PSB series
Power Supply Unit
Features
Input: 110~120 VAc
( or 230~240VAc
)
.
Strong power output even enough for large load.
LED indicates power supply status.
Build-in triple section fuse protection
Each output is protected by individual PPTC
Build-in backup battery Charger for uniterruptible.
Tamper Switch Protection.
12VDC case Size 24VDC case Size
Statement
Gianni power supplies are housed in a robust, compact wall mounted steel fabricated case with lift-off hinged front panel. In the event of a mains power failure, standby power is automatically provided from battery charging output.
Specifications
PSB-1A PSB-2A PSB-3A PSB-5A
Input
Output
12 VDC
LEDs indicate
24 VDC
Build in triple section fuse protection ( PPTC )
Output contact port
12VDc case Size
2 LEDs
1
) ( ) (
1 LED Power status
2 LEDs
) (
1
) (
2 LEDs
2 LEDs
( )
3
( )
2 LEDs
2 LEDs
( )
5
( )
24VDccase Size
Build-in backup battery Charger
( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
Tamper Switch
*Optional: Tamper Switch: When housing case is opened, the tamper switch will switch to N.O.
(
Normal Open
*
)
Battery charger and may accommodate up to 2 batteries that provide continuous operation of access controls and locking hardware during a power failure.
*2 LEDs, Power (Yellow), Charge(Red),No power status(Green), Charge supply(Red)
GIANNI INDUSTRIES, INC.
No. 13, Zhong Sing Road, Tu-Cheng Industrial Zone,
Tu-Cheng City, Taipei, Taiwan 23678
Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876
E-Mail: [email protected]
Website: gianni.tw
Copyright 2008 Gianni industries, inc. All rights reserved.
DM-CA-PSB Ver. D Published on 2008.08.12
The products are manufactured under an ISO
9 0 0 1 & Q C 0 8 0 0 0 0 C e r t i f i e d Q u a l i t y
Management Program environment back its product quality, performance and commitment to customer satisfaction.
Application
Power
Lock
Device
*
Reader
(outdoor)
Push
Bar
Door
Loop
PSB series
Power Supply Unit
PSB3A-2A-115
PSB3A-2A-230
To switch DC output screw fastened:
Optional Accessories
PSB-TAMPER
Tamper Switch
1.Status LED specifications
- Power:
Yellow: Both AC input and DC outputs are at normal status.
Green: There is no AC input, and the power is supplied by the batteries.
Red: There is no output voltage.
- Charge:
Red light on: The batteries are charging.
Red light off: The batteries are finished charging. (If the light is off immediately after the power is on, there may be some damages with the batteries).
2.Installation specifications
- There is always voltage output between the OUTPUT 1~2.
When the TAMPER is at N.C, there is voltage output between the OUTPUT 3~5, and when the TAMPER is at N.O, there is no voltage output.
- Each OUTPUT is protected by individual PPTC from over current; therefore each load of output may not exceed 1AMP.
- TAMPER switch: system on-off push switch mounted on outside cover. When outside cover is close, TAMPER switch is on N.C; when outside cover is open, TAMPER switch is on N.O.
For series connection at ''L'', it will disconnect the main power for 230Vac.
For parallel connection at the TAMPER, it will control the output between the OUTPUT 3~5.
GIANNI INDUSTRIES, INC.
No. 13, Zhong Sing Road, Tu-Cheng Industrial Zone,
Tu-Cheng City, Taipei, Taiwan 23678
Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876
E-Mail: [email protected]
Website: gianni.tw
Copyright 2008 Gianni industries, inc. All rights reserved.
DM-CA-PSB Ver. D Published on 2008.08.12
TAMPER SWITCH
(option)
(PSB-5A)
OR
Main Input
F U S E
Main Input
When housing case is opened, the tamper switch
Warranty
The product is warranted against defects in material and workmanship while used in normal service for a period of 1 year from the date of sale to the original customer. The GEM policy is one of continual development and improvement; therefore GEM reserves the right to change specifications without notice.
The products are manufactured under an ISO
9 0 0 1 & Q C 0 8 0 0 0 0 C e r t i f i e d Q u a l i t y
Management Program environment back its product quality, performance and commitment to customer satisfaction.