Minute Minder 94

Resetting 94

Restrict Calls 93

Show Your Number 92

Cell Broadcasts 62

Centre key 20, 26

Contacts List 38

Changing the list 38

Creating 39

Deleting 41

Dialing 40

Editing 41

Finding 40

Memory Status 41

Receiving an entry 42

Selecting the storage memory 38

Sending an entry 42

D

Data Counter 44

Date & Time 95

Digital camera 46

Display indicators 26

Display language 95

Display settings

Backlight 83

Brightness of backlight 83

Greeting message 83

Resetting 83

Showing the clock 83

Wallpaper 82

E

Earpiece volume 31

Email 60

Creating 60

Reading 61

Setting Up 61

Storing the Email Address of a

Sender in a Contacts List

61

Emergency calls 29

H

Handset code 100

Handset Lock 100

I

Input languages 35

Input method 35

International calls 29

J

Java™ applications 73

K

Keypad Lock 26

Index 105

106

L

Left soft key 21

M

Master Reset 100

Memory Status 41

Memory status 72

Menu and shortcut 37

Multimedia message 53

Creating 53

Inserting attached data 54

Reading 55

Sending with Postcard 56

Storing the phone number or

Email address of a sender in the Contacts List 55

Turning the slide show setting on or off 54

My Numbers (Voice/Data/Fax) 43

N

Navigation keys 20

Network settings 95

P

PC Software 90

Phone Help 78

Picture file 65

PIN code 99

Index

PIN2 code 100

Power on and off 25

Profiles

Activating 84

Alerts 85

Customising 84

Keypad tones 87

Multimedia Volume 87

Power Off Sound 87

Power On Sound 87

Resetting 84

Ringer volume 84

Ringtone 85

Vibration 85

R

Right soft key 21

S

Screensavers 74

Security 99

Auto Keypad Lock 99

Changing PIN2 code 100

Enabling/Disabling PIN code 99

Handset Lock 100

SIM Application 76

SIM card 22

Sound file 70

Speed Dial List 43

T

Text message 57

Creating 57

Extracting phone numbers 58

Reading 58

Setting up 59

Troubleshooting 102

V

Video camera 50

Video clip file 72

Vodafone live! 63

Voice mail key 21

http://www.sharp-mobile.com

No results