SUMMER RAIN™ 2 WALL & 3 WALL WALK-IN SHOWER SYSTEMS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFETY INFORMATION Do not place or use electrically connected devices, such as television, radio, or stereo speakers, lights, hair dryers, or telephones, within 1.5 m (5 feet) of shower. Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does not cover improper installation related problems. CONTENTS 2 WALL Specifications _________________________________________________________________________ 2 Rough-in Reference ____________________________________________________________________ 3 Component Identification ________________________________________________________________ 4 Base Installation _______________________________________________________________________ 5-7 Tower and Glass Panels Installation ________________________________________________________ 8-12 3 WALL Specifications _________________________________________________________________________ 13 Rough-in Reference ____________________________________________________________________ 14 Component Identification ________________________________________________________________ 15 Base Installation _______________________________________________________________________ 16-18 Tower and Glass Panels Installation ________________________________________________________ 19-22 2 & 3 WALL Operation ___________________________________________________________________________ 23 Maintenance __________________________________________________________________________ 24 Authorized Service _____________________________________________________________________ 24 Tower Fixture Repair Parts _______________________________________________________________ 25 Tower Plumbing Repair Parts _____________________________________________________________ 26 2 Wall Unit Repair Parts _________________________________________________________________ 27 3 Wall Unit Repair Parts _________________________________________________________________ 28 Warranty _____________________________________________________________________________ 29-30 Save These Instructions for Future Use. Owner's Record Date Purchased ____________________________________________________________ Purchased From ____________________________________________________________ Installed By ________________________________________________________________ Serial Number _____________________________________________________________ Model ____________________________________________________________________ 1 2 WALL SPECIFICATIONS Important: Read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for parts and hardware. Should inspection reveal any damage or defect in any component, do not install the unit. Damage or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection. L BASE SPECIFICATIONS 45° ELBOW 2 PROVIDED (LOOSE) DIMENSIONS 60" (1219 mm) L 42-5/16" ( 1075 mm) W 4" ( 102 mm) H 1-1/2" TILE FLANGE 1/2" RIGID COPPER PIPE UNDER BASE PRODUCT WEIGHT (Base + Enclosure ) 196 lb (89 kg) W TOTAL WEIGHT/ FLOOR LOADING 396 lb (180 kg)/ 23 lb/sq. ft. (112 kg/sq. m) TOP VIEW NOTE: MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40 PSI. 1-1/2" TILE FLANGE H FRONT VIEW 2 2 WALL ROUGH-IN REFERENCE 84" FRONT VIEW 60" 33-3/4" 1-1/2" TILE FLANGE 23" 21-1/2" 1/2" RIGID COPPER PIPE UNDER BASE 27-15/16" 42-5/16" COLD SUPPLY HOT SUPPLY MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40PSI TOP VIEW 3 2 WALL COMPONENT IDENTIFICATION STRAIGHT GLASS MOUNTING WALL POST MOUNTING CAP (2) POST TOWER WITH PLUMBING, FIXTURES, MAGNETIC GASKET, BOTTOM PLATE AND TOP COVER (PREASSEMBLED) HEX WRENCH (1) (PROVIDED) WALL MOUNT BRACKET (2) TOWER SUPPORT RAIL BRACKET COVER (2) GLASS PANEL SUPPORT RAIL CURVED GLASS WALL MOUNTING POST FRONT RAIL GLAZING GASKET TAPE (6 PIECES) 3 SCREWS AND 3 WALL ANCHORS PER MOUNTING POST GLAZING GASKET (3) CURVED GLASS STRAIGHT GLASS PANEL BOTTOM BRACKET CORNER POST GLAZING GASKET TOWER COVER TOWER MOUNTING BOLT & WASHER SELF DRILLING SCREW BASE 4 2 WALL BASE INSTALLATION PRELIMINARY ROUGH-IN INSTALLATION INSTRUCTIONS The floor structure beneath the unit must be able to support a total weight of the unit and bather. Refer to the table under total weight. STEP 2 Remove the stainless steel strainer from the drain assembly. Disassemble the locknut and two gaskets from the back of the drain assembly. Apply a 1/4" bead of caulking (silicone) to the drain hole and insert the drain assembly. Replace the rubber washer, fiber washer, and lock nut in that order. Hand tighten the locknut. Remove excess sealant from finished side. Apply a lubricant (common household liquid soap works well) to the inside of the rubber seal of the drain assembly. STEP 1 Provide an opening in the subfloor no less than 5" x 5" square. This opening should be located on the center lines of the shower base drain hole (See Product Chart). The opening is to accommodate a 2" waste pipe. The waste pipe should be 1/4" to 1/2" above the surface of the subfloor. STRAINER APPLY LUBRICANT DRAIN ASSEMBLY SILICONE SEALANT 90° SHOWER BASE 90° 90° RUBBER WASHER 5"x5" OPENING (MIN. AS POSSIBLE) 2" WASTE PIPE FIBER WASHER As shown in top view, 1/2" copper pipes are provided to connect to the water supply. Also provided are 2 loose 45° elbows as shown for installation in Detail 1. NUT STEP 3 If the subfloor is level, no other preparation is necessary. You can proceed to install the shower base. If the subfloor is not level, level shower base by spreading floor leveling compound, mortar, plaster or minimal expansion structural foam with a minimum density of 5 lbs./cubic feet EVENLY over ENTIRE area where base will be installed. The compound used MUST make contact with the entire bottom surface of the base. Both sides of a joint or splice of subfloor should be level to each other. Level and support waste pipe cutout area greater than 5" x 5". The base is NOT to be supported by the tile flange. CAUTION: A nonflammable protective barrier must be placed between soldering work and base unit to prevent damage to the base. When connecting the supply lines, the toe plate can be notched to accommodate the pipes. The pipe under the base can be cut to length. To do so, remove the pipe clamps under the base, cut the pipe and reinstall pipes. STUD WALL NOT PROVIDED 45° ELBOW PROVIDED (2) DEATAIL 1 SPREAD MORTAR OR LEVELING COMPOUND ETC. EVENLY OVER ENTIRE AREA 5 2 WALL BASE INSTALLATION STEP 4 With the drain fitting passing over the center of the drainpipe, lower the shower base carefully into place, push down firmly until the base is in place. You must check the level of the base in two directions. Do not lift a corner to level the base. This will cause a loss of contact with the mortar. Attach the shower base flange to the stud wall and blocking with self-drilling screws (included). Use a minimum of 3 screws per flange section. STEP 5 With a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal the drain pipe connection. After drain is fully installed, test for proper drainage. If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath is not responsible for removal and/ or reinstallation costs. NOTE: Watertight installation of the drain is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty. Replace the strainer and tape over the drain hole to prevent finishing material from entering drain. TIGHTEN SEALING NUT TOOL (INCLUDED) POSITION BASE OVER CENTER OF DRAIN PIPE AND SET INTO PLACE NOTE: If there is any gap between base flange and stud or blocking, shims MUST be used to prevent distortion or cracking of the flange. TILE FLANGE SHIM TILE FLANGE GAP USE SCREWS (PROVIDED) USE SCREWS (PROVIDED) STUD STUD INCORRECT CORRECT 6 2 WALL BASE INSTALLATION STEP 6 STEP 8 Place cement board or equivalent on top of shower base flange and secure to studwall. Filling the area marked DO NOT FILL will prevent moisture from draining back into the base through the weep holes. This moisture is due to leakage through the tile grout. Sealing the tile grout will prevent this leakage. CEMENT BOARD TILE CEMENT BOARD STUD GROUT STUD SILICONE SEALANT SHIM IF NECESSARY DO NOT FILL STEP 7 Apply tile (or other finishing material) leaving a 1/8" gap between the finishing material and the shower base flange lip. Seal this gap with silicone sealant. Leave a minimum 1/4" gap at the back and front corners of the shower base to allow drainage from leakage through unsealed tiled grout. 1-1/8" MAXIMUM NO MINIMUM CLEAN-UP AFTER INSTALLATION To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent and warm water clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge. Paint, tar, or other difficult stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper. You can restore the glossy finish to the acrylic surface of the base with a special compound, Meguiar’s #10 Mirror Glaze. If not available, use automotive rubbing compound followed by an application of automotive paste wax. Major scratches and gouges which penetrate the acrylic surface require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for special instructions. TILE 1/4" MINIMUM GAP CEMENT BOARD TILE ADHESIVE SILICONE SEALANT STUD 1/8" GAP SILICONE SEALANT 1/4" MINIMUM GAP 7 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 3A Slide straight glass panel all the way into wall post. Mark position of glass post. Remove panel. STEP 1 Position the wall posts so the edge of the post is set back 3/4" (19 mm) in from the edge of the base 3/4" (19 mm) FINISH WALL EDGE OF BASE STEP 2 Level both wall posts in their proper position and mark where screw holes are to be drilled. Drill 3/16" holes and secure with wall anchors and screws provided. Cut a 12" strip of tape (provided) and apply firmly over screw heads. MARK POSITION STEP 3B Apply a bead of silicone sealant on underside of bottom bracket corner post and place bracket where marked. Drill pilot holes (#8 screw) and secure bracket to base. Reinsert panel into wall post and position glass post over bracket. TAPE 6 PLACES) APPLY BEAD OF SILICONE SEALANT ON UNDERSIDE OF BOTTOM BRACKET CORNER POST 8 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 4 Slide the glass panel into the wall post. Make sure that the corner notch is positioned toward the base of the tower. STEP 6 Insert tower support rail into glass panel rail but do not tighten at this time. GLASS PANEL SUPPORT RAIL TOWER SUPPORT RAIL STEP 7 Insert support rails into brackets in top moulding of tower but do not tighten at this time. Front and tower support rails may have to be cut if they are too long. TOWER SUPPORT RAIL NOTCH FRONT RAIL GLASS PANEL SUPPORT RAIL STEP 5 Place the tower onto base. Ensure the curved glass locates into the glazing channel. Install bolt but do not tighten. BOLT (5/16") STEP 8 Slide mounting bracket covers and mounting brackets onto front rail and tower support rail. WASHER GLAZING CHANNEL RAIL MOUNTING BRACKET COVER RAIL WALL MOUNTING BRACKET 9 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 9 Place the front rail and tower support rail against the walls. Check level and mark the position for the rail mounting bracket. The screw position will be above the rail. Drill the wall with a 3/16" bit and secure bracket with screws and wall anchors provided. STEP 11 Secure the rails. ATTACH RAIL BRACKET TO WALL SECURE RAIL TO BRACKET (TURN CW TO TIGHTEN) STEP 12 Tighten the tower base bolt. Two shut-off valves are provided. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw valve to stub outs at bottom of tower. Then reconnect braided line using provided gasket. Do not twist or kink supply lines when connecting. MOVE COVER CAP OVER BRACKET STEP 10 Adjust the rails until tower is vertical in 2 planes. SHUT OFF VALVES (PROVIDED) COLD BOLT 10 HOT 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 14 Install cover cap on fixed glass wall post. STEP 13A Insert fixed glass support rail into panel post and tighten set screw. COVER CAP STEP 13B Drill a 1/8" pilot hole into tower support rail using the hole in the glass panel support rail. Screw M3.5X9.5 mm screw into hole. STEP 15 Install glazing gasket on curved glass wall post on the outside. Note orientation of gasket. Soapy water may help to insert the glazing gasket. On the inside of enclosure, apply sealant the entire length of glass and wall post as well as the entire length of glass and tower. DRILL 1/8" PILOT HOLE AND SCREW M3.5X9.5 mm SCREW INTO HOLE GLASS PANEL SUPPORT RAIL GLASS WALL POST GLAZING GASKET INSIDE OF ENCLOSURE APPLY SEALANT GLAZING GASKET TOWER TOP PLATE APPLY SEALANT 11 INSIDE OF ENCLOSURE 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 16 Turn on water supply and check for leaks. Correct any leaks before installing tower cover. STEP 18 Seal all around the base of tower with silicone sealant. Also seal the inside of both wall posts, glass post and the bottom of both glass panels on the inside only. STEP 17 Install tower cover as shown. Insert cover at top first. APPLY SEALANT ALONG BASE AND SIDE OF WALL POST TOWER TOP PLATE APPLY SEALANT ALONG BASE OF GLASS APPLY SEALANT ALONG BASE OF GLASS TOWER COVER INSERT THIS SIDE FIRST APPLY SEALANT APPLY SEALANT APPLY SEALANT AROUND ALL AROUND ALONG BASE GLASS POST TOWER BASE AND SIDE OF WALL POST TOWER COVER (RAILS NOT SHOWN) TOP VIEW 12 3 WALL SPECIFICATIONS Important: Read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for parts and hardware. Should inspection reveal any damage or defect in any component, do not install the unit. Damage or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection. L BASE SPECIFICATIONS 45° ELBOW 2 PROVIDED (LOOSE) DIMENSIONS 60" (1219 mm) L 42-5/16" ( 1075 mm) W 4" ( 102 mm) H 1-1/2" TILE FLANGE 1/2" RIGID COPPER PIPE UNDER BASE PRODUCT WEIGHT (Base + Enclosure ) 140 lb (64 kg) W TOTAL WEIGHT/ FLOOR LOADING 340 lb (155 kg)/ 23 lb/sq. ft. (97 kg/sq. m) TOP VIEW NOTE: MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40 PSI. 1-1/2" TILE FLANGE H FRONT VIEW 13 3 WALL ROUGH-IN REFERENCE 84" FRONT VIEW 60" 33-3/4" 1-1/2" TILE FLANGE 23" 21-1/2" 1/2" RIGID COPPER PIPE UNDER BASE 27-15/16" 42-5/16" COLD SUPPLY HOT SUPPLY MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40PSI TOP VIEW 14 3 WALL COMPONENT IDENTIFICATION TOWER WITH PLUMBING, FIXTURES, MAGNETIC GASKET, BOTTOM PLATE AND TOP COVER (PREASSEMBLED) HEX WRENCH (1) (PROVIDED) WALL MOUNT BRACKET (2) CURVED GLASS WALL MOUNTING POST TOWER SUPPORT RAIL MOUNTING POST CAP FRONT RAIL BRACKET COVER (2) TAPE (3 PLACES) GLAZING GASKET CURVED GLASS TOWER COVER GLAZING GASKET (2) TOWER MOUNTING BOLT & WASHER SELF DRILLING SCREW BASE 15 3 SCREWS AND 3 WALL ANCHORS 3 WALL BASE INSTALLATION PRELIMINARY ROUGH-IN INSTALLATION INSTRUCTIONS The floor structure beneath the unit must be able to support a total weight of the unit and bather. Refer to the table under total weight. STEP 1 Provide an opening in the subfloor no less than 5" x 5" square. This opening should be located on the center lines of the shower base drain hole (See Product Chart). The opening is to accommodate a 2" waste pipe. The waste pipe should be 1/4" to 1/2" above the surface of the subfloor. STEP 2 Remove the stainless steel strainer from the drain assembly. Disassemble the locknut and two gaskets from the back of the drain assembly. Apply a 1/4" bead of caulking (silicone) to the drain hole and insert the drain assembly. Replace the rubber washer, fiber washer, and lock nut in that order. Hand tighten the locknut. Remove excess sealant from finished side. Apply a lubricant (common household liquid soap works well) to the inside of the rubber seal of the drain assembly. STRAINER APPLY LUBRICANT DRAIN ASSEMBLY SHOWER BASE 90° 90° SILICONE SEALANT RUBBER WASHER 2" WASTE PIPE 5"x5" OPENING (MIN. AS POSSIBLE) FIBER WASHER As shown in top view, 1/2" copper pipes are provided to connect to the water supply. Also provided are 2 loose 45° elbows as shown for installation in Detail 1. NUT STEP 3 If the subfloor is level, no other preparation is necessary. You can proceed to install the shower base. If the subfloor is not level, level shower base by spreading floor leveling compound, mortar, plaster or minimal expansion structural foam with a minimum density of 5 lbs./cubic feet EVENLY over ENTIRE area where base will be installed. The compound used MUST make contact with the entire bottom surface of the base. Both sides of a joint or splice of subfloor should be level to each other. Level and support waste pipe cutout area greater than 5" x 5". The base is NOT to be supported by the tile flange. CAUTION: A nonflammable protective barrier must be placed between soldering work and base unit to prevent damage to the base. When connecting the supply lines, the toe plate can be notched to accommodate the pipes. The pipe under the base can be cut to length. To do so, remove the pipe clamps under the base, cut the pipe and reinstall pipes. STUD WALL NOT PROVIDED 45° ELBOW PROVIDED (2) DEATAIL 1 SPREAD MORTAR OR LEVELING COMPOUND ETC. EVENLY OVER ENTIRE AREA 16 3 WALL BASE INSTALLATION STEP 4 With the drain fitting passing over the center of the drainpipe, lower the shower base carefully into place, push down firmly until the base is in place. You must check the level of the base in two directions. Do not lift a corner to level the base. This will cause a loss of contact with the mortar. Attach the shower base flange to the stud wall and blocking with self-drilling screws (included). Use a minimum of 3 screws per flange section. STEP 5 With a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal the drain pipe connection. After drain is fully installed, test for proper drainage. If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath is not responsible for removal and/ or reinstallation costs. NOTE: Watertight installation of the drain is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty. Replace the strainer and tape over the drain hole to prevent finishing material from entering drain. WHEN SCREWING FLANGE TO STUD WALL START WITH THIS SIDE TIGHTEN SEALING NUT TOOL (INCLUDED) POSITION BASE OVER CENTER OF DRAIN PIPE AND SET INTO PLACE NOTE: If there is any gap between base flange and stud or blocking, shims MUST be used to prevent distortion or cracking of the flange. TILE FLANGE SHIM TILE FLANGE GAP USE SCREWS (PROVIDED) USE SCREWS (PROVIDED) STUD STUD INCORRECT CORRECT 17 3 WALL BASE INSTALLATION STEP 6 With the drain fitting passing over the center of the drainpipe, lower the shower base carefully into place, push down firmly until the base is in place. You must check the level of the base in two directions. Do not lift a corner to level the base. This will cause a loss of contact with the mortar. Attach the shower base flange to the stud wall and blocking with self-drilling screws (included). Use a minimum of 3 screws per flange section. STEP 7 With a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal the drain pipe connection. After drain is fully installed, test for proper drainage. If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath is not responsible for removal and/ or reinstallation costs. NOTE: Watertight installation of the drain is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty. Replace the strainer and tape over the drain hole to prevent finishing material from entering drain. CEMENT BOARD TILE CEMENT BOARD STUD STUD GROUT SILICONE SEALANT SHIM IF NECESSARY DO NOT FILL NOTE: If there is any gap between base flange and stud or blocking, shims MUST be used to prevent distortion or cracking of the flange. 1-1/8" MAXIMUM NO MINIMUM CLEAN-UP AFTER INSTALLATION To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent and warm water clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge. Paint, tar, or other difficult stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper. You can restore the glossy finish to the acrylic surface of the base with a special compound, Meguiar’s #10 Mirror Glaze. If not available, use automotive rubbing compound followed by an application of automotive paste wax. Major scratches and gouges which penetrate the acrylic surface require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for special instructions. SILICONE SEALANT 1/4" MINIMUM GAP TILE 1/4" MINIMUM GAP CEMENT BOARD TILE ADHESIVE SILICONE SEALANT STUD 1/8" GAP 18 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 3 Slide the glass panel into the wall post. Make sure that the corner notch is positioned toward the base of the tower. STEP 1 Position the wall post so the edge of the post is set back 3/4" (19 mm) in from the finish wall. FINISH WALL 3/4" (19 mm) STEP 2 Level the post in its proper position and mark where screw holes are to be drilled. Drill 3/16" holes and secure with wall anchors and screws provided. Cut a 12" strip of tape (provided) and apply firmly over screw heads. NOTCH STEP 4 Place the tower onto base. Ensure the curved glass locates into the glazing channel. Install bolt but do not tighten. TAPE 3 PLACES) BOLT (5/16") WASHER GLAZING CHANNEL 19 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 7 Place the front rail and tower support rail against the walls. Check level and mark the position for the rail mounting bracket. The screw position will be above the rail. Drill the wall with a 3/16" bit and secure bracket with screws and wall anchors provided. STEP 5 Insert support rails into brackets in top moulding of tower but do not tighten at this time. TOWER SUPPORT RAIL ATTACH RAIL BRACKET TO WALL FRONT RAIL SECURE RAIL TO BRACKET (TURN CW TO TIGHTEN) STEP 6 Slide mounting bracket covers and mounting brackets onto front rail and tower support rail. RAIL MOVE COVER CAP OVER BRACKET MOUNTING BRACKET COVER STEP 8 Adjust the rails until tower is vertical in 2 planes. RAIL WALL MOUNTING BRACKET 20 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 9 Secure the rails. STEP 11 Install cover cap on wall post. COVER CAP STEP 10 Tighten the tower base bolt. Two shut-off valves are provided. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw valve to stub outs at bottom of tower. Then reconnect braided line using provided gasket. Do not twist or kink supply lines when connecting. STEP 12 Install glazing gasket on curved glass wall post on the outside. Note orientation of gasket. Soapy water may help to insert the glazing gasket. On the inside of enclosure, apply sealant the entire length of glass and wall post as well as the entire length of glass and tower. SHUT OFF VALVES (PROVIDED) GLASS COLD WALL POST BOLT INSIDE OF ENCLOSURE HOT GLAZING GASKET APPLY SEALANT GLAZING GASKET TOWER TOP PLATE APPLY SEALANT 21 INSIDE OF ENCLOSURE 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 13 Turn on water supply and check for leaks. Correct any leaks before installing tower cover. STEP 15 Seal all around the base of tower with silicone sealant. Also seal the inside of both wall posts, bottom of both glass panels on the inside only. STEP 14 Install tower cover as shown. Insert cover at top first. APPLY SEALANT ALONG BASE OF GLASS TOWER TOP PLATE TOWER COVER APPLY SEALANT APPLY SEALANT ALL AROUND ALONG BASE TOWER BASE AND SIDE OF WALL POST INSERT THIS SIDE FIRST TOWER COVER (RAILS NOT SHOWN) TOP VIEW 22 2 & 3 WALL OPERATION Shower Head There are four selectable positions: Jet, normal pulsating and aerated flow. Body Sprays (2 Upper & 2 Lower) To adjust the flow and intensity, turn as shown. The spray can also be turned to change the direction of the spray. LESS FLOW AND INTENSITY MORE FLOW AND INTENSITY STOP RELEASE Diverter Control To turn On water, turn the inner knob clockwise and adjust for more or less flow. The outer knob will divert the water to body sprays, shower head (shown in this position) and foot temperature tester. If the knob is pointing anywhere between main functions, the amount of water will be proportional to where the knob is pointing. If the knob is pointing to the white line between positions, the water will be diverted equally to both functions on either side of the white line. SHOWER HEAD BODY SPRAY OUTER KNOB FOOT TEMPERATURE TESTER INNER KNOB Temperature Valve The temperature of the mixed water is adjusted by means of the graduated handle. This handle has a safety stop set at 100°F (38°C). To increase the temperature, press the red button to release the stop and keep turning the handle. Foot Temperature Testor 23 2 & 3 WALL MAINTENANCE To remove any lime scale from the shower head and body sprays , rub with your finger the outer ring of nozzles on the shower head and all nozzles on the body spray. To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools (such as scissors or screwdrivers, etc.) to clean the body sprays, shower head or foot temperature tester. To cleanthe base, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable. The glass can be cleaned with any glass-cleaning product available on the market. Do not use abrasives, alcohol, acetone, ammonia or other solvents on any tower component. The thermostatic valve has 2 screen filters that should be cleaned periodically. To remove the filters turn off hot and cold supplies. Remove tower cover. Disconnect the supply hoses from the valve and remove filter from the hose. Clean any debris. Reinstallation is the reverse of removal. Turn on hot and cold supply and check for leaks. Authorized Service If you need a referral for a service company near you, or need assistance with operation or maintenance related questions, please call our Service Support Department at 1-800-288-4002. For service agent listing, visit our web site at http://www.jacuzzi.com/. To find the service agent listings, click on “For The Trade”. Then click on Electrical/ Mechanical Service Agents. Depending on the problem, click on “Electrical/Mechanical Repairs” or “Finish, Surface or Shell-Related Problems”. PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance. Jacuzzi Whirlpool Bath P.O. Box 702168, Dallas, TX 75370-2168 Service Support: Call (800) 288-4002 © 2002 Jacuzzi Whirlpool Bath U223000 8/13/04 Printed on Recycled Paper Printed in U.S.A. 24 TOWER FIXTURES REPAIR PARTS 1 (5X) 2 (5X) 3 (5X) TOWER ASSEMBLY 4 9 (5X) 6 10 5 11 (4X) 7 (Part of U547000) 8 12 13 14 15 16 17 18 PART OF D709827 WASHER (PART OF D709827) 19 1. C546000 Lock Nut, 1/2" NPT WP (5X) 2. G559000 Ring Compression SS (5X) 3. G560000 Washer Rubber (5X) 4. U546000 (Part of U547000) Nut Transfer Valve, Chrome 5. U566000 Gasket, 1.41 ID X .063 Thick 6. U547000 Valve, Mixer/Transfer Assembly 7. U550827 (Part of U547000) 567000Nut, Mixer Valve, Chrome 8. U567000 Gasket, 1.9 ID X .063 Thick 9. G432000 Nipple,1/2" Close 10. U217827 Shower Head, Chrome 11. U215827 Jet, Wall Body, Chrome 12. U219827 Face Plate, Transfer Valve, Chrome 13. U546827 Nut Transfer Valve, Chrome 14. U545827 Collar, Transfer Valve, Chrome 15. U544000 O-Ring, Transfer Valve 16. U543827 Knob, Flow Control, Chrome 17. U549827 Collar, Mixer Valve, Chrome 18. U548827 Knob, Mixer Valve Chrome 19. D709827 Fill Spout Assembly, Stubby, Chrome 25 TOWER PLUMBING REPAIR PARTS 1. A944000 (9X) Spring Clamp, .625 OD Hose 2. U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb 3. U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb 4. A945000 (7X) Spring Clip, .75 OD Hose 5. U400000 FTG, Straight, 1/2" FTS X 10mm Barb 6. U403000 (2X) Cap, 1/2" FST 7. U711000 (2X) Strainer Washer, 1/2" Dia. 8. U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb 9. U540000 (2X) 1/2" Flexhose 38", Female Swivel Heads 10. GASKET (2X) Gaskets Supplied with Hose 11. U827000 (2X) Ball Valve, .5 FTP X .5 MPT L 12. U421000 (11X) Washer, FTG .7 OD 13. U401000 (7X) FTG, Ell, 1/2" FST X 10mm Barb 14. U405000 L=4.5" Tubing, PVC Reinforced, 10mm Barb 15. U404000 (2X) FTG, Y, 10mm X 10mm X 10mm Barb 16. U405000 L=2.5" Tubing, PVC Reinforced, 10mm Barb 17. U402000 FTG, Tee, 1/2" FST X 10mm Barb 18. U405000 L=10.0" Tubing, PVC Reinforced, 10mm Barb 19. U405000 L=4.5" Tubing, PVC Reinforced, 10mm Barb 20. U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb 1 (9X) See Note 1 2 12 (11X) 13 (7X) 3 14 4 (7X) See Note 2 15 (2X) 5 16 17 Note 1: For Clamping U405000 to U401000 or U402000. Note 2: For Clmping U405000 to U400000 or U404000. 18 6 7 19 8 9 (2X) 20 10 (2X) 11 26 2 WALL UNIT REPAIR PARTS 5 (2X) 6 (2X) 4 1 3 7 (6X) 2 8 11 12 9 10 14 (6X) 13 (6X) 17 18 15 U134827 Rail Back Walk-in 16 U133827 Rail 2 Wall Walk-in U245827 Rail Assembly Walk-in U149000 Bracket, Mounting Rail U119827 Wall Post, Panel U138827 Cap, Wall Post J686000 Tape High Bond, 2 Sided U159000 Gasket,Vinyl, Glass Panel U479XXX Glass Panel Assembly, Walk-in U124XXX Tower Cover U257XXX Final Shell, Tower Walk-in U126XXX Tower Body Walk-in U136XXX Cap, Top, Tower U137XXX Cap, Bottom, Tower U149000 Bracket, Mounting Rail U354000 Screw, Self Tap, #8-1.25" L U355000 Screw, Self Tap, #8-2.0" L 12. U113000 Glass Panel, Front, Wlak-in 13. U354000 Screw Self Tap #8 X 1.25" L 14. U703000 Anchor, #6-8-10 15. 5374832 Screw, Sheet Metal PHP, #6 X .88" L 16. U196000 Bracket Corner Post, Bottom 17. 3952832 Bolt Hex FL Thrd 5/16 18. 3983832 Washer 5/16 Flat Type A Plnwdser 19. U247000 Gasket,Vinyl, Glass Panel 20. U174XXX Shower base Walk-in 2 Wall 21. U220000 Screw Self Drilling, #8 X 1.63" L 22 9959000 Drain, Non-Caulk 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 19 (Used with Tower with Timber Finish Only) 20 For finishes for U124XXX Tower Cover and U257XXX Tower Final Shell substitute XXX for: 801 Satin 827 Chrome 938 Timber 959 White 27 21 22 For colors for U174XXX Shower Base substitute XXX for: Standard 959 White 958 Almond 969 Oyster 945 Silver High Fashion 917 Black 949 Rose 951 Shell 978 Forest Green 984 Shy Blue 999 Sand 3 WALL UNIT REPAIR PARTS 5 1 2 3 (2X) 4 10 7 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 8 (2X) 9 U134827 Rail Back Walk-in 3 Wall 6 U245827 Rail Assembly Walk-in 3 Wall U149000 Bracket, Mounting Rail U119827 Wall Post, Panel U138827 Cap, Wall Post U124XXX Tower Cover U257XXX Final Shell, Tower, Walk-in 3-Wall U126XXX Tower Body Walk-in U136XXX Cap, Top Tower U137XXX Cap, Bottom, Tower U149000 Bracket, Mounting Rail U354000 Screw, Self Tap,#8-1.25" L U355000 Screw, Self Tap,#8-2.0" L U247000 Gasket,Vinyl, Glass Panel U113000 Glass, Panel, Front, Walk-in U159000 Gasket,Vinyl, Glass Panel J686000 Tape, High Bond, 2-Sided U354000 Screw Self Tap, #8-1.25" L U703000 Anchor, #6-8-10 3952832 Bolt Full Thread, 5/16 3983832 Washer, 5/16, Flat, Type 2 Plnwser U171XXX Shower base, Walk-in, 3-Wall U220000 Screw Self Drilling, #8 X 1.63" L 9959000 Drain, Non-Caulk For finishes for U124XXX Tower Cover and U257XXX Tower Final Shell substitute XXX for: 801 Satin 827 Chrome 938 Timber 959 White For colors for U171XXX Shower Base substitute XXX for: Standard 959 White 958 Almond 969 Oyster 945 Silver High Fashion 917 Black 949 Rose 951 Shell 978 Forest Green 984 Shy Blue 999 Sand 11 12 17 (10X) 14 15 18 16 28 13 Jacuzzi Whirlpool Bath Limited Warranty Designer Collection Shower Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions. TWO YEAR LIMITED WARRANTY ON BATHS Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed components against defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user. NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers options and accessories manufactured by the Company against defects of material or workmanship. Warranty coverage begins on the date the option or accessory was originally purchased by the user. WARRANTY LIMITATIONS Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from, without limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason (including modification to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incorrect operation, or lack of proper routine maintenance; operation of the unit without specified minimum amount of water or at inappropriate water temperature; use of abrasive or improper cleaners; or acts of God, such as lightning, floods, earthquakes, etc. In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause (e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool and/or spa chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company; the unit's prior usage as an operational display; or defects that should have been discovered before installation. This limited warranty does not include: labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement unit; any costs relating to obtaining access for repair; or loss of use damage, including loss of sales, profit or business advantage of any kind under any circumstances. Bath units are excluded from any warranty coverage if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to any component). Warranty coverage is provided in the United States of America and Canada. EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO THE FULL EXTENT ALLOWED BY LAW. NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished by the Company. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. RETURN OF WARRANTY CARD The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi Whirlpool Bath in order for this warranty to become effective. Jacuzzi Whirlpool Bath P.O. Box 702168 Dallas, TX 75370-2168 RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper inspection and testing prior to installation. Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered. If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter. It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating to obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer. Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the responsibility of the user. Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company are warranted for ninety (90) days from the original date of purchase for parts only.) The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements at the time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes in U.S.A. or municipal or provincial codes in Canada. WARRANTY SERVICE For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are not agents or representatives of the Company and cannot bind the Company by words or conduct. The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user. In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent. Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service. If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write: Jacuzzi Whirlpool Bath Warranty Service Department P.O. Box 702168 Dallas, TX 75370-2168 Call: (800) 288-4002 To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company, call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where to return, at your expense, the failed component(s), option(s), or accessory(ies). All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced. The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates the Company's warranty obligation. ©2002 Jacuzzi Whirlpool Bath U223000 8/13/04 Ninety-Day Parts Only Limited Warranty On Accessory(ies) Warranty Registration Card Purchaser's Address _______________________________________ This card must be filled out and returned to the address printed on the other side within thirty (30) days from date of purchase in order for this warranty to be come effective. Purchaser's Name ________________________________________ Date of Purchase _________________________________________ City _____________________________ State _____ Zip ________ Serial Number ___________________________________________ Model Name _____________________________________________ Dealer's Address __________________________________________ Dealer's Name ___________________________________________ 1. How did you first hear about this Jacuzzi® product? ( ) Article in Magazine/Newspaper ( ) Advertisement ( ) Yellow Pages ( ) Visited Dealer/Plumbing Supplier ( ) Decorator/Architect ( ) Builder/Plumber/Remodeler ( ) Visited Retailer/Home Center Store ( ) Word of Mouth . . . Friend/Relative/Acquaintance ( ) Other (Please Describe) _______________________________ 2. Who first gave you specific information about this product (specifications, prices, etc.)? ( ) Remodeler ( ) Builder ( ) Dealer/Plumbing Supplier ( ) Retailer/Home Center Store ( ) Plumbing Contractor ( ) Already Installed ( ) Decorator/Architect 3. What was the main reason for purchase? ( ) Product Features ( ) Warranty Service ( ) Styling ( ) Hydrotherapy ( ) Price ( ) Brand Name ( ) Home Resale _______________________________________ ( ) Other _____________________________________________ 4. Who finally decided which product you would buy? ( ) Self and Spouse Together ( ) Spouse ( ) Self ( ) Designer/Architect ( ) Other Family Member ( ) Already Installed ( ) Builder/Plumber/Remodeler ( ) Already installed/New Home 5. Who installed? ( ) Contractor/Plumber when remodeling ( ) Self/Spouse when remodeling ( ) Other _____________________________________________ 6. What is the current market value of this property? Please estimate $ _______________________________________ 7. What is the age of the head of the household? _____________ years 8. What other manufacturers did you consider? ( ) Aqua Glass ( ) Lasco ( ) Price Pfister ( ) Eljer ( ) Sterling ( ) American Standard ( ) Kohler ( ) Other (Specify) _____________________________________ 9. How long did you shop before purchasing unit? ( ) 2 months-6 months ( ) 1 day ( ) 6 months-1year ( ) 2-7 days ( ) 1 year-2 years ( ) 1 week-2 weeks ( ) +2 years ( ) 2 weeks-4 weeks ( ) 1 month-2 months 10. Approximately how long have you lived in this home? ___________ 11. Please indicate, approximately, the total annual income of your household. ( ) $50,000 to $74,999 ( ) Up to $24,999 ( ) $75,000 to $99,999 ( ) $25,000 to $29,999 ( ) $100,000 to $149,999 ( ) $30,000 to $39,999 ( ) $150,000 and Above ( ) $40,000 to $49,999 12. Was your purchase process? ( ) Very Difficult ( ) Difficult ( ) Very easy ( ) Easy 13. How technically aware were you of the patented Jacuzzi® jet system prior to your puchase? ( ) Not aware ( ) Somewhat aware ( ) Very aware Ninety-Day Parts Only Limited Warranty On Accessory(ies) U223000 8/13/04
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021