advertisement
4-180-168-11(1)
LCD
Digital Colour TV
Operating Instructions
Setting Up
Watching TV
Additional Information
KDL-40EX43B / KDL-32EX43B
NOTICE FOR
CUSTOMERS IN
THE UNITED
KINGDOM
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced with the same rating of fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used.
When an alternative type of plug is used it should be fitted with the same rating of fuse, otherwise the circuit should be protected by a 10 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse.
Never use the plug without the fuse cover.
If you should lose the fuse cover, please contact your nearest Sony service station.
FUSE
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
Please refer to the illustration that actually equipped with the product.
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual thoroughly and retain it for future reference.
The manufacturer of this product is
Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075 Japan.
The Authorized Representative for
EMC and product safety is Sony
Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.
Notes on Digital TV function
• Any functions related to Digital TV
( ) will only work in countries or areas where DVB-T (MPEG-2 and
H.264/MPEG-4 AVC) digital terrestrial signals are broadcast or where you have
2
GB access to a compatible DVB-C (MPEG-
2 and H.264/MPEG-4 AVC) cable service. Please confirm with your local dealer if you can receive a DVB-T signal where you live or ask your cable provider if their DVB-C cable service is suitable for integrated operation with this TV.
• Your cable provider may charge a fee for their services, or require you to agree to its terms and conditions of business.
• This TV set complies with DVB-T and
DVB-C specifications, but compatibility with future DVB-T digital terrestrial and
DVB-C digital cable broadcasts are not guaranteed.
• Some Digital TV functions may not be available in some countries/areas and
DVB-C cable may not operate correctly with some providers.
For a list of compatible cable providers, refer to the support web site: http://support.sony-europe.com/TV/
DVBC/
~
• Instructions about “Installing Wall
Mount Bracket” are included within this
TV’s instructions manual.
• The illustrations used in this manual are of the KDL-40EX43B unless otherwise state.
Trademark information
is a registered trademark of the DVB
Project.
HDMI, the HDMI logo and High-
Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
DLNA and DLNA CERTIFIED are trademarks and/or service marks of Digital
Living Network Alliance.
DivX® is a video file compression technology, developed by DivX, Inc.
DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,Inc.
This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into
DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified® device must be registered in order to play DivX Video-on-
Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
“BRAVIA” and are trademarks of Sony Corporation.
“XMB
™
” and “XrossMediaBar” are trademarks of Sony Corporation and Sony
Computer Entertainment Inc.
“Blu-ray Disc”, “Blu-ray” and “Blu-ray
Disc” logo are trademarks of Blu-ray Disc
Association.
is a trademark of DVD Format/Logo
Licensing Corporation.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and
Sony Corporation.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.
“BD-LIVE,” “BD-LIVE” logo, and
“BONUSVIEW” are trademarks of Bluray Disc Association.
Manufactured under license under U.S.
Patent #’s: 5,451,942; 5,956,674;
5,974,380; 5,978,762; 6,487,535 & other
U.S. and worldwide patents issued & pending. DTS and DTS 2.0 + Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS,
Inc. © 1996-2008 DTS, Inc. All Rights
Reserved.
Location of the identification label
Labels for Model No. and Power Supply rating (in accordance with applicable safety regulation) are located on the rear of the TV.
Table of Contents
Setting Up
Watching TV
Additional Information
Checking the accessories
Remote (1)
Size AAA batteries (R3 type) (2)
Table-Top Stand (1)*
Fixing screws for Table-Top Stand
(M5 × 16) (4)
Assembling screws for Table-Top Stand
(M5 × 16) (4)
* Assemble the Table-Top Stand with the supplied assembling screws. Refer to the supplied Table-
Top Stand leaflet to assemble the stand.
Inserting batteries into the remote
Push and lift the cover to open.
3
GB
Setting Up
Attaching the Table-Top
Stand
1
Refer to the supplied Table-Top Stand leaflet for proper attachment for some
TV models.
2
Place the TV set on the Table-Top
Stand.
Connecting an antenna
(aerial)/Set Top Box/ recorder (e.g. DVD recorder)
Connecting a Set Top Box/recorder
(e.g. DVD recorder) with SCART
3
Fix the TV to the Table-Top Stand according to the arrow marks that guide the screw holes using the supplied screws.
Set Top Box/recorder (e.g. DVD recorder)
Connecting a Set Top Box/recorder
(e.g. DVD recorder) with HDMI
~
• If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m {15 kgf·cm}.
1
IN
ARC
Set Top Box/recorder (e.g. DVD recorder)
4
GB
Preventing the TV from toppling over
Organising the AC power cord (mains lead)
1
Install a wood screw (4 mm in diameter, not supplied) in the TV stand.
2
Install a machine screw (M4 × 16, not supplied) into the screw hole of the TV.
3
Tie the wood screw and the machine screw with a strong cord (not supplied).
5
GB
Performing the initial set-up Detaching the Table-Top
Stand from the TV
~
• Remove the screws guided by the arrow marks of the TV.
• Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV.
1
Connect the TV to your AC power outlet (mains socket).
2
Press 1 on the TV.
When you switch on the TV for the first time, the Language menu appears on the screen.
3
Follow the instructions on the screen.
Digital Auto Tuning: When you select
“Cable”, we recommend that you select
“Quick Scan” for quick tuning. Set
“Frequency” and “Network ID” according to the information supplied from your cable provider. If no channel is found using
“Quick Scan”, try “Full Scan” (though it may take some time).
For a list of compatible cable providers, refer to the support web site: http://support.sony-europe.com/TV/
DVBC/
Programme Sorting: Changes the order of analogue channels stored in the TV.
1
Press F/f to select the channel you want to move to a new position, then press .
2 Press F/f to select the new position for the channel, then press .
~
• You can also tune channels manually.
6
GB
Watching TV
To watch programmes
1
Turn on the TV.
2
GUIDE
OPTIONS
HOME
2
Press 1 on the TV to turn on the TV.
Select a mode.
3
Select a TV channel.
3
Using Digital Electronic Programme
Guide
Press GUIDE in digital mode to display the programme guide.
z
• The number 5, N, PROG + and AUDIO buttons on the remote have a tactile dot.
Use the tactile dots as a reference when operating the TV.
To utilise the TV’s features
HOME button
Press to display various operation and setting screens.
Settings
System Settings
OPTIONS button
Press to display convenient functions based on the current input or content.
Picture
Sound
BRAVIA ENGINE 3 PRO
Add to Favourites
Lock/Unlock
PAP
Motionflow
Sleep Timer
Headphone Volume
Speaker
System Information
TV
(Continued)
7
GB
To use i-Manual
1
2
Operating instructions are built into your BRAVIA
TV and can be displayed on the screen.
To learn more about your TVs features you can access your i-Manual with the touch of a button.
1
Press i-MANUAL.
2
Press
G/g/F/f/
to select items.
x Welcome to i-Manual x “BRAVIA” TV Features x Watching TV
Introduces convenient features such as EPG
Guide, Favourites, etc.
x Playing a Disc x Using the Home Menu
Customise your TV settings, etc.
x Fun Features with Connected x x
Equipment
Introduces how to connect optional equipment.
Parts Description x Troubleshooting
Find solutions for your problem.
Index
~
• Images and illustrations may differ from what is displayed on the screen.
8
GB
Playing a disc
Playback
The Playback feature allows you to play a desired disc by simply inserting it into the disc slot.
1
Insert a disc into the slot with the playback side facing away from you.
2
For a video disc, playback starts automatically.
For a music or photo disc, select from the “Music” or “Photo” category in the “XMB” and press .
~
• If playback does not start automatically, select from the “Video” category in the “XMB” and press .
9
GB
Additional Information
Troubleshooting
Check whether the 1 (standby) indicator is flashing in red.
When the 1 (standby) indicator is flashing
The self-diagnosis function is activated.
1
Count how many times the 1 (standby) indicator flashes between each three second break.
For example, the indicator may flash three times, go off for three seconds, then flash again three times.
2
Press 1 on the TV to turn it off, disconnect the AC power cord (mains lead), and inform your dealer or Sony service centre of how the indicator flashes (number of flashes).
When the 1 (standby) indicator is not flashing
1
Check the items in the tables below. (Also refer to “Troubleshooting” in the i-Manual.)
2
If the problem persists, have your TV serviced by qualified service personnel.
Condition Explanation/Solution
Picture
There is no picture (screen is dark) and no sound.
• Check the antenna (aerial)/cable connection.
• Connect the TV to the AC power (mains), and press 1 on the TV.
• If the 1 (standby) indicator lights up in red, press "/1.
Tiny black points and/or bright points appear on the screen.
• The screen is composed of pixels. Tiny black points and/or bright points (pixels) on the screen do not indicate a malfunction.
General
The TV turns off automatically (the TV enters standby mode).
• Check if the “Sleep Timer” is activated, or confirm the
“Duration” setting of “On Timer”.
• Check if the “Idle TV Standby” is activated.
The remote does not function.
• Replace the batteries.
• Your TV may be in SYNC mode.
Press SYNC MENU, select “TV Control” and then select “Home
(Menu)” or “Options” to control the TV.
The “Parental Lock”/
“Parental Control Settings” password has been
• Enter 9999 for the PIN code after selecting “PIN Code” in
“Parental Lock” of “System Settings” in the “Settings” menu.
(PIN code 9999 is always accepted.) forgotten.
Sound is heard when turning on the TV or inserting a disc into the built-in BD player.
• It is a sound of the built-in BD player working and not a malfunction.
10
GB
Specifications
System
Panel system
TV system
Colour/video system
Channel coverage
LCD (Liquid Crystal Display) Panel
Analogue: Depending on your country/area selection: B/G/H, D/K, L, I
Digital: DVB-T2/DVB-T/DVB-C
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC MP/HP@L4
Analogue: VHF: E2–E12/UHF: E21–E69/CATV: S1–S20/HYPER: S21–S41
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69
Digital: VHF/UHF
10 W + 10 W Sound output
Input/Output jacks
Antenna (aerial) cable
/ AV1, 2
75 ohm external terminal for VHF/UHF
21-pin scart connector (CENELEC standard) including audio/video input, RGB input and TV audio/video output.
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i COMPONENT IN
COMPONENT IN Audio input (phono jacks)
HDMI IN1, 2, 3 Video: 1080/24p, 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
Analogue audio input (minijack) (HDMI IN 1 only)
Video input (phono jack) AV3
AV3 Audio input (phono jacks)
DIGITAL AUDIO OUT
(OPTICAL)
Digital optical jack (Two channel linear PCM, Dolby Digital, DTS Digital)
(VAR/FIX)
PC IN
Audio output (phono jacks)
PC Input (Mini D-sub 15-pin)
PC audio input (minijack)
USB port i
LAN
EXT
Headphones jack
CAM (Conditional Access Module) slot
10BASE-T/100BASE-TX connector (Depending on the operating environment of the network, connection speed may differ. 10BASE-T/100BASE-TX communication rate and communication quality are not guaranteed for this TV.)
* For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).
External memory slot (For connecting the USB memory)
DC output: 5 V 500 mA Max
(Continued)
11
GB
Model name KDL-
Power and others
Power requirements
Screen size (measured diagonally)
Display resolution
Power consumption in “Home”/
“Standard” mode in “Shop”/
“Vivid” mode
40EX43B
220 V – 240 V AC, 50 Hz
Approx. 101.6 cm/40 inches
1,920 dots (horizontal) × 1,080 lines (vertical)
107 W
176 W
Standby power consumption*
1
Average annual energy consumption*
2
Laser
0.2 W (17 W when “Quick Start” is set to “On”)
156 kWh without Table-Top Stand
Mass (Approx.)
Type: Semiconductor, continuous
BD Wavelength: 400 - 410 nm
Power: Max 20 mW
DVD Wavelength: 650 - 663 nm
CD
Power: Max 7 mW
Wavelength: 770 - 800 nm
Power: Max 7 mW
Dimensions (Approx.) (w × h × d) with Table-Top Stand 99.2 × 63.6 × 28.0 cm
99.2 × 59.8 × 11.6 cm
18.0 kg with Table-Top Stand without Table-Top Stand
Supplied accessories
Optional accessories
Operating temperature
15.1 kg
See “Checking the accessories” (page 3).
Wall-Mount Bracket: SU-WL500
5 ºC to 35 ºC (41 °F to 95 °F)
32EX43B
Approx. 80.1 cm/32 inches
72 W
128 W
0.2 W (17 W when “Quick Start” is set to “On”)
105 kWh
80.0 × 53.4 × 25.0 cm
80.0 × 49.7 × 11.3 cm
13.2 kg
11.2 kg
*
1
*
2
Specified standby power is reached after the TV finishes necessary internal processes.
4 hours a days and 365 days a year
~
• To save power consumption
– when you reduce backlight setting (the brightness of the screen), the power consumption reduce.
– the “Eco” settings (e.g. “Power Saving”, “Idle TV Standby”) help you to reduce the power consumption and thus save money by reducing electricity bills.
Design and specifications are subject to change without notice.
12
GB
Installing the Accessories (Wall-Mount Bracket)
To Customers:
For product protection and safety reasons, Sony strongly recommends that installing of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of this product.
Your TV can be installed using the SU-WL500 Wall-Mount Bracket (sold separately).
• Do not install the TV in an inclined position. It is designed to be operated in a vertical position only. Eject and take out any disc from the built-in BD player before installing the TV on a wall.
• Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the installation.
•
Refer to “Detaching the Table-Top Stand from the TV” (page 6).
~
• Place the TV on the Table-Top Stand, when securing the Mounting Hook.
Screw
(+PSW
6 × 16)
Square hole
Mounting Hook
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.
(Continued)
13
GB
TV installation dimensions table
Screen centre point
Model Name
KDL-
Display dimensions Screen centre dimension
40EX43B
32EX43B
A
99.2
80.0
B
59.8
49.7
C
12.2
17.2
Figures in the above table may differ slightly depending on the installation.
Unit: cm
Length for each mounting angle
Angle (0
°)
D E
42.5
16.0
42.6
15.7
WARNING
The wall that the TV will be installed on should be capable of supporting a weight of at least four
times that of the TV. Refer to “Specifications” (page 12) for its weight.
14
GB
Screw and Hook locations diagram/table
KDL-40EX43B
KDL-32EX43B
Model Name
Screw location
When installing the Mounting Hook on the
TV.
Screw location d, g e, g
Hook location b c
Hook location
When installing the TV onto the Base Bracket.
a b c
*
* Hook location “a” cannot be used for the models.
15
GB
Safety
Information
Installation/Set-up
Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.
Installation
• The TV set should be installed near an easily accessible mains socket.
• Place the TV set on a stable, level surface.
• Only qualified service personnel should carry out wall installations.
• For safety reasons, it is strongly recommended that you use Sony accessories, including:
– Wall-mount bracket SU-WL500
• Be sure to use the screws supplied with the Wall-mount bracket when attaching the mounting hooks to the TV set. The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook.
The diameter and length of the screws differ depending on the Wall-mount bracket model.
Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.
8 mm - 12 mm
Screw (supplied with the
Wall-mount bracket)
Mounting Hook
Hook attachment on rear of TV set
Transporting
• Before transporting the
TV set, disconnect all cables.
• Two or three people are needed to transport a large
TV set.
• When transporting the TV set by hand, hold it as shown on the right. Do not put stress on the LCD panel and the frame around the screen.
• When lifting or moving the TV set, hold it firmly from the bottom.
• When transporting the TV set, do not subject it to jolts or excessive vibration.
• When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.
Ventilation
• Never cover the ventilation holes or insert anything in the cabinet.
• Leave space around the TV set as shown below.
• It is strongly recommended that you use a Sony wall-mount bracket in order to provide adequate air-circulation.
Installed on the wall
30 cm
10 cm 10 cm
10 cm
Leave at least this space around the set.
Installed with stand
30 cm
10 cm 10 cm 6 cm
Leave at least this space around the set.
• To ensure proper ventilation and prevent the collection of dirt or dust:
– Do not lay the TV set flat, install upside down, backwards, or sideways.
– Do not place the TV set on a shelf, rug, bed or in a closet.
– Do not cover the TV set with a cloth, such as curtains, or items such as newspapers, etc.
– Do not install the TV set as shown below.
Air circulation is blocked.
Wall Wall
Mains lead
Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:
– Use only mains leads supplied by
Sony, not other suppliers.
– Insert the plug fully into the mains socket.
– Operate the TV set on a 220-240 V AC supply only.
– When wiring cables, be sure to unplug the mains lead for your safety and take care not to catch your feet on the cables.
– Disconnect the mains lead from the mains socket before working on or moving the TV set.
– Keep the mains lead away from heat sources.
– Unplug the mains plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate, which could result in a fire.
Notes
• Do not use the supplied mains lead on any other equipment.
• Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken.
• Do not modify the mains lead.
• Do not put anything heavy on the mains lead.
• Do not pull on the mains lead itself when disconnecting the mains lead.
• Do not connect too many appliances to the same mains socket.
• Do not use a poor fitting mains socket.
Prohibited Usage
Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.
Environment:
Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The
TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.
Situation:
Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer.
Disconnect the TV set from mains socket and aerial during lightning storms.
Broken pieces:
• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.
• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.
Condensation
If the TV is brought directly from a cold to a warm location, or is placed in a very damp room, or is placed in a room in which heating has just been turned on, moisture may condense on the surface or inside the TV. Should this occur, turn off the TV and leave the TV off until the moisture evaporates, and then the TV can be used. If a disc is inserted in the built-in
BD player, eject and take out the disc and turn off the TV. Using the TV with moisture in or on it may cause the TV to show poor picture and/or poor colour or may cause a malfunction.
16
GB
When not in use
• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.
• As the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to disconnect the TV set completely.
• However, some TV sets may have features that require the TV set to be left in standby to work correctly.
For children
• Do not allow children to climb on the
TV set.
• Keep small accessories out of the reach of children, so that they are not mistakenly swallowed.
• Be sure small children do not put hands into the disc slot. It may cause injury.
If the following problems occur...
Turn off the TV set and unplug the mains lead immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it checked by qualified service personnel.
When:
– Mains lead is damaged.
– Poor fitting of mains socket.
– TV set is damaged by being dropped, hit or having something thrown at it.
– Any liquid or solid object falls through openings in the cabinet.
Warning
To prevent the spread of fire, keep candles or other open flames away from this product at all time.
Precautions
Viewing the TV
• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.
• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.
LCD Screen
• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light
(red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.
• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.
• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.
• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.
• The LCD screen contains a small amount of liquid crystal. Some fluorescent tubes used in this TV set also contain mercury. Follow your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/cabinet of the TV set
Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning.
To avoid material degradation or screen coating degradation, observe the following precautions.
• To remove dust from the screen surface/ cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.
• Do not spray water or detergent directly on the TV set. It may drip to the bottom of the screen or exterior parts, and may cause a malfunction.
• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.
• Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.
• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand.
Optional Equipment
• Keep optional components or any equipment emitting electromagnetic radiation away from the TV set.
Otherwise picture distortion and/or noisy sound may occur.
• This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection signal cable shorter than 3 meters.
Batteries
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix old and new batteries.
• Dispose of batteries in an environmentally friendly way. Certain regions may regulate the disposal of batteries. Please consult your local authority.
• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.
Disposal of the TV set
Disposal of Old
Electrical &
Electronic
Equipment
(Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local
Civic Office, your household waste disposal service or the shop where you purchased the product.
Disposal of waste batteries
(applicable in the
European Union and other
European countries with separate collection systems)
This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
17
GB
Safety information about built-in BD player
• The use of optical instruments with this product will increase eye hazard. As the laser beam used in this built-in BD/DVD player is harmful to eyes, do not attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
• Do not use solvents such as benzine, thinner, commercially available disc/ lens cleaners, or anti-static spray intended for vinyl LPs.
• If you have printed the disc’s label, dry the label before playing.
• Do not force a disc into the disc slot.
When there is already a disc inside the built-in BD player, trying to insert another disc may cause malfunction.
• Sound may jump or picture distortion may occur if a lens is dirty with dust. For repair, contact the shop from which the product was purchased or a customer information service centre.
This label is located on the laser protective housing inside the enclosure.
This appliance is classified as a CLASS
1 LASER product. The CLASS 1
LASER PRODUCT MARKING is located on the laser protective housing inside the enclosure.
• To keep the disc clean, handle the disc by its edge. Do not touch the surface.
Dust, fingerprints, or scratches on the disc may cause it to malfunction.
Precautions about built-in BD player
• The TV has a region code located on the rear of the unit.
• Do not use cleaning discs or disc/lens cleaners (including wet or spray types).
These may cause the apparatus to malfunction.
• When ejecting a disc, the disc may hit objects and cause damage or injury.
Keep an open space around the disc slot.
• Take out any discs from the built-in BD player when you move the TV. If you don’t, the disc may be damaged. Eject and take out the disc before moving the
TV.
• Do not pull out the AC power cord
(mains lead) while the built-in BD player is playing.
• Do not use the following discs.
– A lens cleaning disc.
– A disc that has a nonstandard shape
(e.g., card, heart).
– A disc with a label or sticker on it.
– A disc that has cellophane tape or sticker adhesive on it.
• Do not resurface the playing side of a disc to remove surface scratches.
• When ejecting a disc from the built-in
BD player by pressing Z on the TV, be sure to take out the disc from the disc slot. Do not leave the disc in the disc slot.
• Eject and take out the disc from the disc slot and turn off the TV when not using the TV.
• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the centre out.
18
GB
Keep this Instruction manual safe you’ll need it
Television in the UK is going digital, bringing us all more.
Please see overleaf to find out when your area switches to digital.
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover in the UK. Digital UK provides impartial information on what people need to do to prepare for the move to digital, and when they need to do it.
How the switchover affects your TV equipment:
Your new TV has a digital tuner built in, which means it is ready to receive the Freeview signal by simply plugging it into your aerial socket (check if you can get digital TV through your aerial now, or whether you'll have to wait until switchover, at www.digitaluk.co.uk).
When the TV switchover happens in your area, there are at least two occasions when you will need to re-tune your TV in order to continue receiving your existing TV channels, and also to pick up new ones. Digital UK, the body leading the digital TV switchover, will advise you when you need to retune during the switchover.
19
GB
How to re-tune:
1 Press "HOME" on the remote
2 Press G/g to select "Settings"
3 Press F/f to select "Digital Set-up", then press
4 Press to select "Digital Auto Tuning"
5 Press G to select "Yes" then press to start "Digital Auto Tuning"
6 Follow the on screen instructions.
If you are missing any channels, it may be that they are not available in your area, or that your aerial needs upgrading.
If you have any questions, please contact Sony on 08705 111 999 or call Digital UK on 0845 6 50 50
50 or visit www.digitaluk.co.uk
20
GB
†Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends.
Rates may vary for calls from non-BT lines.
For useful information about Sony products
© 2010 Sony Corporation
4-180-168-11(1)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement