Martin JEM Roadie Compact User manual

P/N 35010027-D
Roadie Compact
user manual
Safety information...................................................................................................................... 3
Product overview ....................................................................................................................... 6
Product description................................................................................................................ 6
Features at a glance .............................................................................................................. 6
Product details ....................................................................................................................... 7
Connections........................................................................................................................... 8
Quick Start ................................................................................................................................. 9
Setting up............................................................................................................................... 9
Making fog ............................................................................................................................. 9
Installation and setting up ....................................................................................................... 10
Location ............................................................................................................................... 10
AC power ............................................................................................................................. 10
Setting up............................................................................................................................. 11
Final checks ......................................................................................................................... 11
Turning on the power........................................................................................................... 11
Control settings ....................................................................................................................... 12
Overview .............................................................................................................................. 12
Setting Fog density .............................................................................................................. 13
Setting Fan speed................................................................................................................ 13
Setting the Timer.................................................................................................................. 13
Setting the DMX base address ............................................................................................ 14
Setting the operating temperature....................................................................................... 14
Setting the control panel display brightness ....................................................................... 14
Setting the master-slave link mode ..................................................................................... 14
Aux option ............................................................................................................................ 14
Priming the machine after fluid out ...................................................................................... 15
Resetting options to factory settings ................................................................................... 15
Remote control ........................................................................................................................ 16
Overview .............................................................................................................................. 16
Functions ............................................................................................................................. 16
Connection........................................................................................................................... 17
DMX control ............................................................................................................................. 18
Overview .............................................................................................................................. 18
Connection........................................................................................................................... 18
DMX functions...................................................................................................................... 18
Fog fluid types ......................................................................................................................... 19
Basic service............................................................................................................................ 20
Cleaning............................................................................................................................... 20
Fuse replacement ................................................................................................................ 20
Troubleshooting ...................................................................................................................... 21
Status messages ..................................................................................................................... 22
Specifications .......................................................................................................................... 23
2
Safety information
Safety information
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the system only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Jem Service.
Preventing electric shocks
•
Always ground (earth) the machine electrically.
•
Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
•
Before connecting the Roadie Compact to power, check that the voltage
indicated on the machine’s serial label matches your local AC power
voltage. If your AC power voltage does not match, do not use the
machine. Contact Jem Service for assistance.
•
Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
•
If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine
and contact Jem Service for assistance.
•
Disconnect the machine from AC power before servicing and when not
in use.
•
This system is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.
•
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Jem for advice.
•
Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Jem.
Safety information
3
•
Do not operate the machine if any parts are damaged, defective or
missing.
•
Moisture and electricity do not mix. Do not aim smoke output at
electrical connections or devices.
Preventing burns and fire
•
The smoke produced by the machine is hot enough to cause burns
when it leaves the nozzle, and very hot droplets of fluid escape
occasionally. Keep people and objects at least 1 meter (39 inches) away
from the smoke output nozzle.
•
Do not touch the smoke output nozzles during or after use – they
become extremely hot and remain hot for several hours after the
machine have been shut down.
•
Smoke output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point smoke output at sources of
ignition such as open flames or pyrotechnic effects.
•
Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•
Replace fuses only with ones of the type and rating specified in this
manual for the machine.
•
Provide a minimum free space of 100mm (4 inches) around the
machine.
•
Provide a minimum free space of 500mm (20 inches) around fans and
air vents and ensure free and unobstructed air flow to and around the
machine.
•
Keep the machine at least 600mm (24 inches) away from combustible
and heat-sensitive materials.
•
Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
•
Do not operate the machine if the relative air humidity exceeds 80%.
Preventing injuries
4
•
Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
•
Do not install the machine over areas where people are present.
•
This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
•
Verify that the machine’s temperature setting is suitable for the type of
fluid in use whenever changing fluid or resetting the default menu
values.
•
Smoke machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.
•
Ensure at least 2m visibility in areas where smoke is being produced.
•
Smoke fluid contains food-grade glycols in solution but may present
health risks if swallowed. Do not drink it. Store it securely. If eye contact
occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.
Safety information
Preventing breathing problems
•
A smoke machine can operate safely only with the smoke fluid it is
designed for. Use the machine only with fluids specified under “Smoke
fluid options” on page 19 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the
machine.
•
Do not create dense smoke in confined or poorly ventilated areas.
•
Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to smoke output.
•
Do not point smoke output directly at a person’s face or at face height.
Safety information
5
Product overview
Product description
The Roadie Compact smoke machine from Jem provides a uniquely flexible and
convenient solution to a wide range of smoke requirements whether
permanently installed or, with the addition of the touring accessories, taken on
the road.
Featuring twin independent outputs and a high speed radial blower, the Roadie
Compact can quickly produce large volumes of fog to create large scale effects
in the biggest venues.
With variable-temperature heat exchangers, the Roadie Compact can use
multiple weights of fluid. Just about anything that can be done with smoke from an ephemeral steam chases to a dense, long-lasting “whiteout” - can be
achieved with the Roadie Compact.
Congratulations on your purchase of the Roadie Compact smoke machine from
Jem. Details of the full range of Jem products are available on our website at
www.jemsmoke.com.
Features at a glance
6
•
High speed radial blower
•
16A single phase supply
•
Twin independent block design for high output and reliability
•
Operates horizontally or vertically
•
Control panel with alphanumeric display
•
Optional full function digital remote with display (25m max cable length)
•
Durable 4” swivel castors
•
Carrying handles
•
Indirect fluid sensing system for unattended operation
•
DMX control (2 channels)
•
9.5 litre fluid container with easy remote fluid connection
Product overview
Product details
Control panel
Suspension rigging
points
Carrying handles
Fan intake
Front/side view
Fog outlet
Control panel
Top view
Holder for fluid tank
Mains inlet, fuse
and power switch
Control panel
Rear/side view
DMX and remote
connectors
Product overview
7
Connections
Mains inlet panel
Main power switch
Main fuse
Power cable
DMX connections panel
DMX out/thru
(5 pin)
Digital remote
socket
DMX in plug
(5 pin)
Electronics power
LED
DMX in plug
(3 pin)
AVR socket
(service use)
Service status
LEDs
8
DMX out/thru
(3 pin)
Product overview
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot
of fog. This section tells you how to do that. However, please also make the time
to read the safety and servicing instructions in the remainder of this manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the smoke
output. Read the “Installation” section before rigging the machine from
suspension points.
Fill the fluid tank with JEM-approved fluid (see page 19).
Connect a suitably rated power supply to the machine. The machine requires
13.1A at 230V (EU) or 11.8A at 208V (US).
Turn on the Standby switch. The display will show (%!4 for about 8-12
minutes and will then change to 1$9 (Ready).
Making fog
You can then use the Timer or Continuous switches on the back of the machine
or the buttons on the remote (optional accessory) to turn on the fog output.
If no fog is produced, check that the FOG option is not set to 0% (see page 13)
and that if using Timer mode the TRUN setting is not set to 0. Also check that
the machine has fluid.
Quick Start
9
Installation and setting up
DANGER! DO NOT operate the Roadie Compact until you have read and
observed all the precautions listed under “Safety information” on page 3.
Location
The Roadie Compact may be located on the floor or may be suspended using
the rigging points.
The machine can operate in any orientation from horizontal (on its wheels) to
vertical (resting on its back firing upwards into the air). If using the machine
vertically the smoke fluid bottle must be turned round in the fluid compartment
so that the outlet remains on top.
The maximum downward tilt is 35 degrees (unless using an external fluid line)
as steeper angles may cause fluid leakage.
If the machine is to be suspended, a qualified rigger must be employed to
ensure the machine is rigged safely. Do not suspend the machine over areas
where people will be underneath.
Ensure that there is at least 100mm clearance all round the machine, 500mm
clearance round the fan intake and at least 600mm in front of the smoke output.
AC power
Before using the machine, a grounding-type (earthed) power plug that fits the
local power outlets must be obtained locally and installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• 'Attachment plugs shall be rated not less than 125% of the rated current of
the equipment'
When installing the plug, follow the plug manufacturer’s instructions and
connect pins as follows:
yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
green
Before connecting the Roadie Compact to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires 13.1A at 230V (EU) or 11.8A at 208V (US).
10
Installation and setting up
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Jem Service for assistance.
Setting up
Fill the fluid tank with JEM-approved fluid (see page 19), or connect up the fluid
line extension kit (optional accessory) if remote fluid tanks are being used.
If DMX control is being used, connect the machine to the DMX line (see page
18).
If the Jem Digital Remote is being used (optional accessory), connect the
remote to the Remote socket. (see page 18)
Final checks
Before applying power to the Roadie Compact, verify the following:
• the machine is safely located or installed and meets the location
requirements stated on page 10
•
the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 3
•
the smoke fluid is one of the genuine Jem fluids listed under “Smoke
fluid options” on page 19
•
the machine is electrically grounded (earthed)
•
the AC power distribution circuits and lines are adequately rated for the
current load
Turning on the power
Turn on the main power switch located next to the power cable inlet.
Turn on the Standby switch on the control panel.
The display will show (%!4 for about 8-12 minutes as the machine heats up
to operating temperature and will then change to 1$9 (Ready).
You can then use the control panel to make fog.
Installation and setting up
11
Control settings
Overview
1$9
Four quick access switches at the sides of the panel allow you to control the
main functions:
Standby: Enables the machine and tells it to heat up when turned on. When
turned off, disables the machine and turns off the heaters.
Fan: Turns on continuous fan mode. The Fan speed can be set using the Fan
menu option.
Timer: Turns on the Fog Timer mode. The Run and Off times for the timer can
be set using the TRUN and TOFF menu options, and are initially set to 10 secs
run, 20 secs off. The Fog density can be set using the Fog menu option.
Fog: Turns on continuous fog mode. The Fog density can be set using the Fog
menu option. This is initially set to 50%.
The digital display in the centre of the panel allows you to configure the
machine using option menus.
Digital display
1$9
Menu previous/next
buttons
Value down/up
buttons
Enter/store button
12
Control settings
Setting Fog density
Use the Menu Previous / Next buttons to select the &/' option.
Use the Up/Down buttons to select the density from – .
Press the Enter button to store the fog setting. The display shows 3%4.
The machine will only produce fog if the Timer or Continuous switches are On.
(Or, if using the digital remote, if you press the Timer or Fog buttons).
If you want to temporarily change the fog density, do not press Enter.
The fog setting will go back to its stored value next time the machine
is powered up. This applies to all options.
If a long burst of fog is produced, after a time the fog density will be
automatically reduced to keep the machine temperature within the operating
range. This allows continuous operation, so that the machine does not have to
stop and re-heat.
Setting Fan speed
Use the Previous / Next buttons to select the &!. option.
Use the Up/Down buttons to select the fan speed from – .
Press the Enter button to store the fan setting.
The fan will run continuously if set above 0% and the Fan, Timer or Continuous
switches are On. (Or, if using the digital remote, if the RUN menu is set to FAN,
TIME or CONT).
If fog is being produced and the fan is off or set to a low speed, the fan speed
will be automatically increased to prevent buildup of fog at the machine output.
Setting the Timer
If smaller amounts of fog are required the machine has an automatic timer to
give timed bursts of fog. You can set the “Run” and “Off” times independently
between 1 and 90 seconds.
Use the Previous / Next buttons to select the 415. or 4/&& option.
Use the Up/Down buttons to select the run or off time from seconds to seconds. If you hold down the button the time will count up or down, getting
faster the longer you hold it.
Press the Enter button to store the timer setting.
To enable timer mode, switch on the Timer switch (or, if using the digital remote,
press the Timer button).
When the timer is running and the display is not showing a menu, the
display shows a countdown for the run time (RU--) and the off time
(OF--).
Control settings
13
Setting the DMX base address
Use the Previous / Next buttons to select the !$$1 option.
Use the Up/Down buttons to set the DMX base address from to . If
you hold down the button the address will count up or down, getting faster the
longer you hold it.
Press the Enter button to store the address setting.
The machine will automatically respond to a DMX controller whenever it is
connected.
Setting the operating temperature
The machine provides three temperature settings which are required for different
types of JEM smoke fluid. See page 19 for details of the fluids available.
Use the Previous / Next buttons to select the 4%-2 option.
Use the Up/Down buttons to select ,/7, ./1- or ()'(.
Press the Enter button to store the temperature setting.
fluid
temperature setting
Pro Steam Simulation
,/7
Regular DJ Fluid (DJ mix)
./1-
Pro Smoke Super (ZR mix)
()'(
Pro Smoke High Density (SP mix)
()'(
Setting the control panel display brightness
Use the Previous / Next buttons to select the $)32 option.
Use the Up/Down buttons to select ,/7, ./1- or ()'(.
Press the Enter button to store the brightness setting.
This function might be useful to make the display less obtrusive if the machine is
visible to audience.
Setting the master-slave link mode
It is possible to control several machines from one digital remote. The machine
with the remote plugged into it becomes the Master. The other machines are
Slaves. The machines are interconnected with DMX cabling.
Use the Previous / Next buttons to select the ,).+ option.
Use the Up/Down buttons to select 1%#6 or 3%.$.
Press the Enter button to store the link setting.
The machine should be set to 3%.$ only if it is running as a master. If running
as a slave, stand-alone or DMX controlled it should be set to 1%#6.
Aux option
This option is not currently used and has no effect on the machine.
14
Control settings
Priming the machine after fluid out
If the machine runs out of fluid it will display &,5/54 and shut down to
prevent damage to the pumps. To suck the new fluid back into the machine and
reset the fluid out error, refill the fluid and use the prime function.
Use the Previous / Next buttons to select the 21-% option.
Use the Up/Down buttons to change the option to 9.
Press the Enter button to start the priming function.
The machine will pump at full power for about 7 seconds. You may need to use
the function several times to get both nozzles running properly.
To exit this menu if you decide not to activate the Prime function, select . and
press Enter.
If the machine is not up to operating temperature the Prime function will do
nothing.
Resetting options to factory settings
The factory settings configure a standard mode of operation for the machine.
Use the Previous / Next buttons to select the 13%4 option.
Use the Up/Down buttons to change the option to 9.
Press the Enter button to reset all options.
To exit this menu if you decide not to reset the options, select . and press
Enter.
The factory settings are:
option
setting
FOG
FAN
TRUN
TOFF
RUN
/&&
TEMP
./1-
DISP
()'(
LINK
1%#6
Control settings
15
Remote control
Overview
The Jem digital remote control, available separately, may be used for remote
control of the Roadie Compact. Several machines may be controlled from one
remote using the LINK function (see page 14).
Display
XLR socket
XLR socket
(on rear)
Timer button
Fog button
Functions
The remote control provides the following functions:
•
Fog button: turns fog output on and off. Press once to start fog and
again to stop.
•
Timer button: turns the fog timer on and off.
•
Fog level setting (FOG = 0 -100%)
•
Fan speed setting (FAN = 0 -100%)
•
Timer run time/off time settings (TRUN, TOFF = 0 - 90 seconds)
•
Run mode (RUN = OFF, STBY, FAN, TIME, CONT)
•
Head temperature setting (TEMP = LOW, NORM, HIGH)
The functions are the same as on the built in control panel and are described on
page 13.
The RUN menu duplicates the functions of the Standby, Fan, Timer and
Continuous Fog quick-access switches on the rear of the machine. The Fog and
Timer buttons on the remote are simply a quick way to control this menu
function.
16
Remote control
Connection
The remote control has two identical XLR sockets on the top and back for
connection to the Roadie Compact. Plug the cable provided with the remote
control into one of these sockets and into the XLR socket labelled REMOTE on
the rear panel of the Roadie Compact.
The remote control is powered through its cable by the Roadie Compact; no
batteries are required.
The cable may be extended to up to 25 m (82 ft.) with a 3-pin XLR DMX cable,
available from your Jem dealer.
Remote control
17
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512 standard may be used to control
and program the fog output of the Roadie Compact.
When a DMX signal is present, the Roadie Compact’s stand-alone
functions do not work. To fire the unit from the control panel or remote
control, the DMX controller must be powered off or disconnected.
Connection
The Roadie Compact provides both 3-pin and 5-pin XLR sockets on the rear
panel of the base for DMX connection. The sockets are interconnected: a DMX
line connected to the 3-pin IN socket may be continued through the 5-pin OUT
socket and vice versa. Do not, however, attempt to split a DMX line by using
both the 3-pin and 5-pin OUT sockets.
For best results, use cable designed for high speed digital data transmission.
Suitable DMX cable is available from your Jem dealer.
DMX functions
The Roadie Compact’s address setting must match the DMX address allocated
to it on the controller. To set the address, see “Setting the DMX base address”
on page 14. The Roadie Compact requires two DMX channels.
DMX channel
function
1
Fog density 0-100%
2
Fan speed 0-100% and Shutdown
Channel 1 uses the full range 0-255 for fog density control.
Channel 2 has the following control values.
DMX value
function
0-244
Fan speed 0-100%, heaters on
245-255
machine shutdown, heaters off
For example if the Roadie Compact is set to DMX address 100, channel 1 will be
controlled by address 100 and channel 2 will be controlled by address 101.
When the machine is at running temperature and is under DMX control it
displays $-8.
18
DMX control
Fog fluid types
The following types of Jem fog fluid are suitable for use in this machine. Each
produces a different effect as described below. Jem supplies high quality fog
fluids that are based on ultra-pure deionized water. Use only the following
genuine Jem fog fluids. No other fluid is suitable for use.
DANGER! The Roadie Compact can run safely only on the specific smoke fluids
it is designed for. Use ONLY the Jem smoke fluids designated in this manual.
NEVER use any other type of fluid, or toxic gas may be produced. You will
probably also cause damage to the system that is not covered by the
product warranty. Do not dilute smoke fluid with water or any other liquid. Discard
smoke fluid if it becomes contaminated.
Ensure the operating temperature is set to the correct option for the fluid type.
See page 14.
Pro Steam Simulation
Pro Steam Simulation fluid is a light fluid that produces well-defined cones of
steam that disperse quickly. It is ideal for chase effects and theatrical use. When
using Pro Steam Simulation fluid, the operating temperature must be set to
,/7.
Regular DJ Fluid (DJ mix)
Regular DJ fluid is an economical fluid that gives a good, medium density
smoke well-suited for atmospheric effects. When using DJ mix, the operating
temperature must be set to ./1-.
Pro Smoke Super (ZR mix)
Pro Smoke Super fluid is a high-quality, general purpose fluid that produces a
dense white airborne fog with medium dispersal time. Its medium to high index
of refraction permits both good atmospheric effects and denser “white-outs”.
When using ZR mix, the operating temperature must be set to ()'(.
Pro Smoke High Density (SP mix)
Pro Smoke High Density fluid generates a high density, white, airborne fog with
a very high index of refraction and slow evaporation rate. It is well suited for
scenic obscuring, dramatic strobe effects, and “white-outs”. When using SP mix,
the operating temperature must be set to ()'(.
Fog fluid types
19
Basic service
Before servicing the Roadie Compact, read and observe all the precautions listed
in “Safety information” on page 3. Any service not described in this section must
be carried out by a Jem service technician.
Cleaning
Excessive dust, smoke fluid, and dirt buildup will degrade performance and
cause overheating and damage to the machine that is not covered by the
product warranty. To maintain adequate cooling, dust must be cleaned from the
outer casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The smoke output nozzle remains hot for up to 10 hours after use.
•
Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
•
Clean smoke fluid residues from the fog output of the machine.
•
Clean the outer casing with a damp cloth only.
Fuse replacement
The main fuse for the Roadie Compact is in a fuse holder located adjacent to the
power inlet. To replace the fuse, disconnect the power cord from the supply,
unscrew the cap of the fuse holder and pull out the fuse. Remove the spent fuse
and replace with one of exactly the same size and rating. The fuse type is
indicated on the serial number label. Contact Jem Service if the fuse blows
repeatedly.
If the machine partially runs but some features do not operate, one of the
internal fuses may have blown. These fuses are located on the power pcb which
may be accessed by removing the power inlet panel.
DANGER! Isolate the machine from power before removing any panels. Live
electrical parts inside.
One output not operating: Check heater fuses FS1/FS2
Heating but not pumping / fan not working: Check FS3
Mains in OK but electronics power LED not lit: Check FS4.
Contact Jem Service if the problem persists.
20
Basic service
Troubleshooting
Problem
Probable cause(s)
Suggested remedy
Machine not at operating
temperature
Wait 10 to 15 minutes
&/' set to 0
Increase setting
415. set to 0
Increase setting
DMX signal present
Disconnect or turn off DMX
controller
Fog is only produced from
one output nozzle
One output has heated
faster, the other is not ready
yet
Wait a few more minutes for
the other output to heat
“Flu out” message
displayed, but there is fluid
in the tank
Machine requires priming
Prime machine (page 15)
Machine can be fired from
control panel or remote
control, but not by DMX
controller
DMX address setting
incorrect
Change DMX address (page
14)
Poor connection in DMX line
Check DMX cables and
connections
Smoke output is weak
Machine requires priming
Prime machine (page 15)
Wet, greasy, non-uniform
smoke output, fluid drips or
spits from nozzles, or very
loud noise when firing
machine
Incompatible smoke fluid
Use approved fluid!
Incorrect operating
temperature
Refer to “Setting the
operating temperature” on
page 14
Mains fuse blown
Replace fuse (page 20)
No power at AC cable inlet
Check power cable and
circuit breaker
Machine will not produce fog
when control panel or
remote control Fog switch
turned on
Machine appears dead
Troubleshooting
21
Status messages
message
/&&
(%!4
reason
The heaters are Off, the unit is shut down.
The unit is heating up to operating temperature.
One or both of the heaters are at operating temperature, but
1$9
Fog is not turned on.
One or both of the heaters are at operating temperature and
$-8
the unit is under DMX control.
One or both of the heaters is at too high a temperature. This
/6%1
indicates a fault. Turn the machine off and call Jem Service.
The machine has detected that it has run out of fluid. Refill
&,5/54 the fluid container and use the Prime function to prime the
machine and reset the fluid out error.
(number may be 01 to 90): Machine is in timer mode,
1.
counting down the run period.
(number may be 01 to 90): Machine is in timer mode,
/&
counting down the off period.
The machine has detected an error with its calibration
#!,%11
settings and will not operate. Call Jem Service.
The machine has detected an error in the temperature
4%-2%11
sensors and will not operate. Call Jem Service.
22
Status messages
Specifications
P h ys i c a l
Length .......................................................................................................... 844mm
Width ............................................................................................................ 580mm
Height........................................................................................................... 592mm
Dry weight .........................................................................................................80kg
Performance
Air volume of effect ..............................................................................1490m3/hour
Exit velocity ......................................................................... 12.7m/sec (2500ft/min)
Operating time ....................................................................................... Continuous
Warm-up time........................................................ 9 minutes (EU)/12 minutes (US)
Control and programming
Control options .................DMX, stand-alone, Jem Remote Control (not included)
DMX channels .........................................................................................................2
F l u i d s ys t e m
Fluid pumps ................................................................................................... 16 bar
Fluid capacity .............................................................................................. 9.5 litres
Maximum fluid consumption at peak output ............................... 220ml per minute
Installation
Orientation............................................................................... Horizontal or vertical
Connections
DMX................................................................................................. 3 and 5 pin XLR
Remote control.......................................................................................... 3 pin XLR
AC power ................................................................................ Captive power cable
Electrical
AC power (auto voltage/frequency adjust) ................................ 208-250V, 50/60Hz
Main fuse.......................................................................................15AT (slow-blow)
Power and current
Maximum at 230V 50Hz ........................................................................ 3000W, 13A
Maximum at 208V 60Hz ..................................................................... 2450W, 11.8A
Thermal
Maximum ambient temperature (Ta max)............................................ 40°C (104°F)
Specifications
23
Exterior surface temperature, steady state .......................................... 40°C (104°F)
Approvals
European EMC:......................................................... EN 61000-6-3:2001 – Part 6-3
European safety: ......................................................................... EN 60 335-1:2002
Immunity: ................................................................... EN 61000-6-1:2001 – Part6-1
Included items
1 x 9.5 litre fluid container (empty)
Accessories
Roadie Compact remote control........................................................P/N 92765031
Roadie Compact ducting kit ..............................................................P/N 92625010
Ordering information
Jem Roadie Compact 208V-230V 50/60Hz .......................................P/N 92230500
24
Specifications