iScan Duo owner’s manual available online at www.dvdo.com
If any items are missing or damaged, please notify your dealer immediately.
•
•
•
•
•
•
•
iScan Duo Video Processor
Universal 12V@5A AC-to-DC Power Converter
US IEC Power Cord (International Customers, consult your local authorized DVDO reseller)
Remote Control
Serial Cable for Automation Rackmount Kit
USB Cable
Check the components
Notice: The information contained on this Quick Start card, including but not limited to any product specifications, is subject to change without notice.
v Review the documentation for important information.
Remove the components and iScan Duo from the box.
Save the packing materials in case you need them later.
u
Unpack the box
DUAL OUTPUT HIGH-DEFINITION VIDEO PROCESSOR
Q U I C K
S T A R T
G U I D E
Troubleshooting
1. What should I do if my iScan Duo is not functioning correctly?
Restore the iScan Duo to its factory default state.
a. Using the remote control:
• Press the MENU button
• Press the
q button until the FPD shows Configuration
• Press ENTER
• Press the
q button until the FPD shows Factory Defaults
• Press ENTER
• Press the
q button until the FPD shows All Defaults
• Press ENTER
• Press the
q button to select Yes
• Press ENTER
The iScan Duo will be restored to its factory default state.
b. Using the buttons on the front panel:
• Apply power to the iScan Duo
• Press the MENU, EXIT and POWER buttons simultaneously until
the FPD shows Factory Default — Please wait . . .
2. Why is the blue Status LED blinking on the front panel of my iScan Duo?
The Status LED on the iScan Duo will blink blue if it is processing an HDCP
protected signal on its HDMI inputs and it is unable to authenticate with
the display. Verify that your display is HDCP-compliant. If your display
is not HDCP-compliant then you will need to use the analog connections
from your source. If your display is HDCP compliant, check your cabling
and try new cables, if possible, or try cycling the power on your display or
HDCP source to force reauthentication between your display and source.
3. Will I lose the settings on my iScan Duo if I update the
software version?
The iScan Duo will typically not lose its settings after performing a software update. DVDO will inform users if a software update will erase the
iScan Duo’s settings. Please take note of your settings before updating
your software.
Questions?
Contact us directly at [email protected] or by phone at:
Toll-Free: 1-888-651-1765
(Monday - Friday, 9 am to 5 pm PST)
www.dvdo.com
DVDO-QS-1000
Front and Back Panel
Status LED
IR Window
Front Panel Display (FPD)
Menu
Enter
Navigation Buttons
Up
Exit
EXIT
MENU
Power
Left
Down Right
Digital Audio Inputs
Video 3
VIDEO 3
Analog Audio Inputs
1&2
Component 1 Video 1
Y (G)
Pb (B)
Pr (R)
1
1
VIDEO/S
2
1
2
12V Triggers
1&2
2
2
L
Component 2 Video 2
SERIAL PORT
AUDIO
D I G I TA L
1
Serial Port
2
R
ANALOG AUDIO INPUTS
VGA
HDMI Audio
Output
12VDC 50mA MAX
3
1
R
2
3
ANALOG VIDEO INPUTS
S-Video
Optical Digital
Output
1
L
S-VIDEO
Optical
1–3
Coaxial
VGA Port
AUDIO
4
INPUTS
5
AUDIO
6
12VDC 5A
T RIGGER OUT
OUT
7
8
1
2
HDMI INPUTS
HDMI OUTPUTS
HDMI Inputs
1–8
HDMI Outputs
1–2
IN
USB
OUT
IR
Mini USB Remote
Port
Control
Jacks
POWER
Power
Quick Note
This Quick Start Guide has been created to assist you in the first step of setting up your iScan Duo system. It involves displaying the iScan
Duo’s On Screen Display (OSD) on your screen.
Using the iScan Duo’s OSD allows the user to navigate the menu system, and lets the user know that the iScan Duo is sending a compatible
signal to the display. If the OSD is not visible on the display’s screen by pressing one of the sub-menu buttons on the remote control, then
the iScan Duo’s output must be configured to work with the input that is being used on the display. Following all of the steps provided should
allow you to see the OSD.
To best set up your iScan Duo unit with your display, we recommend that you consult the iScan Duo Owner’s Manual (available online) – Section
3 – Setup.
Instructions in bold apply to specific buttons on either the front panel or remote control of the iScan Duo. Instructions in italics (top line /
bottom line) apply to information that is displayed on the Front Panel Display (FPD).
STEP 1 - Powering Up
Attach the removable power cord to the external power supply. Plug the removable power cord into a wall outlet or power conditioner, if
applicable. Plug the small connector attached to the cable that comes out of the power supply into your iScan Duo. Your iScan Duo should
PRindicating that there
Y will turn
PB red
B PB/CB H/Cs
R PR/C
R Gno
Y active
power on and display iScan Duo — DVDO on the FPD. The Status LED on your iScan Duo
are
inputs detected.
V
STEP 2 - Connecting the iScan Duo in your system
Displays with a Digital Input (HDMI or DVI-D)
Y
HDMI
PB
PR
R PR/CR G Y
B PB/CB H/Cs
DVI-D
HDMI is backwards compatible with DVI-D with the use of either a cable or adapter. Connect the iScan Duo’s HDMI 1 output to your display.
If your display has an HDMI input, use an HDMI-to-HDMI cable. If your display has a DVI-D input, use an HDMI-to-DVI cable or adapter.
The default output on the iScan Duo is HDMI 1. The iScan Duo automatically outputs the preferred output format of your display. Once
connected, press the MENU button and you should see the iScan Duo’s OSD.
V
">
