UPS
2348
+
Thermal Printer
Quick Start
Unpack Your Printer
Printer
Quick Start
UPS
2348
+
Quick
Printer
®
Power Cord
Parallel Cable USB Cable
Note: Ethernet option printers do not include any interface cables.
Getting To Know Your Printer
Peeler Bezel
Label Taken Sensor
(Built into door)
Cleaning Pen
Media Access
Door
(Lift to Open)
Printhead
Assembly
& Bracket
Label Mode
Switch
I/O Connectors
Page 2
Media Sensor and Guide printhead
Release Lever
Power Switch
& Cord Module
Auxiliary Media Access
980385-003 Rev.A
Getting To Know Your Printer
Save-A-Printhead
Cleaning Film
(Storage Pocket)
Media Roll
Holder
Controls
Platen
Roller
Platen
(Media Drive)
Roller Bracket
Liner "Peeler"
Gate
Peel/Tear
Bar printhead
980385-003 Rev.A
Page 3
Controls and Indicators
Power
Indicator
Error
Indicator
PEEL
BATCH
OFF
Power Switch
0 = Off
ON 1 = On
O
Button
PAUSE
FEED
CANCEL
Function
Press Once - Halt batch printing.
Press Second Time - Resume batch printing operation.
Press Once - Feed one label or “form”.
Press & Hold - Will feed labels until the
FEED button is released.
Press Once - resets and terminates any print operation in progress and clears the command input buffer.
Indicator LEDs
POWER ERROR
On Solid
Flashing
OFF
Condition Report
OFF
OFF
Power On
Pause
Flashing Printhead Open
OFF
OFF
On Solid Labels Out
On Solid Hardware Error
Mode
Peel
Batch
Label Mode Switch
Description
Print one label and pause. Remove label.
Prints next label. Repeats until print operation is completed. Use label liner rewinder to peel the liner from the label.
Standard operation - Prints one or more labels until the print form operation is complete.
Page 4 980385-003 Rev.A
Installation
Connect the printer power and interface cable.
Check
Voltage
LP 2348
Part No. :
Plus
120XXX-XXX
. : XXXXXXXX
Input
Power: 115V
AC 6.3A
50/60Hz
PEEL
BATCH
Batch
Mode
Serial
Interface
USB
Interface
Parallel
Interface
0 = Off
The printer’s serial port interface (RS-232) default setting is 9600 baud,
No parity, 8 Data bits and 1 stop bit.
Warning - Shock Hazard
See the back page, page 27, for important information on handling, set-up and installation of your printer.
If you use a USB cable, the New Hardware and Printer Wizards help you. Attach the USB cable between the printer and the computer. Turn on the printer. The computer detects a USB device, installs USB printer support; then installs the printer driver.
If the computer prompts you to browse to file locations, find the
OEMSETUP.INF
and
USBPRINT.INF
files under the UPS folder: c:\UPS\Common\Foss\Drivers
980385-003 Rev.A
Page 5
Before Loading Media
You must remove the outside length of media (that is, one, full revolution of labels and any liner). Tape or adhesive holds the loose end and the outside length of media becomes contaminated when handled or stored.When
you remove this part of the media, you remove the oils, dust, and adhesives that contaminate it.
Labels
Remove all labels that are held by adhesives or tape
Tag Stock
Detach both ends of the bottom tag
Page 6
You must avoid dragging adhesive or dirty media between the printhead and platen. Such an occurrence damages the printhead and is not covered under your warranty. Using clean media prevents damage and reduces wear on the printhead and platen.
980385-003 Rev.A
Loading Media
Use approved media for best results.
Step 1
Open printhead.
Step 2
Open media guide.
980385-003 Rev.A
A
B
Page 7
Step 3
Mount and thread the media.
Push the roll tight against the inside roll bracket with the green flip arm.
Page 8 980385-003 Rev.A
Step 4
Thread the media through the media guide and printhead.
980385-003 Rev.A
Page 9
Step 5
Close media guide. Slide the guide against the media until the media touches the inside stop.
A
Step 6
Close the printhead.
B
2"
(50mm)
Page 10 980385-003 Rev.A
AutoSense: Media Calibration
Run the printer's AutoSense routine to calibrate the printer for new media.The printer will measure the label, liner and gap parameters and print a configuration status label.
Step 1
Close the printer.
Step 2
With the label mode switch set to "Batch", turn on the printer.
02/01/0
Power: 115V
AC 6.3A
50/60Hz
Serial
No.:
12345678912
Input
Power:
For home
115-230 or office us e
VAC, 2-1
Amps, 50/60
Hz
N2557
PEEL
BATCH
I.T.E.
8T34
C
®
US
MADE
IN USA
and domestic parts
PEEL
BATCH
980385-003 Rev.A
Page 11
AutoSense: Media Calibration
Step 3
Press and hold the Cancel and Feed buttons for one (1) second and then release only the Cancel button. After three (3)more seconds, release the
Feed button.
1 sec.
3 sec.
3 sec.
1 sec.
Step 4
A "Dump" mode configuration status label will print. Press the FEED button (do not hold down feed button) until “Out of DUMP” prints.
4 MO3257 3.18.01
Serial port : 96,N,8,1
Image buffer size:245K
Fmem:000,0K,019.9K avl
Gmem:000K,0241K avl
E mem:000K,0241K avl
I8,0,001 rY
S8 D12 R032,000 ZT UN q0784 Q1227,034
Option:D
11 12 13 now in DUMP
Page 12 980385-003 Rev.A
Label Peel Mode
The printer can present a single peeled label and wind the backing.
Removing the presented label will prompt the printer to print the next label.
Preparation
Feed approximately 16 inches of media and remove the exposed labels from the liner.
980385-003 Rev.A
Page 13
Step 1
Open the peeler gate. Push the peeler bezel in the lower middle area and the gate will snap open.
Page 14 980385-003 Rev.A
Step 2
Thread the media through the peeler gate and attach the media to the rewind tube with the clip.
980385-003 Rev.A
Page 15
Step 3
Wind the rewind tube counter-clockwise (to remove liner slack) and close the peeler gate.
Step 4
Set the Label Mode switch on the rear panel to PEEL.
PEEL
BATCH
Page 16 980385-003 Rev.A
Step 5
Press CANCEL to initialize the Peel Mode. Carefully close the printer door.
CANCEL
Step 6 - Optional
Press the FEED button to remove slack and the first label is presented.
FEED
980385-003 Rev.A
Page 17
Using UPS Internet Shipping to Install the Printer
1
1. Click on the Shipping tab after Log In.
2
Click on 'Create a Shipment'.
Accept “Terms and
Conditions” to continue.
3
Click on 'Set Preferences'.
4
Scroll to Printing Preferences and click 'Install UPS
Thermal Printer'.
5
Follow the instructions to install the printer driver and plug-in.
6
Now you are able to print via UPS Internet Shipping using your UPS 2348 Thermal Label Printer.
If you have any questions, call the UPS Internet Shipping
Support Help Desk at 877-289-6418.
Page 18 980385-003 Rev.A
980385-003 Rev.A
Page 19
Cleaning Your Printer
The printer’s media path allows for cleaning and clearing of media jams.
The user can clean the printhead, platen roller and areas adjacent to the media path surfaces.
Warning -Shock Hazard
Always turn the printer off before cleaning.
The media path surfaces (except the printhead) can be cleaned with a lint free, clean, damp cloth very lightly moistened with medical grade alcohol. Alcohol may be used to help remove any adhesive or label material buildup.
Warning - Static Discharge.
Never touch the printhead. Always clean the printhead with a cleaning pen (to protect the printhead from static discharge and fibers).
If a label has become jammed in the printer, remove the label and any adhesive residue, immediately. Adhesive may spread through out the printer’s media path if not completely removed. Many adhesives are permanent and have short “set” times.
Page 20 980385-003 Rev.A
Cleaning the Print Head
As you use your printer, the printhead may become contaminated resulting in poor print quality. Whenever new labels are loaded into the printer, the printhead should be cleaned with a cleaning pen.
Step 1
Open the printer and the printhead carriage.
Printhead
Thermal Printer
Cleaning Pen
Step 2
Gently rub the cleaning pen across the amber area of the printhead.
Allow the printhead to dry for 1 minute before loading labels.
Do Not Clean the printhead with sharp objects! Only used approved cleaning materials.
980385-003 Rev.A
Page 21
Print Head Care
The main factors that contribute to reduced head life are:
Touching the printhead! Static electricity can discharge and damage the printhead. The body's oils and acids also damage the printhead.
Cleaning - For optimum performance, clean the printhead regularly after every roll of direct thermal labels.
Abrasion - Over time, the movement of media/ribbon across the printhead will wear through the protective ceramic coating, exposing and eventually damaging the print elements (dots).
Use of proper media - Use only approved media.
Non-approved media may contain chemicals that can destroy or dramatically reduce the printhead's life.
Temperature - printhead density (heat) setting. Set the density to the lowest possible setting that prints a good image.
Print Speed - Fast print speeds have higher friction levels on the printhead's surface.
Regular printhead Conditioning - Use the Save-A-Printhead cleaning film to remove printhead contamination buildup quickly and easily. (Part No.105950-047)
Page 22 980385-003 Rev.A
Printhead Conditioning
Every third new roll of labels the printhead needs regular printhead conditioning. Use the Save-A-Printhead cleaning film to keep particle and contamination build-up from occurring.
Using the Save-A-Printhead cleaning film:
1.
Turn the printer power off. Remove the media.
2.
Clean the printhead with the cleaning pen.
3.
Insert the cleaning film with the label near the printhead.
Save-A-Printhead
Cleaning Film
Follow Instructions
On The Label
4.
Close and latch the printhead. Grasp the cleaning film and pull it out of the front of the printer.
5 Clean the printhead with the cleaning pen.
6.
Record the date cleaned on the rear of the film's label.
7.
Load media and resume printing.
980385-003 Rev.A
Page 23
Cleaning the Platen Roller
The platen (drive) roller normally does not require cleaning. Paper and liner dust can accumulate without effecting print operations. Contaminates on the platen roller can damage the printhead or cause the media to slip when printing. Adhesive, dirt, general dust, oils and other contaminates should be cleaned immediately off the platen.
The platen can be cleaned with a fiber free swab (such as a Texpad swab) or a lint free, clean, damp cloth (such as Kimwipes) very lightly moistened with medical grade alcohol (95% pure or better). Do Not Use
the Cleaning Pen!
1.
Open the printhead and remove the media.
2.
Clean the platen surface with the alcohol moistened swab.
Hand rotate the platen while swabbing.
3.
Repeat this process two to three times with a new swab to remove residual contaminates. Adhesives and oils, for example, may be thinned by the initial cleaning but not completely removed.
Page 24 980385-003 Rev.A
Printer Configuration Settings
The printer has flash (non-volatile) memory to store printer configuration settings. The settings are stored in flash memory and are set by programing, printer drivers or the AutoSense routine. The settings are shown on the Dump mode printout or can be reported back to the host via the serial port or USB interfaces.
The data printed out above the stripe bar is used to identify the printer.
The first line has Print Width (4”), Model Code (MO3257) and Firmware Version (V4.XX.XX XXX). The next lines are Serial Number
(S/N: XXXXXXXX) and serial port setting.
The following are the basic settings stored in the printer:
Speed ( S)
Density ( D) or heat applied
Form (label) length and gap in dots ( Q)
Form (label) width in dots (
q)
Serial port - Set by command line programming with Ycommand
Margin (
R)
Buffer Mode ( r)
Options: D
Print Mode is Direct Thermal (
OD)
Sample
Dump Mode
Printout
980385-003 Rev.A
Page 25
Page 26 980385-003 Rev.A
Warning - Shock Hazard
Never operate the printer in a location where it can get wet.
Personal injury could result.
Caution - Printer Setup & Handling
1)When installing or modifying the printer setup or configuration, ALWAYS TURN POWER OFF Before:
A) Connecting any cables.
B) Performing any cleaning or maintenance operations.
C) Moving the printer.
2) Damage to the printer interface connector, accessories or door may result from placing the printer on it’s front bezel or backside during unpacking or handling.
Warning - Static Discharge
The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the printhead or electronic components used in this device. DO NOT TOUCH the printhead or the electronic components under the printhead carriage.
LP2348+ Thermal Printers
European Council Directive Compliance to Standards
89/336/EEC EMC Directive EN55022-B,1998 RF Emissions Control
EMC Directive EN50024,1998
Immunity to
Electromagnetic
Disturbances
EMC Directive EN61000-3-2: 1995 Harmonic Emissions
EMC Directive EN61000-3-3: 1995
CB Scheme
EN60950
IEC60950
Voltage Variation
Product Safety
FCC - Declaration Of Conformity:
Models: LP 2348+ conform to the following specification:
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a) Class B digital device.
Supplemental Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following Two
Conditions: (1) This device may not cause harmful interference , and (2) this device must accept any interference received, including interference that may cause undesired operation.
Industry Canada Notice:
This device complies with Industry Canada ICS-003 class A requirements.
Cet équipement est conforme à l’ICS-003 classe A de la norme Industrielle Canadienne.
©2004 Zebra Technologies Corporation, all rights reserved.
UPS
®
, UPS OnLine
® and UPS OnLine
®
WorldShip
® are registered trademarks of United Parcel
Service of America, Inc. Windows® is a registered trademark of Microsoft Corporation.
LP2348 and LP2348+ are trademarks of Zebra Technologies Corporation
980385-003 Rev.A
Page 27
&
980385-003
Page 28 980385-003 Rev.A
