Zebra PDT Quick Reference Guide
Zebra PDT is an advanced handheld laser barcode scanning terminal that offers versatile data collection capabilities for various applications. With its lightweight and ergonomic design, it ensures comfortable usage during mobile operations. The device features multiple memory configurations, enabling storage of large data volumes. Zebra PDT's communication versatility is evident through its infrared, serial cable, and optical interface options, allowing seamless data transfer to PCs, host computers, and other devices.
Advertisement
Advertisement
P D T 1 1 0 0
P D T 1 1 0 0
© 1998 - 2001 SYMBOL TECHNOLOGIES, INC. All rights reserved.
Symbol reserves the right to make changes to any product to improve reliability, function, or design.
Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Symbol products.
Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc.
Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, N.Y. 11742-1300 http://www.symbol.com
Patents
This product is covered by one or more of the following U.S. and foreign Patents:
U.S. Patent No. 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805;
4,736,095; 4,758,717; 4,760,248; 4,806,742; 4,816,660; 4,845,350; 4,896,026; 4,897,532;
4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617;
5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148;
5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162;
5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162;
5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924;
5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081;
5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891;
5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322;
5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810;
5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,627,359; 5,637,852;
5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851;
5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500;
5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520;
5,823,812; 5,828,050; 5,848,064; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617;
5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420;
5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,031,830; 6,036,098;
6,047,892; 6,050,491; 6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,068,190; 6,082,621;
6,084,528; 6,088,482; 6,092,725; 6,101,483; 6,102,293; 6,104,620; 6,114,712; 6,115,678;
6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379; 6,172,478; 6,176,428; 6,178,426;
6,186,400; 6,188,681; 6,209,788; 6,216,951; 6,220,514; 6,243,447; 6,244,513; 6,247,647;
6,308,061; 6,250,551; 6,295,031; D305,885; D341,584; D344,501; D359,483; D362,453;
D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581; D414,171;
D414,172; D418,500; D419,548; D423,468; D424,035; D430,158; D430,159; D431,562;
D436,104.
Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875;
1,955,269 (Japan); European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832;
France 81/03938; Italy 1,138,713.
rev. 11/01
Q u i c k R e f e r e n c e
Introduction
The PDT 1100 is a lightweight, battery-powered, hand-held laser bar code scanning terminal. The terminal is available in memory configurations of 2 MB and 512 K. The terminal has communications capabilities through several venues:
• infrared communications directly to a PC with an Ir port
• through the optional cradle
• by serial cable connected to a host computer.
1
P D T 1 1 0 0
About This Guide
This Quick Reference Guide describes the basic operation of the
PDT 1100, including information on:
•
Parts of the PDT 1100 on page 3
•
•
•
Hand Strap and Pocket Clip (optional) on page 8
•
Setting the Backlight on page 8
•
•
Setting the Date and Time on page 10
•
•
-
Using the Cradle (CRD 1100) on page 11
-
Using the Optical Interface on page 12
-
Using the Serial Cable on page 12
•
-
-
Loading the Batteries on page 13
-
Charging the Super Cap on page 14
-
-
Low Battery Indication on page 14
-
Storing the Terminal on page 15
-
Using the Cradle to Charge the NiMH Battery Pack on page 15
•
Using the 4-Slot NiMH Battery Charger on page 15
•
•
.
2
Q u i c k R e f e r e n c e
Parts of the PDT 1100
Confirmation
LED
M4
M2
Hand
Strap
M3
LCD
M1
Connector cover
Battery
Cover
Battery Cover
Lock
Clip (optional)
35864019.eps
Scanner
Window
IR Port
3
Key Pad
P D T 1 1 0 0
M1 & M3 keys
Cursor keys
PW (Power) key
BS (Backspace) key
M2 & M4 keys
Numeric keys
Enter key
Function keys
35864011.eps
C (clear) key
SF (Shift) key
4
Q u i c k R e f e r e n c e
Functions of the PDT 1100 Keys
The functions of the keys may be set by application programs.
Here is a set of sample functions.
Key
M1, M2, M3 or M4
F5-F8 Cursor Keys
PW (Power) Key
BS (Backspace) Key
Numeric Keys
SF (Shift) Key
C (Clear) Key
Function
Press any of these keys to activate the scanner (the scan trigger is assigned to these keys by default).
Depending upon the definition in Systems Mode or in application programs, they may be used as the
Enter key, Shift key, and backlight on/off key. They can also be assigned string data in application programs.
Use to move up or down lines, or to move character by character.
Powers the unit on and off.
Moves the cursor back one character.
Used for numeric input.
Used in combination with numeric keys for special functions.
Clears the last entered data and returns to the original screen.
Powering On/Off
The PW (Power) button is located in the lower left corner of the keypad, and powers the terminal on and off. If the terminal is being powered on for the first time, or is being powered on after a complete discharge, refer to Initializing the PDT 1100 in the PDT
1100 Product Reference Guide (p/n 70-35864-xx).
Loading an Application
To determine the system requirements and to load an application, refer to System Configuration in the PDT 1100 Product Reference
Guide (p/n 70-35864-xx).
5
P D T 1 1 0 0
Scanning Bar Codes
To scan bar codes:
1. Power the terminal on.
2. Aim the scanner window at the bar code.
3. Press the M1, M2, M3 or M4 key.
The laser is emitted from the scanner window. The LED illuminates green to indicate a successful decode. Depending on the system configuration, the unit may also beep upon a successful reading.
• If the PDT 1100 fails to read, change the angle by tilting the unit up or down slightly, or change the distance of the terminal from the bar code.
• Keep the terminal at a distance from a target bar code so that the bar code comes within approximately 90% of the laser scanning range. The PDT 1100 can read bar codes at a maximum distance of 56 cm (22 in.) from the bar code reading window.
• The bar code reading procedure may differ depending upon the application used. Refer to the PDT 1100 Product Refer-
ence Guide (p/n 70-35864-xx).
6
Q u i c k R e f e r e n c e
Scanner confirmation LED
(green when bar code is successfully read).
The trigger switch function is assigned to all the M keys at the factory.
Max. 56 cm. (22 inches)
35864001.eps
7
P D T 1 1 0 0
Hand Strap and Pocket Clip (optional)
Loop the hand strap through the terminal, then put your hand through the strap and hold the PDT 1100. This prevents you from accidentally dropping the terminal.
Hand Strap
Attaching the Clip
First fit the left tab of the clip into the matching groove of the PDT
1100 body and then snap the other tab into place. To remove the clip, insert a flat-edged screwdriver at the edge and twist to disengage.
35864004.eps
Setting the Backlight
The backlight function is off when the terminal is powered on.
Press the M1 key while holding down the SF (shift) key to activate or deactivate the backlight function.
Note: In application programs, you can redefine the key to be used for activating or deactivating the backlight func-
8
Q u i c k R e f e r e n c e tion. You can also modify the time before automatic shut-off.
Adjusting Settings
The LCD brightness can be adjusted between eight contrast levels. The terminal can be set in both beeper and vibration alert modes, and the volume can be adjusted between four levels.
Adjusting the LCD Contrast
1. Press M1 , hold it down and press PW to display the LCD
Contrast screen.
2. Use F5 or F6 keys to select the LCD contrast line in the display.
3. To decrease the contrast, press F7 .
4. To increase the contrast, press F8 .
5. Press the Enter key, or wait 5 seconds to accept the new setting.
Using Beeper and Vibration Modes
The PDT 1100 has three ways to inform you that a bar code has been scanned successfully:
• confirmation LED
• beeper mode
• vibration mode
The confirmation LED and beeper are the default methods of announcing successful scans. Beeper and vibration modes can be used simultaneously.
Adjusting the Beeper Volume
The beeper volume can be adjusted to four levels, from OFF to
MAX.
1. Press and hold M1 . Press and release PW to display the
Beeper Volume Screen.
9
P D T 1 1 0 0
2. Use F5 or F6 keys to select the beeper volume line in the display.
3. To lower the volume, press F7 .
4. To raise the volume, press F8 .
5. Press the Enter key, or wait 5 seconds to accept the new setting.
Switching the Beeper/Vibration Mode
You can set the terminal to beep, vibrate, or do both upon a successful scan.
1. Press and hold M1 . Press and release PW to display the
Beeper/Vibration mode screen.
2. Use F5 or F6 keys to select the Switching Beeper Volume line.
3. Press the F7 key twice to select Beeper mode.
4. Press the F8 key twice to select Vibration mode.
5. Press the F8 key once to select both Beeper and Vibration.
6. Press the Enter key, or wait 5 seconds to accept the new setting.
Setting the Date and Time
1. Hold down the SF and 1 keys and press the PW key to display the SYSTEM MENU screen.
2. Select 4:SET SYSTEM and press the ENT key to display the
SET SYSTEM screen.
3. Select 3:DATE/TIME and press the ENT key to display the
SET DATE/TIME screen.
4. Use numeric keys and enter the year (only the two last digits), month, day, hour (in 24-hour format) and then minutes.
Add a 0 (zero) preceding one digit entries.
5. If you make an incorrect entry, press the BS key and enter the correct data.
10
Q u i c k R e f e r e n c e
6. Press the C key to return to the SET SYSTEM screen.
Using the Keypad
Entering Numeric Data
To enter numeric data, e.g., the quantity of goods, use the ten numeric keys and the Enter key.
If you key in a wrong value, press the C key to clear, or the BS
(Backspace) key and enter the correct data.
Selecting Tasks
If the LCD shows the selection (xxx) prefaced by a number (i.e.,
1: xxx, 2:xxx ), use the numeric keys to select the desired item, then press the Enter key to execute.
If a YES/NO screen (e.g., 1:Yes, 2:No ) appears, respond by pressing 1 for yes, 2 for no.
Entering Alphabetic Characters
The PDT 1100 supports the alphabet input function using letters, characters and spaces from the keypad during execution of an application program. Refer to the PDT 1100 Product Reference
Guide (p/n 70-35864-xx) for more information.
Communications
There are three options for transmission of data.
• CRD 1100 cradle
• Optical interface
• Serial cable
Using the Cradle (CRD 1100)
The optional CRD 1100 is an infrared communications unit with optional charging function. You may either keep the PDT 1100 and the CRD 1100 separated by 10-80 cm (4-30 inches) with their IR
11
P D T 1 1 0 0 ports facing each other, or put the PDT 1100 directly in the cradle to communicate through the cable.
35864008.eps
Using the Optical Interface
The PDT 1100 communicates using a beam of infrared light, so there should be nothing obstructing the line of sight between the terminal and any target stations. In the IrDA communications mode, keep the terminal and target within the effective light emission range, about 10-80 centimeters (4-30 inches). The PDT
1100 can also communicate with other equipment with infrared capability. This is done by aligning the infrared ports. The effective
IR range and IR port angle may differ depending upon the target equipment, so refer to all relevant instruction manuals.
Using the Serial Cable
The PDT 1100 can also be connected directly to a host computer, a modem, or a printer with the optional RS-232C direct-connect serial cable.
For more information on cable connection and communications, refer to the PDT 1100 Product Reference Guide (p/n 70-35864xx).
12
Q u i c k R e f e r e n c e
Batteries
Types of Batteries
The PDT 1100 accepts either two standard AAA batteries or a rechargeable NiMH battery pack (optional). The batteries are not loaded into the terminal when it is shipped from the factory.
Note: For best battery performance at low temperatures (at or below 0°C or 32°F) we recommend using the optional rechargeable NiMH battery pack.
Loading the Batteries
AAA Alkaline Batteries
1. Turn the PDT 1100 upside down. Slide the cover lock in the direction of the arrow and remove the battery cover.
2. Check the polarity of the two new batteries and insert them so that the end of the battery pull strap is above the batteries.
This facilitates easy removal of the batteries.
3. Replace the battery cover, being careful not to pinch the battery pull strap between its cover and the bottom cover. Re- turn the battery cover lock to its original locked position.
NiMH Battery Pack
1. Charge the NiMH battery pack in the cradle battery charging
slot prior to installing it in the terminal (refer to Using the Cra-
dle to Charge the NiMH Battery Pack on page 15 ).
2. Turn the PDT 1100 upside down. Slide the cover lock in the direction of the arrow and remove the battery cover.
3. Check the polarity of the battery pack. Load it so that the end of the battery pull strap appears above the battery pack. This facilitates easy removal of the battery pack.
Make certain grooves on the battery pack are aligned with the slot.
4. Replace the battery pack cover, being careful not to pinch the battery pull strap between its cover and the bottom cover.
13
P D T 1 1 0 0
Return the battery cover lock to its original locked position.
Charging the Super Cap
When powering up for the first time, or when the batteries are out of the terminal for five minutes or more, the super cap must be fully charged to provide memory backup. To fully charge the super cap, insert fresh batteries and allow two hours for the batteries to charge the super cap. If this is not done, there may not be sufficient backup power to maintain data. There is no indication on the terminal when the super cap is charging.
Voltage Indication
To check the current voltage:
1. Press the Enter key while holding down the SF key. The current voltage is displayed as a bar in the LCD window.
2. Release the keys to delete the indication.
For more details, refer to the PDT 1100 Product Reference Guide
(p/n 70-35864-xx).
Low Battery Indication
If the voltage drops below specific levels while the PDT 1100 is in operation, the unit displays two warning messages. The first warning message is:
Battery Voltage has Lowered.
The unit then beeps three times and resumes normal operation.
This message means that the batteries will expire soon. If you do not replace the batteries within a short time, the terminal shows one of the following two messages, beeps five times, and shuts down automatically.
For AAA alkaline batteries:
Replace the Batteries!
14
Q u i c k R e f e r e n c e
For the NiMH battery pack:
Charge the battery!
If either message appears, immediately power off the unit if it has not already shut down automatically, and then replace or recharge the batteries. If using AAA batteries, make sure you have new batteries available before removing old batteries. If you replace the batteries within 3 minutes, you will not experience loss of data.
After battery replacement, power on the terminal and check the operation.
Storing the Terminal
If the PDT 1100 is to be stored for a long time, to flush the contents of RAM (system parameters and user data) to ROM, press and hold the PW key for three seconds. The following message appears:
Now Saving Data
Do not remove batteries until process complete.
Upon completion of the backup, the message disappears. After the message disappears, remove the batteries or battery pack.
Using the Cradle to Charge the NiMH Battery Pack
You can recharge the battery pack using the optional CRD 1100 charge function. The NiMH battery pack can also be completely discharged before recharging using the slot in the cradle. Refer to the CRD 1100 Quick Reference Guide (p/n 70-35862-xx).
Using the 4-Slot NiMH Battery Charger
The optional 4-slot battery charger may also be used to charge or discharge the NiMH battery pack. For more information, refer to the PDT 1100 Product Reference Guide (p/n 70-35864-xx) or the
CRG 1100 Quick Reference Guide (p/n 70-35863-xx).
15
P D T 1 1 0 0
Cleaning
Wipe the scanner window periodically with a lens tissue or other material suitable for cleaning optical material, such as eyeglasses.
Caution: Do not pour, spray or spill any liquid on the scanner.
Troubleshooting
If the scanner does not work after you’ve followed the operating instructions as outlined in this guide, check the following:
• the system power.
• scanning is enabled.
• battery is installed correctly.
• cable connections are not loose, if the cable is in use.
• PDT 1100 is programmed to read the type of bar code you are trying to scan.
• symbol is not defaced.
If the scanner is still not operational, refer to the Service
Information on back cover .
16
Q u i c k R e f e r e n c e
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
Radio Frequency Interference Requirements
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Radio Frequency Interference Requirements - Canada
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Marking and European Union Compliance
Products intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and
European Normes (EN), as follows. Amendments to these Directives or
ENs are included:
17
P D T 1 1 0 0
Applicable Directives
• Electromagnetic Compatibility Directive 89/336/EEC
• Low Voltage Directive 73/23/EEC.
Applicable Standards
• EN 55022:1998, Limits and Methods of Measurement of Radio Disturbance
Characteristics of Information Technology Equipment
• EN 55024:1998; Information Technology Equipment - Immunity characteristics -
Limits and methods of measurement
• IEC 1000-4-2:1995; Electromagnetic compatibility (EMC); Part 4:Testing and measurement techniques; Section 4.2:Electrostatic discharge immunity test
• IEC 1000-4-3:1997; Electromagnetic Compatibility (EMC); Part 4:Testing and measurement techniques; Section 3. Radiated, radio frequency, electromagnetic field immunity test
• IEC 1000-4-4:1995; Electromagnetic compatibility (EMC); Part 4: Testing and measurement techniques; Section 4:Testing electrical fast transient,/Burst immunity
• IEC 1000-4-5:1995; Electromagnetic compatibility (EMC), Part 4: Testing and measurement techniques; Section 5: Surge Immunity
• IEC 1000-4-6:1996; Electromagnetic compatibility (EMC), Part 4:Testing and measurement techniques; Section 6: Immunity to conducted disturbances, induced by radio frequency fields
• IEC 1000-4-11:1994; Electromagnetic compatibility (EMC), Part 4: Testing and measurement techniques; Section 11: Voltage Dips, Short Interruptions, and
Voltage Variations
• EN 60950 + A1+A2+A3+A4+A11 - Safety of Information Technology Equipment
Including Electrical Business Equipment
• EN 60825 - Safety of Devices Containing Lasers.
Laser Devices
Symbol products using lasers comply with US 21CFR1040.10, and IEC825-1:1993,
EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels on the product.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.
18
Q u i c k R e f e r e n c e
Scanner Labeling
VORSICHT! LASERLICHT - NICHT
IN DEN STRAHL BLINKEN
ATTENTION - LUMIÈRE LASER EN
CAS D’OUVERTURE - NE PAS
REGARDER DANS LE FAISCEAU
CAUTION - LASER LIGHT
WHEN OPEN. AVOID DIRECT
EYE EXPOSURE.
The above label appears on the inside of the terminal.
35864091.eps
19
P D T 1 1 0 0
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:
ENGLISH
CLASS 1
CLASS 2
CLASS 1 LASER PRODUCT
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
DANISH / DANSK
KLASSE 1 KLASSE 1 LASERPRODUKT
KLASSE 2 LASERLYF
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
DUTCH / NEDERLANDS
KLASSE 1 KLASSE-1 LASERPRODUKT
KLASSE 2 LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
FINNISH / SUOMI
LUOKKA 1 LUOKKA 1 LASERTUOTE
LUOKKA 2 LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
FRENCH / FRAN ÇAIS
CLASSE 1 PRODUIT LASER DE CLASSE 1
CLASSE 2 LUMIERE LASER
NE PAS REGARDER LE RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
GERMAN / DEUTCH
KLASSE 1 LASERPRODUKT DER KLASSE 1
KLASSE 2 LASERSTRAHLEN
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN
LASERPRODUKT DER KLASSE 2
HEBREW
ITALIAN / ITALIANO
CLASSE 1 PRODOTTO AL LASER DI CLASSE 1
CLASSE 2 LUCE LASER
NON FISSARE IL RAGGIOPRODOTTO
AL LASER DI CLASSE 2
NORWEGIAN / NORSK
KLASSE 1 LASERPRODUKT, KLASSE 1
KLASSE 2 LASERLYS IKKE STIRR INN I LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
PORTUGUESE / PORTUGU ÊS
CLASSE 1 PRODUTO LASER DA CLASSE 1
CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
SPANISH / ESPAÑOL
CLASE 1 PRODUCTO LASER DE LA CLASE 1
CLASE 2 LUZ LASER
NO MIRE FIJAMENTE EL HAZ
PRODUCTO LASER DE LA CLASE 2
SWEDISH / SVENSKA
KLASS 1 LASERPRODUKT KLASS 1
KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLEN
LASERPRODUKT KLASS 2
20
Q u i c k R e f e r e n c e
Warranty
Symbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmanship.
This warranty is provided to the original owner only and is not transferable to any third party. It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol,
(ii) which has not been maintained in accordance with any operating or handling instructions supplied by Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse, abuse, power shortage, negligence or accident or (iv) which has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of customer and is not covered under this warranty.
Wear items and accessories having a Symbol serial number will carry a 90-day limited warranty.
Non-serialized items will carry a 30-day limited warranty.
Warranty Coverage and Procedure
During the warranty period, Symbol will repair or replace defective products returned to Symbol’s manufacturing plant in the US. For warranty service in North America, call the Symbol Support
Center at 1-800-653-5350. International customers should contact the local Symbol office or support center. If warranty service is required, Symbol will issue a Return Material Authorization
Number. Products must be shipped in the original or comparable packaging, shipping and insurance charges prepaid. Symbol will ship the repaired or replacement product freight and insurance prepaid in North America. Shipments from the US or other locations will be made F.O.B.
Symbol’s manufacturing plant.
Symbol will use new or refurbished parts at its discretion and will own all parts removed from repaired products. Customer will pay for the replacement product in case it does not return the replaced product to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange.
Customer accepts full responsibility for its software and data including the appropriate backup thereof.
Repair or replacement of a product during warranty will not extend the original warranty term.
Symbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or phone support, that can be implemented to meet customer’s special operational requirements and are available at a substantial discount during warranty period.
General
Except for the warranties stated above, Symbol disclaims all warranties, express or implied, on products furnished hereunder, including without limitation implied warranties of merchantability and fitness for a particular purpose. The stated express warranties are in lieu of all obligations or liabilities on part of Symbol for damages, including without limitation, special, indirect, or consequential damages arising out of or in connection with the use or performance of the product.
Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way exceed the purchase price of said product, except in instances of injury to persons or property.
Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential damages, so the preceding exclusion or limitation may not apply to you.
21
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and run your applications.
If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center:
United States
United Kingdom
Australia
Denmark/Danmark
France
Italy/Italia
1
Netherlands/Nederland
South Africa
Sweden/Sverige
1-800-653-5350
1-631-738-2400
0800 328 2424
Canada
Asia/Pacific
1-800-672-906 Austria/Österreich
7020-1718 Finland/Suomi
01-40-96-52-21
2-484441
315-271700
11-4405668
84452900
Germany/Deutchland
Mexico/México
Norway/Norge
Spain/España
905-629-7226
337-6588
1-505-5794
9 5407 580
6074-49020
5-520-1835
66810600
+913244000
Latin America
Sales Support
1-800-347-0178 Inside US
+1-561-483-1275 Outside US
Europe/Mid-East
Distributor Operations
Contact local distributor or call
+44 208 945 7360
1
Customer support is available 24 hours a day, 7 days a week.
For the latest version of this guide go to: http://www.symbol.com/manuals .
70-35861-02
Revision B — November 2001
Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
