Specifications | Eureka 6900 SERIES Vacuum Cleaner User Manual

Home Cleaning System
Vacuum Cleaner
Household Type
Owner’s Guide
6900 Series
Index
Po
w
Var erhe
ies ad
by Sty
Mo le
del
www.eureka.com
Important Safeguards ........... 2
Service Information ............... 4
Thermal Cut-Off .................... 4
Assembly .............................. 5
Use ..................................... 6-7
Accessories ........................... 8
Cyclonic Bag Saver .............. 9
Dust Bag ............................. 10
Filters ............................. 11-12
Brush Roll ........................... 13
Brush Roll Belt ............... 13-14
Light Bulb ....................... 13-14
Customer Order Form .... 15-16
Warranty .............................. 17
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
•
•
Do not use outdoors or on wet surfaces.
•
•
•
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
•
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do
not run vacuum cleaner over cord. Keep cord away from heated surfaces.
•
•
•
•
•
•
•
•
Hold plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.
•
This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
•
•
•
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
•
•
•
•
•
Use extra care when cleaning on stairs.
Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and
before servicing.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service center before using.
Do not use extension cords or outlets with inadequate current carrying capacity.
Turn off all controls before unplugging.
Always turn off this appliance before connecting or disconnecting either hose or motorized nozzle.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
The hose contains electrical wires. Do not use if damaged, cut or punctured. Avoid picking up sharp objects.
Do not handle plug or vacuum cleaner with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that
may reduce airflow.
Do not use without dust bag in place.
Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive
belt.
Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
Store your cleaner in a cool, dry area.
Keep your work area well lighted.
Unplug electrical appliances before vacuuming them.
SAVE THESE INSTRUCTIONS
2
CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
•
•
•
Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.
•
•
Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les accessoires recommandés par le fabriquant.
•
Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon un guise de poignée. Ne pas fermer une porte sur
le cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le
cordon à distance des surfaces chauffantes.
•
•
•
•
•
Tenir la fiche lorsque vous rebobinez le cordon électrique. Ne pas permettre que la fiche batte l’air.
•
•
•
Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le cordon.
•
Cet aspirateur crée de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin
des cheveux, du linge, des doigts et de toute partie du corps.
•
•
•
Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou cendres chaudes.
•
•
Portez une attention particulière lorsque vous nettoyez les escaliers.
•
•
•
Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.
Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou avant le nettoyage ou l’entretien.
Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire lorsque utilisé par ou prés d’un
enfant.
Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne pas comme il le devrait, s’il a été
échappe, s’il est endommagé, s’il a été laissé à l’extérieur ou échappe dans l’eau, retournez-le à un centre de service
avant d’utiliser.
Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour transporte le courant.
Éteindre toujours l’appareil avant de connecter ou de déconnecter le tuyau ou la lance motorisée.
Fermer tous les contrôles avant de débrancher.
Le tuyau contient des fils électriques et ne doit pas être utilisé s’il est abîmé, coupé ou percé. Éviter de ramasser les objets
aigus.
Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.
Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées; assurez-vous qu’elles soient
dégagées de poussière, mousse, cheveux ou toute autre chose qui pourrait réduire le passage de l’air.
N’utilisez pas sans le sac de poussière en place.
Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour prévenir des brûlures, évitez de
touché la poulie du courroie lorsque vous réparez la courroie.
Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l’essence. Ne pas utiliser dans les
endroits où ces liquides pourraient être présents.
Maintenez un bon éclairage à l’endroit où vous travaillez.
Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
3
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). The plug will
fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus large).
Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The bag may have come dislodged in shipping. Check the bag to insure proper seating before attempting to use the
cleaner. Do not operate the cleaner without a dust bag or the filters. Damage may result to the motor (see Dust Bag and
Filter).
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to avoid
bag breakage, hose clogging, or possible motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. If additional service is required, telephone toll free:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701,
USA. The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited Warranty for
complete service information.
DO NOT OIL the motors (in the canister and the motorized nozzle) or the brush roll at any time. The bearings
are permanently lubricated and sealed.
Rating Plate
The model, type and serial numbers are indicated on the rating
plate located on the underneath side of the cleaner. For prompt
and complete service information, always refer to these numbers
when inquiring about service.
Model No. & Type______________________________
MADE IN
SWEDEN
MODEL
LISTED
C
UL
BLOOMINGTON, IL 61701
SERVICE INFORMATION: 1-800-282-2886
TYPE
HOUSEHOLD TYPE
Serial No._____________________________________
THE EUREKA COMPANY
US
SERIAL NO.
TYPE MENAGER
120 V AMPS
60 HZ 12.0
945G
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push the switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such
as a full bag, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before
attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner stil l
does not run, then take it to a Eureka Authorized Service Center for repair.
4
ASSEMBLY ITEMS
NOTE: Unpack and identify all parts. Fully assemble before using.
14
13
1
3
2
10b
6
4
5
10c
11
7
12
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
7c
8
©
7b
16
©
7a
10a
Po
Power Switch
we
V
ari rhea
Cordaway Cord Reel
es
d
by Sty
Bag Change Indicator
Mo le
del
Bag Cover Latch
HEPA Filter
Tool-Pak Cover Latch
Tool-Pak Storage
a) Dusting Brush
b) Crevice Tool
c) Upholstery Nozzle
Floor Brush
Disposable Dust Bags
Hose has Power-Touch Handle with remote controls (10a) and coupling (10b) with plug (10c).
See instructions on pages 6 and 7.
Hose Plug Connection
Canister Handle
Button-Lock Extension Wand with plug retainer
Button-Lock Extension Wand with cord retainer
Motorized Nozzle
Quick Release™ Wand System
15
Always carry the vacuum by the handle when cleaning steps, etc.
5
How to Assemble and Use
10
k
rpe
n
Ba
*Power ON/OFF can be controlled on some models
from the POWER-TOUCH handle switch or canister
ON/OFF switch. Other models can only use the
canister switch.
Remote Speed Control (optional)
Adjusts the speed of the canister motor, slide to reduce
or increase power as needed.
Select bare floor or
carpet cleaning
Ca
Remote ON/OFF Selector for bare floor or carpet
Carpet – push down on front
*Off – middle
Bare Floor – push down on back
t
Off
re
Flo
or
POWER-TOUCH® Handle
Power-Touch
Hose Handle
k
n
4
3
Vacuum Control
Cleaning suction is reduced by
pushing lever to LOW position.
Place lever at HIGH position
to increase suction for carpet
cleaning.
Available on models without
Remote Speed Control.
Detail A
1. Snap interlocking wands together.
n
2. Push assembled wands into the quick release
socket attached to a power nozzle.
1
3. Push motorized nozzle plug into the retainer
located at the top of the upper wand; secure cord
in slot (Detail A).
4. Place Power-Touch hose handle into wands until
plug connects and button locks.
Continue on next page to complete assembly.
n
2
Step here
&
pull up
to release
n
Quick
Release
Lower
Assembly
k
k
6
Handle Release
8
Continued
8. Step on motorized nozzle to release handle; pull back
to comfortable work position.
5. Insert hose coupling into top of canister.
6. Push hose power cord into receptacle located near
the canister handle.
9. Push On/Off canister switch. Symbol - is the
international symbol for on/off.
(A thermostat automatically shuts off the motor if it
overheats, see Thermal Cut Off.)
7. Pull cord out, and push plug into outlet. To rewind,
step on Cordaway cord reel button, hold and guide
plug while it rewinds.
10. Bare floor or carpet cleaning selection on remote
control, only.
NOTE: Optional remote controls on the hose
handle operate only if the canister switch
is on.
9
5
s
6
7
7
11
a
b
c
b
a
d
c
8
Your new vacuum cleaner may be equipped with an optional Cyclonic Bag Saver.
To assemble the cleaner with this option follow these instructions,
otherwise follow the owner’s guide for assembly.
This accessory reduces the need for frequent bag changes. It does
not eliminate the use of a paper bag. To remove the Cyclonic Bag
Saver, follow the steps in reverse and reattach the large upper wand.
Fig. 1
1
UNPACKING AND ASSEMBLING
3
2
Fig. 1a
Unpack and check that all the parts are included. The Cyclonic Bag
Saver consists of three main parts, see Fig. 1:
1. Cyclonic Housing
2. Cyclone Dust Cup
3. Retaining Clip
Attach retaining clip onto the rear of the cyclonic cup as shown in
Fig. 1a.
Attaching the Cyclonic Bag Saver onto the vacuum
cleaner
Fig. 2b
Fig. 2a
Tab &
Slot
Handle
Fig. 3
Detail A
Nozzle
MAX
NOTE: If the two long wands have already been assembled to the
powerhead, remove the long upper wand to assemble the
Cyclonic Bag Saver.
Your vacuum cleaner is equipped with three wands. Locate the short
wand.
Fig. 2a Line up the small hole at the top of the short wand with the
arrow on the front of the cyclonic housing. Push the short
wand into the top of the cyclonic housing until it clicks into
place. (You may need to rotate the wand slightly.)
Fig. 2b Attach the cyclonic dust cup onto the cyclonic housing. Place
the slot in the cyclonic dust cup over the tab on the cyclonic
housing. Then grasp the handle on the cyclonic dust cup,
and pivot the cyclonic dust cup up and over the ledge on the
cyclonic housing.
Fig. 3 Push the nozzle at the bottom of the cyclone unit into the
top of the long lower wand. Adjust the position of the cyclone
unit. Push the long lower wand into the powerhead unit. Plug
the powercord into the powercord retainer at the top of the
cyclonic housing, see Detail A. Attach the powertouch handle
following instructions in the owner’s guide.
MAX
Important Safety Information
Long Lower Wand
Powercord
-
Do not vacuum surfaces which have been subjected to
inflammable solvents.
Do not pick up any liquid.
Do not pick up hot ashes which could cause a fire.
Emptying
Empty the dust compartment of the cassette after each use or when
the dust cup is filled up to the MAX level, Fig. 3. Detach the dust cup
by following the instructions in Fig. 2b in reverse.
Empty the contents into a waste container. To reattach the dust cup
again follow the described steps in Fig. 2b.
Maintenance
Powerhead Unit
The Cyclonic Bag Saver can be washed in cold or warm water and a
mild detergent. Thoroughly dry the dust compartment with a soft towel
before using it again. If the cyclone unit clogs, use the vacuum cleaner
to unclog it.
9
HOW TO MAINTAIN
The paper bag and filters play a very important role in the efficiency of the vacuum cleaner. The purpose of the paper bag is
to trap dirt and at the same time the paper must be porous enough to allow air to pass through. If the paper bag or filters
become clogged, no air can pass through the cleaner and no cleaning takes place regardless of how powerful the unit. To
keep the cleaner operating at maximum efficiency, change the dust bag frequently and clean the filters as necessary.
Some fine particles can restrict airflow very quickly and will decrease performance even before the bag appears to be full.
When vacuuming carpet fresheners or cleaners, plaster dust, or similar fine substances, clean the bag and filters more often.
Bag Change Indicator
The bag change indicator bar fills as the airflow through the bag decreases.
Certain types of fine particles like powder, plaster dust, or carpet fibers can
restrict airflow very quickly and will decrease performance even before the
bag appears to be full. When the warning appears, change the disposable
dust bag to restore maximum performance. If a clean dust bag does not
restore maximum performance, clean the filters and check the hose and
wands for obstructions.
Empty Bar
HOW TO CHANGE DISPOSABLE DUST BAG
NOTE: Turn off the power switch and disconnect
electrical cord from wall socket before
changing dust bag. Never use the cleaner
without a dust bag or filters.
1
To remove used dust bag:
1. Unlatch the hose latch to open the lid of bag
compartment.
2. Push the bag’s cardboard disc closed, grasp
the cardboard collar and lift out the full bag.
3
2
©
To install new dust bag:
3. Put in the new dust bag (part number 60284)
by slotting the cardboard collar into the
channel holder. The lid cannot be closed over
a bag that is not fitted into place.
10
Filled Bar
Filters
For maximum efficiency, be sure to maintain the motor filter and the final filter regularly.
Motor Filter
Inspect the motor filter with each disposable dust bag
change.
The motor filter in the bag compartment should be cleaned
when necessary or about twice a year.
•
Open the cover and lift up on the filter.
•
Shake out thoroughly.
•
Replace with a new filter if necessary, part number
60541.
11
Filters (continued)
1
2
HEPA Filter
Check the HEPA filter with each disposable dust bag
change. Replace after every six bag changes or when
obviously dirty.
1. To change HEPA filter, press exhaust grille to open the
filter cover.
2. Remove filter cover by lifting up.
3. Pull out the used HEPA filter by using finger tab.
4. Put in new HEPA filter. (Part number 60286)
5. Replace filter cover.
12
3
Brush Roll
The brush roll turns to sweep and comb the carpet nap. Keep the brush roll free from hair and threads so it will continue
cleaning. When the bristles of the brush roll no longer touch a piece of cardboard held across the bottom plate, the brush roll
is ineffective because the bristles no longer touch the carpet nap. To maintain the most effective cleaning, install a new brush
roll.
Brush Roll Belt and Light Bulb
The brush roll belt on the motorized nozzle drives the brush roll to agitate, sweep, and comb the carpet nap. The belt should
be checked regularly to be sure that it is in good condition. Replace the belt if it is stretching, cracking, or slipping. Cut away
any hair or thread wound around the brush roll or belt pulley because the buildup could cause the belt to rotate unevenly.
How to Replace Worn Belt or Light Bulb (On Some Models)
Continue to step 2 to change belt. Skip to step 7 to
replace hood.
{
Replace light bulb, if necessary. Use GENUINE
EUREKA replacement bulb (refer to customer order
form).
{
1. Remove four screws from bottom side. Turn unit over;
pull up on hood to remove.
{
Turn off the switch and unplug the electrical cord before replacing belt or bulb. Pulleys can become hot
during normal use. To prevent injury, avoid touching the pulleys when servicing the drive belt.
{
Note:
Motor Pulley
2. Lift out brush roll and discard used belt.
{
3. Put new belt around brush roll pulley first; then the
motor pulley.
4. Place left end cap into the base.
5. Pull right end of brush roll to stretch belt. Secure right
end cap into base.
6. Rotate brush roll to seat belt.
Look for the
symbol.
{
7. Position hood; secure with screws.
Brush Roll Pulley
Use GENUINE EUREKA replacement belt, 58065.
13
How to Replace Worn Belt or Light Bulb (On Some Models)
Note: Disconnect power cord and wands from electrical hose before replacing belt or bulb. Belt pulleys can become
hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.
4. Return brush roll into base.
1. Remove two screws from bottom side. Turn over to
grasp hood near handle socket and lift forward.
Replace headlight bulb, if necessary. Use GENUINE
EUREKA replacement bulb (refer to customer order
form).
Continue to step 2 to change belt. Skip to step 7
and 8 to replace hood on motorized nozzle.
Brush
Roll
Pulley
{
5. Rotate belt onto motor pulley.
6. Replace brush roll cover.
2. Remove two screws located in front of the light bulb
and lift up to remove the brush roll cover.
Motor Pulley
Ridge
{
7. Tilt cover over ridge and push down.
8. Secure with screws on underside (refer to 1).
3. Lift out brush roll; replace new belt around brush roll
pulley.
Look for the
symbol.
Use GENUINE EUREKA replacement belt, 58065.
14
2/01
The Eureka Company
P.O. Box 2799
Bloomington, IL 61702-2799
ORDER FORM
(Not applicable in Canada)
Name
S
O
L
D
Name
Address (street address needed for UPS)
City
T
O
Telephone
State
(Day)
(Eve)
Zip
(Fax)
S
H
I
P
Address (street address needed for UPS)
T
O
Telephone
City
IMPORTANT:
Be sure to include
your model, type,
and serial numbers.
These numbers
may be found on
the rating plate.
Model Number:
(Day)
State
Zip
(Eve)
(Fax)
Part No.
Qty. Price (USD)
Genuine Eureka Bags, Belts and Filters
Disposable Bags (style EX), package of 3
60284
4.99
Belts, package of 2
58065
2.49
Motor Filter
60541
3.49
60286A
19.99
Dusting Brush with swivel bristles
54903
16.19
Upholstery Nozzle
54904
10.19
Crevice Tool
54905
4.59
Expandable Crevice Tool
60112
22.69
54785A
10.39
Tool Rack, 18 inch wall storage for most tools
52001
26.89
Micro Tool Set for Keyboards, etc.
54002
12.99
Type:
HEPA Filter (Style HF1)
Serial Number:
To Order
By Phone
1-800438-7352*
#
HOURS:
Call between 8 a.m.
and 4:45 p.m.,
central standard time
Monday through Friday.
By FAX
1-309823-5789
To Answer Problems
or Questions for U.S.A.
and Canada call:
Accessories/Tools
Floor Brush
1-800282-2886*
7 a.m. to 8 p.m.
central standard time
Monday through Saturday.
*En Mexico llame al
5670-6169
By Mail
Simply fill out
this Order Form.
Please be sure to
include day
and evening
phone numbers.
www.eureka.com
Wands (chrome button lock unless otherwise noted)
Wand, Upper for Power-Touch Handle only
37738-5
11.69
Wand, Lower, 19 inch, black cord channel
36879-5
9.89
37737
9.39
Wand, 19 inch
SUBTOTAL
Total
Part No.
Qty.
Price (USD)
Total
Hose (swivel coupling)
Electric, 3-pos Power-Touch Handle Model 6993
60783-1
76.19
Electric, 2-pos Power-Touch Handle Model 6978
60782-1
61.29
60858-1
14.19
59045
2.39
37072-3
13.19
Brush Roll
Brush Roll with 2 rows of bristles
Miscellaneous Items
Light Bulb (15 watt)
Extension Cord, 10 foot, white only
Subtotal From Front
Total (prices subject to change without notice)
Tax (add state tax & local taxes as required by law)
Postage & Handling Charge (within U.S.A.)
$5.50
TOTAL
TOTAL ENCLOSED
Method of payment (No C.O.D. Orders)
Check or money order (payable to The Eureka Company). Do not send currency.
Charge to my
Visa (13/15 digits)
Acct. number
MasterCard (13 digits)
Amer. Express (15 digits)
Expiration Date
Signature (full name as shown on acct.)
59411
© 2001 White Consolidated Industries, Inc.
Printed in U.S.A.
THE EUREKA LIMITED WARRANTY
What This Warranty Covers
Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of one year. The warranty is granted only to the
original purchaser and members of his or her immediate household. The warranty is subject to the following provisions.
What This Warranty Does Not Cover
• Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brush roll bristles
• Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Guide.
• Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
What The Eureka Company Will Do
The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this warranty. As a matter of warranty policy, the Eureka Company
will not refund the consumer’s purchase price.
Warranty Registration
Please fill out and return the warranty registration card accompanying your cleaner.
Obtaining Warranty Service
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station.
You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service and Repair.” Be certain that the Warranty Station is “Eureka Authorized.”
For the location of the nearest Eureka Authorized Warranty Station or for service information, telephone toll free:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company, 866
Langs Drive, Cambridge, Ontario N3H 2N7.
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping charges to the Eureka Authorized Warranty Station.
Return shipping charges will be paid by the Warranty Station. When returning parts for repair, please include the model, type, and serial number from the data plate on the cleaner.
Further Limitations and Exclusions
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of Merchantability or any warranty for Fitness For A Particular
Purpose is limited to the duration of this warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above. In no event shall Eureka be liable for any consequential or incidental damages you
may incur in connection with your purchase or use of the cleaner. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary by state.
GENUINE
EUREKA PRODUCT
Questions & Answers about Genuine Eureka Products
Q: Why should I use only Genuine Eureka paper bags, belts, and parts in my Eureka vacuum cleaner?
A: Using Genuine Eureka Products, which are made to our exacting specifications and engineered with emphasis on quality, performance, and customer satisfaction,
ensures the long life and cleaning efficiency of your vacuum cleaner. Overall, this saves you money and helps to keep your home clean.
Q: How can I be sure I am using only genuine Eureka products in my vacuum cleaner?
A: Typically, packaged products and paper bags can be identified by a “Genuine Eureka Product” symbol (see illustration above). For further identification assistance,
you may call our toll-free number, 1-800-282-2886, for the location of a nearby Eureka Authorized Warranty Station.
Q: Are there any differences between “made to fit” or “imitation” and Genuine Eureka paper bags, belts, and parts?
A: Yes, there are some very important differences in materials, quality, and reliability. Many customers have mistakenly purchased “imitation” paper bags and parts
while thinking they purchased genuine. Unfortunately, many of these customers discovered the differences after they experienced related difficulties.
For Genuine Eureka Value, Accept No Imitations!
THE EUREKA COMPANY
Bloomington, Illinois 61701
Household Warranty
abs 190
17
Part No. 70830 (1/01)
©2000 White Consolidated Industries, Inc.
Printed in U.S.A.
Download PDF

advertising