Telehook TH-3270 UFM flat screen wall mount Installation Instructions

( required)
Step 7. Mounting the Display onto the Articulated Arm
Lower the Display so that the Hook
Plate locates with the Mounting
Head.
Hook
Plate
If necessary, adjust the horizontal
angle of the Mounting Rail so that
the Display is level.
Installation Instructions
TM
Fix the Display in position using the
Mount Head Screw and Nylon
Washer supplied (see hardware).
5mm
Allen Key
TIGHTEN
FIRMLY
+/-5°
Adjustment
TH-3270-UFM
Flat Screen Wall Mount | Full Motion
Component Checklist
Mounting Rail
Mounting
Bracket (x2)
Mounting
Head
Nylon
Mount
Washer Head Screw
TIP: Use a Spirit Level to
check the Display is level.
Connect cables to your Display and
route through Cable Clips.
Remove Cable Covers using a Phillips Head Screwdriver, and route
the cables along the length of the arms. Reattach the Cable Covers
to hold the Cables in place.
Cable Clip
Concrete
Anchor (x3)
M10 Coach
Screw (x3)
M5 Washer
(x4)
Articulated Arm
Step 8. Cable Management
Hardware
M6 Washer
(x4)
5mm/6mm
Allen Key
M8 Washer Mount Head
(x4)
Screw
Drilling Guide
TOOLS REQUIRED:
• Power Drill
• Phillips Head Screwdriver
• Flat Blade Screwdriver
• Spirit Level
• 7mm (9/32”) Drill Bit
• 12mm (½”) Masonry Drill Bit
• 16mm (5/8”) Socket Wrench or Shifter
M10 Washer M4/5 Spacer
Bush (x4)
(x3)
M6/8 Spacer
Bush (x4)
Nylon
Washer
Mounting Screws
M8x30mm / M8x50mm (x4 each)
M6x30mm / M6x45mm (x4 each)
M5x30mm / M5x45mm (x4 each)
IMPORTANT INFORMATION
TIP: Leave slack in the
cables to allow full
movement at the joints.
Cables
! IMPORTANT - Install Telehook Wall Mount as per Installation Instructions.
! Telehook Wall Mount has a universal mounting hole pattern that suits a broad range of TVs:
from150 to 805mm wide (6” to 31¾”) and 140mm to 500mm high (5½” to 19¾”).
! Maximum Load: 65kg (143lbs)
! The Manufacturer accepts no responsibility for incorrect installation.
Cable Covers
Step 9. Final Adjustment
Loosen screw with 5mm Allen key
and tilt the Display as desired.
Step 1. Check Components
Tighten screw with 5mm allen key
to lock the Display in desired position.
Tilt Down
TIP: The 5mm and 6mm
Allen Keys can be stored
in the Mounting Rail End
Caps.
LOOSEN
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Locate Drilling Position
Choose the location of your Telehook Wall Mount, ensuring that the wall is structurally sound (for a timber stud
wall, locate the stud using a stud detection device). Use the Drilling Guide to mark out the hole centres.
Top
Drilling Guide
BACK
WALL
Drilling Guide
FRONT
TIGHTEN
End Cap
5mm Allen key
Dust Collector
Tilt Up
Installation Complete
As Display Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 15.05.12 ©
Double-sided
tape (x2)
Un-fold the Drilling Guide and
open the Dust Collector.
Peel away the backing from the
double-sided adhesive tape.
Position the Drilling Guide vertically
onto the wall using a spirit level.
Step 5. Landscape or Portrait Setup
Step 3. Attaching the Articulated Arm to the Wall
Remove the Telehook Arm from
the packaging and open fully.
Wall Plate Cover
NOTE: The Mounting Rail is factory set to mount the Display in a landscape position.
If you wish to mount the Display in a portrait position, please carry out the following instructions (if not, skip to Step 6).
Remove the:
• Cover Plate.
• Two Button Head Screws using the
5mm Allen Key supplied.
ROTATE
Un-clip the Wall Plate
Cover and slide down the arm.
Timber Stud Wall
- Using the Drilling Guide, drill three 7mm (9/32”)
diameter holes, 60mm (23/8”) deep.
- Secure the Mouting Plate to the wall using the Coach
Screw and Washers supplied.
Masonry Wall
- Using the Drilling Guide, drill three 12mm (½”)
diameter holes, 60mm (23/8”) deep.
- Secure the Mouting Plate to the wall using the Coach
Screw, Washers and Anchors supplied.
Cover
Plate
LOOSEN
Masonry
Wall
TIP: Use a small Flat Blade
Screwdriver to help prise the
Cover Plate loose.
Coach Washer
M10 (x3)
Concrete
Anchor (x3)
Coach Screw
M10 (x3)
Coach Washer
M10 (x3)
Washers (x4)
Mounting Screws (x4)
Mounting
Bracket
Top of
Display
Mounting
Hole
Remove the Locking Plate from
each Mounting Bracket using the
5mm Allen Key supplied.
PUSH
TIGHTEN
LOOSEN
TIGHTEN
FIRMLY
6mm Allen Key
Slide the Mounting Rail under
both Mounting Brackets.
Centralise the Mounting Rail on
the Display, then reinstall the
Locking Plates to clamp the
Mounting Rail in position.
Mounting
Bracket
Recessed Mounting Holes or
Display with a Curved Rear Panel
If the Mounting Holes are recessed
into the back of the Display, or the
Display has a curved rear panel, use
the appropriate Spacer Bushes
supplied to pack the Mounting Holes.
NOTE: Ensure the Mounting Bracket
is securely fixed to the Display.
Mounting
Screw
CENTRE
Locking
Plate
Back of Display
Mounting
Bracket
Mounting
Rail
Washer
TIP: Secure the Mounting Bracket to the Display
through the top hole first, then the bottom slot.
Centre
Pin
Step 6. Attaching the Mounting Rail to the Mounting Brackets
Step 4. Attaching the Mounting Brackets to your Display
Choose appropriate Mounting Screws and Washers
from the Hardware supplied to suit your Display.
Hook
Plate
Cable Clip
5mm
Allen Key
Coach Bolt
M10 (x3)
Remove the lower Cable Clip.
Then reinstall the two Button Head
Screws and Cover Plate.
ROTATE 90°
Timber
Stud
OR
Loosen, but do not remove the
Centre Pin using the 6mm Allen Key
supplied.
Rotate the Hook Plate 90°,
then re-tighten the Centre Pin.
Locking
Plate
LOOSEN
Spacer
Bush
Mounting
Hole
PUSH
5mm
Allen Key
Mounting
Bracket
5mm
Allen Key
TIGHTEN
FIRMLY
">