LM2902W
Low-power quad operational amplifier
Datasheet - production data
Features
Wide gain bandwidth: 1.3 MHz
Input common-mode voltage range includes negative rail
Large voltage gain: 100 dB
Very low supply current per amplifier:
375 µA
Low input bias current: 20 nA
Low input offset current: 2 nA
ESD internal protection: 800 V
Wide power supply range
Single supply: 3 V to 30 V
Dual supplies: ±1.5 V to ±15 V
Description
This circuit consists of four independent, highgain operational amplifiers which have frequency compensation implemented internally and are designed especially for automotive and industrial control systems.
The device operates from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.
All the pins are protected against electrostatic discharges up to 800 V.
February 2016 DocID9922 Rev 10
This is information on a product in full production.
1/19
www.st.com
Contents LM2902W
Contents
1 Schematic diagram .......................................................................... 3
2 Package pin connections ................................................................ 4
3 Absolute maximum ratings and operating conditions ................. 5
4 Electrical characteristics ................................................................ 6
5 Electrical characteristic curves ...................................................... 8
6 Typical single-supply applications .............................................. 11
7 Macromodel ................................................................................... 13
8 Package information ..................................................................... 14
8.1
8.2
SO14 package information .............................................................. 15
TSSOP14 package information ....................................................... 16
9 Ordering information ..................................................................... 17
10 Revision history ............................................................................ 18
2/19 DocID9922 Rev 10
LM2902W
1 Schematic diagram
Figure 1: Schematic diagram (1/4 LM2902W)
Schematic diagram
DocID9922 Rev 10 3/19
Package pin connections
2 Package pin connections
Figure 2: SO14 and TSSOP14 pin connections (top view)
LM2902W
4/19 DocID9922 Rev 10
LM2902W
3
Absolute maximum ratings and operating conditions
Absolute maximum ratings and operating conditions
Symbol
Table 1: Absolute maximum ratings
Parameter Value Unit
V
CC
V id
V i
Supply voltage
Differential input voltage
Input voltage
Output short-circuit to ground
(1)
Input current
(2)
±16 to 32
32
-0.3 to (V
CC
+
) + 0.3
Infinite
V
I in
T stg
Storage temperature range
50
-65 to 150
105 mA
°C
R thja
Thermal resistance junction to ambient
(3)
SO14
TSSOP14
SO14
100
31
°C/W
R thjc
Thermal resistance junction to case
(3)
TSSOP14
32
ESD
HBM: human body model
(4)
MM: machine model
(5)
CDM: charged device model
(6)
800
100
1500
V
Notes:
(1)
Short-circuits from the output to V
CC
+ can cause excessive heating and potential destruction. The maximum output current is approximately 20 mA, independent of the magnitude of V
CC
+
(2)
This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward biased and thereby acting as an input diode clamp. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V
CC
voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. This is not destructive and normal output is restored for input voltages higher than -0.3 V.
(3)
R thja/c
are typical values.
(4)
Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
(5)
Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected pin combinations while the other pins are floating.
(6)
Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins.
Symbol
Table 2: Operating conditions
Parameter Value Unit
V
CC
V icm
T oper
Supply voltage
Common mode input voltage range
Operating free-air temperature range
3 to 30
(V
CC
-
) to (V
CC
+
) - 1.5
T min
≤ T amb
≤ T max
(V
CC
-
) to (V
CC
+
) - 2
-40 to 125
V
°C
DocID9922 Rev 10 5/19
Electrical characteristics
LM2902W
4
Symbol
V i o
ΔV io
/ΔT
I io
DI io
I ib
A vd
SVR
I
CC
CMR
I o
I sink
V
OH
V
OL
SR
Electrical characteristics
Table 3: VCC+ = 5 V, VCC- = ground, VO = 1.4 V, Tamb = 25 °C (unless otherwise stated)
Parameter Test conditions Min. Typ. Max. Unit
Input offset voltage
(1)
Input offset voltage drift
Input offset current
LM2902W
LM2902AW
T min
≤ T amb
≤ T max
, LM2902W
T min
≤ T amb
≤ T max
, LM2902AW
T amb
= 25 °C
T min
≤ T amb
≤ T max
2
7
2
7
2
9
4
30
40 mV
30 µV/°C nA
Input offset current drift
Input bias current
(2)
Large signal voltage gain
Supply voltage rejection ratio
Supply current
(all op amps, no load)
Common-mode rejection ratio
Output short-circuit current
T amb
= 25 °C
T min
≤ T amb
≤ T max
V
CC
+
= 15 V, R
L
=
2 kΩ, V
ο
= 1.4 V to 11.4 V,
T amb
= 25 °C
V
CC
+
= 15 V, R
L
=
2 kΩ, V
ο
= 1.4 V to 11.4 V,
T min
≤ T amb
≤ T max
R
S
≤ 10 kΩ, T amb
= 25 °C
R
S
≤ 10 kΩ, T min
≤ T amb
≤ T max
T amb
= 25 °C, V
CC
+
= 5 V
T amb
= 25 °C, V
CC
+
= 30 V
T min
≤ T amb
≤ T max
, V
CC
+
= 5 V
T min
≤ T amb
≤ T max,
V
CC
+
= 30 V
R
S
≤ 10 kΩ, T amb
= 25 °C
R
S
≤ 10 kΩ, T min
≤ T amb
≤ T max
V id
= 1 V, V
CC
+
= 15 V, V o
= 2 V
10
20
50 100
70
60
25
65 110
65
0.7
1.5
0.9
20
1.5
80
40
200 pA/°C
150
300
1.2
3
1.2
3
70 nA
V/mV dB mA dB mA
Output sink current
High-level output voltage
Low level output voltage
Slew rate
V id
= -1 V, V
CC
+
= 15 V, V o
= 2 V
V id
= -1 V, V
CC
+
= 15 V, V o
= 0.2 V
V
CC
+
= 30 V, R
L
= 2 kΩ, T amb
= 25 °C
V
CC
+
= 30 V, R
L
= 2 kΩ, T min
= T amb
= T max
V
CC
+
= 30 V, R
L
= 10 kΩ, T amb
= 25 °C
V
CC
+
= 30 V, R
L
= 10 kΩ, T min
= T amb
= T max
V
CC
+
= 5 V, R
L
= 2 kΩ, T amb
= 25 °C
V
CC
+
= 5 V, R
L
= 2 kΩ, T min
= T amb
= T max
R
L
= 10 kΩ, T amb
= 25 °C
R
L
= 10 kΩ, T min
= T amb
= T max
V
CC
+
= 15 V, V in
= 0.5 to 3 V, R
L
=
2 kΩ,
C
L
= 100 pF, unity gain
10 20
12
26
26
27
27
50
27
28
3.5
3
0.24 0.4
5 20
20
µA
V mV
V/µs
6/19 DocID9922 Rev 10
LM2902W
Symbol
SR
Parameter
Slew rate
GBP
THD e n
V
O1
/V
O
2
Gain bandwidth product
Total harmonic distortion
Equivalent input noise voltage
Channel
separation
(3)
Test conditions
V
CC
+
= 15 V, V in
= 0.5 to 3 V, R
L
=
2 kΩ,
C
L
= 100 pF, unity gain, T min
≤ T amb
≤ T max
V
CC
+
= 30 V, V in
= 10 mV, R
L
=
2 kΩ,
C
L
= 100 pF f = 1 kHz, A
V
= 20 dB, R
L
=
2 kΩ, V o
= 2 V pp
,
C
L
= 100 pF, V
CC
+
= 30 V f = 1 kHz, R
S
=
100 Ω, V
CC
+
= 30 V
1 kHz ≤ f ≤ 20 kHz
Electrical characteristics
Min. Typ. Max. Unit
0.14
1.3
0.015
40
120
V/µs
MHz
% nV/√Hz dB
Notes:
(1)
V
O
= 1.4 V, R
S
= 0
Ω, 5 V < V
CC
+
< 30 V, 0 V < V ic
< (V
CC
+
) - 1.5 V.
(2)
The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output, so there is no change in the load on the input lines.
(3)
Due to the proximity of external components, ensure that stray capacitance does not cause coupling between these external parts. Typically, this can be detected as this type of capacitance increases at higher frequencies.
DocID9922 Rev 10 7/19
Electrical characteristic curves
5 Electrical characteristic curves
Figure 3: Input bias current vs. Tamb
Figure 4: Input voltage range
LM2902W
Figure 5: Current limiting Figure 6: Supply current
Figure 7: Gain bandwidth product Figure 8: Voltage follower pulse response (VCC = 15 V)
8/19 DocID9922 Rev 10
LM2902W
Figure 9: Common-mode rejection ratio
Electrical characteristic curves
Figure 10: Output characteristics (sink)
Figure 11: Open-loop frequency response Figure 12: Voltage follower pulse response
(VCC = 30 V)
Figure 13: Large signal frequency response Figure 14: Output characteristics (source)
DocID9922 Rev 10 9/19
Electrical characteristic curves
Figure 15: Input current Figure 16: Voltage gain
LM2902W
Figure 17: Power supply and common-mode rejection ratio
Figure 18: Large signal voltage gain
10/19 DocID9922 Rev 10
LM2902W
Typical single-supply applications
6 Typical single-supply applications
Figure 19: AC coupled inverting amplifier
Figure 20: AC coupled non-inverting amplifier
Figure 21: Non-inverting DC gain Figure 22: DC summing amplifier
Figure 23: Active bandpass filter Figure 24: High input Z adjustable gain DC instrumentation amplifier
DocID9922 Rev 10 11/19
Typical single-supply applications
Figure 25: High input Z, DC differential amplifier
LM2902W
Figure 26: Low drift peak detector
Figure 27: Using symmetrical amplifiers to reduce input current (general concept)
12/19 DocID9922 Rev 10
LM2902W
7
Macromodel
Macromodel
An accurate macromodel of the LM2902W is available on STMicroelectronics’ web site at
www.st.com. This model is a trade-off between accuracy and complexity (that is, time simulation) of the LM2902W operational amplifiers. It emulates the nominal performances of a typical device within the specified operating conditions mentioned in the datasheet. It also helps to validate a design approach and to select the right operational amplifier, but it
does not replace on-board measurements.
DocID9922 Rev 10 13/19
Package information
8 Package information
LM2902W
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK
® specifications, grade definitions and product status are available at: www.st.com.
ECOPACK
®
is an ST trademark.
14/19 DocID9922 Rev 10
LM2902W
8.1 SO14 package information
Figure 28: SO14 package outline
Package information
Ref.
D
E e
H h
L
A
A1
A2
B
C k ddd
Min.
1.35
0.10
1.10
0.33
0.19
8.55
3.80
5.80
0.25
0.40
Table 4: SO14 mechanical data
Dimensions
Millimeters
Typ. Max. Min.
1.75
0.25
1.65
0.51
0.25
8.75
4.0
0.05
0.004
0.04
0.01
0.007
0.33
0.15
1.27
6.20
0.50
1.27
0.009
0.015
8° (max)
0.22
0.10
DocID9922 Rev 10
Inches
Typ.
0.05
Max.
0.068
0.009
0.06
0.02
0.009
0.34
0.15
0.24
0.02
0.05
0.004
15/19
Package information
8.2 TSSOP14 package information
Figure 29: TSSOP14 package outline
LM2902W
aaa
16/19
Ref.
E
E1 e
L
L1 k aaa
A
A1
A2 b c
D
Min.
0.05
0.80
0.19
0.09
4.90
6.20
4.30
0.45
0°
5.00
6.40
4.40
0.65
0.60
1.00
Table 5: TSSOP14 mechanical data
Dimensions
Millimeters
Typ. Min.
1.00
Max.
1.20
0.15
1.05
0.30
0.20
5.10
6.60
4.50
0.002
0.031
0.007
0.004
0.193
0.244
0.169
0.75 0.018
8°
0.10
0°
Inches
Typ.
0.004
0.039
0.197
0.252
0.173
0.0256
0.024
0.039
DocID9922 Rev 10
Max.
0.047
0.006
0.041
0.012
0.0089
0.201
0.260
0.176
0.030
8°
0.004
LM2902W
9
Ordering information
Ordering information
Order code
Table 6: Order codes
Temperature range Package
LM2902WDT
LM2902WYDT
(1)
LM2902AWYDT
(1)
LM2902WPT
LM2902WYPT
(1)
LM2902AWYPT
(1)
-40 °C to 125 °C
SO14
SO14
(automotive grade level)
TSSOP14
TSSOP14
(automotive grade level)
Packing
Tape and reel
Marking
2902W
2902WY
2902AWY
2902W
2902WY
2902AWY
Notes:
(1)
Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent.
DocID9922 Rev 10 17/19
Revision history
10
LM2902W
Revision history
Date Revision
Table 7: Document revision history
Changes
01-Sep-2003
01-Nov-2005
01-Jan-2006
01-May-2006
20-Jul-2007
15-Jan-2008
17-Oct-2008
16-Feb-2012
22-Jul-2013
19-Feb-2016
1
2
3
4
5
6
7
8
9
10
Initial release.
Table data reformatted for easier use in Electrical characteristics on page 4.
Minor grammatical and formatting changes throughout.
LM2902WYPT PPAP reference inserted in order codes table, see
Section 7 on page 16.
Minimum value of slew rate at 25°C and on full temperature range added in Table 3 on page 5.
Corrected document title to “quad operational amplifier”.
Corrected ESD value for HBM to 800V.
Corrected thermal resistance junction to ambient values in Table 1:
Absolute maximum ratings.
Updated electrical characteristics curves.
Added Section 5: Macromodel.
Added automotive grade order codes in Section 7 on page 16.
Corrected footnotes for automotive grade order codes.
Added enhanced Vio version: LM2902AW.
Corrected V
OH
min parameter at V cc
=5V in Table 3 on page 5.
Modified Chapter 5: Macromodel.
Deleted LM2902WYD and LM2902AWYD order codes from Table 7 and modified status of LM2902WYPT and LM2902AWYPT order codes.
Table 3: DV io replaced with ΔV io
/ΔT
Table 7: Removed the order codes LM2902WN and LM2902WD; replaced the order codes LM2902WDT and LM2902AWDT with
LM2902WYDT and LM2902AWYDT respectively.
Updated layout
Removed DIP14 package and all information pertaining to it
Removed “D, plastic micropackage” and “P, thin shrink small outline package” respectively from the SO14 and TSSOP14 silhouettes.
Section 8.1: "SO14 package information"
: replaced SO14 package
outline and mechanical data
Section 8.2: "TSSOP14 package information"
: updated E1 max mm
value, L1 value, and added "aaa" information.
Table 6: "Order codes"
: added order code LM2902WDT
18/19 DocID9922 Rev 10
LM2902W
IMPORTANT NOTICE
– PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics
– All rights reserved
DocID9922 Rev 10 19/19
