Quick Start Guide
Important:
1. You must charge the battery for at least 2½ hours prior to the first use.
2. Maximum battery capacity is first reached after completing three complete charge and discharge cycles.
3. Always use Genuine Psion Teklogix Media to ensure optimal performance.
• To load media:
• Move the Paper Door Release in the direction indicated in Figure A and open the Paper Door.
• Roll Feed - Move the media support as shown in Figure B and place the roll between the supports. Make sure the media rotates
freely. Lay the leading edge of the media through the print head as shown in Figure C, and close the door.
• To install the battery: Slide the battery into the battery compartment until the release lever on the battery snaps into place.
You may remove the battery by pressing the release lever toward the bottom of the printer and pulling the battery out of the battery compartment.
• To charge the battery, connect a power adapter (sold separately) to the appropriate power source and plug the output cable into the printer’s Power Connector as shown in Figure A. The Battery Indicator will turn on indicating that the battery is being charged.
• To perform a self test, press and hold the Paper Feed Button while turning on the printer with the Power Button.
Note: For more information, refer to the MLP3040 Series Operator’s Manual.
Paper Supply Gauge Paper Door
Figure B
Media Support
Paper Leading Edge
Serial I/O Connector
Tear Bar
Power Connector
Magnetic Card Reader
Figure C
Release Lever
Figure A
Power
Paper Feed
/Advance
Paper Door
Release
Battery
Message Window
Printer Setup
Many of the printer’s features may be set using menus available on the front panel of the printer.
To enter the Setup Mode, press and hold the Enter Button while turning on the printer with the Power Button. Continue to hold the Enter Button until “Menus Active” is displayed.
While in Setup Mode, the power indicator will blink slowly. Upon entering Setup Mode, the FORMAT MENU is shown first. To advance to the INTERFACE MENU or OPTIONS MENU, press the Advance Button.
When in Setup Mode, the current menu item is shown on the top line, and its corresponding value is shown on the bottom line. To increment the value on the bottom line to the next setting, press the Increment Button. To advance to the next menu item, press the
Enter Button.
To exit Setup Mode, press the Advance Button until “Exit Setup” is displayed. Press the Enter Button to save the changes and return to normal printer operation.
Power
Increment
Indicators:
IrDA Window Enter Paper Feed
/Advance
Power On = Ready to print, Slow Flash = Setup Mode,
Short Flash = Power Saving Stand By Mode.
Wireless I/O Enabled and Connected.
Magnetic Card Reader: Ready for swipe.
Error: See messages, below.
Battery: On = Charging, Flashing = Battery Low.
M
E
N
U
I
T
E
M
S
Printer Setup Menus
FORMAT MENU
Up to 5 formats can be stored
Format Name
Up to 16 Characters
+
Font
SansSerifA
4.2, 5.5, 10.2, 10.7, 16.9,18.5, 20.3;
Courier
12.7, 13.5, 14.5, 15.6, 16.9*,
18.5, 20.3, 22.6, 25.4
Spacing
0 - 10, 3*
Left Margin
0* - 1.0244”
Right Margin
0* - 1.2608”
Print Contrast
-75 to +125, 0*~
Max Paper Speed
0.32 to 3.30*~ ips
Form Feed Distance
0 – 2.5216”, 1.2608*~
Mark Sensing
Front*, Back~, Gap
Mark Sensitivity
-10 to +10, 0*
Gap Sensitivity
-10 to +10, 0*
Tear to Mark Dst
-0.7092” to 1.7927”, 0*
Present Distance
0.0000”* to 1.2911”
• Use the Advance Button to access the next menu. (Also see + note below)
• Use the Increment Button to increment the value displayed on the bottom line.
• Use the Enter Button to accept the value displayed and advance to the next feature.
INTERFACE MENU (IrDA, Bluetooth, or Wi-Fi are only available if that option is installed)
Paper Related Messages:
Paper Door Open - Close paper door and press the Paper Feed Button to continue.
Paper Fault - Insert paper or correct jam and press the Paper Feed Button to continue.
Emulation
Psion Teklogix*, O’Neil,
ZPL-II, Mt3, CPCL
Hex Dump
Baud Rate
9600, 19200,
38400, 57600*
Data Bits
7, 8*
Stop Bits
1*, 2
Parity
Emulation
Psion Teklogix*,
O’Neil,
ZPL-II, Mt3,
CPCL,
Hex Dump
Emulation
Psion Teklogix*, O’Neil,
ZPL-II, Mt3, CPCL,
Hex Dump
Pairing Mode
Paired*, Unpaired
Role Policy
Defer*, Master
Discoverability
On*/Off
Pin
0*, Up to 16
Numeric Chars.
+
Emulation
Psion Teklogix*, O’Neil, ZPL-II,
Mt3, CPCL, Hex Dump
WLAN Type
Infrastructure*, Peer-to-Peer
WLAN Channel
1* – 14
WLAN SSID
any*
+
WLAN WEP Bits
0*, 64, 128
WEP Key 1-4
10 or 26 Char. Hex String
+
None*, Even, Odd
XON/XOFF
Off*, On
ETX/ACK
Off*, On
RTS/CTS
Off, On*
Security
Off*, On
Local Name
MtP300-Serial#*
Address
+
(Displayed Only)
WLAN Auth
Auto*, Open, Shared
IP Address Assign
DHCP*, Static
IP Address
0.0.0.0*
+
IP Subnet Mask
0.0.0.0*
+
IP Gateway
0.0.0.0*
+
Tunnel Port#
08023*
+
* Factory default value.
+ When changing value for this feature, use Advance Button to advance to the next
Magnetic Card Reader Messages:
Swipe Card Now - Magnetic Card Reader is ready for card to be swiped.
Card Read Ok - Card read successfully.
Card Not Read - Card not read correctly.
OPTIONS MENU
Max Format #
1* – 5
Auto Power Down
Off*, 1 – 15 Minutes
User Language
English*, French, German
Truncate Lines
No*, Yes
Print Promo
No*, Yes
Note: After exiting Setup, you may print the current
Interface settings by pressing and holding the Enter
Button until “Printing Setup” is displayed.
~ LP Model Defaults: Print Contrast = +35, Max Paper Speed = 2.30ips,
Form Feed Distance = Mark Sensing, Mark Sensing = Back.
