FD1500

AutoSeal

®

FORMAX

®

OPERATOR MANUAL

FIRST EDITION

1-800-658-8788 - www.abcoffice.com

TABLE OF CONTENTS

1500 Shown with Optional Stand

Page:

1. DESCRIPTION, UNPACKING AND SET UP

3.

4.

FOLD PLATE ADJUSTMENT, SETTING CUSTOM FOLDS

DAILY MAINTENANCE / TROUBLE SHOOTING

5. TROUBLESHOOTING

1-800-658-8788 - www.abcoffice.com

DESCRIPTION

Paper side guides

In-feed table

Top Cover

Upper Fold Plate

Control Panel

Lower Fold Plate

FUNCTION:

The 1500 Folder / Sealer folds and seals many different configurations including, "C", "Z", “V” and custom folds. It may also use several different sizes of forms. For configurations and / or paper sizes see listing under specifications below.

SPECIFICATIONS:

Maximum foldable paper size 14" length x 8.5" width

Fold styles "C", "Z", "V" and custom folds

Paper loading capacity

Machine Weight

Power Supply

Up to 100 sheets

82 lb.

120 volts, 50/60 Hz, 3.5 amps.

UNPACKING AND SET UP

1. Check package for shipping damage. If there is shipping damage, do not discard the box.

2. CAUTION: Two people must lift machine out of the box.

3. Remove the paper tray and insert into rails on bottom pan.

4. Plug cord into machine and into wall outlet.

1

1-800-658-8788 - www.abcoffice.com

CONTROLS

Start…………………Starts machine.

Stop…………………Stops machine.

Ready light…………Steady green when power is on

Blinks red when cover is open or fault is detected.

Counter Reset.........Resets counter if equipped.

Counter…………….Shows forms count if so equipped.

OPERATION

1. Adjust fold plates to desired fold for length of paper (see fold plate adjustment on page 3). To do this, loosen the two thumbscrews (figure 3a & b) on each fold plate. Align center bar (figure 3a & b) so the marks on each side match up. For “V” folds remove the lower fold plate, turn around 180 ° and reinstall.

2. Make sure fold plates and cover are reinstalled properly.

3. Plug in cord and turn power on (figure 1).

4. To make sure folds are in the correct location, push the paper feed lever (figure 2) down and place one form onto the in-feed table and press the start button. Adjust fold plates if necessary (see fold plate adjustment on page 3).

5. Push the paper feed lever down and load paper neatly stacked and squared on to the in-feed table.

Paper can be stacked up to 100 sheets. Note: Standard "Z" fold forms can be loaded face up or down with the glue edge leading. All

"C" fold forms must be loaded face up with glue edge leading.

6. Be sure the ready light is green and press the start button to begin operation.

(figure 1) (figure 2)

2

1-800-658-8788 - www.abcoffice.com

FOLD PLATE ADJUSTMENT

Upper Fold Plate Lower Fold Plate

Thumbscrews

Bar

(figure 3a) (figure 3b)

1. To adjust the first fold remove the top cover. If the first fold is too long loosen the two thumbscrews on the upper fold plate and slide the bar down. If the fold is too short loosen the thumbscrews and slide the bar up.

NOTE: The bar should be on the same marks on each side.

2. To adjust the second fold remove the lower fold plate. If the second fold is too long loosen the two thumbscrews and slide the bar up. If the fold is too short loosen the thumbscrews and slide the bar down.

NOTE: The bar should be on the same marks on each side.

3.

For quick setup of “C”, “Z” and “V” folds refer to the blue lines on the fold plate.

SETTING CUSTOM FOLDS

Eccentric "Z"

1. Measure the length of panel

"A"

2. Adjust the upper fold plate so that the bar lines up with the measurements of panel "A" i.e. if panel "A" is 5 1/4" long move the bar up or down so that it lines up with the 5 1/4" mark on the fold plate.

3. Measure the length of panel

"B"

4. Adjust the lower fold plate so that the bar lines up with the measurements of panel "B".

5. Load forms and press start

(refer to OPERATION on page

2).

Panel "A"

Panel "B"

Uneven "C" / Return Mailer

1. Measure the length of panel

"A" & "B"

2. Adjust the upper fold plate so that the bar lines up with the measurements of panel "A" &

"B" i.e. if panel "A" & "B" are 10

1/2" long move the bar up or down so that it lines up with the

10 1/2" mark on the fold plate.

3. Measure the length of panel

"B"

4. Adjust the lower fold plate so that the bar lines up with the measurements of panel "B".

5. Load forms and press start

(refer to OPERATION on page

2).

*

Extended fold plate is needed to process this form

Panel "A"

Panel "B"

3

1-800-658-8788 - www.abcoffice.com

DAILY MAINTENANCE

1. It is recommended to let forms cool for one-half hour, from the laser printer, before folding and sealing. This allows toner to set on the forms, and static electricity to discharge. The FD400 Jogger is recommend for best results. The Jogger squares the forms and dissipates heat and static created by laser printers.

2. If toner builds up on the metal sealer rollers clean the rollers with a lint-free cloth dampened sparingly with a mild household cleaner.

3. Clean in-feed wheels and fold rollers with Formax recommended roller cleaner & rejuvenator to remove paper dust and toner. A damp cloth with water is the best alternative. CAUTION: Do not use any chemicals other than the roller cleaner & rejuvenator or water.

TROUBLESHOOTING

A. Clearing paper jams:

WARNING:

Turn machine off and unplug cord from its receptacle

1. If a jam occurs in between the metal sealing rollers remove any remaining forms from the hopper. Remove the top cover and the upper fold plate. Remove the jam clearing tool (located under top fold plate), apply the tool to the upper metal roller (figure 4) and turn clockwise

(Caution: do not apply excessive force or rollers may be damaged) until the paper jam is clear.

Remove the jammed form and return tool in holder and reinstall the upper fold plate. Reinstall cover and press the start button.

Note: Press the black button (figure 5) near the power cord inlet to reset the breaker if necessary.

(figure 4) (figure 5)

2. If a jam occurs in the fold plates remove fold plate and remove paper. Reinstall fold plate.

TROUBLESHOOTING

4

1-800-658-8788 - www.abcoffice.com

B. Fold Quality Needs Improving

:

1. Make sure paper is squared and installed correctly. Side guides should be evenly balanced and snug against the paper.

2. If folds are still incorrect adjust fold plates (see fold plate adjustment on page 3).

C. Paper is not Folding Square (Skewing)

:

1. If paper pulls left or right adjust the skew adjuster. To adjust the skew, turn the skew adjuster (figure 6) left or right until the paper is feeding correctly.

(figure 6)

D. Ready light is not illuminated and power is on:

1. Press the black button (figure 3) near the power cord inlet to reset the breaker.

E. Ready light is blinking red:

1. Check to see that the top cover is installed properly.

2. Check to insure that the photo-eye, before the metal sealer rollers, is clear of forms and/or paper dust.

5

1-800-658-8788 - www.abcoffice.com