Numark Industries DM900EX DJ Equipment Owner's Manual

Professional Disc Jockey Products

DM 1885X STEREO MIXER

OWNER’S MANUAL

NUMARK INDUSTRIES

11 Helmsman Road, North Kingstown RI 02852

http://www.numark.com

DM1885X

Numark - The Proven Leader in DJ Technology

©1997 Numark Industries

2 http://www.numark.com

DM1885X

CAUTION

6. Heat - Avoid placing this product too close to any high heat sources such as radiators.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE ANY COVER. NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL ONLY.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

7. Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit.

8. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.

The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this appliance.

CAUTION

FOR USA & CANADIAN MODELS ONLY

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS

(POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE

OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE EXPOSURE.

9. Object and Liquid Entry - Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer.

10. Damage Requiring Service - This product should be serviced only by qualified personnel.

If you have any questions about service please contact Numark at the number(s) shown on the back cover of this manual.

11. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means built into the mixer is not defeated.

SAFETY INSTRUCTIONS

1. Read Instructions - All the safety and operating instructions should be read before this product is connected and used.

12. Internal/External Voltage Selectors - Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. Do not attempt to alter this yourself.

2. Retain Instructions - The safety and operating instructions should be kept for future reference.

3. Heed Warnings - All warnings on this product and in these operating instructions should be followed.

NOTE: This apparatus does not exceed the

Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of

Communications.

4. Follow Instructions - All operating and other instructions should be followed.

5. Water and Moisture - This product should be kept away from direct contact with liquids.

WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.

Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom you purchased the unit. Retain this information for your records. Please return the warranty card enclosed to register your mixer with us.

MODEL: DM1885X PURCHASED FROM:_________________________

SERIAL NUMBER:__________________ DATE OF PURCHASE:________________________




DM1885X

NUMARK DM1885X STEREO MIXER

INDEX

Safety Information

Product Registration

Introduction and Features

Precautions

Front Panel Diagram

Sampler Operation

Page 3

Page 5

Page 7

Page 8

Page 10

Rear Panel Diagram Page 12

Connection Instructions and Diagram Page 13

Specifications

Block Diagram

Warranty and Service

Page 14

Page 15

Page 16




DM1885X

CONGRATULATIONS!

You have purchased the D M 1 8 8 5 X Stereo Mixer by Numark. This equipment features the latestest in sampling technology. With all new circuitry you get 4 assignable memory banks and editable sampling capability. You also get high quality audio output and better reliability than ever before. TheDM1885X Preamp Mixer has been designed by

DJs for DJs. It gives you all of the controls and features you need in a professional piece of equipment to dazzle the crowd.

Thank you for buying Numark DJ products!

FEATURES...

• User replaceable assignable ALPs™ crossfader .

• Bass, Mid,Treble,and Gain controls on every input channel.

• Left<->Right Pan control on each channel and the DJ Mic.

• Bass, Mid & Treble “KILL” switches for special effects and creative mixing.

•

Neutrik™ “Combo” connector allows 1/4” or XLR plug to be used for DJ Mic.

• 8 line inputs.

• Three phono inputs switchable to line level.

• Sends on each channel for easily hooking up external effects.

• Pushbutton Cueing with PFL (pre-fader listen) on each channel.

• Headphone monitoring with PFL/Program fader.

• Master and 2 Zone outputs.

• Stereo/Mono switch on the Master and Zones.

• Balanced Outputs.

• Tape Out for direct recording.

• Powerful stereo headphone output.

• High-end performance audio signal.

• 12V BNC light connector.

Digital Sampler features:

• Advanced Digital Processor by “Analog

Devices” and DRAM memory provides true 16bit CD quality audio and powerful recording, editing and playback options.

• Re-triggering for stuttering “rap”-style effects.

• Effect Level Fader.

• Large Start-Stop button.

•Digital processor modes:

-E d i t

(allows Intro and/or Outro trimming of the sample after it is recorded).

-S i n g l e

(sample plays once).

-R e p e a t

(loops sample until disengaged).

-S t u t t e r

(for "stutters" and "stabs" in single or repeat mode).

-Speed Control ( plays sample faster or slower than originally recorded resulting in frequency shift).

-Monitor

(for monitoring sample with or without program or cue audio output).

-Write

(safely record a sample).




DM 1885X

As a special bonus we have

included a right angle headhpone

adapter with this mixer.

Just plug your headphones into

the adapter and then plug the

adapter into your mixer.




DM1885X

IMPORTANT INFORMATION...

Please read this entire manual before connecting the DM1885X to your system.

For optimum performance:

• Always make sure that AC power is OFF while making any connections.

• Do not use excessively long cables (i.e.

over 50ft/14m) Be sure plugs and jacks are tightly mated. Loose connections can cause hum, noise or intermittents that could easily damage your speakers.

• Never use spray cleaners on the slide controls. Residues cause excessive dirt buildup and this will void your warranty. In normal use slide controls can last for many years. If they malfunction (usually because of a dirty or dusty environment) consult a professional technician.

• Never attempt to make any adjustments or repairs other than those described in this manual. Take the DM1885X to your dealer or to an authorized Numark Service Center.

A NOTE ON CABLES:

Make the input and output connections with readily available low-capacitance stereo cables. Quality cable makes a

big difference in audio fidelity and punch. Use balanced connections whenever possible. See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get.

SYSTEM PRECAUTIONS

• Use appropriate cables throughout your system: Quality shielded audio cables and terminated shielded video cables, lowcapacitance preferred. Speaker cables must be

14-gauge minimum; 12- or 10-gauge is better.

• Reliability will be enhanced through the use of banana connectors on the speaker wires.

Observe correct speaker wire polarity. If in doubt, consult your Numark dealer or a qualified technician.

• Take care to connect only one cable at a time. Pay attention to the color-coded, labelled

Input and Output jacks.

• ALWAYS remember: “TURN AMPS O N

LAST AND OFF FIRST”. Begin with master faders or volume controls on minimum and the amplifier gain/input control(s) down. Wait 8 to 10 seconds before turning up the volume. This prevents transients which may cause severe speaker damage.

• Use restraint when operating controls. Try to move them slowly. Rapid adjustments could damage speakers due to amplifier clipping.

• Avoid amplifier “clipping” at all costs: this occurs when the red LEDs (usually on the front panel of most professional power amplifiers) start flashing. “Clipping” is when the power amplifier is distorting and working beyond it’s limits. Amplifier distortion is THE major cause of speaker failure.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture. Never

place cans of beer, soda, glasses of water or anything wet on top of the mixer!




DM 1885X

DM1885X FRONT PANEL DIAGRAM...

23

1

5

3

6

7

2

4

8

11

9

10

15

1. Channel Input Gain/Trim/Attenuation Controls.

These control the sensitivity of the inputs for Channels 1-4.

Use these whenever a particular source causes overload of the preamp inputs. Attenuation range is 0dB to -20dB. Use these with the PFL (pre-fader listen) monitor when cueing.

2. Treble, Middle and Bass Controls fine tune the tone of your music through the sound system. Note that these are also available on the DJ Mic.

3.Use the Pan Control to maximize the Left or Right side of your Source.

4. S e n d button will send the individual channel signal to the onboard sampler and the send jack on the rear panel. This is used to route to an external effects unit. The signal comes back in from the effects unit through any line input channel you select and is then sent out to your amplifier through the

Master Output jacks on the rear panel.

22 21

17

18

16

12

19

20

25

29

26

27

13

31

32

14

28

30

5. DJ Mic Talkover Switchhen engaged this mutes your music sources from channels 1-4. Releasing it brings you immediately back to full source level. It is very useful for announcements.

6. Channels 1 - 4 Input Toggle Switches select which source will be live to that channel based on what you have connected to the rear panel input section.

7.The Input Faders are low-noise, low-impedance, highquality, smooth faders. These control individual source levels in the mix.

8. Channel Cue Assign/PFL pushbuttons are used to route channel audio to the Monitor Section. The channel input faders do not control the C u e volume. When the Cue button is pushed you get Pre Fader Listen(PFL). In addition, when these buttons are depressed the third row of the LED meter (20) will display the signal level of that channel on a

PFL basis. The level can be adjusted by using the G a i n

control (1).




9. The Crossfader In/Out Pushbutton defeats the entire Crossfader function but leaves the Kill functions active.

10. Crossfader/Kill Assign Switches lets you choose which input channel will be heard when the Crossfader is moved to the left or right and affected by the Kill function.

11.The replaceable Crossfader achieves clean segues between two selected input channels.

1 2 3 4 1 2 3 4

In this example, Channel 1 is selected on the Left and

Channel 3 is selected on the Right. With the Crossfader centered both assigned channels are live. Use the

Crossfader for fast and seamless segues from one channel to the next.

N o t e : the crossfader is user replaceable. Simply unscrew the two large screws which hold it in place, lift it out, and disconnect its cable. Reattach the new crossfader and screw it back onto the unit - you’re back in business!

REPLACEMENT CROSSFADERS can be purchased from your local Numark Dealer, or by calling Numark Industries.

12.The Cue Crossfader controls what signal is being monitored through your headphones. Move the slide control to the left and you will hear your source music from the channel(s) selected with the cue/PFL switch. Move the control to the right and you will hear your program mix, or output. The slide control allows fast and frequent headphone monitoring.

13.The Headphone Level control sets the volume in your headphones.

14.The Headphone Jack accepts a 1/4” plug and is set on the front of the unit.

15. Kill Switches and LEDs have been provided for

Treble, Mid and Bass Control on each side of the crossfader. This allows you to mute that frequency’s audio

DM1885X

output while leaving the other frequencies playing. This area is always active even when the crossfader is not. Try that for

a neat effect, or mix one channel’s treble with another channel’s bass (by cutting the mid and bass on the first channel and the treble and mid on the other channel.)

16. M a s t e r L e v e l. This controls overall output level. Note that you can select (18) whether you want stereo or mono.

17. The Zone Levels control speaker volume for other outputs such as control booth monitors, a tape deck, another amplifier, a sub-woofer, another mixer or a satellite speaker system. Note that you can select (18) whether you want stereo or mono.

CONTRACTOR'S NOTE: Zone Level provides zone control in installations where there are two separate rooms

(eg: a bar and a dance floor). The “Zone” volume should be controlled from the mixer not from the amplifier.

18. The Stereo/Mono Toggle Switches allow you to select either stereo or mono output.

19. Stereo Auto Peak Hold Level Meter. The red LEDs for

+3, +5 and +8dB hold program peaks for an instant.

With peak metering, it's OK to be "in the red" as long as +5 or

+8dB isn't constantly lit. Set crossover, equalizer and power amplifier inputs to avoid distortion at each step in the audio chain. Proper attention to the peak meters results in the punchiest possible sound without audible distortion.

20. PFL Meter. When the Cue/PFL switches are depressed this meter tracks pre-fader listen (PFL) signal for the channel selected instead of the mixer’s output level.

21. 12V BNC Connector allows a 12 volt gooseneck style

“Numark” light to be connected directly to the mixer.

22. The Power button turns the unit on and off. Make sure your input faders (7) are turned down before you power up your mixer.

23. The M i c J a c k is a Neutrik™ “Combo Jack” and allows connection of either a 1/4” jack or an XLR jack. This is ideal for connecting an XLR Gooseneck directly.




DM 1885X

DIGITAL SAMPLER SECTION TO RECORD A SAMPLE

The Sampler uses dynamic RAM with a 16-bit microprocessor controller. The same digital signal processing components used in professional audio equipment deliver CD-quality samples.

25. The Mode Pushbuttons switch from effect to effect. The accompanying LEDs illuminate to show you which specific mode you are in at any time.

Modes are: a - Press the Write button once to go into stand by mode. The red LED will go on.

b - Select the bank (or multiple banks) into which you want to record. Any bank can be selected. Each bank contains 3 seconds of recording time. If you want to record a longer sample select multiple banks (they must be adjoining). To playback a multi-bank sample you must reselect the same banks later. N o t e : To overwrite an existing sample, select that bank instead of an empty bank. Changing bank selection at this point in time is possible and will not destroy any previously recorded samples.

• R e p e a t sets the unit to play back a sample and automatically repeat (loop) when it gets to the end of the sample.

e - Hit the Start-Stop button to begin recording. It's red LED will light.

• Single sets the unit to play back a sample once.

• Edit sets the unit to sample edit. This activates the

Intro and O u t r o editing controls as described in

#26. Edit can be used at the same time as S i n g l e and R e p e a t so that editing of the sample can be done while your program output is playing on the dance floor.

f - Hit Start-Stop a second time to stop the sampling, or allow the memory banks to fill up, at which time sampling will stop automatically. Once your writing is complete the sampler will automatically switch to Single playback mode and light the Single LED. The sampler is now ready for playback.

• Write sets the unit to sampler record ready.

Depress the appropriate send button for the channel you wish to record. Selecting a bank to record to and hit the Start/Stop button (#30) to begin recording

(it is safer to actually choose your bank before going to write mode so that you don't accidentally wipe out an existing sample). The LED will stay lit while you are in Write mode. After you are done writing your sample you should select a play mode (either Single or Loop) and listen to your sample - note that you must do this manually by hitting the correct Mode

Pushbutton.

26. Intro and Outro editing controls are used when E d i t mode is selected to fine tune the beginning (Intro) or ending (O u t r o) of your samples. These "trim" the unwanted sound while in S i n g l e or R e p e a t playback modes. Turn the controls inward to trim more - return them to their full outside position to return to your full sample.

Once trimmed turn E d i t off to lock-in your settings, now every time you select the sample it will be the perfect length. N o t e : Trimmed samples are not erased - they can be heard again by going back into E d i t and undoing the trim. This powerful new feature allows you to start a sample early or end it late and still trim it to the perfect length without having to re-record. Since these controls can be active while the sample is "live", you can even fine tune samples on the fly. A way of efficiently trimming samples is by engaging the S t u t t e r button and repeatedly hitting the

Start-Stop button as you adjust the Intro knob.




DM1885X

27. The Speed Control plays samples faster or slower resulting in a pitch shift of the sample. In the center position, the sample is played at recorded speed. Moving the knob to the left will slow down playback by up to 50%; moving the knob to the right will speed up the playback by up to 200%. Positions near the center provide fine changes in playback speed. Positions further from the center detent provide more drastic changes in playback speed.

• In S i n g l e or R e p e a t play with Trigger you are ready to "stab" samples. With the Trigger Out, the sample plays all the way through before you can play it again. With it In, you can stab or stutter a sample.

When you shout "Rock it - rock the house!" and sample it, it can be played back as -

R-R-R-R-R-R-R-Rock --

Rock-Rock-Rock it - Rock it Rock it -

Rock - - Rock it - rock the house!

28. Effect Level Mix fader. This precisely sets the audible level of the sample in the mix.

by simply "drumming" with your fingers.

29. Memory Bank Select Pushbuttons A-D. Four banks are available for storing samples. To record a bank go to Write and then hit the bank button. You can record into any combination of banks by pressing multiple bank buttons.

After sampling, you can either select the next bank and record it (remember Write is still on, just select the bank and hit Start/Stop) or you can manually select a playback mode.

31. The Stutter Pushbutton lets you choose between two playback styles, Trigger and Non-

Trigger, when in Single or R e p e a t modes.

• When the Stutter is Out and the sampler is set to

Single or R e p e a t mode, each time you tap the

Start-Stop button the sample starts to play. The next tap stops sample playback. The next time play starts, the sample re-starts at the beginning.

You can play any combination of the Memory Banks from left to right (that is, Memory Bank B will always play before

Memory Bank D - but you can play ABCD; BC; BD: ACD; only C; only D; etc.).

30. The large Start-Stop button controls sample recording and sample playback. The small red Effects Indicator LED glows when the sampler is "on". Here are the functions:

• When the Stutter is In and the sampler is set to

Single or Repeat mode, each time you tap the Start-

Stop button the sample re-triggers.

ABOUT STUTTERING

Expensive studio rack-mount samplers and sampling keyboards can re-trigger or stutter. This means

"beginning at the start of the sample each time a key is pressed or a drum pad is struck".

• Tap the button when in sampler Write mode to begin

sampling (the LED will light). Tapping it again ends the sample and the LED goes out. (unless the sampler has run out of memory and shuts off automatically - Once the

Effects Indicator LED goes out, the Write LED goes out and the Single LED turns on.

• In single or r e p e a t play without Trigger, tap the button to play the sample and tap it again to stop the playback.

Every time you play the sample, the music starts from the beginning of the sample.

Re-triggering creates the stuttering "rap" effect. The

D M 1 6 8 5 / 1 8 8 5 includes a manual stuttering feature. How fast can y o u tap? Try using two fingers for increased speed.

32. Monitor Pushbutton. To hear the sample or effect in the headphones, press this button.

Program Mix still works and you will be able to hear any other input channels with the C u e buttons activated.




DM 1885X

DM1885X REAR PANEL DIAGRAM...

10

11

1

8 8

4 2 3 5 7 7 7 9 7 9 7 9

12

6

1. The Balanced Main Outputs are low-impedance XLR type connectors controlled by the Master fader.

5. The S e n d can be attached to an external effects processor such as a sampler.

8. Line/Phono Input switch. Use this to allow line level equipment to be plugged into your phono inputs giving you a total of 8 line input options.

2. The Stereo Main Outputs are low-impedance RCA connectors controlled by the Master fader.

3. The Tape Outputs are low-impedance unbalanced RCA jacks which output the program mix and allow you to connect any recording device.

4. The Stereo Zone Outputs are low-impedance unbalanced RCA jacks controlled by the Z o n e L e v e l controls.

9. Phono Inputs on Channels 1, 2 and 3 use unbalanced RCA jacks. Your input signal is fed directly to the D M 1 8 8 5 X's high-quality RIAA phono preamplifiers so use this position only for moving magnet cartridges.

Line level sources will overload the sensitive phono preamps and will sound very bad, so always be sure to toggle the line/phono switch over to line before connection of line sources.

10. AC Cord. See safety precautions on page 3 for proper treatment of the power cord.

6. Mic is the mic input for the Mic Channel and Channel 4.

11. Voltage Selector. Set this for the appropriate voltage in your area

7. Channels 1-5 Line Inputs are unbalanced RCA jacks.

The Line Input is selected with the toggle switch on the

12. GND is the grounding lug for turntables 1, 2 and 3

(phono inputs on Channels 1, 2 and 3). Always use this front panel. You can connect stereo audio from HiFi

VCRs, cassette and reel-to-reel tape decks, DAT connection (your turntable cable should have a grounding wire).

machines, CD players, laser discs, tuners, even synthesizers or other mixing consoles.

N O T E : Plug mono audio sources into both Left and Right

inputs using a “Y” cable connector.




DM1885X Instructions for Connection and DIAGRAM...

Tape Deck

Zone 1

Sound System w/ Amplifier

Zone 2


Sampling

Keyboard

Turntable 1

DM1885X

AC

Outlet

Microphones

Tape Deck

Turntable 2

Main


CD Player

Dual CD Player

Turntable 3

1. Be sure the POWER (22) is OFF. All connections should be made before the unit is turned on. Always remember

“Turn Amps on last and off first!”

2. Use appropriate cables throughout your system: quality shielded audio cables, low capacitance preferred. Speaker cable must be 14-gauge minimum; 12- or 10-gauge is better.

3. Connect your music sources on the rear of the unit. Up to 3 phono and 8 line sources (CD players, cassette decks, tuners, etc.) can be connected. When connecting to an input with a phono/line option switch remember to set the switch accordingly.

4. Connect the ground wire from your turntables (and any other sources that come with a ground) to the ground post on the rear panel. This will eliminate most common hum and feedback problems.

5. Connect your DJ mic on the front left side of the unit (23) or on the back of the unit at Mic 1. Connect your second mic at

Mic 2 on the back of the unit.

6. Connect your headphones on the front right side of the unit at (14).

7. The OUTPUT MASTER jacks on the rear of the unit are for connecting to the amplifier. Use the balanced outputs if possible. Make sure you correctly attach the right and left cables to avoid phasing problems.




DM 1885X

SPECIFICATIONS...

I N P U T S :

Line: 10k

Ω

input impedance

Mic:

100 mV rms sensitivity (for 1.22 V output)

10k

Ω

input impedance balanced/unbalanced

3 mV rms sensitivity (for 1.22 V output)

50 mV rms max input

Phono: 47k

Ω

input impedance

1.5 mV rms sensitivity @ 1 KHz (for 1.22 V output)

S A M P L E R :

FREQUENCY RESPONSE AND SAMPLING RATE:

Variable sampling rate 44.1 kHz with 16-bit sampling yields

20Hz-22 kHz.

MAXIMUM MEMORY TIME:

12 seconds

O U T P U T S :

Line: 9V rms max (+20 dBm)

Headphone Amp: 5 watt into 47

Ω

Distortion less than .01%

SIGNAL TO NOISE RATIOS

(vs. maximum output):

Line: Better than 82 dB

Mic: Better than 75 dB

Phono: Better than 75 dB

F R E Q U E N C Y R E S P O N S E :

Mic:

Line:

Phono: +

@ 20 Hz to reduce rumble and feedback

C H A N N E L E Q :

Bass: ±15db @80Hz

Middle: ±10db @1KHz

Treble: ±15db @12.5KHz

TALKOVER ATTENUATION:

Variable from no cut to -16 dB

K I L L E F F E C T S :

Bass: -54dB at 50 Hz, -3dB at 400 Hz

Middle: -44dB at 1k Hz, -3dB at 200Hz

Treble: -53dB at 15k Hz, -3dB at 2k Hz

POWER CONSUMPTION:

20 Watt typical, 28 watt with full headphone output




BLOCK DIAGRAM...

DM1885X




Professional Disc Jockey Products

Warranty and Service Information

Numark Industries, LLC and Numark International, Inc. (hereafter “Numark”) warrants each new product manufactured and/or supplied by it to be free from defects in material or workmanship under conditions of normal use and service for 360 days, beginning on the date of purchase from an authorized Numark Dealer, but not to exceed 2 years from date of shipment by Numark.

The Numark obligation under this warranty is limited to repairing or replacing, at its option, the product or part(s) therein; which upon examination by Numark shall appear to be defective or not up to factory specifications; providing the Numark product is returned (transportation prepaid) to Numark.

Numark shall not be liable for any damages, consequential or otherwise, resulting from the use and operation of this product and makes no other warranty(s) either express or implied on this product, including any warranty of merchantability.

This warranty does not extend to any of our products which have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, or use in violation of instructions furnished by us, nor extended to units which have been repaired or altered outside of our factory, nor to cases where the serial number thereof has been removed, defaced, or changed, nor to accessories used therewith not of our own manufacture. Numark reserves the right to make changes or improvements in its products, during subsequent production, without incurring the obligation to install such changes or improvements on previously manufactured equipment.

To place this warranty into effect, the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries, LLC within thirty (30) days after date of purchase.This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state.Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

EQUIPMENT TRANSPORT

A Return Authorization number should be obtained from Numark through the addresses or phone numbers below.

It is the customer’s obligation, when returning faulty equipment, to properly pack the

Numark equipment in its original packaging. Failure to do so may inadequately protect the equipment in transit and, therefore, jeopardize the customer’s warranty. The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number to:

NUMARK INDUSTRIES

11 Helmsman Road

North Kinstown, RI 02852 USA

Attention: Service Department

Telephone: + 1 ( 4 0 1 ) 2 9 5 - 9 0 0 0

Fax:

E-mail:

+ 1 ( 4 0 1 ) 2 9 5 - 5 2 0 0 [email protected]

Numark Industries DM900EX DJ Equipment Owner's Manual

Professional Disc Jockey Products

DM 1885X STEREO MIXER

OWNER’S MANUAL

http://www.numark.com

SAFETY INSTRUCTIONS

NUMARK DM1885X STEREO MIXER

INDEX

Safety Information

Product Registration

Introduction and Features

Precautions

Front Panel Diagram

Sampler Operation

Page 3

Page 5

Page 7

Page 8

Page 10

Rear Panel Diagram Page 12

Connection Instructions and Diagram Page 13

Specifications

Block Diagram

Warranty and Service

Page 14

Page 15

Page 16

CONGRATULATIONS!

DJs for DJs. It gives you all of the controls and features you need in a professional piece of equipment to dazzle the crowd.

Thank you for buying Numark DJ products!

FEATURES...

Neutrik™ “Combo” connector allows 1/4” or XLR plug to be used for DJ Mic.

Digital Sampler features:

As a special bonus we have

included a right angle headhpone

adapter with this mixer.

Just plug your headphones into

the adapter and then plug the

adapter into your mixer.

IMPORTANT INFORMATION...

DM1885X FRONT PANEL DIAGRAM...

15

DM1885X REAR PANEL DIAGRAM...

DM1885X Instructions for Connection and DIAGRAM...

CD Player

SPECIFICATIONS...

BLOCK DIAGRAM...

Professional Disc Jockey Products

Warranty and Service Information

Related manuals

Numark Industries

DM1720X

Numark

DM2002X

Numark Industries

PA5Pro

Numark Industries

DM900EX

Numark Industries

DM1295

Numark Industries

DM1200

Numark Industries

DJ-24

Numark Industries

DM 1820X

Peavey

DSM 752

Numark Industries

EM360

Numark Industries

DM2000X