Pressmaster CX 202 Operating instructions

PDF

Document

Figure 1 shows what strip lengths any given Kit/Cassette will give.

Refer to instruction material for your connector to detennine your strip requirements. Then refer to Fig. I to find which cassette you should use.

Cassette V-block

(Four V-blocks included in each kit. See Fig. 10 for size and colour.)

2-step cassette(2 blades)

2-step strip

Corex II Kit

Cassette

Colour

Blade Spacing

(B) “/mm

CX 202

C 202 red

0.24 (6,0)

CX 207

C 207 blue

0.27 (6,8)

CX 203

C 203 orange

0.36 (9,2)

CX 202

C 202 yellow

0.47 (12,0)

3-step cassette(3 blades)

3-step strip

Corex II Kit

Cassette

CX 309

C 309 white Colour

Blade Spacing

(B) “/mm

0.266 (6,8)

0.10 (2,5)

CX 301

C 301 brown

CX 300

C 300 black

CX 305

C 305 green

CX 305

C 305 green

0.328 (8,3)

0.109 (2,7)

0.220 (5,5)

Figure 1

0.235 (6,0)

*(A) can be adjusted with C-ST, conductor stop.

Note the parts of the stripper in Figure 2.

Numbers 1 to 2 imprinted inside cassette

Cassette

Locking latch

Slide

V-Block

G. Moves lide back one position. Then

pull cable out carefully while squeezing

tool (Fig. 8). If there is too much resistance

or strip is imperfect, go to step

"H".

Adjusting the Corex® II Coaxial Cable Stripper

H. Inspect your first strip. Determine

how deeply each blade has scored the

cable.

I. Adjust blade depth to match your

cable size by turning allen screws at

base of tool (Fig. 9).

Tips: If a blade is near its proper position, turn its set screw app. ± 90°.

If blade is a little far off from its proper position, turn its screw

± 270° - ± 360°.

Note: adjust tool so that the appropriate slide progression works

(Figure 6), develop your own 2- or 3-stage sliding sequence.

2 mm allen

wrench

J. Try stripping again, following steps A through G. If strip is still not acceptable, adjustbladesone more time, followinginstructions

H and I.

Solutions to typical problems

If braid is twisting too much, turn set screw for braid-cutting blade

+90° and turn set screw for jacket-cutting blace -90°.

If, after repeated adjustment, most of braid will not cut properly, your blade set is probably worn out. Reverse cassette to try new blade set.

With RG 174 or other very thin cable, very fine adjustment is needed. Expect to make several adjustments (±30°), to reach proper blade depth. Use a fresh blade set. Use only high quality thin cable.

Follow these steps when stripping with the Corex ®

Stripper.

II Coaxial

A. Adjust slide to pas. 4 or 5.

B. Open tool by rotating locking latch

downwards (Fig. 3).

C. Mark jacket of cable for center conductor

length. (If you have a simple wire

cutter, ignore this instruction. You car.

cut center conductor to length after the

strip or use conductor stop C-ST.)

D. Hold the tool with the handle towards

you and insert coax from left into the

groove position. Close and latch tool.

(Figs. 4 and 5)

E. Push slide forward to apprcpriate start

position (see Fig. 6). Make sure proper

V-block is installed.

Recommended Settings

Coax

RG 58

RG 59, 62

RG 174, 188, 316

RG 6

Belden8281

RG 195, 180

V-block

Blue

White

Yellow

Red

Figure 6

F. Rotate tool around coax about 5 times

(Fig. 7). Push slide forward to next

position in sequence. Rotate tool again.

Then push slide forward to final position

and rotate tool final 5 times.

Slide Progression

3, 2, 1

5, 4, 3

4, 3

5, 4, 3

5, 4

4, 3, 2

Mark on cable positioned over blade

V-block

Select proper V-block by O.D. of wire (see Fig. 10).

V-block

V-9

V-2

V-7

V-4

Cable Ø

2,5 - 3 mm

3,0 - 5 mm

5,0 - 6,4 mm

6,4 - 7,6 mm

Figure 10

To change V-block. Open tool fully (Fig.

11) until the springs holding V-block release. Pull out V-block and replace with selected V-block. Note! With white V-block, you must position springs in holes.

Colour

White

Red

Blue

Yellow

Cassettes

Each cassette contains 2 sets of cutting edges. Cassette can be reversed each time a blade set wears out. Numbers 1 and 2 are printed inside cassette to deterrnine usage.

To change or reverse cassette.

Move locking latch in direction of arrow, then push cassette out of tool by inserting wrench through hole in bottom of tool

(Fig. 12).

3-step strip with 2-bladed cassette

This procedure is recommended only in those cases where the 3-step strip you require is not available in one of the standard Corex

Series cassettes.

® II

A. If your required strip length is as

shown in Figure 13. you will choose

the 2-step cassette that matches your

"C"-dimension. Mark cable at length

A+C from end (Fig. 14).

B. Open tool, insert coax from left, and

locate mark on cable over the right-

handed blade.

C. Close and latch tool and strip cable

according to prior instruction.

Note: An adjustment of the tool might be necessary. A correct strip is shown in Fig.

15.

D. Mark exposed dielectric at length "A" from end.

E. Remove dielectric at the mark with a simple wire stripping plier (Fig. 16).

Mark exposed dielectric here

The slide is the most unique and important part of the stripper. The slide allows you to ease the blades into the cable, reducing friction on the braid and dielectric as you strip.

Always use your slide when you strip!

Recommended Settings

Coax

RG 58

RG 59, 62

RG 174, 188, 316

RG 6

Belden8281

RG 195, 180

V-block

Blue

White

Yellow

Red

Slide Progression

3, 2, 1

5, 4, 3

4, 3

5, 4, 3

5, 4

4, 3, 2

Adjust your tool so that the appropriate slide progression works. If your cable size does not appear in this table, develop your own 2- or

3-stage sliding sequence.

Note: Always step back 1 position on slide before pulling cable out

of tool.

Warning! 3-step is not recommended for most styles of RG 62, not for many cable styles with cellular polyethylene or other soft dielectrics. Use 2-step tool instead.

Do not use stripper on coax cables with drain wires.

Corex

II

COAXIAL WIRE STRIPPER

Adjustment Gauge Corex ® II "REDDY"

A. Open the tool by rotating locking

latch downwards (Fig. 17).

B. Remove the cassette from the tool by

moving the locking latch in the direction

of the arrow (Fig 18). Then push

the cassette out of the tool by inserting

wrench, or appropriate object, through

hole in bottom of the tool. Turn blade

adjustment set screws counterclockwise

until they are fully retracted.

C. Installation of adjustment gauge.

The gauge is marked with different

cable types. Install gauge so that the

markings, which correspond to the

cable type to be stripped are above the

adjustment screws (Fig. 19). Close the

tool.

D. Adjustment of the adjustment screws.

Rotate adjustment screws clockwise

until they touch the gauge (Fig. 20).

Then open the tool and remove the

gauge. Install the cassette, and the tool

is now ready for use.

2 mm allen

wrench

4100-4118-2

OPERATING INSTRUCTION

Hello! I am an AI chatbot specifically trained to assist you with the Pressmaster CX 202 Operating instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you're looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

It looks like you'''ve reached a document that is written in multiple languages, including one that isn''t your native language. You can use the following links to temporarily hide pages without the language you prefer.