Graco 313384B GTX 2000EX Owner's Manual

Operation
GTX™ 2000EX
313384B
- For Water-Based Materials Only -
Model 257030
Sprayer with Graco Trigger Gun
120 psi (8.27 bar) Maximum Working Air Pressure
120 psi (8.27 bar) Maximum Working Fluid Pressure
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Related Manuals:
Pump 308479
Gun
310616
Repair 313385
ti13066a
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and
cause serious injury.
• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
2
313384B
PLASTIC PARTS CLEANING SOLVENT HAZARD
Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many
solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property
damage. See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent
manufacturer’s warnings.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eye wear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
• Gloves
• Hearing protection
NOTICE
Water or material remaining in unit when temperatures are below freezing can damage pump and/or delay startup.
To insure water and material are completely drained out of unit:
1. Remove material line from sprayer.
2. Tip sprayer to allow material (water) to flow out of pump inlet.
Before adding material or starting unit in cold weather, run warm water through pump.
313384B
3
Component Identification
Component Identification
A
B
D
C
K
ti13066a
E
F
H
G
J
L
4
313384B
Component Identification List
Component Identification List
A
Nozzle Storage
B
Hopper
C
Hopper Quick Connect
D
Diaphragm Pump
E
Material Outlet Option 1
F
Material Outlet Option 2
G
Gun Air Outlet Quick Connect
H
Material (Pump) Air Pressure Gauge and Control Knob
J
Gun Air Pressure Gauge and Control Knob
K
Gun (see manual 308878)*
L
Air Compressor (not supplied by Graco)
* Reference numbers used in gun illustrations reflect numbers shown in gun manual 308878.
313384B
5
Pressure Relief Procedure
Pressure Relief Procedure
To reduce the risk of injury, follow this Pressure Relief
Procedure whenever you:
• Are instructed to relieve pressure
• Stop spraying
• Service equipment
• Install or clean spray nozzle
• Disconnect or connect hose
23
1. Turn OFF air inlet valve (E).
TI
3. Trigger gun. Spray material back into hopper (G).
E
2. Open gun air valve (23).
6
G
313384B
Setup
Setup
Preparation
Removing and Installing Hopper
1. Connect air and material hoses to gun. Tighten
securely.
Hopper (G) can be removed from cart for cleaning and
when using Siphon Kit 248112 (available from Graco
distributor).
Removing Hopper (G)
1. Push down 2 latches on each side of hopper coupler (H).
23
ti3899a
ti4003a
2. Connect one end of material hose (cc) to material
outlet (K or L) and other end to gun material inlet
(bb).
2. Lift hopper (G) straight up off of unit.
NOTE: Material plug must be installed in material
outlet (K or L) you are not using.
K
L
cc
ti3778b
dd
N
ti3900a
3. Open gun air valve (23).
313384B
7
Setup
Installing Hopper (G)
Additional Equipment Needed
1. Position coupler (H) over material outlet and slide
hopper (G) straight down, over fitting as far as it will
go. Make sure hopper bracket is positioned over cart
handle rod.
Auxiliary Air Compressor (not supplied)
Minimum Requirements:
•
12 CFM @ 100 psi (maximum 120 psi)
•
3/8 in. x 25 ft. minimum airline rated at 120 psi
ti3925a
2. Secure latches on each side by pushing them firmly
up into locked position.
ti3902a
8
313384B
Wetting Hose
Wetting Hose
4. Trigger gun into waste pail until hopper no longer
contains water.
Wet inside of hose before each use to flush out sediment and prevent texture material from packing out
hose.
1. Pour one (1) gallon (3.8 liters) of clean water into
hopper.
ti4290a
WASTE
5. Open gun air valve (23) to relieve compressor air.
2. Close gun air valve (23).
23
23
TI
closed
ti4005
3. Turn air inlet valve (E) open. Aim gun into hopper
(G) and trigger gun to circulate water for a few minutes to wet inside of material hose.
313384B
9
Wetting System
Wetting System
1. Fill hopper (G) with prepared textured material.
G
NOTE: If spraying a simulated acoustic and course
aggregate material, disconnect hose at gun, prime
pump and hose and circulate material back into
hopper for 10 seconds. Turn off pump. Install gun
and tip.
4. Inspect hose for kinks which could restrict fluid flow.
5. Trigger gun into a pail. When texture material
appears at tip, move gun to hopper and circulate
until material flows in a solid stream. See System
Adjustment (page 14) for proper spray pattern and
pump and gun adjustments.
ti3905a
NOTICE
Do not mix material in hopper. Mixing material in hopper
can damage hopper, result in an inconsistent mix and
packout can occur.
2. Install tip (see Nozzle Selection Chart, page 13).
3. Open gun air valve (23) to relieve air pressure.
ti4290a
WASTE
6. Adjust gun air pressure (U) and pump air pressure
(T) on sprayer to achieve desired result.
23
U
TI
NOTICE
Do not allow material to flow out of gun when air valve
(23) is closed or material packout in needle can occur.
10
T
313384B
Mixing Material
Mixing Material
NOTICE
Do not use any solvent-based materials. Use
water-based materials only. Proper material mixture is
essential. Pump will not operate if material is too thick.
NOTE: For best results, mix material in a separate
container and pour it into hopper.
3. After texture is thoroughly mixed, gently set ball end
of Material Thickness gauge on surface of mixture.
NOTE: For accurate test, be sure gauge is completely dry and clean before each use.
4. Observe ball on material. When material is thin
enough to spray, ball will sink completely into mixture.
1. Slowly add one bag of texture to clean water as
instructed on bag. For best results, do not use partial bags.
ti3906a
WATER
2. Agitate to a smooth, lump-free consistency.
5. If ball does not sink completely into mixture within
10 seconds add more water, agitate again and
repeat test.
NOTE: Thicker materials that do not pass Material
Thickness Gauge test can still be used. Before
spraying thicker materials, test pump performance
first. If material is too thick, pump will perform
poorly.
ti3907a
313384B
11
Operation Characteristics
Operation Characteristics
•
Always start system with compressor air relieved. See
Pressure Relief Procedure, page 6.
•
Always have material outlet plug installed in opening
(K or L) not in use when material is in hopper. If plug
is removed, hopper will drain out.
•
Always have material hose installed in opening (K or
L) when material is in hopper. If hose is removed,
hopper will drain out through pump.
K
L
Gun air pressure is regulated using air pressure
control on sprayer (U) as well as gun air valve
located on gun handle (23). Site gauge on sprayer
allows duplication of air pressure setting. Gun air
valve (23) allows for additional air pressure adjustment.
23
closed
ti4005a
ti3787b
•
Air pressure is controlled with pressure control knob
(J) and displayed on gauge.
H
J
12
313384B
Spray Techniques
Spray Techniques
Nozzle Selection
NOTICE
Keep pump and hose clean when switching between simulated
acoustic, knockdown, and orange peel applications. A dirty
pump can release particles of texture into the finish.
Application
Nozzle Orifice†
Nozzle Number
Air Volume‡
Fog
1/8 in.
3
High
3/16 in. (fine)
4
Simulated Acoustic 1/4 in. (fine to medium)
6
Medium to High
5/16 in. (coarse)
8
Orange Peel
1/8 to 3/16 in.
3-4
Medium to High
Splatter Coat
1/4 to 5/16 in.
6-8
Low to Medium
Knock-Down
5-16 in.
8
Low
† Control air volume with gun air flow valve (31).
‡ For more material volume, use tip with larger orifice.
313384B
13
System Adjustment
System Adjustment
NOTE: Keep a small amount of air flowing through
air line and gun tip to prevent material from backing
up needle.
1. Open gun air valve (23).
4. To select correct nozzle for your applications, consider size of aggregate in material and coarseness
of spray pattern. Remember the larger the nozzle,
the larger the spray pattern. See Nozzle Selection,
page 13.
NOTE: More air produces a finer finish; less air produces a coarse finish.
23
5. When adjusting flow adjustment nut (b), release trigger (C), then adjust.
TI
2. Test spray pattern on cardboard. Hold gun 18 to 30
in. (45 to 75 cm) from surface. Use this spray distance for most applications. Overlap each stroke
50% in a circular motion.
B
C
ti4338a
If adjusting while triggered, needle will turn but provide
no adjustment.
If flow adjustment nut will not turn, check to see if it is:
ti4004a
3. Adjust gun air valve (23) to achieve uniform, round
spray pattern. It may be necessary to change spray
nozzle to achieve desired spray pattern.
•
Set to maximum adjustment, or
•
If there is material on threads. Clean threads as
needed.
6. Check material consistency often. Material may
thicken as it sits and slow down production or affect
spray pattern. Thin with mater as needed to maintain proper consistency.
23
ti3999a
14
313384B
System Adjustment
Material Flow Adjustment
B
NOTE: Keep a small amount of air flowing through
air line and gun tip to prevent material from backing
up needle.
Preventing Material Surge at
Gun Trigger
Pressure will build up in system when not triggering gun.
To prevent material surge at beginning of spray pattern:
•
Point gun away from surface to be sprayed when
trigger is first pulled.
•
Hold gun away from surface and gradually bring gun
to surface.
•
Trigger gun as little as possible.
ti4339a
•
For a lighter spray pattern, decrease material pressure at sprayer.
•
For a heavier spray pattern, increase material pressure at sprayer.
For Continuous Spraying
Air Flow Adjustment
23
D
TI
•
Trigger gun.
•
To decrease air flow, close air valve (23) clockwise.
•
To increase air flow, open air valve (23) counter-clockwise.
ti4006a
•
313384B
Engage trigger lock (D) to hold trigger open and
reduce fatigue.
15
Shutdown and Cleanup
Shutdown and Cleanup
•
NOTICE
Turn off sprayer if you are going to stop spraying for 5 minutes or longer.
•
Before removing material hose, Relieve Pressure and make sure there is no material inside of hose.
•
To keep sprayer in good operating condition, always clean it thoroughly and prepare it properly for storage.
•
If water freezes in sprayer, damage may occur. During cold weather, store sprayer where it will not freeze.
Spray water into waste bucket to empty material hopper.
NOTE: A soft brush can be used to loosen dried-on
material.
After Spraying
1. Relieve Pressure, page 6.
4. Follow Pressure Relief, page 6.
2. Fill material hopper with 2 - 4 gallons of clean water.
3. Spray inside material hopper to circulate water
through gun and hose. While circulating water, use
gun to clean material hopper.
16
313384B
Maintenance
Maintenance
Component
Hoses
Air and Material Hose Connections
Diaphragm Pump
Task
Frequency
Check for wear and/or damage
Daily
Drain system of all water
After each use
Add a few drops of light oil
After each use
Lubricate
Remove hose from pump air line and
add 2 drops of machine oil to air inlet
after every 500 hours of operation (or
monthly)
Flush
Before storing
Thread connections
Gun
Before each use, check to make sure
all connections are light and leak-free
Torque all threaded connections
every two months
Clean
After each use
Add a few drops of light oil to flow
adjustment
After each use
Technical Data
Maximum working air pressure
Maximum working fluid pressure
Compressor (not supplied by Graco)
Air Delivery
Hopper capacity
Maximum delivery with texture material
Dimensions
Length
Width
Height
Sound
Weight
With hoses and gun
Wetted Parts
313384B
120 psi (8.27 bar)
120 psi (8.27 bar)
Oil-less compressor
12 CFM @ 100 psi minimum (340 lpm @ 6.9 bar)
17 US gallons (64 liters)
4.0 gpm (15.14 lpm)
38 in. (965 mm) with handles
24 in. (610 mm)
40 in. (1016 mm)
Reference Pump Manual 308479
110 lb (49.9 kg)
PVC, zinc plate CS, Buna-N, aluminum, brass,
polyethylene, SST, UHMW, Delrin
17
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 313384
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2008, Graco Inc. is registered to I.S. EN ISO 9001
www.graco.com
10/2008