Features and

Functions Guide

SAMSUNG

Bluetooth

®

Headset

WEP210

Important:

Be sure to first follow the

Quick Start Guide on the reverse side of this guide to complete initial setup of your headset.

Headquarters:

1301 East Lookout Drive Suite 150

Richardson, TX 75082

Internet Address: http://www.samsungmobileusa.com/ accessories

Customer Care Center:

1-888-987-4357

Turn the headset on/off

To turn the headset on,

Press and hold the Multi-Function button for

4 seconds until you see 4 blue flashes on the indicator light, then release.

You will hear a tone and see the indicator light flashes while the power is on

(see Meaning of the indicator light of this guide).

To turn the headset off,

Press and hold the Multi-Function button for

4 seconds until you see blue and red flashes on the indicator light, then release.

You will hear series of 2 tones and see the indicator light stops flashing.

Wear the headset

Wear the headset on your ear.

In general, you will get better performance when there are no obstructions

(including parts of your body) between the headset and the phone.

Use the loop

You can replace the original earpiece cover with the supplied loop earpiece cover. Depending on what ear you are going to wear the headset, simply adjust the loop accordingly.

S Left S Right

Troubleshooting

My phone does not find my headset.

Make sure the blue indicator light on your headset turns on when your phone is searching for devices.

My headsest worked before but now it is

not working.

Make sure your phone is on and the Bluetooth feature is turned on in your phone.

If the Bluetooth feature has been turnned off or was turned on only temporarily, you may need to restart the Bluetooth feature.

If you have confirmed the Bluetooth feature is on in your phone, pair your phone and headset again.

Make calls

Make a voice activated call

If the phone’s voice recognition feature is on, you can make a voice activated call.

1 Press and hold the Multi-Function button. You will hear the voice-activation tone.

2 Say the name of the person you wish to call.

Depending on your phone, this feature may not be supported.

Redial the last number

Press the Multi-Function button. When you release the button, the phone dials the last dialled or received number.

Depending on your phone, how to redial the last number may vary.

End a call

Press the Multi-Function button.

Answer a call

When a call comes in, the headset sounds the ring tone and flashes the blue indicator twice. Press the Multi-Function button.

Do not hold the Multi-Function button down too long when making a call with your voice, ending, or answering a call.

This should only be a quick tap.

Adjust the volume

Press [Volume Up] on the side of the headset to increase the volume level and press [Volume Down] to decrease the volume level .

Use enhanced features

Enhanced features are available for phones that support the

Hands-Free Profile and enhanced features.

• Reject a call

When you receive a call, press and hold the Multi-Function button.

Depending on your phone’s setting or type, you may only be able to mute the ringer or this feature may not be supported.

• Answer a second call

When your phone notifies you of another incoming call while you are on a call, press and hold the Multi-Function button to answer the second call.

You can switch between calls by pressing and holding it.

Depending on your phone, this feature is not supported.

• Place a call on hold

While you are on a call, press and hold the Multi-Function button. To retrieve the call, press and hold the Multi-Function button again. Depending on your phone, this feature may not be supported.

Meaning of the indicator light

Light

Flashes in blue every

8 seconds.

Tone

Quick series of 2 tones.

(Active mode starts.)

Flashes in blue every 3 seconds.

Quick series of 2 tones.

(Standby mode starts.)

Status

The headset is in Active mode.

• The headset has an active

call in progress.

• You can talk up to 4 hours.*

The headset is in Standby mode.

• The headset is waiting

for a call.

• The headset can be in

Standby mode up to 70

hours.*

Flashes in red.

5 tones every

20 seconds.

The battery of the headset is low.

• There is less than 10% of

battery power left. Recharge

the battery.

* Depending on the phone type and usage, the actual time

may vary.

Quick Start Guide

Samsung

Bluetooth

®

Headset

WEP210

Get connected in 4 quick steps

Charge your headset

Put your headset in pairing mode

Turn on Bluetooth on your phone and pair with headset

Test and use

Start here

Before using your headset

Thank you for purchasing the Samsung Bluetooth

Mono Headset WEP210. We hope you will be delighted with its operation.

Take a moment before you get started to familiarize yourself with your new headset.

Multi-Function button

Indicator light

Volume Up button

Earpiece

Volume Down button

Adapter jack Microphone

Make sure you have the following items with your headset:

The items supplied with your headset may vary, depending on your country or service provider.

• Bluetooth version: 2.0 (compatible with devices of

Bluetooth version 1.1 or higher)

• Supported Bluetooth Profiles:

- Headset Profile

- Hands-Free Profile

Headquarters:

1301 East Lookout Drive Suite 150

Richardson, TX 75082

Internet Address: http://www.samsungmobileusa.com/ accessories

Customer Care Center:

1-888-987-4357

Put your headset in pairing mode

Before you can use your headset, you must pair it with your phone.

1 Ensure that the headset is off (see Turn

headset on/off on the reverse side of this guide).

2 Press and hold the Multi-Function button until the blue

indicator light stays on after blinking.

Turn on Bluetooth on your phone and pair with headset

1 Set your Bluetooth phone to discover the

headset by following your phone's guide.

Typically, the steps involve going to the Settings,

Connection, or Bluetooth menu on your

phone and then selecting the option to discover

Bluetooth devices.

Your phone will find the Samsung WEP210

headset and ask if you want to pair with it.

Confirm this by pressing the Yes or OK key.

2 Enter a passkey or PIN, 0000 (4 zeros), then

press the Yes or OK key.

Guide No.: GH68-12949A

11/2006. Rev. 1.0

Charge the headset's battery fully before using the headset for the first time.

1 Plug the travel adapter into the jack on the headset.

2 Plug the travel adapter into the electrical

outlet.

• Charge the headset until the red light on the

headset turns to blue.

• The headset will be fully charged in

approximately 2 hours and 30 minutes.

3 Remove the travel adapter from the headset.

• The headset cannot be used while charging.

• Use only a Samsung-approved charger or adapter.

Test and use

Your phone and headset are now paired and ready to make and receive calls. To confirm they are operating properly, make a call:

1 Place the headset over your ear.

See Wear the headset on the reverse

side of this guide.

2 On your phone, make a call to the number

you want.

3 If your phone and headset are successfully

paired, you will hear ringing on the headset.

After you have successfully paired your phone and headset, you do not need to repeat these initial setup steps each time you use the headset.

Using your WEP210

See Features and Functions Guide on the reverse side of this guide for information on using your

WEP210.