STTH15AC06C
K
A1
A2
K
A1
K
A2
TO-220AB
STTH15AC06CT
A1
A2
K
TO-220FPAB
STTH15AC06CFP
Features
• Ultrafast switching
• Low reverse recovery current
• Reduces switching and conduction losses
• Low thermal resistance
• insulated package TO-220FPAB:
– Insulated voltage: 2500 V
DC
Turbo 2 ultrafast high voltage rectifier
Datasheet
−
production data
Description
The STTH15AC06C uses ST Turbo 2 600 V technology and is suited as a boost diode in air conditioning equipment for continuous mode interleaved power factor correction.
The device is also intended for use as a freewheeling diode in power supplies and other power switching applications.
Table 1. Device summary
Symbol Value
I
F(AV)
V
RRM t rr
(max)
V
F
(max)
T j
(max)
2 x 7.5 A
600 V
25 ns
1.5 V
175 °C
October 2013
This is information on a product in full production.
DocID024884 Rev 1 1/11
www.st.com
11
Characteristics
1 Characteristics
STTH15AC06C
Table 2. Absolute ratings (limiting values per diode at 25 °C, unless otherwise specified)
Symbol Parameter Value Unit
V
RRM
I
F(RMS)
I
F(AV)
I
FSM
T stg
T j
Repetitive peak reverse voltage
Forward rms current
Average forward current
Surge non repetitive forward current
Storage temperature range
Maximum operating junction temperature
Per diode
Per device t p
= 10 ms sinusoidal
600
15
7.5
15
80
-65 to +175
175
V
A
A
A
°C
°C
Symbol
R th(j-c)
Table 3. Thermal parameters
Parameter
Junction to case (TO-220AB)
Per diode
Total
Coupling (TO-220AB)
Junction to case (TO-220FPAB)
Per diode
Total
Coupling (TO-220FPAB)
Value
2.8
1.7
0.6
6
4.5
3
Unit
°C/W
Symbol
I
R
(1)
V
F
(2)
Table 4. Static electrical characteristics (per diode)
Parameter Test conditions Min.
Typ.
Reverse leakage current
Forward voltage drop
T j
= 25 °C
T j
= 150 °C
T j
= 25 °C
T j
= 150 °C
T j
= 25 °C
T j
= 150 °C
V
R
= V
RRM
I
F
= 7.5A
I
F
= 15A
10
1.15
1.4
1. Pulse test: t p
= 5 ms,
δ < 2%
2. Pulse test: t p
= 380 µs,
δ < 2%
To evaluate the conduction losses use the following equation:
P = 1.2 x I
F(AV)
+ 0.04 I
F
2
(RMS)
Max.
1
100
1.9
1.50
2.2
1.8
Unit
µA
V
2/11 DocID024884 Rev 1
STTH15AC06C Characteristics
Symbol
t rr
I
RM t fr
V
FP
Parameter
Table 5. Dynamic characteristics (per diode)
Test conditions
Reverse recovery time T j
= 25 °C
Reverse recovery current T j
= 125 °C
I
F
= 0.5 A, I rr
= 0.25 A, I
R
= 1 A
I
F
= 1 A, V
R
= 30 V, dI
F
/dt = -50 A/µs
I
F
= 7.5 A, V
R
= 400 V, dI
F
/dt = -100 A/µs
Forward recovery time
Forward recovery voltage
T j
= 25 °C
I
F
= 7.5 A, V
FR
= 1.5 V, dI
F
/dt = 100 A/µs
Min. Typ. Max. Unit
25
35 50 ns
3.7
5 A
2.5
100 ns
V
Figure 1. Average forward power dissipation versus average forward current (per diode)
16
14
12
10
8
6
4
2
0
P
F(AV)
(W)
d = 0.05 d = 0.1
I
F(AV)
(
A
)
d = 0.2 d = 0.5 d = 1 d =tp/T
T tp
0 1 2 3 4 5 6 7 8 9
Figure 3. Forward voltage drop versus forward current (maximum values, per diode)
Figure 2. Forward voltage drop versus forward current (typical values, per diode)
100.0
I
F
(A)
10.0
1.0
T j
= 150
°
C
T j
= 25
°
C
0.1
V
F
(V)
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
100.0
I
F
(A)
10.0
1.0
Tj = 150°C
Tj = 25 °C
V
F
(V)
0.1
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0
Figure 4. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220AB)
Z th ( j-c)
/R th ( j-c)
1.0
0.9
0.8
TO- 220AB
0.7
0.6
0.5
0.4
0.3
Single pulse
0.2
0.1
0.0
1.E-04 1.E-03 1.E-02 1.E-01 1.E+00
DocID024884 Rev 1 3/11
Characteristics STTH15AC06C
Figure 5. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220FPAB)
Z th ( j-c)
/R th ( j-c)
1.0
0.9
0.8
0.7
0.6
0.5
TO- 220FPAB
Single pulse
0.4
0.3
0.2
0.1
0.0
1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 1.E+02
Figure 7. Reverse recovery time versus dI
F
/dt
(typical values, per diode)
400
350
300
250 t
RR
(ns)
I j
F
V
T
R
= 7.5 A
= 400 V
= 125 °C
200
150
100
50
0 dI
F
/dt(A/µs)
0 50 100 150 200 250 300 350 400 450 500
Figure 6. Peak reverse recovery versus dI
F
/dt
(typical values, per diode)
12
10
8
I
RM
(A)
V
I
F
T j
R
= 7.5 A
= 400 V
= 125 °C
6
4
2 dI
F
/dt(A/µs)
0
0 50 100 150 200 250 300 350 400 450 500
300
200
100
0
0
Figure 8. Reverse recovery charges versus dI
F
/dt (typical values, per diode)
600
500
Q
RR
(nC)
V
I
F
T j
R
= 7.5 A
= 400 V
= 125 °C
400
50 100 150 200 250 300 dI
F
/dt(A/µs)
350 400 450 500
Figure 9. Reverse recovery softness factor versus dI
F
/dt (typical values, per diode)
3.0
S
FACTOR
2.5
V
I
F
T j
R
= 7.5 A
= 400 V
= 125 °C
2.0
1.5
1.0
0.5
0.0
0 50 dI
F
/dt(A/µs)
100 150 200 250 300 350 400 450 500
Figure 10. Relative variations of dynamic parameters versus junction temperature
2.0
1.5
1.0
0.5
0.0
25
S
FACTOR
I
RM
Q
RR
50 75
I
F
= 30 A; V
Reference: T
R j
= 400 V
= 125 °C
100
T j
(°C)
125
4/11 DocID024884 Rev 1
STTH15AC06C Characteristics
Figure 11. Transient peak forward voltage versus dI
F
/dt (typical values, per diode)
12
10
8
I
T
F j
= 7.5 A
= 125 °C
6
4
2 dI
F
/dt(A/µs)
0
50 100 150 200 250 300 350 400 450 500
Figure 12. Forward recovery time versus dI
F
/dt
(typical values, per diode)
160
140
120
100
V
I
F
T j
R
= 7.5 A
= 1.5 V
= 125 °C
80
60
40
20
0 dI
F
/dt(A/µs)
50 100 150 200 250 300 350 400 450 500
Figure 13. Junction capacitance versus reverse voltage applied (typical values, per diode)
100
C(pF)
F = 1 MHz
V
OSC
T j
= 30 mV
= 25 °C
RMS
10
1
1 10 100 1000
DocID024884 Rev 1 5/11
Package information STTH15AC06C
•
Epoxy meets UL94, V0
•
Cooling method: by conduction (C)
•
Recommended torque: 0.4 to 0.6 N·m
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK
® specifications, grade definitions and product status are available at:
www.st.com
.
ECOPACK
®
is an ST trademark.
Figure 14. TO220AB dimension definitions
A
E
∅P
F
Resin gate
0.5 mm max.
protrusion(1)
Q
H1
D D1
L20
L30 b1
L1
J1
L b e
Resin gate
0.5 mm max.
protrusion(1)
e1
(1) Resin gate position accepted in each of the two position shown as well as the symmetrical opposites
c
6/11 DocID024884 Rev 1
STTH15AC06C
Ref.
c
D
D1
A b b1
E e e1
F
H1
J1
L
L1
L20
L30
∅P
Q
Package information
10
2.40
4.95
1.23
6.20
2.40
13
3.50
Min.
4.40
0.61
1.14
0.48
15.25
3.75
2.65
Table 6. TO220AB dimension values
Dimensions
Millimeters
Typ.
Max.
4.60
0.88
1.70
0.70
15.75
Min.
0.17
0.024
0.045
0.019
0.60
1.27 typ
Inches
Typ.
0.05 typ.
10.40
2.70
5.15
1.32
6.60
2.72
14
3.93
0.39
0.094
0.19
0.048
0.24
0.094
0.51
0.137
16.40 typ
28.90 typ
0.64 typ.
1.13 typ.
3.85
2.95
0.147
0.104
0.41
0.106
0.20
0.052
0.26
0.107
0.55
0.154
Max.
0.18
0.035
0.067
0.027
0.62
0.151
0.116
DocID024884 Rev 1 7/11
Package information
Figure 15. TO220FPAB dimension definitions
H
B
A
L6
Dia
L3
L2 L7
L4
G1
G
F
F1
F2
L5
D
E
STTH15AC06C
8/11 DocID024884 Rev 1
STTH15AC06C
Ref.
H
L2
L3
L4
L5
L6
L7
Dia.
E
F
F1
A
B
D
F2
G
G1
28.6
9.8
2.9
15.9
9.00
3.00
Min.
4.4
2.5
2.5
0.45
0.75
1.15
1.15
4.95
2.4
10
Package information
Table 7. T0-220FPAB dimension values
Dimensions
Millimeters
Typ.
Max.
4.6
2.7
2.75
0.70
1
1.70
1.70
5.20
2.7
10.4
Min.
0.173
0.098
0.098
0.018
0.030
0.045
0.045
0.195
0.094
0.393
Inches
Typ.
16 Typ.
0.63 Typ.
30.6
10.6
3.6
16.4
9.30
3.20
1.126
0.386
0.114
0.626
0.354
0.118
1.205
0.417
0.142
0.646
0.366
0.126
Max.
0.181
0.106
0.108
0.027
0.039
0.067
0.067
0.205
0.106
0.409
DocID024884 Rev 1 9/11
Ordering information STTH15AC06C
Order code
Table 8. Ordering information
Marking Package
STTH15AC06CT STTH15AC06CT TO-220AB
STTH15AC06CFP STTH15AC06CFP TO-220FPAB
Weight Base qty Delivery mode
1.9 g
2.0 g
50
50
Tube
Tube
Date
21-Oct-2013
Table 9. Document revision history
Revision Changes
1 First release.
10/11 DocID024884 Rev 1
STTH15AC06C
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
DocID024884 Rev 1 11/11
