Freestyle 814 Watch Operating instructions

Ba .
Freestyle
#814 GENERATOR
WATCH INSTRUCTIONS
FEATURES
* CURRENT TIME (HR., MIN..& SEC.)
* DAY/MONTH/DATE
- CHRONOGRAPH WITH SPLIT
OR LAP TIMES
DUAL ALARMS ( 1 DAILY
REPEATING, 1 NON-
REPEATING REMINDER.)
+ COUNTDOWN STOP
COUNTDOWN REPEAT,
COUNTDOWN CHRONO
LAF & COUNTDOWN CHRONO
SPLIT TIMERS
* DUAL TIME
* HOURLY CHIME
* OPTIONAL 24-HR. TIME
(MILITARY TIME. )
= WATER RESISTANT TO
300 FT. OR 100M
« NIGHT VISION™ ELECTRO-
LUMINESCENT BACKLIGHTING
NORMAL TIME MODE
{ The term "Mode" means the function
status of the watch.) Normal time mode
shows hours, minutes, seconds, day and
date. To set time, see operating
instructions on How to Set Normal Time.
KEY TO SYMBOLS
LT - Left Top (Light/Set)
LB - Left Bottom (Mode)
RT - Right Top (Start/Stop)
RB - Right Bottom (Reset)
HOW TO SET NORMAL TIME, DATE
AND 24-HOUR FORMAT
Note: If no buttons are pressed for
approximately ten seconds, the watch will
exit the setting mode.
From Normal Time mode, press and hold
the Light/Set button LT for approximately
uns seconds; the seconds digits will
lash.
Pressing the Start/Stop button RT will
reset the seconds digits to 0. If seconds
are greater than 30, one will be added to
the minutes digit.
if |
| L
To set minutes, press Mode button LB,
single minutes digit will flash. To advance
flashing minutes digit, press Start/Stop
button RT, hold for rapid advance.
To set tens of minutes, press Mode button
LB; tens of minutes will flash. To advance
flaching le ns of minutes press Start/Stop
button RT; hold for rapid advance.
Continuing through the setting mode, the
setting sequence is a continuous loop of:
seconds * single minutes + tens of minutes
* hours + day/month/date » 12/24-hour
mode, and looping back to seconds.
When setting is complete, press Light/Set
button LT to return to normal time mode.
HOW TO OPERATE
CHRONOGRAPH/STOPWATCH
The chronograph will record a
maximum of 99 hours, 59 minutes and
59.99 seconds. Press Mode
button LB once from normal time mode
to enter the chronograph mode. Normal
time will remain on the lower row,
chronograph on the upper row. The “C"
flag will be displayed
и
Reset the chronograph to zero by
pressing Reset button RB. Press the
Light/Set button LT to switch between
Lap and Split mode.
("LP” flag will be displayed for lap mode
and “+” flag will be displayed for split
time mode.
| L/
Split time is the time elapsed since the
start of the chronograph. To use the split
time feature, "w" flag must be displayed.
Press Start/Stop button RT to start
chronograph. "++" flag will begin flashing.
Press Reset button RB to view split time.
Chronograph will continue to count while
split time is displayed. To release split
time and return to running chronograph,
press Reset button RB.
Each press of Reset button RB will
button RT. Reset the chronograph to
zero by pressing the Reset button RB.
Lap time is the time elapsed since the
previous lap. To use the lap time feature,
“LP” flag must be displayed. Reset the
chronograph to zero by pressing the
Reset button AB. Enter Lap mode by
pressing Light/Set button LT. Press
Start/Stop button RT to start chronograph.
"LP" flag will begin flashing. Press Reset
button RB to view lap time. The
chronograph will start counting next lap
while lap time is displayed. To release
lap time and return to running chrono,
press Reset button RB. Each press of
Reset button RB will display a lap time.
| %
+,
LA | #
To stop chronograph, press Start/Stop
button RT. Reset the chronograph to
zero by pressing the Reset button RB.
HOW TO SET AND OPERATE THE
ALARMS AND HOURLY CHIME
From normal time mode, press Mode
button LB twice to enter the alarm mode.
Normal time remains on the lower row,
alarm time on the Upper row, Pressing
Reset button AB will toggle between
alarm |, indicated by the RIGHT "+" flag,
and alarm 2, indicated by the LEFT “4”
flag. Alarm 1 is a daily, repeating alarm,
and alarm 2 is a one time only reminder
alarm. Va A
or: 5
Йон —— Y
Press and hold Light/Set button LT for
approximately three seconds to enter
alarm setting mode. The minutes digit
will flash. Press Start/Stop button RT to
advance the flashing minutes digit.
Press Mode button LB to advance tens
ot minutes. Press Start/Stop button RT
to advance the flashing tens of minutes
digit.
Press Mode button LB to advance the
hours digit. Press Start/Stop button RT
to advance the flashing hours digit. While
setting the flashing hours digit, "A" or “P"
is displayed on the right side. "A"
designates a.m. and "P" designates p.m.
LT
>
[
f
(
Press Light/Set button LT to exit the alarm
setting mode. To activate the alarm while
in alarm mode: Press Start/Stop button
RT to arm or disarm the alarm “4” and/or
hourly chime “ a ®. Note the setting
sequence is. alarm on, chime on, both
alarms and chime on, both alarms and
chime off.
Again, press Reset button RB to toggle
between alarm 1 and alarm 2. Alarm 2
Is set and activated the same way as
alarm 1.
| * = alarm 1 on.
| wil] |
fa | =
P ull] |
HOW TO OPERATE THE
COUNTDOWN TIMER
alarm 2 on
Press Mode button LB three times from
the normal time mode to enter the
countdown timer mode. Normal time will
remain in the lower row and the timer will
appear on the upper row. " © ” flag will
be displayed. (Minimum time setting is
one minute; maximum time setting is 99
hours, 59 minutes).
*Note: there are four timer functions in
this mode. To select between these
features, press Reset button RB until the
desired function (noted by its respective
flag) is displayed
TIMER COUNTDOWN - “e” flag will be
displayed. This function will countdown
from a preset time. When the countdown
time is reached, the timer will beep and
will automatically reset to the preset time.
N PD ed
TIMER COUNTDOWN REPEAT-
Press Reset button AB; "Y" and “DD "
flags will be displayed. This function will
countdown from a preset time. When the
countdown time is reached, the timer will
beep,automatically reset, and begin
counting down repeatedly until the
Start/Stop button RT is pressed.
TIMER COUNTDOWN CHRONO LAP-
Press Reset button RB, “C", “LP” and
“7” flags will be displayed. This function
will countdown from a preset time. When
the countdown time is reached, the timer
will beep and automatically start a
chronograph. This chronograph has a
chrono lap timer, identical to that in the
chronograph/stopwatch “LP” mode.
7 |
TIMER COUNTDOWN CHRONO SPLIT-
Press Lap/Reset button AB; "C”, 49"
and “e» * flags will be displayed. This
function will countdown from a preset
time. When the countdown time 15
reached, the timer will beep and
automatically start a chronograph. This
chronograph has a chrono split timer,
identical to that in the
chronograph/stopwatch * 4 * mode.
To set the countdown time, press and
hold the Light/Set button LT for
approximately three seconds. The
minutes digit will flash. To advance the
flashing minutes digit, press Start/Stop
button RT. _ я
X