Nikon COOLPIX AW120 Specification
Pubblicità
Pubblicità
DIGITAL CAMERA
Reference Manual
Waterproofing
The following are important notes about the camera's waterproofing. Before
using the camera, please thoroughly read the information in “<Important>
Shockproof, Waterproof, Dustproof, Condensation” ( Axii).
Waterproofing-related Messages
The camera will display messages related to its waterproof capabilities when you select certain settings or perform certain operations. Read and follow the information displayed in the messages when they are displayed.
Do not open the covers by the water or in sandy locations, as foreign matter could enter the camera.
Remove any foreign matter with a brush or blower.
1/6
Confirm that no foreign matter is present where shown, then close the covers.
3/6
Next, wipe off any water droplets and place on a cloth to dry.
2/6
To remove foreign matter after use, immerse in fresh water for about 10 minutes.
4/6
After drying thoroughly, use a cloth to remove any droplets remaining on the areas indicated.
5/6 6/6 Exit
Waterproofing-related messages are displayed in the following situations.
• When turning on and setting the camera for the first time
• When setting the camera to Underwater (A41)
• When turning the camera on after charging
Warning: If the cover is closed without removing foreign particles, water may seep inside the camera or the camera may become damaged.
Make sure to check and clean the camera.
Introduction
Parts of the Camera
The Basics of Shooting and Playback
Shooting Features
Playback Features
Recording and Playing Back Movies
General Camera Setup
Using Location Data Functions/Displaying Maps
Using the Wi-Fi (Wireless LAN) Function
Connecting the Camera to a TV, Computer, or Printer
Reference Section
Technical Notes and Index
i
ii
Introduction
Read This First
Thank you for purchasing the Nikon COOLPIX AW120 digital camera. Before
using the camera, please read the information in “For Your Safety” (
"<Important> Shockproof, Waterproof, Dustproof, Condensation" ( Axii),
"<Important> Notes About Location Data Functions (GPS/GLONASS, Electronic
Axviii), and "Wi-Fi (Wireless LAN Network)" (Axx), and familiarize
yourself with the information provided in this manual. After reading, please keep this manual handy and refer to it to enhance your enjoyment of your new camera.
About This Manual
If you want to start using the camera right away, see “The Basics of Shooting and Playback” ( A12).
To learn about the parts of the camera and information that is displayed in the
monitor, see “Parts of the Camera” ( A1).
Other Information
• Symbols and Conventions
To make it easier to find the information you need, the following symbols and conventions are used in this manual:
B
C
Symbol Description
This icon indicates cautions and information that should be read before using the camera.
This icon indicates notes and information that should be read before using the camera.
A/E/F
These icons indicate other pages containing relevant information;
E: “Reference Section”, F: “Technical Notes and Index.”
• SD and SDHC/SDXC memory cards are referred to as “memory cards” in this manual.
• The setting at the time of purchase is referred to as the “default setting.”
• The names of menu items displayed in the camera monitor, and the names of buttons or messages displayed on a computer monitor appear in bold.
• In this manual, images are sometimes omitted from monitor display samples so that monitor indicators can be more clearly shown.
• Illustrations and monitor content shown in this manual may differ from the actual product.
iii
iv
Information and Precautions
Life-Long Learning
As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education, continually updated information is available online at the following sites:
• For users in the U.S.A.: http://www.nikonusa.com/
• For users in Europe and Africa: http://www.europe-nikon.com/support/
• For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently asked questions (FAQs), and general advice on digital imaging and photography. Additional information may be available from the Nikon representative in your area. Visit the site below for contact information: http://imaging.nikon.com/
Use Only Nikon Brand Electronic Accessories
Nikon COOLPIX cameras are designed to the highest standards and include complex electronic circuitry. Only Nikon brand electronic accessories (including battery chargers, batteries, charging AC adapters, AC adapters, and cables) certified by Nikon specifically for use with this Nikon digital camera are engineered and proven to operate within the operational and safety requirements of this electronic circuitry.
T
HE USE OF NON-
N
IKON ELECTRONIC ACCESSORIES COULD DAMAGE THE CAMERA
AND MAY VOID YOUR
N
IKON WARRANTY.
The use of third-party rechargeable Li-ion batteries not bearing the Nikon holographic seal could interfere with normal operation of the camera or result in the batteries overheating, igniting, rupturing, or leaking.
For more information about Nikon brand accessories, contact a local authorized
Nikon dealer.
Holographic seal: Identifies this device as an authentic Nikon product.
Before Taking Important Pictures
Before taking pictures on important occasions (such as at weddings or before taking the camera on a trip), take a test shot to ensure that the camera is functioning normally. Nikon will not be held liable for damages or lost profits that may result from product malfunction.
About the Manuals
• No part of the manuals included with this product may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without Nikon’s prior written permission.
• Nikon reserves the right to change the specifications of the hardware and software described in these manuals at any time and without prior notice.
• Nikon will not be held liable for any damages resulting from the use of this product.
• While every effort was made to ensure that the information in these manuals is accurate and complete, we would appreciate it were you to bring any errors or omissions to the attention of the Nikon representative in your area (address provided separately).
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that was digitally copied or reproduced by means of a scanner, digital camera or other device may be punishable by law.
• Items prohibited by law from being copied or reproduced
Do not copy or reproduce paper money, coins, securities, government bonds or local government bonds, even if such copies or reproductions are stamped “Sample.” The copying or reproduction of paper money, coins, or securities which are circulated in a foreign country is prohibited. Unless the prior permission of the government was obtained, the copying or reproduction of unused postage stamps or post cards issued by the government is prohibited.
The copying or reproduction of stamps issued by the government and of certified documents stipulated by law is prohibited.
• Cautions on certain copies and reproductions
The government has issued cautions on copies or reproductions of securities issued by private companies (shares, bills, checks, gift certificates, etc.), commuter passes, or coupon tickets, except when a minimum of necessary copies are to be provided for business use by a company. Also, do not copy or reproduce passports issued by the government, licenses issued by public agencies and private groups, ID cards and tickets, such as passes and meal coupons.
• Comply with copyright notices
The copying or reproduction of copyrighted creative works such as books, music, paintings, woodcut prints, maps, drawings, movies, and photographs is governed by national and international copyright laws. Do not use this product for the purpose of making illegal copies or to infringe copyright laws.
v
vi
Disposing of Data Storage Devices
Please note that deleting images or formatting data storage devices such as memory cards or built-in camera memory does not completely erase the original image data.
Deleted files can sometimes be recovered from discarded storage devices using commercially available software, potentially resulting in the malicious use of personal image data. Ensuring the privacy of such data is the user’s responsibility.
Before discarding a data storage device or transferring ownership to another person, erase all data using commercial deletion software, or set Record location data of
Location data options (
A87) to Off after formatting the device and then
completely refill it with images containing no private information (for example, pictures of empty sky). Be sure to also replace any pictures selected for the Select an
image option in the Welcome screen setting (
avoid injury or damage to property when physically destroying data storage devices.
For the COOLPIX AW120, the log data saved on the memory card is handled in the same way as other data. To erase the log data that is obtained but not stored on the memory card, select Create log ➝ End all logs ➝ Erase logs.
You can clear the Wi-Fi setting using Restore default settings in the Wi-Fi options
(
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others, read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use the product will read them.
The consequences that could result from failure to observe the precautions listed in this section are indicated by the following symbol:
This icon marks warnings, information that should be read before using this Nikon product, to prevent possible injury.
WARNINGS
Turn off in the event of malfunction
Should you notice smoke or an unusual smell coming from the camera or charging AC adapter, unplug the charging AC adapter and remove the battery immediately, taking care to avoid burns.
Continued operation could result in injury. After removing or disconnecting the power source, take the equipment to a Nikonauthorized service representative for inspection.
Do not disassemble
Touching the internal parts of the camera or charging AC adapter could result in injury. Repairs should be performed only by qualified technicians. Should the camera or charging AC adapter break open as the result of a fall or other accident, take the product to a Nikonauthorized service representative for inspection, after unplugging the product and/or removing the battery.
Do not use the camera or charging AC adapter in the presence of flammable gas
Do not use electronic equipment in the presence of flammable gas, as this could result in explosion or fire.
Remove the strap when using the camera underwater
Twisting the camera strap around the neck may cause suffocation.
Handle the camera strap with care
Never place the strap around the neck of an infant or child.
Keep out of reach of children
Particular care should be taken to prevent infants from putting the battery or other small parts into their mouths.
vii
viii
Do not remain in contact with the camera, charging
AC adapter, or AC adapter for extended periods while the devices are on or in use
Parts of the devices become hot.
Leaving the devices in direct contact with the skin for extended periods may result in low-temperature burns.
Do not leave the product where it will be exposed to extremely high temperatures, such as in an enclosed automobile or in direct sunlight
Failure to observe this precaution could cause damage or fire.
Use the appropriate power supply (battery, charging
AC adapter, AC adapter,
USB cable)
Using a power supply other than those provided or sold by Nikon could result in damage or malfunction.
Observe caution when handling the battery
The battery may leak, overheat, or explode if improperly handled.
Observe the following precautions when handling the battery for use in this product:
• Before replacing the battery, turn the product off. If you are using the charging AC adapter/AC adapter, be sure it is unplugged.
• Use only a Rechargeable Li-ion
Battery EN-EL12 (included).
Charge the battery by using a camera that supports battery charging. To perform this operation, use the Charging AC
Adapter EH-71P (included) and
USB Cable UC-E21 (included). The
Battery Charger MH-65 (available separately) is also available to charge the battery without using a camera.
• When inserting the battery, do not attempt to insert it upside down or backwards.
• Do not short or disassemble the battery or attempt to remove or break the battery insulation or casing.
• Do not expose the battery to flame or to excessive heat.
• Do not immerse in or expose to water.
• Put the battery in a plastic bag, etc. to insulate the terminal before transporting it. Do not transport or store with metal objects such as necklaces or hairpins.
• The battery is prone to leakage when fully discharged. To avoid damage to the product, be sure to remove the battery when no charge remains.
• Discontinue use immediately should you notice any change in the battery, such as discoloration or deformation.
• If liquid from the damaged battery comes in contact with clothing or skin, rinse immediately with plenty of water.
Observe the following precautions when handling the charging AC adapter
• Keep dry. Failure to observe this precaution could result in fire or electric shock.
• Dust on or near the metal parts of the plug should be removed with a dry cloth. Continued use could result in fire.
• Do not handle the plug or go near the charging AC adapter during lightning storms. Failure to observe this precaution could result in electric shock.
• Do not damage, modify, forcibly tug or bend the USB cable, place it under heavy objects, or expose it to heat or flames. Should the insulation be damaged and the wires become exposed, take it to a Nikon-authorized service representative for inspection.
Failure to observe these precautions could result in fire or electric shock.
• Do not handle the plug or charging AC adapter with wet hands. Failure to observe this precaution could result in electric shock.
• Do not use with travel converters or adapters designed to convert from one voltage to another or with DC-to-AC inverters. Failure to observe this precaution could damage the product or cause overheating or fire.
Use appropriate cables
When connecting cables to the input and output jacks, use only the cables provided or sold by Nikon for the purpose, to maintain compliance with product regulations.
Handle moving parts with care
Be careful that your fingers or other objects are not pinched by the lens cover or other moving parts.
Using the flash close to your subject's eyes could cause temporary visual impairment
The flash should be no less than 1 m
(3 ft 4 in.) from the subject.
Particular care should be observed when photographing infants.
Do not operate the flash with the flash window touching a person or object
Failure to observe this precaution could result in burns or fire.
Turn the power off when using inside an airplane or the hospital
Turn the power off while inside the airplane during take off or landing.
Before boarding an airplane, set the record location data function to OFF.
End recording of all logs. Do not use wireless network functions while in the air. Follow the instructions of the hospital when using while in a hospital. The electromagnetic waves emitted by this camera may disrupt the electronic systems of the airplane or the instruments of the hospital. If you are using an Eye-Fi card, remove it from the camera before boarding an aircraft or entering a hospital.
Do not touch the camera directly for a long time in low temperatures of 0°C
(32°F) or lower
If the skin contacts metal parts etc., it may result in injury to the skin. Wear gloves etc.
Observe caution when using the movie light
Do not look directly into the movie light. This could damage the eyes or result in visual impairment.
ix
x
Notices
Notices for Customers in the U.S.A.
IMPORTANT SAFETY
INSTRUCTIONS -
SAVE THESE
INSTRUCTIONS.
DANGER - TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE
INSTRUCTIONS
For connection to a supply not in the
U.S.A., use an attachment plug adapter of the proper configuration for the power outlet if needed.
The power supply unit is intended to be correctly orientated in a vertical or floor mount position.
Federal Communications
Commission (FCC) Radio
Frequency Interference
Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
AW120
CAUTIONS
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Nikon Corporation may void the user’s authority to operate the equipment.
Interface Cables
Use the interface cables sold or provided by Nikon for your equipment. Using other interface cables may exceed the limits of Class
B Part 15 of the FCC Rules.
Notice for customers in the State of California
WARNING
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Wash hands after handling.
Nikon Inc.,
1300 Walt Whitman Road
Melville, New York 11747-3064
USA
Tel: 631-547-4200
Notice for customers in Canada
CAN ICES-3 B / NMB-3 B
Notices for customers in Europe
CAUTIONS
RISK OF EXPLOSION IF BATTERY
IS REPLACED BY AN INCORRECT
TYPE.
DISPOSE OF USED BATTERIES
ACCORDING TO THE
INSTRUCTIONS.
This symbol indicates that electrical and electronic equipment is to be collected separately.
The following apply only to users in European countries:
• This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste.
• Separate collection and recycling helps conserve natural resources and prevent negative consequences for human health and the environment that might result from incorrect disposal.
• For more information, contact the retailer or the local authorities in charge of waste management.
This symbol on the battery indicates that the battery is to be collected separately.
The following apply only to users in European countries:
• All batteries, whether marked with this symbol or not, are designated for separate collection at an appropriate collection point. Do not dispose of as household waste.
• For more information, contact the retailer or the local authorities in charge of waste management.
xi
xii
<Important> Shockproof, Waterproof,
Dustproof, Condensation
• Make sure to read the following instructions as well as the instructions
provided in “Caring for the Product” ( F2).
Notes About Shockproof Performance
This camera has passed Nikon’s in-house test (drop test from a height of 202 cm (6 ft 6 in.) on a 5 cm (2 in.) thick plywood panel) compliant with MIL-STD
810F Method 516.5-Shock*.
This test does not guarantee the waterproof performance of the camera or that the camera will be free from damage or trouble under all conditions.
Changes in appearance, such as paint peeling off and deformation of the drop shock portion are not subject to the Nikon’s in-house test.
* U.S. Department of Defense test method standard.
This drop test drops 5 cameras in 26 directions (8 edges, 12 corners, and 6 faces) from a height of 122 cm (48 in.) to make sure that one to five cameras pass the test
(if any defect is detected during the test, another five cameras are tested to make sure that the test criteria are satisfied for one to five cameras).
bDo not subject the camera to excessive shock, vibration or pressure by dropping or hitting it.
Failure to observe this precaution could cause water to seep inside the camera and result in camera malfunction.
• Do not use the camera deeper than 18 m (59 ft) underwater.
• Do not subject the camera to water pressure by exposing it to running water.
• Do not sit down with the camera in the pocket of your trousers.
Do not forcibly stuff the camera into a bag.
Notes About Waterproof and Dustproof
Performances
The camera is equivalent to JIS/IEC waterproof grade 8 (IPX8) and JIS/IEC dustproof grade 6 (IP6X) and enables shooting images underwater at a depth of 18 m (59 ft) for up to 60 minutes.*
This rating does not guarantee the waterproof performance of the camera or that the camera will be free from damage or trouble under all conditions.
* This rating indicates that the camera has been designed to withstand the specified water pressure for the specified period of time when the camera is used according to the methods defined by Nikon.
bIf the camera is subjected to excessive shock, vibration or pressure by dropping or hitting it, the waterproof performance is not guaranteed.
• If the camera is exposed to shocks, it is recommended to consult your retailer or Nikon-authorized service representative to confirm the waterproof performance (charged service).
- Do not use the camera deeper than 18 m (59 ft) underwater.
- Do not subject the camera to water pressure by exposing it to rapids or waterfalls.
- Your Nikon warrantee may not cover troubles caused by water seeping inside the camera due to improper handling of the camera.
• The waterproof performance of this camera is designed to work for fresh water (swimming pools, rivers and lakes) and seawater only.
• The inner portion of this camera is not waterproof. Water seeping inside the camera could cause a malfunction.
• Accessories are not waterproof.
• If a liquid such as water droplets falls on the outside of the camera or inside of the battery-chamber/ memory card slot cover, immediately wipe it off with a soft dry cloth. Do not insert a wet memory card or battery in the camera.
If the battery-chamber/memory card slot cover is opened or closed under wet conditions near a waterfront or underwater, this could cause water to seep inside the camera or result in camera malfunction.
Do not open or close the cover with wet hands. This could cause water to seep inside the camera or result in camera malfunction.
• If a foreign substance adheres to the outside of the camera or inside of the battery-chamber/memory card slot cover (in locations such as yellow waterproof packing, hinges, memory card slot, or terminals), immediately remove it with a blower. If a foreign substance adheres to the waterproof packing inside of the battery-chamber/memory card slot cover, remove it with the included brush. Do not use the included brush for anything other than cleaning the waterproof packing.
• If a foreign substance such as suntan oil, sunscreen lotion, hot spring, bath mix powder, detergent, soap, organic solvent, oil, or alcohol adheres to the camera, immediately wipe it off.
• Do not leave the camera in low temperature conditions in cold climate regions or in high-temperature conditions of 40°C (104°F) or more (in particular, a place exposed to direct sunlight, inside the cabin of a car, on a boat, on the beach, or near heating apparatus) for a long period of time. This could cause deterioration of the waterproof performance.
xiii
xiv
Before Using the Camera Underwater
Remove the strap for land use before using the camera underwater.
1. Make sure that there are no foreign substances inside the batterychamber/memory card slot cover.
• Any foreign substances such as sand, dust or hair inside the batterychamber/memory card slot cover should be removed with a blower.
• Any liquid such as water droplets inside the battery-chamber/memory card slot cover should be wiped off with a soft dry cloth.
2. Make sure that the waterproof packing ( A1) of the battery-
chamber/memory card slot cover is not cracked or deformed.
• The waterproof performance of waterproof packing may start to deteriorate after one year.
If the waterproof packing begins to deteriorate, consult your retailer or
Nikon-authorized service representative.
3. Make sure that the battery-chamber/memory card slot cover is firmly closed.
• Rotate the battery-chamber/memory card slot cover latch until it clicks into place. Make sure that the thin cord of the camera strap does not get caught.
• Make sure that the latch indicator indicates the “Close” status.
Notes About Using the Camera Underwater
Observe the following precautions to prevent water from seeping inside the camera.
• Do not dive into water deeper than 18 m (59 ft) with the camera.
• Do not continuously use the camera underwater for 60 minutes or more.
• Use the camera in the water temperature range from 0°C to 40°C (32°F to
104°F) when using it underwater.
• Do not use the camera at hot springs.
• Do not open or close the battery-chamber/memory card slot cover underwater.
• Do not subject the camera to shock when using it underwater.
Do not jump into water with the camera or subject it to high water pressure conditions such as rapids or waterfalls.
• This camera does not float in water. Make sure not to drop the camera underwater.
Cleaning after Using the Camera Underwater
• After using the camera underwater, clean the camera within 60 minutes. If you leave the camera in wet conditions where salt particles or other foreign substances are adhered to it, this could cause damage, discoloration, corrosion, a bad smell or deterioration of waterproof performance.
• Before cleaning the camera, thoroughly remove water droplets, sand, salt particles, or other foreign substances from your hands, body, and hair.
• It is recommended to clean the camera indoors to avoid a place where it could be exposed to water spray or sand.
• Do not open the battery-chamber/memory card slot cover until all foreign substances are washed off with water and all moisture is wiped off.
1. Keep the battery-chamber/memory card slot cover closed and wash off the camera with fresh water.
Immerse the camera in a shallow basin filled with fresh water (such as tap water and well-water that do not contain salt) for 10 minutes.
• If the buttons or switches do not operate properly, foreign substances may have adhered. Since this could cause a malfunction, immerse the camera in fresh water and shake it sufficiently in the water to remove the any foreign substances from the camera.
• When the camera is immersed in the water, a few air bubbles may come out from the water drain holes of the camera such as openings in the microphone or speakers. This is not a malfunction.
2. Wipe off water droplets with a soft cloth and dry the camera in the well-ventilated and shady place.
• Place the camera on a dry cloth to dry it.
Water will flow out from openings in the microphone or speakers.
• Do not dry the camera with hot air from a hair dryer or clothes dryer.
• Do not use chemicals (such as benzine, thinner, alcohol, or cleanser), soap, or neutral detergents.
If the waterproof packing or body of the camera becomes deformed, the waterproof performance will deteriorate.
xv
xvi
3. After making sure that there are no water droplets on the camera, open the battery-chamber/memory card slot cover and gently wipe off any water or sand remaining inside the camera with a dry soft cloth.
• If you open the cover before the camera is thoroughly dried, water droplets may fall on a memory card or battery.
The water droplets may also seep inside the battery-chamber/memory card slot cover (in locations such as waterproof packing, hinges, memory card slot, or terminals).
If that happens, wipe the water off with a dry soft cloth.
• If the cover is closed when the inside is wet, this could cause condensation or malfunction.
• If the microphone or speaker openings are clogged with water droplets, the sound may deteriorate or become distorted.
- Wipe the water off with a dry soft cloth.
- Do not puncture the microphone or speaker openings with a sharp implement. If the inside of the camera is damaged, the waterproof performance will deteriorate.
• See “Cleaning” (F7) for more information.
Notes About Operating Temperature and
Humidity and Condensation
The operation of this camera has been tested at temperatures from −10°C to
+40°C (14°F to 104°F).
When you use the camera in cold climate regions, observe the following precautions. Keep the camera and spare batteries in a warm place before use.
• The performance of the batteries (number of images shot and shooting time) will drop temporarily.
• If the camera is in a very cold state, the performance may drop temporarily, for example, the monitor may be darker than normal immediately after the camera is turned on or residual images may be produced.
• When snow or water droplets adhere to the exterior of the camera, immediately wipe them off.
- If the buttons or switches are frozen, they may not operate smoothly.
- If the microphone or speaker openings are clogged with water droplets, the sound may deteriorate or become distorted.
bOperating environmental conditions such as temperature and humidity may cause fogging
(condensation) on the inside of the monitor or lens. This is not the camera malfunction or defect.
bEnvironmental conditions that are likely to cause condensation inside of the camera
Fogging (condensation) may occur on the inside of the monitor or lens in the following environmental conditions where there are sharp temperature changes or high humidity.
• The camera is suddenly immersed in low temperature underwater from high temperature on land.
• The camera is brought to a warm place such as inside a building from the cold climate outside.
• The battery-chamber/memory card slot cover is opened or closed in a highhumidity environment.
bClearing the fogging
• Open the battery-chamber/memory card slot cover after turning off the camera in a place where the ambient temperature is stable (avoid any place that has high-temperature/high-humidity, sand or dust).
To clear the fogging, remove the battery and memory card, and leave the camera with the battery-chamber/memory card slot cover open to allow the camera to adjust to the ambient temperature.
• If the fogging does not clear, consult your retailer or Nikon-authorized service representative.
xvii
xviii
<Important> Notes About Location Data
Functions (GPS/GLONASS, Electronic
Compass)
bMap/location name data of this camera
Before using the location data functions, make sure to read “USER LICENSE
AGREEMENT FOR MAP DATA AND LOCATION NAME DATA” ( F20) and
agree to the terms.
• The maps and location name information (Points of Interest: POI) are as of
April 2013.
The maps and location name information will not be updated.
• The details of geological formations are displayed simplistically according to the scale of a map. The scale of a map and level of detail of the location data vary depending on country and region.
If the latitude becomes higher, the horizontal and vertical scales displayed on the monitor vary, therefore displayed geological formations differ from the actual formations. Use the maps and location name information only as a guide.
• The detailed map data and location name information (Points of Interest:
POI) of the People’s Republic of China (“China”) and the Republic of Korea are not provided for the COOLPIX AW120.
bNotes about record location data functions and log recording
• When Record location data in Location data options of the Location data options menu is set to On or while recording logs, record location data functions and log recording will continue to operate even after the camera is turned off (
The electromagnetic waves emitted by this camera may disrupt the electronic systems of the airplane or the instruments of the hospital. When use of the camera is prohibited or restricted during airplane takeoffs and landings or inside a hospital, end log recording, set Record location data to Off, and then turn off the camera.
• An individual may be identified from still images or movies that have been recorded with location data. Observe caution when you transfer still images or movies recorded with location data, or log files to a third party or upload them to a network such as the Internet where the public can view them. Make sure to read
“Disposing of Data Storage Devices” ( Avi).
bNotes about measurement functions
The COOLPIX AW120 is a camera. Do not use this camera as a navigation device or measuring instrument.
• Use information (such as direction, altitude and water depth) measured by the camera as a guideline only. Do not use this information for navigation of an airplane, car, and person or land survey applications.
• When you use the camera for mountain climbing, trekking, or underwater, make sure to take a map, navigation device, or measuring instrument separately.
bUsing the camera overseas
• Before taking the camera with location data functions overseas for travel, consult your travel agency or embassy of the country you are visiting to confirm whether there is any restriction on use.
For example, you cannot record location data logs without permission from the government in China.
Set Record location data to Off.
• The location data may not function properly in China and on the borders between China and neighboring countries (as of December 2013).
xix
xx
Wi-Fi (Wireless LAN Network)
This product is controlled by the United States Export Administration
Regulations, and you are required to obtain permission from the United States government if you export or re-export this product to any country to which the
United States embargoes goods. The following countries were subject to embargo: Cuba, Iran, North Korea, Sudan, and Syria. Since the target countries are subject to change, please contact the United States Department of
Commerce for the latest information.
Restrictions on Wireless Devices
The wireless transceiver included in this product conforms to wireless regulations in the country of sale and is not for use in other countries (products purchased in the EU or EFTA can be used anywhere within the EU and EFTA).
Nikon does not accept liability for use in other countries. Users who are unsure as to the original country of sale should consult with their local Nikon service center or Nikon-authorized service representative. This restriction applies to wireless operation only and not to any other use of the product.
Notice for Customers in the U.S.A. and Canada
Federal Communications Commission (FCC) and Industry of Canada
(IC)
Declaration of Conformity
This device complies with Part 15 of FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
FCC/IC RF Exposure Statement
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research.
COOLPIX AW120, which is equipped with a DW092 (FCC ID:EW4DW092/IC
ID:4634A-3149EC) Wireless LAN Module, has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Please refer to the SAR test report that was uploaded to FCC website.
Declaration of Conformity (Europe)
Hereby, Nikon Corporation, declares that COOLPIX AW120 is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC. The declaration of conformity may be consulted at http://imaging.nikon.com/support/pdf/DoC_AW120.pdf.
Notice for customers in Singapore
This device complies with radio-frequency regulations.
Complies with
IDA Standards
DA103423
Notice for Customers in Jamaica
This product contains a Type Approved Module by Jamaica:
“SMA - DW092”
xxi
xxii
Precautions when Using Radio Transmissions
Always keep in mind that radio transmission or reception of data is subject to interception by third parties. Note that Nikon is not responsible for data or information leaks that may occur during data transfer.
Personal Information Management and Disclaimer
• User information registered and configured on the product, including wireless LAN connection settings and other personal information, is susceptible to alteration and loss resulting from operational error, static electricity, accident, malfunction, repair or other handling. Always keep separate copies of important information. Nikon is not responsible for any direct or indirect damages or lost profits resulting from alteration or loss of content that is not attributable to Nikon.
• Before discarding this product or transferring it to another owner, perform
Restore default settings in the Wi-Fi options menu ( E92) to delete all
user information registered and configured with the product, including wireless LAN connection settings and other personal information.
Table of Contents
<Important> Shockproof, Waterproof, Dustproof, Condensation....................... xii
Notes About Operating Temperature and Humidity and Condensation ........... xvii
<Important> Notes About Location Data Functions (GPS/GLONASS,
Preparation 4 Setting the Display Language, Date, and Time ............................... 18
xxiii
xxiv
Special Effects Mode (Applying Effects When Shooting)......................................... 42
Smart Portrait Mode (Capturing Images of Smiling Faces) ..................................... 44
Functions That Can Be Set with the d Button (Shooting Menu) ..................... 55
Functions That Can Be Set with the d Button (Playback Menu) ...................... 67
Functions That Can Be Set with the d Button (Movie Menu) ................................ 73
Functions That Can Be Set with the d Button (Setup Menu) ............................ 76
Using Location Data Functions/Displaying Maps ....................................... 78
Functions That Can Be Set Using the d Button (Location Data Options
Using the Wi-Fi (Wireless LAN) Function ........................................................ 89
Connecting the Camera to a TV, Computer, or Printer.............................. 92
Using Easy Panorama (Shooting and Playback) ..................................................... E2
xxv
xxvi
Viewing and Deleting Images Captured Continuously (Sequence)............. E11
Red-eye Correction: Correcting Red-eye When Shooting with the Flash .... E16
Data Imprint: Imprinting Information such as Altitude and Direction
Connecting the Camera to a TV (Viewing Images on a TV) ............................. E21
Connecting the Camera to a Printer (Direct Print).............................................. E22
Copy (Copy Between Internal Memory and Memory Card).................................. E52
xxvii
xxviii
Points of Interest (POI) (Recording and Displaying Location Name
Create Log (Record the Log of Movement Information) ........................................ E83
USER LICENSE AGREEMENT FOR MAP DATA AND LOCATION NAME
Parts of the Camera
The Camera Body
1 2 3 4 5 6 7
8 9 10 11 12 13
1
Eyelet for camera strap.........................3
2
Shutter-release button....................28
3
Power switch/power-on lamp....22
4
Flash............................................................48
5
Positioning antenna .........................78
6
Self-timer lamp.....................................50
AF-assist illuminator..........................76
Movie light..............................................73
7 Lens
14
8
HDMI micro connector
(Type D) .................................................... 92
9
Hinge..........................................................xiii
10
Waterproofing packing ..................xiii
11
Micro-USB connector....................... 92
12
13
Battery-chamber/memory card
slot cover latch release............ 12, 16
Battery-chamber/memory card
slot cover latch............................. 12, 16
14
Microphone (stereo)................. 67, 69
1
1 2 3 4 5 6 7 8 9
2
10 11 12 13 14 15
1
Eyelet for camera strap.........................3
2
Speaker ..................................... 67, 74, 76
3
OLED monitor (monitor)*.........8, 22
4
Zoom control........................................27
f : wide-angle..........................27
g : telephoto.............................27
h : thumbnail playback ......66
i : playback zoom .................65
j : help .........................................35
5
Flash lamp...............................................48
6 b (e movie-record) button
........................................................................69
7
c (playback) button.......................30
* Also referred to as the “monitor” in this manual.
8
k (apply selection) button............6
9
Multi selector ...........................................6
10
U (map) button ................................. 82
11
V (action) button.................................4
12 Tripod socket
13
A (shooting mode) button....... 24
14 d (menu) button
...................................6, 55, 67, 73, 76, 87
15
l (delete) button ...................... 31, 75
Attaching the Camera Strap for Land Use
Remove the strap for land use before using the camera underwater.
3
4
Using the
V (Action) Button (Action
Control)
When the V (action) button is pressed, you can perform the function by shaking the camera.
As shown in the illustration, use your wrist and shake the camera for a single up/down or forward/backward stroke to perform the functions.
Easy auto mode
Confirm
Action menu
In the action menu, you can select the following options by shaking the camera up/down or forward/backward.
Press the V (action) button to select the function.
• Shooting mode: You can select the Easy auto mode, Auto mode, Beach,
Snow, Landscape and Underwater modes.
• Start movie recording: Press the V (action) button to begin recording.
Press the button again to exit recording.
• Quick playback: Display images in full-frame playback mode.
• Current position: Display the current position on a map (only when the location data has been obtained (
Notes About Playback Action Control
When Playback action control in the setup menu (
shake the camera up/down to display the next image or forward/backward to display the previous image in full-frame playback mode.
Action Control
The following operations can be performed while the map is displayed.
• You can scroll the map when you tilt the camera while pressing the V (action) button.
• You can zoom in the map by shaking the camera once, and zoom out by shaking it
twice when Map actions in setup menu ( A76) is set to On.
B
Notes About Action Control
• When using the action control, make sure to hold the camera firmly by passing your hand through the camera strap.
• In the action control, only the V (action) button, shutter-release button and power switch can be used.
• Action control may not perform well depending on how the camera is shaken.
Change the Action control response ( A77).
5
6
Using Menus (the
d Button)
Use the multi selector and k button to navigate the menus.
1
Press the d button.
• The menu is displayed.
40
30
20
10
0
-10
15m
1010hPa
25m 0s
880
2
Press the multi selector
J.
• The current menu icon is displayed in yellow.
Easy auto mode
Image mode
3
Select the desired
4 menu icon.
• The menu is changed.
Press the k button.
• The menu options become selectable.
Menu icons
Set up
Welcome screen
Time zone and date
Monitor settings
Print date
Photo VR
Motion detection
AF assist
Welcome screen
Time zone and date
Monitor settings
Print date
Photo VR
Motion detection
AF assist
5
Select a menu option.
6
Press the k button.
• The settings for the option you selected are displayed.
Welcome screen
Time zone and date
Monitor settings
Print date
Photo VR
Motion detection
AF assist
Photo VR
On (hybrid)
On
Off
7
Select a setting.
Photo VR
On (hybrid)
On
Off
8
Press the k button.
• The setting you selected is applied.
• When you are finished using the menu, press the d button.
C
Notes About Setting Menu Options
• Certain menu options cannot be set depending on the current shooting mode or the state of the camera. Unavailable options are displayed in gray and cannot be selected.
• When a menu is displayed, you can switch to shooting mode by pressing the shutter-release button or b (e movie-record) button.
7
8
The Monitor
The information that is displayed in the monitor during shooting and playback changes depending on the camera’s settings and state of use.
By default, information is displayed when the camera is first turned on and when you operate the camera, and turns off after a few seconds (when Photo
info is set to Auto info in Monitor settings ( A76)).
Shooting Mode
45
44
43
41
42
40
39
1
2
36
37
38
29
28
32 31 30
3
4
5
13
14
11 12
15
9
10
6
7
8
25
24 a b
27 26
23
22
21 20
17
19
16
18
47 a b
46
40
30
20
10
0
-10
15m
1010hPa
48
1
Shooting mode............................ 24, 25
2
Flash mode.............................................48
3
Macro mode ..........................................51
4
Zoom indicator ............................ 27, 51
5
Focus indicator.....................................28
6
Movie options (normal speed
movies)..................................... 73,
7
Movie options (HS movies)
....................................................... 73,
8
Image mode ......................... 56,
9
Easy panorama.....................................39
10
Vibration reduction icon ........ 73, 76
11
Motion detection icon ....................76
12
Wind noise reduction ......................73
13
Exposure compensation value
........................................................................52
14
Movie recording time remaining
........................................................................69
15
Number of exposures remaining
(still images) ...........................................22
16
Internal memory indicator............22
17
Aperture value......................................29
18
Focus area (target finding AF)
................................................................ 56, 61
19
Focus area (for manual or center)
................................................................ 56, 64
20
21
Focus area (face detection,
pet detection)............... 40, 44, 56, 62
Focus area (subject tracking)
....................................................... 56,
22
Shutter speed .......................................29
23
ISO sensitivity ........................................56
24
(a) Battery level indicator ...............22
(b) Charging AC adapter connection indicator
25
Print date .................................................76
26 Travel destination icon...........
27
“Date not set” indicator...................18
28
29
Eye-Fi communication indicator
.......................................................................77
Wi-Fi communication indicator
.......................................................................89
30
Save location........................................ 82
31
Log display (Location data)
............................................................... 83, 88
32
Location data reception.................80
33
Atmospheric pressure .....................86
34
Altitude/water depth.......................86
35
Log display (altitude/water depth)
............................................................... 83, 88
36
White balance mode........................56
37
Skin softening .......................................57
38
Quick effects icon....................... 46, 56
39
Continuous shooting mode........56
40
Blink proof icon....................................57
41
Hand-held/tripod ....................... 36, 37
42
Backlighting (HDR).............................38
43
Self-timer indicator............................50
44
Smile timer .............................................57
45
Pet portrait auto release.................40
46
Altimeter/depth gauge ..................86
47
48
Compass display .................................88
(a) Direction gauge
(b) Compass
Location name information (POI
information)...........................................88
9
10
Playback Mode
1 2 3
32
12 13
25 a b
29
27 28
26
9999. JPG
15/05/2014 15:30
24 23
22 21
1918
20
14
15
16
17 a b
1
Album icon in favorite pictures mode....................................................
2
Category icon in auto sort mode
..................................................................
3 List by date icon .........................
4
Protect icon........................... 67,
5
Sequence display (when
Individual pictures is selected)
....................................................... 68,
6
Print order icon ................... 67,
7
8
9
Quick effects icon.......30, 46,
10
D-Lighting icon................... 67,
11
Quick retouch icon ........... 67,
12
Red-eye correction ........... 67,
13
Internal memory indicator............22
14
(a) Current image number/ total number of images
(b) Movie length
15
Image mode ......................... 56,
16
Easy panorama.....................................39
17
Movie options...................... 73,
18
Small picture icon ............. 67,
19
Crop icon ................................ 65,
20
Volume indicator ............... 74,
21
Quick effects guide ...........................30
22
Easy panorama playback guide
......................................................... 39,
Sequence playback guide
...................................................... 68,
Movie playback guide .....................74
23 Time of recording
24 Date of recording
25
(a) Battery level indicator ...............22
(b) Charging AC adapter connection indicator
26 File number and type .............
27
28
Recorded location data indicator
.......................................................................80
Eye-Fi communication indicator
...................................................... 77,
29
Atmospheric pressure .....................86
30
Altitude/water depth.......................86
31
Compass display (compass) ........88
32
Location name information (POI
information)...........................................88
11
12
The Basics of Shooting and
Playback
Preparation 1 Insert the Battery
1
Press the battery-chamber/ memory card slot cover latch release ( 1 ) and rotate the batterychamber/memory card slot cover latch ( 2 ) to open the cover ( 3 ).
2
Insert the battery.
• Push the orange battery latch in the direction indicated by the arrow (1), and fully insert the battery (2).
• The battery locks into place when inserted correctly.
Battery latch
B
Be Careful to Insert the Battery in
Correct Direction
Inserting the battery upside down or backwards could damage the camera.
3
Push the battery-chamber/ memory card slot cover to the camera ( 1 ) and rotate the batterychamber/memory card slot cover latch until the cover is locked ( 2 ).
• Rotate the battery-chamber/memory card slot cover latch until it clicks into place.
B
Notes About Closing the Cover without Getting the Camera Strap or Cord Caught
If the camera strap’s cord gets caught in the battery-chamber/memory card slot cover when it is closed, the cover could be damaged. Before closing the batterychamber/memory card slot cover, make sure that the strap or cord does not get caught in it.
Removing the Battery
Turn the camera off and make sure that the power-on lamp and the monitor have turned off, and then open the battery-chamber/memory card slot cover.
Move the battery latch in the direction indicated by the arrow (1) to eject the battery (2).
B
High Temperature Caution
The camera, battery, and memory card may be hot immediately after using the camera.
B
Opening/Closing the Battery-Chamber/Memory Card Slot Cover
Do not open and close the battery-chamber/memory card slot cover in a sandy or dusty environment or with wet hands. If the cover is closed without removing foreign particles, water may seep inside the camera or the camera may become damaged.
• If foreign particles get inside the cover or camera, immediately remove them with a blower or brush.
• If liquid such as water gets inside the cover or camera, immediately wipe it off with a soft and dry cloth.
13
Preparation 2 Charge the Battery
1
Prepare the included charging AC adapter.
If a plug adapter* is included with your camera, attach the plug adapter to the plug on the charging AC adapter.
Push the plug adapter firmly until it is securely held in place. Once the two are connected, attempting to forcibly remove the plug adapter could damage the product.
* The shape of the plug adapter varies according to the country or region in which the camera was purchased.
This step can be omitted if the plug adapter comes permanently bonded to the charging AC adapter.
2
Make sure the battery is installed in the camera, and then connect the camera to the charging AC adapter in order of
1 to 3.
• Keep the camera turned off.
• Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them.
B
Notes
Do not use a USB cable other than the UC-E21. Using a USB cable other than the
UC-E21 could result in overheating, fire or electric shock.
Charge lamp
Electrical outlet
14
USB cable (included)
• The charge lamp slowly flashes green to indicate that the battery is charging.
Charge lamp
Flashes slowly
(green)
The battery is charging.
Description
Off
Flashes quickly
(green)
When charging is complete, the charge lamp stops flashing green and turns off. About 2 hours and 20 minutes are required to charge a fully exhausted battery.
• The ambient temperature is not suited to charging. Charge the battery indoors with an ambient temperature of 5°C to
35°C (41°F to 95°F).
• The USB cable or charging AC adapter is not properly connected, or there is a problem with the battery.
Disconnect the USB cable or unplug the charging AC adapter and correctly connect it again, or change the battery.
3
Disconnect the charging AC adapter from the electrical outlet and then disconnect the USB cable.
B
Notes About Charging
Do not, under any circumstances, use another make or model of AC adapter other than Charging AC Adapter EH-71P, and do not use a commercially available USB-AC adapter or a battery charger for a mobile phone. Failure to observe this precaution could result in overheating or in damage to the camera.
C
Charging Using a Computer or Battery Charger
• You can also charge the battery by connecting the camera to a computer (A92,
• You can use the Battery Charger MH-65 (available separately; E101) to charge
the battery without using the camera.
15
16
Preparation 3 Insert a Memory Card
1
Turn off the camera and open the battery-chamber/memory card slot cover.
2
Insert the memory card.
• Slide the memory card in until it clicks into place.
Memory card slot
B
Be Careful to Insert the Memory Card in Correct Direction
Inserting the memory card upside down or backwards could damage the camera and the memory card.
3
Close the battery-chamber/ memory card slot cover.
B
Notes About Closing the Cover without Getting the Camera Strap or Cord Caught
If the camera strap’s cord gets caught in the battery-chamber/memory card slot cover when it is closed, the cover could be damaged. Before closing the batterychamber/memory card slot cover, make sure that the strap or cord does not get caught in it.
B
Formatting Memory Cards
The first time you insert a memory card that has been used in another device into this camera, make sure to format it with this camera. Insert the card into the camera, press the d button, and select Format card in the setup menu.
Removing Memory Cards
Turn the camera off and make sure that the power-on lamp and the monitor have turned off, and then open the battery-chamber/memory card slot cover.
Gently push the memory card into the camera
(1) to partially eject the card (2).
B
High Temperature Caution
The camera, battery, and memory card may be hot immediately after using the camera.
Internal Memory and Memory Cards
Camera data, including images and movies, can be saved either in the camera’s internal memory or on a memory card. To use the camera’s internal memory, first remove the memory card.
17
18
Preparation 4 Setting the Display
Language, Date, and Time
When the camera is turned on for the first time, the language-selection screen and the date and time setting screen for the camera clock are displayed.
• If you exit without setting the date and time, O will flash when the shooting screen is displayed.
1
Press the power switch to turn on the camera.
2
Use the multi selector
HI to select the desired language and press the k button.
3
Select Yes and press the k button.
Language
Български
Čeština
Dansk
Deutsch
English
Español
Cancel
Choose time zone and set date and time?
Yes
No
Cancel
4
Select your home time zone and press the k button.
• To enable daylight saving time, press H. When the daylight saving time function is enabled, W is displayed above the map.
To turn off the daylight saving time function, press I.
London, Casablanca
Back
5
Select the date format and press the k button.
Date format
Year/Month/Day
Month/Day/Year
Day/Month/Year
6
Set the date and time, and press the k button.
• Select a field: Press JK (changes between
D, M, Y, h, and m).
• Edit the date and time: Press HI.
• Confirm the setting: Select the m field and press the k button.
7
Select Yes and press the k button.
Date and time
D M Y
15 05 2014 h m
15 30
Edit
15/05/2014 15:30
OK?
Yes
No
19
20
8
Read the message about the waterproof function, and press K.
• There are 6 message screens.
Do not open the covers by the water or in sandy locations, as foreign matter could enter the camera.
1/6
9
When you have read the message shown on the right, press the k button.
• The camera switches to shooting mode
(
After drying thoroughly, use a cloth to remove any droplets remaining on the areas indicated.
6/6 Exit
C
Changing the Language Setting and the Date and Time Setting
• You can change these settings using the Language and Time zone and date
settings in the z setup menu ( A76).
• You can enable or disable daylight saving time in the z setup menu by selecting
Time zone and date followed by Time zone. Enabling daylight saving time moves the clock forward one hour, and disabling it moves the clock back one hour.
C
The Clock Battery
• The camera’s clock is powered by a built-in backup battery.
The backup battery charges when the main battery is inserted into the camera or when the camera is connected to an optional AC adapter, and it can run the clock for several days after about 10 hours of charging.
• If the camera’s backup battery becomes exhausted, the date and time setting screen is displayed when the camera is turned on. Set the date and time again. See step 3 (
A18) of “Preparation 4 Setting the Display Language, Date, and Time” for
more information.
C
Imprinting the Shooting Date on Printed Images
• You can permanently imprint the shooting date on images as they are captured by
setting Print date in the setup menu ( A76).
• If you want the shooting date to be printed without using the Print date setting,
print using the ViewNX 2 software ( A94).
21
22
Step 1 Turn the Camera On
1
Press the power switch.
• The monitor turns on.
• To turn the camera off, press the power switch again.
• Note that the power switch is enabled a few seconds after the battery is inserted. Wait a few seconds before pressing the power switch.
2
Check the battery level indicator and the number of exposures remaining.
40
30
20
10
0
-10
15m
1010hPa Battery level indicator
Number of exposures remaining
Battery level indicator
Display b
B
N
Battery exhausted.
Description
The battery level is high.
The battery level is low.
The camera cannot capture images. Recharge the battery.
Number of Exposures Remaining
The number of images that can be taken is displayed.
• C is displayed when no memory card is inserted in the camera, and images are saved in the internal memory.
C
The Auto Off Function
Flashes
No operations performed
No operations performed
40
30
20
10
0
-10 3 min
Camera enters standby mode.
Camera turns off.
• The time that elapses before the camera enters standby mode is about 1 minute.
The time can be changed using the Auto off setting in the setup menu ( A76).
• While the camera is in standby mode, the monitor turns back on if you perform any of the following operations:
➝ Press the power switch, shutter-release button, A (shooting mode) button, c
(playback) button, or b (e movie-record) button
• While the charging AC adapter is connected to the camera, the monitor turns back on if you press the power switch. The camera turns off if you press the shutterrelease button, A (shooting mode) button, c (playback) button, or b (e movie-record) button.
23
24
Step 2 Select a Shooting Mode
1
Press the
A button.
2
Use the multi selector HI to select a shooting mode and press the k button.
• G (easy auto) mode is used in this example.
Multi selector
• The selected shooting mode is saved even if the power is turned off.
Easy auto mode
Available Shooting Modes
G b
D
F
A
Easy auto mode
The camera automatically selects the optimum scene mode when you frame an image, making it even easier to take images using settings that suit the scene.
Scene mode
Camera settings are optimized according to the scene that you select.
Special effects
Effects can be applied to images during shooting.
Smart portrait
The camera detects smiling faces and releases the shutter automatically.
Auto mode
Used for general shooting. Settings can be adjusted to suit the shooting conditions and the type of shot you want to capture.
25
26
Step 3 Frame a Picture
1
Hold the camera steady.
• Keep fingers and other objects away from the lens, flash, AF-assist illuminator, microphone, and speaker.
• When taking pictures in portrait (“tall”) orientation, turn the camera so that the flash is above the lens.
2
Frame the picture.
• When the camera automatically determines the scene mode, the shooting mode icon
Shooting mode icon
40
30
20
10
0
-10
15m
1010hPa
B
Notes About Easy Auto Mode
• Depending upon shooting conditions, the camera may not select the desired scene mode. In this case, select another shooting mode (
• When the digital zoom is in effect, the scene mode changes to U.
C
When Using a Tripod
• We recommend using a tripod to stabilize the camera in the following situations.
- When shooting in dim lighting
- When shooting with the flash mode (
- When using the telephoto setting
• When using a tripod to stabilize the camera during shooting, set Photo VR to Off
in the setup menu ( A76) to prevent potential errors caused by this function.
Using the Zoom
When you move the zoom control, the zoom lens position changes.
• To zoom in closer to the subject: Move toward g (telephoto)
• To zoom out and view a larger area: Move toward f (wide-angle)
When you turn the camera on, the zoom moves to the maximum wide-angle
Zoom in position.
• A zoom indicator is displayed at the top of the shooting screen when the zoom control is moved.
• Digital zoom, which allows you to further magnify the subject up to approximately 4×
Optical zoom
Zoom out
Digital zoom the maximum optical zoom ratio, can be activated by moving and holding the zoom control toward g when the camera is zoomed in to the maximum optical zoom position.
C
Notes About Digital Zoom
The zoom indicator turns blue when the digital zoom is activated, and it turns yellow when the zoom magnification is increased further.
• Zoom indicator is blue: Image quality is not noticeably reduced by using the
Dynamic Fine Zoom.
• Zoom indicator is yellow: Image quality is noticeably reduced.
• The indicator remains blue across a wider area when the image size is smaller.
27
28
Step 4 Focus and Shoot
1
Press the shutter-release button halfway.
• When the subject is in focus, the focus area that includes the subject or focus
indicator ( A9) glows green (multiple
focus areas can glow green).
• When you are using digital zoom, the camera focuses on the subject in the center of the frame and the focus area is not displayed. When the camera has
focused, the focus indicator ( A9) glows
green.
• If the focus area or focus indicator flashes red, the camera is unable to focus. Modify the composition and try pressing the shutter-release button halfway again.
2
Without lifting your finger, press the shutter-release button the rest of the way down.
The Shutter-release Button
Press halfway
To set focus and exposure (shutter speed and aperture value), press the shutter-release button lightly until you feel a slight resistance.
Focus and exposure remain locked while the shutter-release button is pressed halfway.
Press all the way
Press the shutter-release button all the way to release the shutter and take an image.
Do not use force when pressing the shutterrelease button, as this may result in camera shake and blurred images. Press the button gently.
B
Notes About Saving Images and Recording Movies
The indicator showing the number of exposures remaining or the indicator showing the maximum movie length flashes while images are being saved or while a movie is being recorded. Do not open the battery-chamber/memory card slot cover or
remove the battery or memory card while an indicator is flashing. Doing this could result in loss of data, or in damage to the camera or the memory card.
29
30
Step 5 Play Back Images
1
Press the c (playback) button.
• If you press and hold down the c (playback) button while the camera is turned off, the camera turns on in playback mode.
2
Use the multi selector to select an image to display.
• Press and hold down HIJK to scroll through the images quickly.
Display the previous image
Display the next image
• To return to shooting mode, press the A button or shutter-release button.
15m
1010hPa
0004. JPG
15/05/2014 15:30
C
Notes About the Quick Effects Function
• When e is displayed in full-frame playback mode, you can press the k button to apply an effect to the image.
• When the effect selection screen is displayed, use the multi selector JK to select an effect, press the k button, and then select Yes in the confirmation dialog and press the k button to
15m
1010hPa
0004. JPG
15/05/2014 15:30 save the image as a separate file.
See “Quick Effects: Changing Hue or Mood” ( E14) for more information.
Step 6 Delete Images
1
Press the l button to delete the image currently displayed in the monitor.
2
Use the multi selector HI to select the desired deletion method and press the k button.
• To exit without deleting, press the d button.
3
Select Yes and press the k button.
• Deleted images cannot be recovered.
• To cancel, select No and press the k button.
Delete
Current image
Erase selected images
All images
Erase 1 image?
Yes
No
31
32
Operating the Erase Selected Images Screen
1
Use the multi selector JK to select an image to be deleted, and then use
H to display K.
• To undo the selection, press I to remove
K.
• Move the zoom control (A2) toward g (i)
to switch to full-frame playback or f (h) to switch to thumbnail playback.
Erase selected images
Back
2
Add
K to all images that you want to delete and then press the k button to confirm the selection.
• A confirmation dialog is displayed. Follow the instructions displayed in the monitor.
B
Deleting Images in a Sequence
• If you press the l button and delete a key picture while only key pictures are
displayed for sequences of images ( A68), all images in the sequence, including
the key picture, are deleted.
• To delete individual images in a sequence, press the k button to display them one at a time and press the l button.
C
Deleting the Last Image Captured While in Shooting Mode
When using shooting mode, press the l button to delete the last image that was saved.
Shooting Features
G (Easy Auto) Mode
The camera automatically selects the optimum scene mode when you frame a picture, making it even easier to take pictures using settings that suit the scene.
Display the shooting screen M A (shooting mode) button M G (easy auto) mode M k button
When the camera selects a scene mode, the shooting mode icon displayed on the shooting screen changes to that for the scene mode currently enabled.
e f h g
Portrait
Landscape
Night portrait
Night landscape i Close-up j Backlighting a Underwater
*
U Other scenes
*
The camera is switched to underwater mode when it is lowered into water.
When the camera detects it is underwater while Record location data in
Location data options is set to On and positioning has been performed, the screen to choose whether to record location data on the image that is shot underwater is displayed. When you select Yes or No and press the k button, the shooting screen is displayed.
• The focus area depends on the composition of the image. When the camera detects a human face, it focuses on that face (
33
34
B
Note after Taking the Camera out of the Water
After taking the camera out of water, sometimes it may not automatically switch to another scene from underwater mode.
Gently brush any water droplets with your hand from the camera or wipe it off with a
soft and dry cloth. See “Cleaning after Using the Camera Underwater” ( Axv) for
more information on caring for the camera.
Functions That Can Be Set Using G (Easy Auto) Mode
Scene Mode (Shooting Suited to Scenes)
When a scene is selected, camera settings are automatically optimized for the selected scene.
Display the shooting screen M A (shooting mode) button M b (the second icon from the top*) M K M HI M select a scene M k button
* The icon of the last scene selected is displayed.
b Portrait (default setting) c Landscape
Z Beach
2 z Snow 2 h Sunset 2, 3 i Dusk/dawn
1
1, 3
2
e Night portrait (A36) f Party/indoor (A36)
2
1
2
1, 3
2
2
O Pet portrait (
C Underwater (
2
1
2
3
The camera focuses at infinity.
The camera focuses on the area in the center of the frame.
Use of a tripod is recommended because the shutter speed is slow. Set Photo VR to Off in the setup menu (
A76) when using a tripod to stabilize the camera
during shooting.
To View a Description (Help Display) of Each Scene
Select a scene and move the zoom control ( A2) toward g (j) to view a
description of that scene. To return to the original screen, move the zoom control toward g (j) again.
35
36
Tips and Notes
d Sports
• While the shutter-release button is held all the way down, the camera shoots up to about 5 images continuously at a rate of about 6.9 fps (when image mode is set to
P 4608×3456).
• The frame rate for continuous shooting may become slow depending upon the current image mode setting, the memory card used, or shooting condition.
• Focus, exposure, and hue are fixed at the values determined with the first image in each series.
e Night portrait
• From the screen displayed after e Night portrait is selected, select Hand-held or Tripod.
• Hand-held (default setting):
- When the e icon at the top left of the monitor glows green, press the shutter-release button all the way to capture a series of images which are combined into a single image and saved.
- Once the shutter-release button is pressed all the way, hold the camera still until a still image is displayed. After taking an image, do not turn the camera off before the monitor switches to the shooting screen.
- If the subject moves while the camera is shooting continuously, the image may be distorted, overlapped, or blurred.
• Tripod:
- One image is captured at a slow shutter speed when the shutter-release button is pressed all the way.
- Vibration reduction is disabled regardless of the Photo VR ( A76) setting in the
setup menu.
f Party/indoor
• To avoid the effects of camera shake, hold the camera steady. Set Photo VR to Off
in the setup menu ( A76) when using a tripod to stabilize the camera during
shooting.
j Night landscape
• From the screen displayed after j Night landscape is selected, select Hand-
held or Tripod.
• Hand-held (default setting):
- When the j icon at the top left of the monitor glows green, press the shutter-release button all the way to capture a series of images which are combined into a single image and saved.
- Once the shutter-release button is pressed all the way, hold the camera still until a still image is displayed. After taking an image, do not turn the camera off before the monitor switches to the shooting screen.
- The angle of view (i.e., the area visible in the frame) seen in the saved image is narrower than that seen in the monitor at the time of shooting.
• Tripod:
- One image is captured at a slow shutter speed when the shutter-release button is pressed all the way.
- Vibration reduction is disabled regardless of the Photo VR ( A76) setting in the
setup menu.
k Close-up
• Macro mode (A51) is enabled and the camera automatically zooms to the closest
position at which it can focus.
• You can move the focus area. Press the k button, use the multi selector HIJK to move the focus area, and press the k button to apply the setting.
u Food
• Macro mode (A51) is enabled and the camera automatically zooms to the closest
position at which it can focus.
• You can adjust hue by using the multi selector
HI. The hue setting is saved in the camera’s memory even after the camera is turned off.
• You can move the focus area. Press the k button, use the multi selector HIJK to move the focus area, and press the k button to apply the setting.
40
30
20
10
0
-10
15m
1010hPa
37
38 l Museum
• The camera captures a series of up to 10 images while the shutter-release button is held all the way down, and the sharpest image in the series is automatically selected and saved (BSS (Best Shot Selector)).
• The flash does not fire.
m Fireworks show
• The shutter speed is fixed at about 4 seconds.
n Black and white copy
• Use together with macro mode (A51) when shooting subjects that are close to
the camera.
o Backlighting
• From the screen displayed after o Backlighting is selected, select o or k to enable or disable the high dynamic range (HDR) function based on the type of image you want to take.
• k (default setting): The flash fires to prevent the subject from being hidden in shadow.
- When the shutter-release button is pressed all the way down, one image is captured.
• o: Use when taking images with very bright and dark areas in the same frame.
- When the shutter-release button is pressed all the way, the camera shoots images continuously at high speed, and saves the following two images.
- A non-HDR composite image
- An HDR composite image in which the loss of details in highlights or shadows is minimized
- If there is only enough memory to save one image, an image processed by D-
Lighting (
A67) at the time of shooting, in which dark areas of the image are
corrected, is the only image saved.
- Once the shutter-release button is pressed all the way, hold the camera still until a still image is displayed. After taking an image, do not turn the camera off before the monitor switches to the shooting screen.
- The angle of view (i.e., the area visible in the frame) seen in the saved image is narrower than that seen in the monitor at the time of shooting.
p Easy panorama
• From the screen displayed after p Easy panorama is selected, select the shooting range from Normal (180°) or Wide (360°).
• The zoom position is fixed at wide-angle.
• Press the shutter-release button all the way down, remove your finger from the button, and then slowly pan the camera horizontally. Shooting ends when the camera captures the specified shooting range.
• Focus and exposure are locked when shooting starts.
• If you press the k button when a captured image is displayed in full-frame playback mode, the image scrolls automatically.
• You cannot use any image editing functions other than cropping for images captured with easy panorama on this camera.
See “Using Easy Panorama (Shooting and Playback)” ( E2) for more information.
B
Notes About Printing Panorama Images
The entire image may not be able to be printed depending on the printer’s settings.
Additionally, printing may not be possible depending on the printer.
39
40
O Pet portrait
• When you point the camera at a dog or cat, the camera detects the pet’s face and focuses on it. By default, the shutter is automatically released when the camera detects a dog or cat face (pet portrait auto release).
• From the screen displayed after O Pet portrait is selected, select Single or
Continuous.
- Single: Whenever the camera detects a dog or cat face, the camera captures 1 image.
- Continuous: Whenever the camera detects a dog or cat face, the camera captures 3 images continuously.
B
Pet Portrait Auto Release
• Press the multi selector J (n) to change the Pet portrait auto release settings.
- Y: When the camera detects a dog or cat face, the camera automatically releases the shutter.
- k: The camera does not release the shutter automatically, even if a dog or cat face is detected. Press the shutter-release button. The camera also detects human faces when k is selected.
• Pet portrait auto release is set to k after five bursts have been taken.
• Shooting is also possible by pressing the shutter-release button, regardless of the
Pet portrait auto release setting.
B
Focus Area
• When the camera detects a face, the face is displayed inside a yellow border. When the camera acquires focus on a face displayed inside a double border (focus area), the double border turns green. If no faces are detected, the camera focuses on the subject in the center of the frame.
• In some shooting conditions, the pet face may not be detected and other subjects may be displayed inside a border.
40
30
20
10
0
-10
15m
1010hPa
C Underwater
• If you select Underwater, screens about recording of location data (A81) and
water depth calibration are displayed followed by messages about waterproofing
(refer to the back side of the front cover). The next message is displayed when you press the multi selector K after reading the messages. When the shutter-release button is pressed, the camera switches to shooting mode without displaying any subsequent screens.
• See “<Important> Shockproof, Waterproof, Dustproof, Condensation” (Axii) for
more information on shooting underwater.
41
42
Special Effects Mode (Applying Effects
When Shooting)
Effects can be applied to images during shooting.
Display the shooting screen M A (shooting mode) button M D (the third icon from the top*) M K M HI M Select the effect M k button
* The last icon you selected is displayed.
Category
D Soft
(default setting)
E Nostalgic sepia
F High-contrast monochrome
G High key
H Low key
I Selective color l Pop k Super vivid o Cross process m Toy camera effect 1 n Toy camera effect 2
Description
Softens the image by adding a slight blur to the entire image.
Adds a sepia tone and reduces the contrast to simulate the qualities of an old photograph.
Changes the image to black and white and gives it sharp contrast.
Gives the entire image a bright tone.
Gives the entire image a dark tone.
Creates a black and white image in which only the specified color remains.
Increases the color saturation of the entire image to create a bright look.
Increases the color saturation of the entire image and sharpens the contrast.
Gives the image a mysterious appearance based on a specific color.
Gives the entire image a yellowish hue and darkens the image periphery.
Decreases the color saturation of the entire image and darkens the image periphery.
• The camera focuses on the area in the center of the frame.
• When Selective color or Cross process is selected, use the multi selector HI to select the desired color from the slider.
To change settings for any of the following functions, press the k button to end color selection.
- Flash mode (
- Self-timer (
- Exposure compensation ( A52)
To return to the color selection screen, press the k button again.
Save
Slider
43
44
Smart Portrait Mode (Capturing Images of
Smiling Faces)
When the camera detects a smiling face, you can take an image automatically
without pressing the shutter-release button (smile timer ( A57)). You can use
the skin softening option to smooth the skin tones of human faces.
Display the shooting screen M A (shooting mode) button M F Smart portrait mode M k button
1
Frame the picture.
• Point the camera at a human face.
2
Without pressing the shutter-release button, wait for the subject to smile.
• If the camera detects that the face framed by the double border is smiling, the shutter is automatically released.
• Whenever the camera detects a smiling face, it automatically releases the shutter.
3
End automatic shooting.
• Perform one of the operations listed below to end shooting.
- Set Smile timer to Off.
- Press the A button and select a different shooting mode.
B
Notes About Smart Portrait Mode
Under some shooting conditions, the camera may be unable to detect faces or
detect smiles ( A62). The shutter-release button can also be used for shooting.
C
When the Self-timer Lamp Flashes
When using smile timer, the self-timer lamp flashes when the camera detects a face and flashes quickly immediately after the shutter is released.
Functions Available in Smart Portrait Mode
A (Auto) Mode
Used for general shooting. Settings can be adjusted to suit the shooting conditions and the type of shot you want to capture.
Display the shooting screen M A (shooting mode) button M A (auto) mode M k button
• You can change how the camera selects the area of the frame to focus on by changing the AF area mode setting (
The default setting is Target finding AF (
Functions Available in A (Auto) Mode
45
46
Using Quick Effects
When in A (auto) mode, you can apply effects to images immediately after releasing the shutter.
• The edited image is saved as a separate file with a different name.
1
Press the k button when the image is displayed after it is taken in
A (auto) mode.
Quick effects
• When you press the d button or when no operations are performed for about 5 seconds, the monitor display returns to the shooting screen.
Cancel
• To not display the screen shown on the right, set Quick effects to Off in the shooting menu (
Choose effect
2
Use the multi selector JK to
Quick effects select the desired effect and press the k button.
Pop Super vivid Painting
• Move the zoom control (A2) toward g (i)
to display a confirmation dialog for the
High key Toy camera effect 1
Toy camera applied effect. Move the zoom control toward f (h) to return to the selection
Cancel effect 2 screen for effects.
• To exit without saving the edited image, press the d button. When a confirmation dialog is displayed, select Yes and press the k button.
• See “Quick Effects: Changing Hue or Mood” (E14) for information about
the effect types.
3
Select Yes and press the k button.
Functions That Can Be Set Using the Multi
Selector
The functions that are available vary with the shooting mode, as shown below.
1
2 4
3
Function
1 m
2
3 D
Easy auto w w
-
Scene
*
Special effects w w w
Smart portrait w* w*
-
4 o
Exposure compensation (
w w w
* Availability depends on the setting. See “Default Settings” ( A53) for more
information.
w
A
(auto) w w w
47
48
Using the Flash
You can select the flash mode to match the shooting conditions.
1
Press the multi selector H (m).
2
Select the desired flash mode
( A49) and press the k button.
• If a setting is not applied by pressing the k button within a few seconds, the selection will be canceled.
Auto
40
30
B
The Flash Lamp
• The status of the flash can be confirmed by pressing the shutter-release button halfway.
- On: The flash fires when you press the shutter-release button all the way down.
- Flashing: The flash is charging. The camera cannot shoot images.
- Off: The flash does not fire when an image is taken.
• If the battery level is low, the monitor turns off while the flash is charging.
Available Flash Modes
U Auto
The flash fires when necessary, such as in dim lighting.
• The flash mode icon on the shooting screen is displayed only immediately after the setting is made.
V Auto with red-eye reduction
W
Reduce “red-eye” in portraits caused by the flash.
Off
X
The flash does not fire.
• We recommend using a tripod to stabilize the camera when shooting in dark surroundings.
Fill flash
The flash fires whenever an image is taken. Use to “fill-in” (illuminate) shadows and backlit subjects.
Y Slow sync
Suited to evening and night portraits that include background scenery.
The flash fires when necessary to illuminate the main subject; slow shutter speeds are used to capture background at night or under dim lighting.
C
The Flash Mode Setting
• The setting may not be available with some shooting modes.
• The setting applied in A (auto) mode is saved in the camera’s memory even after the camera is turned off.
C
Auto with Red-eye Reduction
Pre-flashes are fired repeatedly at low intensity before the main flash, reducing the red-eye effect. If the camera detects red-eye while saving an image, the affected area is processed to reduce red-eye before the image is saved.
Note the following when shooting:
• Because pre-flashes are fired, there is a slight lag between when the shutter-release button is pressed and when the image is shot.
• More time than usual is required to save images.
• Red-eye reduction may not produce the desired results in all situations.
• In some rare cases, red-eye reduction may be applied unnecessarily to other areas of the image. In these cases, select another flash mode and take the image again.
49
50
Using the Self-timer
The camera is equipped with a self-timer that releases the shutter about 10 seconds or 2 seconds after you press the shutter-release button. Set Photo VR to Off in the setup menu (
A76) when using a tripod to stabilize the camera
during shooting.
1
Press the multi selector J (n).
2
Select n 10s or n 2s, and press the k button.
Self-timer
• n 10s (10 seconds): Use on important occasions, such as weddings.
• n 2s (2 seconds): Use to prevent camera shake.
• If a setting is not applied by pressing the k button within a few seconds, the selection will be canceled.
• When the shooting mode is Pet portrait scene mode, Y (pet portrait auto release) is displayed (
A40). The self-timer cannot be used.
3
Frame the picture and press the shutter-release button halfway.
• Focus and exposure are set.
4
Press the shutter-release button the rest of the way down.
• Countdown starts. The self-timer lamp flashes and then glows steadily about one second before the shutter is released.
• When the shutter is released, the self-timer is set to k.
• To stop the countdown, press the shutter-release button again.
Using Macro Mode
Use macro mode when taking close-up images.
1
Press the multi selector I (p).
2
Select o and press the k button.
• If a setting is not applied by pressing the k button within a few seconds, the selection will be canceled.
Macro mode
3
Move the zoom control to set the zoom ratio to a position where F and the zoom indicator glow
40 green.
• When the zoom ratio is set to a position where the zoom indicator glows green, the camera can focus on subjects as close as approximately 10 cm
(4 in.) from the lens.
At the wide-angle zoom position from G, the camera can focus on subjects as close as approximately 1 cm (0.4 in.) from the lens.
B
Notes About Using the Flash
The flash may be unable to light the entire subject at distances of less than 50 cm (1 ft 8 in.).
C
The Macro Mode Setting
• The setting may not be available with some shooting modes.
• The setting applied in A (auto) mode is saved in the camera’s memory even after the camera is turned off.
51
52
Adjusting Brightness (Exposure Compensation)
You can adjust overall image brightness.
1
Press the multi selector K (o).
2
Select a compensation value and press the k button.
• To brighten the image, set a positive (+) value.
• To darken the image, set a negative (–) value.
• The compensation value is applied, even without pressing the k button.
Exposure compensation
C
Exposure Compensation Value
• The setting applied in A (auto) mode is saved in the camera’s memory even after the camera is turned off.
• When the shooting mode is Fireworks show (A38) in scene mode, the
exposure compensation cannot be used.
• When the exposure compensation is set while using the flash, the compensation is applied to both the background exposure and to the flash output.
Default Settings
Default settings for each shooting mode are described below.
Shooting mode
Flash
(
G (easy auto)
C (scene)
U 1 b (portrait) c (landscape)
V
W 3 d (sports) W 3
S (night portrait) V 3 f (party/indoor) V 4
Z (beach) z (snow) h (sunset)
U
U
W 3
W 3 i (dusk/dawn)
X (night landscape)
W 3 k (close-up) u (food)
W
W 3
W 3 l (museum) m (fireworks show)
W 3 n (black and white copy)
W
W (backlighting) X 5
/W
5 p (easy panorama)
W 3
O (pet portrait) W 3
C (underwater) W
R (special effects) W
F (smart portrait) U 7
A (auto) U
Self-timer
(
k
Macro
(
k
2
Exposure compensation
(
0.0 k k
3 k 3 k k k k 3 k k 3 k 3 k
3 k
3 k 3 k 3 k
3 k
3 k 3 k 3 o
3 o
3 k k 3 k k k
3 k k k k k k k k k k k 3 k k k 3
Y 6 k k k 8 k
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
3
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
53
54
2
3
4
5
6
7
8
1
The camera automatically selects the flash mode appropriate for the scene it has selected. W (off) can be selected manually.
Cannot be changed. The camera enters macro mode when i is selected.
The setting cannot be changed.
May switch to slow sync with red-eye reduction flash mode.
Flash is fixed at X (fill flash) when HDR is set to k, and is fixed at W (off) when
HDR is set to o.
Self-timer cannot be used. Pet portrait auto release can be turned on or off ( A40).
Cannot be used when Blink proof is set to On or when Smile timer is set to On.
Can be set when Smile timer is set to Off.
Functions That Can Be Set with the
d
Button (Shooting Menu)
The settings listed below can be changed by pressing the d button during
40
30
20
10
0
-10
15m
1010hPa
Image mode
Continuous
ISO sensitivity
AF area mode
Autofocus mode
Quick effects
Available functions vary depending on the shooting mode, as shown below.
Function
Image mode
1
White balance
Continuous
ISO sensitivity
AF area mode
Autofocus mode
Quick effects
Skin softening
Smile timer
Blink proof
–
–
–
–
Easy auto w
–
–
–
–
–
Scene
2
–
–
–
–
–
– w
–
–
–
Special effects w
–
–
–
–
–
–
–
–
–
Smart portrait w
–
–
–
–
–
– w w w
A
(auto) w w w w w w w
–
–
–
1
2
The setting is also applied to other shooting modes.
Additional settings are available for some scene modes. See “Tips and Notes”
55
56
Options Available in the Shooting Menu
Option
Image mode
White balance
Continuous
ISO sensitivity
AF area mode
Autofocus mode
Quick effects
Description
Allows you to set the combination of image size and image quality used when saving images.
• Default setting: P 4608×3456
Allows you to adjust white balance to suit the weather conditions or light source in order to make the colors in images match what you see with your eyes.
• Default setting: Auto
Allows you to select single or continuous shooting.
• Default setting: Single
Allows you to control the camera’s sensitivity to light.
• Default setting: Auto
When Auto is selected, E is displayed in the monitor while shooting if ISO sensitivity increases.
Allows you to determine how the camera selects the focus area that is used for autofocus.
• Default setting: Target finding AF (A61)
Allows you to set the method how the camera focuses.
• Default setting: Pre-focus
Allows you to enable or disable the quick effects
• Default setting: On
A
Option
Skin softening
Smile timer
Blink proof
Description
Allows you to select the skin softening level for human faces.
• Default setting: Normal
Allows you to select whether or not the camera automatically releases the shutter when it detects a human smiling face.
• Default setting: On
The camera automatically releases the shutter twice with every shot and saves one image in which the subject’s eyes are open.
• Default setting: Off
A
57
58
Functions That Cannot Be Used
Simultaneously
Some functions cannot be used with other menu options.
Restricted function
Option Description
Flash mode
Self-timer
Macro mode
Image mode
Continuous
ISO sensitivity
When a setting other than Single is selected, the flash cannot be used.
When Blink proof is set to On, the flash cannot be used.
Smile timer (
When Smile timer is selected, the selftimer cannot be used.
AF area mode (
When Subject tracking is selected, the self-timer cannot be used.
AF area mode (
When Subject tracking is selected, macro mode cannot be used.
Image mode is set as follows depending on the continuous shooting setting:
• Pre-shooting cache: M (image size: 1280 × 960 pixels).
• Continuous H: 120 fps: O
640×480
• Continuous H: 60 fps: M (image size: 1280 × 960 pixels)
• Multi-shot 16: L (image size: 2560
× 1920 pixels)
Self-timer (
If the self-timer is used when Pre-
shooting cache is selected,
Continuous operates using the
Single setting.
When Pre-shooting cache,
Continuous H: 120 fps, Continuous
H: 60 fps, or Multi-shot 16 is selected, the ISO sensitivity setting is automatically specified according to the brightness.
Restricted function
AF area mode
Quick effects
Monitor settings
Print date
Photo VR
Option Description
White balance
Self-timer (
When a setting other than Auto is selected for White balance in Target
finding AF mode, the camera does not detect the main subject.
The quick effects function cannot be used for images with continuous shooting.
When Quick effects is set to On, images are displayed after shooting regardless of the Image review settings.
When Continuous H, Continuous L,
Pre-shooting cache, Continuous H:
120 fps, Continuous H: 60 fps or BSS is selected, date and time cannot be imprinted on images.
When Blink proof is set to On, date and time cannot be imprinted on images.
If the flash fires when On (hybrid) is selected, Photo VR operates using the
On setting.
If the self-timer is used when On
(hybrid) is selected, Photo VR operates using the On setting.
If Continuous is set to any setting other than Single when On (hybrid) is selected, Photo VR operates using the
On setting.
ISO sensitivity (
Motion detection
If ISO sensitivity is set to Fixed range
auto or ISO 400 or higher when On
(hybrid) is selected, Photo VR operates using the On setting.
If Motion detection is set to Auto when
On (hybrid) is selected, Photo VR operates using the On setting.
59
60
Restricted function
Option Description
Motion detection
When the flash fires, Motion
detection is disabled.
When Pre-shooting cache,
Continuous H: 120 fps, Continuous
H: 60 fps or Multi-shot 16 is selected,
Motion detection is disabled.
ISO sensitivity (
When the ISO sensitivity is set to any setting other than Auto, Motion
detection is disabled.
Blink warning
Digital zoom
When a setting other than Single is selected, Blink warning is disabled.
When Multi-shot 16 is selected, digital zoom cannot be used.
AF area mode (
When Subject tracking is selected, digital zoom cannot be used.
Shutter sound
When a setting other than Single is selected, the shutter sound is disabled.
B
Notes About Digital Zoom
• Depending on the shooting mode or the current settings, digital zoom may not be available (
• When digital zoom is in effect, the camera focuses in the center of the frame.
Focusing
The focus area varies depending on the shooting mode.
Using Target Finding AF
When AF area mode ( A56) in A (auto) mode is set to Target finding AF,
the camera focuses in the manner described below.
• When the camera detects the main subject, a yellow border (focus area) is displayed
40
30 around it. If a human face is detected, the camera automatically sets focus priority on it.
When you press the shutter-release button
20
10
0
-10
15m
1010hPa halfway, the focus area that is in focus glows green.
Focus areas
• If no main subject is detected, the camera automatically selects one or more of the 9 focus areas containing the subject closest to the camera when you press the shutterrelease button halfway. When the subject is in focus, the focus areas that are in focus glow green.
1/250 F2.8
Focus areas
B
Notes About Target Finding AF
• Depending on shooting conditions, the subject that the camera determines to be the main subject may vary.
• The main subject may not be detected when using certain White balance settings.
• The camera may not detect the main subject appropriately in the following situations:
- When the subject is very dark or bright
- When the main subject lacks clearly defined colors
- When the shot is framed so that the main subject is at the edge of the monitor
- When the main subject is composed of a repeating pattern
61
62
Using Face Detection
In the following shooting modes, the camera uses face detection to automatically focus on human faces.
• Portrait or Night portrait scene mode
(
• When AF area mode (A56) in A (auto)
mode (
40
30
20
10
0
-10
15m
1010hPa
If the camera detects more than one face, a double border is displayed around the face that the camera focuses on, and single borders are displayed around the other faces.
If the shutter-release button is pressed halfway when no faces are detected:
• In G (easy auto) mode, the focus area changes depending on the scene.
• In Portrait or Night portrait scene mode or smart portrait mode, the camera focuses on the area in the center of the frame.
• In A (auto) mode, the camera selects the focus area containing the subject closest to the camera.
B
Notes About Face Detection
• The camera’s ability to detect faces depends on a variety of factors, including the direction in which the faces are looking.
• The camera may be unable to detect faces in the following situations:
- When faces are partially hidden by sunglasses or otherwise obstructed
- When faces take up too much or too little of the frame
C
Face Detection During Movie Recording
When AF area mode (
A73) in the movie menu is set to Face priority, the camera
focuses on human faces during movie recording. If the b (e movie-record) button is pressed when no faces are detected, the camera focuses on the area in the center of the frame.
Using Skin Softening
When the shutter is released while using one of the shooting modes listed below, the camera detects human faces and processes the image to soften facial skin tones (up to 3 faces).
- The skin softening level can be adjusted.
• Portrait or Night portrait scene mode (A35)
Editing functions such as Skin softening can be applied to saved images by
using Glamour retouch ( A67) even after shooting.
B
Notes About Skin Softening
• It may take more time than usual to save images after shooting.
• Under some shooting conditions, the desired skin softening results may not be achieved, and skin softening may be applied to areas of the image where there are no faces.
Subjects Not Suitable for Autofocus
The camera may not focus as expected in the following situations. In some rare cases, the subject may not be in focus despite the fact that the focus area or the focus indicator glows green:
• Subject is very dark
• Objects of sharply differing brightness are included in the scene (e.g. the sun behind the subject makes that subject appear very dark)
• No contrast between the subject and surroundings (e.g. a portrait subject wearing a white shirt is standing in front of a white wall)
• Several objects are at different distances from the camera (e.g. the subject is inside a cage)
• Subjects with repeating patterns (window blinds, buildings with multiple rows of similarly shaped windows, etc.)
• Subject is moving rapidly
In the situations noted above, try pressing the shutter-release button halfway to refocus several times, or focus on another subject positioned at the same distance from the camera as the actual desired subject, and use focus lock
(
63
64
Focus Lock
Focus lock shooting is recommended when the camera does not activate the focus area that contains the desired subject.
1
Set AF area mode to Center in A (auto) mode (
2
Position the subject in the center of the frame and press the shutter-release button halfway.
• Confirm that the focus area glows green.
• Focus and exposure are locked.
1/250 F2.8
3
Without lifting your finger, recompose the picture.
• Make sure to maintain the same distance between the camera and the subject.
1/250 F2.8
4
Press the shutter-release button the rest of the way down to take the picture.
Playback Features
Playback Zoom
Moving the zoom control toward
g (i) in full-frame playback mode (A30)
zooms in on the image.
Displayed area guide
0004. JPG
15/05/2014 15:30
Full-frame Playback Image is zoomed in.
• You can change the zoom ratio by moving the zoom control toward f (h) or g (i).
• To view a different area of the image, press the multi selector HIJK.
• If you are viewing an image that was captured using face detection or pet detection, the camera zooms in on the face detected at the time of shooting
(except when viewing an image captured in a series). To zoom in on an area of the image where there are no faces, adjust the zoom ratio and then press
HIJK.
• When a zoomed image is displayed, press the k button to return to fullframe playback mode.
C
Cropping Images
When a zoomed image is displayed, you can press the d button to crop the image to include only the visible portion and save it as a separate file (
65
66
Thumbnail Playback, Calendar Display
Moving the zoom control toward
f (h) in full-frame playback mode (A30)
displays images as thumbnails.
Sun
11
4
18
Mon
12
19
26
5 5
2014
Tue Wed
05
Thu
13
6 6
27
14
21
28
7 7
22
29
8 8
1 1
Fri
16
23
30
9 9
2
Sat
10
3
17
2
31
0004. JPG
15/05/2014 15:30
Full-frame Playback Thumbnail Playback Calendar Display
• You can change the number of thumbnails displayed by moving the zoom control toward f (h) or g (i).
• While using thumbnail playback mode, use the multi selector HIJK to select an image, and then press the k button to display that image fullframe.
• While using calendar display mode, use the multi selector HIJK to select a date, and then press the k button to display the images captured on that day.
B
Calendar Display
Images captured when the camera’s date is not set are treated as images captured on January 1, 2014.
Functions That Can Be Set with the
d
Button (Playback Menu)
When viewing images in full-frame playback mode or thumbnail playback mode, you can configure the menu operations listed below by pressing the
0004. JPG
15/05/2014 15:30
Option
Quick retouch*
D-Lighting*
Red-eye correction*
Glamour retouch*
Data imprint*
Print order
Slide show
Protect
Rotate image
Small picture*
Voice memo
Copy
Quick retouch
D-Lighting
Red-eye correction
Glamour retouch
Data imprint
Print order
Slide show
Description
Allows you to rotate the displayed image to portrait or landscape orientation.
Creates a small copy of images.
Allows you to use the camera’s microphone to record voice memos and attach them to images.
Allows you to copy images between the internal memory and a memory card.
A
Allows you to create retouched copies in which contrast and saturation have been enhanced.
Allows you to create copies with enhanced brightness and contrast, brightening dark portions of an image.
Corrects “red-eye” that may occur in images when shooting with a flash.
Detects faces in images and retouches the detected faces glamorously.
Print information, such as altimeter or electronic compass information recorded during shooting, on the images.
Allows you to select which images are printed, and how many copies of each image are printed, prior to printing.
Allows you to view images in an automatic slide show.
Protects selected images from accidental deletion.
67
68
Option
Sequence display options
Choose key picture
Favorite pictures
Remove from favorites
Description
Allows you to select whether to display only the key picture for a sequence of images captured continuously or to display the sequence as individual images.
• When only the key picture is displayed for a sequence, press the k button to display each image in the sequence. Press the multi selector H to return to the key picture display.
Allows you to change the key picture for images captured in sequence.
Allows you to add images to an album.
This option is not displayed in favorite pictures mode.
Allows you to remove images from an album.
This option is displayed only in favorite pictures mode.
A
* Edited images are saved as separate files. Some images may not be edited.
Recording and Playing Back
Movies
Recording Movies
1
Display the shooting screen.
• Check the remaining amount of movie recording time.
• If Photo info in the Monitor settings
(
A76) in the setup menu is set to Movie
frame+auto info, the area that will be visible in the movie can be confirmed before movie recording starts.
40
30
20
10
0
-10
15m
1010hPa
Movie recording time remaining
2
Press the b (e movie-record) button to start movie recording.
• The focus area for autofocus differs depending on the setting of AF area mode
(
The default setting is Face priority.
• Press the multi selector K to pause recording, and press K again to resume recording (except when p iFrame 720/
30p (p iFrame 720/25p) or an HS movie option is selected in Movie options).
Recording automatically ends if it remains paused for about five minutes.
3
Press the b (e movie-record) button again to end recording.
69
70
B
Maximum Movie Length
Individual movie files cannot exceed 4 GB in size or 29 minutes in length, even when there is sufficient free space on the memory card for longer recording.
• The maximum movie length for a single movie is displayed on the shooting screen.
• Recording may end before either limit is reached if camera temperature becomes elevated.
• The actual movie length may vary depending on the movie content, subject movement, or type of memory card.
B
Notes About Saving Images and Recording Movies
The indicator showing the number of exposures remaining or the indicator showing the maximum movie length flashes while images are being saved or while a movie is being recorded. Do not open the battery-chamber/memory card slot cover or
remove the battery or memory card while an indicator is flashing. Doing this could result in loss of data, or in damage to the camera or the memory card.
B
Notes About Movie Recording
• Memory cards with an SD Speed Class rating of 6 or faster are recommended when
recording movies ( F31). Movie recording may stop unexpectedly when memory
cards with a lower Speed Class rating are used.
• When using the camera's internal memory, saving movies may take some time.
• Depending on the file size of a movie, it may not be possible to save the movie in the internal memory or copy it from a memory card to the internal memory.
• There may be some degradation in image quality when digital zoom is used.
• The sounds of zoom control operation, zoom, autofocus lens drive movement, vibration reduction, and aperture operation when brightness changes may be recorded.
• The following phenomena may be seen in the monitor while recording movies.
These phenomena are saved in the recorded movies.
- Banding may occur in images under fluorescent, mercury-vapor, or sodiumvapor lighting.
- Subjects that move quickly from one side of the frame to the other, such as a moving train or car, may appear skewed.
- The entire movie image may be skewed when the camera is panned.
- Lighting or other bright areas may leave residual images when the camera is moved.
• Depending on the distance to the subject or the amount of zoom applied, subjects with repeating patterns (fabrics, lattice windows, etc.) may have colored stripes
(interference patterns, moire, etc.) in them during movie recording and playback.
This occurs when the pattern in the subject and the layout of the image sensor interfere with each other; it is not a malfunction.
B
Notes About Vibration Reduction During Movie Recording
• When Movie VR (A73) in the movie menu is set to On (hybrid), the angle of
view (i.e., the area visible in the frame) becomes narrower during movie recording.
• When using a tripod to stabilize the camera during recording, set Movie VR to Off to prevent potential errors caused by this function.
B
Camera Temperature
• The camera may become warm when shooting movies for an extended period of time or when the camera is used in a hot area.
• If the inside of the camera becomes extremely hot when recording movies, the camera will automatically stop recording.
The amount of time remaining until the camera stops recording (B10s) is displayed.
After the camera stops recording, it turns itself off.
Leave the camera off until the inside of the camera has cooled.
B
Notes About Autofocus
Autofocus may not perform as expected (
A63). Should this occur, try the following:
1. Set AF area mode to Center and Autofocus mode to Single AF (default setting) in the movie menu before starting movie recording.
2. Frame another subject—positioned at the same distance from the camera as the intended subject—in the center of the frame, press the b (e movie-record) button to start recording, and then modify the composition.
71
72
Saving Still Images While Recording Movies
If the shutter-release button is pressed all the way while recording a movie, one frame is saved as a still image. Movie recording continues while the still image is being saved.
• Q is displayed at the top left of the monitor.
When z is displayed, a still image cannot be saved.
• The image size of the still images to be saved is the same as the Movie options (
setting.
B
Notes About Saving Still Images During Movie Recording
• Still images cannot be saved during movie recording in the following situations.
- When movie recording is paused
- When the remaining movie length is less than 5 seconds
- When Movie options is set to Z 1080/60i, U 1080/50i, g 480/30p,
W 480/25p or HS movie
• Frames of a movie that were recorded when a still image was being taken may not be played back in a seamless manner.
• The sounds of operating the shutter-release button when saving a still image may be heard in the recorded movie.
• If the camera moves when the shutter-release button is pressed, the image may be blurred.
Functions That Can Be Set with the d Button
(Movie Menu)
Enter shooting mode M d button M D menu icon M k button
The settings of the menu options listed below can be configured.
Movie options
Open with HS footage
AF area mode
Autofocus mode
Movie VR
Movie light
Wind noise reduction
Option
Movie options
Open with HS footage
AF area mode
Autofocus mode
Movie VR
Movie light
Wind noise reduction
Frame rate
Description
Select the movie type.
Select normal speed to record movies at normal speed, or HS (high speed) to record movies that play in slow or fast motion.
• Default setting: e 1080/30p (S 1080/25p)
Set whether to start recording HS movies or at normal speed when recording HS movies.
• Default setting: On
Set the method how the camera selects the focus area for autofocus during movie recording.
• Default setting: Face priority
Select either Single AF, which locks focus when movie recording begins, or Full-time AF, which continues focusing during movie recording.
• Default setting: Single AF
Select the vibration reduction setting used when recording movies.
• Default setting: On (hybrid)
Set whether or not to enable the movie light that assists recording in dark places during movie recording.
• Default setting: Off
Set whether or not to reduce wind noise during movie recording.
• Default setting: Off
Select the frame rate used when recording movies.
A
73
74
Playing Back Movies
Press the c button to enter playback mode.
Movies are indicated by the movie options icon
(
Press the k button to play back movies.
• To adjust the volume, move the zoom control
(
0010. MOV
15/05/2014 15:30
Movie options
Volume indicator
Functions Available During
Playback
Playback controls are displayed at the bottom of the monitor.
Paused
The operations listed below can be performed by using the multi selector JK to select a control and then pressing the k button.
Function Icon Description
Rewind A Hold down the k button to rewind the movie.
Advance B Hold down the k button to advance the movie.
Pause E
Pause playback. The operations listed below can be performed while paused.
C
Rewind the movie one frame. Hold down the k button for continuous rewinding.
D
Advance the movie one frame. Hold down the k button for continuous advancing.
F Resume playback.
End
I
Extract the desired portion of a movie and save it as a separate file.
H
Extract a single frame of a movie and save it as a still image.
G Return to full-frame playback mode.
Deleting movies
To delete a movie, select the desired movie in full-frame playback mode
(
A30) or thumbnail playback mode (A66) and press the l button (A31).
75
76
General Camera Setup
Functions That Can Be Set with the
d
Button (Setup Menu)
Press the d button M z (setup) menu icon M k button
The settings of the menu options listed below can be configured.
Option
Welcome screen
Welcome screen
Time zone and date
Monitor settings
Print date
Photo VR
Motion detection
AF assist
Description
Allows you to select whether or not the welcome screen is displayed in the monitor when the camera is turned on.
A
Time zone and date
Allows you to set the camera clock.
Monitor settings
Print date
Photo VR
Motion detection
AF assist
Digital zoom
Sound settings
Allows you to adjust photo information display, post-shooting image review, and monitor brightness settings.
Allows you to imprint the shooting date and time on images.
Allows you to select the vibration reduction setting used when shooting still images.
Allows you to set whether or not the camera automatically increases the shutter speed to reduce blurring caused by camera shake if motion is detected when shooting still images.
Allows you to enable or disable the AF-assist illuminator.
Allows you to enable and disable digital zoom.
Allows you to adjust sound settings.
Option Description
Action control response
Playback action control
Map actions
Auto off
Format memory/
Format card
Language
TV settings
Charge by computer
Blink warning
Allows you to set the sensitivity of the operation performed when shaking the camera (action control).
Allows you to set whether or not to enable the image to be selected by shaking the camera in fullframe playback mode.
Allows you to zoom in and out of maps by shaking the camera.
Allows you to set the amount of time that passes before the monitor turns off to save power.
Allows you to format the internal memory or the memory card.
Allows you to change the camera’s display language.
Allows you to adjust TV-connection settings.
Allows you to set whether or not the battery in the camera is charged when the camera is connected to a computer.
Allows you to set whether or not closed eyes are detected when taking images of people using face detection.
Eye-Fi upload
Allows you to set whether or not to enable the function for sending images to a computer using a commercially available Eye-Fi card.
Reset all
Allows you to reset the camera’s settings to their default values.
Firmware version View the current camera firmware version.
A
77
78
Using Location Data Functions/
Displaying Maps
Starting Location Data Recording
This camera receives signals from positioning satellites and obtain its current time and location data.
The obtained location data (latitude and longitude) can be recorded on the images to be shot.
Turn the Location Data Functions On
Press the d button M z (location data options) menu icon M Location data options M k button
Set Time zone and date (
A76) correctly before using the location data
functions.
1
Use the multi selector HI to select Record location data, and then press the k button.
Location data options
Record location data
Update A-GPS file
Erase location data
2
Select On and press the k button.
• Signals are received from the positioning satellites and positioning starts.
Record location data
On
Off
3
Press the d button.
• The camera returns to shooting screen.
• Operate in an open-air area when starting to receive signals from positioning satellites.
B
Notes About Location Data Functions
• Before using the location data functions, read "<Important> Notes About Location
Data Functions (GPS/GLONASS, Electronic Compass)" ( Axviii).
• It takes a few minutes to obtain location data when positioning is performed for the first time or in a situation where positioning cannot be performed for a long period of time, or just after the battery is replaced.
• Positions of the positioning satellites change constantly.
You may not be able to determine the position or it may take some time depending on your location and the time.
To use the location data functions, use the camera in an open-air area with few obstacles in the sky.
Signal receiving will be smoother if the positioning antenna ( A1) is facing the sky.
• The following locations which block or reflect signals may result in failed or inaccurate positioning.
- Inside buildings or underground locations
- Between high-rise buildings
- Under overpasses
- Inside tunnels
- Near high-voltage electrical power lines
- Between clusters of trees
- Underwater
• Using a mobile phone of 1.5 GHz band near this camera may disrupt positioning.
• When carrying this camera around while positioning, do not place it in a metal bag.
Positioning cannot be performed if the camera is covered with metal materials.
• When there is a significant difference in the signals from the positioning satellites, there could be a deviation of up to several hundred meters.
• Be aware of your surroundings when positioning.
• The shooting date and time that is displayed when playing back images is determined by the camera’s internal clock at the time of shooting.
The time obtained by the location data and recorded on images will not be displayed on the camera.
• The location data for the first frame will be recorded on a series of images shot using continuous shooting.
79
80
B
Battery Drain While Recording Location Data and Log Recording
• When Record location data is set to On, record location data functions will continue to operate at the specified interval for approximately 6 hours even after the camera is turned off. Also, record location data functions and log recording will continue to operate while recording logs (
A88) even after the camera is turned
off.
• When Record location data is set to On or while recording logs, the battery power will drain faster than usual. Confirm the battery level especially when recording a log using Start all logs or Start depth log.
C
Location Data Reception Indicator and Points of Interest (POI)
Information
• Location data reception can be checked on the shooting screen.
Location name information
(POI information)
n : Signals are being received from four or more satellites and positioning is being performed. The location data is recorded on the image.
o : Signals are being received from three satellites and positioning is being performed.
The location data is recorded on the image.
40
30
20
10
0
-10
15m
1010hPa
- z: Signals are being received from the satellites, but positioning is not possible. The location data is not recorded on the image.
Location data reception
- y: Signals cannot be received from the satellites, and positioning is not possible.
The location data is not recorded on the image.
• POI information is location name information for the nearest landmarks (facilities) and other details.
- When Display POI in Points of interest (POI) of the Location data options menu (
A87) is set to On, the nearest location name information for the current
position is displayed during shooting.
- When Embed POI is set to On, location name information can be recorded on the image during shooting.
- If the location name information was recorded on the image during shooting, this information is displayed when Display POI is set to On during playback.
• The location name information may not be displayed depending on the setting level in Level of detail of Points of interest (POI). Also, certain landmark names may not be registered, or the landmark name may be different.
C
Underwater Recording of Location Data
While the location data is being obtained, if you select Underwater scene mode, or select G (easy auto) mode and then submerge the camera under water, the screen on the right is displayed.
Select Yes and press the k button. The location data obtained prior to underwater shooting is recorded on the images to be shot underwater.
Underwater
Do you want to use the location data last obtained before submerging?
These data will be recorded with every shot taken until you resurface.
Yes
No
C
Images with Recorded Location Data
• The z icon is displayed during playback for images which have the location data
• The location data recorded on an image can be checked on a map with ViewNX 2 after transferring the image to a computer (
• The actual place of shooting may differ from the location data recorded on the image files due to the accuracy of the location data obtained and a difference in the geodetic system used.
• The location data and POI information recorded on images can be erased using
Erase location data in Location data options ( A87). The erased information
cannot be recovered.
81
82
Displaying Maps
The current position or image shooting location can be displayed on the screen using the camera’s internal map information.
To display the map, press the U (map) button in shooting mode or playback mode.
• Maps cannot be displayed while the camera is being charged with the charging AC adapter.
When Using Shooting Mode
To display the current position on the screen, press the U (map) button in shooting mode when Record location
data in Location data options of the
Location data options menu is set to On.
• To display the current position, the location data must have been obtained.
• To adjust the scale of the map, use the zoom control ( f (h)/g (i)).
Scale
500m
Current position
Current position
Location data reception
• To move the map display, use the multi selector.
• The following operations can be performed when you press the k button.
- Center on current location:
Display the current position at the center of the map.
- Save location: Select a location on the map and save it by pressing the k button.
- Center on saved location: Move the map by selecting a location you have
saved ( A85). You can cancel a location you have saved.
• When the camera lens faces downward, a compass is displayed. A compass is displayed even if Compass display in the location data options is set to
Off.
B
Map Display
• The map display cannot be rotated. Only the north up display (the top of the screen indicates the north) is available.
• The map display scale varies depending on which country is shown on the map.
• In shooting mode, when Record location data in Location data options of the
Location data options menu is set to Off or when positioning could not be performed, a world map centered on the region that was set in Time zone of
Time zone and date in the setup menu (
A76) or a map displayed just before
the current screen is displayed.
C
Notes About Direction and Location Data Display
Direction or location data, etc. is displayed when a map is being displayed in shooting mode or if the U (map) button is held down while the power is off.
1 Date and time 1 5
2 Eye-Fi communication indicator
15/05/2014 15:30
3 Location data reception
1554 m
4 Create log display (location data)
1010 hPa
5 Create log display (altitude/water depth)
6 Altitude
NNE
24º 19’ 21”
124º 04’ 37”
7 Atmospheric pressure
N
E
8 Direction
9 Latitude and longitude
10 Location name information (Points of
Interest: POI)*
11 Compass display
11
6
7
8
9
10
* “----” may be displayed for the location name information depending on the setting level in Level of detail of Points of interest (POI).
83
84
When Using Playback Mode
If an image displaying z in the full-frame display is selected and the U (map) button is pressed, the image shooting location is displayed on the screen.
• To display the map and the image shooting location, the location data must have been recorded on playback image.
• To adjust the scale of the map, use the zoom control ( f (h)/g (i)).
Scale
500m
Location name
• To move the map display, use the multi selector.
500m 500m
Map display Map display
(Selecting a thumbnail image)
• When the k button is pressed, another image can be selected. Only images with the recorded location data are displayed in the thumbnail display.
• The following operations can be performed when you press the k button while thumbnails are displayed.
- Scroll map: Return to the map display screen
- Altitude/depth logs: Display the altitude log or water depth log graph (
you play back images shot while the altitude log or water depth log was recorded using
- Save location: Save the shooting location of the image displayed as a location.
m / time
100
80
60
40
20
0
0 10 20 30 40 depth log
Graph display
50
Altitude log or water
60
- Center on saved location: Move the map by selecting a location you have saved
( A85). You can cancel a location you have saved.
• The image shooting location and a rough direction are indicated by C on the map (C
Image shooting location and direction indicates north), and the selected image is
500m highlighted in yellow.
• Press the multi selector JK to select the image.
• Operate the zoom control toward g (i) to enlarge the image. Operate the zoom control toward f (h) to return to the map display.
Thumbnail display
C
Notes About Saving Locations
You can save up to 30 locations.
• When you select Center on saved location, the map scrolls to the closest saved location from the center of the screen.
• Use the multi selector HIJK to move to other saved locations.
• Press the l button to cancel a location.
• When you press the k button, the monitor display returns to the previous screen.
MAP
85
86
Using Altimeter and Depth Gauge
You can display the altitude or water depth and the atmospheric pressure of the current position on the screen and record the displayed value on the images to be shot.
• Use Alt./depth correction in the Location data options menu to correct the data in advance. Before using the camera underwater, make sure to adjust the data to 0 m at the surface of water. You can display a more accurate altitude or water depth if you adjust the data frequently. When altitude or water depth is corrected, i is displayed next to the altitude or water depth.
• The altitude or water depth, and the atmospheric pressure are always
Altimeter or depth gauge displayed.
• The altimeter or depth gauge is displayed when the Altimeter/depth
gauge setting of Altitude/depth
options in the Location data options menu (
setting).
• The depth gauge and water depth are displayed when you select
Underwater scene mode, or select G
40
30
20
10 pressure
0
-10
15m
1010hPa
Atmospheric
Altitude or water
(easy auto) mode and then submerge the camera under water.
• The display range of the altimeter and altitude is -300 m to +4500 m (-984 to depth
+14,760 ft).
• The display range of the depth gauge and water depth is 0 m to 20 m (0 ft to
65 ft).
B
Notes About Altimeter and Depth Gauge
• Do not use the altimeter or depth gauge in this camera for specialized applications such as mountain climbing or underwater diving. The displayed information is intended as a general guide only.
• Since the altitude is measured using the camera's internal barometer, the data may not be displayed correctly in some climate conditions.
• When Altimeter/depth gauge is set to On, the altimeter or depth gauge and the atmospheric pressure are displayed even if Hide info is selected for Photo info in
Monitor settings of the setup menu (
• If the camera is not being used for underwater shooting when Underwater scene mode is selected, the depth gauge display is fixed at 0 m (0 ft).
• When the water depth exceeds 15 m (49 ft), the depth gauge display turns orange.
When water depth exceeds 18 m (59 ft), the depth gauge display turns red.
C
Altitude Log and Water Depth Log
When Create log in the Location data options menu is selected, altitude or water depth information can be recorded at regular intervals.
• If you select Start all logs, the log recording of location, altitude, and water depth information starts.
• If you select Start depth log and submerge the camera under water, only the log recording of water depth starts.
You can display the recorded logs as graphs by using View log.
C
More Information
A67, E18) to imprint information such as altitude and
direction measured by electronic compass on images.
Functions That Can Be Set Using the d Button
(Location Data Options Menu)
Press the d button Mz (location data options) menu icon M k button
The settings of the menu options listed below can be configured.
• The Location data options menu can be displayed also by pressing the d button while the map is displayed.
Location data options
Distance units
Calculate distance
Points of interest (POI)
Create log
View log
Set clock from satellite
Option
Location data options
Distance units
Calculate distance
Description A
Allows you to enable location data functions. To update the A-GPS file, access the website below.
http://nikonimglib.com/agps3/
• Default setting:
- Record location data: Off
Allows you to set the distance units of the map display.
• Default setting: km (m)
Allows you to calculate the linear distance from the current position to the shooting location of the image or between image shooting locations.
87
88
Points of interest
(POI)
Option
Create log
View log
Description A
Allows you to make the settings for the POI (points of interest, location name information).
• Default setting:
- Embed POI: Off
- Display POI: Off
- Level of detail: Level 6 (detailed)
Allows you to make the settings to create a log of location, altitude, and water depth information.
You can delete the log data or save it to memory card.
• Default setting:
- Start all logs M Log interval: 15 s, Start
log: Log data for next 24 hrs
- Start location log M Log interval: 15 s,
Start log: Log data for next 24 hrs
- Start depth log M Log interval: 1 min
Allows you to check or erase the log data saved on a memory card.
Set clock from satellite
Electronic compass
Altitude/depth options
Allows you to set the date and time of the camera's internal clock using signals from the positioning satellites.
Allows you to set whether or not to display the electronic compass.
You can display the electronic compass and calibrate it if it is not displaying the correct directions.
• Default setting:
- Compass display: Off
Allows you to set whether to display the altimeter or depth gauge.
You can display the altimeter and depth gauge and calibrate them if they are not displaying the correct directions.
• Default setting:
- Altimeter/depth gauge: On
- Altitude/depth units: m
Using the Wi-Fi (Wireless LAN)
Function
Functions That Can Be Performed Using
Wi-Fi
You can perform the following functions if you install the dedicated software
“Wireless Mobile Utility” on your smart device that runs on Android OS or iOS, and connect it to the camera.
Take Photos
You can take still images using the two methods described below.
• Release the shutter on the camera and save the captured images to a smart device.
• Use a smart device to remotely* release the camera shutter and save images to the smart device.
*Operations cannot be performed on the camera during remote control operation.
View Photos
You can copy the images saved in the camera’s memory card and view them on your smart device.
Installing the Software on the Smart Device
1
Use your smart device to connect to Google Play Store,
App Store or other online apps marketplace and search for
“Wireless Mobile Utility.”
• Check the user’s manual provided with your smart device for further details.
2
Check the description and other information and install the software.
• For more information about how to operate the software, download the user’s manual from the website below.
- Android OS: http://nikonimglib.com/ManDL/WMAU/
- iOS: http://nikonimglib.com/ManDL/WMAU-ios/
89
90
Connecting the Smart Device to the
Camera
Press the d button M q menu icon M k button
1
Use the multi selector HI to select Connect to smart device and press the k button.
• If Connect to smart device cannot be
selected, see "Notes About Wi-Fi
• When the Wi-Fi function is turned on, the
SSID and password of the camera are displayed.
• If no connection confirmation is received from the smart device within 3 minutes, the message “No access.” is displayed and the camera returns to the Wi-Fi options screen.
Connect to smart device
Disable Wi-Fi
Options
Current settings
Restore default settings
Connect to smart device
SSID:
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
Password:
XXXXXXXXXXXXXXXXXX
Back Cancel
2
Set the Wi-Fi setting on the smart device to On.
• Check the user’s manual provided with your smart device for further details.
• After the network name (SSID) that can be used for the smart device is displayed, select the SSID displayed on the camera.
• When the message for entering a password is displayed, enter the password that is displayed on the camera.
• When the camera is successfully connected to a Wi-Fi network, the shooting screen is displayed on the camera with the Wi-Fi communication indicator
(
3
Start "Wireless Mobile Utility" installed on the smart device.
• The screen for selecting “Take photos” or “View photos” is displayed.
• When the message “Cannot connect to camera.” is displayed, return to step
1 and retry the procedure.
To Terminate the Wi-Fi Connection
Perform one of the following operations.
• Turn off the camera.
• Select Disable Wi-Fi in the Wi-Fi options menu on the camera (except when the camera is operated by remote control).
• Set the Wi-Fi setting on the smart device to Off.
B
Notes About Wi-Fi Connection
• Connect to smart device cannot be selected in the following situations:
- When no memory card is inserted in the camera.
- When an Eye-Fi card (
E77) is inserted in the camera.
- When the camera is connected to a TV, computer, or printer.
- When the battery level indicator in the monitor indicates B. In addition, if B is indicated when Wi-Fi is connected, the connection is terminated.
• Select Disable Wi-Fi in a place where the use of radio waves is prohibited.
• When Wi-Fi is connected, Auto off is disabled.
• When Wi-Fi is connected, the battery drains faster than normal.
C
Notes About Security Settings
If the camera is installed with the Wi-Fi function without proper security settings
(encryption and password), unauthorized third parties may access the network and cause harm. We strongly recommend performing the required security settings before using the Wi-Fi function.
Use Options of the Wi-Fi options menu ( E92) to perform the security settings.
91
92
Connecting the Camera to a TV,
Computer, or Printer
Connection Methods
You can enhance your enjoyment of images and movies by connecting the camera to a TV, computer, or printer.
HDMI micro connector
(Type D)
Micro-USB connector
How to open the batterychamber/memory card
Insert the plug straight.
• Before connecting the camera to an external device, make sure the remaining battery level is sufficient and turn the camera off. Before disconnecting, make sure to turn the camera off.
• If the AC Adapter EH-62F (available separately) is used, this camera can be powered from an electrical outlet. Do not use any other make or model of
AC adapter as it may cause the camera to heat up or malfunction.
• For information about the connection methods and subsequent operations, refer to the documentation included with the device in addition to this document.
Viewing images on a TV
Images and movies captured with the camera can be viewed on a TV.
Connection method: Connect a commercially available HDMI cable to the TV’s HDMI input jack.
Viewing and organizing images on a computer
Printing images without using a computer
You can transfer images to a computer to perform simple retouching and manage image data.
Connection method: Connect the camera to the computer’s
USB port with the USB cable.
• Before connecting to a computer, install ViewNX 2 on the computer (
• If any USB devices that draw the power from the computer are connected, disconnect them from the computer before you connect the camera to it. Connecting the camera and other USB-powered devices to the same computer simultaneously may cause a camera malfunction or excessive power supply from the computer, which could damage the camera or memory card.
If you connect the camera to a PictBridge-compatible printer, you can print images without using a computer.
Connection method: Connect the camera directly to the printer’s USB port with the USB cable.
93
94
Using ViewNX 2
Install ViewNX 2 to upload, view, edit, and share photos and movies.
Your Imaging Toolbox ViewNX 2™
Installing ViewNX 2
An Internet connection is required. For system requirements and other information, see the Nikon website for your region.
1
Download the ViewNX 2 installer.
Start the computer and download the installer from: http://nikonimglib.com/nvnx/
2
Double-click the downloaded file.
3
Follow the on-screen instructions.
4
Exit the installer.
Click Yes (Windows) or OK (Mac).
Transferring Images to the Computer
1
Choose how images will be copied to the computer.
Choose one of the following methods:
• Direct USB connection: Turn the camera off and ensure that the memory card is inserted in the camera. Connect the camera to the computer using the USB cable. The camera automatically turns on.
To transfer images that are saved in the camera’s internal memory, remove the memory card from the camera before connecting it to the computer.
• SD card slot: If your computer is equipped with an SD card slot, the card can be inserted directly in the slot.
• SD card reader: Connect a card reader (available separately from third-party suppliers) to the computer and insert the memory card.
If a message is displayed prompting you to choose a program, select Nikon
Transfer 2.
• When using Windows 7
If the dialog shown at right is displayed, follow the steps below to select Nikon Transfer
2.
1 Under Import pictures
and videos, click Change
program. A program selection dialog will be displayed; select Import File using Nikon Transfer 2 and click OK.
2 Double-click Import File.
If the memory card contains a large number of images, it may take a while for
Nikon Transfer 2 to start. Wait until Nikon Transfer 2 starts.
B
Connecting the USB Cable
The connection may not be recognized if the camera is connected to the computer via a USB hub.
95
96
2
Transfer images to the computer.
• Click Start Transfer.
Start Transfer
• At default settings, all the images on the memory card will be copied to the computer.
3
Terminate the connection.
• If the camera is connected to the computer, turn the camera off and disconnect the USB cable.
• If you are using a card reader or card slot, choose the appropriate option in the computer operating system to eject the removable disk corresponding to the memory card and then remove the card from the card reader or card slot.
Viewing Images
Start ViewNX 2.
• Images are displayed in ViewNX 2 when transfer is complete.
• Consult online help for more information on using ViewNX 2.
C
Starting ViewNX 2 Manually
• Windows: Double-click the ViewNX 2 shortcut on the desktop.
• Mac: Click the ViewNX 2 icon in the Dock.
97
98
Reference Section
The Reference Section provides detailed information and hints about using the camera.
Shooting
Using Easy Panorama (Shooting and Playback)......................
Playback
Favorite Pictures Mode.....................................................................
Auto Sort Mode...................................................................................
List by Date Mode ............................................................................
Viewing and Deleting Images Captured Continuously
Editing Still Images ..........................................................................
Connecting the Camera to a TV (Viewing Images on a TV)....
Connecting the Camera to a Printer (Direct Print) ...............
Editing Movies ...................................................................................
Menu
The Shooting Menu (for A (Auto) Mode)..............................E30
The Smart Portrait Menu................................................................
The Playback Menu..........................................................................
The Movie Menu ...............................................................................
The Setup Menu................................................................................
The Location Data Options Menu ............................................. E79
The Wi-Fi Options Menu ................................................................
Additional Information
Error Messages ..................................................................................
Optional Accessories....................................................................
E 1
E 2
Using Easy Panorama (Shooting and
Playback)
Shooting with Easy Panorama
Enter shooting mode M A (shooting mode) button Mb (second icon from the top*) M K M HI M p Easy panorama M k button
* The icon of the last scene selected is displayed.
1
Select W Normal (180°) or X
Wide (360°) as the shooting range
and press the k button.
• When the camera is readied in the horizontal position, the image size (width × height) is as follows.
- W Normal (180°):
4800 × 920 when moved horizontally
1536 × 4800 when moved vertically
- X Wide (360°):
9600 × 920 when moved horizontally
1536 × 9600 when moved vertically
2
Frame the first edge of the panorama scene, and then press the shutter-release button halfway to focus.
• The zoom position is fixed at wide-angle position.
• The camera focuses on the area in the center of the frame.
3
Press the shutter-release button all the way, and then remove your finger from the shutter-release button.
• KLJI are displayed to indicate the direction of camera movement.
40
30
20
10
0
-10
15m
1010hPa
Normal (180°)
4
Move the camera in one of the four directions until the guide indicator reaches the end.
• When the camera detects which direction it is moving in, shooting begins.
Guide
Example of camera movement
• Using your body as the axis of rotation, move the camera slowly in an arc, in the direction of the marking (KLJI).
• Shooting stops if the guide does not reach the edge within about 15 seconds (when W Normal (180°) is selected) or within about 30 seconds (when X Wide (360°) is selected) after shooting starts.
B
Notes About Easy Panorama Shooting
• The range of the image seen in the saved image is narrower than that seen in the monitor at the time of shooting.
• If the camera is moved too quickly or shaken too much, or if the subject is too uniform (e.g. walls or darkness), an error may occur.
• If shooting is stopped before the camera reaches the half-way point in the panorama range, a panorama image is not saved.
• If more than half of the panorama range is captured but shooting ends before reaching the edge of the range, the range not captured is recorded and displayed in gray.
E 3
E 4
Viewing Images Captured with Easy Panorama
Switch to playback mode (
image captured using easy panorama in fullframe playback mode, and then press the k button to scroll the image in the direction that was used when shooting.
0004. JPG
15/05/2014 15:30
Playback controls are displayed at the bottom of the monitor during playback.
Use the multi selector JK to select a control, and then press the k button to perform the following operations.
Function
Rewind
Advance
Pause
End
Icon Description
A Hold down the k button to scroll backward quickly.
B Hold down the k button to scroll forward quickly.
E
Pause playback. The operations listed below can be performed while paused.
C Hold down the k button to rewind.
D Hold down the k button to scroll.
F Resume automatic scrolling.
G Switch to full-frame playback mode.
B
Notes About Scroll Playback
This camera may not be able to scroll the playback of, or zoom in on, easy panorama images captured with another make or model of digital camera.
Favorite Pictures Mode
By adding images (except movies) to albums as favorite pictures, you can play back only the added images.
• Images can be sorted into nine albums. Up to 200 images can be added to each album.
• The original images are not copied or moved.
• The same image can be added to multiple albums.
Adding Images to Albums
Press the c button (playback mode*) M d button M c , F or C menu icon M Favorite pictures M k button
* Images cannot be added in favorite pictures playback mode.
1
Use the multi selector JK to select an image and use H to display L.
• You can add L to multiple images. To remove L, press I.
• Move the zoom control (A2) toward g (i)
to switch to full-frame playback or f (h) to switch to thumbnail playback.
Favorite pictures
Back
2
Press the k button after configuring the settings.
3
Select the desired album and press the k button.
• The selected images are added.
Favorite pictures
Back Add
E 5
E 6
Playing Back Images in Albums
Press the c button (playback mode) M c button M h Favorite pictures M k button
Use the multi selector to select an album and then press the k button to play back the images in the selected album.
• Functions in the playback menu (A67) can
be used for the images in the selected album
Favorite pictures
(except Copy and Favorite pictures).
• The following operations are available from the album selection screen.
Choose icon
d button: Changes the album icon
l button: Deletes all original images added to the selected album.
B
Notes About Deletion
If an image is deleted while using favorite pictures mode, the original image is
deleted. When removing images from albums, see “Removing Images from Albums”
Removing Images from Albums
Enter favorite pictures mode M select the album containing the image you want to remove M k button M d button M Remove from favorites M k button
1
Use the multi selector JK to select an image and use H to hide
L.
• To display the icons again, press I.
• Move the zoom control (A2) toward g (i)
to switch to full-frame playback or f (h) to switch to thumbnail playback.
Remove from favorites
Back
2
Press the k button after configuring the settings.
3
Select Yes and press the k button.
• To cancel removal, select No.
E 7
E 8
Changing the Favorites Album Icon
Press the c button (playback mode) M c button M h Favorite pictures M k button
1
Use the multi selector to select an album and press the d button.
Favorite pictures
2
Use JK to select an icon color and press the k button.
Choose icon
Choose icon
3
Select an icon and press the k button.
• The icon changes.
Back
Choose icon
Back
Auto Sort Mode
Images are automatically sorted into categories, such as portraits, landscapes, and movies, based on the camera settings at the time of shooting.
Press the c button (playback mode) M c button M F Auto sort M k button
Use the multi selector to select a category and then press the k button to play back the images in the selected category.
• Functions in the playback menu (A67) can
be used for the images in the selected category (except Copy and Remove from
favorites).
• While the category selection screen is displayed, press the l button to delete all original images in the selected category.
Portraits
Other scenes
B
Notes About Auto Sort Mode
• Up to 999 images and movie files can be sorted into each category in auto sort mode.
• Images or movies saved by cameras other than this camera cannot be played back in auto sort mode.
E 9
List by Date Mode
Press the c button (playback mode) M c button M C List by date M k button
Use the multi selector to select a date and then press the k button to play back the images captured on the selected date.
• Functions in the playback menu (A67) can
be used for the images in the selected shooting date (except Copy and Remove
from favorites).
• The following operations are available while the shooting date selection screen is
List by date
20/05/2014
15/05/2014
10/05/2014
05/05/2014
3
2
1
10 displayed.
d button: The functions listed below are available.
• Print order*
• Slide show
• Protect*
* The same settings can be applied to all images captured on the selected date.
l button: Deletes all images captured on the selected date.
B
Notes About List by Date Mode
• Up to the most recent 29 dates can be selected. If images exist for more than 29 dates, all images saved earlier than the most recent 29 dates will be combined under Others.
• The 9,000 most recent images can be displayed.
• Images captured when the camera’s date is not set are treated as images captured on January 1, 2014.
E 10
Viewing and Deleting Images Captured
Continuously (Sequence)
Viewing Images in a Sequence
Images captured continuously are saved as a sequence.
The first image of a sequence is used as the key picture to represent the sequence when displayed in full-frame playback mode or thumbnail playback mode (default setting).
To display each image in the sequence individually, press the k button.
0004. JPG
15/05/2014 15:30
After pressing the k button, the operations listed below are available.
• To display the previous or next image, press the multi selector JK.
• To display images that are not included in the sequence, press H to return to the key picture display.
• To display images in a sequence as thumbnails, or to play them back in a slide
Back show, set Sequence display options to Individual pictures in the playback menu (
B
Sequence Display Options
Images captured continuously with cameras other than this camera cannot be displayed as a sequence.
C
Playback Menu Options Available When Using Sequence
• When images in a sequence are displayed in full-frame playback mode, press the
d button to select functions in playback menu (A67).
• If you press the d button when a key picture is displayed, the following settings can be applied to all images in the sequence:
- Favorite pictures, Print order, Protect, Copy
E 11
Deleting Images in a Sequence
When the l button is pressed for images in a sequence, the images that are deleted vary depending on how the sequences are displayed.
• When the key picture is displayed:
- Current image: All images in the displayed sequence are deleted.
- Erase selected
images:
- All images:
When a key picture is selected on the erase
selected images screen ( A32), all images in
that sequence are deleted.
All images in the internal memory or on the memory card are deleted.
• When images in a sequence are displayed in full-frame playback mode:
- Current image:
- Erase selected
images:
- Entire sequence:
The image currently displayed is deleted.
Images that are selected in the sequence are deleted.
All images in the displayed sequence are deleted.
E 12
Editing Still Images
Before Editing Images
You can easily edit images on this camera. Edited copies are saved as separate files.
Edited copies are saved with the same shooting date and time as the original.
C
Restrictions on Image Editing
An image can be edited up to ten times.
E 13
Quick Effects: Changing Hue or Mood
Quick effects option
Pop and Super vivid
Painting, High key, Toy camera effect
1, Toy camera effect 2, Low key, Cross process (red), Cross process (yellow),
Cross process (green), and Cross process (blue)
Soft, Soft portrait, Fisheye, Cross screen, and Miniature effect
Description
Mainly enhances the color saturation.
Mainly adjusts hue and creates a different look for the image.
High-contrast monochrome, Sepia,
Cyanotype, and Selective color
Fog removal
Processes images with a variety of effects.
Turns multicolor images into single color images. Selective color transforms all colors, except a specified color, to black and white.
Reduce blurring of images caused by underwater shooting.
1
Display the image to which you want to apply an effect in fullframe playback mode and press the k button.
0004. JPG
15/05/2014 15:30
2
Use the multi selector JK to
Quick effects select the desired effect and press the k button.
Pop Super vivid
• Move the zoom control (A2) toward g (i)
to display a confirmation dialog for the applied effect. Move the zoom control toward f (h) to return to the selection
High key
Cancel
Toy camera effect 1 screen for effects.
• To exit without saving the edited image, press the d button.
3
Select Yes and press the k button.
• An edited copy is created.
Painting
Toy camera effect 2
E 14
Quick Retouch: Enhancing Contrast and Saturation
Press the c button (playback mode) M select an image M d button
M Quick retouch M k button
Use the multi selector HI to select the amount of effect applied and press the k button.
• The edited version is displayed on the right.
• To exit without saving the copy, press J.
Quick retouch
Normal
Amount
D-Lighting: Enhancing Brightness and Contrast
Press the c button (playback mode) M select an image M d button
M D-Lighting M k button
Use the multi selector HI to select
OK and press the
k button.
• The edited version is displayed on the right.
• To exit without saving the copy, select Cancel and press the k button.
D-Lighting
OK
Cancel
E 15
Red-eye Correction: Correcting Red-eye When
Shooting with the Flash
Press the c button (playback mode) M select an image M d button
M Red-eye correction M k button
Preview the result and press the k button.
• To exit without saving the copy, press the multi selector J.
Red-eye correction
Back Save
B
Notes About Red-eye Correction
• Red-eye correction can only be applied to images when red-eye is detected.
• Red-eye correction can be applied to pets (dogs or cats) even if their eyes are not red.
• Red-eye correction may not produce the desired results in some images.
• In some rare cases, red-eye correction may be applied unnecessarily to other areas of the image.
E 16
Glamour Retouch: Enhancing Human Faces
Press the c button (playback mode) M select an image M d button
M Glamour retouch M k button
1
Use the multi selector HIJK to select the face that you want to retouch and press the k button.
• When only one face is detected, proceed to step 2.
Subject selection
Back
2
Use JK to select the effect, use
HI to select the effect level, and press the k button.
• You can simultaneously apply multiple effects.
Adjust or check the settings for all effects before pressing the k button.
F (small face), B (skin softening), C
Skin softening
Back
(powder), m (glare reduction), E (hide eye bags), A (big eyes), G
(whiten eyes), n (eye shadow), o (mascara), H (whiten teeth), p
(lipstick), D (redden cheeks)
• Press the d button to return to the screen for selecting a face.
3
Preview the result and press the k button.
• To change the settings, press J to return to step 2.
• To exit without saving the edited image, press the d button.
Preview
3
2
1
Save
4
Select Yes and press the k button.
• An edited copy is created.
Save OK?
Yes
No
E 17
B
Notes About Glamour Retouch
• Only one face per image can be edited using the glamour retouch function. You can retouch up to ten people (ten times) if you continue choosing different faces to retouch from the edited copy you created.
• Depending upon the direction in which faces are looking, or the brightness of faces, the camera may be unable to accurately detect faces, or the glamour retouch function may not perform as expected.
• If no faces are detected, a warning is displayed and the screen returns to the playback menu.
• The glamour retouch function is available only for images captured when the ISO sensitivity is 1600 or lower.
Data Imprint: Imprinting Information such as
Altitude and Direction Measured by the Electronic
Compass on Images
c button (playback mode) M select an image M d button M Data imprint M k button
Use the multi selector HI to select
OK and press the
k button.
Data imprint
• The information to be imprinted on images includes the altitude or water depth,
NNE
15/05/2014 15:30
15m 1010hPa
N31° 23” 15’ E136° 15” 32’ atmospheric pressure, direction measured by the electronic compass, date/time, and
OK
Cancel latitude and longitude recorded on images
(
• To exit without saving the copy, select Cancel and press the k button.
B
Notes About Data imprint
• Only the information recorded on images is imprinted on the images.
• The information may not be displayed properly if the image size is small.
E 18
Small Picture: Reducing the Size of an Image
Press the c button (playback mode) M select an image M d button
M Small picture M k button
1
Use the multi selector HI to select the desired copy size and press the k button.
• Images taken at an image mode setting of l 4608×2592 are saved at 640 × 360 pixels. Proceed to step 2.
2
Select Yes and press the k button.
• An edited copy is created (compression ratio of approximately 1:8).
Small picture
640×480
320×240
160×120
Create small picture file?
Yes
No
B
Notes About Small Picture
Images at a 1:1 aspect ratio cannot be edited.
E 19
Crop: Creating a Cropped Copy
1
Move the zoom control to enlarge the image (
2
Refine copy composition and press the d button.
• Move the zoom control toward g (i) or f (h) to adjust the zoom ratio. Set a zoom ratio at which u is displayed.
• Use the multi selector HIJK to scroll the image so that only the portion to be copied is visible in the monitor.
3
Select Yes and press the k button.
• An edited copy is created.
Save this image as displayed?
Yes
No
C
Image Size
When the image size of the cropped copy is 320 × 240 or smaller, the image is displayed at a smaller size during playback.
C
Cropping the Image in Its Current “Tall” Orientation
Use the Rotate image option ( E50) to rotate the image so that it is displayed in
landscape orientation. After cropping the image, rotate the cropped image back to
“tall” orientation.
E 20
Connecting the Camera to a TV (Viewing
Images on a TV)
1
Turn off the camera and connect it to the TV.
• Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them.
To the HDMI input connector
HDMI micro connector
(Type D)
2
Set the TV’s input to external input.
• See the documentation provided with your TV for details.
3
Hold down the c button to turn on the camera.
• Images are displayed on the TV.
• The camera monitor does not turn on.
C
Using a TV Remote Control (HDMI Device Control)
The remote control of an HDMI-CEC-compatible TV can be used to select images, start and pause movie playback, switch between full-screen playback mode and four-image thumbnail display, etc.
• Set the HDMI device control setting (E74) of TV settings to On (default
setting) and then connect the camera and TV using an HDMI cable.
• Aim the remote control at the TV when operating it.
E 21
Connecting the Camera to a Printer (Direct
Print)
Users of PictBridge-compatible printers can connect the camera directly to the printer and print images without using a computer.
Take images
Select images for printing and number of copies using
Print order option (
Connect to the printer (
Print images one at a time
Print multiple images
(
When printing is complete, turn the camera off and disconnect the USB cable
E 22
Connecting the Camera to a Printer
1
Turn off the camera.
2
Turn on the printer.
• Check printer settings.
3
Connect the camera to the printer using the USB cable.
• Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them.
4
The camera is automatically turned on.
• The PictBridge startup screen (1) is displayed in the camera monitor, followed by the Print selection screen ( 2).
1 2
Print selection
15/05/2014 No. 32 32
B
If the PictBridge Startup Screen Is not Displayed
When Auto is selected for Charge by computer (
print images with direct connection of the camera to some printers. If the PictBridge startup screen is not displayed after the camera is turned on, turn the camera off and disconnect the USB cable. Set Charge by computer to Off and reconnect the camera to the printer.
E 23
Printing Individual Images
1
Use the multi selector to select the desired image and press the k button.
• Move the zoom control toward f (h) to switch to thumbnail playback or g (i) to switch to full-frame playback.
2
Use HI to select Copies and press the k button.
3
Select the desired number of copies (up to 9) and press the k button.
Print selection
15/05/2014 No. 32 32
PictBridge
1 prints
Start print
Copies
Paper size
Copies
4
E 24
4
Select Paper size and press the k button.
5
Select the desired paper size and press the k button.
• To apply the paper size setting configured on the printer, select Default as the paper size option.
• The paper size options available on the camera vary depending on the printer that you use.
6
Select Start print and press the k button.
• Printing starts.
• To cancel printing, press the k button.
PictBridge
4 prints
Start print
Copies
Paper size
Paper size
Default
3.5×5 in.
5×7 in.
100×150 mm
4×6 in.
8×10 in.
Letter
PictBridge
4 prints
Start print
Copies
Paper size
E 25
Printing Multiple Images
1
When the Print selection screen is displayed, press the d button.
Print selection
15/05/2014 No. 32 32
2
Use the multi selector HI to select Paper size and press the k button.
• To exit the print menu, press the d button.
3
Select the desired paper size and press the k button.
• To apply the paper size setting configured on the printer, select Default in the paper size option.
• The paper size options available on the camera vary depending on the printer that you use.
4
Select Print selection, Print all
images, or DPOF printing and
press the k button.
Print menu
Print selection
Print all images
DPOF printing
Paper size
Paper size
Default
3.5×5 in.
5×7 in.
100×150 mm
4×6 in.
8×10 in.
Letter
Print menu
Print selection
Print all images
DPOF printing
Paper size
E 26
Print selection
Select images (up to 99) and the number of copies (up to 9) of each.
• Use the multi selector JK to select images, and use HI to specify the
Print selection 10
Back
1 1 number of copies to be printed.
• Images selected for printing are indicated by M and the numeral indicating the number of copies to be printed. If no copies have been specified for images, the selection is canceled.
• Move the zoom control toward g (i) to switch to full-frame playback or f (h) to switch to thumbnail playback.
• Press the k button when setting is complete.
• When the screen shown on the right is displayed, select Start print and press the k button to start printing.
Print selection
10 prints
3
Start print
Cancel
Print all images
One copy each of all images saved in the internal memory, or on the memory card, is printed.
• When the screen shown on the right is displayed, select Start print and press the k button to start printing.
Print all images
18 prints
Start print
Cancel
DPOF printing
Print images for which a print order was created using the Print order option
(
• When the screen shown on the right is displayed, select Start print and press the k button to start printing.
To view the current print order, select
View images and press the k button.
To print images, press the k button again.
DPOF printing
10 prints
Start print
View images
Cancel
E 27
Editing Movies
Extracting Only the Desired Portion of a Movie
The desired portions of a recorded movie can be saved as a separate file.
1
Play back the desired movie and pause at the start point of the portion that is to be extracted (
2
Use the multi selector JK to select I in the playback controls, and then press the k button.
3
Use HI to select M (Choose start point) in the editing controls.
• Use the multi selector JK to move the start point.
• To cancel editing, select O (Back), and press the k button.
4
Use HI to select N (Choose end point).
• Use the multi selector JK to move the end point.
• To preview the specified portion, select G and then press the k button. Press the k button again to stop previewing.
5
Use HI to select m (Save) and press the k button.
• Follow the instructions on the screen to save the movie.
Choose start point
Choose end point
Save
E 28
B
Notes About Movie Editing
• Use a sufficiently charged battery to prevent the camera from turning off during editing.
• A movie that was created by editing cannot be trimmed again.
• The actual trimmed portion of a movie may differ slightly from the portion selected using the start and end points.
• Movies cannot be trimmed so that they are less than two seconds long.
Saving a Frame from a Movie as a Still Image
The desired frame of a recorded movie can be extracted and saved as a still image.
• Pause a movie and display the frame to be
• Use the multi selector JK to select the
H control and press the k button.
• Select Yes when a confirmation dialog is displayed, and press the k button to save the image.
• The image quality of the saved still image is normal (compression ratio of approximately
Copy this frame as a still image?
Yes
1:8). The image size is determined by the type
(image size) ( E54) of the original movie.
No
For example, a still image saved from a movie recorded with e 1080/30p (or S 1080/25p) is n (1920 × 1080 pixels).
B
Notes About Saving Still Images
Frames of movies recorded with Z 1080/60i or U 1080/50i, or g 480/30p or W 480/25p, and HS movies (
E54) cannot be saved as still images.
E 29
The Shooting Menu (for A (Auto) Mode)
Image Mode Settings (Image Size and Quality)
Enter shooting mode M d button M Image mode M k button
Select the combination of image size and compression ratio that is used when saving images.
The higher the image mode setting, the larger the size at which it can be printed, and the lower the compression ratio, the higher the quality of the images, but the number of images that can be saved is reduced.
Option* Compression ratio
Aspect ratio
(horizontal to vertical)
4:3 Q 4608×3456P
P 4608×3456
(default setting)
R 3264×2448 r 2272×1704 q 1600×1200
O 640×480 l 4608×2592 s 3456×3456
Approx. 1/4
Approx. 1/8
Approx. 1/8
Approx. 1/8
Approx. 1/8
Approx. 1/8
Approx. 1/8
Approx. 1/8
4:3
* The total number of pixels captured, and the number of pixels captured horizontally and vertically.
Example: P 4608×3456 = approx. 16 megapixels, 4608 × 3456 pixels
4:3
4:3
4:3
4:3
16:9
1:1
E 30
C
Notes About Image Mode
• The image mode setting can also be changed in shooting modes other than auto.
The changed setting is also applied to other shooting modes.
• The setting may not be changed when using certain settings of other functions.
C
Number of Images That Can Be Saved
• The approximate number of images that can be saved can be checked in the
• Note that due to JPEG compression, the number of images that can be saved may vary greatly depending on the image content, even when using memory cards with the same capacity and the same image mode setting. In addition, the number of images that can be saved may vary depending on the make of the memory card.
• If the number of exposures remaining is 10,000 or more, the number of exposures remaining display shows “9999”.
C
Printing Images at 1:1 Aspect Ratio
Change the printer setting to “Border” when printing images at a 1:1 aspect ratio.
Some printers may not be able to print images at a 1:1 aspect ratio.
E 31
White Balance (Adjusting Hue)
Select A (auto) mode M d button M A menu icon M White balance
M k button
Adjust white balance to suit the light source or weather conditions in order to make the colors in images match what you see with your eyes.
• Use Auto under most conditions. Change the setting when you want to adjust the hue of the image you are taking.
Option a Auto
(default setting) b Preset manual c Daylight d Incandescent e Fluorescent f Cloudy g Flash
Description
White balance is automatically adjusted to suit lighting conditions.
Use when the desired result is not achieved with Auto,
White balance adjusted for direct sunlight.
Use under incandescent lighting.
Use under fluorescent lighting.
Use when taking images under overcast skies.
Use with the flash.
B
Notes About White Balance
• Set the flash to W (off) when white balance is set to any setting other than Auto
• The setting may not be changed when using certain settings of other functions.
E 32
Using Preset Manual
Use the procedure below to measure the white balance value under the lighting used during shooting.
1
Place a white or gray reference object under the lighting that will be used during shooting.
2
Use the multi selector HI to select Preset manual in the
White balance menu, and press
the k button.
• The camera zooms in to the position for measuring white balance.
White balance
Preset manual
3
Select Measure.
• To apply the last measured value, select
Cancel and press the k button.
Preset manual
4
Frame the reference object in the measuring window.
Cancel
Measure
Preset manual
Cancel
Measure
Measuring window
5
Press the k button to measure the value.
• The shutter is released and measurement is complete. No image is saved.
B
Notes About Preset Manual
A value for flash lighting cannot be measured with Preset manual. When shooting using the flash, set White balance to Auto or Flash.
E 33
Continuous Shooting
Select A (auto) mode M d button M A menu icon M Continuous M k button
Option
U Single
(default setting) k Continuous H m Continuous L q Pre-shooting cache n Continuous H:
120 fps j Continuous H:
60 fps
Description
One image is taken each time the shutter-release button is pressed.
While the shutter-release button is held all the way down, images are captured continuously.
• The frame rate for continuous shooting is about 6.9 fps and the maximum number of continuous shots is about
5 (when image mode is set to P 4608×3456).
While the shutter-release button is held all the way down, images are captured continuously.
• The frame rate for continuous shooting is about 2.2 fps and the maximum number of continuous shots is about
33 (when image mode is set to P 4608×3456).
When the shutter-release button is pressed halfway, preshooting cache shooting begins. When the shutterrelease button is pressed the rest of the way down, the camera saves the current image as well as the images captured immediately before the button is pressed
(
E36). This function helps you to avoid missing the shot.
• The frame rate for continuous shooting is about 20 fps and the maximum number of continuous shots is 25, including a maximum of 5 frames captured in the preshooting cache.
• Image mode is fixed at M (image size: 1280 × 960 pixels).
Each time the shutter-release button is pressed all the way, images are captured at a high speed rate.
• The frame rate for continuous shooting is about 120 fps and the maximum number of continuous shots is 50.
• Image mode is fixed at O 640×480.
Each time the shutter-release button is pressed all the way, images are captured at a high speed rate.
• The frame rate for continuous shooting is about 60 fps and the maximum number of continuous shots is 25.
• Image mode is fixed at M (image size: 1280 × 960 pixels).
E 34
Option Description
D BSS
(Best Shot Selector)
While the shutter-release button is held all the way down, the camera captures a series of up to 10 images and automatically saves the sharpest image.
Use when shooting a stationary subject in a place where flash photography is prohibited and camera shake is likely to occur.
W Multi-shot 16
Each time the shutter-release button is pressed all the way down, the camera captures a series of 16 images and saves it as a single image.
• The frame rate for continuous shooting is about 30 fps.
• Image mode is fixed at L (image size: 2560 × 1920 pixels).
• Digital zoom cannot be used.
B
Notes About Continuous Shooting
• Focus, exposure, and white balance are fixed at the values determined with the first image in each series.
• It may take some time to save the images after shooting.
• When ISO sensitivity increases, noise may appear in captured images.
• The frame rate for continuous shooting may become slow depending upon the current image mode setting, the memory card used, or shooting condition.
• When using Pre-shooting cache, Continuous H: 120 fps, Continuous H: 60
fps, or Multi-shot 16, banding or variance in brightness or hue may occur in images that were captured under lighting that flickers at high speeds, such as fluorescent, mercury-vapor, or sodium-vapor lighting.
E 35
C
Pre-shooting Cache
When the shutter-release button is pressed halfway or all the way down, images are saved in the manner described below.
Press down halfway Press down all the way
Images saved by pressing halfway
Images saved by pressing all the way
• The pre-shooting cache icon (Q) in the monitor glows green while the shutterrelease button is pressed halfway.
E 36
ISO Sensitivity
Select A (auto) mode M d button M A menu icon M ISO sensitivity
M k button
Higher ISO sensitivity allows darker subjects to be captured. Additionally, even with subjects of similar brightness, images can be taken at faster shutter speeds, and blurring caused by camera shake and subject movement can be reduced.
• When higher ISO sensitivity is set, images may contain noise.
Option a Auto
(default setting)
I Fixed range auto
Description
Sensitivity is automatically selected from the range of ISO
125 to 1600.
Select the range in which the camera automatically adjusts ISO sensitivity, from ISO 125-400 or ISO 125-800.
125, 200, 400, 800,
1600, 3200, 6400
Sensitivity is locked at the specified value.
B
Notes About ISO Sensitivity
The setting may not be changed when using certain settings of other functions.
C
ISO Sensitivity Display on the Shooting Screen
• When Auto is selected, E is displayed if the ISO sensitivity automatically increases.
• When Fixed range auto is selected, the maximum value for ISO sensitivity is displayed.
E 37
AF Area Mode
Select A (auto) mode M d button M A menu icon M AF area mode
M k button
Use this option to determine how the camera selects the focus area for autofocus when shooting still images.
Option Description
When the camera detects a human face, it focuses on that
information.
40
30
20
10
0
-10
15m
1010hPa a Face priority
When framing a composition with no human subjects or detected faces, the camera automatically selects one or more of the 9 focus areas containing the subject closest to the camera when the shutter-release button is pressed halfway.
x Manual
Use the multi selector
HIJK to move the focus area to where you want to focus.
• To use the multi selector to configure the flash mode or other settings, press the k button. To return to moving the focus area, press the k button again.
Focus area
1/250 F2.8
Focus areas
Scope of movable focus area
Focus area
E 38
Option y Center
Description
The camera focuses on the subject in the center of the frame.
40
30
20
10
0
-10
15m
1010hPa s Subject tracking
M Target finding AF
(default setting)
Use this function to take images of moving subjects.
Register the subject on which the camera focuses. The focus area automatically moves to
more information.
When the camera detects the main subject, it focuses on that subject.
40
30
20
10
0
-10
15m
1010hPa
40
30
20
10
0
-10
15m
1010hPa
Focus area
Start
Focus areas
B
Notes About AF Area Mode
• When digital zoom is in effect, the camera focuses on the area in the center of the frame regardless of the AF area mode setting.
• The setting may not be changed when using certain settings of other functions.
C
AF Area Mode for Movie Recording
AF area mode for movie recording can set with AF area mode (
menu.
E 39
Using Subject Tracking
Select A (auto) mode M d button M A menu icon M AF area mode
M k button M s Subject tracking M k button M d button
1
Register a subject.
• Align the subject that you want to track with the border in the center of the monitor and press the k button.
• When the subject is registered, a yellow border (focus area) is displayed around that subject and the camera begins tracking
40
30
20
10
0
-10
15m
1010hPa that subject.
• If the subject cannot be registered, the border glows red. Change the composition
Start and try registering the subject again.
• To cancel subject registration, press the k button.
• If the camera can no longer track the registered subject, the focus area disappears. Register the subject again.
2
Press the shutter-release button fully to take the picture.
• If the shutter-release button is pressed while the focus area is not displayed, the camera focuses on the area in the center of the frame.
1/250 F2.8
B
Notes About Subject Tracking
• If you perform operations such as zooming while the camera is tracking the subject, the registration is canceled.
• Subject tracking may not be possible in certain shooting conditions.
E 40
Autofocus Mode
Select A (auto) mode M d button M A menu icon M Autofocus mode M k button
Select how the camera focuses when shooting still images.
Option Description
A Single AF
B Full-time AF a Pre-focus
(default setting)
The camera focuses only when the shutter-release button is pressed halfway.
The camera continues focusing even when the shutterrelease button is not pressed halfway. The sound of lens drive movement is heard while the camera focuses.
Even when the shutter-release button is not pressed halfway, the camera focuses automatically if the composition of the framed image is significantly changed.
C
Autofocus Mode for Movie Recording
Autofocus mode for movie recording can be set with Autofocus mode ( E59) in
the movie menu.
Quick Effects
Select A (auto) mode M d button M A menu icon M Quick effects
M k button p On
(default setting)
Off
Option Description
In A (auto) mode, press the k button immediately after releasing the shutter to display the effect selection screen and use the quick effects function (
Disables the quick effects function (during shooting).
B
Notes About Quick Effects
The setting may not be changed when using certain settings of other functions.
E 41
The Smart Portrait Menu
• See “Image Mode Settings (Image Size and Quality)” (E30) for information
about Image mode.
Skin Softening
Select smart portrait mode M d button M F menu icon M Skin softening M k button
Option
S High
R Normal
(default setting)
Q Low
Off
Description
When the shutter is released, the camera detects one or more human faces (up to 3), and processes the image to soften facial skin tones before saving the image. You can select the amount of effect that is applied.
Turns skin softening off.
The effects of skin softening are not visible when framing images for shooting.
Check the results in playback mode, after taking images.
E 42
Smile Timer
Select smart portrait mode M d button M F menu icon M Smile timer M k button
The camera detects human faces and then automatically releases the shutter whenever a smile is detected.
Option a On
(default setting)
Off
Description
Whenever a smile is detected, the camera automatically releases the shutter.
Turns the smile timer off.
B
Notes About Smile Timer
The setting may not be changed when using certain settings of other functions.
E 43
Blink Proof
Select smart portrait mode M d button M F menu icon M Blink proof
M k button
Option Description y On
Off (default setting)
The camera automatically releases the shutter twice with every shot and saves one image in which the subject's eyes are open.
• If the camera saved an image in which
A blink was detected in the picture just taken.
the subject’s eyes may have been closed, the dialog shown on the right is displayed for a few seconds.
Turns the blink proof off.
B
Notes About Blink Proof
The setting may not be changed when using certain settings of other functions.
E 44
The Playback Menu
• See “Editing Still Images” (E13) for information about image editing
functions.
• See “Favorite Pictures Mode” (E5) for information about Favorite
pictures and Remove from favorites.
Print Order (Creating a DPOF Print Order)
Press the c button (playback mode) M d button M Print order M k button
If you configure print order settings in advance, you can use them with the printing methods listed below.
• Taking the memory card to a digital photo lab that supports DPOF (Digital
Print Order Format) printing.
• Inserting the memory card into a DPOF-compatible printer’s card slot.
• Connecting the camera to a PictBridge-compatible printer (E22).
1
Use the multi selector HI to select Select images and press the k button.
• In favorite pictures, auto sort, or list by date mode, the screen shown on the right is not displayed. Proceed to step 2.
Print order
Select images
Delete print order
E 45
2
Select images (up to 99) and the number of copies (up to 9) of each.
Print selection
• Use the multi selector JK to select images, and use HI to specify the number of copies to be printed.
• Images selected for printing are indicated by
M and the numeral indicating the number
Back
1 1 of copies to be printed. If no copies have been specified for images, the selection is canceled.
• Move the zoom control toward g (i) to switch to full-frame playback or f (h) to switch to thumbnail playback.
• Press the k button when setting is complete.
3
3
Select whether or not to print shooting date and shooting information.
Print order
Done
• Select Date and press the k button to print the shooting date on all images.
• Select Info and press the k button to print the shutter speed and aperture value on all
Date
Info images.
• Lastly, select Done and press the k button to complete the print order.
B
Notes About Printing Shooting Date and Shooting Information
• Some printers may not be able to print the shooting date and shooting information.
• Shooting information is not printed when the camera is connected to a printer.
• The Date and Info settings are reset each time the Print order option is displayed.
• The date printed is that saved when the image was captured.
• For images taken with the Print date (E67)
option enabled, only the date imprinted at the time of shooting is printed, even if the Print
order date option is enabled for the images.
E 46
B
Notes About Print Order
When a print order is created in favorite pictures mode, auto sort mode, or list by date mode, the screen shown below is displayed if images other than those in the selected album, category, or shooting date have been marked for printing.
• Yes: Does not remove print markings from other images, and adds the current print order settings.
• No: Removes print markings from all other images, and uses only the current print order settings.
Save print marking for other images?
Yes
No
Save print marking for other dates?
Yes
No
Favorite pictures mode or auto sort mode
List by date mode
If the total number of the images in the print order exceeds 99 when the new settings are applied, the screen shown below is displayed.
• Yes: Removes print markings from all other images, and uses only the current print order settings.
• Cancel: Does not remove print markings from other images, and cancels the current print order settings.
Too many images selected.
Remove print marking from other images?
Yes
Cancel
Too many images selected.
Remove print marking for other dates?
Yes
Cancel
Favorite pictures mode or auto sort mode
List by date mode
C
Canceling Existing Print Order
Select Delete print order in step 1 of “Print Order (Creating a DPOF Print Order)”
C
More Information
See “Printing Images at 1:1 Aspect Ratio” ( E31) for more information.
E 47
Slide Show
Press the c button (playback mode) M d button M Slide show M k button
Play back images one by one in an automated “slide show.” When movie files are played back in the slide show, only the first frame of each movie is displayed.
1
Use the multi selector HI to select Start and press the k button.
Slide show
Start
Effects 1
• The slide show begins.
• Before selecting Start, select the following options and press the k button to change the setting.
- Effects: Select the effect for a slide show from Classic (default setting) or Zoom.
Background music
Frame intvl
Loop
Pause
- Background music: Select BGM from ON/OFF (default setting).
- Frame intvl: Select Manual advance only or display time of an image.
- Loop: To repeat the slide show automatically, press the k button to display
B.
• The maximum playback time is up to about 30 minutes even if Loop is enabled.
2
Select End or Restart.
• The screen shown on the right is displayed after the slide show ends or is paused. To exit the show, select G and then press the k button. To resume the slide show, select
F and then press the k button.
Operations During Playback
• Use JK to display the previous/next image. Press and hold to rewind/fast forward.
• When Background music is set, press the zoom control g or f to adjust the volume.
• Press the k button to pause or end the slide show.
E 48
Protect
Press the c button (playback mode) M d button M Protect M k button
The camera protects selected images from accidental deletion.
Select images to protect or cancel protection for previously protected images
from the image selection screen ( E49).
Note that formatting the camera’s internal memory or the memory card permanently deletes protected files (
The Image Selection Screen
When an image selection screen such as the one shown on the right is displayed while operating the camera, follow the procedures described below to select the images.
Protect
Back
1
Use the multi selector JK to select an image.
• Move the zoom control (A2) toward g (i)
to switch to full-frame playback or f (h) to switch to thumbnail playback.
• Only one image can be selected for Rotate
image, Choose key picture, and
Welcome screen. Proceed to step 3.
2
Use
HI to select or deselect (or to specify the number of copies).
• When an image is selected, an icon is displayed below the image. Repeat steps 1 and 2 to select additional images.
Protect
Back
Protect
Back
3
Press the k button to apply image selection.
• When Selected images is selected, a confirmation dialog is displayed.
Follow the instructions displayed in the monitor.
E 49
Rotate Image
Press the c button (playback mode) M d button M Rotate image M k button
Specify the orientation in which saved images are displayed during playback.
Still images can be rotated 90 degrees clockwise or 90 degrees counterclockwise.
Select an image from the image selection screen ( E49). When the Rotate
image screen is displayed, use the multi selector JK to rotate the image 90 degrees.
Rotate image Rotate image Rotate image
Back Rotate
Rotate 90 degrees counterclockwise
Back Rotate Back Rotate
Rotate 90 degrees clockwise
Press the k button to finalize display orientation, and save orientation information with the image.
E 50
Voice Memo
Press the c button (playback mode) M select an image M d button
M Voice memo M k button
Voice memos can be recorded and attached to images.
Recording Voice Memos
• Press and hold the k button to record (up to about 20 seconds).
• Do not touch the microphone.
• During recording, o and p flash in the monitor.
• The voice memo playback screen is displayed after recording ends. Press the k button to play back the voice memo.
• Delete the current voice memo before recording a new voice memo (
• p is displayed for images with a voice memo when in full-frame playback mode.
Playing Voice Memos
Select an image with p displayed before pressing the d button.
• Press the k button to play the voice memo.
Press the button again to stop playback.
• Move the zoom control during playback to adjust playback volume.
Back
Deleting Voice Memos
Press the l button while the screen described
in “Playing Voice Memos” ( E51) is displayed.
When the confirmation dialog is displayed, use the multi selector HI to select Yes and press the k button.
• To delete a voice memo for a protected image, the Protect setting must first be disabled.
File will be deleted. OK?
Yes
No
E 51
Copy (Copy Between Internal Memory and
Memory Card)
Press the c button (playback mode) M d button M Copy M k button
Copy images between the internal memory and a memory card.
1
Use the multi selector HI to select a destination option to which images are copied and press the k button.
Copy
Camera to card
Card to camera
2
Select a copy option and press the k button.
• If you choose the Selected images option, use the image selection screen to specify
• If you choose the Card to camera option, the
All images option is not available.
Camera to card
Selected images
All images
B
Notes About Copying Images
• Only files in formats that this camera can record can be copied.
• Operation is not guaranteed with images captured with another make of camera or that have been modified on a computer.
• The Print order (E45) settings configured for images are not copied.
• Copied images or movies cannot be displayed in auto sort mode (E9).
• If an image added to an album (E5) is copied, the copied image is not added to
the album.
E 52
C
Notes About Copying Images in a Sequence
• If you select a key picture of a sequence in Selected images, all images in the sequence are copied.
• If you press the d button while images in a sequence are displayed, only the
Card to camera copy option is available. All images in the sequence are copied if you select Current sequence.
C
Copying to a Memory Card That Contains No Images
When the camera is switched to playback mode, Memory contains no images. is displayed. Press the d button to select Copy.
Sequence Display Options
Press the c button (playback mode) M d button M Sequence display options M k button
Select the method used to display images in the sequence ( E11).
Option Description
Q Individual pictures
Displays each image in a sequence individually. F is displayed on the playback screen.
C Key picture only
(default setting)
Displays only the key picture for images in a sequence.
Settings are applied to all sequences, and the setting is saved in the camera’s memory even if the camera is turned off.
Choose Key Picture
Press the c button (playback mode) M display a sequence for which you want to change the key picture M d button M Choose key picture M k button
Specify a different image in the sequence as the key picture.
• When the key picture selection screen is displayed, select an image (E49).
E 53
The Movie Menu
Movie Options
Enter shooting mode M d button M D menu icon M Movie options
M k button
Select the desired movie option to record.
Select normal speed movie options to record at normal speed, or HS movie
options ( E55) to record in slow or fast motion.
• Memory cards (Class 6 or higher) are recommended for recording movies
(
Normal Speed Movie Options
Option
(Image size/Frame rate
1
,
File format) e 1080/30p
S 1080/25p
(default setting)
Z 1080/60i
U 1080/50i f 720/30p
V 720/25p p iFrame 720/30p 2 p iFrame 720/25p 2 g 480/30p
W 480/25p
Image size
1920 × 1080
1920 × 1080
1280 × 720
1280 × 720
640 × 480
Aspect ratio
(horizontal to vertical)
16:9
16:9
16:9
16:9
4:3
1
2
The items and frame rate that can be set vary depending on the Frame rate
setting in the movie menu ( E61).
iFrame is a format supported by Apple Inc. When recording movies to the internal memory, recording may stop before the maximum movie length is reached.
E 54
HS Movie Options
Recorded movies are played back in fast or slow motion.
See “Recording Movies in Slow Motion and Fast Motion (HS Movie)” ( E56).
Option
Image size
Aspect ratio
(horizontal to vertical)
Description k k
HS 240/8× h a
HS 480/4× i
X
HS 720/2× j
Y
HS 1080/0.5×
320 × 240
4:3
640 × 480
4:3
1280 × 720
16:9
1920 × 1080
16:9
1/8-speed slow motion movies
• Max. recording time*: 10 seconds
(playback time: 1 minute 20 seconds)
1/4-speed slow motion movies
• Max. recording time*: 15 seconds
(playback time: 1 minute)
1/2-speed slow motion movies
• Max. recording time*: 30 seconds
(playback time: 1 minute)
2× speed fast motion movies
• Max. recording time*: 2 minutes
(playback time: 1 minute)
* While recording movies, the camera can be switched between normal speed movie recording and slow motion or fast motion movie recording.
The maximum recording time shown here refers only to the portion of the movie that is recorded in slow motion or fast motion.
B
Notes About HS Movie
• Sound is not recorded.
• Zoom position, focus, exposure, and white balance are locked when movie recording starts.
E 55
Recording Movies in Slow Motion and Fast Motion
(HS Movie)
Enter shooting mode M d button M D menu icon M Movie options
M k button
Movies recorded using HS movie can be played back in slow motion at 1/8, 1/4 or 1/2 of the normal playback speed, or in fast motion at twice the normal playback speed.
1
Use the multi selector HI to
select an HS movie option ( E55)
and press the k button.
• After applying the option, press the d button to return to the shooting screen.
Movie options
HS 480/4×
HS 720/2×
HS 1080/0.5×
2
Press the b (e movie-record) button to start recording.
• Movie recording starts at high speed when the Open with HS footage option in the movie menu is set to On, or at normal speed when it is set to Off.
• The camera switches between normal speed movie recording and HS movie recording each time the k button is pressed.
• The movie options icon changes when switching between HS movie recording and normal speed movie recording.
• When the maximum recording time for HS movies (E55) is reached, the
camera automatically switches to normal speed movie recording.
3
Press the b (e movie-record) button to end recording.
E 56
C
Playing Back in Slow Motion and Fast Motion
When recording at normal speed:
Recording time 10 s
Playback time 10 s
When recording at h HS 480/4× (a HS 480/4×):
Movies are recorded at 4× normal speed.
They are played back in slow motion at 4× slower speed.
Recording time 10 s
Playback time 40 s
Slow motion playback
When recording at j HS 1080/0.5× (Y HS 1080/0.5×):
Movies are recorded at 1/2 normal speed.
They are played back in fast motion at 2× faster speed.
Recording time 10 s
Playback time 5 s
Fast motion playback
E 57
Open with HS Footage
Enter shooting mode M d button M D menu icon M Open with HS footage M k button
Set whether to start recording HS movies or at normal speed when recording movies.
Option
On (default setting)
Off
Description
Record HS movies when movie recording begins.
Record normal speed movies when movie recording begins.
AF Area Mode
Enter shooting mode M d button M D menu icon M AF area mode M k button
Use this option to determine how the camera selects the focus area for autofocus during movie recording.
Option a Face priority
(default setting) y Center
Description
When the camera detects a human face, it focuses on
that face. See “Using Face Detection” ( A62) for more
information.
The camera focuses on the subject in the center of the frame.
B
Notes About AF Area Mode for Movie Recording
AF area mode is set to focus on the center in the following situations even when
Face priority is selected.
• When Movie VR is set to On (hybrid) and Movie options is set to Z 1080/
60i or U 1080/50i.
• When Autofocus mode in the movie menu is set to Single AF and no faces are detected before pressing the b (e movie-record) button.
• When an HS movie option is selected in Movie options.
E 58
Autofocus Mode
Enter shooting mode M d button M D menu icon M Autofocus mode
M k button
Set how the camera focuses in movie mode.
Option
A Single AF
(default setting)
Description
Focus is locked when the b (e movie-record) button is pressed to start recording.
Select this option when the distance between the camera and the subject will remain fairly consistent.
B Full-time AF
Camera focuses continuously.
Select this option when the distance between the camera and subject will change significantly during recording. The sound of the camera focusing may be heard in the recorded movie. Use of Single AF is recommended to prevent the sound of the camera focusing from interfering with recording.
• When an HS movie option is selected in Movie options, the setting is fixed at Single AF.
E 59
Movie VR
Enter shooting mode M d button M D menu icon M Movie VR M k button
Set to reduce the effects of camera shake while recording movies.
Set this option to Off when using a tripod to stabilize the camera during recording.
V On (hybrid)
(default setting) g On
Off
Option Description
Performs optical compensation for camera shake using the lens shift method. Also performs electronic VR using image processing. The angle of view (i.e., the area visible in the frame) becomes narrower.
Compensates for camera shake using the lens shift method.
Compensation is not performed.
B
Notes About Movie VR
The effects of camera shake may not be completely eliminated in some situations.
Movie Light
Enter shooting mode M d button M e menu icon M Movie light M k button
Enable or disable the movie light that assists recording in dark places during movie recording.
Option
On
Description
The movie light is turned on for lighting when movies are recorded.
Off
(default setting)
The movie light is turned off.
E 60
Wind Noise Reduction
Enter shooting mode M d button M D menu icon M Wind noise reduction M k button
Set whether or not to reduce wind noise during movie recording.
Option Description
Y On
Reduces the sound produced when wind passes over the microphone. Other sounds may become difficult to hear during playback.
Off (default setting) Wind noise reduction is not enabled.
• When an HS movie option is selected in Movie options, the setting is fixed at Off.
Frame Rate
Enter shooting mode M d button M D menu icon M Frame rate M k button
Select the frame rate used when recording movies.
When the frame rate is switched, available frame rates in Movie options
(
• 30 fps (30p/60i) is suitable for a TV using the NTSC system to play back movies, and 25 fps (25p/50i) for a TV using the PAL system.
E 61
The Setup Menu
Welcome Screen
Press the d button M z menu icon M Welcome screen M k button
Configure the welcome screen that is displayed when you turn on the camera.
Option
None
(default setting)
COOLPIX
Description
Does not display the welcome screen.
Select an image
Displays a welcome screen with the COOLPIX logo.
Displays an image selected for the welcome screen.
• The image selection screen is displayed. Select an
image ( E49) and press the k button.
• Because a copy of the selected image is saved in the camera, it will be displayed when the camera is turned on, even if the original image is deleted.
• Images captured using easy panorama cannot be selected.
• An image cannot be selected if the image size is extremely small after the small picture or crop function is applied.
E 62
Time Zone and Date
Press the d button M z menu icon M Time zone and date M k button
Set the camera clock.
Option
Date and time
Date format
Time zone
Description
• Select an item: Press the multi selector JK (changes between D, M, Y, h, and m).
• Edit the date and time: Press
HI.
• Apply the setting: Select the
m setting and press the k button.
Date and time
D M Y
15 05 2014 h m
15 10
Edit
Select Year/Month/Day, Month/Day/Year, or Day/Month/
Year.
Set time zone and daylight saving time.
• When Travel destination (x) is set after having set the home time zone (w), the time difference between the travel destination and the home time zone is automatically calculated, and the date and time are saved for the selected region.
E 63
Setting the Time Zone
1
Use the multi selector HI to select Time zone and press the k button.
2
Select w Home time zone or x
Travel destination and press the
k button.
• The date and time displayed in the monitor changes depending on whether the home time zone or travel destination is selected.
3
Press K.
4
Use JK to select the time zone.
• Press H to enable daylight saving time function, and W is displayed. Press I to disable the daylight saving time function.
• Press the k button to apply the time zone.
• If the correct time is not displayed for the home or travel destination time zone setting, set the appropriate time in Date
and time.
Time zone and date
Date and time
Date format
Time zone
London, Casablanca
15/05/2014 15:30
Time zone
Home time zone
Travel destination
Tokyo, Seoul
15/05/2014 23:30
Time zone
Home time zone
Travel destination
Tokyo, Seoul
15/05/2014 23:30
New York, Toronto, Lima
10:30 –5:00
Back
Time zone
Home time zone
Travel destination
New York, Toronto, Lima
15/05/2014 10:30
E 64
Monitor Settings
Press the d button M z menu icon M Monitor settings M k button
Option Description
Photo info
Image review
Brightness
Set whether or not to display information in the monitor.
This setting determines whether or not the captured image is displayed immediately after shooting.
• Default setting: On
Select from 5 settings.
• Default setting: 3
B
Notes About Monitor Settings
When Quick effects ( E41) is set to On, the captured image is displayed after each
shot regardless of the Image review setting.
Photo Info
Shooting mode Playback mode
Show info
Auto info
(default setting)
Hide info
20
10
40
30
0
-10
15m
1010hPa
15m
1010hPa
0004. JPG
15/05/2014 15:30
Current settings and operation guide are displayed as in Show
info.
If no operations are performed for a few seconds, the information is hidden as in Hide info. Information is displayed again when the next operation is performed.
20
10
0
-10
40
30
E 65
E 66
Shooting mode
20
10
40
30
0
-10
15m
1010hPa
Framing grid+auto info In addition to information shown with Auto info, a framing grid is displayed to help frame images.
The framing grid is not displayed when recording movies.
15m
1010hPa
Playback mode
0004. JPG
15/05/2014 15:30
The current settings or operation guide is displayed as in Auto info.
Movie frame+auto info
40
30
20
10
0
-10
15m
1010hPa
In addition to information shown with Auto info, a frame is displayed before recording begins that represents the area that will be captured when recording movies.
The movie frame is not displayed when recording movies.
0004. JPG
15/05/2014 15:30
The current settings or operation guide is displayed as in Auto info.
Print Date (Imprinting Date and Time)
Press the d button M z menu icon M Print date M k button
The shooting date and time can be imprinted on the images when shooting, allowing the information to be printed even from printers that do not support date printing (
Option Description f Date Date is imprinted on images.
S Date and time Date and time are imprinted on images.
Off (default setting) Date and time are not imprinted on images.
B
Notes About Print Date
• Imprinted dates form a permanent part of image data and cannot be deleted. The date and time cannot be imprinted on images after they have been captured.
• The date and time cannot be imprinted in the following situations:
- When the scene mode is set to Sports, Night portrait (when set to Hand-
held), Night landscape (when set to Hand-held), Museum, Backlighting
(when HDR is o), Easy panorama, or Pet portrait (when set to Continuous)
- When Continuous H, Continuous L, Pre-shooting cache, Continuous H:
120 fps, Continuous H: 60 fps or BSS is selected for Continuous ( E34)
- When recording movies
- When saving still images during movie recording
• The imprinted date and time may be difficult to read when using a small image size.
E 67
Photo VR
Press the d button M z menu icon M Photo VR M k button
Set to reduce the effects of camera shake while shooting still images.
Set this option to Off when using a tripod to stabilize the camera during shooting.
Option Description
V On (hybrid) g On
(default setting)
Performs optical compensation for camera shake using the lens shift method. Under the following conditions, also performs electronic VR using image processing.
• Flash: Does not fire
• Shutter speed: Slower than 1/30 second at the maximum wide-angle position and 1/60 second at the maximum telephoto position
• Self-timer: k
• Continuous setting: Single
• ISO sensitivity: ISO 200 or lower
The image recording time may be longer than usual.
Compensates for camera shake using the lens shift method.
Off Compensation is not performed.
B
Notes About Photo VR
• After turning on the camera or after switching from playback mode to shooting mode, wait for the shooting screen to be displayed completely before taking images.
• Images displayed on the shooting screen immediately after shooting may be displayed blurry.
• The effects of camera shake may not be completely eliminated in some situations.
• When the shutter speed is extremely slow, images cannot be compensated using image processing even when On (hybrid) is set.
E 68
Motion Detection
Press the d button M z menu icon M Motion detection M k button
Enable motion detection to reduce the effects of subject movement and camera shake when shooting still images.
Option
U Auto
(default setting)
Off
Description
Motion detection is enabled with some shooting modes or settings, when r is displayed on the shooting screen.
When the camera detects subject movement or camera shake, r turns green, and the ISO sensitivity and shutter speed are automatically increased to reduce blurring.
• Set ISO sensitivity (E37) to Auto in A (auto)
mode.
Motion detection is disabled.
B
Notes About Motion Detection
• Motion detection may be unable to eliminate the effects of subject movement and camera shake in some situations.
• Motion detection may be disabled if the subject exhibits significant movement or is too dark.
• The images captured using motion detection may be somewhat “grainy” in appearance.
AF Assist
Press the d button M z menu icon M AF assist M k button
Enable or disable the AF-assist illuminator which assists autofocus operation.
a Auto
(default setting)
Off
Option Description
The AF-assist illuminator automatically lights up when the subject is dimly lit. The illuminator has a range of about
3.0 m (9 ft 10 in.) at the maximum wide-angle position and about 3.0 m (9 ft 10 in.) at the maximum telephoto position.
• Note that for some scene modes or focus areas, the AFassist illuminator may not light.
The AF-assist illuminator does not light.
E 69
Digital Zoom
Press the d button M z menu icon M Digital zoom M k button
Option Description
On (default setting) Digital zoom is enabled.
Off Digital zoom is disabled.
B
Notes About Digital Zoom
• Digital zoom cannot be used in the following situations.
- When the scene mode is Portrait, Night portrait, Night landscape,
Backlighting (when HDR is o), Easy panorama, Pet portrait, or
Underwater.
- When smart portrait mode is selected
- When Continuous ( E34) is set to Multi-shot 16 in A (auto) mode
- When AF area mode ( E38) is set to Subject tracking in A (auto) mode
Sound Settings
Press the d button M z menu icon M Sound settings M k button
Option
Button sound
Shutter sound
Description
When On (default setting) is selected, the camera produces one beep when operations are performed, two beeps when focus is acquired on the subject, and three beeps when an error occurs. The start-up sound is also produced.
• Sounds are disabled when using Pet portrait scene mode.
When On (default setting) is selected, the shutter sound is produced when the shutter is released.
• The shutter sound is not produced when using continuous shooting mode, when recording movies, or when using Pet portrait scene mode.
E 70
Action Control Response
Press the d button M z menu icon M Action control response M k button
Set the sensitivity of the operation performed when shaking the camera (action
control) ( A4). When this option is set to High, the operation is performed
even if the camera shake movement is small. When this option is set to Low, the operation is performed if the camera shake movement is large. The default setting is Medium.
B
Notes About Action Control Response
When viewing images with Quick playback of action control or in full-frame playback mode, operation response of selecting images is fixed.
Playback Action Control
Press the d button M z menu icon M Playback action control M k button
Off
Option
On (default setting)
Description
An image can be selected by shaking the camera in fullframe playback mode.
The image cannot be selected by shaking the camera.
B
Notes About Playback Action Control
When Playback action control is set to On, the displayed images are not rotated automatically even if the orientation of the camera is changed.
E 71
Map actions
Press the d button M z menu icon M Map actions M k button
Off
Option
On (default setting)
Description
You can zoom in and out of maps by shaking the camera
(
You cannot zoom in and out of maps by shaking the camera.
B
Notes About Map actions
If the V (action) button is pressed, you cannot zoom in and out of maps.
Auto Off
Press the d button M z menu icon M Auto off M k button
Set the amount of time that elapses before the camera enters standby mode
(
You can select 30 s, 1 min (default setting), 5 min, or 30 min.
C
Notes About Auto Off
The time that passes before the camera enters standby mode is fixed in the following situations:
• When shooting with Pet portrait auto release: 5 minutes (if Auto off is set to 30
s or 1 min)
• When shooting with Smile timer: 5 minutes (if Auto off is set to 30 s or 1 min)
• When a menu is displayed: 3 minutes (if Auto off is set to 30 s or 1 min)
• When the AC adapter is connected: 30 minutes
E 72
Format Memory/Format Card
Press the d button M z menu icon M Format memory/Format card M k button
Use this option to format the internal memory or a memory card.
Formatting the internal memory or memory cards permanently deletes
all data. Data that has been deleted cannot be recovered. Make sure to transfer important images to a computer before formatting.
• Do not turn the camera off or open the battery-chamber/memory card slot cover during formatting.
Formatting the Internal Memory
Remove the memory card from the camera. The
Format memory option is displayed in the setup menu.
All images will be deleted! OK?
Format
No
Formatting Memory Cards
Insert a memory card in the camera. The
Format card option is displayed in the setup menu.
All images will be deleted! OK?
Format
No
E 73
Language
Press the d button M z menu icon M Language M k button
Select a language for display of camera menus and messages.
TV Settings
Press the d button M z menu icon M TV settings M k button
Adjust settings for connection to a TV.
Option Description
HDMI
HDMI device control
Select a resolution for HDMI output. When Auto (default setting) is selected, the option best suited to the TV to which the camera is connected is automatically selected from 480p, 720p, or 1080i.
When On (default setting) is selected, the HDMI-CECcompatible TV’s remote control can be used to control the camera during playback (
C
HDMI and HDMI-CEC
HDMI (High-Definition Multimedia Interface) is a multimedia interface. HDMI-CEC
(HDMI-Consumer Electronics Control) allows compatible devices to inter-operate.
E 74
Charge by Computer
Press the d button M z menu icon M Charge by computer M k button a Auto
(default setting)
Off
Option Description
When the camera is connected to a computer that is running (
A92), the battery inserted into the camera is
automatically charged using power supplied by the computer.
The battery inserted into the camera is not charged when the camera is connected to a computer.
B
Notes About Charging with a Computer
• When connected to a computer, the camera automatically turns on and starts charging. If the camera is turned off, charging stops.
• About 4 hours and 10 minutes are required to charge a fully exhausted battery.
Charging time increases when images are transferred while the battery is charging.
• The camera turns off automatically if there is no communication with the computer for 30 minutes after the battery has finished charging.
B
When the Charge Lamp Quickly Flashes Green
Charging cannot be performed, possibly due to one of the reasons described below.
• The ambient temperature is not suited to charging. Charge the battery indoors with an ambient temperature of 5°C to 35°C (41°F to 95°F).
• The USB cable is not connected correctly, or the battery is faulty. Make sure the USB cable is connected correctly and replace the battery if necessary.
• The computer is in sleep mode and is not supplying power. Wake up the computer.
• The battery cannot be charged because the computer cannot supply power to the camera due to the computer’s settings or its specifications.
E 75
Blink Warning
Press the d button M z menu icon M Blink warning M k button
Select whether or not the camera detects human subjects that have blinked using face detection (
A62) when shooting in the following modes:
• G (easy auto) mode
• In the following scene modes: Portrait or Night portrait (when Tripod is
• A (auto) mode (when Face priority (E38) is selected for AF area mode
option)
Option Description
On
When one or more human subjects may have blinked in an image captured using face detection, the Did
someone blink? screen is displayed in the monitor.
Check the image and determine whether or not another image should be captured.
Off (default setting) Blink warning is disabled.
The Blink Warning Screen
Faces detected by the blink warning are displayed inside a border.
Did someone blink?
The operations described below are available.
• To enlarge the face: Move the zoom control toward g (i). If more than one face is detected, use the multi selector JK to select the desired face.
• To switch to full-frame playback: Move the zoom control toward f (h).
Zoom in Exit
If you press the k button, or if no operations are performed for a few seconds, the camera returns to shooting mode.
B
Notes About Blink Warning
• The blink warning is disabled at continuous settings other than Single (E34).
• The blink warning may not function properly in some shooting conditions.
E 76
Eye-Fi Upload
Press the d button M z menu icon M Eye-Fi upload M k button
Option b Enable
(default setting) c Disable
Description
Upload images created by the camera to a preselected destination.
Images are not uploaded.
B
Notes About Eye-Fi Cards
• Note that images will not be uploaded if signal strength is insufficient even if
Enable is selected.
• Remove your Eye-Fi card from the camera where wireless devices are prohibited.
Signals may be transmitted even if Disable is selected.
• Refer to the instruction manual of your Eye-Fi card for more information. In the event of malfunction, contact the card manufacturer.
• The camera can be used to turn Eye-Fi cards on and off, but may not support other
Eye-Fi functions.
• The camera is not compatible with the Endless Memory function. When it is set on a computer, disable the function. If the Endless Memory function is enabled, the number of images taken may not be displayed correctly.
• Eye-Fi cards are for use only in the country of purchase. Observe all local laws concerning wireless devices.
• Leaving the setting as Enable will result in the battery being depleted in a shorter period of time.
C
Eye-Fi Communication Indicator
The communication status of the Eye-Fi card in the camera can be confirmed in the monitor (
• w: Eye-Fi upload is set to Disable.
• x (lights): Eye-Fi upload enabled; waiting to begin upload.
• x (flashes): Eye-Fi upload enabled; uploading data.
• y: Eye-Fi upload enabled but no images available for upload.
• z: An error occurred. The camera cannot control the Eye-Fi card.
E 77
Reset All
Press the d button M z menu icon M Reset all M k button
When Reset is selected, the camera’s settings are restored to their default values.
• Some settings, such as Time zone and date or Language, are not reset.
C
Resetting File Numbering
To reset file numbering to “0001”, delete all images saved in the internal memory or on the memory card (
A31) before selecting Reset all.
Firmware Version
Press the d button M z menu icon M Firmware version M k button
View the current camera firmware version.
E 78
The Location Data Options Menu
Location data Options
Press the d button M z (location data options) menu icon M Location data options M k button
Option
Record location data
Update A-GPS file
Erase location data
Description
When set to On, signals are received from the positioning satellites, and positioning starts (
• Default setting: Off
A memory card is used to update the A-GPS (assist GPS) file. Using the latest A-GPS file can shorten the time needed for obtaining the location data.
See “Updating the A-GPS File” ( E79) for more
information.
The location data and POI information recorded on images are erased.
• The deleted location data or POI information cannot be recovered.
• The location data of images captured with cameras other than this camera cannot be erased.
Updating the A-GPS File
Download the latest A-GPS file from the website below, and use it to update the file.
http://nikonimglib.com/agps3/
• The A-GPS file for the COOLPIX AW120 is only available from the website above.
• To update the A-GPS file, set Record location data to Off. When On is selected, the A-GPS file cannot be updated.
1
Download the latest A-GPS file to the computer from the website.
2
Use a card reader or other device to copy the downloaded file to the “NCFL” folder of the memory card.
• The “NCFL” folder is located directly under the memory card root directory. If the memory card does not have “NCFL” folder, create a new folder.
E 79
3
Insert the memory card containing the copied file into the camera.
4
Turn on the camera.
5
Press the d button to display the Location data options menu, and use the multi selector to select Location data
options.
6
Select Update A-GPS file, and update the file.
• About 2 minutes are needed to update the A-GPS file.
B
Notes About Updating A-GPS File
• The A-GPS file is disabled when a position is determined for the first time after the camera is purchased. The A-GPS file becomes active from the second operation for determining a location.
• The validity period of the A-GPS file can be checked on the update screen. If the validity period has expired, it is displayed in gray.
• Once the validity period of the A-GPS file has expired, obtaining the location data will not become faster. Updating of the A-GPS file before using the location data functions is recommended.
Distance Units
Press the d button M z (location data options) menu icon M Distance units M k button
The distance units of the map display can be selected from km (m) (kilometers, meters) (default setting) or mi (yd) (miles, yards).
E 80
Calculate Distance
Press the
c button (playback mode) M Display a map (A82) M d
button M z (location data options) menu icon M Calculate distance M k button
Calculate the linear distance from the current position to the shooting location of the image or between the shooting locations of two images.
1
Use the multi selector HI to select the desired option for
Calculate distance calculating the distance, and press the k button.
• Position now ⇔ image: Calculates the distance from the current position to the image shooting location. Confirmation of the current position starts. Proceed to step
Position now ⇔image
Image ⇔image
3.
• Image ⇔ image: Calculates the distance between the shooting locations of two images.
2
Use JK to select the image that is the start point, and press the k button.
• To adjust the scale of the map, use the zoom control ( f (h)/g (i)).
500m
Choose start point
Back Select image
3
Press JK to select the image that is the end point.
• Each time an image is selected, the distance is displayed on the screen.
• To end distance calculation, press the k button.
500m
Choose end point
100m
Back Select image
Distance
B
Notes About Distance Calculation
• If the location data is not recorded on the image, the distance cannot be calculated.
• In order to calculate the distance using Position now ⇔ image, the current position must have been obtained (
E 81
Points of Interest (POI) (Recording and Displaying
Location Name Information)
Press the d button M z (location data options) menu icon M Points of interest (POI) M k button
Configure the POI (Points of Interest, location name information) settings.
Option Description
Embed POI
Display POI
Level of detail
Edit POI
Set whether or not to record the location name information on the images to be shot.
• Default setting: Off
• The location name information can be recorded on both still images and movies.
Set whether or not to display the location name information on the shooting screen or playback screen
(
If Embed POI was set to On when an image was taken, the location name information for the image is displayed on the playback screen.
• Default setting: Off
Set the display level of the location name information. A higher display level shows more detailed regional information.
• When set to level 1: country names are displayed.
• When set to levels 2 to 5: the information displayed varies depending on the country.
• When set to level 6: landmark names (facilities) are displayed.
If Update POI is selected during playback mode, the location name information recorded on the image can be changed. Before pressing the d button, select the image to change the location name information.
• When level 6 is selected, press the multi selector JK to change the landmark name.
• To change the POI information level, press the multi selector HI.
If Remove POI is selected, the location name information recorded on the image is deleted.
C
POI Display
If there is no location name information at the set display level, the location name information may not be displayed or “---” may be displayed.
E 82
Create Log (Record the Log of Movement
Information)
Press the d button M z (location data options) menu icon M Create log M k button
When log recording starts, the measured movement information is recorded until a preset time has elapsed at the interval set for Log interval.
• The recorded log data cannot be used by itself. To use the data, end log recording and save it to a memory card.
1
Use the multi selector HI to select a log to be recorded, and press the k button.
• Select a log to be recorded from the following logs.
Create log
Start all logs
End all logs
Start location log
End location log
Start depth log
- Start all logs: The location data, altitude and water depth information log data is recorded.
End depth log
- Start location log: The location data log data is recorded.
- Start depth log: The water depth information log data is recorded.
2
Select the log interval that will be used for recording a log, and press the k button.
• The intervals that can be set for recording a log vary depending on the log to be recorded.
Log interval
15 s
30 s
1 min
3 min
5 min
10 min
E 83
3
Select the duration that the log will be recorded, and press the k button.
• Log recording starts.
• The log data is recorded at the interval set for the Log interval until the preset time is reached.
• When Start depth log is selected, the duration for recording the log cannot be selected. The duration for recording the log is fixed at 1 hour.
• D is displayed on the screen during log recording (
4
When log recording is completed, end the log that was selected in step 1 using Create log of the
Location data options menu, and press the k button.
5
Select Save logs, and press the k button.
• The log data is saved to a memory card.
Start log
Log data for next 6 hrs
Log data for next 12 hrs
Log data for next 24 hrs
Log data for next 72 hrs
Create log
Start all logs
End all logs
Start location log
End location log
Start depth log
End depth log
End all logs
Save logs
Erase logs
E 84
B
Notes About Log Recording
• If the date and time are not set, the log cannot be recorded.
• Use a fully charged battery to prevent the camera from turning off during log recording. When the battery power becomes exhausted, log recording ends.
While the altitude log or water depth log is recorded, the battery is exhausted much faster. Exercise caution regarding the remaining battery level.
• Even when the camera is turned off, log recording is continuously performed until the preset time has elapsed if there is still time remaining for log recording.
• Log recording ends due to the operations below even when there is time remaining for log recording.
- The battery is removed
- Record location data in Location data options is set to Off when the location log is recorded
- Reset all in the setup menu is performed
- The setting of the internal clock (time zone or date and time) is changed
- An option to end log recording is selected in Create log on the Location data
• Log recording is paused during the operations below.
- During continuous shooting
- During movie recording
- When connected with a USB cable or HDMI cable
Log recording is resumed when the above operations are finished. However, to resume log recording after using the charging AC adapter, you must turn on the camera after disconnecting the USB cable from it.
• The log data is temporarily stored in the camera. New logs cannot be recorded if the log data remains in the camera. After recording log data, save it to a memory card.
• See “Log Data Saved on Memory Cards” (E100) for more information.
C
To Erase Log Data
• To erase the log data that is temporarily stored in the camera, select Erase logs in step 5.
• To erase the log data that is stored on the memory card, press the l button in
View log (
E 85
View Log
Press the d button M z (location data options) menu icon M View log
M k button
Check or erase the log data stored on the memory card using Create log
(
1
Use the multi selector HI to select a log to be displayed, and press the k button.
• Location logs: Display the recorded log data of location data.
• Altitude/depth logs: Display the recorded log data of altitude information or water depth information.
View log
Location logs
Altitude/depth logs
2
Select the log data to be displayed, and press the k button.
• B is displayed for the altitude log data and
C is displayed for the water depth log data.
• See “Log Data Saved on Memory Cards”
(
• See “To Erase Log Data” (E87) for more
information.
Location logs
2014/05/26 [2]
2014/05/26 [1]
2014/05/20
2014/05/18
2014/05/15
3
Check the movement route.
500m
When Location logs is selected
• Your movement route is displayed on the map.
• To adjust the scale of the map, use the zoom control ( f (h)/g (i)).
• To move the map display, use the multi selector.
• To erase the displayed log data, press the l button.
• The following operations can be performed when you press the k button.
- Location logs: The monitor display returns to that shown in step 2.
- Save location: You can save the location by selecting the location on a map and pressing the k button.
- Center on saved location: You can display the saved location in the center of the map by selecting it (
E 86
When Altitude/depth logs is selected
0 10 20 30 40 50 60 m / time
100
• The altitude information or water depth information is displayed on the graph.
• When the zoom control is moved toward g (i), a graph is enlarged. When the zoom control is moved toward f (h), the entire
80
60
40
20
0
26/05/2014 [2] 15:30 graph is displayed.
• To move the graph display, press the multi selector JK.
• When the k button is pressed, another image can be selected.
- Press the multi selector JK to select the image.
- To enlarge the image, move the zoom control toward g (i). To return to the graph display, move the zoom control toward f (h).
• To erase the displayed log data, press the l button.
• The monitor display returns to that shown in step 2 when the d button is pressed.
To Erase Log Data
Press the l button in step 2 to select either function.
• Selected log: The selected log data is erased.
• All logs: All log data stored on the memory card is erased.
C
Location Information Log Data
Log data is NMEA format-compliant.
However, display in all NMEA format-compliant software or on all NMEA formatcompliant cameras is not guaranteed.
E 87
Set Clock from Satellite
Press the d button M z (location data options) menu icon M Set clock from satellite M k button
Signals from the positioning satellites are used to set the date and time of the camera’s internal clock. Check the positioning status before setting the clock using this option.
B
Notes About Set Clock from Satellite
• To set the camera's internal clock, positioning must have been done successfully
• Date/time adjustment by Set clock from satellite is set according to the time zone set in Time zone and date (
A76, E63) of the setup menu. Check the
time zone before setting Set clock from satellite.
• The date/time set using Set clock from satellite is not as accurate as radio clocks.
Use Time zone and date in the setup menu to set the time if it is not accurate in
Set clock from satellite.
E 88
Electronic Compass
Press the d button M z (location data options) menu icon M
Electronic compass M k button
Option
Compass display
Description
Set whether or not to display a compass on the shooting screen.
• Default setting: Off
• The direction the camera is pointing is displayed based on measured direction information.
• When the camera lens faces downward, the compass display switches to a circle compass with a red arrow that points north.
- Display style: north, east, south and west
- Display range: 16 cardinal points
• The direction measured by the electronic compass can be imprinted on images using Data imprint in the playback menu (
Correct the compass when the compass direction is not displayed correctly.
When the screen shown on the right is displayed,
Compass correction swing the camera to draw a figure eight in the air while turning your wrist to face the camera
Move camera in a figure eight.
forward and backward, side to side, or up and down.
Compass correction
E 89
B
Notes About Using the Electronic Compass
• The electronic compass is not displayed when the camera lens is facing upwards.
• Do not use the electronic compass in this camera for mountain climbing and other specialized applications. The displayed information is intended as a general guide only.
• Direction may not be measured correctly near the following objects: magnets, metals, electrical motors, electrical home appliances or electrical power cables.
• Direction may not be measured correctly in the following places: in automobiles, trains, ships, airplanes, inside buildings or in underground malls
• Direction may not be measured correctly if the location data is not obtained.
E 90
Altitude/Depth Options
Press the d button M z (location data options) menu icon M
Altitude/depth options M k button
Option Description
Altimeter/depth gauge
Alt./depth correction
Altitude/depth units
Set whether or not to display the altimeter or depth gauge on the shooting screen.
• Default setting: On
The altitude or water depth value is compensated.
Use location data: The altitude is compensated using
Record location data function.
• When the confirmation dialog is displayed, choose
Yes and press the k button. The altitude is compensated using the displayed value.
• The data is not compensated underwater.
Correct manually: Enter the altitude or water depth to compensate the data.
• Use the multi selector HI to change the value and use the multi selector JK to change the input position of the digits.
• When the cursor is positioned on the rightmost digit, press the k button to set this value.
Reset: The compensation set using Use location data or
Correct manually is canceled.
• When the compensation cancellation dialog is displayed, choose Yes and press the k button. The compensated value is cancelled.
Set the unit of distance for displaying altitude or water depth to “m (meters)” (default setting) or “ft (feet).”
B
Notes About Altitude/Depth Options
To correct the altitude or water depth using Use location data of Alt./depth
correction, Record location data in Location data options of the Location data options menu must be set to On and also, positioning must have been performed based on signals received from four or more satellites (
E 91
The Wi-Fi Options Menu
Press the d button M q menu icon M k button
Configure the Wi-Fi (wireless LAN) settings to connect the camera and a smart device.
Option
Connect to smart device
Disable Wi-Fi
Options
Description
Select when wirelessly connecting the camera and a smart
device. See “Using the Wi-Fi (Wireless LAN) Function”
Select to terminate the wireless connection between the
camera and a smart device. See “Using the Wi-Fi (Wireless
LAN) Function” ( A89) for more information.
SSID:
Change the SSID. The SSID configured here is displayed on the smart device. Set a 1- to 24-character alphanumeric
SSID.
Auth./encryp.:
Select whether or not to encrypt the communications between the camera and the connected smart device.
Communications are not encrypted when Open (default setting) is selected.
Password:
Set the password. Set an 8- to 16-character alphanumeric password.
Channel:
Select the channel used for wireless connections.
Subnet mask:
Use the default setting (255.255.255.0) under normal conditions.
DHCP server IP address:
Use the default setting (192.168.0.10) under normal conditions.
Display the current settings.
Current settings
Restore default settings
Restore the Wi-Fi settings to their default values.
E 92
Operating the Text Input Keyboard
Character Input for SSID and Password
• Use the multi selector HIJK to select alphanumeric characters. Press the k button to enter the selected character in the text field and move the cursor to the next space.
• To move the cursor in the text filed, select N or O on the keyboard, and press the k button.
• To delete one character, press the l button.
• To apply the setting, select P on the keyboard and press the k button.
Text field
SSID
N i x x k o n AW1 2 0 x x x x x x
0 1 2 3 4 5 6 7 8 9
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z @
Back Delete
Keyboard
Character Input for Channel, Subnet mask and DHCP server IP address
• Use the multi selector HI to set the
DHCP server IP address numbers. To move to the next digit, press K or the k button. To return to the previous digit, press J.
• To apply the setting, select the last digit and press the k button.
1 9 2 . 1 6 8 .
0 .
1 0
Edit
E 93
Error Messages
Refer to the table below if an error message is displayed.
Display
Battery temperature is elevated. The camera will turn off.
The camera will turn off to prevent overheating.
Cause/Solution
The camera turns off automatically. Wait until the camera or battery temperature has cooled before resuming use.
Memory card is write protected.
This card cannot be used.
This card cannot be read.
Card is not formatted. Format card?
Not available if Eye-Fi card is locked.
Out of memory.
A
–
The write-protect switch is in the “lock” position.
Slide the write-protect switch to the “write” position.
An error occurred while accessing the memory card.
• Use an approved card.
• Check that the terminals are clean.
• Confirm that the memory card is correctly inserted.
The memory card has not been formatted for use in the camera.
Formatting deletes all data saved on the memory card. If you need to keep copies of any images, make sure to select No and save the copies to a computer or other medium before formatting the memory card. Select Yes and press the k button to format the memory card.
The write-protect switch of the Eye-Fi card is in the “lock” position.
An error occurred while accessing the Eye-Fi card.
• Check that the terminals are clean.
• Confirm that the Eye-Fi card is correctly inserted.
–
–
Delete images or insert a new memory card.
E 94
Display
Image cannot be saved.
Album is full. No further pictures can be added.
Sound file cannot be saved.
Image cannot be modified.
Cannot record movie.
Memory contains no images.
File contains no image data.
This file cannot be played back.
Cause/Solution
An error occurred while saving the image.
Insert a new memory card or format the internal memory or memory card.
The camera has run out of file numbers.
Insert a new memory card or format the internal memory or memory card.
A
The image cannot be used for the welcome screen.
There is insufficient space to save the copy.
Delete images from the destination.
200 images have already been added to the album.
• Remove some images from the album.
• Add to other albums.
A voice memo cannot be attached to this image.
• Voice memos cannot be attached to movies.
• Select an image captured with this camera.
–
Select images that support the editing function.
A time-out error occurred while saving the movie on the memory card.
Select a memory card with a faster write speed.
There are no images in the internal memory or on the memory card.
• Remove the memory card from the camera to play back images in the camera’s internal memory.
• To copy the images saved in the camera’s internal memory to the memory card, press the d button to select Copy in the playback menu.
No images have been added to the selected album.
No images are contained in the category selected in auto sort mode.
The file was not created or edited with this camera.
The file cannot be viewed on this camera.
View the file using a computer or the device used to create or edit this file.
–
E 95
E 96
Display
All images are hidden.
This image cannot be deleted.
Failed to set clock from satellite.
No A-GPS file found on card.
Update failed.
Unable to determine current position.
Cannot save to card.
Cause/Solution
There are no images available for a slide show, etc.
The image is protected.
Disable protection.
The camera clock was not set correctly.
Change the location or time and determine the location again.
An A-GPS file that can be updated is not found on the memory card.
Check the following items.
• Whether the memory card is inserted
• Whether the A-GPS file is stored on the memory card
• Whether the A-GPS file saved on the memory card is more recent than the A-GPS file saved in the camera
• Whether the A-GPS file is still valid
Unable to update A-GPS file.
The A-GPS file may be corrupted. Download the file from the website once more.
Unable to determine the current position when distance is calculated.
Change the location or time and determine the location again.
A memory card is not inserted.
Insert a memory card.
The maximum number of log data events that can be saved per day has been exceeded.
• Location logs: Up to 36 log data events per day
• Altitude and water depth logs: Up to 34 log data events each per day
The maximum number of log data events that can be saved in one memory card has been exceeded.
• Location logs: Up to 100 log data events
• Altitude log and water depth log: Combined total of up to 100 log data events
Replace the memory card with a new one or delete log data that is no longer required from a memory card.
A
–
–
–
–
Communications error
Display
Unable to correct compass.
No access.
Could not connect.
Wi-Fi connection terminated.
Lens error
System error
Cause/Solution
Unable to calibrate the electronic compass.
Swing the camera to draw a figure eight in the air outdoors while turning your wrist to face the camera forward and backward, side to side, or up and down.
The camera could not receive the communication signal from the smart device.
Select Connect to smart device in the Wi-Fi options menu, and wirelessly connect the camera and smart device again.
The camera failed to establish the connection while receiving the communication signals from the smart device. Select a different channel in Channel in Options in the Wi-Fi options menu and establish the wireless connection again.
A cable was connected to the camera while the camera and smart device were wirelessly connected, the battery level became low, or the connection was aborted due to poor connectivity. Check the status of the camera and establish the wireless connection again.
A lens error occurred.
Turn the camera off and then on again. If the error persists, contact your retailer or Nikonauthorized service representative.
An error occurred while communicating with the printer.
Turn the camera off and reconnect the USB cable.
An error occurred in the camera’s internal circuitry.
Turn the camera off, remove and reinsert the battery, and turn the camera on. If the error persists, contact your retailer or Nikonauthorized service representative.
A
E 97
Printer error: check printer status.
Printer error: check paper.
Printer error: paper jam.
Printer error: out of paper.
Display
Printer error: check ink.
Printer error: out of ink.
Printer error: file corrupt.
Cause/Solution
After solving the problem, select Resume and press the k button to resume printing.*
Load the specified size of paper, select Resume, and press the k button to resume printing.*
Remove the jammed paper, select Resume, and press the k button to resume printing.*
Load the specified size of paper, select Resume, and press the k button to resume printing.*
There is a problem with the printer’s ink.
Check the ink, select Resume, and press the k button to resume printing.*
Replace the ink cartridge, select Resume, and press the k button to resume printing.*
There is a problem with the image file to be printed.
Select Cancel and press the k button to cancel printing.
A
* See the documentation provided with your printer for further guidance and information.
–
–
–
–
–
–
–
E 98
File Names
Images, movies, or voice memos are assigned file names as follows.
D S C N 0 0 0 1 . J P G
Identifier (not shown on camera monitor) Extension (indicates file format)
Original still images (voice memo attachment included) and movies
Small copies (voice memo attachment included)
Cropped copies (voice memo attachment included)
Images created by an image editing function other than small picture or crop* (voice memo attachment included), and movies created by the movie editing function
DSCN
SSCN
RSCN
FSCN
Still images
Movies
Voice memos
.JPG
.MOV
.WAV
File number (assigned automatically in ascending order, starting with
“0001”)
* Including images edited using the quick effects function (
mode
• Voice memo file names have the same identifier and file number as the image to which the voice memo is attached.
E 99
C
Log Data Saved on Memory Cards
The log data is saved in the “NCFL“ folder.
File name : N140515 0 .log
(1) (2) (3)
(1) Date
(2) Identification number
(3) Extension
Date (last two digits of the year, and the month and day in
YYMMDD format) on which the log recording was started is assigned automatically.
To manage log data events that are recorded on the same date, ID numbers are assigned automatically in an ascending order, starting from “0,” in the order in which they are recorded.
• Location data logs: A total of 36 alphanumeric characters consisting of the numbers 0 to 9 or the letters A to Z.
• Altitude/water depth logs: A total of 34 alphanumeric characters consisting of the numbers 0 to 9 or the letters A to Z except I and O.
Signifies the file type
.log
Location data logs
.lga
Altitude logs
.lgb
Water depth logs
• Location data logs: Up to 36 files can be recorded a day and up to 100 files can be recorded on a memory card.
• Altitude/water depth logs: Up to 34 files can be recorded each per day and a combined total of 100 files can be recorded on a memory card.
E 100
Optional Accessories
Battery charger
Battery Charger MH-65
(Charging time when no charge remains: approx. 2 h 30 min)
AC Adapter EH-62F (connect as shown)
AC adapter
Make sure that the power connector cord has been properly aligned in power connector.
• While using the AC adapter, the battery-chamber/ memory card slot cover cannot be closed. Do not pull the cord of the AC adapter.
If the cord is pulled, the connection between the camera and power source is interrupted, and the camera turns off.
Availability may vary with country or region.
See our website or brochures for the latest information.
E 101
E 102
Technical Notes and Index
Caring for the Product.....................................
Charging AC Adapter ..........................................................................
Memory Cards........................................................................................
Cleaning and Storage......................................
Troubleshooting..............................................
USER LICENSE AGREEMENT FOR MAP DATA
AND LOCATION NAME DATA ........................
Specifications.................................................
Approved Memory Cards ...............................................................
Index ...............................................................
F 1
F 2
Caring for the Product
The Camera
To ensure continued enjoyment of this Nikon product, observe the precautions
described below in addition to the warnings in “For Your Safety” ( Avii-ix) and
“<Important> Shockproof, Waterproof, Dustproof, Condensation“ (
when using or storing the device.
B
Do Not Drop
The product may malfunction if subjected to strong shock or vibration.
B
Do Not Allow Damp to Enter Inside the Camera
This camera is provided with JIS/IEC protection class 8 (IPX8) equivalent waterproofing. If water seeps inside the camera, however, this could cause the components to rust and result in a high repair charge or the camera may not be repairable. After using the camera at the beach or underwater, make sure that the battery-chamber/memory card slot cover is firmly closed, and then immerse the camera in a shallow container filled with fresh water for ten minutes. After using the camera underwater, do not leave the camera wet for 60 minutes or more. This could cause deterioration of the waterproofing performance.
B
Prevent Water from Seeping Inside the Camera
If the inside of the camera becomes wet, this could result in camera malfunction and the camera may not be repairable. To prevent water seeping (water submersion) accidents, make sure to observe the following cautions when using the camera.
• When the battery-chamber/memory card slot cover is closed, make sure that the camera strap, hair, lint, dust, sand grains, other foreign substances, or dirt are not attached on the waterproofing packing and portions that make a contact with the waterproofing packing.
• Do not open and close the battery-chamber/memory card slot cover in areas exposed to water spray, high winds, dust or sand.
• When an external force is applied on the camera, it could become deformed or the airtight seals may become damaged and cause water to seep inside the camera.
Do not place a heavy object on the camera, drop the camera, or apply excessive force on the camera.
• If water seeps inside the camera, immediately stop using the camera. Wipe off moisture from the camera, and at once take the camera to your Nikon-authorized service representative.
B
Shock and Vibration
Do not drop the camera, strike it against a hard object such as a rock, or throw it at a water surface. Do not leave the camera in an area subject to vibration. If the camera is subjected to excessive shock, this could result in camera malfunction or damage.
B
Maximum Depth
This camera is designed to withstand water pressure up to a depth of 18 m (59 ft) for approximately 60 minutes. At greater depth, water could seep inside the camera, resulting in camera malfunction.
B
Precautions on Handling the Camera in Cold Locations
• The operation of this camera has been confirmed at temperatures of –10°C (14°F).
If the camera is left with snow or water droplets adhered to the exterior, snow or water droplets between the gaps may become frozen and it may be difficult to operate parts of the camera.
• At temperatures from –10°C to 0°C (14°F to 32°F), the performance of the batteries
(number of images shot and shooting time) will drop temporarily.
• If the camera becomes extremely cold in cold locations, the monitor performance may drop temporarily immediately after the power is turned on (i.e., the monitor appears darker than usual or a residual image occurs).
• When using the camera in cold locations or at high altitudes, keep the camera warm inside a protection against cold or clothing.
B
Handle the Lens and All Moving Parts with Care
Do not apply force to the lens, lens cover, monitor, memory card slot, or battery chamber. These parts are easily damaged. Applying force to the lens cover could result in camera malfunction or damage to the lens.
B
Avoid Sudden Changes in Temperature
Sudden changes in temperature, such as when entering or leaving a heated building on a cold day, can cause condensation to form inside the device. To prevent condensation, place the device in a carrying case or a plastic bag before exposing it to sudden changes in temperature.
Do not expose the camera to high temperatures by leaving it on the beach or in direct sunlight before entering the water.
B
Keep away from Strong Magnetic Fields
Do not use or store this device in the vicinity of equipment that generates strong electromagnetic radiation or magnetic fields. Strong static charge or the magnetic fields produced by equipment such as radio transmitters could interfere with the monitor, damage data saved on the memory card, or affect the product’s internal circuitry.
F 3
F 4
B
Do Not Point the Lens at Strong Light Sources for Extended
Periods
Avoid pointing the lens at the sun or other strong light sources for extended periods when using or storing the camera. Intense light may cause deterioration of the image sensor, producing a white blur effect in photographs.
B
Turn the Product off Before Removing or Disconnecting the Power
Source
Do not remove the battery while the product is on, or while images are being saved or deleted. Forcibly cutting power in these circumstances could result in loss of data or in damage to product memory or internal circuitry.
B
Notes About the Monitor
• Monitors and electronic viewfinders are constructed with extremely high precision; at least 99.99% of pixels are effective, with no more than 0.01% being missing or defective. Hence while these displays may contain pixels that are always lit (white, red, blue, or green) or always off (black), this is not a malfunction and has no effect on images recorded with the device.
• Due to the general characteristics of OLED monitors, prolonged or repeated display of the same screen or image may result in screen burn. Screen burn can be recognized by decreased brightness in portions of the monitor or mottled display.
In some cases, screen burn may become permanent. However, images are in no way affected by screen burn.
To prevent screen burn, do not set monitor brightness higher than necessary and do not display the same screen or image for an extended period of time.
• Images in the monitor may be difficult to see under bright lighting.
• The monitor is lit by an LED backlight. Should the monitor begin to dim or flicker, contact your Nikon-authorized service representative.
The Battery
Be sure to read and follow the warnings in “For Your Safety” ( Avii-ix) before
use.
• Check the battery level before using the camera and replace or charge the battery if necessary. Do not continue charging once the battery is fully charged as this will result in reduced battery performance. Whenever possible, carry a fully charged spare battery when taking images on important occasions.
• Do not use the battery at ambient temperatures below −10°C (14°F) or above 40°C (104°F).
• Charge the battery indoors with an ambient temperature of 5°C to 35°C
(41°F to 95°F) before use.
• When charging the battery inserted into this camera using the charging AC adapter or a computer, the battery is not charged at battery temperatures below 0°C (32°F) or above 45°C (113°F).
• Note that the battery may become hot during use; wait for the battery to cool before charging. Failure to observe these precautions could damage the battery, impair its performance, or prevent it from charging normally.
• On cold days, the capacity of batteries tends to decrease. If an exhausted battery is used at a low temperature, the camera will not turn on. Be sure that the battery is fully charged before heading outside to take images in cold weather. Keep spare batteries in a warm place and exchange as necessary. Once warmed, a cold battery may recover some of its charge.
• Dirt on the battery terminals can prevent the camera from functioning.
Should the battery terminals become dirty, wipe them off with a clean, dry cloth before use.
• If the battery will not be used for some time, insert it in the camera and completely exhaust it before removing it for storage. The battery should be stored in a cool location with an ambient temperature of 15°C to 25°C (59°F to 77°F). Do not store the battery in hot or extremely cold locations.
• Always remove the battery from the camera or optional battery charger when it is not being used. When inserted, minute amounts of current are drawn from the battery even when not in use. This may result in excessive draining of the battery and complete loss of function. Turning the camera on or off while the battery is exhausted can result in reduced battery life.
• Recharge the battery at least once every six months and completely exhaust it before returning it to storage.
• After removing the battery from the camera or optional battery charger, put the battery in a plastic bag, etc. to insulate the terminal and store it in a cool place.
• A marked drop in the time a fully-charged battery retains its charge, when used at room temperature, indicates that the battery needs to be replaced.
Purchase a new EN-EL12 battery.
• Replace the battery when it no longer holds a charge. Used batteries are a valuable resource. Please recycle used batteries in accordance with local regulations.
Charging AC Adapter
Be sure to read and follow the warnings in “For Your Safety” ( Avii-ix) before
use.
• The Charging AC Adapter EH-71P is for use only with compatible devices. Do not use with another make or model of device.
• Do not use a USB cable other than the UC-E21. Using a USB cable other than the UC-E21 could result in overheating, fire or electric shock.
F 5
F 6
• Do not, under any circumstances, use another make or model of AC adapter other than Charging AC Adapter EH-71P, and do not use a commercially available USB-AC adapter or a battery charger for a mobile phone. Failure to observe this precaution could result in overheating or in damage to the camera.
• The EH-71P is compatible with AC 100-240 V, 50/60 Hz electrical outlets.
When using in other countries, use a plug adapter (available commercially) as necessary. For more information about plug adapters, consult your travel agency.
Memory Cards
• Use only Secure Digital memory cards. See “Approved Memory Cards”
( F31) for recommended memory cards.
• Observe the precautions noted in the documentation included with your memory card.
• Do not affix labels or stickers to the memory card.
• Do not format the memory card using a computer.
• The first time you insert a memory card that has been used in another device into this camera, be sure to format it with this camera. We recommend formatting new memory cards with this camera before using them with this camera.
• Note that formatting a memory card permanently deletes all images
and other data on the memory card. If there is data saved on the memory card that you wish to keep, copy that data to a computer before formatting.
• If the message Card is not formatted. Format card? is displayed when the camera is turned on, the memory card must be formatted. If there is data on the memory card that you do not want to delete, select No and press the k button. Copy that data to a computer before formatting. To format the memory card, select Yes.
• Observe the following precautions while formatting the memory card, saving and deleting images, and copying images to a computer, otherwise data or the memory card itself may be damaged.
- Do not open the battery-chamber/memory card slot cover or remove the memory card or battery.
- Do not turn off the camera.
- Do not disconnect the AC adapter.
Cleaning and Storage
Cleaning
Do not use alcohol, thinner, or other volatile chemicals.
Lens
Avoid touching glass parts with your fingers. Remove dust or lint with a blower (typically a small device with a rubber bulb attached to one end that is pumped to produce a stream of air out the other end). To remove fingerprints or other stains that cannot be removed with a blower, wipe the lens with a soft cloth, using a spiral motion that starts at the center of them and working toward the edges. If this fails, clean the lens using a cloth lightly dampened with commercial lens cleaner.
Monitor
Remove dust or lint with a blower. To remove fingerprints and other stains, clean the monitor with a soft, dry cloth, being careful not to apply pressure.
Body
Use a blower to remove dust, dirt, or sand, then wipe gently with a soft, dry cloth. If a foreign substance adheres to the waterproof packing inside of the battery-chamber/ memory card slot cover or inside of the battery chamber, remove it with the included brush. After using the camera underwater, or at the beach or other sandy or dusty environment, wipe off any sand, dust, or salt with a dry cloth lightly dampened with fresh water and dry thoroughly.
If you handle the camera using hands where sunscreen lotion is applied, this could cause deterioration of the camera exterior. Note that foreign matter inside the camera could cause damage not covered by the warranty.
C
More Information
See “Notes About Waterproof and Dustproof Performances” ( Axii) and
“Cleaning after Using the Camera Underwater” ( Axv) for more information.
F 7
F 8
Storage
Turn the camera off when not in use. Be sure that the power-on lamp is off before putting the camera away. Remove the battery if the camera will not be used for an extended period. Do not store the camera with naphtha or camphor moth balls, or in any of the following locations:
• Next to equipment that produces strong electromagnetic fields, such as televisions or radios
• Exposed to temperatures below –10°C (14°F) or above 50°C (122°F)
• Places that are poorly ventilated or subject to humidity of over 60%
To prevent mold or mildew, take the camera out of storage at least once a month. Turn the camera on and release the shutter a few times before putting the camera away again.
For storing the battery, follow the precautions in “The Battery” (
F4) in “Caring for the Product” ( F2).
Troubleshooting
If the camera fails to function as expected, check the list of common problems below before consulting your retailer or Nikon-authorized service representative.
Power, Display, Settings Issues
Problem
The camera is on but does not respond.
Battery inserted in the camera cannot be charged.
Camera cannot be turned on.
Cause/Solution
• Wait for recording to end.
• If the problem persists, turn the camera off.
If the camera does not turn off, remove and reinsert the battery or batteries or, if you are using an AC adapter, disconnect and reconnect the AC adapter.
Note that although any data currently being recorded will be lost, data that have already been recorded will not be affected by removing or disconnecting the power source.
• Confirm all connections.
• When connected to a computer, the camera may not charge for any of the reasons described below.
- Off is selected for Charge by computer in the setup menu.
- Battery charging stops if the camera is turned off.
- Battery charging is not possible if the camera’s display language and date and time have not been set, or the date and time were reset after the camera’s clock battery was exhausted. Use the charging
AC adapter to charge the battery.
- Battery charging may stop if the computer is in sleep mode.
- Depending upon the computer specifications, settings, and status, battery charging may not be possible.
• The battery is exhausted.
• The power switch is enabled a few seconds after the battery is inserted. Wait a few seconds before pressing the power switch.
A
–
–
–
–
–
F 9
F 10
Date and time of recording are not correct.
Problem
Camera turns off without warning.
Monitor is blank.
Monitor is hard to read.
Cause/Solution
• The camera automatically turns off to save power (auto off function).
• The camera or battery has become too cold and cannot operate properly.
• The inside of the camera has become hot.
Leave the camera off until the inside of the camera has cooled, and then try turning it on again.
• The camera turns off if the USB cable connecting it to a computer or printer is disconnected. Reconnect the USB cable.
• The camera is off.
• The camera has entered standby mode to save power. Press the power switch, shutter-release button, A button, c button, or b (e movie-record) button.
• The flash lamp flashes while the flash is charging. Wait for the flash to charge.
• The camera and computer are connected via the USB cable.
• The camera and TV are connected via an
HDMI cable.
• Camera and smart device are connected using Wi-Fi connection and the camera is operated by remote control.
• Adjust the monitor brightness.
A
–
• The monitor is dirty. Clean the monitor.
• If the camera clock has not been set, the
“Date not set” indicator flashes during shooting and movie recording. Images and movies saved before the clock is set are dated “00/00/0000 00:00” or “01/01/2014
00:00” respectively. Set the correct time and date from the Time zone and date option in the setup menu.
• The camera clock is not as accurate as ordinary watches or clocks. Periodically compare the time of the camera clock with that of a more accurate timepiece and reset as required.
Problem
No indicators displayed in monitor.
Print date not available.
Date not imprinted on images even when
Print date is enabled.
Screen for setting time zone and date is displayed when camera is turned on.
Camera settings reset.
Cause/Solution
Hide info is selected for Photo info in
Monitor settings in the setup menu.
Time zone and date has not been set in the setup menu.
• The current shooting mode does not support Print date.
• The date cannot be imprinted on movies.
The clock battery is exhausted; all settings were restored to their default values.
Camera becomes hot.
Camera makes sound.
Unable to select a menu
A
The camera may become hot when used for an extended period of time to record movies or send images using an Eye-Fi card, or when used in a hot environment; this is not a malfunction.
Depending on the Autofocus mode setting or the shooting mode, the camera may produce an audible focusing sound.
• Some functions cannot be used with other menu options.
• Some menus are not available when Wi-Fi is connected. Terminate the Wi-Fi connection.
–
Shooting Issues
Problem
Cannot switch to shooting mode.
Cause/Solution
Disconnect the HDMI cable or USB cable.
A
F 11
F 12
Problem
No image captured when the shutterrelease button is pressed.
Camera cannot focus.
Images are blurred.
Cause/Solution
• When the camera is in playback mode, press the A button, the shutter-release button, or the b (e movie-record) button.
• When menus are displayed, press the d button.
• The battery is exhausted.
• When the flash lamp is flashing, the flash is charging.
• The camera and smart device are connected using Wi-Fi connection and the camera is operated by remote control.
• The subject is too close. Try shooting with macro mode, G (easy auto) mode or
Close-up scene mode.
• The subject is hard to focus on.
• Set AF assist in the setup menu to Auto.
• Turn the camera off and then on again.
• Use the flash.
• Increase the ISO sensitivity value.
• Enable vibration reduction or motion detection.
• Use j (Best Shot Selector).
• Use a tripod to stabilize the camera when shooting (using the self-timer at the same time is more effective).
A
Bright specks appear in images captured with flash.
Flash does not fire.
The flash is reflecting off particles in the air. Set the flash mode setting to W (off).
• The flash mode is set to W (off).
• A shooting mode that restricts the flash is selected.
• On is selected for Blink proof in the smart portrait menu.
• On is selected for Smile timer in the smart portrait menu.
• A function that restricts the flash is enabled.
Problem
Digital zoom cannot be used.
Image mode not available.
No sound when shutter is released.
AF-assist illuminator does not light.
Images appear smeared.
Colors are unnatural.
Randomly spaced bright pixels (“noise”) appear in image.
Cause/Solution
• Digital zoom is set to Off in the setup menu.
• Digital zoom cannot be used in the following situations.
- When the scene mode is Portrait, Night
portrait, Night landscape,
Backlighting (when HDR is o), Easy
panorama, Pet portrait, or
Underwater.
- When smart portrait mode is selected
- When Continuous in the shooting menu is set to Multi-shot 16
- When AF area mode in the shooting menu is set to Subject tracking
• Other functions that restrict the use of digital zoom are set.
A
A function that restricts the Image mode option is enabled.
Off is selected for Sound settings > Shutter
sound in the setup menu. No sound is produced with some shooting modes and settings, even when On is selected.
Off is selected for the AF assist option in the setup menu. AF-assist illuminator may not light depending on the position of the focus area or the current scene mode, even when
Auto is selected.
The lens is dirty. Clean the lens.
White balance or hue is not adjusted properly.
The subject is dark, and the shutter speed is too slow or ISO sensitivity is too high. Noise can be reduced by:
• Using the flash.
• Specifying a lower ISO sensitivity setting.
F 13
F 14
Problem
Images are too dark
(underexposed).
Cause/Solution
• The flash mode is set to W (off).
• The flash window is blocked.
• The subject is beyond the range of the flash.
• Adjust exposure compensation.
• Increase ISO sensitivity.
• The subject is backlit. Set the scene mode to Backlighting with HDR set to k, or set the flash mode to X (fill flash).
A
Images are too bright
(overexposed).
Adjust exposure compensation.
Unexpected results when flash set to V
(auto with red-eye reduction).
Skin tones are not softened.
Saving images takes time.
When taking images with V (auto with redeye reduction), In-Camera Red Eye Fix may be applied to areas not affected by red-eye in rare cases. Use any shooting mode other than
Night portrait, and change the flash mode to any setting other than V (auto with redeye reduction) and try taking an image again.
• In some shooting conditions, facial skin tones may not be softened.
• For images containing four or more faces, try using the Skin softening effect in
Glamour retouch in the playback menu.
It may take more time to save images in the following situations.
• When the noise reduction function is in operation, such as when shooting in a dark environment
• When the flash mode is set to V (auto with red-eye reduction)
• When taking images in the following scene modes
- Hand-held in Night portrait
- Hand-held in Night landscape
- HDR set to o in Backlighting
- Easy panorama
• When the skin softening function is applied while shooting
• When using continuous shooting mode
–
Problem
A ring-shaped belt or rainbow-colored stripe appears in the monitor or images.
Cause/Solution
When shooting with backlighting or when a very strong light source (such as sunlight) is in the frame, a ring-shaped belt or rainbowcolored stripe (ghosting) may occur. Change the position of the light source, or frame the image so that the light source does not enter the frame, and try again.
Playback Issues
Problem
File cannot be played back.
Cannot zoom in on image.
Cannot record voice memos.
Cannot edit image.
A
–
Cause/Solution
• This camera may not be able to play back images saved with another make or model of digital camera.
• This camera cannot play back movies recorded with another make or model of digital camera.
• This camera may not be able to play back data edited on a computer.
• Playback zoom cannot be used with movies.
• When zooming in on a small-sized image, the zoom ratio shown on the screen may differ from the actual zoom ratio of the image.
• This camera may not be able to zoom in on images captured with another make or model of digital camera.
• Voice memos cannot be attached to movies.
• Voice memos cannot be attached to images captured with other cameras. Voice memos attached to images using another camera cannot be played back on this camera.
• Some images cannot be edited. Images that have already been edited may not be edited again.
• There is not enough free space in the internal memory or on the memory card.
• This camera is unable to edit images captured with other cameras.
• Editing functions used for images are not available for movies.
A
–
–
–
–
–
F 15
F 16
Problem
Cannot rotate image.
Images are not displayed on TV.
Nikon Transfer 2 does not start when camera is connected to a computer.
The PictBridge startup screen is not displayed when the camera is connected to a printer.
Images to be printed are not displayed.
Cannot select paper size with camera.
Cause/Solution
• This camera cannot rotate images captured with another make or model of digital camera.
• Images edited using Data imprint cannot be rotated.
• HDMI is not correctly set in the TV
settings setup menu.
• A computer or printer is connected to the camera.
• The memory card contains no images.
Replace the memory card. Remove the memory card to play back images from the internal memory.
• The camera is off.
• The battery is exhausted.
• The USB cable is not correctly connected.
• The camera is not recognized by the computer.
• The computer is not set to start Nikon
Transfer 2 automatically. For more information about Nikon Transfer 2, refer to help information contained in ViewNX 2.
With some PictBridge-compatible printers, the
PictBridge startup screen may not be displayed and it may be impossible to print images when Auto is selected for the Charge
by computer option in the setup menu. Set the Charge by computer option to Off and reconnect the camera to the printer.
• The memory card contains no images.
Replace the memory card.
• Remove the memory card to print images from the internal memory.
The camera cannot be used to select the paper size in the following situations, even when printing from a PictBridge-compatible printer. Use the printer to select the paper size.
• The printer does not support the paper sizes specified by the camera.
• The printer automatically selects the paper size.
A
–
–
–
Location Data Functions
Problem
Unable to identify the location or it takes time to identify the location.
Cause/Solution
• The camera may not be able to identify the location in some shooting environments. To use the location data functions, use the camera as much as possible in an open-air area.
• When positioning for the first time or when positioning was unable to be performed for about two hours, it takes a few minutes to obtain the location data.
A
Unable to record location data on shot images.
Difference between the actual shooting location and recorded location data.
When z or y is displayed on the shooting screen, the location data is not recorded.
Before shooting images, check the location data reception.
The acquired location data may deviate in some shooting environments. When there is a significant difference in the signals from the positioning satellites, there could be a deviation of up to several hundred meters.
The recorded location name is different from the intended one or is not displayed.
The desired landmark name may not be registered, or a different landmark name may be registered.
–
Unable to update the
A-GPS file.
Unable to display the map.
Unable to turn off the altimeter or depth gauge.
• Check the following items.
- Whether the memory card is inserted
- Whether the A-GPS file is stored on the memory card
- Whether the A-GPS file saved on the memory card is more recent than the A-
GPS file saved in the camera
- Whether the A-GPS file is still valid
• The A-GPS file may be corrupted. Download the file from the website once more.
–
– Maps cannot be displayed while the camera is being charged with the charging AC adapter, even if the U (map) button is pressed.
When Altimeter/depth gauge of Altitude/
depth options in the Location data options menu is set to On, the altimeter or depth gauge is always displayed regardless of
Monitor settings in the setup menu.
To turn off the altimeter or depth gauge, set the Altimeter/depth gauge to Off.
F 17
F 18
Problem
The altimeter or depth gauge and atmospheric pressure icon remain displayed on the shooting screen.
Set Photo info of Monitor settings in the setup menu to Hide info.
Unable to display the altimeter or depth gauge even when
Altimeter/depth
gauge is set to On.
Even when Altimeter/depth gauge is set to
On, the altimeter or depth gauge is not displayed in the following situations.
• When the shutter-release button is pressed halfway
• During shooting in the Easy panorama scene mode
• During movie recording
• When a subject is registered using Subject
tracking of AF area mode
• When a message is being displayed
Water depth shows 0 m
Unable to select Use
location data of Alt./
depth correction in the Location data options menu.
The water depth will be displayed as 0 m if the camera is not submerged under water when the Underwater scene mode is selected.
• Record location data in the Location data options menu is set to Off.
• You cannot select this function unless signals are received from four or more satellites and positioning has been performed.
• The camera is submerged under water. You cannot select this function during underwater shooting.
–
–
–
Unable to select
Create log in the
Location data options menu.
Clock not set.
Cause/Solution
Set date and time.
A
Unable to select Start
all logs or Start
location log.
• Record location data in the Location data options menu is set to Off.
• The camera is recording log data. To record a new log, select End all logs or End
location log, and end the log currently being recorded.
Unable to save log data.
Problem
Unable to display the water depth log as a graph
Cause/Solution
• Make sure that a memory card is inserted in the camera.
• Up to 36 log data events for location data logs can be recorded per day whereas up to
34 log data events each for altitude logs and water depth logs can be recorded per day.
• The total number of log data events that can be saved on a single memory card is 200, which includes up to 100 log data events for location data logs and up to 100 log data events for a combined total of altitude logs and water depth logs. Delete log data that is no longer required from a memory card or replace the memory card with a new one.
A
–
–
Log files are created but are not displayed as graphs if you selected Start depth log but did not submerge the camera under water.
Wi-Fi
Problem Cause/Solution
SSID (network name) of the camera is not displayed on the smart device.
Select Connect to smart device in the Wi-Fi options menu on the camera to enter connection standby mode.
Turn off the Wi-Fi function of the smart device and then turn it on again.
A
F 19
USER LICENSE AGREEMENT FOR MAP DATA
AND LOCATION NAME DATA
The map data and location name data that are stored in this digital camera (“Data”) is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms and conditions which are agreed to by you, on the one hand, and Nikon Corporation (“Nikon”) and its licensors (including their licensors and suppliers) on the other hand.
Terms and Conditions
F 20
Personal Use Only. You agree to use this Data together with this digital camera and the image data taken by the digital camera for the solely personal, non-commercial purposes for which you were licensed, and not for service bureau, time-sharing or other similar purposes.
Accordingly, but subject to the restrictions set forth in the following paragraphs, you agree not to otherwise reproduce, copy, modify, decompile, disassemble or reverse engineer any portion of this Data, and may not transfer or distribute it in any form, for any purpose, except to the extent permitted by mandatory laws.
Restrictions. Except where you have been specifically licensed to do so by Nikon, and without limiting the preceding paragraph, you may not (a) use this Data with any products, systems, or applications installed or otherwise connected to or in communication with vehicles, capable of vehicle navigation, positioning, dispatch, real time route guidance, fleet management or similar applications; or (b) with or in communication with any positioning devices or any mobile or wireless-connected electronic or computer devices, including without limitation cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or PDAs.
Warning. The Data may contain inaccurate or incomplete information due to the passage of time, changing circumstances, sources used and the nature of collecting comprehensive geographic data, any of which may lead to incorrect results.
No Warranty. This Data is provided to you “as is,” and you agree to use it at your own risk. Nikon and its licensors (and their licensors and suppliers) make no guarantees, representations or warranties of any kind, express or implied, arising by law or otherwise, including but not limited to, content, quality, accuracy, completeness, effectiveness, reliability, fitness for a particular purpose, usefulness, use or results to be obtained from this Data, or that the Data or server will be uninterrupted or errorfree.
Disclaimer of Warranty: NIKON AND ITS LICENSORS (INCLUDING THEIR LICENSORS
AND SUPPLIERS) DISCLAIM ANY WARRANTIES, EXPRESS OR IMPLIED, OF QUALITY,
PERFORMANCE, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-
INFRINGEMENT. Some States, Territories and Countries do not allow certain warranty exclusions, so to that extent the above exclusion may not apply to you.
Disclaimer of Liability: NIKON AND ITS LICENSORS (INCLUDING THEIR LICENSORS
AND SUPPLIERS) SHALL NOT BE LIABLE TO YOU: IN RESPECT OF ANY CLAIM, DEMAND
OR ACTION, IRRESPECTIVE OF THE NATURE OF THE CAUSE OF THE CLAIM, DEMAND
OR ACTION ALLEGING ANY LOSS, INJURY OR DAMAGES, DIRECT OR INDIRECT, WHICH
MAY RESULT FROM THE USE OR POSSESSION OF THE INFORMATION; OR FOR ANY
LOSS OF PROFIT, REVENUE, CONTRACTS OR SAVINGS, OR ANY OTHER DIRECT,
INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF
YOUR USE OF OR INABILITY TO USE THIS INFORMATION, ANY DEFECT IN THE
INFORMATION, OR THE BREACH OF THESE TERMS OR CONDITIONS, WHETHER IN AN
ACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY, EVEN IF NIKON OR ITS
LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some
States, Territories and Countries do not allow certain liability exclusions or damages limitations, so to that extent the above may not apply to you.
Export Control. You agree not to export from anywhere any part of the Data or any direct product thereof except in compliance with, and with all licenses and approvals required under, applicable export laws, rules and regulations, including but not limited to the laws, rules and regulations administered by the Office of Foreign Assets
Control of the U.S. Department of Commerce and the Bureau of Industry and Security of the U.S. Department of Commerce. To the extent that any such export laws, rules or regulations prohibit Nikon and its licensors from complying with any of its obligations hereunder to deliver or distribute Data, such failure shall be excused and shall not constitute a breach of this Agreement.
Entire Agreement. These terms and conditions constitute the entire agreement between Nikon (and its licensors, including their licensors and suppliers) and you pertaining to the subject matter hereof, and supersedes in their entirety any and all written or oral agreements previously existing between us with respect to such subject matter.
Governing Law. The above terms and conditions shall be governed by the laws of the Japan, without giving effect to (i) its conflict of laws provisions, or (ii) the United
Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded; provided that in the event that the laws of the Japan is not deemed applicable to this Agreement for any reason in the country where you obtained the Data, this Agreement shall be governed with the laws of the country where you obtained the Data. You agree to submit to the jurisdiction of Japan for any and all disputes, claims and actions arising from or in connection with the Data provided to you hereunder.
F 21
F 22
Government End Users. If the Data supplied by HERE is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, the Data is a
"commercial item" as that term is defined at 48 C.F.R. ("FAR") 2.101, is licensed in accordance with the End-User Terms under which this Data was provided, and each copy of the Data delivered or otherwise furnished shall be marked and embedded as appropriate with the following "Notice of Use," and shall be treated in accordance with such Notice:
NOTICE OF USE
CONTRACTOR (MANUFACTURER/ SUPPLIER) NAME:
HERE
CONTRACTOR (MANUFACTURER/ SUPPLIER) ADDRESS:
425 West Randolph Street, Chicago, Illinois 60606
This Data is a commercial item as defined in
FAR 2.101 and is subject to the End-User
Terms under which this Data was provided.
© 2013 HERE - All rights reserved.
If the Contracting Officer, federal government agency, or any federal official refuses to use the legend provided herein, the Contracting Officer, federal government agency, or any federal official must notify HERE prior to seeking additional or alternative rights in the Data.
Notices related to licensed software copyright holders.
• Map data and location name data for Japan
© 2013 ZENRIN CO., LTD. All rights reserved.
This service uses map and POI data of ZENRIN CO., LTD.
“ZENRIN” is a registered trademark of ZENRIN CO., LTD.
• Map data and location name data except for Japan
© 1987-2013 HERE
All rights reserved.
Austria
Croatia
Cyprus
Estonia
Latvia
Lithuania
Moldova
Poland
Slovenia
Ukraine
France
Germany
Great Britain
© Bundesamt für Eich- und Vermessungswesen
© EuroGeographics source: © IGN 2009 - BD TOPO ®
Die Grundlagendaten wurden mit Genehmigung der zuständigen Behörden entnommen
Contains Ordnance Survey data © Crown copyright and database right 2010
Contains Royal Mail data © Royal Mail copyright and database right 2010
F 23
F 24
Greece
Hungary
Italy
Norway
Portugal
Spain
Sweden
Switzerland
United
Kingdom
Canada
Mexico
United States
Australia
Nepal
Sri Lanka
Copyright Geomatics Ltd.
Copyright © 2003; Top-Map Ltd.
La Banca Dati Italiana è stata prodotta usando quale riferimento anche cartografia numerica ed al tratto prodotta e fornita dalla
Regione Toscana.
Copyright © 2000; Norwegian Mapping Authority
Source: IgeoE - Portugal
Información geográfica propiedad del CNIG
Based upon electronic data © National Land Survey Sweden.
Topografische Grundlage: © Bundesamt für Landestopographie
Contains public sector information licensed under the Open
Government Licence v1.0 (see for the license http://www.nationalarchives.gov.uk/doc/open-governmentlicence/)
Adapted from data from the office for National Statistics licensed under the Open Government Licence v.1.0
This data includes information taken with permission from
Canadian authorities, including © Her Majesty, © Queen’s Printer for Ontario, © Canada Post, GeoBase ® , © Department of
Natural Resources Canada. All rights reserved.
Fuente: INEGI (Instituto Nacional de Estadística y Geografía.)
© United States Postal Service ® 2013. Prices are not established, controlled or approved by the United States Postal
Service ® . The following trademarks and registrations are owned by the USPS: United States Postal Service, USPS, and
ZIP+4.
Copyright. Based on data provided under license from PSMA
Australia Limited (www.psma.com.au).
Product incorporates data which is © 2013 Telstra Corporation
Limited, Intelematics Australia Pty Ltd and HERE International
LLC.
Copyright © Survey Department, Government of Nepal.
This product incorporates original source digital data obtained from the Survey Department of Sri Lanka
© 2009 Survey Department of Sri Lanka
The data has been used with the permission of the Survey
Department of Sri Lanka
Israel
Jordan
Mozambique
© Survey of Israel data source
© Royal Jordanian Geographic Centre.
Certain Data for Mozambique provided by Cenacarta © 2013 by
Cenacarta
Nicaragua
Réunion
Ecuador
The Pacific Ocean and Caribbean Sea maritime borders have not been entirely defined.
Northern land border defined by the natural course of the Coco
River (also known as Segovia River or Wangki River) corresponds to the source of information available at the moment of its representation.
source: © IGN 2009 - BD TOPO ®
INSTITUTO GEOGRAFICO MILITAR DEL ECUADRO
AUTORIZACION N° IGM-2011-01- PCO-01 DEL 25 DE ENERO DE
2011
Guadeloupe
Guatemala source: © IGN 2009 - BD TOPO ®
Aprobado por el INSTITUTO GEOGRAFICO NACIONAL -
Resolución del IGN N° 186-2011
French Guiana source: © IGN 2009 - BD TOPO ®
Martinique source: © IGN 2009 - BD TOPO ®
F 25
Specifications
Nikon COOLPIX AW120 Digital Camera
F26
Type Compact digital camera
Number of effective pixels
Image sensor
Lens
Focal length f/-number
Construction
Monitor
Frame coverage
(shooting mode)
Frame coverage
(playback mode)
Storage
16.0 million
1/2.3-in. type CMOS; approx. 16.76 million total pixels
NIKKOR lens with 5× optical zoom
4.3-21.5 mm (angle of view equivalent to that of 24-
120 mm lens in 35mm [135] format) f/2.8-4.9
12 elements in 10 groups (2 ED lens elements)
Digital zoom magnification
Vibration reduction
Up to 4× (angle of view equivalent to that of approx.
480 mm lens in 35mm [135] format)
Combination of lens shift and electronic VR
Motion blur reduction Motion detection (still pictures)
Autofocus (AF)
Focus range
Contrast-detect AF
• [W]: Approx. 50 cm (1 ft 8 in.) -
,
[T]: Approx. 50 cm (1 ft 8 in.) -
• Macro mode: Approx. 1 cm (0.4 in.) -
(wide-angle position)
(All distances measured from center of front surface of lens)
Focus-area selection
Face priority, manual with 99 focus areas, center, subject tracking, target finding AF
7.5 cm (3-in.), approx. 921k-dot, OLED monitor with antireflection coating and 5-level brightness adjustment
Approx. 98% horizontal and 98% vertical (compared to actual picture)
Approx. 100% horizontal and 100% vertical (compared to actual picture)
Media
File system
File formats
Internal memory (approx. 329 MB)
SD/SDHC/SDXC memory card
DCF, Exif 2.3, and DPOF compliant
Still pictures: JPEG
Sound files (voice memo): WAV
Movies: MOV (video: H.264/MPEG-4 AVC, Audio: LPCM stereo)
Image size (pixels)
ISO sensitivity
(Standard output sensitivity)
Exposure
Metering mode
Exposure control
Shutter
Speed
• 16M (High) 4608×3456P
• 16M 4608×3456
• 8M
• 4M
• 2M
• VGA
• 16:9 12M
• 1:1
3264×2448
2272×1704
1600×1200
640×480
4608×2592
3456×3456
• ISO 125 - 1600
• ISO 3200, 6400 (available when using Auto mode)
Matrix, center-weighted (digital zoom less than 2×), spot
(digital zoom 2× or more)
Programmed auto exposure and exposure compensation (–2.0 - +2.0 EV in steps of
1
/ 3 EV)
Mechanical and CMOS electronic shutter
• 1/1500 - 1 s
• 1/4000 s (maximum speed during high-speed continuous shooting)
• 4 s (Fireworks show scene mode)
Electronically-controlled preset aperture (–1 AV) and ND filter (–2 AV) selections
3 steps (f/2.8, f/4.1, f/8.2 [W])
Can be selected from 10 s and 2 s
Aperture
Range
Self-timer
Flash
Range (approx.)
(ISO sensitivity:
Auto)
Flash control
Interface
Data transfer protocol
HDMI output
I/O terminal
[W]: 0.5 - 5.2 m (1 ft 8 in. - 17 ft)
[T]: 0.5 - 4.5 m (1 ft 8 in. - 14 ft)
TTL auto flash with monitor preflashes
Hi-Speed USB equivalent
MTP, PTP
Can be selected from Auto, 480p, 720p, and 1080i
• Micro-USB connector
• HDMI micro connector (Type D) (HDMI output)
F 27
F 28
Wi-Fi (Wireless LAN)
Standards
Communications protocols
IEEE 802.11b/g/n (standard wireless LAN protocol)
ARIB STD-T66 (standard for low power data communication systems)
IEEE 802.11b: DBPSK/DQPSK/CCK
IEEE 802.11g: OFDM
IEEE 802.11n: OFDM
Range (line of sight) Approx. 30 m (32 yd)
Operating frequency
2412 - 2462 MHz (1 - 11 channels)
Data rates (actual measured values)
Security
Access protocols
Electronic compass
Location data
Barometer
Altimeter
Depth gauge
Supported languages
Power sources
Charging time
IEEE 802.11b: 5 Mbps
IEEE 802.11g: 17 Mbps
IEEE 802.11n: 17 Mbps
OPEN/WPA2
CSMA/CA
16 cardinal points (position correction using 3-axis acceleration sensor, automatic correction for the deviated angle, and automatic offset adjustment)
• GPS
Receiving frequency: 1575.42 MHz
Geodetic system: WGS 84
• GLONASS
Receiving frequency: 1598.0625 - 1605.3750 MHz
Geodetic system: WGS 84
Operating range: Approx. 500 - 1100 hPa
Operating range: Approx. −300 - +4500 m (−984 -
+14,760 ft)
Operating range: Approx. 0 - 20 m (0 - 65 ft)
Arabic, Bengali, Bulgarian, Chinese (Simplified and
Traditional), Czech, Danish, Dutch, English, Finnish,
French, German, Greek, Hindi, Hungarian, Indonesian,
Italian, Japanese, Korean, Marathi, Norwegian, Persian,
Polish, Portuguese (European and Brazilian), Romanian,
Russian, Serbian, Spanish, Swedish, Tamil, Telugu, Thai,
Turkish, Ukrainian, Vietnamese
One Rechargeable Li-ion Battery EN-EL12 (included)
AC Adapter EH-62F (available separately)
Approx. 2 h 20 min (when using Charging AC Adapter
EH-71P and when no charge remains)
Battery life
1
Still pictures
Movies (actual battery life for recording) 2
Tripod socket
Dimensions
(W × H × D)
Weight
Approx. 350 shots when using EN-EL12
Approx. 1 h 15 min (1080/30p) when using EN-EL12
Approx. 1 h 20 min (1080/25p) when using EN-EL12
1/4 (ISO 1222)
Approx. 110.1 × 66.0 × 25.8 mm (4.4 × 2.6 × 1.1 in.)
(excluding projections)
Approx. 213 g (7.5 oz) (including battery and SD memory card)
Operating environment
Temperature
Humidity
Waterproof
Dustproof
Shockproof
−10°C - +40°C (14°F - 104°F) (land)
0°C - 40°C (32°F - 104°F) (underwater)
85% or less (no condensation)
JIS/IEC protection class 8 (IPX8) equivalent (under our testing conditions)
Capacity to shoot images underwater up to a depth of
18 m (59 ft) and for 60 minutes
JIS/IEC protection class 6 (IP6X) equivalent (under our testing conditions)
Cleared our testing conditions
3
compliant with MIL-STD
810F Method 516.5-Shock
• Unless otherwise stated, all figures assume a fully-charged battery and an ambient temperature of 23 ±3°C (73.4 ±5.4°F) as specified by the Camera and Imaging Products Association (CIPA).
1
2
3
Battery life may vary depending on conditions of use, such as the interval between shots or the length of time that menus and images are displayed.
Individual movie files cannot exceed 4 GB in size or 29 minutes in length.
Recording may end before this limit is reached if camera temperature becomes elevated.
Dropped from a height of 202 cm (6 ft 6 in.) onto a surface of 5 cm (2 in.) thick plywood (changes in appearance, such as paint peeling off and deformation of the drop shock portion and waterproof performance are not subject to the test).
These tests do not guarantee that the camera will be free from damage or trouble under all conditions.
F 29
F 30
Rechargeable Li-ion Battery EN-EL12
Type
Rated capacity
Rechargeable lithium-ion battery
DC 3.7 V, 1050 mAh
Operating temperature 0°C - 40°C (32°F - 104°F)
Dimensions (W × H × D) Approx. 32 × 43.8 × 7.9 mm (1.3 × 1.7 × 0.3 in.)
Weight Approx. 22.5 g (0.8 oz)
Charging AC Adapter EH-71P
Rated input AC 100 V–240 V, 50/60 Hz, MAX 0.2 A
Rated output DC 5.0 V, 1.0 A
Operating temperature 0°C - 40°C (32°F - 104°F)
Dimensions (W × H × D)
Weight
Approx. 55 × 22 × 54 mm (2.2 × 0.9 × 2.2 in.) (excluding plug adapter)
For Argentina: Approx. 55 × 63 × 59 mm (2.2 × 2.5 ×
2.4 in.)
For Brazil: Approx. 55 × 67 × 59 mm (2.2 × 2.7 × 2.4 in.)
Approx. 48 g (1.7 oz) (excluding plug adapter)
For Argentina: Approx. 73 g (2.6 oz)
For Brazil: Approx. 70 g (2.5 oz)
B
Specifications
• Nikon will not be held liable for any errors this manual may contain.
• The appearance of this product and its specifications are subject to change without notice.
Approved Memory Cards
The following Secure Digital (SD) memory cards have been tested and approved for use in this camera.
• Memory cards with an SD Speed Class rating of 6 or faster are recommended for recording movies. When using a memory card with a lower Speed Class rating, movie recording may stop unexpectedly.
SanDisk
SD memory card
2 GB
1
TOSHIBA
Panasonic 2 GB
1
–
SDHC memory card
4 GB, 8 GB, 16 GB, 32 GB
4 GB, 8 GB, 16 GB, 32 GB
4 GB, 8 GB, 16 GB, 32 GB
2
SDXC memory card
64 GB, 128 GB
64 GB
64 GB
3
Lexar – 4 GB, 8 GB, 16 GB, 32 GB 64 GB, 128 GB
1
If the memory card will be used with a card reader or similar device, make sure that the device supports 2 GB cards.
2
SDHC compliant.
If the memory card will be used with a card reader or similar device, make sure that the device supports SDHC.
3
SDXC compliant.
If the memory card will be used with a card reader or similar device, make sure that the device supports SDXC.
• Contact the manufacturer for details on the above cards. We cannot guarantee camera performance when using memory cards made by other manufacturers.
F 31
F 32
AVC Patent Portfolio License
This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC standard (“AVC video”) and/or (ii) decode AVC video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to provide AVC video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, L.L.C.
See http://www.mpegla.com.
FreeType License (FreeType2)
Portions of this software are copyright © 2012 The FreeType Project
(http://www.freetype.org). All rights reserved.
MIT License (HarfBuzz)
Portions of this software are copyright © 2014 The HarfBuzz Project
(http://www.freedesktop.org/wiki/Software/HarfBuzz). All rights reserved.
Trademark Information
• Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Mac, OS X, the iFrame logo and the iFrame symbol are trademarks or registered trademarks of Apple Inc., in the U.S. and other countries.
• Adobe and Acrobat are registered trademarks of Adobe Systems Inc.
• SDXC, SDHC and SD Logos are trademarks of SD-3C, LLC.
• PictBridge is a trademark.
• HDMI, HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• Wi-Fi and the Wi-Fi logo are trademarks or registered trademarks of the Wi-Fi
Alliance.
• Android and Google Play are trademarks or registered trademarks of Google,
Inc.
• All other trade names mentioned in this manual or the other documentation provided with your Nikon product are trademarks or registered trademarks of their respective holders.
F 33
F 34
Index
Symbols
V Action Button............................. 2, 4
A Auto mode.......................... 24, 45
F Auto sort mode........................ E9
l Delete button...... 31, 75, E51
G Easy Auto Mode ........................... 33
o Exposure compensation.......... 52
h Favorite pictures mode....... E5
m Flash mode ....................................... 48
j Help....................................................... 35
C List by date mode................. E10
p Macro mode .................................... 51
U Map button ...................................... 82
d Menu button
...................... 6, 55, 67, 73, 76, 87
b (e movie-record) button
................................................................. 2, 69
c Playback button ........................... 30 c Playback mode.............................. 30
i Playback zoom ................................. 65
C Scene mode .................................... 35
n Self-timer............................................ 50
z Setup menu................... 76, E62
F Smart portrait mode................. 44
R Special effects mode ................. 42
g (Telephoto)......................................... 27
h Thumbnail playback................. 66
f (Wide-angle).................................... 27
A Shooting mode button... 2, 24
.JPG....................................................... E99
.MOV.................................................... E99
.WAV .................................................... E99
A
AC adapter ......................... 92, E101
Action button .................................... 2, 4
Action control........................................... 4
Action control response
...................................................... 77, E71
AF area mode
....................... 56, 73, E38, E58
AF-assist illuminator
.............................................. 1, 76, E69
A-GPS File .............................. 87, E79
Album.................................................... E5
Altimeter ................................................... 86
Altitude log.............................................. 88
Altitude/depth options
..................................................... 88, E91
Aperture value....................................... 29
Atmospheric pressure ...................... 86
Auto flash ................................................. 49
Autofocus
....................... 56, 73, E41, E59
Auto mode ................................... 24, 45
Auto off........................ 23, 77, E72
Auto sort mode ............................... E9
Auto with red-eye reduction ....... 49
B
Backlighting o........................... 35, 38
Battery ................................... 12, 14, 20
Battery charger................. 15, E101
Battery latch............................................. 12
Battery level indicator....................... 22
Battery-chamber/memory card slot
cover................................................... 12, 16
Beach Z.................................................... 35
Best Shot Selector ............ 38, E35
Black and white copy n....... 35, 38
Blink proof............................. 57, E44
Blink warning...................... 77, E76
Brightness ............................. 76, E65
BSS............................................. 38, E35
Button sound................................. E70
C
Calculate distance ............ 87, E81
Calendar display .................................. 66
Charge by computer ..... 77, E75
Charge lamp............................................ 15
Charger.................................. 15, E101
Charging AC Adapter ........................ 14
Choose key picture
................................... 68, E11, E53
Close-up k .................................. 35, 37
Compression ratio ...................... E30
Computer....................................... 93, 95
Continuous .......................... 56, E34
Copying images................ 67, E52
Create log ............................. 88, E83
Crop..................................................... E20
Cross process o................................. 42
D
Data imprint ......................... 67, E18
Date and time .......... 18, 76, E63
Date format........................... 19, E63
Daylight saving time
........................................... 19, 20, E63
Delete.......... 31, 75, E12, E51
Depth gauge.......................................... 86
Depth log................................................. 88
Digital zoom............. 27, 76, E70
Direct print ........................... 93, E22
Displaying maps ................................... 82
Distance units..................... 87, E80
D-Lighting ............................. 67, E15
DPOF print ....................................... E27
DSCN .................................................. E99
Dusk/dawn i........................................ 35
E
Easy panorama p.... 35, 39, E2
Easy panorama playback
........................................................ 39, E4
Electronic compass ........ 88, E89
Exposure compensation................. 52
Extension ......................................... E99
Eye-Fi upload ...................... 77, E77
Eyelet for camera strap ................. 1, 2
F
Face detection ...................................... 62
Face priority
....................... 62, 73, E38, E58
Favorite pictures .................. 68, E5
Favorite pictures mode............... E5
File name ......................................... E99
Fill flash ...................................................... 49
Fireworks show m.................... 35, 38
Firmware version .............. 77, E78
Fixed range auto.......................... E37
Flash...................................................... 1, 48
Flash lamp........................................ 2, 48
Flash mode................................... 48, 49
Flash off ..................................................... 49
Focus
............ 28, 56, 73, E38, E58
Focus area ................................................ 28
Focus indicator ........................................ 9
Focus lock ................................................ 64
Food u............................................. 35, 37
Format internal memory
..................................................... 77, E73
F 35
F 36
Format memory cards
........................................... 17, 77, E73
Formatting ................. 17, 77, E73
Frame rate.............................. 73, E61
FSCN.................................................... E99
Full-frame playback ............................ 65
Full-time AF ...... 73, E41, E59
G
Glamour retouch............... 67, E17
H
HDMI ................................................... E74
HDMI cable ........................... 93, E21
HDMI connector cover ......................... 1
HDMI device control................. E74
HDR............................................................... 38
Help .............................................................. 35
High key G............................................. 42
High-contrast monochrome F
........................................................................ 42
High-speed continuous.......... E34
HS movie ............ 73, E55, E56
I
Identifier............................................ E99
Image copy .......................... 67, E52
Image mode........................ 56, E30
Image review ...................... 76, E65
Image size............................. 56, E30
Imprinting date and time
.......................................... 20, 76, E67
Internal memory......................... 17, 22
Internal memory indicator ...... 9, 11
ISO sensitivity...................... 56, E37
L
Landscape c......................................... 35
Language .............................. 77, E74
Lens.................................. 1, F7, F26
List by date mode ....................... E10
Location data options ...................... 87
Low key H .............................................. 42
M
Macro mode ............................................ 51
Map actions.......................... 77, E72
Map display............................................. 82
Memory capacity................................. 22
Memory card........................................... 16
Memory card slot.................................. 16
Microphone ................................................ 1
Micro-USB connector
.......................................... 92, 95, E23
Monitor ........................................... 8, F7
Monitor settings................ 76, E65
Motion detection ............ 76, E69
Movie editing...................... 75, E28
Movie length ............................... 69, 70
Movie light............................ 73, E60
Movie menu ........................ 73, E54
Movie options..................... 73, E54
Movie playback..................................... 74
Movie recording................................... 69
Movie VR ................................ 73, E60
Multi selector ...................... 6, 30, 47
Multi-shot 16 .................................. E35
Museum l................................... 35, 38
N
Night landscape j.................. 35, 37
Night portrait e........................ 35, 36
Nikon Transfer 2.................................... 95
Nostalgic sepia E.............................. 42
Number of exposures remaining
...................................................... 22, E31
O
Open with HS footage
.................................. 73, E56, E58
Optical zoom .......................................... 27
Optional accessories ............... E101
P
Paper size ...................... E25, E26
Party/indoor f.......................... 35, 36
Pet portrait auto release ................. 40
Pet portrait O............................. 35, 40
Photo info ............................. 76, E65
Photo VR ................................ 76, E68
PictBridge.............................. 93, E22
Playback ............ 30, 65, 74, E51
Playback action control
...................................................... 77, E71
Playback menu .................. 67, E45
Playback mode ...................................... 30
Playback zoom....................................... 65
Points of interest.... 80, 88, E82
Pop l..................................................... 42
Portrait b ................................................. 35
Power........................................................... 22
Power switch ................................... 1, 22
Power-on lamp.......................................... 1
Preset manual ............................... E33
Pre-shooting cache
............................................ E34, E36
Pressing halfway ................................... 29
Print date.................... 20, 76, E67
Print order............................. 67, E45
Print order date option
................................. 20, E46, E67
Printer...................................... 93, E22
Protect.................................... 67, E49
Q
Quick effects
............ 30, 46, 56, E14, E41
Quick retouch ..................... 67, E15
R
Recording movies ............................... 69
Recording slow motion movies
.................................. 73, E55, E56
Red-eye correction .......... 67, E16
Remove from favorites..... 68, E7
Reset all................................... 77, E78
Rotate image....................... 67, E50
RSCN................................................... E99
S
Scene mode.................................. 35, 36
Selective color I................................ 42
Self-timer .................................................. 50
Self-timer lamp .............................. 1, 50
Sequence display options
................................... 68, E11, E53
Set clock from satellite ... 88, E88
Setup menu ......................... 76, E62
Shooting ............................. 24, 26, 28
Shooting menu.................. 55, E30
Shooting mode .................................... 24
Shutter sound................................ E70
Shutter speed ........................................ 29
Shutter-release button..................... 28
Single ....................................... 56, E34
Single AF ............. 73, E41, E59
Skin softening .......... 57, 63, E42
Slide show............................ 67, E48
Slow sync.................................................. 49
Small picture........................ 67, E19
F 37
F 38
Smart portrait menu....... 55, E42
Smart portrait mode ......................... 44
Smile timer ........................... 57, E43
Snow z..................................................... 35
Soft D....................................................... 42
Sound settings................... 76, E70
Speaker.......................................................... 2
Special effects mode......................... 42
Sports d......................................... 35, 36
SSCN.................................................... E99
Strap for land use .................................... 3
Subject tracking ....... E39, E40
Sunset h.................................................. 35
Super vivid k ........................................ 42
T
Target finding AF.... 56, 61, E39
Thumbnail playback.......................... 66
Time difference ............................ E64
Time zone ............................. 20, E63
Time zone and date
........................................... 18, 76, E63
Toy camera effect 1 m................... 42
Toy camera effect 2 n .................. 42
Tripod socket ........................... 2, F29
TV ................................................ 93, E21
TV settings ............................ 77, E74
U
Underwater C............................ 35, 41
USB cable ................... 92, 95, E23
V
Vibration reduction
....................... 73, 76, E60, E68
View log ................................. 88, E86
ViewNX 2 .................................................. 94
Voice memo......................... 67, E51
Volume.................................... 74, E51
W
Welcome screen ............... 76, E62
White balance..................... 56, E32
Wi-Fi options ....................... 90, E92
Wind noise reduction .... 73, E61
Wireless LAN........................ 89, E92
Z
Zoom........................................................... 27
Zoom control......................................... 27
F 39
No reproduction in any form of this manual, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON
CORPORATION.
2014
FX4C02(11)
6MN39711-02
Scarica
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato. Puoi visualizzare e gestire i tuoi link di chat dopo la registrazione qui.
Link pubblico del documento
Pubblicità