FLOOR POLISHER

MODELS:

U17X-10090590 SP17-10090240

U20X-10090610 SP20-10090310

UDS20-10090630 SP17X-10090280

SP20X-10090320

SPDS20-10090350

SP17XIE-10090300

SP17XIA-10090290

SPDS17IE-10090340

SPDS17IA-10090330

SP17HDIE-10090250

IPX4

Operating Instructions (ENG)

86309580-A

10/08/08

MACHINE DATA LOG/OVERVIEW

Model:

Date of Purchase:

Serial Number:

Sales Representative:

Address:

Phone Number:

2

86309580 FLOOR POLISHER 10/08/08

TABLE OF CONTENTS

Machine Data Log............................. 2

Table of Contents.............................. 3

HOW TO USE THIS MANUAL

How to use this Manual..................... 1-1

SAFETY

Important Safety Instructions ............ 2-1

Hazard Intensity Level. ..................... 2-2

Grounding Instructions 120V. ........... 2-3

Grounding Instructions 230V ............ 2-4

Safety Label Location ....................... 2-5

OPERATION

Technical Specifications ................... 3-1

Handle Installation

............................

3-2

Controls............................................. 3-3

Handle Adjustment............................ 3-3

Machine Operation

............................

3-4

Pad Driver Installation....................... 3-4

MAINTENANCE

Scrub Brush/Pads ............................. 4-1

Machine Troubleshooting.................. 4-2

GROUP PARTS LIST

Brush/Pad Driver Group.................... 5-1

Electrical – 120v................................ 5-3

Electrical – 230v................................ 5-5

Deck.................................................. 5-7

Handle............................................... 5-9

Motor................................................. 5-11

Wiring-120V ...................................... 5-13

Wiring-230V ...................................... 5-15

Suggested Spare Parts..................... 5-14

86309580 FLOOR POLISHER 10/08/08

3

HOW TO USE THIS MANUAL

This manual contains the following sections:

- HOW TO USE THIS MANUAL

-

SAFETY

-

OPERATIONS

- MAINTENANCE

- PARTS LIST

The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.

Parts may be ordered from authorized dealers.

When placing an order for parts, the machine model and machine serial number are important.

Refer to the MACHINE DATA box which is filled out during the installation of your machine. The

MACHINE DATA box is located on the inside of the front cover of this manual.

The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards are identified that could result in product or personal injury, or severe injury resulting in death.

The OPERATIONS section is to familiarize the operator with the operation and function of the machine.

The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order:

The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:

-

REF –

column refers to the reference number on the parts illustration.

-

PART NO.

– column lists the part number for the part.

-

PRV NO.

- Reference No.

-

QTY

– column lists the quantity of the part used in that area of the machine.

-

DESCRIPTION

– column is a brief description of the part.

-

SERIAL NO. FROM

– If this column has an (*) and a Reference number, see the SERIAL NUMBERS page in the back of your manual. If column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.

-

NOTES

– column for information not noted by the other columns.

NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.

NOTE: The number on the lower left corner of the front cover is the part number for this manual.

1-1

86309580 FLOOR POLISHER 10/08/08

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

To reduce the risk of fire, electric shock, or injury:

Use only

indoors. Do not use outdoors or expose to rain.

Use only

as described in this manual. Use only manufacturer’s recommended components and attachments.

If the machine is

not working properly

, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.

Do not

operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

Machine can cause a fire

when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs

must be done

by qualified personnel.

During operation

, attention shall be paid to other persons, especially children.

The machine shall only

be operated by instructed and authorized persons.

When leaving unattended

, unplug the machine.

Do not

handle the plug or machine with wet hands.

Do not

unplug machine by pulling on cord. To unplug, grasp the plug, not the cord.

Do not

use with damaged cord or plug. Follow all instructions in this manual concerning grounding the machine.

Do not

pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not

pull/run machine over cord.

Keep

cord away from heated surfaces.

Connect to a

properly

grounded outlet. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

86309580 FLOOR POLISHER 10/08/08

2-1

SAFETY

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words –

WARNING

and

CAUTION

and

FOR SAFTEY.

The level of hazard intensity is determined by the following definitions:

WARNING –

Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION –

Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and Understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose fitting clothing, jackets, shirts, or sleeves when working on the machine. Use approved replacement parts.

2-2

86309580 FLOOR POLISHER 10/08/08

SAFETY

GROUNDING INSTUCTIONS-120V

THIS PRODUCT IS FOR COMMERCIAL USE

ONLY.

ELECTRICAL:

In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in “Fig. A”. A temporary adaptor that looks like the adaptor in “Fig . C” may be used to connect this plug to a 2-pole receptacle as shown in “Fig. B”, if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.

Grounding Pin

Grounded

Outlet

FIGURE A

GROUNDING CONNECTION

USING AN ADAPTOR

Metal Screw

Tab for Grounding

Screw

Adaptor

Grounded

Outlet Box

FIGURE B

Adaptor

FIGURE C

Note: Adaptors are not allowed in Canada.

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

86309580 FLOOR POLISHER 10/08/08

2-3

SAFETY

GROUNDING INSTRUCTIONS-230V

THIS PRODUCT IS FOR COMMERCIAL USE

ONLY.

ELECTRICAL:

The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the

motors.

EXTENSION CORDS:

If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet

(15.5m) in length.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.

This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

2-4

86309580 FLOOR POLISHER 10/08/08

SAFETY

SAFETY LABEL LOCATION

NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement.

WARNING LABEL

P/N 86219740

PRV NO. 500194

86309580 FLOOR POLISHER 10/08/08

2-5

TECHNICAL SPECIFICATIONS

ITEM DIMENSION/CAPACITY/MODEL

CONSTRUCTION

Heavy-duty die cast aluminum deck with heavyduty rubber bumper, tubular steel adjustable handle with die cast aluminum handle housing

MOTOR

1HP 115V induction

1.5HP 115V induction

1.75 HP 115V 175/300RPM

1HP 230V induction

1.5 HP 230V induction

1.75 HP 230V 175/300RPM

BRUSH/PAD SPEED

SP13, SP15, SP17, U17, SP17, SP20, U20

SP17X, U17X, SPT20X, SP20X, U20X

SPDS20, UDS20

SP17IA, SP17IE

SP17HDIE, SP17XIA, SP17XIE

SPDS17IA, SPDS17IE

175 rpm

146 rpm 230V

175/300 rpm

ELECTRICAL SYSTEM

SP13, SP15, SP17, U17, SP17, SP20, U20,

SP17X, U17X, SPT20X, SP20X, U20X

SP17HDIE , SP17IA, SP17IE, SP17XIA,

SP17XIE

UDS20, SPDS20, SPDS17IA, SPDS17IE

115 volts, 60 Hz

230 volts, 50Hz

SP13, SP15,, SP17, U17,SPT17, SP17X, U17X,

SP20, U20, SPT20X, SP20X, U20X,

SPDS20, USD20

SP17HDIE, SP17XIA, SPX17IE, SPDS17IE,

SP17IA, SP17XIA, SPDS17IA

CABLE

50’ (15 m), 14/3, built in cord wrap

75’ (22.9) 1.5mm³, built in cord wrap

SWITCHES

WHEELS

HANDLE

SP13, SP15,, SP17, U17,SPT17, SP17X, U17X,

SP20, U20, SPT20X, SP20X, U20X,

SPDS20, USD20

SP17HDIE, SP17XIA, SPX17IE, SPDS17IE,

SP17IA, SP17XIA, SPDS17IA

Dual levers with safety lock

Two 5” (12.7 cm) dia., 1.25” (3 cm) wide, nonmarking tread

1.5” (4 cm) tubular steel, adjustable, easy to use thumb activated safety lock

DIMENSIONS (L X W X H)

13” (33 cm) model

15” (38 cm) model

17” (43 cm) model

20” (51 cm) model

21.0” (53 cm) x 14” (36 cm) x 47” (119 cm)

22.0” (56 cm) x 16” (41 cm) x 47” (119 cm)

23.0” (58 cm) x 18” (46 cm) x 47” (119 cm)

24.5” (62 cm) x 21” (53 cm) x 47” (119 cm)

3-1

86309580 FLOOR POLISHER 10/08/08

HANDLE INSTALLATION

WHEN INSTALLING THE HANDLE

ASSEMBLY, CHECK ORIENTATION OF

THE CORD ASM AND CORD HOOK.

4

DECK

ASSEMBLY

5

6

MOTOR PLUG

RECEPTACLE

MOTOR

PLUG

PIVOT

HOLE

3

1

(SEE NOTE)

2

The handle must be installed by qualified personnel. Read all instructions thoroughly. The machine is shipped with handle unassembled.

The machine is shipped with handle unassembled.

Follow these steps for installation:

1. Remove handle and deck assembly from carton.

2. Attach handle assembly to base using hardware kit

(86219680-PRV NO. 47331)

(attached to handle in a plastic bag) items 1, 2, and 3.

NOTE: The spacers (items 1) are required for the correct operation of the handle. The spacers are positioned completely inside the pivot holes in the casting, and are held in place by tightening the bolts and washers (items 2 and 3) against the spacer.

3. Remove bolt, nut and washers (items 4, 5 and 6) from lower block on handle assembly. Attach links as shown. Tighten bolt and nut securely, then back off 1/4 to 1/2 turn.

4. Check handle for movement up and down.

5. Plug motor cord into handle cord receptacle.

86309580 FLOOR POLISHER 10/08/08

3-2

OPERATION

CONTROLS

1. Safety Lock –

Prevents unintended operation of the machine.

2. Switch Levers –

Turns machine on/off.

adjusted to a comfortable operating position.

1

2

3

2

NOTE: It is incorrect to make it lock opposite from the way it was assembled by

applying more force to the nut.

The pivot pin is off center in relationship to the axis of the handle. To adjust handle, tighten nut on handle while in the locked position. The handle is locked when the screw is to the outside of the machine and the flat on the opposite side of the handle is flush to the bracket.

PIVOT PIN

HANDLE

LOCKING SIDE FLAT

HANDLE HEIGHT ADJUSTMENT

NOTE: The handle is in the up, locked position from the factory.

1

3

2

4

3-3

The handle adjust bar (1) for the polishers are individually preset at the factory for optimum locking efficiency and minimum effort of engaging. It should not be necessary to adjust the handle adjust bar unless the handle adjustment bar (1) the washer (3) and nut (2) have been disturbed.

86309580 FLOOR POLISHER 10/08/08

MACHINE OPERATION

For indoor use only.

When using the pad, always keep the machine moving when in contact with the floor.

High starting torque. Hold machine firmly with both hands.

1. Ensure that the pad driver is in good shape.

Install or change pad if necessary.

2. Plug the machine into a wall outlet as described in the grounding instructions.

3. Lower the handle by unlocking the adjustment handle and moving the handle into position.

Relock the handle when it is in a comfortable position.

Insure that handle is locked in position before starting machine.

4. Push the safety lock forward, unlocking the switch levers.

5. With the safety lock forward, squeeze one or both of the switch levers, turning the machine on. (These levers can be operated independently of each other). The safety lock will not re-engage until both levers are released.

6. To stop the machine, release the switch levers.

7. Do not let machine rest on pad. When finished with the machine, return handle to the storage position.

NOTE: The machine is equipped with a circuit breaker to protect the motor in the event an overload condition occurs. The circuit breaker is located on the handle. Push the reset button to restart the machine. If the breaker trips again, correct the cause of overloading before proceeding.

OPERATION

DAILY MAINTENANCE

1. Inspect power cord for wear. To prevent electrical shock replace cords with frayed or cracked insulation immediately.

2. Place machine in the storage position.

3. Check pad condition. Change if soiled or torn.

PAD INSTALLATION

1.

Lay machine back, exposing the under side.

Ensure pad is centered on pad driver. Pull pad to edge of pad driver in several directions to check for proper engagement.

NOTE: Use care when replacing center lock to

prevent cross threading.

86309580 FLOOR POLISHER 10/08/08

3-4

NOTES:

3-5

86309580 FLOOR POLISHER 10/08/08

SCRUB BRUSHES

NOTE: All original equipment brushes are equipped with “Perform Alert

©

”. This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert

©

” brushes have pre-trimmed bright yellow tufts to indicate the length of a worn out brush. When the tufts in the scrub brush wear to a length equal to the yellow tufts, the scrub brushes should be replaced.

There are five different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market and further add to the flexibility of the machine.

Please refer to the following to assist in selecting the proper brush or pad for the work at hand.

UNCOATED FLOORS

Aggressive Grit

is a nylon fiber impregnated with silicone carbide grit. It grinds away stain, soil, and removes surface material.

Mild Grit

is a less aggressive silicone carbide grit suitable for cleaning medium soil conditions.

Advantages are faster ground speed than nylon bristles on light solid applications.

Nylon

is a general-purpose scrub brush with stiff bristles. Polypropylene works well for maintaining concrete, wood and tile floors.

SERVICE SCHEDULE

Check pad wear to prevent buildup of chemicals

Check pad driver system for damage

Check handles, switches, and knobs for damage

Store with pad off the floor

Check all bearings for noise

Check skirt/bumpers for damage and replace as necessary

Check overall performance of machine

MAINTENANCE

FINISHED FLOORS

Nylon Polish

is the softest brush. It will gently clean finished tile or terrazzo floors without removing floor finish or floor material. Used for washing highly polished or burnished floors.

Nylon

bristles are used in a variety of applications on coated or uncoated surfaces.

White Pads

(Polishing) are used for dry polishing to achieve a high-gloss appearance, or surface washing on highly polished or burnished floors.

Red Pads

(Buffing) are used for light-duty scrubbing. When used with a mild detergent they will provide surface cleaning without removing the finish.

Blue Pads

(Scrubbing) are used for heavy-duty scrubbing and light stripping. The blue pads remove less finish than brown stripping pads, yet will remove black marks, stains and dirt.

Brown Pads

(Stripping) are used for easy and complete removal of old floor waxes/finishes.

They will quickly remove ground in dirt, black heel marks, and spills. When used with the proper stripper, this pad leaves the floor clean and ready for finishing.

The scrub brushes should be checked before each days work for wire, string, wear and damage. The scrub brushes should be replaced if brush bristles are missing or if yellow Perform Alert

©

indicates minimum brush length.

*

*

*

*

*

*

*

86309580 FLOOR POLISHER 10/08/08

4-1

MACHINE TROUBLESHOOTING

PROBLEM CAUSE

Machine will not run Circuit breaker tripped in building.

Power switch failure

Tripped circuit breaker

Faulty power cord

Fuse in motor blown

(Dual speed only)

Electrical shock

Repeated circuit breaker tripping

Excessive vibration

Equipment not grounded

Receptacle not grounded

Internal wiring problem

Mechanical problem

Faulty circuit breaker

Pad not centered

Damaged or unevenly worn pad

Pad does not turn but motor is running

Damaged pad driver

Sheer coupling has failed

SOLUTION

Check and reset.

Test switch for continuity and replace if necessary.

Reset.

Replace.

Replace

CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse holder. Fuse will only open under extreme conditions.

Investigate cause before replacing.

Follow grounding instructions exactly.

Have an electrician inspects building’s wiring.

Ensure that the machine wiring matches the appropriate wiring diagram. Replace any wires or components that are short circuiting.

Higher amp draws indicate a mechanical problem. Find the problem before using the machine.

Test circuit for continuity.

Replace circuit breaker if necessary.

Re-center pad.

Replace pad. Do not rest machine on pad when not in use.

Replace.

Replace coupling.

4-2

86309580 FLOOR POLISHER 10/08/08

NOTES:

86309580 FLOOR POLISHER 10/08/08

4-3

BRUSH/PAD DRIVER

3

3

2A-2W

5-1

86309580 FLOOR POLISHER 10/08/08

REF PART NO. PRV NO. QTY DESCRIPTION

1A 86284280 02216

1B 86284330 02396

- PAD DRIVER, 13" POLISHER

- PAD DRIVER, 15" POLISHER

1C

1D

1E

2A

86000120

86284290

86284300

86283720

02218

02217

02219

02232

2B 86283730 02233

- PAD DRIVER, 17" POLISHER

- PAD DRIVER, 19” HS

- PAD DRIVER, 20" POLISHER

- BRUSH, 13" NYL.POL. W/CLT.PLT

-

BRUSH, 13" NYL.SCRUB

W/CLT.PLT

2C 86283740 02234

2D

86283750

- BRUSH, 13" MILD GRIT W/CLT.PLT

BRUSH, 13" AGG. GRIT

02235 -

W/CLT.PLT

2E 86283760 02236

2F 86230480 02447

-

-

BRUSH, 13" POLYPRO W/CLT. PLT

BRUSH, 15” NYL.POL. W/CLT.PLT

2G 86230490 02448

2H

2J

86230460

86230450

02445

02444

-

BRUSH, 15” NYL. SCRUB

W/CLT.PLT

- BRUSH, 15” MILD GRIT W/CLT.PLT

- BRUSH, 15” AGG.GRIT W/CLT.PLT

2K

2L

86230470

86000140

02446

02242

2M 86283800 02240

- BRUSH, 15” PLOYPRO W/CLT.PLT

- BRUSH, 17" NYL. POL. W/CLT.PLT

-

BRUSH, 17" NYL.SCRUB

W/CLT.PLT

2N 86000130 02241 - BRUSH, 17" MILD GRIT W/CLT.PLT

2P 86283710 02205 - BRUSH, AGG. MALGRIT W/C.P

2Q 86000110 02206 - BRUSH, 17" POLYPRO W/CLT. PLT

2R 86283790 02239

2T 86283770 02237

-

-

BRUSH, 20"

NYL.POL.W/CLT.PLT.SFT

BRUSH, 20” NYL.SCRUB

W/CLT.PLT

2U 86283780 02238

2V 86283690 02202

- BRUSH, 20" MILD GRIT W/CLT.PLT

-

BRUSH, 20" AGG. MALGRIT

W/C.P.

2W 86283700 02203 - BRUSH, 18" POLYPRO W/CLT. PLT

3 86284350 02220 - PLATE, PAD CLUTCH

BRUSH/PAD DRIVER

SERIAL NO.

FROM

NOTES:

86309580 FLOOR POLISHER 10/08/08

5-2

ELECTRICAL-120V

6

9

8

7

11

5

10

2

14 A-C

1

3

13

12

4

5-3

86309580 FLOOR POLISHER 10/08/08

ELECTRICAL-120V

REF PART NO. PRV NO. QTY DESCRIPTION

1 86002010 14942 1 BOOT, 3/8 CIRCUIT BREAKER

2 86198450 20005 1 CLAMP, 5/16 NYLON

4 86216920 23206 1 CORDSET, 14/3 X 52 IN, SJT, BLK

5 86268450 70689 1 SCR, M4.8 X 10 HHTF TYPE B

6 86136780 70801 2 SCR, M3.5 X 40 PHTF

7 86007110 72123 2 SWITCH, 25A SPST 125-250V SNAP

8 86224750 73993 1 SPRING, COMP, .48OD X .91

9 86137290 87057 2 WASHER, M4 LOCK

10 86137330 87208 1 WASHER, M5 LOCK

11 86215140 140674 1 BARRIER SHEET

12 86224930 730012 1 STRAIN RELIEF, 14/3 STRAIGHT

13 86224300 730021 1 SPACER, POLISHER HANDLE

SERIAL NO.

FROM

14A 86291460

14B 86312500

-

-

-

1

1

1

BREAKER, 11A VDE CIRCUIT

BREAKER, CIRCUIT, 13A VDE

BREAKER, 14A, VDE CIRCUIT

NOTES

SP13, SP15, SP17,

U17, SPT17, SP20,

U20

SP17X, U17X,

SPT20X, SP20X,

U20X

SPDS20, UDS20 14C 86312460

86309580 FLOOR POLISHER 10/08/08

5-4

ELECTRICAL-230V

6

9

8

7

11

5

10

2

14 A-C

1

3 A-B

13

12

4

5-5

86309580 FLOOR POLISHER 10/08/08

ELECTRICAL-230V

REF PART NO. PRV NO. QTY

1 86002010 14942

2 86198450 20005

1

1

DESCRIPTION

BOOT, 3/8 CIRCUIT BREAKER

CLAMP, 5/16 NYLON

3A 86216950 23212

CORD SET, EURO 1.5MM X 75

BLK

3B 86216970 23217 CORD SET, SAA33 1.5MM X 75

4

5

8

9

10

11

12

13

86216920

86268450

6 86136780 70801

7 86007110 72123

86224750

86137290

86137330

86215140

86224930

86224300

23206

70689

73993

87057

87208

140674

730012

730021

1 CORDSET, 14/3 X 52 IN, SJT, BLK

1 SCR, M4.8 X 10 HHTF TYPE B

2 SCR, M3.5 X 40 PHTF

2 SWITCH, 25A SPST 125-250V

1 SPRING, COMP, .48OD X .91

2 WASHER, M4 LOCK

1 WASHER, M5 LOCK

1 BARRIER SHEET

1 STRAIN RELIEF, 14/3 STRAIGHT

1 SPACER, POLISHER HANDLE

14A 86312470 - 1 BREAKER, 3A, VDE CIRCUIT

14B 86215710 141046 1 BREAKER, 5A VDE CIRCUIT

14C 86312530 - 1 BREAKER, CIRCUIT 10A, VDE

SERIAL NO.

FROM

NOTES

SP17HDIE,

SP17IE, SPX17IE,

SPDS17IE

SP17IA, SP17XIA,

SPDS17IA

SP17IA, SP17IE

SP17HDIE,

SP17XIA, SP17XIE

SPDS17IA,

SPDS17IE

86309580 FLOOR POLISHER 10/08/08

5-6

DECK

5-7

9A-9F

2A-2D

10

1

4

12

13

6

11

7

5

3

14 8

86309580 FLOOR POLISHER 10/08/08/08

REF PART NO. PRV NO. QTY

1 86214930

2A 86216350

2B 86216330

03111

14373

14371

DESCRIPTION

1 AXLE, MAIN POLISHER

1 BUMPER, EXTRUSION 53.4 IN.

BUMPER, EXTRUSION 37.3”

2C 86216340 14372 - BUMPER, EXTRUSION 43.8"

2D 86216350 14373

3 86216600 27871

4 86221860 51328

5 86271550 57220

6 86222270 57276

7 86133340 70262

8 86276570 70691

9A 86288430 29211

9B 86288440 29212

- BUMPER, EXTRUSION 53.4"

2 CAP, EXTRUSION

2 LINK, HANDLE ADJUST

2 NUT, M6 X 1 NYLOCK

2 NUT, PUSH FLAT RD .51 ID

2 SCR, M8-1.25 X 20 HHMS PLTD

2 SCR, M6 X 25 HHCS

1 DECK, 13 IN POLISHER, BLUE

1 DECK, 15 IN POLISHER, BLUE

9C 86217600 29213 1 DECK, 17 IN POLISHER, BLUE

9D 86288960 29213GRY 1 DECK, 17 IN POLISHER, GRAY

9E 86217620 29214BLU 1 DECK, 20 IN POLISHER BLUE

9F 86288970 29214GRY 1 DECK, 20 IN POLISHER, GRAY

10 86288740 70709 1

11 86137280 87054 2 WASHER, M8 FLAT DIN125A PLT

12 86226020 89206

13 86225720 87203

14 86137340 87211

2

2

2

WHEEL, 5D X 1.25 X 13MMID GRY

WASHER, 14MMID X 36MMOD

WASHER, M6 FLAT BLK

DECK

SERIAL NO.

FROM

NOTES

SP13

SP15

U17, U17X, SPT17,

SP17, SP17X,

SP17HDIE, SP17IA,

SP17IE, SP17XIA,

SP17XIE, SPDS17IA,

SPDS17IE

U20,U20X, UDS20,

SPT20X,SP20,SP20X,

SPDS20

SP13

SP15

SPT17, SP17, SP17X,

SP17HDIE, SP17IA,

SP17IE, SP17XIA,

SP17XIE, SPDS17IA,

SPDS17IE

U17,U17X

SPT20X,SP20,SP20X,

U20,U20X, UDS20

86309580 FLOOR POLISHER 10/08/08

5-8

HANDLE

5

11

18

23

12

13

1

9

10

21

24

20

8

27

6

16

2

14

19

22

14

25

15

20

20

8

4

23

18

11

17

26

7

3

5-9

86309580 FLOOR POLISHER 10/08/08

REF PART NO. PRV NO. QTY

1 86215130 14344

2 86216370 14434

3 86004070 36196

1

DESCRIPTION

BAR, HANDLE ADJUST

1 BUMPER, BURNISHER HANDLE

2 GRIP, POLISHER HANDLE

4 86218440 38290 1 HANDLE,

5 86005150 51326 1 LOCK, SAFETY HANDLE

6 86005160 51327

7 86136350

13 86136680

14 86288450

15 86136720

57274

8 86136360 57275

9 86222560 66334

10 86223550 67430

11 86274230 70135

12 86136670 70686

70687

70689

70701

2 LEVER,

4

2

1

NUT, M6 HEX FINISH

NUT, M10 X 1.5 HEX NYLOK PLTD

1 PIN, PIVOT, HANDLE ADJUST

1 ROD, HANDLE ADJUST

2 SCR, M8 X 30 HHMS

2 SCR, M6 X 45 SHCS, BLK

2 SCR, M6 X 50 SHCS, BLK

3 SCR, M4.8 X 10 HHTF TYPE B

SCR, M10 X 1.50 X 90 HHCS PLTD

16 86224740 73990

17 86225370 78437

18 86137280 87054

19 86279080 87058

2 SPRING, EXT, .50D X 3.5L

1 TUBE, GRIP HANDLE

2 WASHER, M8 FLAT DIN15A PLT

2 WASHER, M4 FLAT DIN125A PLT

20 86010720 87086

21 86225710 87202

22 86137330 87208

3 WASHER, M10 X 30 PLTD

1 WASHER,

1 WASHER, M5 LOCK SHAKEPROOF PLTD

23 86224290 730008 2 SPACER,

24 86310950 -

SERIAL NO.

FROM

25 86311800

26 86311810

27 86311820

-

-

-

1

1

1

TUBE ASSY, HANDLE ADJ.

HOUSING, POLSHR HANDLE RR, CB

HOUSING, POLSHR HANDLE FRT,CB

HANDLE

NOTES

86309580 FLOOR POLISHER 10/08/08

5-10

MOTOR

9

8 A-B

7

6

DUAL SPEED ONLY

1 A-D

7

6

2

5

4

3

5-11

86309580 FLOOR POLISHER 10/08/08

MOTOR

REF PART NO. PRV NO. QTY

1A 86312270

1B 86312280

1C 86312300

1D 86312310

2 86217490 27884

3

4

5

6

7

9

86223690

86136710

86279090

86223700

86223030

8A 86312290

8B 86312320

86217500

-

-

-

-

70702

70698

87067

70723

62917

-

-

27892

1

1

1

1

1 COVER,

3 SCR, M5 X .8 X 15MM BLK

4 SCR, 5/16-18 X 3/4 HHCS GR5 BLK

4 WASHER, 5/16 LOCK INT STAR PLT

6 SCR, M5 X .8 X 15MM SHCS BLK

1 PLATE, ADAPTER POLISHER MOTOR

1

1

1

DESCRIPTION

MOTOR, 1HP 115V INDUCTION

MOTOR, 1.5HP 115V INDUCTION

MOTOR, 1HP 230V INDUCTION

MOTOR, 1.5 HP 230V INDUCTION

MOTOR, 115V, 1.75HP 175/300RPM

MOTOR, 230V, 1.75HP 175/300RPM

COVER ASM, MOTOR

SERIAL NO.

FROM

NOTES

SP13, SP15,

SP17, U17,

SPT17, SP20,

U20

SP17X, U17X,

SPT20X,

SP20X, U20X

SP17IA,

SP17IE

SP17HDIE,

SP17XIA,

SP17XIE

SP13, SP15,

SP17, U17,

SPT17, SP20,

U20, SP17X,

U17X, SPT20X,

SP20X, U20X,

SP17IA,

SP17IE,

SP17HDIE,

SP17XIA,

SP17XIE

SPDS20,

UDS20

SPDS17IA,

SPDS17IE

SPDS20,

UDS20,

SPDS17IA,

SPDS17IE,

SP17IA,

SP17IE

86309580 FLOOR POLISHER 10/08/08

5-12

WIRING-120V

CORD SET

120V AC 15A

WHT

GRN

BLK

-CB1

-SWITCH

1

-SWITCH

WHT

BLK

GRN

REF PART NO. PRV NO. QTY

1 86311830 -

DESCRIPTION

1

WIRE, 125MM, BLK/14,

76029X76029

WHT

BLK

-MOTOR

GRN

M

SERIAL NO.

FROM

NOTES:

5-13

86309580 FLOOR POLISHER 10/08/08

WIRING –230V

CORD SET

120V AC 15A

WHT

GRN

BLK

-CB1

-SWITCH

1

EMC FILTER

-SWITCH

EMC FILTER2

WHT

BLK

GRN

REF PART NO. PRV NO.

1 86311830 -

QTY DESCRIPTION

1

WIRE, 125MM, BLK/14,

76029X76029

WHT

BLK

-MOTOR

GRN

M

SERIAL NO.

FROM

NOTES:

86309580 FLOOR POLISHER 10/08/08

5-14

SUGGESTED SPARE PARTS

PART NO.

86224740

86224750

86007110

86215130

86222560

86223550

PRV NO.

73990

73993

72123

14344

66334

67430

-

SPRING, EXT .5 OD X 3.5L

SPRING, COMP .48 OD X .91 L

SWITCH. 25A SPST 125-250V SNAP

BAR, HANDLE ADJ

PIN, PIVOT, HANDLE ADJ

ROD, HANDLE ADJ

86003660 34378 FUSE

86135540 27352

86223390

86291460

67488

PLSHER

RECTIFIER, 50A 600V BRIDGE

BREAKER, 11A VDE CIRCUIT

86312500

86312530

- BREAKER, CIRCUIT, 13A VDE

86312460

86312470

-

-

BREAKER, 14A, VDE CIRCUIT

BREAKER, 3A, VDE CIRCUIT

86215710 141046 BREAKER, 5A VDE CIRCUIT

- BREAKER, CIRCUIT 10A, VDE

SERIAL NO.

FROM

NOTES:

SP13,SP15,SP17,SP17X,

SP20, SP20X, SPDS20,

UDS20

SP13,15,17,17X,20,20X,

SPDS20, UDS20

SPDS20, UDS20

SPDS20, UDS20

SP13, SP15, SP17, U17,

SPT17, SP20, U20

SP17X, U17X, SPT20X,

SP20X, U20X

SP17IA, SP17IE

SP17HDIE, SP17XIA,

SP17XIE

SPDS17IA, SPDS17IE

5-15

86309580 FLOOR POLISHER 10/08/08

86309580 FLOOR POLISHER