Inventek Systems
eS-WiFi
ISM43362-M3G-EVB
Quick Start Guide
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
Installing the Inventek Systems ISM43362-M3G-EVB Evaluation Board
1.
BEFORE you plug the board into your computer download and
install the eS-WiFi PC demo software and Drivers:
http://www.inventeksys.com/wpcontent/uploads/Inventek_Systems_eSWiFiDemo_v1.4_b2.zip
2.
3.
4.
Save the eS-Wifi Demo.zip.
Unzip.
Run as Administrator.
a. The board has two com ports.
USB-JTAG and Broadcom USB serial port
b. Use the Broadcom USB serial port as indicated by the
arrow in the above photo of the EVB.
The ISM43362-M3G-EVB connects to the PC with a USB cable. The USB
interface provides +5V power as well as individual programming and
UART interfaces to the STM32F205 host processor (on the ISM43362M3G-L44 module).
The USB driver for the ISM43362-M3G-EVB Evaluation Board is provided
in the above download. Once you install the above software you can
select Menu>Install Drivers on the eS-WiFi Demo to pre-install the
drivers then plug-in the board.
Open the following documents to start testing:
a. EVB_Users_Manual.pdf
b. AT Command Set Quick Reference Guide
c. AT Command Set User’s Manual
We recommend that you use the eS-WiFi Demo Software Help, that will
explain the driver installation. (Manual installation instructions are also
shown in the appendix of this document.)
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
5. Use the eS-WiFi demo software setup menu to configure the
UART. (Setup – Serial Port – Configure/Open)
a. Identify serial Com port from Device Manager , e.g.
COM22
b. Set Baud rate to 115,200
c. 8 Data bits, 1 Stop bit , Parity None, and Flow control
None
(The other option is to use a terminal program such as Hyperterminal, PuTTY (http://putty.org) or similar program on your PC.)
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
6. Press the reset button on the ISM43362-M3G-EVB evaluation
board and the following will appear:
7. The AT Command interpreter is loaded on the ISM43362-M3GEVB.
Type ? to view the available commands.
8. For additional information refer to the following documentation
from Inventek Systems:
ISM43362-M3G-EVB Evaluation Board Specification
AT Command set
eS-WiFi Demo software (includes EVB Drivers)
EVB Users Guide
Quick Start Guide
OrCAD Schematic Symbol
PADS Land Pattern
ISM43362-M3G-L44 Functional Specification
FCC Test Report
NDA/ SLA documents
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
Appendix: Manual Installation Instructions:
NOTE: Driver installation occurs in THREE stages, each stage is described
in the following text.
Plug the ISM43362-M3G-EVB into the development PC. The Found New
Hardware Wizard window appears.
Now perform the follow actions:
Select the checkbox : No, not this time
Click Next.
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
In the next window, perform the following actions.
Verify that the driver installation is for BCM9WCD1EVAL1
Select the checkbox : Install from a list or specified location
(Advanced).
Click Next
C:\Program Files\....\eS-Wifi\drivers
In the next window, perform the following actions.
Check the radio button : Search for the best driver in these
locations
Click the checkbox : Include this location in the search:
Enter the path to the directory : C:\Program Files\Inventek
Systems\eS-WiFi\drivers
Click Next
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
A further window displays indicating that the driver has been installed
for the BCM9WCD1EVAL1 A device (corresponding to the USB-JTAG
device). There are two devices on the BCM9WCD1EVAL1 board, a USBJTAG device (device A) and a USB-UART device (device B).
Click Finish
After a short delay, another Found New Hardware Wizard window
opens. Install the driver for the BCM9WCD1EVAL1 B device using the
same procedure as the BCM9WCD1EVAL1 A device. If a Windows Logo
Testing window appears, click Continue anyway.
Once the BCM9WCD1EVAL1 B device driver is installed, a serial port
driver must be installed. The serial port driver makes the USB-Serial
interface appear to Windows® as a standard COM port. Follow the same
procedure outlined for the BCM9WCD1EVAL1 A and B devices to install
the serial port driver. Again, if a Windows Logo Testing window appears,
click Continue anyway.
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
After the driver is successfully installed, a Broadcom USB-JTAG Device
and a Broadcom USB Serial Port appear in the Windows® Device
Manager as shown in the following screen capture. Take note of the
USB serial COM port number for later use (it may not be COM3).
Note: The Hardware Device Manager may be accessed quickly from the
System Properties window by simultaneously pressing the Windows +
Pause keys.
Inventek Systems eS-WiFi ISM43362-M3G-EVB Quick Start Guide – Rev. 2
Inventek Systems
2 Republic Road
Billerica, MA 01862
www.inventeksys.com
">
