advertisement
MA0905-EC
Operation Guide 668 2168 2505
About This Manual
• Button operations are indicated using the letters shown in the illustration.
General Guide
••••• Press B to change from mode to mode.
••••• Pressing B after performing some operations in any mode returns to the
Timekeeping Mode.
••••• If you do not perform any operation for a few minutes in the Alarm Mode or
Setting Screen, the watch automatically reverts to the Timekeeping Mode.
Timekeeping Mode Alarm Mode
Press B.
Stopwatch Mode Setting Screen
Timekeeping Mode
Minutes
Hour Seconds
In the Timekeeping Mode, press C to switch between the 12-hour and 24-hour formats.
••••• When the 12-hour format is selected, the indicator PM appears on the display to indicate “P.M.” times. There is no indicator for “A.M.” times.
••••• When the 24-hour format is selected, the indicator
24H appears on the display.
••••• A charge indicator appears on the display of this watch when charging is required.
Day
Day of week
Charge indicator
PM indicator
Flashing
To set the time and date
1. Press B three times in the Timekeeping Mode to display the setting screen.
2. Press A to move the selection (flashing) in the following sequence.
Seconds Hour Minutes
Day of week Day Month
3. While the seconds setting is selected (flashing), press C to reset it to 00. If you press C while the seconds setting is in the range of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of 00 to 29, the minutes count is unchanged.
4. While any other setting is selected (flashing), press C to increase the number.
••••• Holding down C changes the setting at high speed.
5. After you set the time and date, press B to return to the Timekeeping Mode.
Alarm Mode
Minutes
Hour
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. When the
Hourly Time Signal is turned on, the watch beeps every hour on the hour.
To set the alarm time
1. Press A while in the Alarm Mode. The hour digits flash because they are selected.
••••• At this time the alarm is automatically turned on.
Mode indicator
Hourly time signal on indicator
Alarm on indicator
2. Press A to change the selection in the following sequence.
Daily Alarm and
Hourly Time Signal on and off
Hour Minutes
3. Press C to increase the selected digits. Holding down C changes the number at high speed.
••••• The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping.
••••• When setting the alarm time using the 12-hour format, take care to set the time correctly as morning or afternoon.
To stop the alarm
••••• Press A to stop the alarm after it starts to sound.
To turn the Daily Alarm and Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and
Hourly Time Signal in the sequence shown below.
Both ON Both OFF Daily Alarm
Only
Hourly Time
Signal Only
••••• The alarm and hourly time signal indicator is displayed in all modes.
To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.
Stopwatch Mode
1/100 second
Seconds
Minutes
The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 59 minutes, 59.99 seconds.
Mode indicator
Elapsed time measurement
Start Stop
Split time measurement
Re-start
Start Split
Split time and 1st-2nd place times
Split release
Start
Stop
Stop
Clear
Clear
Split
First runner finishes.
Display time of first runner.
Stop
Second runner finishes.
Split release
Display time of second runner.
Clear
Power Requirements
This watch works by light energy, so no battery is necessary. Light energy is converted into electric energy by solar cells and stored into the capacitor. Once fully charged, the watch can continue to run for a number of days (Modules 668 and 2168: 4 days, Module 2505: 14 days) without being exposed to light.
■ Charging light
••••• The watch will start to work within about two seconds after it is exposed to light
(such as general office illumination). Set the time and calendar at this time.
••••• You can put on the watch after the “charge indicator ( )” disappears from the display.
••••• The beeper sound may be weak and the display may be dim while the charge indicator is on the display.
••••• Use the information in the table below as a reference how long you need to expose the watch to light when charging it.
1
Operation Guide 668 2168 2505
Charging Time
Conditions
Charging Time
(until charge indicator disappears)
Modules Module
668, 2168 2505
Minimum Daily
Charge
Maximum Charging
Time
Modules Modules Module
668, 2168, 2505 668, 2168 2505
Direct sunlight
(100,000 lux.)
At a sunny window
(20,000 lux.)
Fluorescent light
(5,000 lux.)
General office illumination (700 lux.)
15 min
50 min
4 hrs
—
45 min
3 hrs
12 hrs
—
4 min
12 min
50 min
6 hrs
40 min
2 hrs
—
—
••••• Note the following to ensure that your watch remains charged and running.
* Wear the watch outside your sleeve.
* Place the watch in a well-lit location when you are not wearing it.
2 hrs
6 hrs
—
—
Specifications
Accuracy at normal temperature:
±30 seconds a month
Timekeeping Mode: Hour, minutes, seconds, p.m. (PM), day of the week, day
Time system: Switchable between 12-hour and 24-hour formats
Calendar system: Auto-calendar set at 28 days for February
Alarm Mode: Daily alarm, hourly time signal
Stopwatch Mode: Measuring unit: 1/100 of a second
Measuring capacity: 59 minutes, 59.99 seconds
Measuring modes: Elapsed time, split time and two finishes
Charge Storage: Coin type capacitor
Days to Discharge: Modules 668 and 2168: 4 days
Module 2505: 14 days
(Above values are from full charge to stopping of watch operation, based on 20 seconds of alarm and 24 Hourly
Time Signals per day.)
2
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement