Singer 756 Sewing Machine User Manual

Singer 7-58
Singer 7-61
Form 21027
(159)
Printed in U. S. À
a A : Ji :
Phi
1 e -
Hy
Er
SINGER
MACHINES
5 Nos. 7-58 and 7-61
THE SINGER MANUFACTURING COMPANY
INSTRUCTIONS FOR OILING
To ensure easy running and prevent unnecessary wear of
the parts which are in movable contact, the machine requires
oiling and when in continuous use, "TYPE B” or "TYPE D” OIL,
sold by Singer Sewing Machine Company, should be
applied at least twice each day to all oil holes marked
"OIL", as instructed in Form 8357.
"TYPE D" OIL should be used when an oil is desired
which will produce a minimum of stain on fabrics, even
ofter a long period of storage.
Copyright © 1959 by The Singer Manufacturing Company
1
— —. — nr er
*
-
3
ml lt. ae —————] a, allt) e E кокон ее [=
r r
Tie rr = + Rg 3 pr AT mT. tli ee Ee rim | анти" стнлыиь-
INDEX
Page
Accessories ....eccocorvocccorareneoranveaococenona ........... 29
Bobbin Winder for 7-58 Machine ............e..esncccas ... 29
Bobbin Winder for 7-61 Machine ...........escrcreoocarano 30
Foot Lifter Parts ........eeeeenscconeronecanancocaneuerecanes 30
Machine No. 7-58 ...ere.vccreacoroosnocenconoveooecannaceco 7
Machine No. 7-61 ......e.cooccscacaocaroooceconerenacaneccaeo 17
Numerical List of Parts ,..e..e.c.snsooceracenarnes ....... 33
Thread Unwinder ........ en. ......... peooacccacacavesvancaeces 31
INSTRUCTIONS FOR ORDERING
In ordering from this list, use ONLY the part NUMBER
in the FIRST column.
The number stamped on a Sewing Machine Part is
in every case the number of the single part only.
Every combination of parts sent out as such has its
specific number, which, although not stamped on the
parts, must be used when ordering the combination.
Each number always indicates the SAME PART in
whatever list it appears, or for whatever machine.
The letters after some of the numbers indicate the
style of finish only, as follows:
A—Hardened, Polished, Nickel Plated and Buffed
B—Polished, Nickel Plated and Buffed
C—Hardened Only
D—Polished Only
E—Soft, Not Polished
F—Hardened and Polished
G—Bright Rumbled and Nickel Plated
H—Blued
J—Nickel Plated Only
K—Hardened and Nickel Plated
L—Brass Plated
M—Oxidized |
R—Phosphate Coating Formed on Surface of Iron or
Steel
S—Cadmium Plated
T—Copper Plated
U-—Zinc Plated
V—Silver Plated
W—Polished and Nickel Plated
X—Black Oxide for Iron and Steel
Y—Black Nickel Plated Only
Z—Chromium Plated
A.A—Buffed and Chromium Plated
A.B—-Hardened, Polished, Buffed and Chromium Plated
A.E—Hardened, Bright Rumbled and Nickel Plated
A.F—Hardened, Bright Rumbled, Nicke! Plated,
Bright Rumbled and Chromium Plated
A.G—Alumilite (Plain)
A.H—Alumilite (Dyed) Color Must be Stated
A.J—Polished, Nickel Plated and Chromium Plated
A.K—Hardened, Polished, Nickel Plated and Chromium
Plated
A.Ll-Heat Treated for Toughness
A.L.D—Heat Treated for Toughness and Polished
A.L.X—Heat Treated for Toughness and Black Oxide
INSTRUCTIONS FOR ORDERING
A.S—Black Moulded Phenolic
A.T—Beige Moulded Phenolic
A.U—Brown Moulded Phenolic
A.W-—Hardened then Flame Coated with Tungsten
Carbide
B.A—Chrome Nickel Satin Finish
B.B—Hardened and Chrome Nickel, Satin Finished
C.R—Hardened and Phosphate Coating Formed on
Surface of Steel
F.J—Hardened, Polished and Nickel Piated
T.A—Hardened, Polished, Copper and Nickel Plated
and Buffed
T.B—Copper and Nickel Plated and Polished
T.J—Copper and Nickel Plated Only
T.K—Hardened, Copper and Nickel Plated
T.L—_Copper and Brass Plated
T.M—Copper Plated and Oxidized
X.C—Hardened and Black Oxide for Iron and Steel
Z.A—Hardened, Polished Nickel Plated, Buffed and
Chromium Plated
Z.B—Polished, Nickel Plated, Buffed and Chromium
Plated
Z.C—Hardened and Chromium Plated
Z.D--Polished and Chromium Plated
Z.G--Bright Rumbled, Nickel Plated, Bright Rumbled
and Chromium Plated
Z.J—Nickel and Chromium Plated
Z.T—Copper and Chromium Plated
These letters MUST BE USED when they appear in the
list; and AFTER the number as in the list.
In this series:
1 to 1500, 50001 to 51500 and 140001 to
142,000 are screw numbers
1501 to 1800 and 51500 to 51800 are nut numbers
1801 to 2000 and 51801 tc 52000 are roller numbers
2001 to 50000 and 52001 to 140000 and 142001 to
190000 are Sewing Machine Parts, 190001 and up-
ward are numbers of Electrical Parts.
The figures in the second column refer only to the
plates, illustrating the parts, and are NOT TO BE USED
in ordering.
Parts marked with an asterisk (*) are furnished only
when repairs are made at the factory.
When ordering parts which differ as to gauge (the
distance between seams), the gauge as well as the num-
ber must be given on the order.
LIST OF PARTS COMPLETE
FOR
MACHINE NO. 7-58
FOR GENERAL WORK IN CANVAS, TWO NEEDLES.
TWO SHUTTLES.
AND 1 INCH,
THE iNCH. NEEDLE BAR STROKE 2-1/4 INCHES,
GAUGES 3/4 INCH, 7/8 INCH
LENGTH OF STITCH 2 TO 8 TO
CLEARANCE UNDER PRESSER FOOT 9/16 INCH.
No. Plate
* 19964 — ---.---
8702 22809
58564 22809
50348E 22809
58678 22809
11354 22809
437AL 22809
| 949D 22809
. 9842 22809
| 19668 22811
| 650 22811
| *19556 -------
eS 58218 22812
51464 22812
INDEPENDENT UPPER AND UNDER FEED,
o SPEED UP TO 500, DEPENDING ON MATERIAL
USED AND OPERATIONS PERFORMED.
Name
Arm Dowel Pin (2)
Arm Oil Tube for oiling Arm Shaft
Intermediate Bearing
ANA чб
Arm Screw (4)
+
Arm Shaft ...........
Arm Shaft Bushing «coerce,
Arm Shaft Bushing Set Screw ec
Arm Shaft Screw
н.а
Arm Shaft Screw Washer..............esoorcevoriaoneo.
Arm Side Cover
Bed ......
Cloth Plate ............
Arm Side Cover Hinge Screw............—..
кйифжий ннгй же вн ев
Cloth Plate Screw (4)
No.
11363
145E
565C
1513)
58327
- 307C
15133
56814
11367
445C
11368
565C
1513)
58328
381D
11370
58231
565C
1513)
19970
19971
19812
346E
1861
564C
58384
1508E
19967
2022
134E
PARTS FOR MACHINE No. 7-58
Plate
22809
22809
22809
22809
22814
22814
22814
22809
22809
22809
22809
22809
22816
NOTE:
22816
22809
22809
22809
22814
22814
22814
22814
22814
22814
22814
22814
22814
Name
Crank Connecting Rod with two 145E........
Crank Connecting Rod Cap Screw (2) .......
Crank Connecting Rod Hinge Screw ..........
Cronk Connecting Rod Hinge Screw Nut...
Feed (lower) Bar — 2....... ..eeemeeeecdarerrerecercenene...
Feed (lower) Bar Screw Center (2) ............
Feed (lower) Bar Screw Center Nut (2) ....
Feed {lower) Bar Screw Center 307C with
1513J (2) -........reeneaananenea eno coa on Dean eLcenen enema
Feed (lower) Cam with two 445C ................
Feed (lower) Cam Set Screw (2) .........e._...
Feed (lower) Connecting Link
Feed (lower) Connecting Link Hinge Screw
(2) ..eeennecnioroeonenea eno cane nne enter eun saree sees
Feed (lower) Connecting Link Hinge Screw
Nut (2) ...... e... enn ionioo riecarconerenacinere emnaccane ree
Feed (lower) Dog, 13 teeth (10 teeth to
the inch) ..........e-eeeeeemeeeeerericenienr ee enna nana
When ordering No. 58328, state gauge
required.
Feed (lower) Dog Screw (2)...........e.- meme...
Feed (lower) Forked Connection .........
Feed (lower) Forked Connection 11370
with 11368, 11375, 50322D and two each
565C and 1513) _…...…....…omrrsseessancanenra ser an ane
Feed (lower) Forked Connection Hinge
Screw. coven.
Feed {lower} Forked Connection Hinge
Screw Nut .............eeeeinmieacanerorreenern convencen.
Feed (lower) Lifting Rock Shaft with 134E,
2022 and 19967 ............
Feed (lower) Lifting Rock Shaft complete,
Nos. 19812 and 19970 ...............emmenrrezaceeners
Feed (lower) Lifting Rock Shaft Crank
with 345E and 18961 -..........ree..een2enmacorereróavere
Feed (lower) Lifting Rock Shaft Crank
Clamping Screw iar
Feed (lower) Lifting Rock Shaft Crank
Roller and Stud ..
Feed (lower) Lifting Rock Shaft Screw
Center (2) ..........-.....cm00nme0rvezen nen en raven ene cone
Feed (lower) Lifting Rock Shaft Screw
Center 564C with 1508E (2) -+-e-ese2neminivenasnnce
Feed (lower) Lifting Rock Shaft Screw
Center Nut (2) ......
Feed (lower) Lifting Rock Shaft Wearing
Block ...............en0nevestencana ron enana raro rccoe rover e.
Feed (lower) Lifting Rock Shaft Wearing
Biock Position Pin ......
Feed (lower) Lifting Rock Shaft Wearing
Block Screw ........——......
No.
11375
568E
50322D
58233
58234
58235
346E
564C
58384
1508E
19669
19670
19671
19672
190E
2117
AS6AL
19673
159D
1340
19674
145E
19675
381D
795€
445C
448AL
1520E
23D
PARTS FOR MACHINE No. 7-53 9
Plate Nome
22809 Feed (lower) Regulator eee
22809 Feed (lower) Regulator Hinge Screw .........
22809 Feed (lower) Regulator Thumb Screw ........
22814 feed (lower) Rock Shoaft.......... eee...
== ----- Feed (lower) Rock Shaft complete, Nos.
58233 and 58235 cirri rere vvarnnns
22814 Feed (lower) Rock Shaft Crank with 346E
22814 Feed (lower) Rock Shaft Crank Clamping
Serew .............erncennanenenni roce rica iaa as tastes ea pans
22814 Feed (lower) Rock Shaft Screw Center (2)
ana Feed (lower) Rock Shaft Screw Center
564C with 1508E (2)...........e-.vere-mme-ncoverororecana
22814 fFeed (lower) Rack Shoft Screw Center Nut
(2) e... re. erecaenecacennraio nene nee nacen erre enene ene
22820 Feed (upper) Bar .......... ..
-22822 Feed (upper) Bor Guide Bracket (lower)
- with A56AL ..........e.ee2cermecceeiorenecom reo e.
——— Feed (upper) Bar Guide Bracket (lower)
complete, for 3/4 in. to 1-1/8 in. gauge,
Nos. 19670, 19672 and two 190E ..............
22822 Feed (upper) Bar Guide Bracket {lower)
00 SO anar
22822 Feed (upper) Bar Guide Bracket (lower)
Cap Screw (2) ............emervecerececnrnecca mece erre.
22822 Feed (upper) Bar Guide Bracket (lower)
Pin neeeaeeeneoraonenenenecenernerarraarovarenaroracamarore novena
22822 Feed (upper) Bar Guide Bracket (lower)
Set Screw ore rss rn
22820 Feed (upper) Bar Guide Bracket (upper)
for 3/4 in. to 1-1/8 in. gauge ennnaneneaco ra
22820 Feed (upper) Bar Guide Bracket (upper)
Screw (back) cirri
22820 Feed (upper) Bar Guide Bracket (upper)
Screw {front} ............
22820 Feed (upper) Bar Hinge Bracket
with 145E, 795C and two 445C ние.
22820 Feed (upper) Bar Hinge Bracket Adjusting
SCTOW | Lecnecrssnaseniansentanrenrrsn ea raeuaera rare vm saree eos
22824 Feed (upper) Bar Hinge Bracket Guide
Plate …....….........errerererarensennanen rensencenm an ee sare one
22824 Feed (upper) Bar Hinge Brocket Guide
Plate Screw (2) — 2... een... ennorivenonrrecararaeamon
22820 Feed {upper) Bor Hinge Bracket Set
Screw (lang).........e...-re.enrenvericoneeeno or aner treo
22820 Feed (upper) Bar Hinge Bracket Set
Screw (short) (2) ovine
22820 Feed (upper) Bar Hinge Bracket Support
Screw .............
22820 Feed (upper) Bar Hinge Bracket Support
Screw Nut csr e
22820 fFeed (upper) Bar Hinge Screw ..................-
10
No.
58511
445C
19527
650
19528
912C
1596D
19529
231C
3012
453AL
19677
11708
3012
1804
453AL
11698
19678
2117
1845
1518E
453AL
19532
2117
453AL
19679
690D
1654C
26419
885D
19535
19536
19680
19681
19539
PARTS FOR MACHINE No. 7-58
Plate
22809
22809
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22825
22816
NOTE:
22816
22816
23969
23969
22822
Name
Feed (upper) Com with two 445C ..............
Feed (upper) Cam Set Screw (2) ............e....
Feed (upper) Connecting Link ...............
Feed (upper) Connecting Link Hinge Screw
Feed (upper) Regulator with 231C and
453AL ...........
Feed (upper) Regulator Adjusting Screw...
Feed (upper) Regulator Adjusting Screw
Мы? ….….………srerees
Feed (upper) Regulator Adjusting Screw
Sleeve ...
Feed (upper) Regulator Adjusting Screw
Stop Screw ...........—.me=micenona
Feed (upper) Regulator Pin ...........e me.
Feed (upper) Regulator Set Screw...............
Feed (upper) Regulator Shaft uvre
Feed (upper) Regulator Shaft Driving Crank
with 453AL опа 1804...
Fesd (upper) Regulator Shaft Driving Crank
Pim ecermencocorrerarenevenenrncana canamo nora cacamo e ooano re Danea
Feed (upper) Regulator Shaft Driving
Crank Roller and Stud … ..
Feed (upper) Regulator Shaft Driving
Crank Set Screw
Feed (upper) Shaft ..
Feed (upper) Shaft Cronk with АБЗАЦ,
15 18Е оп 1845 ................e.r11evecavecerionoenene ree.
Feed (upper) Shaft Crank Pin ..............— em...
Feed (upper) Shaft Crank Rolier and Screw
Stud cr rrr arr rs ern ne
Feed (upper) Shaft Crank Roller and Screw
Stud NUL v.........e.eeenecerencaeeneece re casona revoca reme pases
Feed (upper) Shaft Crank Set Screw ..........
Feed (upper) Shaft Driving Crank with
AS3ÁL enrrnvicconoevearanenacaasenanenenanrecaramerden erecto rea
Feed (upper) Shaft Driving Crank Pin ........
Feed {upper} Shaft Driving Crank Set
Screw .........
Feeding Foot. enenonenme en emanan naraenanenranaconene rue cana one
When ordering No. 19679, state gauge
required.
Feeding Foot Screw. reas
Feeding Foot Screw Nut —.......... em e=e.e.e..en..
Guide (6 in. face) ...........—.—. menos naracocoue nues.
Guide Thumb Screwe .........e.e.e0imeianemeneccaco reee
Lifting Presser Bar .......... pause
Lifting Presser Bar 19535 with 64052 . нее...
Lifting Presser Bar Bell Cranik..................
Lifting Presser Bar Bell Crank complete,
Nos. 611C, 19540 and 19680 . e enicacanar
Lifting Presser Bar Bell Crank “Adjusting
Link ........
No.
19540
1828
372C
1518E
2718
611C
19682
523C
445C
51260AL
51609E
11909
8760
16D
8761
19683
8763
8973
43267
257E
713E
11031
58252
1177D
11661
50323D
58677
350C
19732
19735
PARTS FOR MACHINE No. 7-58 11
Plate
23970
23970
23970
23970
23970
22822
‚ 22822
22822
23970
23970
22820
22820
22820
22820
22820
22820
22820
22820
22822
22822
23971
23971
23971
23971
23971
23973
23973
23974
Name
Lifting Presser Bar Bell Crank Adjusting
Link complete, Nos. 1518E, 1828, 2718
and 19539..
Lifting Presser Bar Bell Crank Adjusting
Link Roller with 372C .....uscesrensecsusinencaeuss
Lifting Presser Bar Bell Crank Adjusting
Link Roller Screw ............ reiveeerccnecir eee
Lifting Presser Bar Bell Cronk Adjusting
Link Roller Screw Nut ..........
Lifting Presser Bar Bell Crank ‘Adjusting
Link Roller Screw Nut Washer....................
Lifting Presser Bor Bell Crank Adjusting
Link Screw incre ena
Lifting Presser Bar Bell Crank Connecting
Stud with 445C and 523C iii
Lifting Presser Bar Bell Crank Connecting
Stud Set Screw (large) ….........--0-02000-000000e
Lifting Presser Bar Bell Crank Connecting
Stud Set Screw {small} ...............——.—..--.—...
Lifting Presser Bar Bell Crenk Hinge
Serew—...re.cees meine cacronan eran cuen enana yan ern sree renames
Lifting Presser Bor Bell Crank Hinge
Screw NUE oir ress renee es eans
Lifting Presser Bar Lifter with 8761 and
Lifting Presser Boar Lifter Friction Washer
Lifting Presser Bor Lifter Hinge Screw
Lifting Presser Bor Lifter Stop Pin ..........
Lifting Presser Bar Lifting Link ..............
Lifting Presser Bar Lifting Link Hinge
Stud ........errerence—coacarozonoooiouere sa oeane rana nane ree
Lifting Presser Bar Lifting Link Hinge
Stud Pin 2..v...eeemoenaoecca ao aereo reee arenero
Lifting Presser Bar Lifting Link Hinge
Stud Washer ..............e=.ese-sre-esonerececerarace nene
Lifting Presser Bar Screw Bushing {lower)
Lifting Presser Bor Screw Bushing({upper)
Lifting Presser Bar Spring (flat) ................
Lifting Presser Bar Spring Bracket ..........
Lifting Presser Bor Spring Brocket
Screw (2) ....
Lifting Presser Bar Spring Guide Pin.......
Lifting Presser Bor Spring Regulating
Thumb Screw .........e..eenerceserenorecoveraromesceemeraane
Machine Pulley (10 in. diam.) 1/2 in. Y”
Belt Groove, with two 350C .......e.e..... ree...
Machine Pulley Set Screw (2) revers
Neadle Bar ...........e.....r-.erereconirarian secre cea
Needle Bar complete, with Adjustable
Clomps for 3/4 in to 1-1/8 in. gauges, Nos.
19732, 19733, 19734 and two B98D ..........
12
No.
566C
1513]
58203
129E
445F
257E
19733
19734
8980
191F
* 58253
11917
9084
2205
207F
8953
11918
8482
207F
58254
134D
58573
58566
58585
58586
1508J
51237C
1508)
11165
58567
58570
58568
127848
19567
11848
19696
40025
PARTS FOR MACHINE No. 7-58
Plote
23974
23974
= ново
о =
Мате
Needle Bor Connecting Link Hinge Screw
Needle Bar Connecting Link Hinge Screw
Nut evmmeemsrssrinnserranssosasemssresnnssisssnanassnsmnerssanysnnnas
Needle Bar Connecting Stud with Link and
129E and 445 .................2v000000rizaazonocinocaanare
Needle Bar Connecting Stud Clamping
Serew ........i.eenrireresooninanceraco nee nacen anne naves enano
Needle Bar Connecting Stud Set Screw ....
Needle Bar Screw Bushing (2) --.....-—.w——.=....
Needle Clamp (left) with 191F --......n..e.—..
Needle Clamp (right) with 191F .......e...—.
Needle Clamp $сгем (2) -...........ereermeemeneo.s
Needle Set Screw (2) -......e.ercaruacrrereenecanenomeea
Cil Cup .......
Oil Cup Cover .......... vearrasane same mean cas een
Oil Cup Cover Hinge Pin cerennervaneanenananmaceneeo
Oil Cup Cover Latch Spring -..............e....
Oil Cup Cover Latch Spring Screw ............
Oil or Wax Stripper {feit) (2) .....ееееенненнннныые.
Qil or Wax Stripper Washer (steel) for use
with 11917 ...e..e....sesnencarrenen en mare mee reaneenene
Oil or Wax Stripper Washer (steel) for use
with 58253 .......e.me=m=cermnnercaconeoncareazaceo errores
Qil or Wax Stripper Washer Screw (2) ........
Oil Cup complete, Nos. 2205, 8482, 9084,
11917, 11918, 58253, two 8953 and three
©! Сар бегем rre
Oscillating Rock Shaft ...........e..... nin...
Oscillating Rock Shaft complete, Nos.
1508J, 11165, 51237C, 58570, 58573 ond
58586 cveeeeeerrrrrrrrrrreertererensieensitesisasinanranssnnanans
Oscillating Roek Shaft Hinge Pin...
Osciliating Rock Shaft Hinge Pin 58585
with 1508J .. ..
Oscillating Rock Shaft Hinge Pin Nut ......
Oscillating Rock Sheft Hinge Pin Screw
Bearing ...... ...
Oscillating Rock Shoft Hinge Pin ‘Screw
Bearing Nut .........=..e..—.7v6ennicenecornecenanca rene ne nenes
Oscillating Rock Shoft Oil Pad „нон неснньоы ыы
Oscillating Rock Shaft Oil Tube .....
Oscillating Rock Shaft Oil Tube complete,
Nos. 58567, 58568 ond 127848 -.......e...e.....
Oscillating Rock Shoft Oil Tube Joint
Oscilloting Rock Shaft Oil Tube Oil Cup...
Oscillating Shaft oe
Oscillating Shot Crank ............——eeseesecrnras
Oscillating Shaft Crank complete, Nos.
AS3AL, 1513J, 5868 and 11848 -..........——..
Oscillating Shaft Crank Pin ...........--.————.—.—.
453AL
9119
5868
190€
5968
1054C
1513.)
11919
58512
58513
58527
58625
12002
122419
120571
58660
58661
774F
58515
58662
11910
58517
58518
58527
58626
12002
122419
120571
58663
58664
774F
58520
58665
19572
PARTS FOR MACHINE No. 7-58 13
Plate Name
23976 Oscillating Shaft Crank Set Screw ..............
23976 Oscillating Shaft Crank Slide Block ..........
=-..--- Oscillating Shaft Crank Slide Block
complete, Nos. 190E, 1054C, 5968 and
DT TD 0erienies o acacacronrneeenvar ananacenaann anno moceon enmenr sans
23976 Oscillating Shaft Crank Slide Block Cap
Screw .........
23976 Oscillating Shaft Crank Slide Block Cap
Screw Washer cesser eee
23976 Oscillating Shoft Crank Slide Block Screw
¡1! ET renee
23976 Oscillating Shaft Crank Slide Block Screw
Stud NUE coer reeves eee
23979 Shuttle (inside) Bobbin ............w_..rmcesmenirrncaza
23979 Shuttle (inside) Cylinder .....................-......
окне. Shuttle (inside) Cylinder 58512 with 774 Е
and 58515 .............m.eececercorenanencariragene tner recen.
23979 Shuttle (inside) Cylinder Hinge Pin ..........
23979 Shuttle (inside) Cylinder Latch ...............-
23979 Shuttle (inside) Cylinder Latch Pin ..........
23979 Shuttle (inside) Cylinder Latch Spring
23986 Shuttle (inside) Cylinder Opener ...............,
23979 Shuttle (inside) Frame ..........
EP Shuttle (inside) Frame 58660 with 12002,
58625 and 122419 iriver ren
23979 Shuttle (inside) Tension Regulating Screw
23979 Shuttle (inside) Tension Spring — ................
23979 Shuttle (inside, cylinder) 3 in. diam.
complete, Nos. 11910, 58513, 58527,
58661 and 120571 -................—.... ere semen.
23979 Shuttle (outside) Bobbin sr
23979 Shuttle (outside) Cylinder ....................n.eoecc
====--- Shuttle (outside) Cylinder 58517 with 774F
ond 58520 .............e....e.ee.. cersane ss
23979 Shuttle (out side) Cylinder Hinge Pin eras
23979 Shuttle (outside) Cylinder Latch ..............
23979 Shuttle (outside) Cylinder Latch Pin ........
23979 Shuttle {outside} Cylinder Latch Spring ....
23986 Shuttle (outside) Cylinder Opener ............
23979 Shuttle (outside) Frame ...........
=..... Shuttle (outside) Frame 53663 with 12002,
58626 and 122419 -................ 220000000000
23979 Shuttle (outside) Tension Regulating Screw
23979 Shuttle (outside) Tension Spring .............
23979 Shuttle (outside, cylinder) 3 in. diam.
complete, Nos. 11910, 58518, 58527, 58664
and 120571 coterie reverses ress sarees re enna
23976 Shuttle Driver with 445C.. recconoo enema names
NOTE: When ordering No. 19572, state gauge
required.
14
No.
8873
445C
19575
19576
11833
19577
32D
19578
19579
58277
123D
11241
8879
19684
1535E
8787
710E
58599
19685
19686
19687
164D
41544
58795
19889
19689
1660
2102
1560C
8905
408E
58600
686E
58590
2103
11425
11950
PARTS FOR MACHINE No. 7-58
Plate
23976
23976
23982
23982
23982
23982
23982
23982
NCTE:
23982
NOTE:
23982
23982
22824
22824
NOTE:
22824
22824
22824
22824
14m
Name
Shuttle Driver Pin 2e...ne.erenmvenonnenenan enano
Shuttle Driver Set Screw — .......e.meeemvecenaan nena
Shuttle Race Back {inside}...
Shuttle Race Back (outside) ........... me...
Shuttle Race Back Position Pin (4) --.-......
Shuttle Race Back Spring (2) --........—.———————.
Shuttle Race Back Spring Screw (2)............
Shuttle Race Body .................-.emeeemeneneoneens
When ordering No. 19578, state gouge
required
Shuttle Race complete, Nos. 19575, 19576,
19578, two each 32D, 19577 and four 11833
When ordering No. 19579, state gauge
required.
Shuttle Race Dowel Pin (2)-.-........—r..m..em...
Shuttle Race Screw (2) …….……ecrerenancerennenes
Tension Friction Washer (cloth) large ......
Tension Friction Washer (cloth) small (2)
When ordering No. 8879, state color
required.
Tension Friction Washer (steel) ..............
Tension Regulating Thumb Nut eee.
Tension Regulating Thumb Nut Washer …
Tension Screw Stud .............1.emvermanerencerrener
Tension Screw Stud 710E with 1535E ......
Tension Screw Stud Flange ess
Tension Spring ccm ress
Tension Thread Guard in... 2=eserreoenenoneneen
Tension Thread Guard Screw .........—e.—. e...
Tension Thread Guard Screw Washer ........
Tension Wheel (2) ..........——.ererernrrerenenna mann
Tension (wheel) complete, Nos. 8787,
11241, 19684, 19685, 19686, 58599 and
two each 8879 and 58795 mnie
Thread Eyelet (double) top of orm ............
Thread Eyelet Screw ..............eeeenonreneeaena
Thread Retaining Disc (4) -...........+>e.e=.....
Thread Retaining Regulating Thumb Nut (2)
Thread Retaining Regulating Thumb Nut
Washer (2) ..........eee--ee.e.0000nemenanceracanercev anar
Thread Retaining Screw Stud ........—.—........
Thread Retaining Screw Stud 408E with
1560С .......e..c2v0rnecrncacnenco vers even seanenaennas are recente
Thread Retaining Screw Stud .........—........
Thread Retaining Screw Stud 686E with
1560C .......... ..
Thread Retaining Spring (2) .........e.e-...mesos
Thread Retaining Thread Eyelet for use
with 11426 .. ..
Thread Retaining Threod Eyelet for use
with 11041 .........—.e=e.omnanennanman nano enano nene
No.
11426
11041
11428
8873
434C
58301
58302
58316
50437D
1995
1518E
19690
19614
19694
19691
19692
164D
41544
19793
19693
19591
19997
19592
401D
19593
381D
PARTS FOR MACHINE No. 7-58 15
Plate
23985
23985
22809
22809
22809
22809
22824
22824
22824
22816
22816
NOTE:
22816
NOTE:
22816
22816
NOTE:
22816
Name
Thread Retainer {long stud) complete, Nos.
2103, 8905, 58600 and two 2102 -.............
Thread Retainer (short stud) complete, Nos.
2103, 8905, 58590 and two 2102 ..............
Thread Take-up Cam with two 434C
Thread Take-up Cam Pin -....................e.e——..
Thread Take-up Cam Set Screw (2) ...........
Thread Take-up L@YeP or
Thread Take-up Lever 58301 with 1995 ..
Thread Take-up Lever 58302 with 50437D
Threod Take-up Lever Hinge Screw
Thread Take-up Lever Roller ond Screw
Stud with 1518E creme eee
Thread Take-up Lever Roller and Screw
Stud Nut ............-.ezmeieerrerrannasenenenenan ee eera een
Thread Take-up Spring eee
Thread Take-up Spring Hook for 19691
Threod Toke-up Spring Hook for 19675 ....
Thread Take-up Spring Lever with 19614
and 19793 ...........e...eereenerinereorrreaoresarererenonerece
Thread Take-up Spring Lever Regulator ....
Thread Take-up Spring Lever Regulator
Screw
Thread Toke-up Spring Lever Regulator
Screw Washer coerce reece,
Thread Toke-up Spring Lever Step Pin ....
Thread Take-up Spring Lever Washer ........
Throat Plate Body ...............e.esestiminiez een eee.
Throot Plate Needle Hole Strip (left) for
3/4 in. to 1 in. gouges, in steps of 1/16
DIA. eenareneaenenvanaanenentnanamenenemanne atenta enaeonenerenec emana
When ordering No. 19997, state gauge
required,
Throat Plate Needle Hole Strip (right) for
3/4 in., 13/16 in., 7/8 in., 15/16 in. and 1
IN. GAUGES .-.-....00erecscreccanrenrrererreranapansesran aan se
When ordering No. 19592, stote gouge
required.
Throat Plate Needle Hole Strip Screw {4}
Throat Plate complete, Nos. 19591, 19592,
19997 and four 401D, for 3/4 in. individual
gauge, and from 13/16 in. te 1 in, gauges.
When ordering No. 19593, stote gauge
required.
Throat Plate Screw (2)
EHEN
LIST OF PARTS COMPLETE
FOR
MACHINE NO. 7-61
FOR GENERAL WORK IN CANVAS. TWO NEEDLES.
TWO SHUTTLES. GAUGES ! INCH TO 1-1/2 INCH.
LENGTH OF STITCH 2 TO 8 TO THE INCH. NEE-
DLE BAR STROKE 2-1/4 INCHES. CLEARANCE
UNDER PRESSER FOOT 1/2 INCH. INDEPENDENT
UPPER AND UNDER FEED. SPEED UP TO 500,
DEPENDING ON MATERIAL USED AND OPERA-
TIONS PERFORMED,
22810
22810
22810
22810
22810
22810
22810
22810
22811
22811
22813
22813
22813
22810
22810
22810
22810
22815
22815
22815
22810
22810
22810
22810
22810
22817
22818
Nome
Arm Dowel Pin (2) iii eee ans
Arm Screw (4) .............. amena ra core en bnoerenonanamananes
Arm Screw Washer (4) ................ emanaciones
Arm Shaft oer re a
Arm Shaft Bushing cocci,
Arm Shaft Bushing Set Screw ....................
Arm Sheft Screw cover e
Bad eb ete rene
Cloth Plate for use with 58438 -................
Cloth Plate for use with 58425, 58429,
58457 and 58584 ............e2 ..eeeereirion eee eee.
Cloth Plate Screw (4) .................... RO
Crank Connecting Rod with two 575E ......
Crank Connecting Rod Cap Screw {2} ........
Crank Connecting Rod Hinge Screw ..........
Crank Connecting Rod Hinge Screw Nut ....
Feed (lower) Bar ................e. ...emrereeos
Feed (lower) Bor Screw Center (2) ............
Feed (lower) Bar Screw Center Nut (2)......
Feed (lower) Bar Screw Center 307C with
15134 (2) ...... :
Feed (lower) Cam with two 445C ..............
Feed (lower) Cam Set Screw (2) ..........w....
Feed (lower) Connecting Link ............
Feed (lower) Connecting Link Hinge Screw
(Z) _..xcecccocovenerrensmanen saraceencnacerercerecnanas araraan anus
Feed (lower) Connecting Link Hinge Screw
Nut (2) cicero een
Feed (lower) Dog 13 teeth (10 teeth to the
inch) for 1 in. gauge ...........eeeeenennerere reee
Feed (lower) Dog 16 teeth {10 teeth to the
inch} for 1-1/8 in. and 1-1/4 in. gauges...
ETIENNE
18
No.
58415
1770
19762
58284
565C
15133
58390
58391
19819
346E
1861
1015C
1503E
294C
1503E
19967
2022
134E
11375
568E
50322D
58392
58393
58235
346E
1015C
1503E
294C
PARTS FOR MACHINE No. 7-61
Plate
22819
NOTE:
22817
22810
22810
22810
22815
22815
22815
22815
22815
22815
22815
22815
22815
22815
22815
22810
22810
22810
22815
=. ож =
22815
22815
22815
22815
22815
Nome
Feed (lower) Dog 16 teeth (10 teeth to the
inch) for 1-3/8 in. and 1-1/2 in, gauges
When ordering Nos. 58414 and 58415,
stote gauge required.
Feed {lower} Dog Screw (4) .................e......
Feed (lower) Forked Connection ..............
Feed (lower) Forked Connection 19762
with 11368, 11375, 50322D and two each
565C and 1513) overcentre conan
Feed flower) Forked Connection Hinge
SCLOW .......eveneriareeererecorerpeercanan ne amena amen neon nacen.
Feed (lower) Forked Connection Hinge
Feed (lower) Lifting Rock Shaft with 134E,
2022 and 19967 .......e......00emrreninorcocnnercanenenecace
Feed (lower) Lifting Rock Shaft complete,
Nos. 58390 and two 19819 ...........e...e.eeremanaona
Feed (lower) Lifting Rock Shaft Crank
with 346E and 1861 (2) -e.........mene20smemnannanes
Feed (lower) Lifting Rock Shaft Crank
Clamping Screw (2) .............-—.........e..00.esemonves
Feed (lower) Lifting Rock Shoft Crank
Roller and Stud (2) ...............—0=. e... nen
Feed (lower) Lifting Rock Shaft Screw
Center (left) ......
Feed (lower) Lifting Rock Shaft Scrow
Center (left) Nut
Feed (lower) Lifting Rock Shaft Screw
Center (right) .........—...—......0nexennenenacnanenaner econ.
Feed (lower) Lifting Rock Shaft Screw
Center {right} Nut riers
Feed (lower) Lifting Rock Shaft Wearing
Block TEO
Feed (lower) Lifting Rock Shaft Wearing
Block Position Pin vinnie
Feed (lower) Lifting Rock Shaft Wearing
Block Screw ........... .—.ereenonieneinenenenemanaaom enana
Feed (lower) Regulator ..............e_ e... em...
Feed (lower) Regulator Hinge Screw ..........
Feed (lower) Reguiator Thumb Screw ........
Feed (lower) Rock Shaft ............ e... 2...
Feed (lower) Rock Shaft complete, Nos.
58235 and 58392 .................ese=ecesneezvenrer rene.
Feed (lower) Rock Shaft Crank with 346E
Feed (lower) Rock Shaft Crank Clamping
SCrOW iriver reset erst re rere rere enn
Feed (lower) Rock Shaft Screw Center
(left) rerio rene eseerarorane reee ra re amero ree
Feed (lower) Rock Shaft Screw Center
(left) Nut ...... eee... mmeeconneninimenecenemenecamanee ene
Feed (lower) Rock Shaft Screw Center
(right) .... peninaroo-eneaaver o meconerema ramo.
No.
1503E
19669
19670
58348
19671
19672
58349
58350
190E
2117
456AL
19673
58351
159D
1340
19674
145Е
19675
3810
795C
445C
44BAL
1520E
23D
58511
445C
19527
65D
PARTS FOR MACHINE No. 7-61 19
Piate Name
22815 Feed (lower) Rock Shaft Screw Center
(right) NUt ce
22821 Feed (upper) Bar .............2...irnienemeeneneeone ere
22822 Feed (upper) Bar Guide Bracket (lower)
with 456AL for 19671 iii snnre
22823 Feed (upper) Bar Guide Bracket (lower)
with 456AL for 58349 ........ coe
---—-- Feed (upper) Bar Guide Bracket (lower)
complete for 3/4 in. to 1-1/8 in. gauge,
Nos. 19670, 19672 and two 190E ..............
22822 Feed (upper) Bar Guide Bracket (lower)
Cop ..….….…ese ee...
commana Feed (upper) Bar Guide Bracket (lower)
complete for 1-1/4 in. to 1-1/2 in. gauge
Nos. 58348, 58350 and two 190 Е ..............
22823 Feed (upper) Bar Guide Bracket (lower)
; Cap = L.acrcececseranceneennnseness sara rne enter a ra c nan ce
22823 Feed (upper) Bar Guide Brocket (lower)
Cap Screw (2) …….…-.-1…cnrssrenennnee caarasenansn an cran vers
22823 Feed (upper) Bar Guide Bracket (lower)
Pin ves
22823 Feed (upper) Bar Guide Bracket (lower)
Set Screw .. pen.
22820 Feed (upper) Bar Guide Bracket (upper)
for 3/4 in. to 1-1/8 in. gouge к...
22821 Feed (upper) Bar Guide Bracket (upper)
with 11424 for 1-1/4 in. to 1-1/2 in. gauge
22821 Feed (upper) Bar Guide Bracket (upper)
Screw (back) coin nene
22821 Feed {upper) Bar Guide Bracket (upper)
Screw (front) .........
22821 Feed (upper) Bar Hinge Bracket with VASE,
795C and two 445C reece nee
22821 Feed (upper) Ber Hinge Bracket Adjusting
Фес МУ 2reneiriereirenenrrocenaroaconennteamenea ea emameanammanmma
22824 1+Feed (upper) Bar Hinge Bracket Guide
Plate ........... Gesca caca ea ea raro aca eee
22824 Feed (upper) Bar Hinge Bracket Guide
Plate Screw (2) ....…...……..currerecmeemeennesenennnnnn
22821 Feed (upper) Bar Hinge Bracket Set Screw
(ong) .. KR ERARARTARELKTREEFRAKEEFER
22821 Feed (upper) Bar Hinge Bracket Set Screw
(short) (2) - .. ve
22821 Feed (upper) Bar Hinge Bracket Support
SE IBW ..i.emeneneneranaainiora narran en enre ren anecaaanenenacce nacen
22821 Feed (upper) Bar Hinge Bracket Support
Screw Nut .........—... arersneren sera cannes
22821 Feed (upper) Bar Hinge Screw araranener ee reseau ee
22810 Feed (upper) C