Insignia NS-SB314 Home Theater System User Manual

DTR-5.9_En.book Page 1 Tuesday, April 15, 2008 9:53 AM

AV Receiver

DTR-5.9

Instruction Manual


Thank you for purchasing an Integra AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver.

Please retain this manual for future reference.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

PORTABLE CART WARNING

S3125A

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged,

B. If liquid has been spilled, or objects have fallen into the apparatus,

C. If the apparatus has been exposed to rain or water,

D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in any way, and

F. When the apparatus exhibits a distinct change in performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of this unit.

17. Batteries

Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation.

Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.


Precautions

1. Recording Copyright

—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse

—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer.

3. Care

—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SEC-

TION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel

(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Pressing the [On/Standby] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Never Touch this Unit with Wet Hands

—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by the dealer.

6. Handling Notes

• If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after prolonged use. This is normal.

• If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE:

THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION:

TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

Pour les Modèles Canadiens

REMARQUE:

CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME

NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION:

POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE CORRE-

SPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

3


4

Supplied Accessories

Make sure you have the following accessories:

Remote controller and two batteries (AA/R6)

Speaker setup microphone

Indoor FM antenna

AM loop antenna

Power cord

(Power cord varies from country to country.)

Speaker Cable

1

2

3

Speaker cable labels

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color.

Contents

Important Safety Instructions...........................2

Supplied Accessories ......................................4

Features .............................................................6

Multiroom Capability ........................................7

Getting to Know the AV Receiver ....................8

Front Panel .............................................................. 8

Display .................................................................... 9

Rear Panel ............................................................. 10

Remote Controller ..........................................12

Controlling the AV Receiver ................................ 12

Installing the Batteries .......................................... 13

Using the Remote Controller ................................ 13

Connecting Your Speakers ............................14

Enjoying Home Theater ....................................... 14

Bi-amping Front Speakers .................................... 18

Connecting Antennas .....................................19

Connecting the Indoor FM Antenna ..................... 19

Connecting the AM Loop Antenna ...................... 19

Connecting an Outdoor FM Antenna ................... 20

Connecting an Outdoor AM Antenna ................... 20

Connecting Your Components ......................21

About AV Connections ........................................ 21

Connecting Audio and Video Signals to the AV Receiver ............................................. 22

Which Connections Should I Use? ....................... 22

Connecting a TV or Projector ............................... 24

Connecting a DVD player .................................... 25

Connecting a VCR or DVR for Playback ............. 27

Connecting a VCR or DVR for Recording ........... 28

Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source ............................... 29

Connecting a Game Console ................................ 30

Connecting Components with HDMI ................... 31

Making HDMI Connections ................................. 32

Connecting a Camcorder or Other Device ........... 33

Connecting a Power Amplifier ............................. 33

Connecting a CD Player or Turntable .................. 34

Connecting a Cassette, CDR, MiniDisc, or

DAT Recorder .................................................... 35

Connecting an RI Dock ........................................ 36

Connecting Integra/Onkyo Components ....... 37

Turning On the AV Receiver ..........................38

Connecting the Power Cord .................................. 38

Turning On and Standby ...................................... 38

First Time Setup ..............................................39

Automatic Speaker Setup ..................................... 39

Speaker Settings ................................................... 43

HDMI Input Setup ................................................ 44

Component Video Input Setup ............................. 45

Digital Input Setup ............................................... 45

Changing the Input Display .................................. 46

Automatic Audio Input Selection Setup ............... 47


Contents

—Continued

Playing Your AV Components ...................... 48

Basic AV Receiver Operation ...............................48

Common Functions ........................................ 49

Setting the Display Brightness ..............................49

Muting the AV Receiver .......................................49

Using the Sleep Timer ...........................................49

Using Headphones ................................................50

Displaying Source Information .............................50

Specifying the Digital Signal Format ....................51

Listening to the Radio .................................... 52

AM Frequency Step Setup

(on some models) ................................................52

Listening to AM/FM Stations ...............................53

Presetting AM/FM Stations ...................................55

Listening to SIRIUS Satellite Radio®

(North American Models Only) ..........................56

Using RDS (European models only) .....................65

Using the Listening Modes ............................ 67

Selecting the Listening Modes ..............................67

Listening Modes Available for Each Source

Format .................................................................68

About the Listening Modes ...................................74

Recording ........................................................ 76

Recording the Input Source ...................................76

Recording from Different AV Sources .................76

Adjusting the Listening Modes ..................... 77

Using the Audio Adjust Settings ...........................77

Using the Audio Settings ......................................79

Listening Mode Presets .........................................81

Advanced Setup ............................................. 82

Speaker Setup ........................................................82

Source Setup ..........................................................87

Miscellaneous Setup ..............................................88

Hardware Setup .....................................................89

Lock Setup ............................................................92

Zone 2 .............................................................. 93

Connecting Zone 2 ................................................93

Powered Zone 2 Setting ........................................94

Zone 2 Out Settings ...............................................95

Using Zone 2 .........................................................96

Using the 12V Triggers .........................................98

Using the Remote Controller in Zone 2 and

Multiroom Control Kits ......................................99

Controlling Other Components ................... 100

Preprogrammed Remote Control Codes .............100

Entering Remote Control Codes .........................100

Resetting the Remote Controller .........................101

Controlling a TV .................................................102

Controlling a DVD Player, or DVD Recorder ....103

Controlling a VCR or DVR .................................104

Controlling a Satellite Receiver or Cable

Receiver ............................................................105

Controlling a CD Player, CD Recorder, or MD Player .................................................... 106

Controlling an RI Dock ...................................... 107

Controlling a Cassette Recorder ......................... 108

Troubleshooting ...........................................109

Specifications ...............................................113

Video Resolution Chart ................................114

Onscreen Setup Menus ................................115

* To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] but-

ton, press the [On/Standby] button (see page 109).

5


Features

Amplifier

• 7-channel amplifier

• 90 Watts/Channel @ 8 ohms (FTC)

• WRAT-Wide Range Amplifier Technology

(5Hz–100kHz bandwidth)

• Optimum Gain Volume Circuitry

Processing

• HDMI Video Upscaling (Up to 1080i)

• HDMI Video Upconversion

• Dolby TrueHD

*1

• DTS-HD Master Audio

*2

• Faroudja DCDi Edge Enhancement

• Direct Mode

• Music Optimizer

*3

for Compressed Music

• CinemaFILTER

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• 24-bit/192kHz D/A Converters

• Powerful and Highly Accurate 32-bit DSP Processing

Connections

• 4 HDMI

*4

Inputs and 1 Output

• Integra RIHD for System Control

• HDTV-Ready Component Video Switching

(2 Inputs/1 Output)

• 4 Digital Inputs (2 Optical/2 Coaxial/4 Assignable),

1 Digital Output (Optical)

• 4 S-Video Inputs/2 Outputs

• Powered Zone 2

• Color-Coded 7.1 Multichannel Inputs

• Bi-Amp Connectable for Front L/R with Surround

Back L/R

Miscellaneous

• 40 Sirius

*5

/AM/FM Presets (North American model)

• 40 AM/FM Presets (Other models)

• Audyssey 2EQ

*6

Room Correction and Speaker Calibration

• Audyssey Dynamic EQ

*6

Loudness Correction

• Crossover Adjustment

(40/45/50/55/60/70/80/90/100/110/120/130/150/

200Hz)

• A/V Sync Control Function (up to 100 ms)

• On-Screen Display

• Compatible with RI Dock for iPod

• Aluminum Front Panel

*1.

*2.

Manufactured under license from Dolby Laboratories. Dolby,

Pro Logic, and the double-D symbol are trademarks of Dolby

Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and

DTS-HD Master Audio are trademarks of DTS, Inc.

“DTS” and “DTS-ES | Neo: 6” are registered trademarks of

DTS, Inc. “96/24” is a trademark of DTS, Inc.

*3 Music Optimizer™ is a trademark of Onkyo Corporation.

*4

HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

*5

©2005 SIRIUS Satellite Radio Inc. “SIRIUS,” SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Available only in the contiguous

United States (excluding Alaska and Hawaii) and Canada.

*6

Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey 2EQ and Dynamic EQ are trademarks of Audyssey Laboratories.

* Apple and iPod are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

* “x.v.Color” is a trademark of Sony Corporation.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

6


Multiroom Capability

You can use two speaker systems with this AV receiver

—a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it. And, you can select a different audio source for each room.

Main Room:

In your main listening room, you can enjoy up to 7.1-channel playback (see page 14).

You can enjoy the various listening modes such as Dolby and DTS (pages 67–75).

*While Powered Zone 2 is being used, playback is reduced to 5.1-channels (see page 93).

Zone 2:

In your Zone 2 room, you can enjoy 2-channel stereo playback (see page 93).

*The listening modes cannot be used with Zone 2.

Front left and right speakers

Main Room

Surround back left and right speakers

* While Powered Zone 2 is being used, nothing is output by these

speakers (page 94).

Subwoofer

Center speaker

Zone 2 Room

Left and right stereo speakers

Surround left and right speakers

7


Getting to Know the AV Receiver

Front Panel

North American model

1 2 3 4 5 6 7 8 9 J K L M N O

P Q

Other models

R S T U V

8

9

The actual front panel has various logos printed on it. They are not shown here for clarity.

The page numbers in parentheses show where you can find the main explanation for each item.

A

B

On/Standby button (38)

Sets the AV receiver to On or Standby.

Standby indicator (38)

Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller.

C

Zone 2 indicator (96)

Flashes when Zone 2 is being set. Lights up when

Zone 2 is on.

D

Remote-control sensor (13)

Receives control signals from the remote controller.

E

Movie/TV button (67)

Selects the listening modes intended for use with movies and TV.

F

Music button (67)

Selects the listening modes intended for use with music.

G

Game button (67)

Selects the listening modes intended for use with video games.

H

Display

See “Display” on page 9.

I

Dimmer (RT/PTY/TP) button (49, 66)

Adjusts the display brightness.

On the European models, this is the RT/PTY/TP button, and it’s used with RDS (Radio Data Sys-

tem). See “Using RDS (European models only)” on page 65.



—Continued

J

Memory button (55)

Used when storing or deleting radio presets.

K

Tuning Mode button (53)

Selects the Auto or Manual tuning mode for AM and FM radio.

L

Display button (50)

Displays various information about the currently selected input source.

M

Setup button

Opens and closes the onscreen setup menus, which are displayed on the connected TV.

N

Tuning, Preset, Arrow, and Enter buttons

When AM or FM is selected, the Tuning [ ] [ ] buttons are used for radio tuning, and the Preset

[ ] [ ] buttons are used to select radio presets

(see page 55). With the onscreen setup menus, they

work as arrow buttons and are used to select and set items. The Enter button is also used with the onscreen setup menus.

O

Master Volume control (48)

Sets the volume of the AV receiver to Min, 1 through, or Max.

The maximum volume level can be limited with the

Maximum Volume setting. See “Volume Setup” on page 88.

P

Zone 2, Level [ ]/[

], and Off buttons (96)

The Zone 2 button is used when setting Zone 2.

The Level Up and Down [ ]/[ ] buttons are used when adjusting the volume level of Zone 2.

The Off button is used to turn off Zone 2.

Q

Phones jack (50)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

R

Input selector buttons (48)

Select the following input sources: DVD,

VCR/DVR, CBL/SAT, Game/TV, AUX, Tape,

Tuner, CD.

The [Multi CH] button selects the multichannel

DVD input.

S

Tone, Plus [+], and Minus [–] buttons (79, 97)

Used to adjust the tone (bass and treble), and the volume and balance of Zone 2.

T

Setup Mic (39)

The automatic speaker setup microphone connects here.

U

Return button

Selects the previously displayed setup menu.

V

AUX Input (33, 76)

Used to connect a camcorder, game console, and so on. There are input jacks for composite video and analog audio.

Display

1 2 3 4

5 6

For detailed information, see the pages in parentheses.

1

SLEEP indicator (49)

Lights up when the Sleep function has been set.

2

MUTING indicator (49)

Flashes while the AV receiver is muted.

3

Listening mode and format indicators (51,

67)

Show the selected listening mode and audio input signal format.

4

Tuning indicators (53)

FM STEREO (53):

Lights up when tuned to a stereo FM station.

RDS (65):

Lights up when tuned to a radio station that supports RDS (Radio Data System).

7

AUTO (53):

Lights up when Auto Tuning mode is selected for AM or FM radio. Goes off when Manual Tuning mode is selected.

TUNED (53):

Lights up when tuned to a radio station.

5

Message area

Displays various information.

6

Audio input indicators

Indicate the type of audio input that’s selected as the audio source: MULTI CH, or HDMI.

7

Audyssey indicator

Flashes during automatic speaker setup.

9



—Continued

Rear Panel

North American model

1 2 3 4 5 6

7

Only North American model

8 9 J K L M N

SIRIUS

AM

ANTENNA

FM

75

O P Q R S T U V W

Other models

1 2 3 4 5 6 8 9

X

J K

Y

L M N

Z

AM

ANTENNA

FM

75

O P Q R S T U V W

10

A

DIGITAL IN COAXIAL 1 and 2

These coaxial digital audio inputs are for connecting components with a coaxial digital audio output, such as a CD player or DVD player. They’re assignable, which means you can assign each one to an

input selector to suit your setup. See “Digital Input

Setup” on page 45.

B

COMPONENT VIDEO IN 1 and 2

These RCA component video inputs are for connecting components with a component video output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector

to suit your setup. See “Component Video Input


X Y Z

C

COMPONENT VIDEO OUT

This RCA component video output is for connecting a TV or projector with a component video input.

D

HDMI IN 1–4 and OUT

HDMI (High Definition Multimedia Interface) connections carry digital audio and digital video.

The HDMI inputs are for connecting components with an HDMI output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to

an input selector to suit your setup. See “HDMI

Input Setup” on page 44.

The HDMI outputs are for connecting a TV or projector with an HDMI input.



—Continued

E

ETHERNET

This port is for connecting the AV receiver to home automation equipment and external controllers. Use only shielded Ethernet cables.

F

MONITOR OUT

The S-Video or composite video jack should be connected to a video input on your TV or projector.

G

SIRIUS antenna (on North American model)

This jack is for connecting a SIRIUS digital antenna, sold separately (see the separate SIRIUS instructions).

H

FM ANTENNA

This jack is for connecting an FM antenna.

I

AM ANTENNA

These push terminals are for connecting an AM antenna.

J

IR IN A/B and OUT

A commercially available IR receiver can be connected to the IR IN A or B jack, allowing you to control the AV receiver while you’re in Zone 2, or control it when it’s out of sight, for example, installed in a cabinet.

A commercially available IR emitter can be connected to the IR OUT jack to pass IR (infrared) remote control signals through to other components.

K

12V TRIGGER OUT (A/B/C)

These outputs can be connected to the 12-volt trigger inputs on other components.

L

RS232

This port is for connecting the AV receiver to home automation equipment and external controllers.

M

ZONE 2 PRE OUT L/R

These analog audio outputs can be connected to the line inputs on amplifiers in Zone 2.

N

ZONE 2 SPEAKERS L/R

These terminal posts are for connecting speakers in

Zone 2.

O

DIGITAL OPTICAL IN 1, 2, and OUT

These optical digital audio inputs are for connecting components with an optical digital audio output, such as a CD player or DVD player. They’re assignable, which means you can assign each one to an

input selector to suit your setup. See “Digital Input


The optical digital audio output is for connecting a digital recorder with an optical digital input, such as a CD recorder.

P

REMOTE CONTROL

This (Remote Interactive) jack can be connected to the jack on another -capable Integra/

Onkyo component for remote and system control.

To use , you must make an analog audio connection (RCA) between the AV receiver and the other component, even if they are connected digitally.

Q

CD IN

This analog audio input is for connecting a CD player’s analog audio output.

R

TAPE IN/OUT

These analog audio input and output jacks are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc.

S

GAME/TV IN

A game console or TV output can be connected here. There’s S-Video and composite video input jacks for connecting the video signal.

T

CBL/SAT IN

A cable or satellite receiver can be connected here.

There are S-Video and composite video input jacks for connecting the video signal, and there are analog audio input jacks for connecting the audio signal.

U

VCR/DVR IN/OUT

A video component, such as a VCR or DVR, can be connected here for recording and playback. There are S-Video and composite video input and output jacks for connecting the video signal, and there are analog audio input jacks for connecting the audio signal.

V

DVD IN

This input is for connecting a DVD player. There are S-Video and composite video input jacks for connecting the video signal.

W

DVD FRONT L/R, CENTER, SUBWOOFER,

SURR L/R, and SURR BACK L/R

This analog multichannel input is for connecting a component with a 5.1/7.1-channel analog audio output, such as a DVD player, DVD-Audio or

SACD-capable player, or an MPEG decoder.

X

PRE OUT: FRONT L/R, CENTER, SUB-

WOOFER, SURR L/R, and SURR BACK L/R

This 5.1/7.1 multichannel analog audio output can be connected to the analog audio input on a multichannel power amplifier for when you want to use the AV receiver solely as a preamplifier. The SUB-

WOOFER jack is for connecting a powered subwoofer.

Y

FRONT L/R, CENTER, SURR L/R, and SURR

BACK L/R SPEAKERS

These terminal posts are for connecting the front speakers, center, surround, and surround back speakers.

Z

AC INLET

The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.

See pages 14–37 for hookup information.

11


12

Remote Controller

Controlling the AV Receiver

To control the AV receiver, press the [Receiver]

Remote Mode button to select Receiver mode.

You can also use the remote controller to control your DVD player, CD player, and other components.

See page 100 for more details.

A

2

3

Receiver

1 4

3

5

6

2

7

*

8

9

J

5

4

Tuner

K

L

M

For detailed information, see the pages in parentheses.

A

On/Standby button (38)

Sets the AV receiver to On or Standby.

B

Remote Mode/Input Selector buttons (48,

102–108)

Selects the remote controller modes and the input sources.

C

Multi CH button (48)

Selects the multichannel DVD input.

D

Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons

Used to select and adjust settings.

E

Setup button

Used to change settings.

F

Listening Mode buttons (67)

Used to select the listening modes.

G

Dimmer button (49)

Adjusts the display brightness.

H


Displays information about the current input source.

I

Muting button (49)

Mutes or unmutes the AV receiver.

J

VOL [ ]/[

] button (48)

Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode.

K

Return button

Returns to the previous display when changing settings.

L

Audio button (79)

Used to change audio settings.

When the Audio TV Out setting is set to On

(page 91), this button is disabled.

M

Sleep button (49)

Used with the Sleep function.

* SP A/B is not used in this AV receiver.

■

Controlling the tuner

To control the AV receiver’s tuner, press the [Tuner] (or

[Receiver]) Remote Mode button.

You can select AM or FM by pressing the [Tuner] button repeatedly.

1

Arrow [ ]/[ ] buttons

Used to tune into radio stations.

2

Number buttons (54)

Used to select AM and FM radio stations directly.

3

D.TUN button (54)

Selects the Direct tuning mode.

4


Displays information about the band, frequency, preset number, and so on.

5

CH +/– button (55)

Selects radio presets.

Note:

• An Onkyo cassette recorder connected via can

also be controlled in Receiver mode (see page 108).



—Continued

Installing the Batteries

1

To open the battery compartment, press the small lever and remove the cover.

Using the Remote Controller

When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.

Remote control sensor

Standby indicator

AV receiver

2

3

Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment.

Replace the cover and push it shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

30˚

30˚

Approx. 16 ft.

(5 m)

Notes:

• The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.

• The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.

13


Connecting Your Speakers

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS.

With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.

Front left and right speakers

These output the main sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.

Surround left and right speakers

These speakers are used for precise sound positioning and to add realistic ambience.

Position them at the sides of the listener, or slightly behind, about 2–3 feet

(60–100 cm) above ear level. Ideally they should be equally spaced from the listener.

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies it’s used mainly for dialog.

Position it close to your TV (preferably on top) facing forward at about ear level, or at the same height as the front left and right speakers.

14

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel.

The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the front wall, as shown.

Tip: To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room and choose the one that provides the most satisfying results.

Surround back left and right speakers

These speakers are necessary to enjoy Dolby Digital

EX, DTS-ES Matrix, DTS-ES Discrete, etc. They enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2–3 feet (60–100 cm) above ear level.

Corner position

1/3 of wall position



—Continued

Speaker Configuration

For 7.1-channel surround-sound playback, you need seven speakers and a powered subwoofer.

The following table shows which channels you should use based on the number of speakers you have.

Number of speakers: 2 3 4 5 6 7

Front left

Front right

Center

Surround left

Surround right

Surround back*

Surround back left

Surround back right

✓ ✓ ✓ ✓ ✓ ✓

✓ ✓ ✓ ✓ ✓ ✓

✓ ✓ ✓ ✓

✓ ✓ ✓ ✓

✓ ✓ ✓ ✓

✓

✓

✓

* If you’re using only one surround back speaker, connect it to the

SURR BACK L terminals.

No matter how many speakers you use, a powered subwoofer is recommended for a powerful and solid bass.

To get the best from your surround-sound system, you must set the speaker settings. You can do this automati-

cally (see page 39) or manually (see page 82).

Using Dipole Speakers

You can use dipole speakers for the surround left and right and surround back left and right speakers. Dipole speakers output the same sound in two directions.

Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround left and right dipole speakers should be positioned so that their arrows point toward your TV or screen, while the surround back left and right dipolar speakers should be positioned so that their arrows point toward each other, as shown.

2

Dipole speakers

TV/screen

3 4

1

Normal speakers

2

TV/screen

3

4

1

5 6 5

7 8

1. Subwoofer

2. Front left speaker

3. Center speaker

4. Front right speaker

5. Surround left speaker

7 8

6. Surround right speaker

7. Surround back left speaker

8. Surround back right speaker

6

15



—Continued

Speaker Connection Precautions

Read the following before connecting your speakers:

•

North American models:

You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

•

Other models:

You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum

speaker impedance to “4 ohms” (see page 43). If you

use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. Connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the

AV receiver.

• Don’t connect a speaker to several terminals.

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s PRE

OUT: SUBWOOFER to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the PRE OUT: SUB-

WOOFER to the amp’s input.

Powered subwoofer

LINE INPUT

LINE INPUT

SIRIUS

AM

ANTENNA

FM

75

SUBWOOFER

PRE OUT

Attaching the Speaker Labels

The AV receiver’s positive (+) speaker terminals are all red. (The negative (–) speaker terminals are all black.)

Speaker

Front left

Front right

Center

Surround left

Surround right

Surround back left

Surround back right

Color

White

Red

Green

Blue

Gray

Brown

Tan

The supplied speaker labels are color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal.

16



—Continued

Connecting the Speaker Cables

1

Strip about 5/8" (15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

2

Unscrew the terminal.

5/8" (15 mm)

3

Fully insert the bare wire.

4

Screw the terminal tight.

The following illustration shows which speaker should be connected to each pair of terminals.

If you’re using only one surround back speaker, connect it to the left (L) SURR BACK SPEAKERS terminals.

Surround back left speaker

Surround back right speaker

Surround left speaker

Surround right speaker

SIRIUS

AM

ANTENNA

FM

75

Front right speaker

Front left speaker

Center speaker

17



—Continued

Bi-amping Front Speakers

The FRONT L/R and SURR BACK L/R terminal posts can be used with front speakers and surround back speakers respectively, or bi-amped to provide separate tweeter and woofer feeds for front speakers, providing improved bass and treble performance.

• When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

• For bi-amping, the FRONT L/R terminal posts connect to the front speakers’ tweeter terminals. And the

SURR BACK L/R terminal posts connect to the front speakers’ woofer terminals.

• Once you’ve completed the bi-amping connections shown below and turned on the AV receiver, you must set the Speaker Type setting to Bi-Amp to enable bi-

amping (see page 43).

Important:

• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low) terminals.

• Bi-amping can only be used with speakers that support bi-amping. Refer to your speaker manual.

Bi-amping Speaker Hookup

1

Connect the AV receiver’s FRONT R positive (+) terminal to the right speaker’s positive (+) tweeter

(high) terminal. And connect the AV receiver’s

FRONT R negative (–) terminal to the right speaker’s negative (–) tweeter (high) terminal.

2

Connect the AV receiver’s SURR BACK R positive (+) terminal to the right speaker’s positive (+) woofer (low) terminal. And connect the AV receiver’s SURR BACK R negative (–) terminal to the right speaker’s negative (–) woofer (low) terminal.

3

Connect the AV receiver’s FRONT L positive (+) terminal to the left speaker’s positive (+) tweeter

(high) terminal. And connect the AV receiver’s

FRONT L negative (–) terminal to the left speaker’s negative (–) tweeter (high) terminal.

4

Connect the AV receiver’s SURR BACK L positive (+) terminal to the left speaker’s positive (+) woofer (low) terminal. And connect the AV receiver’s SURR BACK L negative (–) terminal to the left speaker’s negative (–) woofer (low) terminal.

SIRIUS

AM

ANTENNA

FM

75

R

SURR BACK SPEAKERS

Bi-AMP for FRONT SPEAKERS

L

Left speaker

Right speaker

Woofer (low)

Tweeter (high)

Woofer (low)

Tweeter (high)

FRONT SPEAKERS

L

R

18


Connecting Antennas

This section explains how to connect the supplied indoor

FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals

AM

ANTENNA

FM

75

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

1

Assemble the AM loop antenna, inserting the tabs into the base, as shown.

FM antenna jack

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

1

Attach the FM antenna, as shown.

■

American Model

2

Connect both wires of the AM loop antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around).

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

FM

75

Insert the plug fully into the jack.

■

Other Models

Release

FM

75

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

2

Use thumbtacks or something similar to fix the FM antenna into position.

AM

ANTENNA

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer-

cially available outdoor AM antenna (see page 20).

Thumbtacks, etc.

Caution:

Be careful that you don’t injure yourself when using thumbtacks.

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out-

door FM antenna instead (see page 20).

19


Connecting Antennas

—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied

AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

FM

75

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

■

Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

AM

ANTENNA

Outdoor AM antennas work best when installed horizontally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

TV/FM antenna splitter

To AV receiver To TV (or VCR)

20


Connecting Your Components

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Optical Digital Jacks

The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution:

To prevent shutter damage, hold the optical plug straight when inserting and removing.

AV Connection Color Coding

RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”).

Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

Analog audio

Left (white)

Right (red)

Left (white)

Right (red)

(Yellow)

Composite video

(Yellow)

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

Right!

Wrong!

AV Cables and Jacks

Audio/Video

Cable

HDMI

Jack

HDMI

Description

HDMI connections can carry uncompressed standard- or high-definition digital video and audio and offer the best picture and sound quality.

Video

Component video cable

S-Video cable

Y

P

B

P

R

Y

P

B

P

R

Y

CB/PB

CR/PR

S

V

Component video separates the luminance (Y) and color difference signals (P

R

, P

B

), providing the best picture quality. (Some TV manufacturers label their component video jacks slightly differently.)

S-Video separates the luminance and color signals and provides better picture quality than composite video.

Composite video is commonly used on TVs, VCRs, and other video equipment.

Composite video cable

Audio

Optical digital audio cable

Coaxial digital audio cable

Analog audio cable (RCA)

Multichannel analog audio cable (RCA)

L

R

OPTICAL

COAXIAL

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial.

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical.

This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components.

This cable carries multichannel analog audio and is typically used to connect DVD players with a 7.1channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.

Note:

The AV receiver does not support SCART connections.

21



—Continued

Connecting Audio and Video Signals to the AV Receiver

By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.

: Signal Flow

Video

Video

Audio Audio

TV, projector, etc.

DVD player, etc.

Speakers (see page 17 for hookup details)

Which Connections Should I Use?

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide.

For video components, you must make an audio connection and a video connection.

Audio Connection Formats

Audio equipment can be connected to the AV receiver by using any of the following audio connection formats: analog, optical, coaxial, analog multichannel, or HDMI.

When you connect audio equipment to an

HDMI, OPTICAL, or COAXIAL input, you must assign that input to an input selector (see

pages 45).

Audio Signal Flow Chart


AV receiver

HDMI Multichannel Optical Coaxial Analog

When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog TAPE OUT.

MD recorder, etc.

HDMI Optical Analog

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority:

HDMI, digital, analog (including multichannel). You can specify which audio inputs the AV receiver checks for the

presence of a signal in the “Automatic Audio Input Selection Setup” on page 47.

22



—Continued

Video Connection Formats

Video equipment can be connected to the AV receiver by using any one of the following video connection formats: composite video,

S-Video, component video, or HDMI, the latter offering the best picture quality.

Video input signals flow through the AV receiver as shown, with composite video, S-

Video, and component video sources all being upconverted for the HDMI output.

The composite video, S-Video, and component video outputs pass through their respective input signals as they are.

When you connect audio equipment to an

HDMI or COMPONENT input, you must assign that input to an input selector (see pages

44 and 45).

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, component video, S-Video, composite video. However, for component video only, regardless of whether a component video signal is actually present, if a component video input is assigned to the input selector, that component video input will be selected. And if no component video input is assigned to the input selector, this will be interpreted as no component video signal being present.

In the Signal Selection Example shown on the right, video signals are present at both the

S-Video and composite video inputs, however, the S-Video signal is automatically selected as the source and video is output by the S-Video and HDMI outputs.

Video Signal Flow Chart


AV receiver


AV receiver


Composite

Composite

MONITOR OUT

S-Video Component

HDMI

Signal Selection Example


Composite

S-Video

IN

Component

S-Video

IN

Component

HDMI

HDMI

Composite

MONITOR OUT

S-Video Component

HDMI

The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the composite video or S-Video MONITOR OUT, or the COMPONENT VIDEO OUT, use the DTR-5.9’s display when changing settings.

23



—Continued

Connecting a TV or Projector

Step 1: Video Connection

Choose a video connection that matches your TV ( , , or

C

), and then make the connection.

Step 2: Audio Connection

Choose an audio connection that matches your TV (

a

,

b

, or

c



• With connection

a

, you can listen to and record audio from your TV or listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection

b

or

c

. (To record or listen in Zone 2 as well, use

a

and

b

,

a c

Connection

A

B

C a b c

AV receiver

COMPONENT VIDEO OUT

MONITOR OUT S

MONITOR OUT V

GAME/TV IN L/R

DIGITAL IN COAXIAL 2

DIGITAL IN OPTICAL 1

Signal flow

⇒

⇒

⇒

⇐

⇐

⇐

TV

Component video input

S-Video input

Composite video input

Analog audio L/R output

Digital coaxial output

Digital optical output

Picture quality

Best

Better

Standard

b

ANTENNA

FM

75

C c

A a

24

COAXIAL

OUT

OPTICAL

OUT

Y P

B

P

R

COMPONENT VIDEO IN

L

AUDIO

OUT

R

S VIDEO

IN

VIDEO

IN

Connect one or the other

Connection

c

must be assigned

(see page 45)


Hint!

If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see

pages 27 and 29).



—Continued

Connecting a DVD player


Choose a video connection that matches your DVD player ( , , or

C

) , and then make the connection.

You must connect the AV receiver to your TV with the same type of connection.


Choose an audio connection that matches your DVD player (

a

,

b

, or

c


• With connection

a

, you can listen to and record audio from a DVD or listen in Zone 2.


b

or

c


a

and

b

,

a c

• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection

a

.

Connection

A

B

C a b c

AV receiver

COMPONENT VIDEO IN 1

DVD IN S

DVD IN V

DVD IN FRONT L/R



Signal flow

⇐

⇐

⇐

⇐

⇐

⇐

DVD player

Component video output

S-Video output

Composite video output




Picture quality

Best

Better

Standard

b

SIRIUS

AM

ANTENNA

FM

75 c a

A

COAXIAL

OUT

OPTICAL

OUT

Y P

B

P

R


L

AUDIO

OUT

R

S VIDEO

OUT

VIDEO

OUT


Connection

c

must be

assigned (see page 45)

DVD player

To connect a DVD player or DVD-Audio/SACD-capable player with a

multichannel analog audio output, see page 26.

25



—Continued

Hooking Up the Multichannel Input

If your DVD player supports multichannel audio formats such as DVD-Audio and SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel input.

Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT

L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your

DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV receiver’s

SURR BACK L/R jacks.

To select the multichannel input, see “Basic AV Receiver Operation” on page 48. To adjust the subwoofer sensitivity for

the multichannel input, see “Hardware Setup” on page 89.

SIRIUS

AM

ANTENNA

FM

75

L

R

FRONT

7.1 ch

5.1 ch

SURR

DVD

CENTER SURR BACK

L

R

SUB

WOOFER

L

FRONT

R L

SURROUND

R

CENTER SUB

WOOFER

L

SURR

BACK

R

DVD player

26



—Continued

Connecting a VCR or DVR for Playback

Hint!

With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs.


Choose a video connection that matches your VCR or DVR ( , , or

C

)

, and then make the connection. You must connect the AV receiver to your TV with the same type of connection.


Choose an audio connection that matches your VCR or DVR (

a

,

b

, or

c


• With connection

a

, you can listen to the VCR or DVR in Zone 2.


b

or

c

. (To listen in Zone 2 as well, use

a

and

b

, or

a

and

c

.)

Connection

A

B

C a b c

AV receiver


VCR/DVR IN S

VCR/DVR IN V

VCR/DVR IN L/R



Signal flow

⇐

⇐

⇐

⇐

⇐

⇐

VCR or DVR


S-Video output





Picture quality

Best

Better

Standard

AM

SIRIUS b

ANTENNA

FM

75 c a

A

COAXIAL

OUT


Connection

b

must be


OPTICAL

OUT

Y P

B

P

R


L

AUDIO

OUT

R

S VIDEO

OUT

VIDEO

OUT

VCR or DVR

27



—Continued

Connecting a VCR or DVR for Recording


Choose a video connection that matches your VCR or DVR (

A

or

B

), and then make the connection. The video source to be recorded must be connected to the AV receiver via the same type of connection.


Choose an audio connection that matches your VCR or DVR (

a

or

b


Connection

A

B a b

AV receiver

VCR/DVR OUT S

VCR/DVR OUT V

VCR/DVR OUT L/R

DIGITAL OPTICAL OUT

Signal flow VCR or DVD recorder

⇒

⇒

⇒

⇒

S-Video input

Composite video input

Audio L/R input

Digital optical input

Picture quality

Better

Standard

AM

SIRIUS

ANTENNA

FM

75

B

A b a

OPTICAL

IN

L

AUDIO

IN

R

S VIDEO

IN

VIDEO

IN

28

VCR or DVR

Notes:

• The AV receiver must be turned on for recording. Recording is not possible while it’s on Standby.

• If you want to record directly from your TV or another video source without going through the AV receiver, connect the audio and video outputs from your TV or other video component directly to the recording VCR/DVR’s audio and video inputs. See the manuals supplied with your TV or VCR/DVR for details.

• Video signals connected to composite video inputs can only be recorded via the VCR/DVR OUT V jack. So if your source TV or VCR is connected to a composite video input, the recording VCR/DVR must be connected to the

VCR/DVR OUT V jack. Likewise, video signals connected to S-Video inputs can only be recorded via the VCR/DVR

OUT S jack. So if your source TV or VCR is connected to an S-Video input, the recording VCR/DVR must be connected to the VCR/DVR OUT S jack.



—Continued

Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source

Hint!

With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs.


Choose a video connection that matches the video source ( , , or

C

)

, and then make the connection.

You must connect the AV receiver to your TV with the same type of connection.


Choose an audio connection that matches the video source (

a

,

b

, or

c


• With connection

a

, you can listen to and record audio from the video source or listen in Zone 2.


b

or

c


a

and

b

,

a c

Connection

A

B

C a b c

AV receiver


CBL/SAT IN S

CBL/SAT IN V

CBL/SAT IN L/R



Signal flow

⇐

⇐

⇐

⇐

⇐

⇐

Video source


S-Video output





Picture quality

Best

Better

Standard

b

SIRIUS

AM

ANTENNA

FM

75 c

A a

COAXIAL

OUT

OPTICAL

OUT


Connection

c

must be


Y P

B

P

R


L

AUDIO

OUT

R

S VIDEO

OUT

VIDEO

OUT

Satellite, cable, set-top box, etc.

29



—Continued

Connecting a Game Console


Choose a video connection that matches your game console ( , , or

C

) , and then make the connection.

If you use connection

A

, you must connect the AV receiver to your TV with the same type of connection.


Choose an audio connection that matches your DVD player (

a

,

b

, or

c


• With connection

a

, you can listen to and record audio from your game console or listen in Zone 2.


b


a

and

b

.)

Connection

A

B

C a b

AV receiver


GAME/TV IN S

GAME/TV IN V

GAME/TV IN L/R

DIGITAL OPTICAL IN 1

Signal flow

⇐

⇐

⇐

⇐

⇐

Game console


S-Video output




Picture quality

Best

Better

Standard

SIRIUS

AM

ANTENNA

FM

75

C b

A a

OPTICAL

OUT

Y P

B

P

R


L

AUDIO

OUT

R

S VIDEO

OUT

VIDEO

OUT

Game Console

30



—Continued

Connecting Components with HDMI

About HDMI

Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, or multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface),

*1

so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.)

The AV receiver uses HDCP (High-bandwidth Digital Content Protection), so only HDCP-compatible components will display a picture.

The AV receiver’s HDMI interface is based on the following standard:

Repeater System, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby

TrueHD, Dolby Digital Plus, SA-CD and Multichannel PCM

Supported Audio Formats

• 2-channel linear PCM (16/20/24 bit/32–192kHz)

• Multichannel linear PCM (7.1 ch, 32–192kHz)

• Bitstream (Dolby Digital, Dolby Digital Plus, DTS, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby

TrueHD, DSD)

Your DVD player must be able to output these formats from its HDMI OUT.

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection),

*2

a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

Use a commercially available HDMI cable (supplied with some components) to connect the AV receiver’s HDMI OUT to the HDMI input on your TV or projector.

*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG

*3

in 1999.

*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

*3 DDWG (Digital Display Working Group): Led by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open industry group’s objective is to address the industry's requirements for a digital connectivity specification for high-performance PCs and digital displays.

31



—Continued

Making HDMI Connections

If you have an HDMI-compatible player, you can connect it to the AV receiver with an HDMI cable.

Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV, projector, and so on.

Step 2: Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 44).

■

Video Signals

Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.

Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Connection Formats” on page 23 for more information.

■

Audio Signals

Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV

receiver. Normally, they are not output by the HDMI OUT, unless the Audio TV Out setting is set to On (see page 91).

Hint!

To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the Audio TV Out setting to On (see page 91), and set your DVD player’s HDMI audio output setting to PCM.

HDMI

OUT

HDMI

IN

TV

DVD player

IN 1

(DVD) OUT

SIRIUS

AM

ANTENNA

FM

75

32

Notes:

• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.



—Continued

Connecting a Camcorder or Other Device

Step 1: Make the video connection

A

.

Step 2: Make the audio connection a

.

a

L

AUX Input

Audio R

L AUDIO

OUT

R

A

AUX Input

Video

VIDEO OUT

Camcorder, etc.

Connection

A a

AV receiver

AUX Input Video

AUX Input L-Audio-R

Signal flow

⇐

⇐

Camcorder or console



Connecting a Power Amplifier

If you want to use a more powerful power amplifier and use the AV receiver as a preamp, connect it to the PRE OUT jacks, and connect all speakers and the subwoofer to the power amplifier. If you have a powered subwoofer, connect it to this AV receiver’s PRE OUT SUBWOOFER jack.

SIRIUS

AM

ANTENNA

FM

75

1. Subwoofer

2. Front left speaker

3. Center speaker

4. Front right speaker

5. Surround left speaker

1 2 3 4

6. Surround right speaker

7. Surround back left speaker

8. Surround back right speaker

5 6 7 8

Power amplifier

33


34


—Continued

Connecting a CD Player or Turntable

■

CD Player or Turntable (MM) with Built-in Phono Preamp

Step 1:

Choose a connection that matches your CD player (

a

,

b

, or

c

). Use connection

a

for a turntable with a built-in phono preamp.


b

COAXIAL

2

(CBL/SAT) c

OPTICAL

2

(CD)

SIRIUS

R

CD a

AM

IN

FM

75

L

R

AUDIO

OUTPUT

must be assigned (see

page 45)

IN

L

CD

R a

COAXIAL

OUT

L R

OPTICAL

OUT

AUDIO

OUT

CD player

Turntable (MM) with built-in phono preamp

• With connection

a

, you can listen to and record audio from the CD player or listen in Zone 2.

• To connect the CD player digitally, use connection

b

or

c


a

and

b

, or

a

and

c

.)

Connection a b c

AV receiver

CD IN L/R



Signal flow

⇐

⇐

⇐

CD or turntable




■

Turntable (MM) with no Phono Preamp Built-in

A phono preamp is necessary to connect a turntable that doesn’t have a phono preamp built-in.

■

Turntable with an MC (Moving Coil) Cartridge

An MC head amp and phono preamp are necessary to connect a turntable with an MC (Moving Coil) cartridge.

SIRIUS

AM

ANTENNA

FM

75

SIRIUS

AM

ANTENNA

FM

75

L

IN

R

CD

AUDIO

OUTPUT

L

R

Phono preamp

AUDIO

OUTPUT

L

R

AUDIO

INPUT

L

R

L

IN

R

CD

AUDIO

OUTPUT

L

R

Phono preamp

L

AUDIO

INPUT

R

MC head amp or

MC transformer

AUDIO

OUTPUT

L

R

AUDIO

OUTPUT

L

R

AUDIO

INPUT

L

R



—Continued

Connecting a Cassette, CDR, MiniDisc, or DAT Recorder

Step 1:

Choose a connection that matches your recorder (

a

,

b

,

c

, or

d


b

COAXIAL

2

(CBL/SAT) c

OPTICAL

2

(CD) d

DIGITAL

OUT

SIRIUS

AM

ANTENNA

FM

75

L

IN

R

TAPE a a

L

R

TAPE


These connections must be


COAXIAL

OUT

OPTICAL

OUT

OPTICAL

IN

L

AUDIO

IN

R L

AUDIO

OUT

R

Cassette, CDR, MD, etc.

• With connection

a

, you can play and record or listen in Zone 2.

• To connect the recorder digitally for playback, use connections

a

and

b

, or

a

and

c

.

• To connect the recorder digitally for recording, use connection

d

.

Connection a b c d

AV receiver

TAPE IN L/R

TAPE OUT L/R



DIGITAL OPTICAL OUT

Signal flow

⇐

⇒

⇐

⇐

⇒

Cassette, CDR, MD, or DAT recorder


Analog audio L/R input



Digital optical input

35



—Continued

Connecting an RI Dock

Not all iPod models output video.

For information about which iPod models are supported by the RI Dock, see the RI Dock’s instruction manual.

■

If Your iPod Supports Video:

Connect your RI Dock’s audio output jacks to the

AV receiver’s GAME/TV IN L/R jacks, and connect its video output jack to the AV receiver’s GAME/TV

IN V jack.

■

If Your iPod Doesn’t Support Video:

Connect your RI Dock’s audio output jacks to the

AV receiver’s TAPE IN L/R jacks.

IN

L

TAPE

R

GAME/TV

V

IN

L

R

GAME/TV

If you have an Onkyo DS-A1 RI Dock, connect its video output jack to the AV receiver’s GAME/TV IN S jack.

Notes:

• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time

(see page 101).

• Connect the RI Dock to the AV receiver with an

cable (see page 37).

• Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.

• Set the AV receiver’s Input Display to DOCK (see page 46).

• See the RI Dock’s instruction manual for more information.

36



—Continued

Connecting Integra/Onkyo Components

Step 1: Make sure that each Integra/Onkyo component is connected to the AV receiver with an analog audio cable

(RCA).

Step 2: Make the necessary connections (see illustration below).

Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 46).

With (Remote Interactive), you can use the following special functions:

Auto Power On/Standby

When you start playback on a component connected via , if the AV receiver is on Standby, it will automatically turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all components connected via will also go on Standby.

Direct Change

When playback is started on a component connected via , the AV receiver automatically selects that component as the input source. If your DVD player is connected to the AV receiver’s DVD IN (multichannel input), you’ll need to

press the [Multi CH] button repeatedly and select Multich to hear all channels (see page 48), as the Direct Change

function selects the DVD IN FRONT L/R jacks.

Remote Control

You can use the AV receiver’s remote controller to control your other -capable Integra/Onkyo components. You must

enter the appropriate remote control code first (see page 101). And remember to point the remote controller at the AV

receiver and not the other component.

Notes:

• Use only cables for connections. cables are supplied with Integra/Onkyo players (DVD, CD, etc.).

• Some components have two jacks. You can connect either one to the AV receiver. The other jack is for connecting additional -capable components.

• Connect only Integra/Onkyo components to jacks. Connecting other manufacturer’s components may cause a malfunction.

• Some components may not support all functions.

Refer to the manuals supplied with your other Integra/Onkyo components.

• While Zone 2 is on, the Auto Power On/Standby and

Direct Change functions do not work.

REMOTE

CONTROL e.g., CD player e.g., DVD player

SIRIUS

AM

L

IN

ANTENNA

FM

75

R

CD

FRONT

L

R

DVD

R L

ANALOG

AUDIO OUT

R L

ANALOG

AUDIO OUT

37


Turning On the AV Receiver

On/Standby

Standby indicator

On/Standby

Receiver

38

Connecting the Power Cord

• Before connecting the power cord, connect all your speakers and AV components.

• Plug the end of the power cord into a suitable wall outlet.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

Turning On and Standby


AV receiver or

Remote controller

On the AV receiver, press the [On/Standby] button.

On the remote controller, press the [Receiver] Remote Mode button, followed by the [On/Standby] button.

The AV receiver comes on, the display lights up, and the Standby indicator goes off.

To turn the AV receiver off, press the [On/Standby] button, or press the remote controller’s [On/Standby] button. The AV receiver will enter Standby mode. To prevent any loud surprises the next time you turn on the AV receiver, turn down the volume before you turn it off.

Up and Running in a Few Easy Steps

To get your system up and running with the minimum of fuss, here’s a few pointers to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once.

■ Do the automatic speaker setup—this is essential!

See “Automatic Speaker Setup” on page 39.

■ Did you connect a component to an HDMI input,

component video input, or digital audio input?

If you did, see “HDMI Input Setup” on page 44, “Component Video

Input Setup” on page 45, or “Digital Input Setup” on page 45 respec-

tively.

■ Did you connect an Onkyo MD recorder, CD recorder, or RI

Dock?

If you did, see “Changing the Input Display” on page 46.

HDMI

OUT IN

Y

P

B

P

R

COAXIAL

OPTICAL

TAPE

MD recorder, CD recorder,

RI Dock


First Time Setup

This section explains the settings that you need to make before using the AV receiver for the very first time.

Using Audyssey 2EQ

Automatic Speaker Setup

With the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey 2EQ then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Enabling Audyssey 2EQ allows you to also use Audyssey Dynamic EQ, which maintains the proper octave-to-octave balance at any volume level. (See

page 80)

Notes:

• If any of your speakers is 4 ohms, change the

Speaker Impedance setting before running the

automatic speaker setup (see page 43).

• If the AV receiver is muted, it will be unmuted automatically when the automatic speaker setup starts.

• Automatic speaker setup cannot be performed while a pair of headphones is connected.

• It takes about 10 minutes to complete the automatic speaker setup for three positions. Total measurement time varies depending on the speakers.

• Do not connect or disconnect any speakers during the automatic speaker setup.

Measurement Positions

To create a listening environment in which several people can enjoy your home theater simultaneously,

Audyssey 2EQ takes measurements at three positions within the listening area.

A

First measurement point

This is the center point of the listening area, or the listening position.

B

Second measurement point

The right side of the listening area.

C

Third measurement point

The left side of the listening area.

The distances between points

1

and

2

and points

1 and

3

must be at least 1 meter.

From the examples below, choose the listening area that best matches yours and place the microphone accordingly when prompted.

1

2, 8

TV TV TV

3-7

TV TV TV

TV TV

: Listening area

:

Listening position

TV

The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the composite video or S-Video MONITOR OUT, or the COMPONENT VIDEO OUT, use the DTR-

5.9’s display when changing settings.

1

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the

AV receiver is connected.

39


40


—Continued

2

Put the speaker setup microphone at measurement point 1

(page 39), and connect it to the

Setup MIC jack.

Auto Speaker Setup

AUDYSSEY

Please place microphone at center of listening area at ear height.

3

4

Push Enter : Next

Notes:

• For all measurements, the microphone capsule should point directly at the ceiling.

• If there’s an obstacle between the microphone and any speaker, the automatic setup will not work correctly. Set up the room as you would when enjoying a DVD.

• Positioning the microphone close to where your ears would normally be will provide better results. You can adjust the height of the microphone by using a tripod or level table.

• Do not attempt to hold the microphone in your hand during measurements as this will produce incorrect results.

Press [Enter].

The automatic speaker setup starts.


AUDYSSEY

Do not unplug microphone.

Please keep quiet.

Now Measuring. . .

5

6

A test tone is output by each speaker in turn, as the Audyssey 2EQ function determines which speakers are connected. This takes a few minutes.

Note:

• Quiet the room as much as possible.

Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices, and refrain from talking.

The following screen appears.


AUDYSSEY

Please place microphone at right end of listening area at ear height.


Move the speaker setup microphone to measurement point 2

(page 39), then press [Enter].

Audyssey 2EQ performs more measurements. This takes a few minutes.

The following screen appears.


AUDYSSEY

Please place microphone at left end of listening area at ear height.


Move the speaker setup microphone to measurement point 3

(page 39), then press [Enter].

Audyssey 2EQ performs more measurements. This takes a few minutes.

When the measurements are complete, the following screen appears.


AUDYSSEY

Calculating...



—Continued

7

8

When the calculations are complete, the following screen appears.


Review Speaker configuration

Subwoofer : No

AUDYSSEY

Save

Cancel

Surr Back

Surr Back Ch

:

:

40Hz

1ch

Use the Up and Down [ ]/[ ] buttons to select an option, and then press [Enter].

The options are:

Save:

Save the calculated settings and exit the automatic speaker setup.

Cancel:

Cancel the automatic speaker setup.

Note:

• You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using the Left and Right [ ]/[ ] buttons.

Disconnect the speaker setup microphone.


Please unplug microphone.

AUDYSSEY

Note:

• When the automatic speaker setup is complete, the

Equalizer Settings (page 86) will be set to “Audyssey.”

Error Messages

While the automatic speaker setup is in progress, one of the following error messages may appear:

❏

Ambient noise is too high


AUDYSSEY

Ambient noise is too high.

Retry

Cancel

This message appears if the background noise is too loud and the measurements cannot be performed properly.

Remove the source of the noise and try again.

Retry

: Return to the measured point immediately before and start set up again.

Cancel

: Cancel the automatic speaker setup.

❏

Speaker Detect Errors


- - - - - Speaker Detect Error - - - - -

FL

SL

SBL

C

: Yes

: ---

: ---

: Yes

FR

SR

SBR

SW

: No

: ---

: ---

: ---

Retry

Cancel

AUDYSSEY

One of the front speakers has not been detected.

Retry

Cancel



FL

SL

SBL

C

: Yes

: ---

: ---

: Yes

FR

SR

SBR

SW

: Yes

: No

: ---

: ---

AUDYSSEY

One of the surround speakers has not been detected.



FL

SL

SBL

C

: Yes

: ---

: ---

: Yes

FR

SR

SBR

SW

: Yes

: No

: Yes

: ---

AUDYSSEY

Retry

Cancel

The surround back speakers have been detected but the surround speakers haven’t.

41



—Continued



FL

SL

SBL

C

: Yes

: ---

: No

: Yes

FR

SR

SBR

SW

: Yes

: Yes

: Yes

: ---

Retry

Cancel

AUDYSSEY

The right surround back speaker has been detected but the left surround back speaker hasn’t.



FL

SL

SBL

C

: Error

: Yes

: Yes

: Yes

FR

SR

SBR

SW

: Yes

: Yes

: Yes

: Yes

Retry

Cancel

AUDYSSEY

There is a problem with a speaker. The speaker may be broken or the subwoofer may be emitting sound that is too high.


AUDYSSEY

To Retry the Automatic Speaker Setup

Press the [Enter] button.

Make sure speakers that cannot be detected are connected properly.

Changing the Speaker Settings Manually

If you wish to make changes to the settings found during the automatic speaker setup, follow the directions on

pages 82–86.

Using a Powered Subwoofer

If you’re using a powered subwoofer, as it outputs very low-frequency sound and its position is usually low down, it may not be detected by the automatic speaker setup. In this case, increase the subwoofer’s volume, select its highest crossover frequency, and then try running the automatic speaker setup again. Note that if the volume is set too high and the sound distorts, it may not be detected, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

Retry

Cancel

Speaker Detect Error

The number of speakers detected on the second or third measurement was different to the number detected on the first measurement.

Make sure speakers that cannot be detected are connected properly.

Retry

: Return to step 2 and try again.

Cancel


❏

Write Error


AUDYSSEY

Writing Error!

Retry

Cancel

42

This message appears if saving fails.

Try saving again. If this message appears after 2 or 3 attempts, the AV receiver is probably malfunctioning.

Contact the dealer.

Retry

: Return to step 2 and try again.

Cancel




—Continued

Speaker Settings

If you change these settings, you must run the auto-

matic speaker setup again (see page 39).

2

Use the Up and Down [ ]/[ ] buttons to select “2. Speaker

Setup,” and then press [Enter].

Enter

Setup

Receiver

3

Use the Up and Down [ ]/[ ] buttons to select “1. Speaker Settings,” and then press [Enter].

If the impedance of any speaker is 4 ohms or more but less than 6, set the Speaker Impedance to 4 ohms.

North American models do not support speakers with an impedance of less than 6 ohms.

To use bi-amping, you must change the Speaker Type

setting. For hookup information, see page 18.

Notes:

• When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

• Before you change these settings, turn down the volume.



1

Press the [Receiver] button, followed by the [Setup] button.

The main menu appears onscreen.

If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV.

4

5

6

Use the Up and Down [ ]/[ ] buttons to select “Speaker

Impedance,” and use the Left and

Right [ ]/[ ] buttons to select:

4 ohms:

Select if the impedance of any speaker is 4 ohms or more but less than 6.

6 ohms:

Select if the impedances of all speakers are between 6 and

16 ohms.

Use the Up and Down [ ]/[ ] buttons to select “Speaker Type,” and use the Left and Right

[ ]/[ ] buttons to select:

Normal:

Select this if you’ve connected your front speakers normally.

Bi-Amp:

Select this if you’ve connected your front speakers for bi-amped operation.

Press the [Setup] button.

Setup closes.

Note:

• This procedure can also be performed on the AV receiver by using its [Setup], [Enter], and arrow buttons.

43



—Continued

HDMI Input Setup

If you connect a video component to an HDMI IN, you must assign that input to an input selector. For example, if you connect your DVD player to HDMI IN 1, you must assign HDMI IN 1 to the DVD input selector.

These are the default assignments.

Input selector

DVD

VCR/DVR

CBL/SAT

GAME/TV

AUX

TAPE

CD

Audio input

HDMI1

HDMI2

HDMI3

HDMI4

- - - - -

- - - - -

- - - - -

1

2

4

Use the Up and Down [ ]/[ ] buttons to select an input selector, and use the Left and Right


HDMI1:

Select if the video component is connected to HDMI

IN 1.

HDMI2:

HDMI3:


IN 2.


IN 3.

HDMI4:

- - - - -:


IN 4.

Select if you’re not using the

HDMI IN1–IN4.


Setup closes.




5

Use the Up and Down [ ]/[ ] buttons to select “1. Input

Assign,” and then press [Enter].

Notes:

• Each HDMI IN cannot be assigned to more than one input selector.

• When an HDMI IN is assigned to an input selector as explained here, the digital audio input for that input selector is automatically set to the same HDMI IN.

See “Digital Input Setup” on page 45.


3

Use the Up and Down [ ]/[ ] buttons to select “1-1. HDMI

Input,” and then press [Enter].

44



—Continued

Component Video Input Setup

If you connect a video component to a COMPONENT

VIDEO IN, you must assign that input to an input selector. For example, if you connect your DVD player to COMPONENT VIDEO IN 2, you must assign COM-

PONENT VIDEO IN 2 to the DVD input selector.


Input selector

DVD

VCR/DVR

CBL/SAT

Game/TV

AUX

Tape

CD

Audio input

IN1

- - - - -

IN2

- - - - -

- - - - -

- - - - -

- - - - -

1

2

3

4

5

Use the Up and Down [ ]/[ ] buttons to select an input selector, and use the Left and Right


IN1:

Select if the video component is connected to COM-

PONENT VIDEO IN 1.

IN2:

Select if the video component is connected to COM-

PONENT VIDEO IN 2.

- - - - -:

Select if you’re not using the

COMPONENT VIDEO IN1 or IN2.


Setup closes.




Note:




Use the Up and Down [ ]/[ ] buttons to select “1-2. Component Video Input,” and then press

[Enter].

Digital Input Setup

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to OPTICAL IN 1, you must assign OPTICAL IN 1 to the CD input selector.


Input selector

DVD

VCR/DVR

CBL/SAT

Game/TV

AUX

Tape

CD

Audio input

COAX1

- - - - -

COAX2

OPT1

- - - - -

- - - - -

OPT2

1




45



—Continued

2



3

Use the Up and Down [ ]/[ ] buttons to select “1-3. Digital

Audio Input,” and then press

[Enter].

the“Automatic Audio Input Selection Setup” on page 47 to the same input (e.g., COAX1 (Auto) or

COAX2 (Auto)).


Changing the Input Display

If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT jacks, or connect an RI Dock to the GAME/TV IN jacks, for to work properly, you must change this setting.

This setting can only be changed on the AV receiver.

1, 2 1, 2

4

5

Use the Up and Down [ ]/[ ] buttons to select an input selector, and then use the Left and


COAX1

: Select if the component is connected to DIGITAL IN

COAXIAL 1.

COAX2


COAXIAL 2.

OPT1


OPTICAL 1.

OPT2


OPTICAL 2.

- - - - -:

Select if the component is connected to an analog input.


Setup closes.

46

• When an HDMI IN is assigned to an input selector in

“HDMI Input Setup” on page 44, this input assign-

ment is automatically set to the same HDMI IN. And in addition to the usual inputs (e.g., COAX1, COAX2, etc.), you can also select HDMI inputs. If you change the input assignment from an HDMI IN to one of the other inputs (e.g., COAX1 or COAX2), be sure to set

iPod photo:

If you’re using an iPod photo with the

DS-A1 Remote Interactive Dock, connect the DS-A1 to the GAME/TV IN jacks.

1

or

Press the [Tape] or [Game/TV] input selector button so that

“TAPE” or “GAME/TV” appears on the display.

2

or

Press and hold down the [Tape] or [Game/TV] input selector button (about 3 seconds) to change the setting.

Repeat this step to select MD, CDR, or

DOCK.

For the Tape input selector, the setting changes in this order:

TAPE

→

MD

→

CDR

DOCK

→

For the Game/TV input selector, the setting changes in this order:

GAME/TV

↔

DOCK

Notes:

• DOCK can be selected for the Tape input selector or

Game/TV input selector, but not both at the same time.



—Continued

Automatic Audio Input Selection

Setup

1

When an input source is selected, the AV receiver checks the relevant audio inputs for the presence of an audio signal and automatically selects an input. With this setting, you can specify which audio inputs the AV receiver will check for signals.

1

2

2, 3

Press the input selector button for the input selector whose setting you want to change.

The setting for the Tuner input selector cannot be changed and is fixed at “Analog.”

Press and hold the [Enter] button.

The current setting is displayed.

3

Press the [Enter] button repeatedly to select an option.

HDMIx (Auto):

This option can be selected when an

HDMI input is assigned to an input

selector (page 44). When this option is

selected, the relevant HDMI, digital, and analog inputs will be checked for the presence of an audio signal. If signals are present at more than one input, the inputs will be selected in the following order of priority: HDMI, digital, analog.

COAXx (Auto)/OPTx (Auto):

This option can be selected when a digital input is assigned to an input selector

(page 45). When this option is selected,

the relevant digital and analog inputs will be checked for the presence of an audio signal. If signals are present at more than one input, the inputs will be selected in the following order of priority: digital, analog. Any audio signals present at the HDMI inputs will not be output.

Analog:

When this option is selected, the signal from the relevant analog audio input is output. Any audio signals present at

HDMI or digital inputs will not be output.

Note:

• You can select a different option for each input selector.

47


Playing Your AV Components

Basic AV Receiver Operation

3

1

3

48

1

1

AV receiver

Use the AV receiver’s input selector buttons to select an input source.

Remote controller To select an input source with the remote controller, press its Input Selector buttons.

To listen to a DVD player connected to the multichannel DVD input (page 26), press

the AV receiver’s [Multi CH] button. The MULTI CH indicator will appear on the display.

Note:

• While the multichannel DVD input is selected, the Speaker Configuration settings on

page 82 are ignored, and signals from the multichannel input are fed to the speakers

as they are.

2

3

AV receiver


4

Start playback on the source component.

To watch a DVD or other video source, on your TV, select the video input that’s connected to the AV receiver’s COMPONENT VIDEO OUT, HDMI OUT, or MONITOR

OUT.

On some DVD players, you may need to change the digital or HDMI audio output settings.

To adjust the volume, use the Master Volume control or the remote controller’s [VOL] button.

Since the AV receiver is designed for home theaters, it has a wide volume range for precise adjustment. The volume can be set to Min, 1 through 79, or Max.

The maximum volume level can be limited with the Maximum Volume setting. See on

page 88.

Select a listening mode and enjoy!

See “Using the Listening Modes” on page 67.


Common Functions

This section explains functions that can be used with any input source.

Display

Press

[Receiver] first

Muting

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press the [Receiver] Remote

Mode button, and then press the remote controller’s [Muting] button.

The output is muted and the MUTING indicator flashes on the display.

Dimmer

Display

Sleep

Phones Dimmer

Setting the Display Brightness

You can adjust the brightness of the display.



Mode button, and then press the remote controller’s [Dimmer] button repeatedly to select: dim, dimmer, or normal brightness.

You can also use the AV receiver’s

[Dimmer] button (not European models).

AV receiver

To unmute the AV receiver,

press the remote controller’s [Muting] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off.

Muting is cancelled when the AV receiver is set to

Standby.

Using the Sleep Timer

With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period.


Mode button, and then press the remote controller’s [Sleep] button repeatedly to select the required sleep time.

You can set the sleep time from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.

SLEEP indicator

To cancel the sleep timer,

press the [Sleep] button repeatedly until the SLEEP indicator disappears.

To check the remaining sleep time,

press the [Sleep] button. Note that if you press the [Sleep] button while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.

49



—Continued

7

Using Headphones

For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s

Phones jack.

Displaying Source Information

You can display various information about the current input source as follows.


Mode button, and then press the

[Display] button repeatedly to cycle through the available information.

Notes:

• Always turn down the volume before connecting your headphones.

• While the headphones plug is inserted in the PHONES jack, the speakers are turned off. (The Powered Zone 2 speakers are not turned off.)

• When you connect a pair of headphones, the listening mode is set to Stereo, unless it was already set to

Mono, Stereo, or Direct, in which case it stays the same.

• When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones.

Note:

• This procedure can also be performed on the AV receiver by using its [Display] button.

The following information can typically be displayed:

Input source & volume*

1

Signal format*

2 or sampling frequency

Input source & listening mode

*1 When AM or FM radio is used, the band, preset number, and frequency are displayed.

*2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears.

50



—Continued

Specifying the Digital Signal Format

The following table shows the display indicator for each digital signal format.

Display Format

Dolby Digital

DTS

PCM

PCM

Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually.

• If the beginnings of tracks from a PCM source are cut off, try the PCM setting.

• If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting.

Preset

1

2

Enter

Press and hold the AV receiver’s

[Enter] button for about 3 seconds.

While “Auto” is displayed (about

3 seconds), use the Left and


PCM, DTS, or Auto.

PCM:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound.

DTS:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not

DTS, the DTS indicator will flash and there will be no sound.

Auto (default):

The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

51


Listening to the Radio

AM Frequency Step Setup

(on some models)

3

Use the Up and Down [ ]/[ ] buttons to select “7-3. Tuner,” and then press [Enter].

2, 3

1, 5

1

2–4

4

Use the Left and Right [ ]/[ ] buttons to select:

7–3. Tuner

AM Freqency Setup 9kHz

5

10kHz:

9kHz:

Select if 10kHz steps are used in your area.

Select if 9kHz steps are used in your area.


Setup closes.

For AM tuning to work properly, you must specify the

AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.

1




Note:


2

Use the Up and Down [ ]/[ ] buttons to select “7. Hardware-


52



—Continued

Listening to AM/FM Stations

Tuning Mode Tuning

■

Manual Tuning Mode

1

Press the [Tuning Mode] button so that the AUTO indicator disappears from the display.

Tuner

With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection.

Use the [Tuner] input selector button to select AM or FM.

In this example, FM has been selected.

Band Frequency

(Actual display depends on country.)

Tuning into AM/FM Radio Stations

■

Auto Tuning Mode

1

Press the [Tuning Mode] button so that the AUTO indicator appears on the display.

2

Press and hold the Tuning Up or

Down [ ]/[ ] button.

The frequency stops changing when you release the button.

Press the button repeatedly to change the frequency one step at a time.

The North American model changes FM frequency in

0.2MHz steps, 10kHz steps for AM. For other models it’s 0.05MHz steps for FM and 9kHz (or 10kHz) steps for AM.

In Manual Tuning mode, FM stations will be in mono.

Tuning into Weak FM Stereo Stations

If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to

Manual Tuning mode and listen to the station in mono.

Note:

• You can also use the remote controller’s Up and Down

[ ]/[ ] buttons to tune the radio.

2

Press the Tuning Up or Down

[ ]/[ ] button.

Searching stops when a station is found.

When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM

STEREO indicator also appears.

FM STEREO

AUTO

TUNED

53



—Continued

■

Tuning into Stations by Frequency

You can tune into AM and FM stations directly by entering the appropriate frequency.

Displaying AM/FM Radio Information

Display

Tuner

Press the [Display] button to display the available information.

Band Frequency Preset #

Number buttons

D.TUN

Listening mode

1

2

Press the [Tuner] button repeatedly to select AM r FM, followed by the [D.TUN] button.

(Actual display depends on country.)

Within 8 seconds, use the number buttons to enter the frequency of the radio station.

For example, to tune to 87.5 (FM), press 8, 7, 5.

54



—Continued

Presetting AM/FM Stations

2, 4 3

Selecting Presets

Preset

You can store a combination of up to 40 of your favorite

AM and FM radio stations.

1

Tune into the AM or FM station you want to store as a preset.

2

Press the [Memory] button.

The preset number flashes.

CH +/–

Tuner

3

While the preset number is flashing (about 8 seconds), use the

Preset [ ]/[ ] buttons to select a preset from 1 through 40.

Number buttons

4

Press the [Memory] button again to store the station.

The station is stored and the preset number stops flashing.

Repeat this procedure for all of your favorite stations.

Deleting Presets

2

AV receiver

To select a preset, use the Preset

[ ]/[ ] buttons or the remote controller’s CH [+/–] button.

or


You can also use the remote controller’s buttons, press the

[Tuner] button and then press the number buttons to select a preset directly.

1

2

Select the preset that you want to delete.

See the next section.

While holding down the [Memory] button, press the [Tuning

Mode] button.

The preset is deleted and its number disappears from the display.

55


56


—Continued

Listening to SIRIUS Satellite Radio

®

(North American Models Only)

Important SIRIUS Satellite Radio Information

SIRIUS is available in the US for subscribers with addresses in the continental US and is available in

Canada for subscribers with a Canadian address. To get SIRIUS Satellite Radio a subscription and compatible tuner and antenna are required and sold separately. Visit sirius.com for the most complete and up-to-date channel lineup and information.

“SIRIUS” and the SIRIUS dog logo and related marks are trademarks of SIRIUS Satellite Radio Inc.

Note:

Hardware and required basic monthly subscription are sold separately. Installation costs and other fees and taxes, including a one-time activation fee may apply.

Subscription fee is consumer only. All fees and programming are subject to change.

What is SIRIUS Satellite Radio?

Simply The Best Radio on Radio

TM

with all your favorite entertainment including 100% commercial-free music, plus superior sports coverage, uncensored talk and comedy, world-class entertainment, news, weather and more for your car, home or office. For more information visit sirius.com or siriuscanada.ca

A warning against reverse engineering:

It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the SIRIUS Satellite Radio system.

“SIRIUS” and the SIRIUS dog logo are registered trademarks of

SIRIUS Satellite Radio Inc.

Indoor/outdoor antenna with 21-foot cable

SiriusConnect receiver

AC power

8-pin mini DIN connector cable

SIRIUS

SIRIUS

AM

ANTENNA

FM

75

SIRIUS jack

AV receiver

To use the included antenna indoors, you must place it at a north-, west-, or east-facing window, depending on where you live. If this isn’t possible, you’ll need to install it outside, away from any overhead obstructions.

Positioning the Antenna

For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to determine which area you are in and position the antenna accordingly.

SKY

NORTH

Setting Up the SiriusConnect™ Home

Tuner

The optional SiriusConnect Home tuner kit includes everything for easy home installation, including the SiriusConnect receiver, indoor/outdoor antenna with 21foot cable, 8-pin mini DIN connector cable, and an AC power adapter. See the SiriusConnect Home tuner’s instructions for more information.

Use the 8-pin mini DIN connector cable to connect the

SiriusConnect receiver to the SIRIUS jack on the rear of the AV receiver.

1

5

4

WEST EAST

2 3

HORIZON

SOUTH

Area 1:

Point the antenna toward the sky in the

east

,

northeast

, or

southeast

, either through a window or outside.

Area 2:


north

or

northeast


Area 3:


north

or

northwest


Area 4:


west

,

northwest

, or

southwest


Area 5:

Put the antenna outside and point it

straight up

.

The antenna cannot be used indoors.



—Continued

Setup

Tuner

Receiver

Enter

4

5

Use the Up and Down [ ]/[ ] buttons to select “SAT Radio

Mode.”

Pressing the Left and Right [ ]/[ ] buttons cycles through the following options: None

↔

SIRIUS

None

: Select if you’re not using satellite radio.

SIRIUS

: Select to use SIRIUS Satellite Radio.

When you’ve finished, press the

[Setup] button.

Setup closes.

Setting the Satellite Radio Mode

Before you can listen to SIRIUS Satellite Radio, you must set the Satellite Radio mode to SIRIUS.

1


Mode button, followed by the

[Setup] button.


Menu

1. Input Assign

2. Speaker Setup

3. Audio Adjust

4. Source Setup

5. Listening Mode Preset

6. Miscellaneous

7. Hardware Setup

8. Lock Setup

2

Use the Up and Down [ ]/[ ] buttons to select “7. Hardware


The Hardware Setup menu appears.


1. Remote Control

2. Zone2

3. Tuner

4. Analog Multich

5. HDMI

3

Use the Up and Down [ ]/[ ] buttons to select “3. Tuner,” and then press [Enter].

The Tuner screen appears.

7-3.Tuner

SAT Radio Mode None

Selecting SIRIUS Satellite Radio

AV receiver

On the AV receiver, press the

[Tuner] Input Selector button repeatedly to select SIRIUS.


On the remote controller, press the [Receiver] Remote Mode button, and then press the [Tuner]

Input Selector button repeatedly to select SIRIUS.

If “CHECK SR TUNER” appears on the display, make sure the SiriusConnect receiver is connected properly. If

“ANTENNA ERROR” appears, make sure the antenna is connected properly.

57



—Continued

Signing Up for SIRIUS Satellite Radio

Tuning

Selecting SIRIUS Satellite Radio Channels

There are three ways to select SIRIUS Satellite Radio channels:

1.

2.

3.

Channel Search mode:

Category Search mode:

gory.

select any channel.

select channels by cate-

Direct tuning:

enter channel number.

■

Channel Search Mode

1



[Enter] button repeatedly to select Channel Search mode.

Before you can use SIRIUS Satellite Radio, you must first sign up for an account. You’ll need a major credit card and your

SIRIUS Satellite Radio ID,

which you can get from the AV receiver, as explained below, or from the

SiriusConnect Home tuner package.

1

Use the Tuning Up and Down

[ ]/[ ] buttons to select channel 0.

Your SIRIUS Satellite Radio ID number is displayed. Write it below.

2

ID

To sign up, go to: http://activate.siriusradio.com

Or call: 1-888-539-SIRIUS (7474)

Note:

• Your ID is also displayed on the Satellite Radio screen. See “Positioning the SiriusConnect Home

Antenna” on page 63.

2

Use the Up and Down [ ]/[ ] buttons to select a channel.

Channel number Channel name

You can also use the Left and Right

[ ]/[ ] buttons to select a category.

■

Category Search Mode

1



[Enter] button repeatedly to select Category Search mode.

Receiver

Enter

Return

2

Use the Left and Right [ ]/[ ] buttons to select a category, and use the Up and Down [ ]/[ ] buttons to select a channel in that category.

Number buttons

D.TUN

58



—Continued

■

Direct Tuning

You can select a SIRIUS Satellite Radio channel directly by entering its number.

1



[D.TUN] button.

The [Receiver] button flashes.

3

Use the Tuning Up and Down

[ ]/[ ] buttons to select a channel.

In Channel Search mode, you can select any channel.

In Category Search mode, you can only select channels from the currently selected category.

2

Within 8 seconds, use the number buttons to enter the channel number.

For example, to select channel #20, press 0, 2, 0, or 2, 0, [Enter].

Note:

• While the [Receiver] button is flashing, you cannot select another input source with the remote controller.

Notes:

• If you select an unavailable channel, “INVALID

CHANNEL” appears on the display.

• If you select a channel that you are not subscribed to,

“CALL SIRIUS” appears on the display.

• Channels that are locked must be unlocked before you can listen to them. See “Parental Lock” on page 60 for more information.

Tuning , Preset

Tuning Mode Return

Selecting the Previous Channel:

AV receiver

To listen to the previously selected SIRIUS Satellite Radio channel, press the [Return] button.


Presetting SIRIUS Channels

You can store a combination of up to 40 of your favorite

SIRIUS Satellite Radio channels and AM/FM radio stations as presets.

1

2

Tune into the SIRIUS channel that you want to store as a preset.

Press the [Memory] button.

The preset number flashes.

3

While the preset number is flashing (about 8 seconds), use the

Preset [ ]/[ ] buttons to select a preset from 1 through 40.

Memory Enter

Selecting Channels on the AV receiver:

1

Press the [Tuning Mode] button repeatedly to select Channel

Search mode or Category Search mode.

2

Press [Enter] repeatedly to select a category.

4

Press the [Memory] button again to store the channel.

The channel is stored and the preset number stops flashing.

Repeat this procedure for all of your favorite SIRIUS Satellite Radio channels.

59



—Continued

Setup

Enter

Number buttons

D.TUN

■

Selecting Presets

AV receiver

To select a preset, use the Preset

[ ]/[ ] buttons, or the remote controller’s CH [+/–] button.


2

3

Parental Lock

With SIRIUS Parental Lock, you can lock out channels that you do not want to receive and use a 4-digit PIN number to prevent others from unlocking them.

1



[Setup] button.







2. Zone2

3. Tuner


5. HDMI

You can also use the remote controller’s number buttons to select a preset directly.

■

Deleting Presets

1

2

Select the preset that you want to delete.

See the previous section.

While holding down the [Memory] button, press the [Tuning

Mode] button.

The preset is deleted and its number disappears from the display.

4



7-3.Tuner

SAT Radio Mode

Antenna Aiming

SIRIUS Parental Lock

SIRIUS

Note:

• If the SAT RadioMode is set to None

(see page 57), the “Antenna Aiming” and “SIRIUS Parental Lock” items are not available.

Use the Up and Down [ ]/[ ] buttons to select “SIRIUS Parental Lock,” and then press [Enter].

The SIRIUS Parental Lock screen appears.


Enter Code

0 1 2 3 4 5 6 7 8 9

“Enter : <0>” appears on the display.

60



—Continued

5

6

7

or

Use the number buttons to enter the 4-digit PIN number.

Or

Use the Left and Right [ ]/[ ] buttons to select a number on the screen, and then press [Enter].

Repeat this for each of the four digits in the PIN number.

If you’re entering the PIN number for the very first time, the PIN is stored, and the following screen appears.


Edit Code

Parental Lock

If you’ve already set a PIN number, you must enter the correct PIN to get to this screen. If you enter the wrong PIN, the message “Wrong Code!” appears and you’ll have to enter the PIN again.

Use the Up and Down [ ]/[ ] buttons to select “Parental Lock,” and then press [Enter].


Edit Code

Parental Lock

The Parental Lock screen appears.


Parental Lock

Channel Status

xxxch wwwwwwww Unlocked

:CHANNEL

:STATUS

ENT

RET

:SAVE

:RETURN

Use the Up and Down [ ]/[ ] buttons to select a channel, and use the Left and Right [ ]/[ ] buttons to select Locked or

Unlocked.

The number, name, and status of the currently selected channel is displayed.

When you’ve finished, press

[Enter] to save your changes, or press [Return] to return to the previous screen without saving.

When [Enter] is pressed, the confirmation message “Locked” or “Unlocked” appears.

8

Notes:

• While a channel is locked, it cannot be selected for listening.

• To unlock a channel, you must enter the correct PIN number and change it to Unlocked in step 6.

Changing the PIN Number

1



[Setup] button.


2

3


Setup closes.






2. Zone2

3. Tuner


5. HDMI


Note:


7-3.Tuner

SAT Radio Mode

Antenna Aiming


SIRIUS

Note:

If the SAT RadioMode is set to None


61



—Continued

Setup

D.TUN

Enter

Number buttons

6

7

4

5

or

Use the Up and Down [ ]/[ ] buttons to select “SIRIUS Parental Lock,” and then press [Enter].

The SIRIUS Parental Lock screen appears.


Enter Code

0 1 2 3 4 5 6 7 8 9

Use the number buttons to enter the old 4-digit PIN number.

Or


Repeat this for each of the four digits in the old PIN number.

If you enter the correct PIN number, the following screen appears.


Edit Code

Parental Lock

8

9

or

Use the Up and Down [ ]/[ ] buttons to select “Edit Code,” and then press [Enter].

The New Code screen appears.


Edit Code

New Code

0 1 2 3 4 5 6 7 8 9

Use the number buttons to enter the new 4-digit PIN number.

Or


Repeat this for each of the four digits in the new PIN number.

The Confirm screen appears.


Edit Code

Confirm

0 1 2 3 4 5 6 7 8 9

Confirm the new PIN number by entering it again.

If you confirm the PIN number correctly, the new PIN is saved and the message “Complete” appears.

If you confirm the PIN number incorrectly, “Wrong Code!” appears, and you’ll be returned to step 6 to try again.


Setup closes.

If you enter the wrong PIN number, the message “Wrong Code!” appears and you’ll have to enter the PIN again.

62



—Continued

Display

Setup Tuning

Displaying SIRIUS Satellite Radio

Information

AV receiver

Press the [Display] button repeatedly to cycle through the available information.


Display

Enter

Positioning the SiriusConnect Home

Antenna

You can check the strength of the SIRIUS Satellite Radio signal and adjust the position of the SiriusConnect Home antenna accordingly.

1



[Tuner] button, and [Setup] button.


The following information can be displayed:

Channel name

↓

Channel number & preset number

↓

Category

↓

Artist/composer

↓

Song title

↓

Listening mode

Notes:

• If the category, artist/composer, or song title is not available, “- - -” will be displayed instead.

2






2. Zone2

3. Tuner


5. HDMI

3



7-3.Tuner

SAT Radio Mode

Antenna Aiming


SIRIUS

Note:

• If the SAT RadioMode is set to None


Notes:

• So long as the signal strength is good, you can enjoy

SIRIUS Satellite Radio by using either satellite or terrestrial reception.

• Terrestrial signals are only available in certain areas.

63



—Continued

4

Use the Up and Down [ ]/[ ] buttons to select “Antenna Aiming,” and then press [Enter].

The Antenna Aiming screen appears.

Position the SiriusConnect Home antenna so that as many bars as possible (up to 3) appear on the

SIRIUS Satellite signal strength meter.

Antenna Aiming

SIRIUS

❑

CHECK SR TUNER

Displayed if the SiriusConnect receiver is not connected. Make sure the SiriusConnect receiver is connected properly, and make sure its AC adapter is plugged in.

Satellite Terrestrial

SIRIUS ID 000000000000

If you cannot receive a satellite signal, position the SiriusConnect Home antenna so that as many bars as possible

(up to 3) appear on the SIRIUS Terrestrial signal strength meter.

64

SIRIUS Satellite Radio Messages

The following messages may appear while using

SIRIUS Satellite Radio.

❑

ACQUIRING

The SiriusConnect receiver is acquiring the signal or no signal is present. Make sure the SiriusConnect

Home tuner is connected properly and that there are no obstacles close by.

❑

ANTENNA ERROR

Make sure the SiriusConnect Home tuner is connected properly.

❑

SUB UPDATED

Displayed while your subscription is being updated.

No operations can be performed until this message has cleared.

❑

UPDATING XXX%

Displayed while the channel map is being updated.

Wait until the updating is complete.

❑

SIRIUS UPDATING

Displayed while the SiriusConnect receiver’s firmware is being updated.

❑

INVALID CHANNEL

Displayed if you select an unavailable channel.

❑

CALL SIRIUS

Displayed when you select a channel to which you are not subscribed. Call SIRIUS if you want to subscribe.



—Continued

Using RDS (European models only)

RDS only works in areas where RDS broadcasts are available. When tuned to an RDS station, the RDS indicator appears.

RDS indicator

■

What is RDS?

RDS stands for

Radio Data System

and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. RDS is approved by the

National Radio Systems Committee (NRSC) and is available in North America.

Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.).

The AV receiver supports four types of RDS information:

PS (Program Service)

When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Pressing the [Display] button will display the frequency for 3 seconds.

RT (Radio Text)

When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display (see

page 66).

PTY (Program Type)

This allows you to search RDS radio stations by type

(see page 66).

TP (Traffic Program)

This allows you to search for RDS radio stations that broadcast traffic information (see page 66).

Notes:

• In some cases, the characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received.

This is not a malfunction.

• If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.

RDS Program Types (PTY)

Type

None

News reports

Current affairs

Information

Sport

Education

Drama

Culture

Science and technology

Varied

Pop music

Rock music

Middle of the road music

Light classics

Serious classics

Other music

Weather

Finance

Children’s programmes

Social affairs

Religion

Phone in

Travel

Leisure

Jazz music

Country music

National music

Oldies music

Folk music

Documentary

Alarm test

Alarm

Varied

Pop M

Rock M

Easy M

Light M

Classics

Other M

Weather

Finance

Children

Social

Display

None

News

Affairs

Info

Sport

Educate

Drama

Culture

Science

Religion

Phone In

Travel

Leisure

Jazz

Country

Nation M

Oldies

Folk M

Document

TEST

Alarm!

65



—Continued

Displaying Radio Text (RT)

RT/PTY/TP

4

5

To start the search, press [Enter].

The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search.

When a station you want to listen to is found, press [Enter].

If no stations are found, the message

“Not Found” appears.

When tuned to an RDS station that’s broadcasting text information, the text can be displayed.

RT/PTY/TP

Press the [RT/PTY/TP] button once.

The RT information scrolls across the display.

Notes:

• The message “Waiting” may appear while the AV receiver waits for the RT information.

• If the message “No Text Data” appears on the display, no RT information is available.

Finding Stations by Type (PTY)

2 4, 5

Listening to Traffic News (TP)

2 3

1

You can search for stations that broadcast traffic news.

1

Use the [Tuner] input selector button to select FM.

1

You can search for radio stations by type.

3

1

Use the [Tuner] input selector button to select FM.

2

RT/PTY/TP

3

Press the [RT/PTY/TP] button twice.

The current program type appears on the display.

Use the Preset [ ]/[ ] buttons to select the type of program you want.

See the table on page 65.

2

RT/PTY/TP

3

Press the [RT/PTY/TP] button three times.

If the current radio station is broadcasting TP (Traffic Program), “[TP]” will appear on the display and traffic news will be heard as and when it’s broadcast. If “TP” without square brackets appears, this means that the station is not broadcasting TP.

To locate a station that is broadcasting TP, press [Enter].

The AV receiver searches until it finds a station that’s broadcasting TP.

If no stations are found, the message

“Not Found” appears.

66


Using the Listening Modes

Selecting with the Remote Controller

Selecting the Listening Modes

For a description of each listening mode, see “About the

Listening Modes” on page 74.

• The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check

the format, see “Displaying Source Information” on page 50.

• While a pair of headphones is connected, you can only select the Mono, Direct, or Stereo listening mode.

Movie/TV

Music

Stereo

Game

Selecting on the AV Receiver

Music

■

[Movie/TV] button

This button selects the listening modes intended for use with movies and TV.

■

[Music] button

This button selects the listening modes intended for use with music.

■

[Game] button

This button selects the listening modes intended for use with video games.

■

[Stereo] button

This button selects the Stereo listening mode and All

Channel Stereo listening mode.

Game

Movie/TV

■

[Movie/TV] button

This button selects the listening modes intended for use with movies and TV.

■

[Music] button

This button selects the listening modes intended for use with music.

■

[Game] button

This button selects the listening modes intended for use with video games.

67



—Continued

Listening Modes Available for Each Source Format

Analog and PCM Sources

Source format 32–96 kHz

*1

PCM

176.4/

192kHz

*2

Multi channel

Analog

Multichannel

32–96kHz*

1

Multichannel

2ch

Mono/

Multiplex

176.4/192kHz

*2

Multichannel

2ch

Mono/

Multiplex

Button

[Movie/TV]

[Music]

Listening Mode

Mono

Multichannel

Neo:6

Dolby PLII Movie/

Dolby PLIIx Movie

*3

DolbyEX

Neo:6 Cinema

MonoMovie

*5 *6

TV Logic

*5 *6

AllChStereo

FullMono

T-D

*6

Direct

Stereo

Multichannel

Neo:6

Dolby PLII Music/

Dolby PLIIx Music

*3

DolbyEX

Neo:6 Music

Orchestra

*5 *6

Unplugged

*5 *6

Studio-Mix

*5 *6

AllChStereo

FullMono

Multichannel

Media

CD, TV, radio,

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

DVD

✔

✔

✔

✔

✔

✔

✔

✔

*4

*4

*4

✔

✔

✔

✔

✔

✔

✔

✔

✔

*4

✔

*4

✔

*4

DVD

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*4

✔

✔

✔

✔

[Game]

[Stereo]

Neo:6

Dolby PLII Game/

Dolby PLIIx Game

*3

DolbyEX

AllChStereo

FullMono

T-D

*6

AllChStereo

Stereo

✔

✔

✔

✔

✔

✔ ✔

✔

✔

✔

✔

*4

✔

✔

✔

✔

✔

✔

✔

✔

*1. 32/44.1/48/88.2/96kHz

*2. DVD-Audio discs output multichannel 176.4/192kHz PCM only via HDMI.

*3. If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.

*4. Cannot be selected with some source formats.

*5. Available only when using surround speakers.

*6. PCM of 64kHz, 88.2kHz, and 96kHz are processed at 32kHz, 44.1kHz, and 48kHz respectively.

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

DVD

✔

✔

✔

✔

✔

✔

Requires 6.1/7.1 speakers. Not available while Powered Zone 2 is being used.

Requires 7.1 speakers. Not available while Powered Zone 2 is being used.

68



—Continued

Dolby Digital and Dolby Digital Plus Sources

Dolby Digital

Source format

Multichannel 2ch

Mono/

Multiplex

Button

[Movie/TV]

[Music]

[Game]

[Stereo]

Media

Listening Mode

Mono

DolbyDigital

DolbyDigital Plus

Neo:6

Dolby PLII Movie/Dolby PLIIx Movie

*2

DolbyEX

Neo:6 Cinema

MonoMovie

*4

TV Logic

*4

AllChStereo

FullMono

T-D

Direct

Stereo

DolbyDigital


Neo:6

Dolby PLII Music/Dolby PLIIx Music

*2

DolbyEX

Neo:6 Music

Orchestra

*4

Unplugged

*4

Studio-Mix

*4

AllChStereo

FullMono

DolbyDigital


Neo:6

Dolby PLII Game/Dolby PLIIx Game

*2

DolbyEX

AllChStereo

FullMono

T-D

AllChStereo

Stereo

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*3

*3

*3

*3

*3

*3

*3

✔

✔

*3

✔

✔

✔

✔

DVD, DTV, etc.

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*1. If there are no surround back speakers, depending on the input signal, Dolby Digital may be used.




✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

Dolby Digital Plus


Mono/

Multiplex

✔

Blu-ray, HD DVD

✔ ✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*1

*3

*3

*3

*1

*3

*3

*3

*1

*3

*3

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔



Note:

• With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format changes during playback. It is not a malfunction.

69



—Continued

DTS Sources

Source format

Multichannel

DTS, DTS 96/24

2ch

Media

DVD, CD, etc.

Button Listening Mode

Mono

DTS, DTS 96/24

✔

✔

✔

DTS-ES Discrete/Matrix

Neo:6


*2

DolbyEX

✔

*3

✔

*3

✔

*3

✔

[Movie/TV]

Neo:6 Cinema

MonoMovie

*4 *5

TV Logic

*4 *5

AllChStereo

FullMono

T-D

*5

Direct

Stereo

DTS, DTS 96/24

✔

✔

✔

✔

✔

✔

✔

✔


[Music]

Neo:6


*2

DolbyEX

✔

*3

✔

*3

✔

*3

✔

Neo:6 Music

Orchestra

*4 *5

Unplugged

*4 *5

Studio-Mix

*4 *5

AllChStereo

FullMono

DTS, DTS 96/24

✔

✔

✔

✔

✔

✔


[Stereo]

Neo:6


*2

DolbyEX

FullMono

T-D

*5

AllChStereo

Stereo

✔

*3

✔

[Game]

AllChStereo

✔

*3

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*1. If there are no surround back speakers, or Zone 2 is being used, DTS is used.




*5. DTS 96/24 is processed as DTS.

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔



Mono

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

DTS

Discrete/Matrix

DVD, CD, etc.

✔

✔

✔

*1

✔

✔

✔

✔

✔

✔

✔

✔

*1

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*1

70



—Continued

TrueHD Sources

TrueHD

Source format


Mono/

Multiplex

Media

Blu-ray, HD DVD

Button

[Movie/TV]

Listening Mode

Mono

TrueHD

Neo:6


*1

DolbyEX

✔

✔

✔

*2

✔

*2

✔

*2

✔

✔

✔

[Music]

Neo:6 Cinema

AllChStereo

FullMono

Direct

Stereo

TrueHD

Neo:6


*1

DolbyEX

Neo:6 Music

AllChStereo

FullMono

TrueHD

✔

✔

✔

*2

✔

✔

✔

✔

*2

✔

*2

✔

✔

✔

✔

*2

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

[Stereo]

Neo:6


*1

DolbyEX

AllChStereo

FullMono

AllChStereo

Stereo

✔

[Game]

✔

*2

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔



TrueHD 192kHz


Mono/

Multiplex

✔

✔

✔

✔

✔

✔

Blu-ray, HD DVD

✔

✔

✔

✔

✔

✔



Note:


71



—Continued

DTS-HD Sources

Source format

DTS-HD High Resolution


DTS-HD Master Audio

*1

Mono Multichannel 2ch Mono

Media

Blu-ray, HD DVD

Button Listening Mode

Mono


✔

✔

✔ ✔


[Movie/TV]

Neo:6


*2

DolbyEX

✔

*3

✔

*3

✔

*3

✔

Neo:6 Cinema

AllChStereo

FullMono

Direct

Stereo


✔

✔

✔

✔

✔

✔

✔

✔

✔

✔


[Music]

Neo:6


*2

DolbyEX

✔

*3

✔

*3

✔

*3

✔

Neo:6 Music

AllChStereo

FullMono

✔

✔

✔

✔

✔

✔



[Game]

[Stereo]

Neo:6


*2

DolbyEX

AllChStereo

FullMono

AllChStereo

Stereo

✔

*3

✔

*3

✔

✔

✔

✔

✔

✔

✔

✔

✔

*1. 192kHz DTS-HD Master Audio sources are processed at 96kHz.



✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*3

✔

*3

✔

✔

✔

✔

✔

✔

*3

✔

*3

✔

*3

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

Blu-ray, HD DVD

*3

*3

*3

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔



Note:


72



—Continued

DTS Express and DSD Sources

DTS Express

Source format


Button

[Movie/TV]

[Music]

[Game]

[Stereo]

Media

Listening Mode

Mono

DTS Express

DSD

Neo:6


*2

DolbyEX

Neo:6 Cinema

MonoMovie

*4

TV Logic

*4

AllChStereo

FullMono

T-D

Direct

Stereo

DTS Express

DSD

Neo:6


*2

DolbyEX

Neo:6 Music

Orchestra

*4

Unplugged

*4

Studio-Mix

*4

AllChStereo

FullMono

DTS Express

DSD

Neo:6


*2

DolbyEX

AllChStereo

FullMono

T-D

AllChStereo

Stereo

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*3

*3

*3

*3

*3

*3

Blu-ray, HD DVD

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

*1. DSD signals are processed after conversion to PCM.




Mono

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

Hint!

If you can select PCM or DSD output on your SACD player, in some cases, selecting PCM will provide the best sound quality.

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

DSD

*1

Multichannel

(3/2.1)

SACD

✔

2ch

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

Note:


73



—Continued

74

About the Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.

The illustration shows which speakers are active in each listening mode with 7.1 channel speaker system.

Front left Center Front right

Subwoofer

Surround left Surround back left/ right

Surround right

Direct

In this mode, audio from the input source is output directly with minimal processing, providing high-fidelity reproduction. All of the source’s audio channels are output as they are.

Stereo

Sound is output by the front left and right speakers and subwoofer.

Mono

Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke

DVDs.

Dolby Pro Logic IIx

Dolby Pro Logic II

Dolby Pro Logic IIx

expands any 2-channel source for

7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging. If you’re not using any surround back speakers,

Dolby Pro Logic II

will be used instead of

Dolby Pro Logic IIx.

• Dolby PLIIx Movie

Use this mode with any stereo or Dolby Surround

(Pro Logic) movie (e.g., TV, DVD, VHS).

• Dolby PLIIx Music

Use this mode with any stereo or Dolby Surround

(Pro Logic) music source (e.g., CD, radio, cassette,

TV, VHS, DVD).

• Dolby PLIIx Game

Use this mode with video games, especially those that bear the Dolby Pro Logic II logo.

Dolby Digital

Use this mode with DVDs that bear the Dolby Digital logo, and Dolby Digital TV broadcasts. This is the most common digital surround-sound format, and it’ll put you right in the middle of the action, just like being in a movie theater or concert hall.

5.1-channel source + Dolby EX

These modes expand 5.1-channel sources for 6.1/7.1channel playback. They’re especially suited to Dolby EX soundtracks that include a matrix-encoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects.

5.1-channel source + Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx Music mode to expand 5.1-channel sources for 6.1/7.1-channel playback.

5.1-channel source + Dolby PLIIx Movie

These modes use the Dolby Pro Logic IIx Movie mode to expand 5.1-channel sources for 7.1-channel playback.

Dolby Digital Plus

Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from Dolby. It supports up to 7.1 channels with 48kHz sampling rate.

Dolby TrueHD

Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc formats, this new Dolby format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate.

For the signals supported by the AV receiver, see page 71.

DTS

The DTS digital surround-sound format supports up to

5.1 discrete channels and uses less compression for highfidelity reproduction. Use it with DVDs and CDs that bear the DTS logo.

DTS 96/24

This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96kHz sampling rate and 24bit resolution, providing superior fidelity. Use it with

DVDs that bear the DTS 96/24 logo.

DTS-ES Discrete

This mode is for use with DTS-ES Discrete soundtracks, that use a discrete surround back channel for true

6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Discrete soundtrack.



—Continued

DTS-ES Matrix

This mode is for use with DTS-ES Matrix soundtracks, that use a matrix-encoded back-channel for 6.1/7.1channel playback. Use it with DVDs that bear the DTS-

ES logo, especially those with a DTS-ES Matrix soundtrack.

DTS Neo:6

This mode expands any 2-channel source for 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

• Neo:6 Cinema

Use this mode with any stereo movie (e.g., TV,

DVD, VHS).

• Neo:6 Music

Use this mode with any stereo music source (e.g.,

CD, radio, cassette, TV, VHS, DVD).

5.1-channel source + Neo:6

This mode uses Neo:6 to expand 5.1-channel sources for

6.1/7.1-channel playback.

DTS-HD High Resolution Audio

Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from DTS. It supports up to 7.1 channels with 96 kHz sampling rate.


Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc formats, this new DTS format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate.

For the signals supported by the AV receiver, see

page 72.

DTS Express

This format supports up to 5.1 channels and a lower sampling rate of 48 kHz. Applications include interactive audio and commentary encoding for HD DVD Sub

Audio and Blu-ray Secondary Audio. Also broadcast and media servers.

DSD

DSD stands for Direct Stream Digital and is the format used to store digital audio on Super Audio CDs (SACD).

This mode can be used with SACDs that feature multichannel audio.

Onkyo Original DSP Modes

Mono Movie

This mode is suitable for old movies and other mono sources. The center speaker outputs the sound as it is, while reverb is applied to the sound output by the other speakers, giving presence to even mono material.

Orchestra

Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image and simulates the natural reverberation of a large hall.

Unplugged

Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.

Studio-Mix

Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

TV Logic

This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices.

All Ch Stereo

Ideal for background music, this mode fills the entire listening area with stereo sound from the front, surround, and surround back speakers.

Full Mono

In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room.

T-D (Theater-Dimensional) or

With this mode you can enjoy a virtual 5.1 surround sound even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

75


Recording

This section explains how to record the input source and how to record audio and video from separate sources.

Notes:

• The surround sound and DSP listening modes cannot be recorded.

• Copy-protected DVDs cannot be recorded.

• Sources connected to the analog multichannel input cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

Recording the Input Source

Audio sources can be recorded to a recorder (e.g., cassette deck, CDR, MD) connected to the TAPE OUT jack.

Video sources can be recorded to a video recorder (e.g.,

VCR, DVR) connected to the VCR/DVR OUT jacks.

See pages 21 to 37 for hookup information.

1

Use the input selector buttons to select the source that you want to record.

See “Which Connections Should I

Use?” on page 22 to see which signals

can be output and recorded.


You can watch the source while recording it. The AV receiver’s Master Volume control has no effect on recording.

Recording from Different AV Sources

You can overdub audio onto your video recordings by simultaneously recording audio and video from two separate sources. This is possible because only the audio source is switched when an audio-only input source, such as Tape, Tuner, or CD, is selected, the video source remains the same.

In the following example, audio from the CD player connected to the CD IN and video from the camcorder connected to the AUX Input Video jack are recorded by the

VCR connected to the VCR/DVR OUT jacks.

Camcorder video signal audio signal

SIRIUS

AM

ANTENNA

FM

75

CD player

VCR

2

3

On your recorder, start recording.

On the source component, start playback.

Note:

• If you select a different input source during recording, that input source will be recorded instead.

1

Prepare the camcorder and CD player for playback.

2

Prepare the VCR for recording.

3

Press the [AUX] input selector button.

4

Press the [CD] input selector button.

This selects the CD player as the audio source but leaves the camcorder as the video source.

5

Start recording on the VCR, then start playback on the camcorder and CD player.

Video from the camcorder and audio from the CD player are recorded by the VCR.

76


Adjusting the Listening Modes

Using the Audio Adjust Settings

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

1



[Setup] button.



2

Use the Up and Down [ ]/[ ] buttons to select “3. Audio

Adjust,” and then press [Enter].

The Audio Adjust settings are explained below.

Multiplex/Mono Settings

Multiplex

■

Input Ch

This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

Main:

Sub:

Main/Sub:

The main channel is output (default).

The sub channel is output.

Both the main and sub channels are output.

Mono

■

Input Ch

This setting determines which channel is output when the Mono listening mode is used with a stereo source.

Left+Right:

Both the left and right channels are output

(default).

Left:

Right:

Only the left channel is output.

Only the right channel is output.

3

Use the Up and Down [ ]/[ ] buttons to select an item, and then press [Enter].

3. Audio Adjust

1. Multiplex/Mono

2. PL II x/Neo:6

3. Dolby EX

4. Theater-Dimensional

4

Use the Up and Down [ ]/[ ] buttons to select an option, and use the Left and Right [ ]/[ ] buttons to change it.

The Audio Adjust menu items are explained below.

PLIIx/Neo:6 Settings

PLIIx Music (2 ch Input)

These settings apply to only 2-channel stereo sources.

If you’re not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro

Logic IIx.

■

Panorama

With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.

On:

Off:

Panorama function on.

Panorama function off (default).

■

Dimension

With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. It can be adjusted from –3 to +3. The default value is 0. Higher settings move the sound field backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

5


[Setup] button.

Setup closes.

77



—Continued

■

Center Width

With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic

IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output by only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. It can be adjusted from 0 to 7. The default value is 3.

Neo:6 Music

■

Center Image

The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. It can be adjusted from 0 to 5. The default value is 2.

When set to 0, the front left and right channel output is attenuated by half (–6 dB), giving the impression that the sound is located centrally. This setting works well when the listening position is considerably off center. When set to 5, the front left and right channels are not attenuated, maintaining the original stereo balance.

Dolby EX Settings

■

Dolby EX

This setting determines how Dolby EX signals are handled.

Auto:

When the source is Dolby EX, you can select the Dolby EX listening mode.

Manual:

When the source is Dolby EX, you can select any of the listening modes compatible with this format (e.g., Dolby EX, Dolby Pro Logic IIx, etc.).

Theater-Dimensional Setting

■

Listening Angle

With this setting, you can optimize the Theater-Dimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position.

Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Front left speaker Front right speaker

20˚/40˚

Narrow:

Select if the listening angle is 20 degrees.

Wide:

Select if the listening angle is 40 degrees

(default).

78



—Continued

Using the Audio Settings

You can change various audio settings by pressing the

[Audio] button.

Note:

• When the Audio TV Out setting is set to On (page 91), the [AUDIO] button is disabled.

1

2

3

Press the [Receiver] button followed by the [Audio] button.

Use the Up and Down [ ]/[ ] buttons to select an item.

Use the Left and Right [ ]/[ ] buttons to change the setting.

Repeat this step for the other settings.

Late Night Function

■

Late Night

With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

For

Dolby Digital and Dolby Digital Plus

sources, the options are:

Off:

Late Night function off (default).

Low:

Small reduction in dynamic range.

High:

Large reduction in dynamic range.

For

Dolby TrueHD

sources, the options are:

Auto:

The Late Night function is set to On or Off automatically (default).

Off:

On:

Late Night function off.

Late Night function on.

Notes:

• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or

Dolby TrueHD.

• The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options.

• The Late Night function is set to Off when the AV receiver is set to Standby. For Dolby TrueHD sources, it will be set to Auto.

The Audio Adjust settings are explained below.

Tone Control Settings

You can adjust the bass and treble for the front speakers, except when the Direct listening mode is selected.

■

Front Bass

You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.

■

Front Treble

You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.

Notes:

• To bypass the bass and treble tone circuits, select the

Direct listening mode.

• This procedure can also be performed on the AV receiver by using its [TONE], [–], and [+] buttons.

CinemaFILTER

■

Cinema Fltr

With the CinemaFILTER, you can soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater.

CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Pro

Logic IIx Movie, Dolby Pro Logic II Movie, DTS, DTS-

ES, DTS Neo:6 Cinema, DTS 96/24, and Neo:6.

Off:

On:

CinemaFILTER off.

CinemaFILTER on.

Note:

• The CinemaFILTER may not work when used with certain input sources.

79



—Continued

Audyssey Dynamic EQ

■

DynamicEQ

With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics.

It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level--not just at reference level.

Off:

On:

Audyssey Dynamic EQ off.

Audyssey Dynamic EQ on.

Note:

• Audyssey Dynamic EQ can be set only when the

Equalizer Settings on page 86 are set to Audyssey.

Speaker Levels

You can adjust the volume of each speaker while listening to an input source.

These temporary adjustments are cancelled when the AV receiver is set to Standby.

■

Subwoofer

You can adjust the level from –15 dB to +12 dB.

■

Center

You can adjust the level from –12 dB to +12 dB.

Notes:

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to No or None in the Speaker

Configuration cannot be adjusted (see page 82).

• This setting is not available when the Direct listening mode is used with an analog input signal.

Music Optimizer

■

M.Optimizer

The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3.

Off:

On:

Music Optimizer off (default).

Music Optimizer on.

Note:

• The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below

48kHz and analog audio input signals. The Music

Optimizer is disabled when the Direct listening mode is selected.

A/V Sync

■

A/V Sync

When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync.

With this setting, you can correct this by delaying the audio signals. You can set it from 0 to 100 milliseconds

(ms) in 5 millisecond steps.

80



—Continued

Listening Mode Presets

On the Listening Mode Preset menu, you can specify a default listening mode for each of the audio formats supported by each input selector. The AV receiver will then select the listening mode automatically depending on the format of the input signal. You can still select the other listening modes, although the default listening mode will be used the next time you turn on the AV receiver.

4

1



[Setup] button.



2

Use the Up and Down [ ]/[ ] buttons to select “5. Listening

Mode Preset,” and then press

[Enter].

3

Use the Up and Down [ ]/[ ] buttons to select an input selector, and then press [Enter].

The audio formats supported by that input selector appear.

For the Tuner input selector, Analog is the only format available.

5

Use the Up and Down [ ]/[ ] buttons to select an audio format, and use the Left and Right

[ ]/[ ] buttons to select a listening mode.

Only listening modes compatible with the audio format can be selected (see

pages 68–73).

Analog/PCM:

Specifies the default listening mode for analog and PCM sources.

Dolby Digital:

Specifies the default listening mode for Dolby Digital sources.

DTS:

Specifies the default listening mode for DTS sources.

D.F. 2ch:

Specifies the default listening mode for 2-channel (2/0) stereo sources in a digital format, such as Dolby Digital or DTS.

D.F. Mono:

Specifies the default listening mode for mono sources in a digital format, such as Dolby Digital or DTS.

Multich PCM:

Specifies the default listening mode for multichannel PCM sources, such as DVD-Audio (input via

HDMI).

192k/176.4k:

Specifies the default listening mode for high resolution

192kHz and 176.4kHz digital sources, such as DVD-Audio.

Dolby TrueHD:

Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD

(input via HDMI).

DTS-HD Master Audio:

Specifies the default listening mode for DTS-HD

Master Audio sources, such as Blu-ray or HD DVD (input via HDMI).

DSD:

Specifies the default listening mode for DSD multichannel sources, such as SACD.


[Setup] button.

Setup closes.

Note:


81


Advanced Setup

Speaker Setup

This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the automatic speaker setup.

Some of the speaker settings are set automatically by the

Automatic Speaker Setup function (see page 39).

Speaker Configuration

This setting is set automatically by the Automatic

Speaker Setup function (see page 39).

With the Speaker Configuration settings, you can specify which speakers are connected and a crossover frequency, distance, and level for each speaker.

The following crossover frequencies can be specified:

Full Band, 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz,

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, or 200Hz.

Specify Full Band for speakers that can output low-frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will then be output by the subwoofer instead of the speaker. Refer to your speakers’ manuals to determine the optimum crossover frequencies.

1

Press the [Receiver] button followed by the [Setup] button.



3

4

5

6

2


Setup,” and then press the

[Enter] button.


Configuration,” and then press the [Enter] button.

While the “Subwoofer” setting is selected, use the Left and Right

[ ]/[ ] buttons to select Yes or

No .

Yes:

Select if a subwoofer is connected.

No:

Select if no subwoofer is connected.

Use the Down [ ] button to select “Front,” and then use the

Left and Right [ ]/[ ] buttons to select a crossover frequency.

Note:

• Fixed at Full Band if Subwoofer

(step 4) is set to No.

Use the Down [ ] button to select “Center,” and then use the


If no center speaker is connected, select

None.

Note:

• Cannot select Full Band if Front

(step 5) is set to anything other than

Full Band.

82


Advanced Setup

—Continued

7

Use the Down [ ] button to select “Surround,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency.

If no surround left and right speakers are connected, select None.

Note:

• Cannot select Full Band if Front


Full Band.

8

9

Use the Down [ ] button to select “Surr Back,” and use the


If no surround back speakers are connected, select None.

Notes:

• If the Surround setting in step 7 is set

to None, or Powered Zone 2 is being used, this setting does not appear.

• Cannot select Full Band if Surround


Full Band.

Use the Down [ ] button to select “Surr Back Ch,” and use the Left and Right [ ]/[ ] buttons to select 2ch or 1ch .

2ch:

Select if two (left and right) surround back speakers are connected.

1ch:

Select if one surround back speaker is connected.

Note:

• If the Surround or SurrBack settings in steps 7 and 8 are set to None, this setting does not appear.

Continue with step 10 of the “Low-Pass

Filter for the LFE Channel” setting.

Note:

• These settings cannot be changed while headphones are connected or the multichannel DVD input is being used.

Low-Pass Filter for the LFE Channel

This setting is not set automatically by the Automatic


With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

10

Use the Down [ ] button to select “LPF of LFE,” and then use the Left and Right [ ]/[ ] buttons to select a lowpass filter frequency.

The following low-pass filter frequencies can be selected: 80Hz, 90Hz,

100Hz, or 120Hz.

Continue with step 11 of the “Double

Bass” setting on the next page.

83


Advanced Setup

—Continued

Double Bass

This setting is not set automatically by the Automatic


With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. This function can be

set only if the Subwoofer setting (step 3) is set to Yes,

and the Front setting (step 4) is set to Full Band in the

Speaker Configuration on page 82.

11

Use the Down [ ] button to select “Double Bass,” and then use the Left and Right [ ]/[ ] buttons to select:

On:

Double Bass function on.

Bass from the front left and right channels is also fed to the subwoofer (default).

Off:

Double Bass function off.

Speaker Distance

These settings are set automatically by the Automatic


With these settings, you can specify the distance from each speaker to the listening position.

1

Measure and make a note of the distance from each speaker to the listening position.

2



[Setup] button.



3



[Enter] button.

12


Setup closes.

Note:

• These settings cannot be changed while headphones are connected or the multichannel DVD input is being used.

4

Use the Up and Down [ ]/[ ] buttons to select “3. Speaker Distance,” and then press [Enter].

5

While “Unit” is displayed, use the

Left and Right [ ]/[ ] buttons to select “feet” or “meters”.

feet: meters:

Distances can be set in feet.

Range: 1 to 30 feet in 0.5-foot steps.

Distances can be set in meters. Range: 0.3 to 9 meters in 0.15-meter steps.

84


Advanced Setup

—Continued

6

7

8

Use the Down [ ] button to select “Left”, and use the Left and Right [ ]/[ ] buttons to specify the distance for the front speakers, then press the Down

[ ] button to select the next speaker.

Repeat step 6 for all speakers.

Note:

• Speakers that you set to No or None in the Speaker Configuration

(page 82) cannot be selected.


Setup closes.

2

3

Notes:

• The Center and Subwoofer distances can be set up to

5 ft. (1.5 m) more or less than the Left distance. For example, if the Left distance is set to 20 ft. (6 m), the

Center and Subwoofer distances can be set between 15 and 25 ft. (4.5 and 7.5 m).

• The Surround and Surround Back distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the

Left distance. For example, if the Left distance is set to 20 ft. (6 m), the SurrRight, Surr Left, Surr Back R, and Surr Back L distances can be set between 5 and 25 ft. (1.5 and 7.5 m).

• The speaker distance cannot be adjusted while a pair of headphones is connected or the multichannel DVD input is being used.

Speaker Levels



You can set the volume level of each speaker so that all speakers can be heard equally at the listening position.

Note:

• The speaker levels cannot be adjusted while a pair of headphones is connected or the AV receiver is muted.

1



[Setup] button.



4

5

6

7



[Enter] button.

Use the Up and Down [ ]/[ ] buttons to select “4. Level Calibration,” and then press [Enter].

A pink noise test tone is output by the front left speaker.

Turn up the volume so that you can hear the test tone sufficiently.

As each speaker outputs the test tone, its name appears on the display.

Use the Left and Right [ ]/[ ] buttons to adjust the speaker level, and use the Down [ ] button to select the next speaker.

The levels can be adjusted from –12 to

+12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).

Repeat step 5 so that the level of the test tone coming from each speaker is the same.

Speakers that you set to No or None in the Speaker Configuration (page 82) do not output the test tone.


Setup closes.

Don’t forget to turn down the volume if you turned it up while setting the levels.

85


Advanced Setup

—Continued

Equalizer Settings



Here you can adjust the tone of individual speakers. To

set the volume of individual speakers, see page 85.

1



[Setup] button.



2



[Enter] button.

5

6

3

Use the Up and Down [ ]/[ ] buttons to select “5. Equalizer

Settings,” and then press [Enter].

7

Press the Down [ ] button, and then use the Left and Right

[ ]/[ ] buttons to select a speaker.

2–5. Equalizer Settings

Equalizer Manual

Channel Front

63Hz 0dB

250Hz 0dB

1000Hz 0dB

4000Hz 0dB

16000Hz 0dB

Use the Up and Down [ ]/[ ] buttons to select a frequency.

Use the Left and Right [ ]/[ ] buttons to adjust the level at that frequency.

The volume at each frequency can be adjusted from –6 to +6 dB in 1 dB steps.

Tip:

Low frequencies (e.g., 63Hz) affect bass sounds; high frequencies

(e.g., 16000Hz) affect treble sounds.

Use the Up [ ] button to select

“Channel,” and then use the Left and Right [ ]/[ ] buttons to select another speaker.

Repeat steps 5 and 6 for each speaker.

Speakers that you’ve set to No or None in the Speaker Configuration (page 82) cannot be selected.

86

4


Off:

Tone off, response flat.

Audyssey:

The tone for each speaker is set automatically by the

Automatic Speaker Setup function. Be sure to select this setting after having performed the Automatic

Speaker Setup.

Manual:

You can adjust the equalizer for each speaker manually.

If you selected Manual, continue with this procedure. If you selected Off or

Audyssey, go to step 8.

8


The setup menu closes.

Notes:

• The front, center, surround, and surround back speakers can be adjusted at 63Hz, 250Hz, 1000Hz, 4000Hz, and 16000Hz. The subwoofer can be adjusted at 25Hz,

40Hz, 63Hz, 100Hz, and 160Hz.

• While the Direct listening mode is selected, the equalizer settings have no effect.



Advanced Setup

—Continued

Source Setup

This section explains items on the Source Setup menu.

Items can be set individually for each input selector.

1

Press the input selector buttons to select an input source, and then press the [Receiver] Remote

Mode button.

2

3

4

6


[Setup] button.

Setup closes.




Use the Up and Down [ ]/[ ] buttons to select “4. Source



IntelliVolume

With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others.

Use the Left and Right [ ]/[ ] buttons to set the level.

If a component is noticeably louder than the others, use the Left [ ] button to reduce its input level. If it’s noticeably quieter, use the Right [ ] button to increase its input level. The input level can be adjusted from

–12 dB to +12 dB in 1 dB steps.

Note:

• IntelliVolume does not apply for Zone 2.

A/V Sync

When using your DVD player’s progressive scanning function, you may find that the picture and sound are out of sync. With the A/V Sync setting, you can correct this by applying a delay to the audio signal. The delay can be set from 0 to 100 milliseconds (msec) in 5 millisecond steps.

Use the Left and Right [ ]/[ ] buttons to set the delay.

To view the TV picture while setting the delay, press

[Enter].

If HDMI Lip Sync is enabled (see page 91), and your TV or display supports HDMI Lip Sync, the displayed delay time will be the A/V Sync delay time. The HDMI Lip

Sync delay time is displayed underneath in parentheses.

Note:

• A/V Sync is disabled when the Direct listening mode is used with an analog input source.

5

Use the Left and Right [ ]/[ ] buttons to change it.

The Source Setup menu items are explained below.

87


88

Advanced Setup

—Continued

Miscellaneous Setup

This section explains items on the Miscellaneous menu.

1



[Setup] button.



2

3

4

5

Use the Up and Down [ ]/[ ] buttons to select

“6. Miscellaneous,” and then press [Enter].


Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it.

The items are explained below.


[Setup] button.

Setup closes.

Note:


Volume Setup

■

Maximum Volume

With this setting, you can limit the maximum volume.

The Maximum Volume range is Off, 79 to 30.

■

Power On Volume

This setting determines what the volume will be each time the AV receiver is turned on.

The range is Last, Min, 1 to 79, Max.

To use the same volume level as when the AV receiver was last turned off, select Last.

Note:

• The Power On Volume setting cannot be set higher than the Maximum Volume setting.

■

Headphone Level

With this setting, you can offset the headphone volume relative to the main volume. This is useful if your headphones are too loud or too quiet at the volume setting you usually use when listening through your speakers. The headphone level can be set from –12 dB to +12 dB.

■

Zone 2 Maximum Volume

With this setting, you can limit the maximum volume for

Zone 2.

The Maximum Volume range is Off, 79 to 30.

■

Zone 2 Power On Volume

This setting determines what the volume will be for Zone

2 each time the AV receiver is turned on.

The range is Last, Min, 1 to 79, Max.

To use the same volume level as when the AV receiver was last turned off, select Last.

OSD Setup

■

Immediate Display

This setting determines whether operation details are displayed onscreen immediately after an AV receiver function is used.

On:

Off:

Displayed (default).

Not displayed.

Even if On is selected, operation details are not output if the input source is connected to a COMPONENT

VIDEO IN or HDMI IN.

■

Monitor Type

With this setting, you can specify the aspect ratio of your

TV so that menus are displayed properly.

16:9:

4:3:

Select if your TV is 16:9 (default).

Select if your TV is 4:3.

■

Display Position

This setting determines where on the screen operation details are displayed.

Bottom:

Bottom of the screen (default).

Top:

Top of the screen.

■

TV format (not North American model)

For the onscreen setup menus to display properly, you must specify the TV system used in your area.

Auto:

NTSC:

PAL:

Select this to have the AV receiver automatically detect the TV system from the video input signals.

Select if the TV system in your area is NTSC.

Select if the TV system in your area is PAL.


Advanced Setup

—Continued

Hardware Setup

This section explains items on the Hardware menu.

Remote indicator

Receiver

3


The screen for that item appears.

1

2

Eenter

Setup

Number buttons

4

5

Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it.

The items are explained below.


[Setup] button.

Setup closes.



[Setup] button.





Note:


Remote Control

■

Remote ID

When several Integra/Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from 1, the default, to 2 or

3.

Note:

• If you do change the AV receiver’s remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

Changing the Remote Controller’s ID

1

While holding down the

[Receiver] Remote Mode button, press and hold down the [Setup] button until the Remote indicator lights up (about 3 seconds).

(3 seconds)

89


Advanced Setup

—Continued

2

Use the number buttons to enter

ID 1, 2, or 3.

The Remote indicator flashes twice.

Zone 2

See “Zone 2” on page 93.

90

Tuner

■

AM Frequency (on some models)

See “AM Frequency Step Setup (on some models)” on page 52.

■

SAT Radio Mode (on North American model)

If you connect a SIRIUS Satellite Radio antenna to the

AV receiver, set this setting to SIRIUS. Otherwise, select

None. See the separate Satellite Radio Guide for more information.

■

Antenna Aiming (on North American model)

The ID of the Sirius Connect Home Tuner is displayed here. You must sign up to obtain a SIRIUS ID. See the separate Satellite Radio Guide for more information.

■


(on North American model)

This item is for use with SIRIUS Satellite Radio. It’s not available if SAT Radio Mode is set to None. See the separate Satellite Radio Guide for more information.

Analog Multich

■

Subwoofer Input Sensitivity

Some DVD players output the LFE channel from their analog subwoofer output at 15 dB higher than normal.

With this setting, you can change the AV receiver’s subwoofer sensitivity to match your DVD player. Note that this setting only affects signals connected to the AV receiver’s MULTI CH SUBWOOFER jack.

You can select 0dB, 5dB, 10dB, or 15dB.

If you find that your subwoofer is too loud, try the 10 dB or 15 dB setting.

HDMI

■

Output Resolution

You can specify the output resolution for the HDMI outputs and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV.

See the “Video Resolution Chart” on page 114 to see

how the AV receiver handles video input at different resolutions.

Through:

Select this to pass video through the AV receiver at the same resolution. However, if your TV doesn’t support the resolution, the AV receiver will automatically convert the resolution as necessary.

Auto:

480p (480p/576p):

Select this for 480p or 576p output and video conversion as necessary.

720p:

Select this to allow the AV receiver to automatically convert the video to the highest resolution supported by your TV.

1080i:

Select this for 720p output and video conversion as necessary.

Select this for 1080i output and video conversion as necessary.

■

Zoom Mode

This setting determines the aspect ratio that will be used for 480i, 480p, 576i, and 576p input signals when they are output by the HDMI OUT. This setting only applies when the HDMI Output Resolution setting is set to 1080i or 720p.

Normal:

Full:


Advanced Setup

—Continued

■

Audio TV Out

This setting determines whether audio received by an

HDMI input is output by the HDMI outputs. You may want to change this setting to On if your TV is connected to an HDMI output and you want to listen to audio from an HDMI component through your TV’s speakers. Normally, it should be set to Off.

Off:

On:

HDMI audio is not output (default).

HDMI audio is output.

Notes:

• If On is selected and the signal can be output by the

TV, the AV receiver will output no sound through its speakers.

• When TV Control is enabled, this setting is set to

Auto.

• With some TVs and input signals, no sound may be output even if On is selected.

• When the Audio TV Out setting is set to On, or TV

Control is set to Enable and you’re listening through

your TV’s speakers (see page 32), if you turn up the

AV receiver’s volume control, the sound will be output by the AV receiver’s speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

■

Lip Sync

The Lip Sync function can automatically synchronize

HDMI audio and video that’s gotten out of sync due to the complex digital video processing being performed by your HDMI-compatible TV. With HDMI Lip Sync, the audio delay required to synchronize the audio and video is calculated and applied automatically by the AV receiver.

Disable:

HDMI lip sync disabled.

Enable:

HDMI lip sync enabled.

Notes:

• This function works only if your HDMI-compatible

TV supports HDMI Lip Sync.

• You can check the amount of delay being applied by the HDMI Lip Sync function on the A/V Sync screen

(see page 87).

■

x.v.Color

If your HDMI source and HDMI-compatible TV both support the “x.v.Color,” you can enable “x.v.Color” on the AV receiver with this setting.

Disable:

“x.v.Color” disabled.

Enable:

“x.v.Color” enabled.

■

Control

This function allows RIHD-compatible components connected via HDMI to be controlled with the AV receiver.

Disable:

Enable:

RIHD disabled.

RIHD enabled.

Notes:

• RIHD, which stands for Remote Interactive over

HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than RIHD-compatible components and recommended components cannot be guaranteed.

• Select Disable if a connected component is incompatible or you’re not sure about its compatibility.

• If operation is unreliable when set to Enable, select

Disable instead.

Power Control

To link the power functions of RIHD-compatible components connected via HDMI, select Enable.

Disable:

Power Control disabled.

Enable:

Power Control enabled.

Notes:

• The Power Control setting can be set only when the above Control setting is set to Enable.

• HDMI power control only works with RIHD-compatible components that support it and may not work properly with some components due to their settings or compatibility.

• When set to Enable, the AV receiver consumes more power.

• When set to Enable, the AV receiver enters Ready mode when set to Standby, and the Standby indicator lights up.

• When set to Enable, regardless of whether the AV receiver is On or on Standby, both audio and video received by an HDMI input will be output by the

HDMI OUT for playback on the TV or other component that’s connected to the HDMI OUT.

91


Advanced Setup

—Continued

TV Control

Select Enable to control the AV receiver from an RIHDcompatible TV connected via HDMI.

Disable:

TV Control disabled.

Enable:

TV Control enabled.

Notes:

• Select Disable if your TV is incompatible or you’re not sure about its compatibility.

• The TV Control setting can be set only when the above

Control and Power Control settings are both set to

Enable.

• When the Audio TV Out setting is set to On, or TV

Control is set to Enable and you’re listening through

your TV’s speakers (see page 32), if you turn up the

AV receiver’s volume control, the sound will be output by the AV receiver’s speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

Note:

• After changing the Control, Power Control, or TV

Control setting, be sure to turn all of your components off and then back on again. Refer to the instruction manuals for your other components.

Lock Setup

With this setting, you can protect your settings by locking the setup menus.

1




2

3

Use the Up and Down [ ]/[ ] buttons to select “8. Lock Setup,” and then press [Enter].

Network

These setting are for use with home automation equipment and external controllers.


Locked:

Unlocked:

Setup menus locked.

Setup menus unlocked.

When Locked is selected, only this

Lock Setup item can be accessed.

4


Setup closes.

92


Zone 2

In addition to your main listening room, you can also enjoy playback in the other room, or as we call Zone 2. And, you can select a different source for each room.

Connecting Zone 2

There are two ways you can connect Zone 2 speakers:

1. Connect them directly to the AV receiver.

2. Connect them to an amp in Zone 2.

Connecting Your Zone 2 Speakers Directly to the AV receiver

This setup allows 5.1-channel playback in your main room and 2-channel stereo playback in Zone 2, with a different source in each room. This is called Powered

Zone 2, as the Zone 2 speakers are powered by the AV receiver. Note that when Powered Zone 2 is turned off, you can enjoy 7.1-channel playback in your main room.

Connecting Your Zone 2 Speakers to an

Amp in Zone 2

This setup allows 7.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2, with a different source in each room.

Hookup

• Use an RCA audio cable to connect the AV receiver’s

ZONE 2 PRE OUT L/R jacks to an analog audio input on your Zone 2 amp.

• Connect your Zone 2 speakers to the speaker terminals on your Zone 2 amp.

Main room

To use this setup, you must set the Powered Zone 2

setting to Act (see page 94).

TV

Hookup

• Connect your Zone 2 speakers to the AV receiver’s

ZONE 2 SPEAKERS L/R speaker terminals.

AV receiver

ZONE 2

PRE OUT

L

R

TV

Zone 2

L

AV receiver

ZONE 2 SPEAKERS

L

R

R

Zone 2

R L

IN

Receiver/ integrated amp

Notes:

• The Zone 2 volume must be set on the Zone 2 amp.

• If you’re using a power amp with no volume control in

Zone 2, you must set the Zone 2 Out setting to Variable

(see page 95).

Notes:

• With this setup, the Zone 2 volume is controlled by the

AV receiver.

• Powered Zone 2 cannot be used if Speaker Type is set

to Bi-Amp (see page 43).

93


Zone 2

—Continued

Powered Zone 2 Setting

If you’ve connected your Zone 2 speakers to the AV

receiver, as explained in “Connecting Your Zone 2

Speakers Directly to the AV receiver” on page 93, you

must set the Powered Zone 2 setting to Act (Activated).

3

Use the Up and Down [ ]/[ ] buttons to select “2. Zone2,” and then press [Enter].

Receiver

4


7–2. Zone2

Powered Zone2 Not Act

Zone2 Fixed

Enter

Setup

1

2

5

Not Act:

ZONE 2 SPEAKERS L/R speaker terminals not activated (Powered Zone 2 disabled).

Act:

ZONE 2 SPEAKERS L/R speaker terminals activated

(Powered Zone 2 enabled).


Setup closes.



[Setup] button.



Use the Up and Down [ ]/[ ] buttons to select “7. Hardware-


Notes:

• When Act is selected and Zone 2 turned on, the Zone 2 speakers connected to the ZONE 2 L/R speaker terminals output sound, but the surround back speakers connected to the SURR BACK L/R speaker terminals do not. When Act is selected and Zone 2 turned off, the surround back speakers output sound as normal.

• Powered Zone 2 cannot be used if Speaker Type is set to Bi-Amp.


94


Zone 2

—Continued

Zone2

Receiver

3

Input

Selector

Enter

Setup

4

Use the Up and Down [ ]/[ ] buttons to select “2. Zone 2,” and then press [Enter].

The Zone 2 screen appears.

7–2. Zone2

Powered Zone2

Zone2 Out

Not Act

Fixed

Use the Up and Down [ ]/[ ] buttons to select “Zone 2 Out,” and use the Left and Right


Fixed:

The Zone 2 volume must be set on the amp in that zone.

Variable:

The Zone 2 volume can be set on the AV receiver.

Zone 2 Out Settings

If you’ve connected your Zone 2 speakers to an amp with no volume control, set the Zone 2 Out setting, to

Variable so that you can set the zone’s volume, balance, and tone on the AV receiver.

1



[Setup] button.


5


Setup closes.

Note:


2




95


Zone 2

—Continued

Using Zone 2

This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2.

Controlling Zone 2 from the AV receiver

Zone 2

Off Tone

Notes:

• Only analog input sources are output by Zone 2. Digital input sources are not output. If no sound is heard when an input source is selected, check to make sure it’s connected to an analog input.

• While Zone 2 is on, the Auto Power On/Standby and

Direct Change functions do not work.

• While Powered Zone 2 is being used, listening modes that require surround back speakers (6.1/7.1), such as

Dolby Digital EX and DTS-ES are unavailable.

+, –

Zone 2 Level

Controlling Zone 2 with the Remote

Controller

Zone2 On/Standby

Input

Selector

Muting

VOL /

1

2

To turn on Zone 2 and select an input source, press the [Zone 2] button repeatedly.

Alternatively, press the [Zone 2] button followed by an input selector button within 8 seconds.

Zone 2 turns on and ZONE 2 indicator lights up.

To select the same source as that of the main room, press the [Zone 2] button repeatedly until “Z2 Sel: Source” appears.

To select AM or FM press the [Tuner]

Input Selector button repeatedly. On the

North American model, you can also select SIRIUS.

Note:

• You cannot select different AM or

FM radio stations for your main room, Zone 2. The same AM/FM radio station will be heard in each room.

To turn off Zone 2, press the

Zone 2 [Off] button.

1

2

Press the [Zone 2] button, then point the remote controller at the

AV receiver and press the

[On/Standby] button.

Zone 2 turns on and ZONE 2 indicator lights up.

To select an input source for

Zone 2, press the [Zone 2] button, followed by an Input Selector button.

To select AM or FM press the [Tuner]

Input Selector button repeatedly. On the North American model, you can also select SIRIUS.

Note:

• You cannot select different AM or FM radio stations for your main room,

Zone 2. The same AM/FM radio station will be heard in each room.

96


Zone 2

—Continued

3

To turn off Zone 2, press the

[Zone 2] button, followed by the

[On/Standby] button.

3

Use the Tone Plus [+] and Minus

[–] buttons to adjust the balance.

You can adjust the balance from 0 in the center to +10 to the right or +10 to the left in 2 steps.

Note:

• To control Zone 2, you must press the remote controller’s [Zone 2] button first.

Adjusting the Volume of Zone 2


On the remote controller, press the [Zone 2] Remote Mode button, and then use the VOL

[ ]/[ ] buttons.

Muting Zone 2

On the remote controller, press the [Zone 2] Remote Mode button, and then press the [Muting] button.

To unmute a zone, on the remote controller, press the [Zone 2]

Remote Mode button, and then press the [Muting] button again.

Adjusting the Tone of Zone 2

1

AV receiver


[Zone 2] button.

AV receiver


[Zone 2] ] button, and then use the Level Up and Down [ ]/[ ] buttons.

2

Press the AV receiver’s [Tone] button repeatedly to select Bass or Treble.

Adjusting the Balance of Zone 2

1

AV receiver


[Zone 2] button.

3

Use the Tone Plus [+] and Minus

[–] buttons to adjust the bass or treble.

You can boost or cut the Bass or Treble from –10 dB to +10 dB in 1 dB steps.

2

Press the AV receiver’s [Tone] button repeatedly to select Balance.

Notes:

• Zone 2 can also be unmuted by adjusting the volume.

• The Zone 2 level, balance, and tone functions have no effect on the ZONE 2 PRE OUT when the Zone 2 Out

setting is set to Fixed (page 95).

97


Zone 2

—Continued

Using the 12V Triggers

The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for the main room or Zone 2.

When triggered, the output from a 12V TRIGGER OUT goes high (+12 volts, 100 milliamperes max).

C

A

12V TRIGGER OUT

B

3

SIRIUS

AM

ANTENNA

FM

75

4

Use the Up and Down [ ]/[ ] buttons to select “12V Trigger A,

B, or C,” and then press [Enter].

The 12V Trigger A/B/C Setup screen appears.

6-x. 12V Trigger x Setup

Delay 1sec

DVD Main/Zone2

VCR/DVR Main/Zone2

CBL/SAT Main/Zone2

GAME/TV Main/Zone2

AUX Main/Zone2

TAPE Main/Zone2

CD Main/Zone2

Use the Up and Down [ ]/[ ] buttons to select “Delay,” and use the Left and Right [ ]/[ ] buttons to select: 0 sec, 1 sec, 2 sec, or 3 sec.

When 0 sec is selected, the trigger signal is output as soon as the input source is changed.

Hookup

• Use a miniplug cable to connect the AV receiver’s 12V

TRIGGER OUT A, B, or C jack to the 12 V trigger input on a connected component.

When several components are turned on simultaneously by using triggers A, B, and C, depending on the type of components, a large amount of current may be drawn momentarily. To prevent this, you can delay trigger signals A, B, and C individually. Another application for trigger delay is eliminating the “thump” noise that’s sometimes heard when a source component is turned on.

Delaying the trigger signal for your power amplifier so that it’s the last component to be turned on will accomplish this.

1



[Setup] button.


5

6

2

Use the Up and Down [ ]/[ ] buttons to select

“6. Miscellaneous,” and then press [Enter].

The Miscellaneous menu appears.


1.Volume Setup

2.OSD Setup

3.12V Trigger A Setup

4.12V Trigger B Setup

5.12V Trigger C Setup

Use the Up and Down [ ]/[ ] buttons to select an input source, and use the Left and

Right [ ]/[ ] buttons to select an option.

Off:

No trigger signal is output.

A 12-volt trigger signal is output when the connected component is selected as the source for:

Main:

Main room.

Zone2:

Zone 2.

Main/Z2:

Main room or Zone 2.


[Setup] button.

Setup closes.

98


Zone 2

—Continued

Using the Remote Controller in

Zone 2 and Multiroom Control Kits

To control the AV receiver with the remote controller while you’re in Zone 2, you’ll need a commercially available multiroom remote control kit for each zone.

• Multiroom kits are made by Niles and Xantech.

These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s installed inside a cabinet.

Using a Multiroom Kit with Zone 2

In this setup, the IR receiver in Zone 2 picks up the infrared signals from the remote controller and feeds them through to the AV receiver in the main room via the connecting block.

IR IN

A or B

IR Receiver

Connecting block

Remote controller

Main room Zone 2

Signal flow

The miniplug cable from the connecting block should be connected to the AV receiver’s IR IN A or B jack, as shown below. The IR IN A and B jacks are identical. Up to two IR receivers can be connected.

From the connecting block

Miniplug cable

B

IN

IR

OUT

A

AV receiver

Using a Multiroom Kit with a Cabinet

In this setup, the IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver located in the cabinet via the connecting block.

IR IN

A or B

Connecting block

IR Receiver

Inside cabinet

Signal flow

Remote controller

Using a Multiroom Kit with Other

Components

In this setup, an IR emitter is connected to the AV receiver’s IR OUT jack and placed in front of the other component’s remote control sensor. Infrared signals received at the AV receiver’s IR IN A or B jack are fed through to the other component via the IR emitter. Signals picked up by the AV receiver’s remote control sensor are not output.

IR IN

A or B

IR OUT

IR Receiver

Connecting block

AV receiver

IR Emitter

Remote controller

Other component

Signal flow

The IR emitter should be connected to the AV receiver’s

IR OUT jack, as shown below.

Miniplug cable

Other component

Remote control sensor

IR

B

IN

OUT

A

Miniplug

AV receiver

Signal flow

Emitter

IR Emitter

99


Controlling Other Components

You can control your DVD player, CD player, and other components with the AV receiver’s remote controller.

To control another component, you must first enter that component’s remote control code to a Remote Mode button.

This section explains how to enter remote control codes and how to control your other components.

Preprogrammed Remote Control

Codes

The following Remote Mode buttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components.

For details on controlling these components, see the pages indicated.

Integra/Onkyo DVD player (page 103)

Integra/Onkyo CD player (page 106)

Onkyo cassette recorder with

(page 108)

Entering Remote Control Codes

You’ll need to enter a code for each component that you want to control.

Remote indicator

Remote

Mode

Display

Receiver

1

2

(3 seconds)

While holding down the Remote

Mode button to which you want to enter a code, press and hold down the [Display] button until the Remote indicator lights up

(about 3 seconds).

Note:

• Remote control codes cannot be entered for the [Receiver] and

[Zone 2] Remote Mode buttons.

• Only TV remote control codes can be entered for the [TV] Remote Mode button.

• Apart from the [Receiver], [TV], and

[Zone 2] Remote Mode buttons, remote control codes from any category can be entered for the Remote

Mode buttons. However, these buttons also work as input selector but-

tons (page 48), so choose a Remote

Mode button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose the [CD] Remote Mode button when entering its remote control code.

3

Look up the component’s remote control code in the separate

Remote Control Codes list.

The codes are organized by category.

Within 30 seconds, use the number buttons to enter the 5-digit remote control code.

The Remote indicator flashes twice.

If the remote control code is not entered successfully, the Remote indicator will flash once slowly.

Number buttons

Note:

• The remote control codes provided are correct at the time of printing but subject to change.

100



—Continued

Remote Control Codes for Integra/Onkyo

Components Connected via

Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the

AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

1

Make sure the Integra/Onkyo component is connected with an cable and an analog audio cable (RCA).

See page 37 for details.

2

Enter the appropriate remote control code to the Remote Mode button.

• [DVD] Remote Mode button

31612:

Integra/Onkyo DVD player with

• [CD] Remote Mode button

71327:

Integra/Onkyo CD player with

• [Tape] Remote Mode button

42157:

Onkyo cassette recorder with

(default)

See the previous page for how to enter remote control codes.

3

Press the Remote Mode button, point the remote controller at the AV receiver, and operate the component.

If you want to control an Integra/Onkyo component by pointing the remote controller directly at it, or you want to control an Integra/Onkyo component that’s not connected via , use the following remote control codes:

• [DVD] Remote Mode button

30627:

Integra/Onkyo DVD player without

(default)

• [CD] Remote Mode button

71817:

Integra/Onkyo CD player without

(default)

Note:

• If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE

IN/OUT jacks, or connect an RI Dock to the

GAME/TV jacks, for to work properly, you must

set the Input Display accordingly (see page 46).

Resetting the Remote Mode Buttons

You can reset a Remote Mode button to its default remote control code.

1

While holding down the Remote

Mode button that you want to reset, press and hold down the

[Audio] button until the Remote indicator lights up (about 3 seconds).

2

(3 seconds)

Within 30 seconds, press the

Remote Mode button again.

The Remote indicator flashes twice, indicating that the button has been reset.

Each of the Remote Mode buttons is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

1

While holding down the

[Receiver] Remote Mode button, press and hold down the [Audio] button until the Remote indicator lights up (about 3 seconds).

2

(3 seconds)

Within 30 seconds, press the

[Receiver] Remote Mode button again.

The Remote indicator flashes twice, indicating that the remote controller has been reset.

101


102


—Continued

Controlling a TV

By pressing the [TV] or [Game/TV] Remote Mode buttons that’s been programmed with the remote control code for your TV (TV/DVD combination or TV/VCR combination), you can control your TV with the following buttons.

For details on entering a remote control code for a differ-

ent component, see page 100.

The [TV] and [Game/TV] Remote Mode buttons are preprogrammed with the remote control code for controlling a TV that supports the RIHD*. The TV must be able to receive remote control commands via RIHD and be connected to the AV receiver via HDMI. If controlling your TV via RIHD doesn’t work very well, program your TV’s remote control code into the [TV] Remote

Mode button and use the TV remote mode to control your TV.

Press [TV] Remote Mode button first

TV

A

A

B

C

D

E

F

G

H

J

Game/TV

K

L

M

N

O

A

On/Standby, TV [ ] buttons

Set the TV to On or Standby.

B

TV VOL [ ]/[ ]

Adjust the TV’s volume.

C

TV [Input] button

Selects the TV’s external inputs.

D

Guide button

Displays the program guide.

E


Used to navigate menus and select items.

F

Setup button

Displays a menu.

G

Playback buttons

From left to right: Previous, Rewind, Pause, Play,

Stop, Fast Forward, and Next.

These buttons works for combination devices.

H

SEARCH, REPEAT, RANDOM, and PLAY

MODE buttons

Function as colored buttons or A, B, C, D buttons.

I

Number buttons

Enter numbers. 0 button enters 11 on some components. +10 button works as “-.--” button or +10.

J

Display button

Displays information.

K

Muting button

Mutes the TV.

L

CH +/– button

Select channels on the TV.

M

PREV CH button

Selects the previous or last channel.

N

Return button

Exits the TV’s setup menu.

O

Audio button

Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).

P

CLR button

Cancels functions and clears entered numbers, or enters 12.

9

P

* The RIHD supported by the AV receiver is the CEC system control function of the HDMI standard.

* With some components, certain buttons may not work as expected, and some may not work at all.



—Continued

Controlling a DVD Player, or DVD Recorder

By pressing the Remote Mode button that’s been programmed with the remote control code for your DVD player (HD DVD, Blu-ray, or TV/DVD combination), you can control your player with the following buttons.

The [DVD] Remote Mode button is preprogrammed with the remote control code for controlling an Integra/Onkyo DVD player.



A

DVD

B

C

D

E

F

G

H

I

J

K

Press the appropriate Remote

Mode button first


L

M

N

O

P

Q

R

S

T

U

A

On/Standby button

Sets the DVD player to On or Standby.

B

TV [ ] buttons


C



D

TV VOL [ ]/[ ]


E

Top Menu button

Displays a DVD’s top menu or a DVD’s title.

F



G

Setup button

Used to access the DVD player’s settings.

H


From left to right: Previous, Next, Rewind, Play,

Fast Forward, Pause, and Stop.

I

Repeat button

Used with the repeat playback function.

J

Search buttons

Used to search title, chapter, and track numbers, and to search times for locating specific points.

K

Number buttons

Used to enter title, chapter, and track numbers, and to enter times for locating specific points. The [+10] button works as a +10 button or “-.--” button.

L

Display button

Displays information about the current disc, title, chapter, or track, including elapsed time, remaining time, total time, and so on.

M



N

Disc +/–, CH +/– button

Selects discs on a DVD changer. Selects TV channels on a component with a built-in tuner.

O

VOL [ ]/[

] button (48)

Adjusts the volume of the AV receiver.

P

Menu button

Displays a DVD’s menu.

Q

Return button

Exits the DVD player’s setup menu or returns to the previous menu.

R

Audio button


S

Random button

Used with the random playback function.

103


104


—Continued

T

Play Mode button

Selects play modes on components with selectable play modes.

U

CLR button

Cancels functions and clears entered numbers.

Note:

• If you enter the remote control code for a HD DVD or

Blu-ray player that has A, B, C, and D or colored buttons, the [SEARCH], [REPEAT], [RANDOM], and

[PLAY MODE] buttons will work as colored or A, B,

C, D buttons. In this case, these buttons cannot be used to set repeat playback, random playback, or select play modes.

Controlling a VCR or DVR

By pressing the Remote Mode button that’s been programmed with the remote control code for your VCR

(TV/VCR, DVR, DBS/DVR combination or cable/DVR combination), you can control your video recorder with the following buttons.



A

VCR/DVR

B

C

D

E

F

G

H

I




J

K

L

M

N

O

P

Q

R

A


Set the video recorder to On or Standby.

B

TV [ ] buttons


C



D

TV VOL [ ]/[ ]


E

Guide button

Displays the program guide or navigation list.

F



G

Setup button

Displays the video recorders setup menu.

H

Previous [ ] button

Previous or instant replay function.

I

Number buttons

Enter numbers. The [0] button enters 11 on some components. The [+10] button works as a +10 button or “-.--” button.

J

Display button


K



L

CH +/– button

Selects TV channels on the video recorder.

M

VOL [ ]/[

] button (48)


N

PREV CH button

Selects the previous channel.

O

Return button

Exits the menu or returns to the previous menu.

P

Next [ ] button

Next or advance function.

Q




R

CLR button

Cancels functions or enters the number 12.



—Continued

Controlling a Satellite Receiver or Cable Receiver

By pressing the Remote Mode button that’s been programmed with the remote control code for your satellite receiver, cable receiver, or DVD recorder (DBS/DVR combination or cable/DVR combination), you can control your player with the following buttons.



A

B

C

D

E

6



7

CBL/SAT

8

9

J

K

L

M

N

O

A


Set the component to On or Standby.

B

Guide button

Displays the onscreen program guide.

C



D

Setup button

Displays the setup menu.

E

SEARCH, REPEAT, RANDOM, and PLAY

MODE buttons

Function as colored buttons or A, B, C, D buttons.

F

Number buttons

Enter numbers. The [+10] button works as a +10 button or “-.--” button.

G

Display button


H



I

CH +/– button

Selects satellite/cable channels.

J

VOL [ ]/[

] button (48)


K

PREV CH button

Selects the previous channel.

L

Return button

Exits the menu.

M

Audio button


N




O

CLR button



105



—Continued

Controlling a CD Player, CD Recorder, or MD Player

By pressing the Remote Mode button that’s been programmed with the remote control code for your CD player, CD recorder, or MD player, you can control your player with the following buttons.

The [CD] Remote Mode button is preprogrammed with the remote control code for controlling an Integra/Onkyo

CD player.



A

CD

B

C

D

E

F

G

H



I

J

K

L

M

N

O

P

A


Set the component to On or Standby.

B

Top Menu button

Displays a menu.

C



D

Setup button

Used to access the Integra/Onkyo CD player’s settings.

E


From left to right: Previous, Rewind, Pause, Play,

Stop, Fast Forward, and Next.

F

Repeat button

Used with the repeat playback function.

G

Search button

Used to locate specific points.

H

Number buttons

Used to enter track numbers and times for locating specific points. The [+10] button works as a +10 button or “-.--” button.

I

Display button

Displays information about the current disc or track, including elapsed time, remaining time, total time, and so on.

J



K

Disc +/– button

Selects discs on a CD changer.

L

VOL [ ]/[

] button (48)


M

Return button

Exits the menu.

N

Random button

Used with the random playback function.

O



P

CLR button


106




—Continued

Controlling an RI Dock

By pressing the Remote Mode button that’s been programmed with the remote control code for your RI Dock, you can control your iPod in the RI Dock with the following buttons.

For details on entering a remote control code, see

page 100.

When Using an RI Dock:

• Connect the RI Dock to the TAPE IN or GAME/TV

IN L/R jacks.

• Set the RI Dock’s RI MODE switch to HDD or

HDD/DOCK.

• Set the AV receiver’s Input Display to DOCK (see

page 46).

• See to the RI Dock’s instruction manual for more information.

A

2

3

4

5

6

7




8

I

J

K

L

M

N

O

P

Q

R

S

A


Turns the iPod on or off.

Notes:

• This button does not turn the Onkyo DS-A2 or

DS-A2X RI Dock on or off.

• Your iPod many not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod is already on, it will remain on when the remote controller transmits an On command. Similarly, if your iPod is already off, it will remain off when the remote controller transmits an Off command.

B

Top Menu button

Works as a Mode button when used with a DS-A2

RI Dock.

C

Arrow [ ]/[ ] and Enter buttons*


D

Previous [ ] button

Restarts the current song. Press it twice to select the previous song.

E

Rewind [ ] button

Press and hold to rewind.

F

Pause [ ] button

Pauses playback. (With 3rd generation iPod models, it works as a Play/Pause button.)

G

Repeat button*

Used with the repeat function.

H

Display button*

Turns on the backlight for 30 seconds.

I



J

Album +/– button*

Selects the next or previous album.

K

VOL [ ]/[

] button (48)


L

Menu button*

Displays a menu.

M

Playlist [ ]/[ ] buttons*

Selects the previous or next playlist on the iPod.

N

Play [ ] button

Starts playback. If the component is off, it will turn on automatically. (With 3rd generation iPod models, this button works as a Play/Pause button.)

O

Next [ ] button

Selects the next song.

107



—Continued

P

Fast Forward [ ] button

Press and hold to fast forward.

Q

Stop [ ] button

Stops playback and displays a menu.

R



Controlling a Cassette Recorder

By pressing the Remote Mode button that’s been programmed with the remote control code for your cassette recorder, you can control your cassette recorder with the following buttons.

The [Tape] Remote Mode button is preprogrammed with the remote control code for controlling an Onkyo cassette recorder when used with an connection.



A



Tape

F

G

Works as a Resume button when used with a DS-A2

RI Dock.

S

Random button*

Used with the shuffle function.

* Buttons marked with an asterisk (*) are not supported by 3rd generation iPod models.

On twin cassette decks, only Deck B can be controlled.

A


Turns the cassette recorder on or off.

B

Previous and Next [ ]/[ ] buttons

The Previous [ ] button selects the previous track. During playback it selects the beginning of the current track. The Next [ ] button selects the next track.

Depending on how they were recorded, the Previous and Next [ ]/[ ] buttons may not work properly with some cassette tapes.

C

Rewind and Fast Forward [ ]/[ ] buttons

The Rewind [ ] button starts rewind. The Fast

Forward [ ] button starts fast forward.

D

Reverse Play [ ] button

Starts reverse playback.

E

Play [ ] button

Starts playback.

F



G

VOL [ ]/[

] button (48)


H

Stop [ ] button

Stops playback.

Note:

• An Onkyo cassette recorder connected via can also be controlled in Receiver mode.

2

3

4

5

2

3

H


108


Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer.

If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer.

To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [On/Standby] button. “Clear” will appear on the display and the AV receiver will enter Standby mode.

Note that resetting the AV receiver will delete your radio presets and custom settings.



Power

Can’t turn on the AV receiver

• Make sure that the power cord is plugged into the wall outlet properly.

• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it back in again.

The AV receiver turns off as soon as it’s turned on

• The amp protection circuit has been activated.

Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact the dealer.

Audio

There’s no sound or it’s very quiet

• To listen to an audio source that’s connected to an

HDMI input, make sure that input is assigned to an

input selector (page 44).

• To listen to an audio source that’s connected to an

OPTICAL or COAXIAL input, make sure that input is

assigned to an input selector (page 45).

• Make sure that all audio connecting plugs are pushed

in all the way (page 21).

• Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with the

metal part of each speaker terminal (page 16).

• Make sure that the speaker cables are not shorting.

• Check the volume (page 48). The AV receiver is

designed for home theater enjoyment and has a wide volume range for precise adjustment.

• If the MUTING indicator is flashing on the display, press the remote controller’s [Muting] button to

unmute the AV receiver (page 49).

• While a pair of headphones is connected to the

PHONES jack, no sound is output by the main room

speakers (page 50).

• Check the digital audio output settings on the source component. On some game consoles, such as those that can play DVDs, the default setting is off.

• With some DVD-Video discs, you need to select an audio format from a menu or with the Audio button on your DVD player’s remote controller.

• If your turntable doesn’t have a phono preamp built-in, you must connect one between it and the AV receiver.

• If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer and a phono preamp.

• Check the speaker settings (pages 82–86).

• If the digital signal format is set to PCM or DTS, set it

to Auto (page 51).

• If there’s no sound from a DVD player connected to an

HDMI IN, check the DVD player’s output settings, and be sure to select a compatible audio format.

Only the front speakers produce sound

• When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

• Check the Speaker Configuration (page 82).

Only the center speaker produces sound

• If you use the Dolby Pro Logic IIx Movie or Dolby

Pro Logic IIx Music listening mode with a mono source, such as an AM radio station or mono TV program, the sound will be concentrated in the center speaker.


The center speaker produces no sound

• When the Stereo or Mono listening mode is selected,

the center speaker produces no sound (page 74).


The surround speakers produce no sound

• When the Stereo or Mono listening mode is selected, the surround speakers produce no sound.

• Depending on the source and the current listening mode, not much sound may be produced by the sur-

round speakers. Try another listening mode (page 67).


The surround back speakers produce no sound

• The surround back speakers are not used with all lis-

tening modes. Try another listening mode (page 67).

109


110

Troubleshooting

—Continued

• Not much sound may be produced by the surround back speakers with some sources.


• While Powered Zone 2 is being used, playback in the main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 94).

The subwoofer produces no sound

• If the source material contains no audio in the LFE channel, the subwoofer produces no sound.


The Zone 2 speakers produce no sound

• The Zone 2 speakers only output sources that are connected to an analog input. Check to see if the source component is connected to an analog input.

• Powered Zone 2 cannot be used if Speaker Type is set

to Bi-Amp (page 43).

There’s no sound with a certain signal format

• Check the digital audio output setting on the source component. On some game consoles, such as those that can play DVDs, the default setting is off.

• With some DVD-Video discs, you need to select an audio format from a menu or with the Audio button on your DVD player’s remote controller.

Can’t get 6.1- or 7.1-channel playback

• While Powered Zone 2 is being used, playback in the main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 94).

The volume cannot be set to 79

• Check to see if a maximum volume has been set

(page 88).

• After the Automatic Speaker Setup function has been run, or the volume level of each individual speaker has

been adjusted (pages 39 and 85), the maximum vol-

ume may be reduced.

• When the levels of each speaker have been adjusted

(page 85), the maximum possible volume may be

reduced.

• When the Equalizer setting (page 86) is set to Audys-

sey, the maximum possible volume is reduced by

6 dB.

Noise can be heard

• Using cable ties to bundle audio cables with power cords, speaker cables, and so on can degrade audio performance, so don’t use them.

• An audio cable may be picking up interference. Try repositioning your cables.

The Late Night function doesn’t work

• Make sure that the source is Dolby Digital or

Dolby TrueHD (page 79).

The analog multichannel input doesn’t work

• Check the multichannel input connections (page 26).

• Make sure that the multichannel input is selected

(page 48).

• Check the audio output settings on your DVD player.

About DTS signals

• When playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

• When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, as the AV receiver does not switch formats immediately, you may not hear anything, in which case you should stop your player for about 3 seconds, and then resume playback.

• With some CD players, you won’t be able to playback

DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

The beginning of audio received by an HDMI IN can’t be heard

• Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio signals, sound may not be output immediately.

Video

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 21).

• Make sure that each video component is properly connected.

• On your TV, make sure that the video input to which the AV receiver is connected is selected.

• If the video source is connected to an HDMI input, you must assign that input to an input selector

(page 44), and your TV must be connected to the

HDMI OUT (page 32).

• If the video source is connected to a component video input, you must assign that input to an input selector

(page 45), and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO OUT

(page 32, 24).

• If the video source is connected to an S-Video or composite video input, your TV must be connected to the

HDMI OUT or the corresponding S-Video or compos-

ite video output (page 32, 24).

There’s no picture from a source connected to an HDMI IN

• Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC

are not supported (page 32).


Troubleshooting

—Continued

• If the message “Resolution Error” appears on the AV receiver’s display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player.

Tuner

Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t light up

• Relocate your antenna.

• Move the AV receiver away from your TV or computer.

• When listening to an AM station, operating the remote controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor antenna.


The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 13).

• Make sure that the remote controller is not too far away from the AV receiver and there’s no obstruction between the remote controller and the AV receiver’s

remote control sensor (page 13).

• Make sure you’ve selected the correct remote controller mode.

• Make sure you’ve entered the correct remote control

code (page 100).

Can’t control other components

• Make sure you’ve selected the correct remote controller mode.

• If you’ve connected an -capable Onkyo MD recorder, CD recorder, or RI Dock to the TAPE

IN/OUT jacks, or an RI Dock to the GAME/TV IN jacks, for the remote controller to work properly, you must set the Input Display to MD, CDR, or DOCK,

respectively (see page 46).

• The entered remote control code may not be correct. If more than one code is listed, try each one.

• With some AV components, certain buttons may not work as expected, and some may not work at all.

• To control an Integra/Onkyo component that’s connected via , point the remote controller at the AV receiver. Be sure to enter the appropriate remote con-

trol code first (page 101).

• To control an Integra/Onkyo component that’s not connected via , or another manufacturer’s component, point the remote controller at that component. Be sure to enter the appropriate remote control code first

(page 100).

Recording

Can’t record

• On your recorder, make sure the correct input is selected.

• To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e.g., TAPE IN to TAPE OUT or

VCR/DVR IN to VCR/DVR OUT).

Others

The sound changes when I connect my headphones

• When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo,

Mono, and Direct, in which case it stays the same.

How do I change the language of a multiplex source

• On the “Audio Adjust” menu, change the “Input Ch”

setting to Main or Sub (page 77).

The functions don’t work

• To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digi-

tally (page 37).

• While Zone 2 is selected, the functions don’t work.

The following settings can be made for the

S-Video and composite video inputs

You must use the buttons on the unit to make these settings.

1. While holding down the input selector button for the input source that you want to set, press the [Setup] button.

2. Use the Left and Right [ ]/[ ] buttons to change the setting.

3. Press the [Setup] button when you’ve finished.

• Video Attenuation

This setting can be made for the DVD, VCR/DVR,

CBL/SAT, Game/TV, or AUX input.

If you have a games console connected to the

S-Video or composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT:0:

(default).

Video ATT:2:

Gain is reduced by 2 dB.

111


Troubleshooting

—Continued

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least 5 seconds, and then plug it back in again.

Integra/Onkyo is not responsible for damages (such as

CD rental fees) due to unsuccessful recordings caused by this unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby.

Important Note Regarding Video Playback

The AV receiver can upconvert component video, S-Video, and composite video sources for display on a

TV connected to the HDMI OUT. However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether.

In this case, try setting the HDMI Output Resolution setting (page 90) to 480p or 720p. If that doesn’t

improve the picture quality, try the following:

1. If the video source is connected to a component video input, connect your TV to the COMPONENT VIDEO OUT.

If the video source is connected to an S-Video input, connect your TV to an S-Video output.

If the video source is connected to a composite video input, connect your TV to a composite video output.

2. On the main menu, select “1. Input Assign,” and then select “1. HDMI Input.”

Select the relevant input selector, and assign it to “-----” (page 44).

3. On the main menu, select “1. Input Assign,”

and then select “2. Component Video Input” (page 45):

If the video source is connected to COMPONENT VIDEO IN 1, select the relevant input selector, and assign it to “IN1.”

If the video source is connected to COMPONENT VIDEO IN 2, select the relevant input selector, and assign it to “IN2.”

If the video source is connected to an S-Video input or composite video input, select the relevant input selector, and assign it to “-----”.

112


Specifications

Amplifier Section

Rated Output Power

North American:

90 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20Hz to 20kHz, with a maximum total harmonic distortion of 0.08% (FTC)

105 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1kHz, with a maximum total harmonic distortion of 0.7% (FTC)

110 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1kHz, with a maximum total harmonic distortion of 0.1% (FTC)

Oceanian:

7 ch

×

175 W at 6 ohms, 1kHz, 1 ch driven (JEITA)

Dynamic Power 210 W (3

180 W (4

110 W (8

Ω

Ω

Ω

, Front)

, Front)

, Front)

THD (Total Harmonic

Distortion)

Damping Factor

Input Sensitivity and

Impedance

Output Level and

Impedance

Frequency Response

Tone Control

0.08% (Power Rated)

0.08% (20Hz to 20kHz Power Rated)

60 (Front, 1kHz, 8

200 mV/ 47 k

Ω

Ω

)

(LINE)

200 mV/ 2.2 k

Ω

(REC OUT)

5Hz–100kHz/ +1 dB–3 dB (direct mode)

±10 dB, 50Hz (BASS)

±10 dB, 20kHz (TREBLE)

Signal to Noise Ratio 106 dB (LINE, IHF-A)

Speaker Impedance

North American: 6

Ω

–16

Ω

Oceanian: 4

Ω

–16

Ω

Video Section

Input Sensitivity/Output

Level and Impedance 1 Vp-p /75

Ω

(Component and S-Video Y)

0.7 Vp-p /75

Ω

(Component Pb/Cb, Pr/Cr)

0.28 Vp-p /75

Ω

(S-Video C)

1 Vp-p /75

Ω

(Composite)

Component Video

Frequency Response 5Hz – 50MHz, –3 dB

Tuner Section

■

FM

Tuning Frequency Range

North American: 87.5MHz–107.9MHz

Asian and Oceanian: 87.50MHz–108.00MHz, RDS

■

AM

Tuning Frequency Range

North American: 530kHz–1710kHz

Asian and Oceanian: 522kHz–1611kHz

■

Digital Tuner

North American: SIRIUS

Preset Channel 40

General

Power Supply

North American: AC 120 V, 60Hz

Asian and Oceanian: AC 230 V, 50Hz

Power Consumption

North American: 5.5 A

Asian and Oceanian: 550 W

Dimensions

(W

×

H

×

D) 435

×

173

×

17-1/8"

×

391 mm

6-13/16"

×

15-3/8"

Weight

North American: 11.6 kg

25.6 lbs.

Asian and Oceanian: 11.5 kg, 25.4 lbs.

■

Video Inputs

HDMI (Assignable)

Component

Composite

S-Video

IN 1, IN 2, IN 3, IN 4

IN 1, IN 2

DVD, VCR/DVR, CBL/SAT, GAME/TV,

AUX

DVD, VCR/DVR, CBL/SAT, GAME/TV

■

Video Outputs

HDMI

Component

Composite

S-Video

OUT

OUT

MONITOR OUT, VCR/DVR (REC OUT)

MONITOR OUT, VCR/DVR (REC OUT)

■

Audio Inputs

Digital Inputs

(Assignable)

Analog Inputs

Multichannel Inputs

2 (Rear OPT), 2 (Rear coax)

DVD (MULTICHANNEL), VCR/DVR,

CBL/SAT, GAME/TV, AUX, TAPE, CD

7.1 ch

■

Audio Outputs

Digital Outputs 1 (Optical)

TAPE, VCR/DVR, ZONE 2 Analog Outputs

Multichannel Pre

Outputs 7ch

Subwoofer Pre Outputs 1

Speaker Outputs Main (L, R, C, SL, SR, SBL, SBR)

+ ZONE2 (L, R)

Phones 1

■

Mic

Control Terminal

Yes

RS232

Ether

IR Input/Output

12V Trigger Out

1

1

2/1

3

Specifications and features are subject to change without notice.

113


Video Resolution Chart

The following tables show how video signals at different resolutions are output by the AV receiver.

NTSC

Input

HDMI

COMPONENT

S

-

VIDEO

COMPOSITE

Output

HDMI

COMPONENT

S

-

VIDEO

COMPOSITE

NTSC PAL NTSC PAL

480i 480i 480i

1080P

1080i

720P

480P

480i

1080P 1080i 720P 480P 480i 1080P 1080i 720P 480P 480i 480i

✔

✔

✔

✔

✔

1080P

1080i

✔

720P

480P

480i

480i

480i

✔

✔

✔

✔

✔

✔

✔

✔

✔ ✔

✔ ✔ ✔

✔ ✔ ✔

✔ ✔ ✔

✔

✔

✔

✔

✔

PAL

Input

HDMI

COMPONENT

S

-

VIDEO

COMPOSITE

Output

HDMI

COMPONENT

S

-

VIDEO

COMPOSITE

NTSC PAL NTSC PAL

576i 480i 576i

1080P

1080i

720P

576P

576i

1080P 1080i 720P 576P 576i 1080P 1080i 720P 576P 576i 480i

✔

✔

✔

✔

✔

1080P

1080i

720P

576P

576i

576i

576i

✔

✔

✔

✔

✔

✔

✔

✔

✔ ✔

✔ ✔ ✔

✔ ✔ ✔

✔ ✔ ✔

✔

✔

✔

✔

✔

✔

114


Onscreen Setup Menus

The onscreen setup menus appear on the connected TV and provide a convenient way to change the AV receiver’s various settings. Settings are organized into eight categories on the

main menu

, most containing a

submenu

.

The onscreen setup menus appear only on a TV that is connected to the

HDMI OUT. If your TV is connected to the composite video or S-Video

MONITOR OUT, or the COMPONENT VIDEO OUT, use the DTR-5.9’s display when changing settings.

Menu

1. Input Assign


3. Audio Adjust

4. Source Setup




8. Lock Setup

Menu Map

The following map shows how the setup menus are organized. Use the page numbers to locate information about items.

Main menu Submenu

Menu

1. Input Assign


3. Audio Adjust

4. Source Setup




8. Lock Setup

☞ pages 44–45

1. Input Assign

1. HDMI Input

2. Component Video Input

3. Digital Audio Input

☞ page 88


1. Volume Setup

2. OSD Setup

3. 12V Trigger A Setup

4. 12V Trigger B Setup

5. 12V Trigger C Setup

☞ pages 82–86


1. Speaker Settings

2. Speaker Configuration

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

page 43

☞ page 77

3. Audio Adjust

1. Multiplex/Mono

2. PL x/Neo:6

3. Dolby EX

4. Theater-Dimensional

☞ page 89



2. Zone2

3. Tuner


5. HDMI

6. Network

☞ page 92

8. Lock Setup

Lock Unlocked

page 94

☞ pages 87

4. Source Setup

1. IntelliVolume

2. A/V Sync

DVD

☞ page 81


1. DVD

2. VCR/DVR

3. CBL/SAT

4. GAME/TV

5. AUX

6. TAPE

7. TUNER

8. CD

115


Integra Division of

ONKYO U.S.A. CORPORATION

18 park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com

Integra Division of

ONKYO CORPORATION

Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

SN 29344688

(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.

116

E n

I0804-1

* 2 9 3 4 4 6 8 8 *

No results