Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians.

*8196213*

24-Hour Service Hotline 1-800-551-8633

Price: $6.00

819-6213

NOV 08

THIS PAGE INTENTIONALLY LEFT BLANK

NOTICE

IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS

EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY

FROM FRYMASTER/DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE

PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL

BE VOID. FURTHER, FRYMASTER/DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY

CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY

OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART

AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER.

THE HCP IS NOT SUITABLE FOR OUTDOOR USE. WHEN OPERATING THIS UNIT, IT MUST

BE PLACED ON A HORIZONTAL SURFACE.

THE HCP IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET CAN

BE USED. THIS APPLIANCE MUST NOT BE CLEANED WITH A WATER JET.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN

THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

DO NOT OPERATE OR SERVICE THE HCP WITHOUT FIRST READING THIS MANUAL.

DO NOT OPERATE THE HCP UNLESS IT HAS BEEN PROPERLY INSTALLED AND

CHECKED.

DO NOT OPERATE THE HCP UNLESS ALL SERVICE AND ACCESS PANELS ARE IN PLACE

AND PROPERLY SECURED.

DO NOT ATTEMPT TO REPAIR OR REPLACE ANY COMPONENT OF THE HCP UNLESS ALL

POWER TO THE UNIT HAS BEEN DISCONNECTED.

USE CAUTION WHEN SETTING UP, OPERATING, OR CLEANING THE HCP TO AVOID

CONTACT WITH HEATED SURFACES.

Table of Contents

Installation, Warranty, Parts

1-1

Software 2-1

Power Up

3-1

Operational Overview 4-1

Entering Passwords Adding Menu Items

Programming

Changing from 4 to 2-Slot Operation

5-1

6-1

6-2

Saving Cabinets

7-1

Loading 7-2

Temperature Display 8-1

Uploading Cabinet Configurations and Daily Activity to Palm 9-1

Loading Software for the Palm

Checking Palm Operating System Version Number

10-1

10-1

HCP

1 HCP

The Frymaster HCP is a short-term holding device to extend the freshness of a wide variety of cooked products.

1.1 Warranty Statement

A. Frymaster L.L.C. makes the following limited warranties to the original purchaser only for this equipment and replacement parts:

1.1.1 Warranty Provisions – Universal Holding Cabinet

A. Frymaster L.L.C. warrants all components against defects in material and workmanship for a period of one year.

B. All parts, with the exception of fuses, are warranted for one year after installation date of cabinet

C. If any parts, except fuses, become defective during the first year after installation date,

Frymaster will also pay straight-time labor costs to replace the part, plus up to 100 miles/160 km of travel (50 miles/80 km each way).

1.1.2 Parts Return

A. All defective in-warranty parts must be returned to a Frymaster Authorized Factory Service

Center within 60 days for credit. After 60 days, no credit will be allowed.

1.2.3 Warranty Exclusions

• This warranty does not cover equipment which has been damaged due to misuse, abuse, alteration, or accident such as:

• Improper or unauthorized repair;

• Failure to follow proper installation instructions and/or scheduled maintenance procedures;

• Improper maintenance;

• Damage in shipment;

• Abnormal use;

• Removal, alteration, or obliteration of the rating plate;

This warranty also does not cover:

• Transportation or travel over 100 miles/160 km (50 miles/80 km each way), or travel time over two hours;

• Overtime or holiday charges;

• Consequential damages (the cost of repairing or replacing other property that is damaged), loss of time, profits, use or any other incidental damages of any kind.

1-1

HCP

There are no implied warranties or merchantability or fitness for any particular use of purpose.

For international warranty, the above procedures apply, except that the customer is responsible for freight and duty charges.

PARTS ORDERING AND SERVICE INFORMATION

Parts orders may be placed directly with your local Frymaster Factory Authorized Service Center

(FASC)/Distributor. A list of Frymaster FASC/Distributors was included with the cabinet when shipped from the factory. If you do not have access to this list, please contact the Frymaster Service

Department at 1-800-551-8633 or 1-318-865-1711.

To speed up your order, the following information is required:

Model Number_____________________________________

Serial Number_____________________________________

Voltage___________________________________________

Item Part Number___________________________________

Quantity Needed____________________________________

Service may be obtained by contacting your local Frymaster Authorized Service Center/Distributor.

Service information may be obtained by calling the Frymaster Service Department. The following information will be needed in order to assist you quickly and efficiently:

Model Number_____________________________________

Serial Number______________________________________

Nature of the

Problem___________________________________________________________________

Also any other information which may be helpful in solving your service problem.

RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE.

IF THE HCP IS INSTALLED WITH THE COUNTERTOP OPTION, ENSURE THE AREA

WHERE THE HCP BASE AND COUNTERTOP MEET IS PROPERLY SEALED WITH

A FOOD GRADE TYPE SEALANT.

1-2

HCP

HCP Software Quick Start

Using the HCP software requires food items be established in a food library, menus to be established and cabinet configurations to be set, which are built from the menus. The software is loaded with generic items.

Restaurant-specific items will need to be added.

Below is a quick look at this process with references to more detailed instructions and examples elsewhere in the manual.

Follow these steps to begin working with the HCP software:

Turn the Palm Pilot On and tap the HCP icon on the Palm display. See Section 5.

Tap the Key icon in the top menu bar of the software. See Figure 2 and Section 5.1.

Enter manager (all lower case) in the password dialog box. See Figure 1 and

Figure 1: Tap the key icon

(see arrow) and enter manager.

Figure 1: Using the Add and Edit buttons in the

Food Library column allows the creation of items for the Food Library. section 5.1.

Tap the Language button on the software interface and change the language setting from Default to English. See section 5.1.

Tap the Add button in the Food Library column. See Figure 3 and Section 5.2.

Figure 3: Menus 1-5 are populated by highlighting items in the Food Library and copying them to the desired menu.

Figure 4: Cabinet configurations are built on the screen of the Palm by first choosing a Menu and then selecting a slot for each item, which are chosen with

Tap the Edit button in the Food Library column. See examples in Section 5.2. the pull-down at each slot position.

Use the keyboard to name and edit items in the food library. See examples in Section 5.2

Build menus for Menus 1— 5, by moving items from the Food Library to the desired menus. See

Figure 4 and Section 6.2.

Configure cabinet arrangements by choosing items from the cabinet graphic pull-down menus, establishing a cabinet for each menu, 1 — 5. See Figure 3 and Section 6.2.

Beam the configurations to the cabinet. See Section 6-3.

2-1

HCP

3 Power Up

ALL ELECTRICALLY OPERATED APPLIANCES MUST BE ELECTRICALLY

GROUNDED IN ACCORDANCE WITH LOCAL CODES, OR IN THE ABSENCE OF

LOCAL CODES, WITH NATIONAL ELECTRIC CODE, ANSI/NFPA NO. 70-1990.

A. Power Requirements:

• Voltage – 208/240 VAC

• 2620 Watts @ 208V – 3420 Watts @ 240V

• Frequency – 50/60 Hertz

• Single Phase

• 20 amp Service

THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG GROUNDING PLUG FOR

YOUR PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED INTO A

PROPERLY GROUNDED THREE-PRONG RECEPTACLE. DO NOT CUT OR REMOVE

THE GROUNDING PRONG FROM THIS PLUG.

B. Plug the HCP into the power source.

C. Place the power switch in the ON position. All control displays will illuminate green approximately 2 seconds after the power switch is activated.

D. Monitor the temperature of the slots. The time it takes the slot(s) to heat from ambient (room) temperature to a 155

°F (68°C) setpoint should be approximately 15 minutes. It should take approximately 25 minutes to reach a 200

°F (93°C) setpoint. If setpoint is not consistently achieved within these limits, call your local Factory Authorized Service Center for repair.

3-1

HCP

4 Operational Overview

The HCP is available in two and four-slot models. Each slot has a controller, which indicates product and holding time for each of three tray positions within a slot. The controller has a timer button for each tray position, a menu button and a temperature display button. Individual buttons are annotated below. There are two trays available, a high-side model, 816-0727, and a low-side model, 816-0726.

There is a rack insert for the low-side tray, 803-0370.

Timer button

Power Switch

Menu button Temperature button

IR Lens

Timer LEDs

Figure 1

4-1

HCP

4.1 Cabinet Operation

1. Turn the power switch ON.

2. The displays will light and show

LOW TEMP.

3. Press the Menu key to scroll to the desired menu, release the key and immediately press the

Temperature key. The chosen menu is locked in. Menu or other setting changes require a Palm

Pilot PDA and related software. Programming the cabinet with the Palm is covered in Chapter 4.

4.2 Timer Operation

Press the timer key adjacent to the desired slot. The timer counts down from a preset value. The

display alternates between the product name and the remaining hold time. If more than one slot is holding the same product, the location with the least remaining holding time is indicated by a brighter display and illuminated dots.

Stopping the Timer

Press the timer key next to the slot position to turn a timer off. The timer stops and the display

dims, indicating inactivity. The use-first indicator moves to the next appropriate slot.

4.3 Cook More Prompts

The Cook More prompt sounds at a preset time prior to the expiration of the last tray of a specific product. No acknowledgement is necessary. The three-second audible alarm and the display of

COOK More serve as a reminder to cook more of the needed product.

4.4 Using Clean Mode

Press the Menu key repeatedly until

Clean Mode is displayed on the screen. Release the key and immediately press the Temperature key. Upload Palm will display. (This is a prompt to upload data captured by the cabinet during the day’s operation. Instructions for uploading data to the Palm are provided in Chapter 9.) Press the Temperature key again to display

Slot Cln Mode. This changes the setpoint for all slots to 125°F (52°C). The display will alternate between

SLOT CLN

Mode and Not Safe Yet until the temperature of the slots reaches 125°F (52°C). The display then dims.

Exit Clean Mode by pressing the Menu key until the desired menu choice appears. Release the key and immediately press the Temperature key; the choice is locked in. This must be done for each slot.

The display will show

Slot Temp Low until it reaches the setpoint for the chosen product.

4-2

HCP

4.4 Turning Slots OFF

Press the Menu key on a slot until

Slot Off is displayed. Release the key and immediately press the Temperature key; the choice is locked in.

4.5 Temperature Display

Press the Temperature key four times and the temperatures and setpoints will be displayed in this sequence:

4.6 Temperature Alarms

•

Top plate temperature

•

Bottom plate temperature

•

Top plate setpoint

•

Bottom plate setpoint

There are five temperature alarms:

• High Temperature

• Low Temperature

• FDA

• Sensor

• Rise Time

If an alarm condition occurs, an audible alarm sounds and the display alternates between the product selection and the alarm message. Timers cannot be started if a slot is displaying an alarm message.

4.6.1 High and Low-Temperature Alarms

If the slot temperature is above or below the limits for the product selected, the display will show

Slot temp high or slot temp low. An alarm will sound. Press a timer key to turn off the audible alarm. The audible alarm does not sound during initial cabinet startup.

4.6.2 Food and Drug Administration (FDA) Alarm

The FDA alarm indicates the slot temperature is below the preset limit to hold a product. An audible alarm sounds and the alarm message reads

Temp Under FDA. Press a timer key to turn off the audible alarm. The message remains until the slot temperature is within limits. Press the timer key to clear the FDA alarm.

4.6.3 Sensor-Range Alarm

The Sensor Fail alarm indicates a sensor temperature value above or below the 90-250°F (32-

121°C) range of the slot. An audible alarm sounds. The displayed message is

Sens

Alrm. Press a timer key to end the audible alarm. Service is required to correct the sensor alarm.

4-3

HCP

4.6.4 Rise-Time Alarm

A rise-time alarm indicates the slot temperature failed to reach operating temperature within a preset time after start up. The displayed message is

Slot Rise Rate. An audible alarm sounds. Press a timer key to turn off the audible alarm. Service is required to correct a rise-time alarm.

4.6.5 Additional Out of Tolerance Displays

HHH in the display indicates a sensor error. Service is required.

LLLL indicates a sensor error or a slot below 50°F (10°C). Allow the slot to operate for 10 minutes. If

LLLL remains, call for service.

4-4

HCP

4.7 Programming Overview

A Palm Pilot loaded with the HCP software is available. All programming of the cabinet, except initial default settings, is first entered into a Palm Pilot then beamed into the HCP.

Below is an annotated look at the main HCP screens on a Palm Pilot. Programming and use are covered in Chapters 5 and 6. See the Palm Pilot manual for a description of its operation.

Menu bar

Menu

Accesses cabinet configurations for breakfast, lunch and specials.

Tap Setup to reveal the menu bar, which is annotated on the adjoining page.

Food Library

Contains holding parameters for existing items and special items created by the user. Items are stored here and copied to a menu when needed.

The items are permanently stored in the Library unless erased by the user.

Edit

This function, which requires a password to open, allows the holding parameters of a food item to be changed. See

Chapter 5 for passwords.

Add

Used to create new food items. A password is required. See

Menu

Tapping this menu button reveals a display to rename, delete or create menus. Five is the maximum. A password is required.

See Chapter 5.

Menus 1 - 5

Food items are stored in a specific menu: Menu 1 –

Menu 5. The menu for a food item is selected here.

Menu column

Displays items available in the selected menu.

Chapter 5.

Copy

Tap this button to move items from the Food Library to a selected menu.

Language

Used to change the language displayed and change temperature display from Fahrenheit to

Celsius. A password is required. See

Chapter 5.

abc

Used to access a keyboard, which allows text entry and editing of menu items.

123

Used to access a number keyboard, which allows numerical entry.

Remove

Used to remove items from a menu.

Logs

Shows cabinet activity.

Figure 2

4-5

Menu bar

Tapping View produces a pull-down menu of selections. In many cases these items access features also accessible with buttons on the software interface.

Cabinet, which is not accessible otherwise, opens a menu for changing the setup of the cabinet from two to four slots. It also provides access to the menu for calibration and readdress, features used by technicians.

HCP

Figure 2

4-6

Menus

Accesses cabinet configurations for all menus.

HCP

Menu

Indicates menu on the Palm from which food items are being selected. It will also be the name of the cabinet configuration beamed to the HCP.

i

This is the preset icon and is tapped to gain access to stored cabinet configurations.

Transfer

Used to transmit or

“beam” cabinet configurations from the Palm Pilot to the

HCP cabinet.

abc

Used to access a keyboard, which allows text entry and editing of menu items.

Figure 3

123

Used to access a number keyboard, which allows numerical entry.

Cabinet Display

Shown anytime a menu is chosen from the Menu pull-down in the top right corner. Food items for slot positions are chosen by tapping on the triangle in each slot window.

Receive

This is used to download configurations and logs of daily cabinet activity.

4-7

HCP

5 Opening the HCP Software

Figure 1: Select the HCP software from the Palm's Utilities.

Figure 1: Entering a password allows new products to be added and existing products to be edited.

Figure 2: Set the Language selection from Default to English after tapping the Language button.

Figure 2: HCP software opens to its Setup screen..

Turn the Palm Pilot ON and tap on the software menu item (likely to be All) displayed in the right top corner.

A drop-down menu lists groupings of software and other functions.

Highlight Utilities by tapping on it. See figure 1.

The HCP icon shows on the screen. Tap it.

The Setup screen is displayed. See

figure 2.

5.1 Entering A Password/Choosing Language

The HCP software is provided with only one food item, chicken.

Additional menu items must be added by the end user. Adding, editing or removing items in the Food Library and changing the temperature display require a password. Tap the Key icon in the top center of the HCP software. Upper arrow in Figure 1. The Security

Manager screen appears.

Tap the abc icon in the bottom left of the screen. Lower arrow in

Figure 1.

Use the keyboard screen that appears to enter the required password

(manager) and tap OK.

The Security Manager screen reappears with the password in place.

Tap OK.

A Current Security screen appears. Click OK.

Tap the Language button and choose English as the language in the

Localization dialog box. Click Quit.

With the proper password and language entered, menu items can be entered and edited.

Exit the HCP software by tapping the House icon on the Palm screen, which will cause it to default to the Cook password setting upon restart.

5-1

HCP

5.2 Entering Menu Items

Step 1: Enter a password as described in section 5.1. Menu items are added by clicking the add button in the Food

Library window. See arrow.

Step 4: Tap on the line next to the abbreviated name. Then tap on the abc icon in the corner of the Palm window (see arrow).

Step 2: NewO appears highlighted in the Food

Library window. With the

NewO item highlighted, tap the Edit button.

Step 5: Use the backspace key to eliminate the NewO item text. Tap on the keys to enter an all-capital, four-letter abbreviated name for the product. Hit Done. Repeat these steps to enter a description.

Step 3: The Edit Food Item menu appears. It allows the product to be named and holding temperatures, times and prompts to be entered.

Step 6: Tap next to the underlined temperature settings and then tap on the number icon in the bottom right of the Palm display. A numeric keypad is displayed. Use it

— just as the keyboard is used in steps 4 and 5 — to enter setpoint temperatures, set hold time, cook more time and countdown lights.

5-2

HCP

Step 7*: Use the vertical slider on the right side of the screen to access four more options and adjust them for the new product.

Tap OK and the new item is stored in the Food Library and can be moved to a menu for transfer to the HCP.

5.3 Changing Menu Name/Deleting Menus

Step 1: Go to the menu window by clicking the

Menu… button in the right column of the display. See arrow.

Step 2: The Menu

Configuration screen is displayed. Highlight a menu to be deleted by tapping on it. Tap the

Delete button to eliminate the highlighted menu.

Use the New button to create a new menu. Tap on the Abbr: field and then tap the abc icon to access the keyboard to enter a name for the new menu item. Repeat to enter a menu name and description.

Tap the Save button to save the new menu.

5-3

NOTE: The new menu item will have to be populated by moving items from the food library to the new menu, a process described in section 6.2.

HCP

6 Programming the HCP

Receiving lens

A PDA with HCP software installed must be used to alter or add to the menu items stored in the HCP cabinet.

A Palm Pilot with the software loaded is available (106-6658) for the HCP.

Other Palm models can be used, however, they must have version 4.0 or later of the Palm operating system.

Figure 2

The Palm and its HCP software make setups for promotional items and special configurations easy to build and repeat. Cabinet configurations and daily cabinet activity can be uploaded from the

HCP to the Palm.

With the proper security clearance, menu items can be created and

Figure 1: Palm Pilot with HCP software displayed. edited in the software. Figure 1.

The new items, along with existing products, are stored in the Food Library, where they can be moved to the Menu and beamed into the HCP cabinet. The configurations established in the Palm

Pilot are beamed into the HCP cabinet’s lens. See figure 2.

6.1 Setting the HCP Software for 2 or 4-Slot Operation

Step 1: Tap the setup icon in the top left corner of the screen to reveal the menu bar and tap View and then choose Cabinet.

Step 2: In the Cabinet

Configuration screen’s pulldown menu, set the number of slots in the unit. The number of seconds the cabinet displays the product name and the remaining hold time can also be adjusted. See figure 2 on page 4-5 for accessing a keypad for numeric entry.

Step 3: Tap quit and the cabinet graphic reflects the change.

NOTE: A HCP-N box is displayed, however, that feature is not available.

6-1

HCP

6.2 Moving Products from the Food Library to the Menu

Step 1:NOTE: A password is required to alter the menu. See Chapter 5 for password entry. Tap Menu and a pull-down is displayed. Highlight a menu location by tapping it.

Step 2: Highlight the menu item in the Food Library by tapping on it once.

6.3 Setting Up the Cabinet on a Palm Pilot

Step 3: Tap the Copy button once and the item is copied into the Menu window and is available for loading into the HCP cabinet. The item also remains in the Food

Library.

Step 1: Tap Menu in the top right corner. The Setup menu is displayed. Choose Menu number by tapping on the word. In this example, Menu 1 is configured.

Note: These steps should be repeated to configure the cabinet for each menu. All five of the menu configurations are transferred to the cabinet each time menu changes are beamed into the HCP cabinet.

Step 2: A graphic of the HCP cabinet is displayed

Note: Graphics used in these instructions reflect the full-size

4-slot cabinet. Programming a

2-slot cabinet is identical, however, the graphic on the

Palm screen, with the changes shown in section 6.3, will reflect the cabinet being programmed.

Step 3: Tap on a leftmost slot and from the drop-down menu select a menu item (Entering menu items is covered in Section 5). Note: The leftmost slot positions establish the setpoint for that slot. Items with incompatible setpoints cannot be selected for adjacent positions.

Items are removed from a menu by highlighting them in the menu window and tapping the Remove button at the bottom of the menu display.

6-2

HCP

Step 4: Choose a product for each slot. All the products in a slot must have compatible setpoints.

Repeat these steps to configure the cabinet for each menu.

NOTE: All five of the menu configurations are transferred to the cabinet each time menu changes are beamed into the

HCP cabinet.

Step 5: The cabinet should now be configured for all five menus.

Step 6: Ensure the receiving lens on the front of the HCP cabinet is clean. Hold the

Palm Pilot parallel with the floor and aim it at the lens from no more than one foot away.

Tap the Transfer button.

Tap the TxirDa button.

The cabinet will beep and the

Palm Pilot will display a message, indicating a successful transfer. All five menus established on the

Palm are now accessible with the menu key on the HCP cabinet.

6-3

HCP

7 Saved Cabinet Configurations

The Saved Cabinet feature allows cabinet configurations to be loaded and stored permanently in the Palm Pilot. These configurations, reflecting daily, weekend and special menu setups for all five of the menus retained in the HCP cabinet, can be recalled and beamed into multiple HCP cabinets.

This feature is useful to retain cabinet configurations for different stores and specials.

The cabinet configuration displayed on the Palm must be changed when setting up special configurations for saving. To name and save the existing cabinet configurations in your Palm, follow the procedure below — beginning with Step 2.

Follow the steps below to enter the Saved Cabinet mode to create and store cabinet configurations.

7.1 Saving Cabinets

Step 1: When changes are made to the layout of the cabinet on the displayed graphic, the text by the i icon changes to (Modified). See arrow. This is a prompt that the layout has been changed. It is possible to save the new configuration.

Step 2: Clicking on the i icon displays the Saved Cabinets dialog box. The buttons are described below.

Open: Loads highlighted cabinet configuration.

Delete: Eliminates highlighted cabinet configurations.

Save: Saves new cabinet configurations to the saved cabinet box. Hit only after cabinet configuration has been named.

New: Starts process of saving cabinet.

Cancel: Exits program or aborts saving cabinet operation.

Step 3: Clicking New produces a date in the Name field and in the box, which stores named cabinets.

7-1

HCP

Step 4: Click in the desired field on the dialog box and click on the abc icon at the bottom left (see arrow) to display a keyboard for name and description entry.

Step 5: Use the keyboard to enter a name. Indicate in the name if the saved configuration is for a 2-slot cabinet when appropriate.

Click Done when complete. Repeat the process to enter a description.

7.2 Loading Saved Cabinets

Step 1: From the menu screen, click the i icon.

Step 2: Highlight the desired cabinet by clicking on the name.

Click the Open button to load the chosen configuration.

Step 6: Click Save and the date which appeared in Step

3 in the list of saved cabinets is changed to the entered name.

Step 3: The chosen cabinet configuration is displayed.

7-2

7.3 Deleting Saved Cabinets

HCP

Step 1: From the menu screen, click the i icon.

Step 2: Highlight the saved cabinet to eliminate.

Step 3: A dialog asks are you sure you want to delete the cabinet. Click

Yes if sure.

Step 4: The highlighted cabinet is removed from the saved cabinet list. Click cancel to leave the Saved Cabinet dialog box.

Highlight and load a saved cabinet, if desired, by highlighting the name and clicking Open.

7-3

HCP

8 Fahrenheit to Celsius

A password must be entered to change the temperature display. See

Password Access in Chapter 5.

The temperature display is accessed from the Language button on the Setup Screen. See figure 1. The temperature change takes place immediately after selection.

Figure 1: Arrow points to the

Language button, where the temperature display can be altered.

8.1 Changing Temperature Display

Step 2: Tap the Quit button.

Step 1: Enter the password as detailed in Chapter 5 and then tap on the Language button and the Localization window is displayed. Check Celsius to change the temperature range displayed to Celsius.

Step 3: Temperatures displayed when editing or adding menu items will be displayed in Celsius.

Repeat the steps, un-checking the

Celsius box, to change the displayed temperature range to Fahrenheit.

8-1

HCP

9 Uploading Cabinet Configurations and Daily Activity

Figure 1: To prepare the Palm Pilot to receive data from the HCP cabinet, tap the receive button.

The cabinet records daily activity and the data can be uploaded to the Palm each day prior to turning the cabinet off. This can be done at anytime. Also, the cabinet prompts for the data to be uploaded when the HCP is put in the clean mode. See Page 4-2.

A cabinet’s configuration can also be downloaded to the Palm.

Follow the steps at left and choose the Menu button. The cabinet displayed on the PDA should be saved before receiving a new configuration, which will overwrite the existing Palm display.

See Chapter 7 for instructions on using the Save Cabinet function.

Cabinet configurations received from two-slot units will alter that setting on the Palm. See Section 6.1 for instructions on setting up the software.

Figure 2: To download a cabinet's configuration, hold the Palm parallel to the floor and a foot away from the cabinet’s lens in the top right corner. Tap the RX Mnems button. To download a log of daily activity, tap the Rx logs button. A dialog box will display after the transfer is complete. Button names on later software versions may vary from what’s shown above.

9-1

HCP

10 Loading Software for the Palm

A Palm Pilot loaded with the HCP software is available from Frymaster as an accessory (Part # 106-

6658). HCP software, which can be loaded on a Palm PDA is a on a CD. A Palm operating system of 4.0 or higher is required to operate the software. See the Palm manual for instructions on installing, operating and deleting software from the Palm. Failed or outmoded HCP software must be removed from the Palm Pilot before new HCP software can be installed.

Instructions for checking the Operating System version are provided below for a Palm PDA. This information can also be found in the Palm manual.

10.1 Checking the Palm Operating System Version Number

System icon

Step 1: From a main screen, tap on the time display in the left top corner of the screen or the System icon in the bottom left. A drop-down menu is displayed.

Step 4: The version number is shown at the top of the display.

See arrow. Version 4.0 or higher is required to operate the

HCP software.

Step 2: Tap on Info.

Step 3: From the displayed menu, tap

Version in the bottom of the display. See arrow.

NOTE: Operating system updates are available at Palm’s Web site. However, not all Palm units can run the newer operating systems. Check your Palm manual and the Palm Web site, http://www.palmsource.com/palmos/ .

10-1

HCP

10.2 Loading Software on Palm

These instructions assume Palm desktop software is installed on your computer and a Palm with an operating system of 4.0 or higher is attached to the computer. Some familiarity with the Palm desktop software is also necessary. See the Palm manual for instructions on installing, operating and deleting software from the Palm. Failed or outmoded HCP software must be removed from the Palm

Pilot before new HCP software can be installed.

Step 1: Install the HCP software CD on your computer and copy the compressed

HCP file to your desktop.

Step 2: A self-extracting dialog box will be displayed. The Unzip to folder in the dialog box should show your

Palm add-on folder as the site it will be saved. If not, click the Browse button and navigate to that folder.

The Palm folder should be on your C drive and can be stored in the

C:\Program Files directory. The Addon folder is in the Palm folder. With the Unzip to folder showing the Palm

Add-on folder, click Unzip.

Step 1: A dialog box showing a successful extraction will be displayed.

Step 4: Open the Palm Desktop software by clicking on the icon on your computer's desktop and click the Quick Install button. See

Arrow.

Step 5: The Install Tool is displayed. Click the

Add button.

10-2

HCP

Step 6:The Palm’s Add-on folder should open. If not, navigate to it by clicking the folder icon. See Arrow. When the Palm folder is visible in the dialog box, double-click it and its contents will be displayed.

Step 8: The Install Tool is displayed with the highlighted HCP files. Close this box.

See arrow.

Step 10: Press the

HotSync button on the

Palm’s cradle. The

HotSync Progress dialog box is displayed. A

HotSync successful transfer message will be displayed on the Palm’s screen.

Step 11: Turn on the

Palm. You will find the

HCP icon in the Utilities menu. Click it.

Figure 7: Double-click the Add-on folder and its contents are displayed. Hold down the control key and single-click all files in the folder with a HCP prefix. Click Open.

Step 9: A new Install Tool dialog box will be displayed, saying the files will be installed when a HotSync is performed. Click OK.

Step 12: It is necessary to enter a password and change the language display from Default to English at the completion of the software installation. See Chapter 5 for password entry language choice instructions.

Setting the software for 2 or

4-slot operation is covered in

Chapter 5.

10-3

HCP

Step 1: Place Palms head to head as shown. Delete any earlier version of the

HCP software from the receiving Palm.

In the unit which contains the HCP software, tap the time display (top left) or the System icon

(bottom left).

10.3 Beaming Palm Software Between Palms

The HCP software can be beamed, or transferred, from one Palm to another by merely placing the units head to head and choosing Beam from a drop-down menu. Follow these steps to beam software between units. See the Palm manual for instructions on installing, operating and deleting software from the

Palm. Failed or outmoded HCP software must be removed from the Palm Pilot before new HCP software can be installed.

Step 2: Highlight

Beam in the pulldown menu that is displayed.

Step 3: The

Beam dialog box is displayed.

Highlight the

UHC software.

Tap the Beam button.

Step 4: The Palm will search for and find the adjacent Palm and beam the software and data. A success message will be displayed when the transfer is complete.

Step 5: Food items will not be visible in the Food Library.

Change the password. (See

Password Entry in

Chapter 5.)

Tap the Language button and change the language choice from Default to

English.

Setting the software for 2 or 4-slot operation is covered in Chapter 6.

NOTE: On some Palms with older operating systems, it may be necessary to beam the software with the HCP program open.

With the Palm Pilots arranged as described in Step 1 above and the HCP software displayed, follow these steps:

•

Tap the Setup icon to reveal the menu bar. Also see Figure 3, Page 4-6.

•

Tap View to reveal the drop-down menu shown at left.

•

Tap Beam Settings.

The Palm receiving the program will beep during the process and it will be necessary to tap a Yes button during the process to continue the transfer on both

Palms.

10-4

THIS PAGE INTENTIONALLY LEFT BLANK

Frymaster, L.L.C., 8700 Line Avenue, Shreveport, Louisiana 71106

TEL 1-318-865-1711 FAX (Parts) 1-318-219-7140 FAX (Tech Support) 1-318-219-7135

PRINTED IN THE UNITED STATES

SERVICE HOTLINE

1-800-551-8633

Price: $6.00

819-6213

NOV 08