Configuring
Web-based Manager
Use the following procedure to connect to the web-based manager for the first time.
Configuration changes made with the web-based manager are effective immediately without resetting the FortiBridge unit or interrupting service.
To connect to the web-based manager
1. Connect the management port of the FortiBridge unit to Ethernet port of the management computer.
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through
Ethernet cables to connect the devices through a hub or switch.
2. Configure the management computer to be on the same subnet as the FortiBridge management port interface.
To do this, change the IP address of the management computer to 192.168.1.2 and the netmask to 255.255.255.0.
3. To access the FortiBridge web-based manager, in your browser, go to http://192.168.1.99.
4. Type admin in the Name field and click Login.
To configure Probes
Probes monitor the FortiGate unit by sending packets from the INT 2 interface through the FortiGate unit to the EXT 2 interface. If probe packets are not received at the EXT 2 interface the FortiBridge unit detects a failure.
Configure probe settings to set actions on failure, add a dynamic IP pattern used by the probe packets, and enter the serial number of the FortiGate unit. Actions on failure can include failing open and sending an alert email, a syslog message, and an SNMP trap.
1. Go to Probe > Settings.
2. Enter the Probe IP address pattern (#.#.#.*).
3. Enable ping, HTTP, FTP, POP3, SMTP, and/or IMAP probes.
4. Set the Port Number for each protocol.
5. Change the Failure Threshold and probe Interval for each probe.
To set up Notifications
1. Go to Probe > Notifications.
2. Enter a Notification Message Tag.
3. Optionally, select the Syslog check box and enter the IP address, port and facility of the Syslog server that receives FortiBridge syslog messages.
4. Optionally, select the Email check box and enter the SMTP server, email addresses,
SMTP user name, and password of the users to send the alert email.
5. Optionally, select the SNMP check box and enter the name, hosts, and traps of the
SNMP manager to send alerts to a community.
To configure the Management, Default Gateway, and Primary and Secondary DNS server
IP addresses
1. Go to System > Status > Management Port area and click Change.
Command Line Interface
To connect to the FortiBridge unit
1. Use a RJ-45 to DB-9 cable to connect the FortiBridge management port to the management computer serial port.
2. Start a terminal emulation program (such as HyperTerminal) on the management computer. Use these settings: Baud Rate 9600, Data bits 8, Parity None, Stop bits 1,
Flow Control None.
3. At the login: prompt, type admin and press Enter twice.
(The login prompt is preceded by the server default host name.)
To configure the FortiBridge unit using the CLI
1. Change the management IP address. config system manageip
set ip <intf_ip>/<netmask_ip> end
2. Configure the primary and secondary DNS server IP addresses.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip> end
3. Configure the default gateway.
config system route
edit 1
set gateway <gateway_ip> end
4. Change the administrator password.
config system admin edit admin set password <password> end
Shutting down the FortiBridge unit
When powering off the FortiBridge unit, always shut down the unit using the following procedures before disconnecting the power supply. Not following this procedure can increase the risk of damaging the FortiBridge flash disk.
To power off the FortiBridge unit
1. Go to System > Status.
2. In the Unit Operation area, click Shut Down.
3. Once the indicates the shut down procedure has completed, disconnect the
FortiBridge unit from the power source.
Visit these links for more information and documentation for your Fortinet product:
Technical Documentation - http://docs.fortinet.com Fortinet Knowledge Center - http://kb.fortinet.com
Technical Support - http://support.fortinet.com Training Services - http://campus.training.fortinet.com
QuickStart Guide
FortiBridge-2002F
FortiBridge 2002F
USB1
CONSOLE1
MODEM1 MGMT1
INT1
INT2
INT1 EXT1
INT2
FortiGate
EXT2
EXT1
EXT2
HA1 BYPASS1
MODE1 RESET1
PWR1 NORMAL1
USB2
CONSOLE2
MODEM2 MGMT2
INT3
INT4
INT3 EXT3
INT4
FortiGate
EXT4
EXT3
EXT4
HA2 BYPASS2
MODE2
PWR2 NORMAL2
RESET2
AC Power
Chassis
Dimensions
Network Interfaces
50 W, 100 - 240 VAC, 50 - 60Hz
1U
44.0 cm x 30.1 cm x 4.44 cm
4 1GB LC SFP (SX) Ingress/Egress ports
4 1GB SFP (SX) Ingress/Egress ports
2 10/100/1000 Management ports
2 USB connections
2 Console ports
2 Modem connections
© Copyright 2010 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks of their respective holders.
Regulatory Compliance
FCC Class A Part 15, UL/CB/CUL, C Tick, VCCI
11 May 2010 01-410-124834-20100511
Package Contents
FortiBridge 2002F
USB1
CONSOLE1
MODEM1 MGMT1
INT1 and
INT2
INT1
INT2
INT1 EXT1
INT2
FortiGate
EXT2
EXT1 and
EXT2 Reset1
Mode1
EXT1
EXT2
HA1 BYPASS1
MODE1 RESET1
PWR1 NORMAL1
USB2
CONSOLE2
MODEM2 MGMT2
INT3 and
INT4
INT3
INT4
INT3 EXT3
INT4
FortiGate
EXT4
EXT3 and
EXT4 Reset2
Mode2
EXT3
EXT4
HA2 BYPASS2
MODE2 RESET2
PWR2 NORMAL2
USB1
Modem1
Console1 Management1
LEDs LEDs USB2
Modem2
Console2
Management2
LEDs LEDs
DISCONNECT TWO POWER SUPPLY CORDS
BEFORE SERVICING
DISCONNECT TWO POWER SUPPLY CORDS
BEFORE SERVICING
Ground
Power button
AC power connection
Power button
AC power connection
SFP SX x4 Power cable x2
Straight-through
Ethernet cable
Factory Defaults
Tools and Documenation
QuickStart Guide
FortiGate-30B
FortiBridge 2002F
USB1
CONSOLE1 MODEM1 MGMT1
INT1
INT2
INT1
INT2 FortiGate
EXT1
EXT2
EXT1
EXT2
HA1 BYPASS1
MODE1
PWR1 NORMAL1
RESET1 USB2
CONSOLE2 MODEM2 MGMT2
INT3
INT4
INT3 EXT3
INT4 FortiGate EXT4
EXT3
EXT4
HA2 BYPASS2
MODE2
PWR2 NORMAL2
RESET2
Copyright 2010 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
REGISTER
Administrator user name
Administrator password
NAT/Route mode
Management1
Management2 admin
(none)
192.168.1.99
0.0.0.0
To reset the unit to the factory defaults, in the CLI type the command:
execute factory reset
LED Description
LED
Power
Normal
HA
Bypass
INT and
EXT LEDs
MGMT1 and
MGMT2
Ports
State
Green
Off
Description
The unit is powered on.
The unit is powered off.
Green
Green
Off
Green
The unit is being used in Normal mode.
The unit is being used in a HA cluster.
The unit is in stand-alone mode.
Bypass network activity at this interface.
Normal status.
Off
Green
Green flashing
The correct cable is in use and the connected equipment has power.
Network data is being sent or received.
Off No link established or the interface has been turned off.
Link/Activity (left) Green Port has power and network connection.
Link/Activity (left) Green flashing
Speed (right) indicator is
Green
Speed (right) indicator is
Amber
Speed (right) indicator is Off
Network data is being sent or received.
Connected at 1000 Mbps.
The interface is connected at 100
Mbps.
The interface is connected at 10
Mbps.
Interface Description
Interface Type Speed
Console1 and Console2
RJ-45 9600 bps
8/N/1
Protocol
RS-232 serial
Modem1 and Modem2
USB1 and
USB2
MGMT1 and
MGMT2
INT1, INT3,
EXT1, and
EXT3
INT2,
INT4,
EXT2, and
EXT4
RJ-11
USB
RJ-45 10/100/1000
Base-T
LC
SFP
SFP
Description
Connection to the management computer. Provides access to the command line interface (CLI).
Phone line for internal modem.
USB Two optional connections to a USB key for installation.
Ethernet Two management ports.
1000Base-SX Ethernet Fiber optic connections to gigabit optical networks.
1GB-SX Ethernet Small form-factor pluggable transceiver.
Connecting
Connect the FortiBridge unit to the internal and external networks and the Forti-
Gate unit. Normally, you would use straight-through ethernet cables to connect the FortiBridge unit. However, for some connections you may need a crossover ethernet cable (for example, for compatibility with network devices that do not support Auto MDI/MDIX).
• Connect the FortiBridge INT 2 interface to the FortiGate unit internal interface.
• Connect the FortiBridge EXT 2 interface to the FortiGate unit external interface.
• Connect the FortiBridge INT 1 interface to the internal network.
• Connect the FortiBridge EXT 1 interface to the external network.
• Turn on the FortiGate unit and any network equipment that was turned off.
• Connect the power cords at the back of the FortiBridge unit. Plug the other end of the power cables into a grounded electrical outlet.
• The PWR and Bypass Mode LEDs turn on. After a short time, the Forti-
Bridge unit switches to Normal mode. The Bypass LED turns off and the
Normal LED turns on.
