advertisement
▼
Scroll to page 2
of 8
Trouble-shooting SEMI AUTO WASHING MACHINE If the laundries fall to the outer side of the spin tub AWT-80LI If the laundries fall to the outer side of the spin tub, Please contact the after-sales service department. (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomena The machine does not function. The reason Is there power failure? Is the power plug loose? Is the pulsator twisted by foreign materials? How to settle Use it when the power is on. Insert the power plug tightly. Remove the foreign materials? USER WASHING MACHINE The draining does not function Has the drain hose being laid down? Is the drain hose blocked by foreign material? Are there any laundries trapped at the outer side of the spin tub? There's abnormal sound during washing Are there hair pin, coins or meta items brought inside the tub? There's abnormal sound and violent vibration during spinning Is the machine slanting? Is the gland pressed evenly? Are there any laundries trapped at the outer side of the spin tub? Are the laundries in spin tub over loaded? 14 Manual CONTENTS Put down the drain hose? Remove the foreign material? Please contact the after-sales service department. Remove the hair pin, coins or metal items Pressed the gland evenly Level the machine properly. Remove the laundries Remove a little laundries Packing list Specification Names of the parts Safety precautions Installation and adjustment Preparation before washing Do s and don ts Usage of the detergent Washing sequence Maintenance Trouble-Shooting Packing × ° list Ï ä Ë µ à ÷ Quantity Name One piece User's manual Water inlet hose One piece Gland One piece One set Specification × ° Ï Ã ä ÷ Ë µ Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1). Corrugation Pipe Figure 1 4. Install the overflow filter. (1).Install the corrugation pipe. (2).Insert the mounting plate at the bottom of the filter into the valve cover. (3).Hang up the hook at the left upper side. (4).Push the upper part in as indicated in Figure 2. Hook Figure 2 Ï ´ º ó ´ ¦ À í Disposal of the complete unit 220V 50Hz Water level Water quantity estimated (L) Maximum/58 Medium/49 Minimum/43 The Rated washing capacity(kg) 8.0 The Rated spinning capacity(kg) 6.0 Injection pressure(MPa) 0.02~0.2 Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty Do not wash it directly by water Alcohol * Water level adjusting lever 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. Semi Auto washing machine Rated voltage frenquency Ï ´ º óó ´´ ¦¦ ÀÀ íí Specifications may be subject to change without prior notice Petrol Thinner After washing, dismount the water inlet hose. Do not store water in the tub for long period. Discharge the water immediately after each using. Pull off the power plug and hang up the power cord. Hang up the drain hose. Wipe off the water drops on the surface and inside the tub with clean soft cloth. Open the cover of the wash tub and the inner/outer cover of the spin tub for some time (about one hour), then close them. 13 Ï´ ´º ºMaintenance ó´ ´¦ ¦À Àí í Ï ó Names of the parts After using, please clean the lint and eyewinker of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. It must be cleaned in time after each using. 1. Take off the lint filter Put hand at the indicated position. Push down to take it off. ( See Figure 1) 2. Clean the lint Put it in water and clean while it is still wet.(See Figure 2) 3. Install the lint filter After cleaning, insert the bottom Figure 2 of the lint filter ( marked with "down side") into the overflow filter , then push the upper part of the filter in ( marked with " up side "). (See Figure 3) Figure 1 Meaning and description of the symbols Warning sign Figure 3 Cleaning the overflow filter Too much lint on the overflow filter will influence the normal usage of the machine. Please clean it every two months. Elastic fixing Take off the overflow filter. claw As indicated in the figure, nip the elastic fixing claw and pull it to the direction of the arrow to take it off. 12 Forbidding sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the personal safety of the user. Contents marked with that symbol are actions forbidden to perform. Performing of those actions may result in damage of the machine or injure the personal safety of the user. Please check if the power receptacle has good earthing condition before using to guarantee your safety. 1 × ¢ ÒSafety â Êprecautions Â Ï î Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector. When the machine is normally using, please put the power plug at the location easily to be inserted and extracted by hand. Be sure to pull the plug off when there's power failure, or the machine is being moved, cleaned or when it is idle. Spinning 1.Put the laundries into the spin tub evenly and smoothly. Earth If the supply cord is damaged,it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 2.Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3.Spin Select suitable spin time according to the laundries, and do spinning. Do not use water hotter than 50 C . Do not put the machine at damp place like the bathroom . Never wash it with water. Do not place wet laundries on the control panel. During spinning, if there is abnormal sound, it is generally owing to slanting placement of the laundries. Please stop the machine and reorder the laundries. In spinning, it will pause the work if you open the outer cover of the spin tub. Close it to resume the spinning. For washing machine with ventilation openings in the base, that a carpet must not obstruct the openings. Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations. Ventilation hole at the bottom of the washing machine To do spinning and draining and rinse with water-filling together, please first do spinning for around 1 minute, then do draining or rinse with water-filling . Otherwise the spinning will stop owing to too much water stored in the spin tub. Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use the plug any more. 2 11 × ¢ ÒSafety â Êprecautions Â Ï î Rinsing Rinse with water-filling Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not decompose, repair or alter the machine by yourself. 1.Put the laundries Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing. Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine. Do not wash laundries with volatile materials (such as thinner, petrol etc.). l Petro Thinner Rinse with stored water (Repeat the midway spinning and rinsing with stored water for 2-3 times) Keep the machine away from direct sunlight and heat source like the heater. Handicapped or children without care shall not use the machine. 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is few, please use "Standard" current. If you use "Strong" current, it may splash. 10 To protect your laundries and washing machine, please take out all of the coins, buttons, sand, hairpin and other foreign materials before washing. 3 Please check if the connection of the water inlet pipe is proper. It is suggested to use foamless washing powder. Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Midway spinning Install the lint filter 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. After opening the package,please take out the lint filter from the document bag,install it to the overflow filter of the wash tub.See to the figure. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Overflow filter Lint filter Usage of the drain hose The drainage shall be smooth with the drain hose. Proper 1.The height of the drain hose shall be less than 10cm , or the drainage will not be smooth enough and cause incomplete drainage. <10cm Proper The laundries are slanting (2) Close the inner and outer cover of the spin tub. (3) Spin for 1-2 minutes. Outer cover of the spin tub Inner cover of the spin tub 2.Do not tramp or press the drain hose. 3.If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. 3.Run the foam-removing spinning. 1 Set the inlet selector handle on spin side and 4.If extra drain hose is needed , please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m. Water inlet Inlet selector handle fill water for about 1 min. In case water flows out from wash tub side due to too much inflow, please turn down > 30mm <1.5m the water tap a bit. 2 Close the spin tub outer cover and spin for about 1 - 2 min. If the extra hose is too long, cut it either at point A or B. A 4 No gland B 9 Wash Spin Washing sequence Wash selector Wash timer (To set to below 2 minute, first set to 5 minute then turn it back. it can increase the service life of the timer). (Strong current, standard current) How to change the direction of the drain hoses Spin timer (to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer). OFF STANDARD 3 15 5 1 4 2 DRAIN 12 6 SPIN TIMER WASH SELECTOR WASH TIMER 9 3 Âé Wash 1 Inlet selector (1) Set inlet selector to Wash side. Figure 1 (2 )Adjust water level rod to a position as needed. WASH SPIN Figure 1 2. Fill the water and add the dissolved washing powder to make the water level reach the preset position. (Figure 2) Run washing program for some time to stir and dissolve the powder completely. Figure 2 STRONG STANDARD DRAIN 3.Put in the laundries. If the water quantity is insufficient, please add water. 4.Select the current. Select the strength of the current according to the laundries. (Figure 3) 5.Select the washing time Select the washing time according to the laundries. (Figure 4) Figure 3 Drain hose Take off the drain hose Figure 1 Drain hose fixing hook Rotate the fixing hook for 90 Take off the fixing hook downwards Figure 3 Figure 2 Rotate the fixing hook for 90 to fix it Insert the fixing hook into the installation hole upwards Figure 4 Extend the drain hose from the back side Take out the drain hose from the two fixing hooks. make it extend towards back side.(Extend the drain hose from the side of back, hang the drain hose in to the hanging hole at the both sides) . (As per Figure 6). Figure 5 Figure 6 Install the water inlet hose; Select the water level 15 3 12 6 9 Figure 4 STANDARD DRAIN Figure 5 8 Take off the drain hose from the hanging hole of the cabinet. Pull the drain hose fixing hook outwards gently to take out the drain hose from the two fixing hooks. (As per Figure 2) Rotate the drain hose fixing hook for 90 to take it out from the installation hole (As per Figure 3). Install the two drain hose fixing hooks taken out into the installation hole at the other side of the base frame (to aim at the installation hole accurately you can lean the washing machine forward slightly).Then rotatefor 90 (As per Figure 4). Pull the fixing hook outwards slightly. Inlay the drain hose into the fixing hooks reliably along the groove at spin tub side, and make it extend towards spin tub side.. Then hang the drain hose into the hanging hole at the spin tub side. (As per Figure 5). Fixing hook installation hole Pull outwards slightly OFF STRONG 6.After washing,the buzzer will ring .Set the "WASH SELECTOR" at "DRAIN". (Figure 5). Side sectional view Drain hose fixing hook Extend the drain hose from the side of spin tub. STRONG OFF Figure 1 indicates the ex factory installation position of the drain hose. Insert the water inlet hose into the water-filling entrance on the control panel directly.(pull it out to dismantle it) Select water level according to the quantity of the laundries. Set the water level adjusting lever to needed line. Use the new water inlet hose provided with the machine to connect to the water faucet.Old hose sets should not be reused. 5 Water inlet hose Water level indicator Maximum Medium Minimum Max. Med Min Ï ´ ÇPreparation ° × ¼before ± ¸washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose . 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally. Clear the Tie the long pocket. Take strips; fasten out the coins, the buttons; sand, hairpins close zippers. etc. The quantity of the laundries shall not be too large. Stretch and loosen the laundries before putting them in the tub. When the pulsator is running , the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries. a. Check if the laundries are applicable for washing with machine. b. Divide the laundries that are not colorfast from other laundries. c. Put those laundries difficult to absorb water into water with hand. d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent on them in advance, which can make it easier to remove the soil. e. For those laundries that may get lint ball and those with long fur, turn it over before putting in. f. Do not put those laundries polluted by chemicals into the washing machine directly. 6 The capacity of washing and spinning of the machine refer to the weight of the standard laundries under dry condition that can be washed or spinned in one time. the largest capacity is only the loading capacity of the drum The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put in reasonable amount of laundries and the laundries can be turned round in washing for one time washing. Do not select " Maximum " water level for laundries less than 1.5kg, so as to avoid splashing of water. It is suggested not to use high sudsing detergent. Ï ´ µ Ó Î ï µ Ä ² Î ¿ ¼ Ö Ø Á ¿ Usage of the detergent Pay attention to following before washing the laundries Check if the laundries has special requirement on washing Ï ´ µDoÓs and Ð ëDonÖtsª How to use the washing powder How to use the whitener Ï ´ µ Ó ¼ Á µ Ä Ê ¹ Ó Ã Direct dissolved in the machine: 1.Fill small quantity of water. 2.Add the powder . Run for 30 seconds to dissolve it completely. 3.Put in laundries. Select suitable water level. Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laundries with color or pattern as they are prone to lose color. The instant dissolving of the washing powder: 1.Prepare warm water of 30 C and a container. 2.Add the powder while stirring to fully dissolve it. The powder is more prone to pollute the laundries than the detergent. Therefore please use it with proper quantity. Dosage of different washing powder is different. Please refer to the instruction of the washing powder for the detail dosage. The whitener shall not touch the laundries directly. Refer to the user's manual for the usage and quantity of the whitener. For powder whitener, please dissolve it before using. 7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement