SM003 32PD3000E 42PD3000E SERVICE MANUAL

SM003

42PD3000E

SERVICE MANUAL

MANUEL D'ENTRETIEN

WARTUNGSHANDBUCH

CAUTION:

Before servicing this chassis, it is important that the service technician read the “Safety

Precautions” and “Product Safety Notices” in this service manual.

Data contained within this Service manual is subject to alteration for improvement.

ATTENTION:

Avant d’effectuer l’entretien du châassis, le technicien doit lire les «Précautions de sécurité» et les «Notices de sécurité du produit» présentés dans le présent manuel.

Les données fournies dans le présent manuel d’entretien peuvent faire l’objet de modifications en vue de perfectionner le produit.

VORSICHT:

Vor Öffnen des Gehäuses hat der Service-Ingenieur die „Sicherheitshinweise“ und „Hinweise zur Produktsicherheit“ in diesem Wartungshandbuch zu lesen.

Die in diesem Wartungshandbuch enthaltenen Spezifikationen können sich zwecks Verbesserungen ändern.

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

Plasma TV

October 2002

32PD3000 / 42PD3000

Safety

ENGLISH

SAFETY PRECAUTIONS

WARNING: The following precautions must be

observed.

ALL PRODUCTS

Before any service is performed on the chassis an isolation transformer should be inserted between the power line and the product.

1. When replacing the chassis in the cabinet, ensure all the protective devices are put back in place.

2. When service is required, observe the original lead dressing. Extra precaution should be taken to ensure correct lead dressing in any high voltage circuitry area.

3. Many electrical and mechanical parts in

HITACHI products have special safety related characteristics. These characteristics are often not evident from visual inspection, nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified by marking with a ! on the schematics and the replacement parts list. The use of a substitute replacement component that does not have the same safety characteristics as the

HITACHI recommended replacement one, shown in the parts list, may create electrical shock, fire, Xradiation, or other hazards.

4. Always replace original spacers and maintain lead lengths. Furthermore, where a short circuit has occurred, replace those components that indicate evidence of overheating.

5. Insulation resistance should not be less than 2M ohms at 500V DC between the main poles and any accessible metal parts.

6. No flashover or breakdown should occur during the dielectric strength test, applying 3kV AC or

4.25kV DC for two seconds between the main poles and accessible metal parts.

7. Before returning a serviced product to the customer, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock. The service technician must make sure that no protective device built into the instrument by the manufacturer has become defective, or inadvertently damaged during servicing.

CE MARK

1. HITACHI products may contain the CE mark on the rating plate indicating that the product contains parts that have been specifically approved to provide electromagnetic compatibility to designated levels.

2. When replacing any part in this product, please use only the correct part itemised in the parts list to ensure this standard is maintained, and take care to replace lead dressing to its original state, as this can have a bearing on the electromagnetic radiation/immunity.

PICTURE TUBE

1. The line output stage can develop voltages in excess of 25kV; if the E.H.T. cap is required to be removed, discharge the anode to chassis via a high value resistor, prior to its removal from the picture tube.

2. High voltage should always be kept at the rated value of the chassis and no higher. Operating at higher voltages may cause a failure of the picture tube or high voltage supply, and also, under certain circumstances could produce X-radiation levels moderately in excess of design levels. The high voltage must not, under any circumstances, exceed

29kV on the chassis (except for projection

Televisions).

3. The primary source of X-radiation in the product is the picture tube. The picture tube utilised for the above mentioned function in this chassis is specially constructed to limit X-radiation. For continued X-radiation protection, replace tube with the same type as the original HITACHI approved type

4. Keep the picture tube away from the body while handling. Do not install, remove, or handle the picture tube in any manner unless shatterproof goggles are worn. People not so equipped should be kept away while picture tubes are handled

LASERS

If the product contains a laser avoid direct exposure to the beam when the cover is open or when interlocks are defeated or have failed.

1

32PD3000 / 42PD3000

FRANÇAIS

CONSIGNES DE SECURITE

AVERTISSEMENT: vous devez respecter les

précautions suivantes

POUR TOUS LES PRODUITS

Avant d’effectuer une intervention d’entretien sur le châssis, vous devez insérer un transformateur d’isolement entre la ligne d’alimentation électrique et le produit.

1. Lors de la remontage du châssis dans le coffret, vérifiez que tous les dispositifs de protection sont remis en place.

2. Lorsqu’une intervention d’entretien s’avère nécessaire, respectez l’agencement d’origine des conducteurs. Vous devez prendre des precautions supplémentaires pour garantir un agencement correct des conducteurs dans toutes les zones où des circuits haute tension sont présents.

3. De nombreux composants électriques et mécaniques des appareils HITACHI ont des caractéristiques spéciales de sécurité. Bien souvent, ces caractéristiques ne sont pas

évidentes lors d’un examen visuel et la protection qu’ils offrent n’est pas forcément garantie si vous utilisez des composants de rechange conçus, par exemple, pour une tension plus élevée, une puissance plus forte. Les pièces de rechange qui offrent des caractéristiques spéciales de sécurité sont identifiées par un repérage comportant le symbole ! sur les schémas et sur la nomenclature des pièces de rechange. L’emploi d’un composant de rechange qui ne respecte pas les mêmes caractéristiques de sécurité que la pièce de rechange que recommande HITACHI et qui figure dans la nomenclature risque de provoquer un choc

électrique, un incendie, des rayons X ou d’autres dangers.

4. Remettez toujours en place les entretoises d’origine et respectez la longueur des conduites.

En outre, à la suite d’un court-circuit, remplacez les composants présentant des signes de surchauffe.

5. La résistance d’isolement doit être supérieure ou

égale à 2 méga ohms à 500 V c.c. entre les poles principaux et des composants métalliques accessibles, quels qu’ils soient.

6. Aucun claquage et aucune rupture ne doit se produire pendant l’essai de résistance diélectrique

à la suite de l’application d’une tension de 3 kV c.a. ou de 4,35 kV c.c. pendant deux secondes entre les poles principaux et des composants métalliques accessibles.

7. Avant de remettre au client un produit qui a fait l’objet d’un entretien, le technicien qui s’est chargé de cette intervention doit tester à fond cet ensemble pour s’assurer qu’il ne présente aucun danger opérationnel et aucun risque de choc

électrique. Ce technicien doit s’assurer qu’aucun des dispositifs de protection intégrés à cet instrument par le fabricantn’est défectueux ou n’a

été endommagé de façon accidentelle lors de l’entretien. suivantes

2

LABEL CE

1. Les produits HITACHI peuvent avoir reçu le label

CE qui figure sur la plaque signalétique pour indiquer que cet ensemble contient des composants qui ont fait l’objet d’une homologation spécifique de respect des normes de compatibilité

électromagnétique en fonction de niveaux bien spécifiés.

2. Lors du remplacement d’un des composants de ce produit, utilisez uniquement le composant correct identifié dans la nomenclature afin de maintenir le respect de cette norme ; en outre, vous devez également ramener l’agencement des conducteurs à son état d’origine car cela peut avoir une influence au niveau des rayonnements

électromagnétiques et sur la protection contre ces rayons.

PICTURE TUBE

1. L’étage de sortie des lignes peut développer des tensions de plus de 25 kV ; s’il faut retirer le chapeau de protection contre les tensions extrêmement élevées, il convient de décharger l’anode contre le châssis par le biais d’une résistance de forte valeur avant de déposer ce chapeau du tube image.

2. La haute tension doit toujours se maintenir à la valeur nominale du châssis et ne pas dépasser cette dernière. Un fonctionnement à des températures élevées peut provoquer une défaillance du tube image ou l’entrée d’une tension

élevée. Dans certains cas, cela peut même provoquer des rayons X d’un niveau légèrement supérieur aux valeurs de calcul. Cette haute tension ne doit en aucun cas dépasser 29 kV sur le châssis (à l’exception des téléviseurs de projection).

3. La principale source de rayons X de cet appareil est le tube image. Le tube image employé pour assurer la fonction susmentionnée dans ce châssis est spécialement construit pour limiter des rayons

X. Pour maintenir cette protection contre les rayons

X, il faut remplacer le tube d’origine d’un type agréé par HITACHI par un autre tube de même type.

4. Lors des manipulations, ne tenez jamais le tube image contre le corps. Pendant toutes les operations d’installation, de dépose et de manipulation de ce tube image, quelle que soit la méthode employée, vous devez toujours porter des lunettes de sécurité anti-éclatements. Les personnes qui ne portent pas ce type de lunettes doivent se tenir à l’écart du tube image lors de la manipulation de ce dernier.

RAYONS LASER

Si ce produit contient un rayon laser, évitez toute exposition directe à ce faisceau lors de l’ouverture du couvercle ou lors de l’élimination des verrouillages de sécurité ou après défaillance de ces verrouillages.

DEUTSCH

SICHERHEITSVORKEHRUNGEN

WARNUNG: Die folgenden Vorkehrungen müssen

eingehalten werden.

ALLE PRODUKTE

Bevor die Grundplatte gewartet wird, sollte ein Trenntrafo zwischen die

Netzleitung und das Produkt eingebracht werden.

1. Wenn die Grundplatte in das Gehäuse zurückgestellt wird, stellen Sie sicher, dass alle

Schutzvorrichtungen wieder an ihrem Ort sind.

2. Wenn Wartung erforderlich ist, halten Sie die originale Verdrahtungsart ein. Besondere Vorsicht ist nötig, um die korrekte Verdrahtungsart in jedem

Hochspannungsstromkreis zu gewährleisten.

3. Viele elektrische und mechanische Teile von

HITACHI Produkten haben besondere sicherheitsbezogene Eigenschaften. Diese

Eigenschaften fallen oft nicht ins Auge, aber der durch sie gewährte Schutz kann nicht unbedingt erreicht werden, wenn man Ersatzteile benutzt, die für höhere Spannung, Leistung usw. ausgelegt sind. Ersatzteile, die diese besonderen

Sicherheitsmerkmale haben, sind in den

Prinzipskizzen und Ersatzteillisten an einem ! zu erkennen. Der Gebrauch von Ersatzteilen, die nicht dieselben Sicherheitsmerkmale haben wie die empfohlenen HITACHI Ersatzteile, wie sie in der

Ersatzteilliste aufgeführt sind, kann zu elektrischem

Schlag, Feuer, Röntgenstrahlung und anderen

Gefahren führen.

4. Immer die originalen Abstandsstücke ersetzen und die Leitungslängen beibehalten. Wo ein

Kurzschluss passiert ist, die Teile ersetzen, bei denen Überhitzung nachzuweisen ist.

5. Der Isolierwert sollte bei 500 V Gleichstrom zwischen den Hauptpolen und allen zugänglichen

Metallteilen nicht unter 2M Ohm liegen.

6. Bei der Prüfung auf Durchschlagsfestigkeit sollte kein Überschlag oder Durchschlag vorkommen, wenn zwei Sekunden lang 3 kV Wechselstrom oder

4,25 kV Gleichstrom zwischen den Hauptpolen und allen zugänglichen Metallteilen angelegt wird.

7. Bevor das gewartete Produkt dem Kunden zurückgegeben wird, muss der Wartungstechniker das Gerät gründlich prüfen, um sicherzustellen, dass es betriebssicher ist ohne das Risiko eines elektrischen Schlages. Der Wartungstechniker muss sicherstellen, dass keine vom Hersteller im

Gerät eingebaute Schutzvorkehrung schadhaft geworden ist oder bei der Wartung unabsichtlich beschädigt wurde.

CE KENNZEICHEN

1. HITACHI Produkte enthalten eventuell das CE

Kennzeichen auf dem Leistungsschild, welches angibt, dass das Produkt Teile enthält, die eigens zugelassen sind, um bis zu einem spezifizierten

Niveau elektromagnetische Störfreiheit zu bewirken.

2. Wenn Sie irgendein Teil in diesem Produkt ersetzen, benutzen Sie bitte nur das korrekte Teil, das in der Ersatzteilliste aufgeführt ist, um sicherzustell en, dass dieser Standard eingehalten

32PD3000 / 42PD3000 wird, und geben Sie acht, die Verdrahtungsart in ihren ursprünglichen Zustand zurück zu versetzen, weil das einen Einfluss auf die elektromagnetische

Abstrahlung/Störsicherheit haben kann.

BILDRÖHRE

1. Die Leitungsausgangsstufe kann Spannungen von mehr als 25 kV entwickeln; wenn die

Höchstspannungskappe entfernt werden muss, entladen Sie die Anode zum Gehäuse über einen hochohmigen Widerstand, bevor Sie sie aus der

Bildröhre entfernen.

2. Hochspannung sollte immer auf den festgelegten

Wert des Gehäuses beschränkt bleiben und nicht mehr. Betrieb bei höherer Spannung kann zum

Versagen der Bildröhre oder zu hoher

Spannungszufuhr führen und kann unter

Umständen auch Röntgenstrahlung hervorbringen, die leicht über dem Konstruktionsniveau liegt. Die

Hochspannung darf auf keinen Fall 29 kV am

Gehäuse überschreiten (außer bei

Projektionsfernsehern).

3. Die Hauptquelle der Röntgenstrahlung im

Produkt ist die Bildröhre. Die Bildröhre, die für die oben erwähnte Funktion in diesem Gehäuse benutzt wird, ist eine Spezialkonstruktion zur

Begrenzung der Röntgenstrahlung. Um den Schutz vor der Röntgenstrahlung zu behalten, ersetzen Sie bitte die Röhre durch denselben Typ wie den ursprünglichen von HITACHI zugelassenen.

8. Halten Sie die Bildröhre bei der Handhabung vom Körper weg. Sie dürfen die Bildröhre nur dann installieren, entfernen oder handhaben, wenn Sie eine nicht splitternde Schutzbrille tragen. Personen ohne derartigen Schutz sollten ferngehalten werden, solange Bildröhren gehandhabt werden.

LASER

Wenn das Produkt einen Laser enthält, setzen Sie sich keinesfalls direkt dem Strahl aus, wenn die

Abdeckung geöffnet ist oder wenn die Verriegelung versagt.

3

32PD3000 / 42PD3000

4

Contents

Safety .......................................................................................................................................................1

ENGLISH ............................................................................................................................................1

FRANÇAIS..........................................................................................................................................2

DEUTSCH ...........................................................................................................................................3

Contents ...................................................................................................................................................4

Lead Free Solder ......................................................................................................................................6

Specifications...........................................................................................................................................7

General Specifications .........................................................................................................................7

Features ;..............................................................................................................................................8

Service Data .............................................................................................................................................9

Block Diagrams .....................................................................................................................................16

AVC to PDP Block Diagram .............................................................................................................16

AVC Block Diagram..........................................................................................................................17

AVC Power Block Diagram ..............................................................................................................18

Major Connectors...............................................................................................................................19

Monitor Block Diagram.....................................................................................................................20

Schematic Drawing Descriptions...........................................................................................................21

Schematic Page 1 ; Tuner / Video Chroma........................................................................................21

Schematic Page 2 ; Sound / AV3 Control..........................................................................................23

Schematic Page 3 ; Interface Board (component input, progressive sync separation, centre audio channel)..............................................................................................................................................25

Schematic Page 4 ; Power Circuit (Voltage Regulator) / Level Shifter ...........................................27

Schematic Page 5 ; Micro Controller.................................................................................................28

Schematic Page 6 ; COMB Filter / SVHS Output .............................................................................29

Schematic Page 7 ; SCART / FC-MSC Connection..........................................................................30

Schematic; AVC Power Supply.........................................................................................................32

Schematic Drawings ..............................................................................................................................33

Schematic Sheet 1 ..............................................................................................................................33

Schematic Sheet 2 ..............................................................................................................................34

Schematic Sheet 3 ..............................................................................................................................35

Schematic Sheet 4 ..............................................................................................................................36

Schematic Sheet 5 ..............................................................................................................................37

Schematic Sheet 6 ..............................................................................................................................38

Schematic Sheet 7 ..............................................................................................................................39

AV Power Schematic.........................................................................................................................40

AV Control Schematic.......................................................................................................................41

Signal / Sound Sheet 1 .......................................................................................................................42




Filter, LED, Switch & Speakers ........................................................................................................46

Circuit Boards ........................................................................................................................................47

AV Board Side A ...............................................................................................................................47

AV Board Side B ...............................................................................................................................48

AV Power Side A...............................................................................................................................49

AV Power Side B...............................................................................................................................50

Signal / Sound Board Side A .............................................................................................................51

Signal / Sound Board Side B .............................................................................................................52

Filter, LEDs, Speaker PCBs...............................................................................................................53

Troubleshooting Flow Charts ................................................................................................................54

32PD3000 / 42PD3000

AV Power - 1 .....................................................................................................................................54

AV Power - 2 .....................................................................................................................................55

AV Power - 3 .....................................................................................................................................56

AV Circuit..........................................................................................................................................57

Assembly Drawings ...............................................................................................................................58

Audio / Video.....................................................................................................................................58

Wiring for Audio / Video Components .............................................................................................59

Monitor Front View ...........................................................................................................................60

Monitor Rear View ............................................................................................................................61

32 inch Monitor Wiring A .................................................................................................................62

32 inch Monitor Wiring B..................................................................................................................63

42 inch Monitor Wiring A .................................................................................................................64

42 inch Monitor Wiring B..................................................................................................................65

24way Digital Interface Cable Connection............................................................................................66

Microprocessor Pins...............................................................................................................................67

Connections to FC4................................................................................................................................69

PCB Connectors.....................................................................................................................................72

Replacement Parts..................................................................................................................................73

Signal / Sound Board .........................................................................................................................73

Filter Board ........................................................................................................................................75

32PD3000 ..........................................................................................................................................76

42PD3000 ..........................................................................................................................................77

Questions & Answers ............................................................................................................................79

5

32PD3000 / 42PD3000

Lead Free Solder

This product uses lead free (unleaded) solder to help preserve the environment. Please read these instructions before attempting any soldering work.

Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free

solder can splatter at high temperatures (600 °C).

• Lead free solder indicator

Printed circuit board Assemblies using lead free solder shown below are engraved with an "F" following

Board Name.

• Properties of lead free solder

•

The melting point of lead free solder is 40-50 °C higher than one of leaded solder.

When servicing solder

o

Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended. o

Although servicing with leaded solder is possible, there are a few precautions that have to be taken.(Not taking these precautions may cause the solder not to harden properly and lead to consequent malfunctions.)

• Precautions when using leaded solder o

Remove all lead free solder from soldered joints when replacing components.

o

If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the lead free solder has been completely melted (do not apply the soldering iron without adding solder).

When servicing soldering iron

A soldering iron with a temperature setting capability (temperature control function)is recommended.

The melting point of lead free solder is higher than one of leaded solder. Use a soldering iron that maintains a high stable temperature (large heat capacity),and that allows temperature adjustment according to the part being serviced, to avoid poor servicing performance.

Recommended soldering iron:

Soldering iron with temperature control function (temperature range:320-450 °C)

Recommended temperature range per part:

Soldering Part

PCB with surface mount devices

Soldering iron temperature

320 °C ±30 °C

PCB without surface mount devices

Chassis, metallic shield, etc.

380 °C ±30 °C

420 °C ±30 °C

PCBs which use lead free solder

• FC4PDP board (AVC block)

• SIGNAL/SOUND board (MONITOR block)

• SP terminal L/R board, FILTER board, LED board (MONITOR block)

6

32PD3000 / 42PD3000

Specifications

General Specifications

Item Spec

32PD3000 (PDP;32PD3000E+AVC;AV3000E) 42PD3000 (PDP;42PD3000E+AVC;AV3000E)

PDP panel 32" (ALSI for mat) Plasma display panel (16:9) , resolution 852(H) x1024(V)

Display size 976(W) x 258(D) x 580(H) unit: mm

Sound output level

Speaker

Max. 10W x 2 (6 ohm)

4 x 16 cm corn type x 2

Power supply AC 220 - 240 V 50Hz

Power consumption

PDP 260W (stand-by <2W) AVC 30W, (standby <2W)

Colour system PAL/SECAM/NTSC4.43/NTSC3.58/PAL60

Sound system I/B.G.H/LL'

???

AC 220 - 240 V 50Hz

PDP 360W (stand-by <2W) AVC 30W, (standby <2W)

PAL/SECAM/NTSC4.43/NTSC3.58/PAL60

I/B.G.H/LL'

Tuning freq. 45MHz ~ 889MHz, VHF low/VHF high/Hyper/UHF

Position selection

100 (0~99) positions. Plus channel direct (C--/S-

-) and frequency direct (---.--MHz)

PC input signal

Horizontal freq. 24KHz ~ 109KHz / Vertical freq.

50Hz ~ 85Hz

Analogue RGB, input voltage 0.7Vpp/1.0Vpp selectable

AV input

H/V separate sync (TTL level) *** sound input ; common with AV3 or AV4

SCART101 (CVBS/SVHS/LR sound) - AV1

SCART102 (CVBS/RGB/LR sound) - AV2


Dimensions

45MHz ~ 889MHz, VHF low/VHF high/Hyper/UHF

100 (0~99) positions. Plus channel direct (C--/S-

-) and frequency direct (---.--MHz)

Horizontal freq. 24KHz ~ 109KHz / Vertical freq.

50Hz ~ 85Hz

Analogue RGB, input voltage 0.7Vpp/1.0Vpp selectable

H/V separate sync (TTL level) *** sound input ; common with AV3 or AV4

SCART101 (CVBS/SVHS/LR sound) - AV1



COMPONENT (YPbPr/YCbCr/LR sound) - AV4 COMPONENT (YPbPr/YCbCr/LR sound) - AV4

Front AV (CVBS/SVHS/LR sound) - FRONT

CENTRE AUDIO input

Front AV (CVBS/SVHS/LR sound) - FRONT

CENTRE AUDIO input

PDP : 974(W) x 256(D) x 578(H) including monitor stand unit: mm

PDP : 1030(W) x ??(D) x 636(H) including monitor stand unit: mm

AVC : 430(W) x 293(D) x 121(H) unit: mm AVC : 430(W) x 293(D) x 121(H) unit: mm

Weight PDP : 28.7kg (net)

AVC : 3.2kg (net)

2 x Hitachi R6P(G) * equivalent 'AA'

PDP : 40.2kg (net)

AVC : 3.2kg (net)

2 x Hitachi R6P(G) * equivalent 'AA' Remote control batteries

42" (ALSI for mat) Plasma display panel (16:9) , resolution 1024(H) x1024(V)

1233(W) x 300(D) x 713(H) unit: mm

Max. 12W x 2 (6 ohm)

7

32PD3000 / 42PD3000

Features

;

852x1024 resolution,

Created by 32" ALIS Plasma display panel

1024x1024 resolution,

Created by 37/42" ALIS Plasma display panel

Advanced progressive & 1024 interlace, Which materializes detailed picture without flicker

TruBass by SRS,

Which gives real bass sound

Thin (9cm) and light,

By separating monitor from tuner box (AVC). It is possible to hang monitor on the wall.

Swivel stand attached monitor, Which is possible to swivel at 30deg toward left and right.

3 Scarts connectors plus front AV input, Which can be connected with DVD, Set Top Box, VCR and

C amera at the same time.

1 Component input,

Which allows YPbPr and PCbCr to be received. Signal is automatically identified.

PC input connection,

Supporting various PC display format.

8

32PD3000 / 42PD3000

Service Data

Soft version issue 1 New panel 01-Nov-02 back ground CYAN means to separate data on each 32/37/42"

RED figures are new default values

1st 2nd

SVC> TUN> ADC

OPT

AGC

LIF

AFC

PC> PC1>

PC3>

SIG> FLA

MIS> RGB >

BIF

PC2>

MAX

MIN

SNR

3rd 4th 5th

GSW

BLP

COP

MBC

MCC

MXB

BGP

CCP

DCP

PSE

PST

COL> R1

G1

B1

NOM> R2

G2

B2

WAM> R3

G3

B3

GSW

WHB

HAPC

BRN

V1.A4

32" values hex

37" values hex

42" values hex functions

read read read AGC data

80 80 80 option for destination

adj adj adj

AGC adjustment

adj adj adj

AFC adjustment for all except

L'

adj adj adj AFC adjustment for L'

read read read AFC level indication

01 01 01 gamma switch

7F 7F 7F

Black Level (RGB);user brightness control for PC

7F 7F 7F Contrast (RGB)

7F 7F 7F main brightness centre

FC4

FC4

6 D07:D00

7 D15:D08

5D 5D 5D main contrast centre

6C 6C 6C brightness Max. for wide

NORMAL/REAL

FC4 7 D07:D00

00 00 00

Brightness/Gradation PDP 27&28

00 00 00 D1&D1

01

0F

01

0F

01

0F

Tracking correction power save timer

PDP

01 01 01 PC power save enable/disable FC4

27&28 D0&D0

4 D08

OK OK OK

CAUTION !! Never press OK unless proper signal is

displayed. auto signal level adjustment activates.

read read read MAX signal level on screen

read read read min. signal level on screen

read read read FC noise level indication

read read read Gain R ; warm

read read read Gain G ; warm

read read read Gain B ; warm

PDP

Read/Write

PDP

Read/Write

PDP

Read/Write

read read read Gain R ; normal

read read read Gain G ; normal

read read read Gain B ; normal

read read read Gain R ; cool

read read read Gain G ; cool

read read read Gain B ; cool

01 01 01 gamma switch

00 00 00 white balance 0;cool, 1;normal,

2;warm --- synchronizing with user operation MENU

01 01 01

Q.MODE + Heat APC

01 01 01 burn in mode

Device

PDP

PDP

Read/Write

PDP

Read/Write

PDP

Read/Write

PDP

Read/Write

PDP

Read/Write

PDP

Read/Write

PDP

PDP

PDP

13/20

13/21

13/22

1st D7:D0 /

D7:D0

2nd D7:D0 /

D7:D0

3rd D7:D0 /

D7:D0

12/17

12/18

12/19

1st D7:D0 /

D7:D0

2nd D7:D0 /

D7:D0

3rd D7:D0 /

D7:D0

11/14

11/15

11/16

3rd D7:D0 /

D7:D0

10 D3:D2

28

10 D3:D2

1st D7:D0 /

D7:D0

2nd D7:D0 /

D7:D0

D4:D3

10 D5:D4

9

32PD3000 / 42PD3000

1st 2nd 3rd 4th

MI0>

*** MAX 8 items on one page.

*** LTI *** picture mode

*** LTI *** picture mode

APC

M01> F01(4:3)

F02(16:9)

F03(C16:9L) 00

F04(T16:9L) 01

F05(14:9)

M02> F06(C14:9L) 00

F07(T14:9L) 01

VE6

VET

M05> BGT

CCT

TCR

DCC

WBC

BSO

00

01

00

01

00

01

00

00

01

01

00

01

00

01

00

00

01

01

00

01

APC switch 0;High APC,

1;Normal wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off)

4:3

WIDE

SCREEN

LETTERBOX

T16:9L

14:9

C14:9L

T14:9L

M04

F08(PAN)

HE2

HE3

HE4

HE5

HE6

HET

VE1

VE2

VE3

VE4

01

F09(14:9LS) 00

PCA

M03> HE1

02

02

01

00

02

02

01

00

02

02 wide mode selected by 16:9 key (0;on, 1;off) wide mode selected by 16:9 key (0;on, 1;off)

PC wide mode 0;NORMAL,

1;REAL, 2;FULL

Horizontal enhancer

DYNAMIC

PANORAMIC

14:9 ZOOM

03

00

03

00

03

00

Horizontal enhancer

DYNAMIC-VIDEO

Horizontal enhancer

NATURAL

00 00 00

Horizontal enhancer

NATURAL-VIDEO

01 01 01

Horizontal enhancer CINEMA FC4 2 D20:D19

02 02 02

Horizontal enhancer CINEMA-

VIDEO

00 00 00 Horizontal enhancer TEXT FC4 2

2 D22:D21 03 03 03 Vertical enhancer DYNAMIC FC4

03 03 03

Vertical enhancer DYNAMIC-

VIDEO

03 03 03 Vertical enhancer NATURAL FC4

03 03 03

Vertical enhancer NATURAL-

VIDEO

2 D22:D21

VE5 03 03 03 Vertical enhancer CINEMA FC4

03 03 03

Vertical enhancer CINEMA-

VIDEO

2 D22:D21

00 00 00 Vertical enhancer TEXT

00 00 00 Brightness/Gradation PDP 27&28

00 00 00 D1&D1

01

1F

01

1F

01

1F

Tracking correction W/B

Warm & Norm

00 00 00 Tracking correction W/B Cool PDP

00 00 00

Black Stretch gain offset

ON&MID

27&28 D0&D0

***

"PDP2_service05" no.52

SPC

M06> PHC

5th

32" values hex

37" values hex

42" values hex

00 00 00

PinP(PC W) picture contrast offset

functions Device

8 D07:D00

PHU

NHU

YU6

80 80 80 Colour phase centre

1A 1A 1A

PAL HUE offset (not available if AV2 is RGB)

FC4

20 20 20 NTSC HUE offset

1D 1D 1D

YCbCr / YPbPr @ 60Hz HUE offset

FC4 8 D07:D00

10

32PD3000 / 42PD3000

1st 2nd

*** YNR *** picture mode

*** CNR *** picture mode

MI1>

*** CTI *** picture mode

3rd 4th 5th

YU5

THU

YHU

FPB

M11> BLT

M12> CE1

M13> YE1

MBC

MBX

COT

MCC

MCX

SAC

SAX

CE2

CE3

CE4

CE5

CE6

CET

YET

YE2

YE3

YE4

YE5

YE6

YE7

YE8

M14> YI1

YI2

YI3

YI4

YI5

YI6

YIT

M15> CI1

CI2

CI3

CI4

CI5

32" values hex

37" values hex


1A 1A 1A

YCbCr / YPbPr @ 50Hz HUE offset

1F 1F 1F TEXT HUE offset

Device

FC4

1F

00

1F

00

1F

00

Components Hue for Asian option

FAVOURITE Peak Brightness

0;Peak, 1:Normal

7F 7F 7F Black level (RGB) FC4

80 80 80 main brightness centre : (50) is used in AUTO adjustment

80 80 80 brightness centre TEXT

7F 7F 7F Contrast (RGB)

FC4

FC4

89

70

40

1F

89

70

40

1F

89

70

40

1F main contrast centre contrast centre TEXT

Saturation centre

NTSC/PAL/RGB/YCbCr TV

50 50 50 Saturation centre TEXT

1F 1F 1F

C-Vert/Horiz enhancer gain

DYNAMIC-TV

10 10 10


DYNAMIC-VIDEO


NATURAL-TV

FC4

FC4

FC4

10

1F

10

10

10

1F

10

10

10

1F

10

10


NATURAL-VIDEO


CINEMA-TV


CINEMA-VIDEO


TEXT

00 00 00 sharpness centre - TEXT

1F 1F 1F sharpness DYNAMIC-TV

12 12 12

sharpness DYNAMICT-

VIDEO

FC4

12 12 12 sharpness NATURAL-TV FC4

12 12 12 sharpness NATURAL-VIDEO FC4

12 12 12 sharpness CINEMA-TV FC4

12 12 12 sharpness CINEMA-VIDEO FC4

12 12 12 sharpness centre-

FAVOURITE-TV

12 12 12 sharpness centre-

FAVOURITE-VIDEO

01 01 01 YNR input gain DYNAMIC FC4

01 01 01

YNR input gain DYNAMIC-

VIDEO

01 01 01 YNR input gain NATURAL FC4

01 01 01

YNR input gain NATURAL-

VIDEO

01 01 01 YNR input gain CINEMA FC4

01 01 01

YNR input gain CINEMA-

VIDEO

01 01 01 YNR input gain TEXT

00 00 00 CNR input gain DYNAMIC FC4

00 00 00

CNR input gain DYNAMIC-

VIDEO

00 00 00 CNR input gain NATURAL FC4

00 00 00

CNR input gain NATURAL-

VIDEO

00 00 00 CNR input gain CINEMA FC4

8 D07:D00

5 D07:D00

7 D15:D08

6 D07:D00

7 D07:D00

7 D07:D00

8 D14:D08

2 D04:D00

2 D04:D00

2 D04:D00

2 D04:D00

2 D04:D00

2 D07:D05

2 D07:D05

2 D07:D05

2 D15:D13

2 D15:D13

2 D15:D13

11

32PD3000 / 42PD3000

1st 2nd

MI3>

3rd

MI2>

[ ];menu related value - decimal it is ok to display by hex e.g. [32] is centre of CONTRAST e.g. [63] is MAX for

CONTRAST.

CIT

M16 OSH

OSV

OTH

OTV

SUR

CMB

M21> DCN

DBR

DCL

DPB

DCM

DBS

M22> NCN

4th 5th

CI6

DWB

DFT

NBR

NCL

NPB

NCM

NBS

NWB

NFT

M23> TCN

TBR

TCL

TPB

TCM

TBS

TWB

TFT

M24> DGS

NGS

TGS

PGS

DPM

NPM

TPM

PPM

M31> MVB

32" values hex

37" values hex


00 00 00

CNR input gain CINEMA-

VIDEO

00 00 00 CNR input gain TEXT

109 109 109 H position - OSD

40 40 40 V position - OSD

190 190 190 H position - TEXT

40 40 40 V position - TEXT

00 00 00

SURROUND ON:1, OFF:0

01 01 01 COMB FILTER ON:1, OFF:0

3E 3E 3E

DYNAMIC Contrast

80 80 80 DYNAMIC Brightness

50 50 50 DYNAMIC Colour

00 00 00

DYNAMIC Peak Brightness

0;Peak, 1:Normal

02

1F

00

02

1F

00

02

1F

00

DYNAMIC Contrast Mode

NORM;0, AUTO;1, DYN;2

DYNAMIC Black stretch 0;off,

01~3F; level

DYNAMIC White Balance

0:cool, 1;normal, 2;warm

01 01 01

DYNAMIC Film Mode 0;on,

1;off

38 38 38 NATURAL Contrast

80 80 80

NATURAL Brightness

48 48 48 NATURAL Colour

00 00 00

NATURAL Peak Brightness

0;Peak, 1:Normal

01 01 01

NATURAL Contrast Mode


1A

00

01

1A

00

01

1A

00

01

NATURAL Black stretch 0;off,

01~3F; level

NATURAL White Balance


NATURAL Film Mode 0;on,

1;off

3E 3E 3E CINEMA Contrast

80 80 80 CINEMA Brightness

50 50 50 CINEMA Colour

00

00

1F

01

00

01

01

00

01

01

00

01

01

CINEMA Film Mode 0;on,

1;off

DYNAMIC Gamma Select

NATURAL Gamma Select

01 01 01 CINEMA Gamma Select

02 02 02 PERSONAL Gamma Select

00

01

01

00

00

1F

01

00

01

01

00

00

1F

01

00

01

01

CINEMA Peak Brightness

0;Peak, 1:Normal

CINEMA Contrast Mode


CINEMA Black stretch 0;off,

01~3F; level

CINEMA White Balance


DYNAMIC Picture Mode

NATURAL Picture Mode

CINEMA Picture Mode

02 02 02 PERSONAL Picture Mode

0B 0B 0B MUSIC Volume Balance

12

Device

32PD3000 / 42PD3000

1st 2nd

Those values are fixed in this menu.

MI4>

TDA9178 option

3rd

[ ];menu related value - decimal it is ok to display by hex e.g. [11] is centre of Balance e.g. [21] is MAX for Treble.

M32> NVB

M33> TVB

M41 >

4th 5th

MTR

MBA

MTB

MMS

NTR

NBA

NTB

NMS

TTR

TBA

TTB

TMS

TSW

TC1

TC2

TC3

32" values hex

37" values hex


0B 0B 0B MUSIC Treble

00 00 00

0B 0B 0B MUSIC Bass

03 03 03

MUSIC TruBass 0;off, 1;low,

2;mid, 3;high

01

0B

01

0B

01

0B

MUSIC Matrix Surround 0;off,

1;on

SPEECH Volume Balance

10 10 10 SPEECH Treble

0B 0B 0B SPEECH Bass

SPEECH TruBass 0;off, 1;low,

2;mid, 3;high

00 00 00

SPEECH Matrix Surround

0;off, 1;on

0B 0B 0B CINEMA Volume Balance

10 10 10

CINEMA Treble

10 10 10 CINEMA Bass

02 02 02

CINEMA TruBass 0;off,

1;low, 2;mid, 3;high

01 01 01

CINEMA Matrix Surround

0;off, 1;on

00 00 00

TDA9178 fitted or not. 0:not fitted, 1;fitted

01 01 01

TDA9178 address 00

10 10 10

TDA9178 address 01

00 00 00

TDA9178 address 02

Device

TDA9178

TDA9178

TDA9178

00 00 00

TDA9178 address 03 TDA9178

No individual parameter on

TC1~TC4 can be set.

TC4

ABS

M42 > NLA

VGM

PKG

STP

CRG

LWD

WB OFFSET OFF/1/2/3 option M43> 1RD

1GD

1BD

1RG

1GG

1BG

M44> 2RD

2GD

2BD

2RG

2GG

2BG

00 00 00

TDA9178 address 04

00 00 00

TDA9178 address 05

20 20 20

TDA9178 address 06

00 00 00

TDA9178 address 07

00 00 00

TDA9178 address 08

00 00 00

TDA9178 address 09

00 00 00

TDA9178 address 0A

14 14 14

White balance offset 1;

R_DRIVE MAX

0F

00

1F

1F

1F

00

00

00

1F

1F

1F

0F

00

1F

1F

1F

00

00

00

1F

1F

1F

0F

00

1F

1F

1F

00

00

00

1F

1F

1F


G_DRIVE


B_DRIVE


R_GAMMA


G_GAMMA


B_GAMMA


R_DRIVE CENTRE


G_DRIVE


B_DRIVE


R_GAMMA


G_GAMMA


B_GAMMA

TDA9178

TDA9178

TDA9178

TDA9178

TDA9178

TDA9178

TDA9178

00

01

02

03

D07:D00

D05:D00

D07:D00

D05:D00

04

05

06

07

08

D05:D00

D05:D00

D05:D00

D05:D00

D05:D00

09 D05:D00

0A D05:D00

13

32PD3000 / 42PD3000

1st 2nd

14

MI5>

OPT> OB0

3rd

add 27 bytes

M45> 3RD

M51 >

M53 > LC1

LC2

M54> DCV

4th 5th

3GD

3BD

3RG

3GG

3BG

CEA

CEB

CEC

CED

CEE

CEF

CEM

YEB

YEC

YED

YEE

YEF

YE9

YE0

LC3

LC4

NCV

TCV

SAV

SAO

M52> YEA

TCO

DCO

NCO

32" values hex

37" values hex


00

0F

29

1F

1F

1F

0D

0D

00

0F

29

1F

1F

1F

0D

0D

00

0F

29

1F

1F

1F

0D

0D


R_DRIVE MIN


G_DRIVE


B_DRIVE


R_GAMMA


G_GAMMA


B_GAMMA


DYNAMIC-RGB/YCbCr


DYNAMIC-YPbPr

0D

0D

0D

0D

0D

0D

0D

0D

0D


NATURAL-RGB/YCbCr


NATURAL-YPbPr


CINEMA-RGB/YCbCr

0D

08

0D

08

0D

08


CINEMA-YPbPr

10

10

10

10

10

10

CTI MID level in menu

(FAVOURUTE) sharpness DYNAMIC-

RGB/YCbCr

10 10 10 sharpness DYNAMIC-YPbPr sharpness NATURAL-

RGB/YCbCr

02 02 02 sharpness NATURAL-YPbPr

10 10 10 sharpness CINEMA-

RGB/YCbCr

10 10 10 sharpness DYNAMIC-YPbPr

10 10 10 sharpness centre on

FAVOURITE-RGB/YCbCr

10 10 10 sharpness centre on

FAVOURITE-YPbPr

1F 1F 1F

Favourite + TV ; last CTI

10 10 10

Favourite + Video ; last CTI

0D 0D 0D

Favourite + RGB/YCbCr ; last

CTI

0D 0D 0D

Favourite + YPbPr ; last CTI

50

3E

40

50

3E

40

50

3E

40

DYNAMIC + VIDEO/RGB ; color

NATURAL + VIDEO/RGB ; colour

CINEMA + VIDEO/RGB ; colour

3E

58

4B

50

44

3E

58

4B

50

44

3E

58

4B

50

44

FAVOURITE + VIDEO/RGB ; colour

DYNAMIC + YCbCr/YPbPr ; colour

NATURAL + YCbCr/YPbPr ; colour

CINEMA + YCbCr/YPbPr ; colour

FAVOURITE + YCbCr/YPbPr

; colour

78 78 78 option byte 1

Device

32PD3000 / 42PD3000

FC4

ASIAN

OPTIONS>

HOT> OPT

VOL

PRG

VRS> MN

MSU

PDU

PWT

E2> E2R

E2F

E2S

E24

EXS

1st 2nd 3rd

OB1

EMG

AV DELAY

RGB Comb

4th 5th

32" values hex

37" values hex


80 80 80 option byte 2

0 0 0

0:Normal, 1:Macrovision

improved

OFF OFF OFF

OFF OFF OFF

ON;Go through Comb,

OFF;skip Comb

It is affected to

SVC>MIS>MI1>M11=HP2/4

Enters FC4 sub menu

AV2 RGB RGB RGB RGB or YUV

Device

INITIAL INSTALL ON ON ON

COUNTRY

SELECT

LANGUAGE

SELECT

TELETEXT bar

ON

ON

0

ON

ON

0

ON

ON

0

INITIAL INSTALL menu is on or off

Country select is on or off

European language select is on or off

centre centre centre

Maximum volume limited in

Hotel mode

ON ON ON TELETEXT is working or not hotel option, see sheet HOTEL

OPTION

1 1 1 start up position number

read read read Model name

read read read MSU micro version number

read read read PDP micro version number -

read read read PDP working hour

OK OK OK

EEPROM reset

OK OK OK EEPROM factory setting

OK OK OK

EEPROM is set to the shipment

OK OK OK

EEPROM in FC4 is

initialised

OK OK OK escape from service menu

15

32PD3000 / 42PD3000

Block Diagrams

AVC to PDP Block Diagram

16

AVC Block Diagram

32PD3000 / 42PD3000

17

32PD3000 / 42PD3000

AVC Power Block Diagram

18

Major Connectors

32PD3000 / 42PD3000

19

32PD3000 / 42PD3000

Monitor Block Diagram

20

32PD3000 / 42PD3000

Schematic Drawing Descriptions

Schematic Page 1 ; Tuner / Video Chroma

TUN100 Asymmetrical type tuner ; UV1316/A 1G-3 313914716781

supply voltage ; +5V at pin 7 and +33V at pin 9

control by I2C, SDA at pin 5 and SCL at pin 4

SAW100 K3953M

picture carrier 33.90MHz, picture to sound carrier distance 6.5MHz for

standard L

SAW101 K9456M sound carrier 40.40MHz for standard L

VHF/UHF asymmetrical type tuner converts RF input signal to IF signal output

through pin 11.

AGC voltage is supplied at pin1 from IC100 pin62

IF output is going through buffer Q101 to SAW filter SAW100 for VIF at pin 2 and 3

of IC100 and to SAW101 for SIF at pin 63 and 64.

IC100 Video chroma and video switch TDA9321H

supply voltage ; +8V at pin 11 and 48 (AS)

control by I2C, SDA at pin 47 and SCL at pin 46

TR100 TPWA01B - nominal centre freq. Fn1=6.0MHz and fn2=6.5MHz

TR101 TPWA04B - nominal centre freq. Fn1=5.5MHz and fn2=5.742MHz

X100 3.58MHz X'tal

X101 4.43MHz X'tal

* IF demodulator and video chroma

Demodulated video signal is output from pin 10 going to sound traps

There are two sound traps, TR100 for I/L signal and TR101 for BG, output from which are switched by SOUND-SWITCH from IC301 pin 5

After group delay correction at pin 13, it is connected to pin 14 where TV picture is supplied into video switch.

The TV signal from pin13 is also connected to SCART1 as TV signal output.

Quasi Split Sound converted from SIF input is output at pin 5 to connect with sound decoder IC301

H and V sync pulses are output at pin 60 and 61 to go to FC/MSC for synchronization to convert progressive scan. H pulse must be inverted by Q126.

When selecting one of video signal in video switch of IC100, CVBS signal is going to

COMB filter if the video is CVBS PAL/NTSC format.

Then Y/C separated signal is coming back at pin 28 and 29. The clock must be provided from pin 30.

The video or Y/C signal selected pass through video chroma section and finally converted to YUV format at pin 49, 50, 51

IC100 is supplied 4.43MHz and 3.58MHz clock from crystal X100 and X101, which is automatically selected according to the signal received.

2 RGB inputs are also switched at the last stage in IC100. RGB signals are also converted to YUV.

* video switch

21

32PD3000 / 42PD3000 input pin 14 TV signal input pin 16 CVBS - SCART102 (AV2) input pin 18 CVBS - SCART100 (AV3) input pin 20 pin 21 pin 23 pin 24 pin 28

CVBS/Y - SCART101 (AV1) input

C - SCART101 (AV1) input

CVBS/Y - front AV (FRONT) input

C - front AV (FRONT) input

Y - from COMB filter pin 29 C - from COMB filter input pin 15 SCART102 (AV2) pin8 detection control pin 17 SCART100 (AV3) pin8 detection

--- SCART101 (AV1) pin8 detection is done by micro IC704 pin28 output pin 26 go to COMB filter and phono video output pin 32 pin 34 go to micro for TELETEXT decoding go to SCART102(AV2) and SCART100(AV3) as monitor video output output pin 20 L/L' switch for SAW filter in/out at SAW101 control pin 22 micro switch to switch SVHS or CVBS for front AV input

22

32PD3000 / 42PD3000 output output input

IC300 input

Schematic Page 2 ; Sound / AV3 Control

IC301

X300

NICAM/A2 sound decoder and audio switch ; MSP3410

supply voltage ; +5V at pin 18 and pin 51

control by ; I2C, SDA at pin 10 and SCL at pin 9

18.432MHz

* NICAM/A2 decoder and sound control

QSS signal is coming from IC100 to pin 58 through amplifier Q308/307. The signal level at pin 58 should be 0.1 ~ 0.8Vpp.

Sound output L/R at pin 28 and 29 are connected through amplifier Q310/Q312 for L and Q309/Q311 for R to adjust 500mVrms at PL700 pin 4 and 6 In the condition of AV sound input 500mVrms, FM modulation 54%

Sound output L/R at pin 28 and 29 are also connected through IC300 TDA7433 and

IC303 to headphone.

* Audio switch pin 52 SCART101(AV1) sound L input pin 53 SCART101(AV1) sound R input pin 49 SCART102(AV2) sound L input pin 50 SCART102(AV2) sound R input pin 46 SCART100(AV3) sound L input pin 47 SCART100(AV3) sound R input pin 43 front AV (FRONT) sound L inout pin 44 front AV (FRONT) sound R inout pin 55 mono sound input from IC100 pin 37 SCART101(AV1) sound L output pin 36 SCART101(AV1) sound R output pin 34 SCART102(AV2) / SCART3(AV3) sound L output pin 33 SCART102(AV2) / SCART3(AV3) sound R output pin 29 Speaker / Headphone/phone sound L output pin 28 Speaker / Headphone/phone sound R output pin 5 SOUND SWITCH for trap of TV input signal

Basic audio processor ; TDA7433

supply voltage ; +8V at pin 17


Monitor sound L/R outputs for speaker are connected headphone and phone out. IC300 contributes separate volume control pin 6 pin 5

Audio sound L input

Audio sound R input

23

32PD3000 / 42PD3000

****

PL300 output

IC303

IC302

(OPTION) pin 16 Phono sound L output pin 15 Phono sound R output pin 14 Headphone sound L output pin 13 Headphone sound R output

Headphone sound amplifier ; TDA2822D

supply voltage ; +6.5V at pin 2

Headphone sound L/R controlled its level by IC300 are amplified.

front AV video switch

connector for front control PCB

At pin 12 of PL700, CVBS from AV3 is coming.

At pin 11 of PL700, Y from AV3SVHS is coming

At pin 9 indication of SVHS connector insertion is supplied to micro IC704 pin38 and then it controls micro-switch from pin22 of IC100 in order to select Y from pin11 of

PL700 (micro-sw=H) or to select CVBS from pin12 of PL700 (micro-sw=L)

At pin 15 of PL700, C from AV3SVHS is coming to connect to pin 24 of IC100

TDA8440 is the option in the future. This is not used for this model.

24

32PD3000 / 42PD3000

Schematic Page 3 ; Interface Board (component input, progressive sync separation, centre audio channel

)

IC08

XC01

IC02/IC03 input

Sync separation for Component (progressive) input ; TA1370



50KHz

Sync separation for progressive YPbPr input (50Hz and 60Hz) are carried out at

TA1370.

Input video signal is specifically given from AV4 and connected at pin 26 through clamping circuit constituted with QC25~QC28

Sync separation for all input signal other than Progressive input are carried out at

TDA9321 (page1)

TA1370 includes switch of sync signal (H and V) between H/V input (pin I and pin2) from TDA9321 and internal sync separation.

TA1370 outputs H at pin16 and V at pin 28, which are connected to PSF for FC4 board. There are 2 inputs of the connector for each main and sub.

H output at pin 16 on TA1370 is fed to IC10 to shorten H pulse waveform to avoid jittering.

YUV/RGB switch ; TA1287


control by ; DC voltage at pin 9/10/11 and matrix at pin 16

IC02 YUV; Main signal

YUV ; at pin 1/2/3, Y:1Vpp (incl.sync), UV:0.3Vpp

RGB ; at pin 6/7/8, 0.7Vpp

IC03 connect to FC4 through buffers

YUV ; at pin13/14/15, Y:1Vpp (incl.sync), UV:0.3Vpp matrix control of RGB input (YUV can also input. In this case, matrix control should be through) control

IC03 always 1.6V:RGB --> YUV

IC02 0V; external (Components input)

IC04/IC05/IC06 Analogue switch ; BU4066

supply voltage +9V at pin 14

25

32PD3000 / 42PD3000

IC07 Analogue Switch for Sub video ; BU4053


2 inputs, main YUV from IC03 and RGB from micro (TELETXT), are switched and connected to sub video input for FC4

This is enabled when TV+TEXT is selected (SUB TELETEXT), and when PC window is selected (SUB VIDEO)

IC09 I/O expanders ; M62320FP


control by ; I2C, SDA at pin 3 and SCL at pin 2 connect to L

D00 pin 4 component video IC02, IC05 components input

D01 pin 5 Matrix IC02 RGB --> YUV

H

other than components

through

D02 pin 6 PC

D03 pin 7 OSD-blank

D04 pin 9 Cinema

IC07 Not PC mode (SUB TEXT) PC mode (SUB video in PCW)

IC03 kill OSD OSD enabled

IC06, IC04 Audio centre not selected Audio centre selected

D05 pin 10 Clamp-source IC05 CP from TA1370 SC from TDA9321

D06 pin 11 TV/TEXT IC03 TEXT (select RGB input) TV

D07 pin 12 N.C.

26

32PD3000 / 42PD3000

Schematic Page 4 ; Power Circuit (Voltage Regulator) / Level Shifter

Power supply connector PSP from Power Supply board

1 POWER1 Power ON/Stand-by control H;ON, L;Stand-by

2 N.C.

3 N.C.

4 N.C.

5 +5VSTB

6 GND

7 N.C.

8 N.C.

9 GND

10 GND

11 +5.5V1

12 GND

13 +9.5V1

14 GND

15 +5.5V2

16 GND

17 +9.5V2

18 GND

19 FE+30V

Voltage regulators

I603 BA06T

IC602 SI-3050LSA

IC603 SI-3050LSA

IC601 SI-3033LSA

Q602 TK11125M

IC604 BA09FP

Stand-by 5V for micro controller circuit

5.5V supply 1

9.5V supply 1

5.5V supply 2

9.5V supply2

30V supply for tuner

Input +9.5V2 - Output +8V

For video chroma circuit (page1)

Input +5.5V1 - Output +5VFE

For tuner (page1)


For audio processor circuit (page2), comb filter (page6)

Input +5VSTB - Output 3.3VSTB

For micro controller circuit

Input +5VSTB - Output 2.5VSTB

For micro controller circuit


For interface circuit (page 3)

Level shift for control buses

Q607 BSS138

3WB-DATA to change from 3V3 to 5V

Q603 2SC2412K

Q604 2SC2412K

3WB-CLOCK to invert with 5V range

FC-ENABLE to invert with 5V range

Q605 2SC2412K

Q614 BSS138

MSC-ENABLE to invert with 5V range

1900TX to change from 3V3 to 5V

27

32PD3000 / 42PD3000

Schematic Page 5 ; Micro Controller

IC704 Micro controller ; SDA5550 supply voltage ; +3.3VSTB at pin 8, 40, 75 and 92 and +2.5VSTB at pin 6, 22, 56 and 73

control through I

2

C ; SDA3v3 at pin 52 and SCL3v3 at pin 47

3 wire bus ; 3WB-clock3v3 at pin 41 and 3WB-data3v3 at pin 46

FC-enable at pin 42

MSC-enable at pin 43

OSD enable at pin 44

control through/by AVlink ; output at pin 16 and input at pin 33

RS232C (19200bps); TxD3v3 at pin 32 and RxD3v3 at pin 38

control by I/R in ; at pin 34

X700 6MHz X'tal

IC700 EEPROM ; M24C16W (16kbits) supply voltage ; +3.3VSTB at pin 8 control by I2C ; SDA3v3 at pin 5 and SCL3v3 at pin 6 and WC3v3 at pin 7

IC701 Flash memory for software stored ; AT49LV002N (256Kbytes) supply voltage ; +3.3VSTB at pin 32 control by address and data buses

IC701B option not fitted.

IC703 SRAM ; SMT K6T1008V2E-GB70000 or equivalent (128kbytes) supply voltage ; +3.3VSTB at pin 32 control by address and data buses

IC705 RESET IC for IC704 ; M62703SL/ML supply voltage ; +3.3VSTB at pin 1

SCL3v3 and SDA3v3 are converted for 5V operation in Q700/Q701/Q705/Q706

OSD/TEXT RGB at pin 58/59/60 are syncronized with progressive sync pulses 2H(32KHz) at pin 32 and V(50/60Hz) at pin 33

RGB and BLK are also converted to 5V operation at Q713/Q714/Q715 and IC707

AV link is bi-directional bus from pin 10 of SCART101, made by Q709/D701~D703. For the micro, input and output are separated.

The signal level is also converted between 3V3 in micro and 5V for SCART.

See "micro pins" for micro controller pin functions.

FRONT PANEL BOARD connection PL702

PIN

NO.

PIN NAME PL702 IN/OUT

LED

2 POWER

I

SAVE I

3 STB+5V

4 GND

5 RM-IN

6 A+5V

7 A/D KEY 2

I

-

O

I

O

8 A/D KEY 1

9 (BS-LED)

O

-

10 (MODEM-LED) -

at Front Control

FUNCTIONS

POWER2

Stand-by 5V power supply

GND

N.C.

+5V

Key in 1

Key in 2

N.C.

N.C.

28

32PD3000 / 42PD3000

Schematic Page 6 ; COMB Filter / SVHS Output

IC101 COMB filter ; TC9090AF supply voltage ; +5V at pin 15, 18 and 27

CVBS from IC100 pin 26 is filtered by C800/C801/L800/C802 and connected to pin 3

Y/C separate signals output from IC101 pin 25/23 are also filtered by Q801 base circuit and Q802 base circuit

Y is amplified to adjust the level at Q119/Q120 for return signal to

IC100 and SVHS Y signal output via buffer Q803

IC101 requires clock at pin 19 supplied from IC100.

C is amplified to adjust the level at Q121/Q122 for return signal to

IC100 and SVHS C signal output via buffer Q804

SVHS100 SVHS output connector

pin functions

1

2

3

4

5

GND

GND

C

Y

GND(SW)

29

32PD3000 / 42PD3000

Schematic Page 7 ; SCART / FC-MSC Connection

SCART connectors

SCART101 SCART102 SCART100

1

2 sound output

R sound output

R sound output

R

Audio output R ; =<1kohm, nominal

0.5Vrms+-3dB, max 2Vrms ; 54% modulation in FM/AM sound input

R sound input

R sound input

R

Audio input R ; >=10kohm, nominal 0.5Vrms, min.0.2Vrms, max 2Vrms

3 sound output

L sound output

L sound output

L

Audio output L ; =<1kohm, nominal

0.5Vrms+-3dB, max 2Vrms ; 54% modulation in FM/AM

4 GND GND GND Audio common return

6 sound input

L sound input

L sound input

L

Audio input L ; >=10kohm, nominal 0.5Vrms, min.0.2Vrms, max 2Vrms

7 N.C. Blue-in Blue-in Blue ; 75ohm, 0.7V+-0.1V

Function switch ; >=10kohm, =<2nF, Level 0 ;

0~2V, Level 1A : +4.5V~+7V (16:9), Level 1B

: +9.5V~+12V (4:3)

GND GND GND return

10 AVLINK N.C. N.C. Avlink ; TTL level

11 N.C. Green-in Green-in Green ; 75ohm, 0.7V+-0.1V

16 N.C.

Fast

Blanking

Fast

Blanking

Blanking ; 75ohm, logical 0 (off) : 0~0.4V, logical 1 : +1~+3V

17 GND GND GND Video output return

18 GND GND GND Video input return output

Monitor output

Monitor output

Video/Y output ; 75ohm, 1Vpp +-3dB (sync

0.3V-3dB, +10dB)

20 CVBS/Y in CVBS in CVBS in

Video input ; 75ohm, 1Vpp +-3dB (sync 0.3V-

3dB, +10dB)

21 GND GND GND Common return and contact 8, 10, 12

32PD3000 / 42PD3000

PL700 connection with FC/MSC board 26ways connector assuming that 1Vpp video signal with 75ohm terminated is input through SCART100 (AV3)

UV are inverted by Q609/Q612/Q610/Q613 to CbCr(U'V') at pin 25/24 and those are adjusted to the level at 1.4Vpp

Y is amplified by Q608/Q611 to adjust the level at 1.4V for signal and 0.6V for sync (2Vpp in total) at pin 26 sound level L and R at pin 6/4 should be 500mVrms on the condition that -

500mVrms audio is input through SCART100(AV3)

BG FM sound with 54% modulation is received

PL701 connection with FC/MSC board 26 ways connector

31

32PD3000 / 42PD3000

Schematic; AVC Power Supply

I901 switching regulator - controller and power MOS FET ; STR-F6668B

supply voltage at pin 4 ; over +16V (start operating) pin 2 pin 3 pin 4

Source of power MOS FET

Drain of power MOS FET power supply input for controller

H901 DC+5V switching regulator module ; uPM0518SA

supply voltage ; DC +120+375V at pin 1 input pin 1 pin 5

DC(+) voltage input

DC(-) voltage input output pin 6 pin 9

DC(-) voltage output

DC(+) voltage output

I902 photocoupler ; TLP621

I930 switching regulator ; SPI-8010A

supply voltage ; DC +8.5+50V at pin 11 input pin 11 DC voltage input output pin 7 switching output

I931 switching regulator ; SI-8010GL

supply voltage ; DC +8+50V at pin 5 input pin 5 DC voltage input output pin 4 switching output

I932 DC+5V series regulator ; SI-3050LSA

supply voltage ; DC +5.1+8V at pin 1,3 input pin 1,3 output pin 7,8

DC voltage input

DC +5V output

I933 switching regulator ; SI-8033JD

supply voltage ; DC +5.3+40V at pin 1 input pin 1 DC voltage input output pin 2 switching output

PSP connector for AV P.W.B.

PFP1 connector for FC4 unit

PFP2 connector for FC4 unit

32

Schematic Drawings

32PD3000 / 42PD3000

33

32PD3000 / 42PD3000

34

32PD3000 / 42PD3000

35

32PD3000 / 42PD3000

36

32PD3000 / 42PD3000

37

32PD3000 / 42PD3000

38

32PD3000 / 42PD3000

39

32PD3000 / 42PD3000

40

32PD3000 / 42PD3000

41

32PD3000 / 42PD3000

42

32PD3000 / 42PD3000

43

32PD3000 / 42PD3000

44

32PD3000 / 42PD3000

45

32PD3000 / 42PD3000

46

Circuit Boards

32PD3000 / 42PD3000

47

32PD3000 / 42PD3000

48

AV Power Side A

32PD3000 / 42PD3000

49

32PD3000 / 42PD3000

AV Power Side B

50

Monitor block SIGNAL/SOUND board [ side - A ]

L K J I H

6

5

G F

SIGNAL/SOUND board is 4 layered.

The inner layer is not recorded.

E D C B A

6

5

4

3

2

1

4

3

2

1

L K J I H G F E D C B A

Main chip component location search chart

Cir.No.

Position

D003

D401

D402

D403

D404

D405

D406

D408

D409

D410

D413

D414

D415

D600

D601

J2

J2

I3

I1

H4

K2

C4

K4

K3

K3

K4

J4

I3

E1

E1

Cir.No.

Position

D602

D603

D604

D605

D606

D607

D610

D611

DP01

DS01

DS02

DS03

DS04

I001

I002

D2

D2

F5

A2

A2

A3

F1

F1

E1

E1

F1

E1

B4

C3

B3

Cir.No.

Position

I003

I201

I202

I600

I601

I602

I603

IC401

IC402

IC403

IP02

L201

L202

L203

L204

D1

H2

J2

J1

F5

B5

C4

D5

B5

E2

G2

G3

B5

D5

C5

Cir.No.

Position

L600

L601

L602

L603

L604

LP02

LP04

PDA1

PDS

PSC2

Q001

Q002

Q003

Q005

Q006

E5

H6

A5

G6

C4

C2

D2

E2

E2

E3

G3

F4

C2

G5

G5

Cir.No.

Position

Q201

Q202

Q203

Q204

Q401

Q402

Q403

Q404

Q405

Q406

Q407

Q408

Q600

Q601

Q602

J3

K1

K1

I3

H4

J3

D4

D4

C6

C6

I4

J4

F2

F2

G2

Cir.No.

Position

QP01

QS04

TP001

TP002

TP601

X001

X002

X201

X202

X203

X204

X600

X601

X602

X603

D3

B5

B5

B5

C4

G1

E5

A2

D3

C4

D2

G5

G1

G1

G1

Cir.No.

Position

X604

X605

XS01

XS02

XS03

G1

F1

A2

B1

B1

Monitor block SIGNAL/SOUND board [ side - B ]

A B C D E

6

5

F G

SIGNAL/SOUND board is 4 layered.

The inner layer is not recorded.

H I J K L

6

5

4

3

2

1

4

3

2

1

A B C D E F G H I J K L

Main chip component location search chart

Cir.No.

Position

D001

D608

D609

QS01

D3

F2

F2

B4

FILTER board LED board for 32V

LED board for 42V

SPEAKER TERMINAL (R) bord (only 42V)

SPEAKER TERMINAL (L) bord (only 42V)

32PD3000 / 42PD3000

Assembly Drawings

Audio / Video

58

Wiring for Audio / Video Components

EFP1, EFP2, ESC and

EARTH should never be bunched together with ZSC

(Nittoh adhesive tape No.188

L=50mm)

Lead clamper for EFP1, EFP2,

ESC and EARTH should be locked after fixing EARTH and looped

EFP1, EFP2 and ESC wires.

10

150

10

32PD3000 / 42PD3000

Specification

1. This Drawing shows the wire dressing and connectors' connection of

AVC3-E Final Assy.

2. Connectors with wire should be inserted into Plug Pin Posts as shown on the table below

Connector with wire

Name Assy List

ESC FINAL ASSY

EFP1 FINAL ASSY

Plug Pin 1

Board

EFP2 FINAL ASSY

ESF FINAL ASSY

Power Board

Power Board

AV Board

PSP Power Board Assy AV Board

Plug Pin 2

Name Board

Control Board PSC AV Board PL702

PFP1 HCP111

PFP2 HCP111

PSF

PSP -

HCP111

-

Name

P002P

P003P

P001

3. Into Plug Pin Post with Lock function, connector housing should be inserted deeply until it can be locked.

4. Into Plug Pin Post without Lock function, connector housing should be inserted most deeply.

5. Flexible Flat Cable ESF should be fixed as shown on the drawing below position and lock

59

32PD3000E

42PD3000E

32PD3000E Monitor Block

The codes in brackets shown in the wiring diagram express the name of materials.

The key to the codes and materials is shown on the table below.

Code

PC+ABS

PS

Material

POLYCARBONATE+

ACRYLONITRILE BUTADIENE STYRENE

POLYSTYRENE

(PS)

(PC+ABS)

(PS)

SIGNAL Board

32PD3000E

42PD3000E

AC INLET

FILTER Board

LED Board

Colored metal plate

32PD3000E

42PD3000E

42PD3000E Monitor Block

(PC+ABS)

The codes in brackets shown in the wiring diagram express the name of materials.

The key to the codes and materials is shown on the table below.

Code

ABS

PC+ABS

AL

Material


POLYCARBONATE+


ALUMINUM

PDP Panel Module

Assembly

POWER UNIT

32PD3000E

42PD3000E

SIGNAL/SOUND

Board Assembly

(ABS)

(PC+ABS)

(PC+

ABS)

(AL)

(PC+ABS)

(PC+

ABS)

(ABS)

(PC+ABS)

(PC+ABS)

32PD3000 / 42PD3000

32 inch Monitor Wiring A

62

32 inch Monitor Wiring B

32PD3000 / 42PD3000

63

32PD3000 / 42PD3000

42 inch Monitor Wiring A

64

32PD3000 / 42PD3000

65

32PD3000 / 42PD3000

24 way Digital Interface Cable

Connection

AVC(FC4)

P301P

DV174320-4004

1 TX2-

2 TX2+

PDP

TX2-

TX2+

3 SHIELD

4 N.C.

5 N.C.

6 SCLH

--- SHIELD

--- N.C.

--- N.C.

SCLH

7 SDAH

8 N.C.

9 TX1-

10 TX1+

SDAH

--- N.C.

TX1-

TX1+

11 SHIELD

12 N.C.

--- SHIELD

--- N.C.

13 N.C.

--- N.C.

14 +5VAVDET +5VAVDET

15 GND

16 HPDET

17 TXD-

18 TXD+

19 SHIELD

20 N.C.

21 N.C.

22 SHIELD

23 TXC+

24 TXC-

--- GND

HPDET

TXD-

TXD+

--- SHIELD

--- N.C.

--- N.C.

--- SUIELD

TXC+

TXC-

AVC(FC4)

P302P

TC57587-01-401

1 TXD

PDP

TXD

2 RXD

3 PARITY

4 REMO-PDP

5 AUDIO L

RXD

PARITY

REMO-PDP

AUDIO L

6 AUDIO R

7 PDDET

8 AVDET2

AUDIO R

PDDET

AVDET2

66

32PD3000 / 42PD3000

Microprocessor Pins

Pin

No.

FUNCTION

INVERTED (I)

OR BUFFERED

(B)

FUNCTION

IN/OUT

Port 0

9

0.

0

POWER-

ON

10

0.

1

11

12

13

0.

2

0.

3

0.

4

POWER1 OUT

POWER2

(I) POWER-

LED 5V

(I) OSD-

RESET

IN

OUT

OUT

OUT

Power key input

Power control

1

Power control

2

H(1.0V)

Power LED control

H(1.5V)

H(1.5V)

PC OSD reset on standby

L power save

H(1.2V)

L L

H(1.5V) H(1.5V)

14

0.

5

15

0.

6

16

0.

7

WC#

EEPROM

AV-LINK-

OUT

(I) PM-RESET OUT

OUT

(I) AV LINK OUT

PDP reset

EEPROM enable

AV link output

Port 1

41

1.

0

3WB-

CLOCK

(I) 3WB-

CLOCK 5V

OUT

3 wire bus clock

42

43

1.

1

1.

2

FC-

ENABLE

MSC-

ENABLE

(I) FC-

ENABLE 5V

(I) MSC-

ENABLE 5V

OUT

OUT

FC enable

MSC enable

44

1.

3

45

1.

4

46

1.

5

47

1.

6

3WB-

DATA

(I) OSD-EN OUT

(I) MSP-RESET OUT

(B) 3WB-

DATA+5V

SCL-3V3 (B) SCL+5V

52

1.

7

Port 2

SDA-3V3 (B) SDA+5V

24

2.

0

ADC0

FROM

SCART1 PIN 8

IN/OU

T

OUT

IN/OU

T

IN

PC OSD enable

MSP3410 reset

3 wire buses data

I2C bus clock

I2C bus data

Scart 101

(AV1) pin 8 detect

67

32PD3000 / 42PD3000

25

26

27

2.

1

2.

2

2.

3

ADC1

ADC3

FROM TUNER

AGC

FROM FRONT

SWITCHES

IN

IN

AGC level detect

PDP ON detect

Vol+/-

&Prog.+/- key input

Port 3

31

3.

0

IF TRAP

ADJACENT

CHANNELS

OUT Not used

32

3.

1

1900TX-

3v3

OUT

PDP communicatio n via RS232C

33

3.

2

34

3.

3

35

3.

4

FRONT-

SVHS-

SOCKET

36

3.

5

37

3.

6

SCI

IR1

MAP1

MAP2

FROM

AVLINK

IR FROM PDP IN

38

3.

7

1900RX

Port 4

48

4.

2

MEM RD#

49

4.

3

MEM WR#

IN

IN

AV link input

IR input

S-VHS socket detect

A18 ON SRAM OUT

A15/A18

SWITCH

OUT

IN

OUT

OUT

SRAM mapping

SRAM mapping

PDP communicatio n via RS232C

SRAM output enable

SRAM write enable

68

32PD3000 / 42PD3000

Connections to FC4

PSF at AVC P001 at FC4

Pin

No.

PIN NAME PIN NAME

1 GND GND

2 N.C.

3 GND

4 DATA

5 CLK

6 GND

N.C.

GND

DATA

CLK

GND

7 FC-ENA

8 MSC-ENA

9 DATA

10 CLK

11 GND

12 N.C.

FC-ENA

OSD-CS

OSD-DATA

OSD-CLK

GND

N.C.(2H)

IN/OUT FUNCTIONS NOTE

I/O I 2 C bus DATA

I/O I

2

C bus CLOCK

- GND

I/O 3 wires DATA

I 3 wires CLOCK

- GND

5V CMOS

5V CMOS

I

I

I

I

FC micro enable

MSC micro enable 5V CMOS

3 wires DATA

3 wires CLOCK

- GND

5V CMOS

5V CMOS

5V CMOS

O 2H sync for OSD

13 N.C. K_DET

O 2V sync for OSD 14 N.C.

15 N.C.

16 GND

N.C.(2V)

KMASK

GND

32C-PDP (TXD)

- GND

I RS232C-TxD 5V CMOS

32C-PDP (RXD)

19 GND

20 +5VSTB

21 N.C.

GND

AVDET

N.C.

22 Remo-PDP Remo-PDP

23 GND

24 PM RST

25 PD DET

26 GND

27 MY

28 MCb

29 MCr

N.C.

PM RST

PD DET

GND

MY

MCb

MCr

O RS232C-RxD

- GND

I PDP control

I MATRIX control

- GND

I

O

PDP control

PDP control

- GND

5V CMOS

5V CMOS

5V CMOS

5V CMOS

1.4V±0.06Vp-p

0.7v±0.03Vp-p

0.7v±0.03Vp-p

69

32PD3000 / 42PD3000

30 GND

31 MH

32 MV

33 GND

34 SY

GND

MH

MV

GND

SY

- GND

I

I

Main H sync

Main V sync

- GND

35 SCb

36 SCr

37 GND

38 SH

39 SV

40 GND

41 GND

42 GND

43 GND

44 GND

SCb

SCr

GND

SH

SV

GND

GND(OSD/TXT

G)

GND(OSD/TXT

B)

GND(OSD/TXT

R)

GND(OSD

BLK/Ys)

- GND

I

I

Sub H sync

Sub V sync

- GND

I GND

I GND

I GND

I GND

45 GND

46 GND

47 AUDIO L

48 GND

49 AUDIO R

GND(OSD/Ym)

GND

AUDIO L

GND

AUDIO R

50 GND

P002P

GND

I GND

- GND

I

I

Audio L

- GND

Audio R

- GND

at FC4

PIN

NO.

PIN NAME

1 FA+6.0V

2 FA+6.0V

3 GND

4 GND

5 FSTB+5V

6 FSTB+5V

7 GND

IN/OUT FUNCTIONS

I

I

-

-

I

I

-

6V power supply

6V power supply

GND

GND

Stand-by +5V

Stand-by +5V

GND

NOTE

460mA

50mA typ 500mVrms typ 500mVrms

5V CMOS

5V CMOS

1.4V±0.06Vp-p (Y) /

0.7Vpp±0.03Vpp (G)

0.7v±0.03Vp-p

0.7v±0.03Vp-p

5V CMOS

5V CMOS

70

P003P

PIN

NO.

PIN NAME

1 D+1.8V

2 D+1.8V

3 GND

4 GND

5 D+3.3V

6 D+3.3V

7 D+3.3V

8 GND

9 GND

32PD3000 / 42PD3000

at FC4

IN/OUT FUNCTIONS

I

I

-

I

-

I

I

-

-

NOTE

1.8V power supply 500mA

1.8V power supply

GND

GND

3.3V power supply 350mA

3.3V power supply

3.3V power supply

GND

GND

71

32PD3000 / 42PD3000

PCB Connectors

AVC

ESC 2908877

FINA

L

ASS

Y

EFP

1

EFP

2

EF22161

EF22171

FINA

L

ASS

Y

FINA

L

ASS

Y

CO-10C-C2R0-431

Contr ol

Board

PSC

EA00069

R

CO-07C-C1R5-

391-ZH

CO-09C-C1R5-

391-ZH

ESF EK01108

FINA

L

ASS

Y

PSP

ED04153

U

PRW-SML2CD-

50P-L700

Powe r

Boar d

CP-

19BP1R2VU1.25F

JN

FC4

Power

Board

PFP

1

Power

Board

PFP

2

EA01246

R

EA01248

R

AV

Board

PSF

EA00932

R

AV

Board

PSP

ED04163

U

CPC10PH2R0HTP

H-SM3

CPC07BP1R5VT-

SM3

CPC09BP1R5VT-

SM3

CPC50FP0R5VT-

FH12

CP-

19BS1R2VU1.25F

JN

AV

Boar d

PL70

2

FC4

P002

P

FC4

P003

P

EA00349

R

CPC10PH2R0VTP

H-SM3

EA01266

R

EA01268

R

FC4 P001

EA01561

R

- - -

CPC07BP1R5HT-

SM3A

CPC09BP1R5HT-

SM3A

CPC50FP0R5HT-

FLZX

-

P002P EA01266R CPC07BP1R5HT-SM3A PFP1 Power Board

P003P EA01268R CPC09BP1R5HT-SM3A PFP2 Power Board

P301P EY01501 PJX-DVI(F)24P RA SOK PDP Signal Audio Board

P302P EY01491 PJX-YKF51-5376

P501P EA01247R CPC08BP1R5VT-SM3

P601P EY01062 PJX-DSUB JACK

AV Board

PDP Signal Audio Board

For Alignment

PC Input Terminal

PL702 EA00349R CPC10PH2R0VTPH-SM3 PSC ControlBoard

Power Control Board

PFP1 EA01246R CPC07BP1R5VT-SM3 P002P FC4

PFP2 EA01248R CPC09BP1R5VT-SM3 P003P FC4

PSC EA00069R CPC10PH2R0HTPH-SM3 PL702 AV Board

72

32PD3000 / 42PD3000

Replacement Parts

Signal / Sound Board

CIR No. DESCRIPTION ECN#[040] Part No.

# PSA PT3 SIGNAL/AUDIO JP06091

# "PSA PT3 SIGNAL/AUDIO FOR ""42"


JP06092


B PWB PT3 SIGNAL/AUDIO JA04554

CP01 470UF 25V ALUMINIUM ELECTROLYTIC CAPACITOR

AL01857R

CP02 1000UF 6.3V ALUMINIUM ELECTROLYTIC

CAPACITOR AL01833R

CP04 CCC106M06-B-20CT (10UF 6.3V 2012M) AA00968R

CP05 CEC101M06-EWCT AD00416R



CS02 CEC100M16-EWCT AD00436R

CS03 CAP2125CHIP 10000PFKB 50V TAPE 0893044R

CS04 CEC101M16-EWCT AD00441R

CS07 CCC333K50-B-16CT AA01814R

CS10 CCC106M06-B-20CT (10UF 6.3V 2012M) AA00968R

C001 CAP 1608CHIP 10PFCCH 50V TAPE 0893113R

C002 CAP 1608CHIP 10PFCCH 50V TAPE 0893113R

MCH18 AA01802R

C004 CERAMIC CAPACITOR(1.0UF 6.3V) AA01111R

MCH18 AA01802R

C008 CCC103K50-B-16CT

C010 CCC103K50-B-16CT

C011 CCC103K50-B-16CT








C211 CEC101M06-EWCT AD00416R

C401 CAP 1608CHIP 470PFJCH 50V TAPE 0893135R


C403 CEC4R7M25-EWCT AD00447R


C405 CAP 1608CHIP 1500PFKB 50V TAPE 0893211R

C406 CAP 1608CHIP 1500PFKB 50V TAPE 0893211R

C407 CERAMIC CAPACITOR(0.47UF 10V) AA01121R

C408 CERAMIC CAPACITOR(0.47UF 10V) AA01121R




C412 CCC333K50-B-16CT





0800344R C417 CAP.-ELECTRO. 330UF-M(SMG) 16V




AA01814R

C422 CCC333K50-B-16CT

C423 CCC333K50-B-16CT AA01814R

C424 CCC333K50-B-16CT

C425 CCC333K50-B-16CT

C426 CCC333K50-B-16CT

AA01814R

C428 CCC103K50-B-16CT




C432 CAP.-ELECTRO. 330UF-M(SMG) 16V


0800344R





C440 CAP.-POLYESTER 1.0UF-J 50V 0880207R




C444 CAP.-POLYESTER FILM 0.22UF-K 50V 0880018R

C445 CAP.-POLYESTER FILM 0.22UF-K 50V 0880018R



AA01814R


AA01814R

AA01814R

C457 CCC333K50-B-16CT


C459 CCC333K50-B-16CT

C460 CCC333K50-B-16CT

C461 CAP.-ELECTRO.470UF-M

C462 CAP.-ELECTRO.470UF-M 0800353R


C464 CCC333K50-B-16CT

C467 CAP.-ELECTRO

C468

C469

C470

C473

16V 0800361N

CERAMIC CAPACITOR(1UF 10V-F) AA01101R

CAP 1608CHIP 1500PFKB 50V TAPE 0893211R

CAP 1608CHIP 1500PFKB 50V TAPE 0893211R

2200UF 10V ALUMINIUM ELECTROLYTIC

CAPACITOR AL01843R

C474 2200UF 10V ALUMINIUM ELECTROLYTIC

CAPACITOR AL01843R


CAPACITOR AL01843R


CAPACITOR AL01843R

C482 CAP.-POLYESTER 0.01UF-K 50V 0880009R

C600 CCC333K50-B-16CT

MCH18 AA01802R

C605 CCC103K50-B-16CT

C606

AA01814R

C601 CCC333K50-B-16CT

C602 CCC103K50-B-16CT

C603 CCC103K50-B-16CT

C604 CCC103K50-B-16CT

MCH18 AA01802R

CAP2125CHIP 10000PFKB 50V TAPE 0893044R


C608 CCC103K50-B-16CT


AA01814R


AA01814R

C613 CCC333K50-B-16CT

C627

C628

C629

AA01814R

C614 CCC333K50-B-16CT

C615 CCC333K50-B-16CT

C616 CCC333K50-B-16CT

CERAMIC CAPACITOR(1.0UF 6.3V) AA01111R




C631 CCC333K50-B-16CT

C632 CCC333K50-B-16CT

C633 CCC333K50-B-16CT

DP01 DIODE

AA01814R

SFPJ-73 CC01661R

1SS355

DS02 DIODE.CHIP CC00003R

DS04 CHIP DIODE RD5.1UM(B2-T) CC00142R

D001 DIO-1S2835(T2B)

D003 DIODE.CHIP CC00003R

D401 DIODE.CHIP RB491D (20V) CC00632R




1SS355


D407 DIODE AM01Z (200 TAPE) 1A 2339491M

1SS355


D410 ZENER.CHIP UDZ 7.5B CC00826R



D600 DIODE CHIP DA204K-TPTX CC10721R










1SS355


NJW1138M CK36481R IC401 IC

IC402 NJM2192AM

CK31991R

CK35311R

IC403 ANALOG MONOLITHIC IC BU4052BCF-E2

73

32PD3000 / 42PD3000

POWER

IP02 MONO IC SI-8033JD CK37162R

IS01 ANALOG MONOLITHIC IC (BA6956AN) CP08241U

I001 DIGITAL MONOLITHIC IC (HD64F3397) CK06571U

I002 DIGITAL MONOLITHIC IC (M24C16-WMN6T)

CK32542R

I003 DIGITAL MONOLITHIC IC (PST9142-T(FP)) CK06091R

I201 DIGITAL MONOLITHIC IC (HD74LVC244AT) CK32661R

I202 DIGITAL MONOLITHIC IC (THC63LVDM83R)

CK32072R

I600 DIGITAL MONOLITHIC IC (SII169) CK37891U

I602 DIGITAL MONOLITHIC IC (DS14C232CM) CK04681R

I603 ANALOG MONOLITHIC IC(PST9127NR) CK06097R

JSW 1.5MM PITCH 13P FG CONNECTOR SOCKET ED04241

J401 JAK-YKC21-1P-BLK 2672967

J601 CONNECTOR ED03473

J602 SOCKET YKF51-5376 EY01491

KP04 0.60MM TAPED JUMP.WIRE 2784381M

K208 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R



K211 0.60MM TAPED JUMP.WIRE 2784381M



















LP02 C12-K4.5L SMD COIL 100UH BA00632R

LP03 FILT.COIL(LHL08 2125806N

LP04 3225 CHIP COIL 47UH BA00712R

47UH)

LS02 COIL FERRITE BEAD BL02RN1-R62T4 BZ01421R

L201 3225 CHIP COIL 47UH BA00712R




L401 COIL 10UH 2.1A BH01811R

L402 COIL 10UH 2.1A BH01811R

L403 COIL 10UH 2.1A BH01811R

L404 COIL 10UH 2.1A BH01811R

L409 COIL FERRITE BEAD BL02RN1-R62T4 BZ01421R




L415 DC COM. MODE CHOKE COIL 7UH 2A BZ05521

L416 DC COM. MODE CHOKE COIL 7UH 2A BZ05521





N401 SOUND 3000

N403 M3X10 SCREW WITH WASHER 4520889

PAS1 PLUG PIN SUB MINI 2P 2902261

PAS2 PLUG 03P EH TAPE 2902262R

PDA1 1.5MM PITCH 12P CONNECTOR BASE SM3 EA01252R

PDS CONNECTOR DF13-20DP-1.25V(59) EA01092R

PG2 PLUG 02BP3R9V-VH(PBT) ED01531

PMW PLUG 07P EH TAPE 2902266R

PPA PLUG 04P EH TAPE 2902263R

PPS PLUG PIN SUB MINI 9P 2902268

CPC06PH2R0VTPH-SM3

PSU 5P XH CONNECTOR PLUG B 5B-XH-A ED03494

2SA1576-T107-R

QS04 TRS.CHIP DTC144EE TL CA00983R

Q001 TRS.CHIP 2SC4617 TL (R/S) 1323293R

Q005 TRS.CHIP 2SA1774 TL (R/S)

Q006 TRS.CHIP 2SA1774 TL (R/S)

1323294R

1323294R


Q202 TRS.CHIP DTC114EE TL CA00981R

2SK3018 CA01011R

Q204 TRS.CHIP



R036

R039

R042

R043

R044

R046

R047

R048

R053

R054

R055

R059

R063

R064

R065

R019

R020

R022

R023

R024

R025

R026

R027

R028

R029

R030

R032

R035

R002

R004

R005

R005

R006

R007

R008

R009

R014

R015

R016

R017

R018


Q404 TRS.CHIP

Q405 TRS.CHIP CA00771R


DTC323TK


2SK3018 CA01011R

Q601 TRS.CHIP

Q602 TRS.CHIP

RB01 RES.CHIP 1/16W 0 OHM AQ00001R

RB02 RES.CHIP 1/16W 0 OHM AQ00001R

RG01 RES.CHIP 1/16W 0 OHM AQ00001R

RG02 RES.CHIP 1/16W 0 OHM AQ00001R

RP09 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

RR01 RES.CHIP 1/16W 0 OHM AQ00001R

RR02 RES.CHIP 1/16W 0 OHM AQ00001R

RS01 RES.CHIP 1/16W 82K OHM 0790063R


RS03 RES.CHIP 1/16W 100 OHM 0790024R

RS04 RES.CHIP 1/16W 100 OHM 0790024R


RS06 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

RS06 RES.CHIP 1/16W 1.0M OHM 0790077R

RS07 RES.MTL FLM 1W 5.6 OHM AT01049S

RS08 ES.-CARBON FLM 1/2W 1.5-J 0188093M





RS15 RES.CHIP 1/16W 1.0K OHM 0790037R

DQ1SU FJ00291

DQ1SU FJ00291

R0A1 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

R0A6 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

R0A8 RES.CHIP 1/16W 100 OHM 0790024R

R0A9 RES.CHIP 1/16W 10K OHM 0790051R

R0C7 RES.CHIP 1/16W 10K OHM 0790051R

R0C8 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

R0C9 RES.CHIP 1/16W 3.9K OHM 0790045R

R0E2 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R




R0E8 RES.CHIP 1/16W 10K OHM 0790051R

R001 CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

CHIP RESISTOR RECJUMPER-1-16C16T1608 0790001R

RES.CHIP 1/16W 100 OHM 0790024R


RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 1.0K OHM 0790037R









RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM 0790024R


RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM (4 R) AQ00024R




RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 10K OHM 0790051R


RES.CHIP 1/16W 100 OHM 0790024R













74

32PD3000 / 42PD3000

R066 RES.CHIP 1/16W 100 OHM 0790024R

R068 RES.CHIP 1/16W 100 OHM 0790024R



R077 RES.CHIP 1/16W 4.7K OHM 0790046R

R078 RES.CHIP 1/16W 4.7K OHM 0790046R

R079 RES.CHIP 1/16W 33K OHM 0790057R



R083 RES.CHIP 1/16W 100 OHM 0790024R

R084 RES.CHIP 1/16W 1.0K OHM 0790037R

R085 RES.CHIP 1/16W 100 OHM 0790024R

R087 RES.CHIP 1/16W 220 OHM 0790028R

R092 RES.CHIP 1/16W 2.2K OHM 0790042R

R093 RES.CHIP 1/16W 2.2K OHM 0790042R

R094 RES.CHIP 1/16W 4.7K OHM 0790046R

R095 RES.CHIP 1/16W 4.7K OHM 0790046R

R096 RES.CHIP 1/16W 560 OHM 0790034R

R097 RES.CHIP 1/16W 2.2K OHM 0790042R

R098 RES.CHIP 1/16W 1.0K OHM 0790037R

R099 RES.CHIP 1/16W 1.0K OHM 0790037R

R201 RES.CHIP 1/16W 10K OHM 0790051R

R202 RES.CHIP 1/16W 10K OHM 0790051R

R203 RES.CHIP 1/16W 10K OHM 0790051R

R204 RES.CHIP 1/16W 10K OHM 0790051R

R205 RES.CHIP 1/16W 10K OHM 0790051R

R206 RES.CHIP 1/16W 100 OHM 0790024R

R207 RES.CHIP 1/16W 100 OHM 0790024R


R209 RES 2125 CHIP JAMPER WIRE 0195250R

R210 RES 2125 CHIP JAMPER WIRE 0195250R


R213 RES.CHIP 1/16W 10K OHM 0790051R

R217 RES.CHIP 1/16W 1.0K OHM 0790037R

R227 RES.CHIP 1/16W 5.6K OHM 0790047R


R251 RES.CHIP 1/16W 0 OHM AQ00001R



R401 RES.CHIP 1/16W 220 OHM 0790028R

R402 RES.CHIP 1/16W 220 OHM 0790028R

R403 RES.CHIP 1/16W 220K OHM 0790068R

R404 RES.CHIP 1/16W 220K OHM 0790068R

R405 RES.CHIP 1/16W 100 OHM 0790024R

R406 RES.CHIP 1/16W 100 OHM 0790024R

R407 RES.CHIP 1/16W 56K OHM 0790061R

R408 RES.-1608CHIP 1/16W 13K-J TAPE 0196096R


R410 RES 1608 CHIP 1/16W 36KJ TAPE 0196106R

R411 RES.-1608CHIP 1/16W 9.1K-J TAPE 0196091R


R413 RES.CHIP 1/16W 10K OHM 0790051R

R414 RES.-1608CHIP 1/16W 910-J TAPE 0196066R

R414 RES.CHIP 1/16W 820 OHM 0790036R

R415 RES.-1608CHIP 1/16W 910-J TAPE 0196066R

R415 RES.CHIP 1/16W 820 OHM 0790036R

R416 RES.-1608CHIP 1/16W 2.4K-J TAPE 0196077R

R417 RES.CHIP 1/16W 5.6K OHM 0790047R

R418 RES.CHIP 1/16W 1.0K OHM 0790037R

R419 RES.CHIP 1/16W 1.0K OHM 0790037R

R420 RES.CHIP 1/16W 1.0K OHM 0790037R

R421 RES.CHIP 1/16W 6.8K OHM 0790048R

R422 RES.CHIP 1/16W 6.8K OHM 0790048R

R423 RES.CHIP 1/16W 1.0K OHM 0790037R

R424 RES.CHIP 1/16W 1.0K OHM 0790037R

R425 RES.CHIP 1/16W 1.0K OHM 0790037R

R426 RES.CHIP 1/16W 1.0K OHM 0790037R





R431 RESISTOR CARBON FILM SRD1/2P-B 10-J 0113701M

R432 RESISTOR CARBON FILM SRD1/2P-B 10-J 0113701M

R433 RES.CHIP 1/16W 10K OHM 0790051R

R434 RES.CHIP 1/16W 10K OHM 0790051R

R435 RES.CHIP 1/16W 2.2K OHM 0790042R

R436 RES.CHIP 1/16W 100K OHM 0790064R

R437 RES.CHIP 1/16W 100 OHM 0790024R

R438 RES.CHIP 1/16W 47K OHM 0790059R

R439 RES.CHIP 1/16W 8.2K OHM 0790049R



R442 RES.CHIP 1/16W 12K OHM 0790052R

R443 RES.CHIP 1/16W 4.7K OHM 0790046R

R446 RES.CHIP 1/16W 4.7K OHM 0790046R

R447 RES.CHIP 1/16W 4.7K OHM 0790046R

R628

R629

R630

R631

R636

R637

R638

R639

R640

R641

R642

R643

R644

R612

R613

R614

R615

R616

R617

R618

R619

R620

R621

R622

R625

R626

R627

R448

R449

R450

R458

R459

R460

R461

R462

R463

R600

R602

R603

R604

R605

R606

R607

R609

R610






RES.CHIP 1/16W 100 OHM 0790024R





RES.CHIP 1/16W 33 OHM 0790017R




RES.CHIP 1/16W 390 OHM 0790032R















RES.CHIP 1/16W 100 OHM 0790024R

RES.CHIP 1/16W 100 OHM 0790024R














RES.CHIP 1/16W 330 OHM 0790031R

R645

R646

R648

R654

RES.CHIP 1/16W 330 OHM 0790031R



RES.CHIP 1/16W 220 OHM 0790028R

R655

R656

RES.CHIP 1/16W 220 OHM 0790028R


R657 RES.CHIP 1/16W 33K OHM 0790057R

S001 TACT SKHH

XS01 SMD LC FILTER MEA3216L50R0 BE00391R

XS02 3218 CHIP LC FILTER BE00412R

XS03 3218 CHIP LC FILTER BE00412R

X001 SMD LC FILTER MEA3216L50R0 BE00391R

X002 OSCILLATOR (SMD-49) BL00291R

X600 CHIP CERAMIC FILTER NFL21SP506X1C3D

BK00191R


BK00191R


BK00191R


BK00191R


BK00191R


BK00191R

Z002 UNDECIDED

Filter Board

CIR No. DESCRIPTION ECN#[035] P#

# PWB ASS'Y PT3 FILTER JT23651

# "PWA PT3 FILTER(""42"")" JT23652

# PWA

# PWA

# PWA

# PWA PT3

# PWA

# PWA FILTER(W37-PDH1/PDT1)

#01 INLET PWB METAL PT3 NA59591

#02 3*12 SCREW WITH WASHER 4520883

#03 LOCK SPACER ML00702

75

32PD3000 / 42PD3000

PT3

C001 CAP.-ELECTRO. 100UF-M(SMG) 6.3V 0800324R

C002 CAP.-CERAMIC 0.01UF-Z F 50V TAPE 0244171R

C901 ACROSS CAPA 0.47UF 250V RE474 AN01447S



C904 CAP. CERAMIC CS10-B2GA102KYVS AJ00157R

C905 CAP. CERAMIC CS10-B2GA102KYVS AJ00157R


SPR-54MVW

EGND CONNECTOR ED01651R

E902 CONNECTOR EF09584



F901

F902

HT FUSE 250V 6.3A 5.2X20MM FN00439

HT FUSE 250V 6.3A 5.2X20MM FN00439

H001 GP1U281Q CZ00641

SP

JA403 JACK TERMINAL

J901 PLAG-AC INLET SK-1019 2676371

KL911 0.60MM TAPED JUMP.WIRE 2784381M

KL912 0.60MM TAPED JUMP.WIRE 2784381M

KR001 0.60MM TAPED JUMP.WIRE 2784381M

KR002 0.60MM TAPED JUMP.WIRE 2784381M






















L481

L482

DC COM. MODE CHOKE COIL 7UH 2A BZ05521

DC COM. MODE CHOKE COIL 7UH 2A BZ05521

FILTER

L902 LINE FILTER 5MH 5A BZ04602

FILTER

L911 FERRITE BEADS CORE B 2.3UH 2123462M

SPACER

NF901 FUSE HOLDER FP00031R

NF902 FUSE

N001 LED A5WS

N33 PRINTED MATTER QT37872



PPU1 "6P VH CONNECTOR PLUG #2,4,5 NC" ED02812

PPU2 2P PLUG PIN ED02801

PPU3 2P PLUG PIN ED02801

PSC2 PIN POST (PH 6P) 2675285

PSC2 CONNECTOR-6P(PH)

PSW 8P VH PLUG PIN ED02811

R001 RES.-CARBON FLM 1/16W 680-JB 0700038M

R002 RES.-CARBON FLM 1/16W 560-JB 0700037M

R003 RES.-CARBON FLM 1/16W 1.0K-JB 0700041M

R901 RES.MTL GRAZD FLM 1/2W 3.3M AT03672M

R902 RES.MTL GRAZD FLM 1/2W 3.3M AT03672M

ZJ901 ADHESIVE TAPE (SCOTCH NO.3 W=9) 9449503

Z101 TERMINAL PIN EYELET EU00211














Z131

Z202

Z204

Z209

Z211

Z212

Z213

Z214

Z215

Z216

Z218

Z230

Z232

Z234

Z235

Z236

Z237

TERMINAL PIN EYELET EU00211

















32PD3000


# FINAL

# FINAL

ASS'Y

# FINAL

# FINAL W32-PD1 UQ32907

#001W W103330

#002W W111112

#003W W151217

#003W W151222

#004W UNDECIDED

#005W UNDECIDED

#01A BEZEL

0

#01AG BEZEL

32M3000

ASS'Y

#01B BEZEL

32PD1 QD35527

QD35262

#011 BEZEL 32M3000 QD35251

PDP32 QD21492

#012 POW SW BUTTON 32M PC05601

BUTTON

#012SV POW SW BUTON(SV) PC05631

#013 LED LENS 32M3000 PH32171

#013G LAMP PDP32 PH30111

#014 90 KNOB SPRING SUS 3332452

3332452 #014G 90 KNOB SPRING SUS

#015G SP NET 32PD1 PH30064

#015L SP NET 32M3000 L PH32162

#015L SP NET 32A3000 R PH32163

#015R SP NET 32M3000 R PH32161

#015R SP NET 32A3000 PH32164

#016 HITACHI BADE W40 PU00781

#016G HITACHI BADGE PDP32 PU00651


#017G 3*12 SCREW WITH WASHER 4319361

#018 DECO PANEL 32M3000 PH32151

#018C DECO PANEL 32A3000

#018G UNDECIDED

#021 COVER 32M3000 QA02652

PH32152

PDP32H QA02252

#022 ST BRIND LABEL QL22761

#023 AC & EARTH LABEL P32 QL20401

#023AE AC LABEL QL21001

#024 SIGNAL PLATE 32M3000 QL22701

#024A LABEL QL22704

QL22705

#024G SIGNAL PDP32H QL20392

#03 STAND ASS'Y 32-3000 QJ01131

ASS'Y

#030G STAND UPPER PDP32 QD21531

BASE

#032G STAND SLIDER PDP32 NX06971

#033G STAND CAP 32 NJ05251

#034G STAND BASE METAL 32 NQ09881

#035 STAND ASSY 32-MAN QJ01171

#035G 3782951

LEG

#037G 4X12 B TAPPING SCREW STEEL 4519511

#038G SCREW 4*16 B-TAPPING (BLACK) SWRM 4519513

#039G STAND SUPPORT 2200 NQ20042

#041 CENTER FRAME PDP32 NQ22331

#042 FILTER SUPPORT 32A NA52411

#042 FILTER SUPPORT 32A NA59521

#042G FILTER SUPPORT 32A NA52411

#043 FILTER SUPPORT 32B NA52412

#043 FILTER SUPPORT 32B NA59522

#043G FILTER SUPPORT 32B NA52412

#046G FRAME SPACER MTL U NQ22691

#047G FRAME SPACER MTL B NQ22692

76

#0501 MAIN FRAME R M3000 NQ22281

#0505 MAIN FRAME L M3000 NQ22282

#0510 SIDE SHIELD R M3000 MD07951

#0512 SIDE SHIELD L M3000 MD07952

#0521 SIG METAL W32M3000 NA59491

#0531 FILTER MTL 32M3000 NA59511

#0541 AC METAL M3000 NA59481

#0542 AC INLET/SW MTL J NA59482

#0543 LED PWB MTL 32M3000 NA59501

#0544 INLET INSULAT C MN04901

#0545 GR MTL PDP32 MD07021

#0546 W32 INLET INS MN04941

INSULAT

#0548 EDGE COVER 32 MN04911

#0549 INLET HOLD MTL M3000 MK01181

#0550 GASKET MF01051

#0551 BUSHING ML01121

MF01053

#0555 GASKET

#0556 GASKET

#0557 GASKET MF00718

#0558 SW INSULATION 32 MN03591

FILTER

#0560 AIR MN03556

#0561 INLET SHIELD W32 MD08051

#0562 INLET MTL A W32 MD08061

#0564 INLET MTL B W32 MD08071

#0566 W32 INLET COVER A ME03311

#0568 W32 INLET COVER B ME03321

UNIT GM01211

#0611 BUTTON HOLDER HL300 3274061

#0613 POW RELAY BUTTON 32 NJ05371

#0622 WIRE

#0628 BRACKET NJ02902

STOPPER ML01131

#0631 FASTINING

#0632 WIRE

PARTS ML00692

CLAMP

#0636 CABLE

LWS-1316 ML00694

CRAMPER 3705264

#0704 M3*8 SCREW WITH WASHER 4520881

#0705 3*8 CE KNURLED SCREW 4522881






#0712 SCREW 3X16T WITH WA MJ02211

#0712A SCREW 3X16T WITH WA MJ02211



#0715 3*8SEREW WITH WASHER

#0720 6*12 MJ02101

#0721 M5*12 DT SCREW

MJ02781

#0723 SCREW

4520782

M4*84518383

#0724 3PIECES M3 DT SCREW SWCH16A-DA

#0732 BOLT M6X20 WITH WASHER SWRM12A

4527821

#0734 M3*10 SCREW WITH S.W AND R.W 4341291


#0741 3X10 BT SCREW BLACK 8699410

#0742 3X10 BT SCREW BLACK 8699410

#0744 WASHER 8815126

#0745 SCREW 4 * 8 PAN HEAD 8711608

(LOCKING)

#0747 SCREW 4 * 8 PAN HEAD 8711608

#0748 M3*8 SCREW WITH WASHER 4520881

#0760 NITTO TAPE NO.5 W25 (BLACK) 9449538

#0770 NITTO TAPE NO.5 W20 (BLACK) 9449545

#0775 MARK

#0790 SCREW 6 ANGLE FOR D SUB MJ01195

#0800 OTHER OPTICAL PARTS KS04891



#30 GRIP JOINT MM00182

A FPF32C106128UA-61 DD00453

32V(H2)

A011 PSA PT3 SIGNAL/AUDIO JP06091

A011L LJP0609

A012 PSA PT3 SIGNAL/AUDIO JP06093

A012L LJP0609

A021 PWB ASS'Y PT3 FILTER JT23651

A021L LJT2365

A022 "PWA PT3 FILTER(""42"")" JT23652

A022L LJT2365

PT3

A023L LJT2365

32PD3000 / 42PD3000

EAS1 CONNECTOR EF21353

EAS2 CONNECTOR EF21363

ECN64 CONNECTOR EF21623




CO-06C-C2R0-111#2,5N" EF21631

ECN69 FLEXIBLE FLAT WIRE EK01491

EDS CONNECTOR CO-20C-C1R2S171-DF13 EF21671

EDS CONNECTOR EF21673

EPA CONN. W/WIRE SEH 4J L330(C-C) 2973734S

EPS 9P EH CONNE L=220 2973879S

EPU1 CONNECTOR EF22381


ESC2 CONNECTOR CO-06C-C2R0-621PH UL EF21331

ESS 1.5MM PITCH 13P FG CONNECTOR L=180MM EF22291

ESU CONNECTOR EF21386

ESW CONNECTOR EF21395


E901 JACK EP00241

E901 RECEPTACLE EP00261

E901A UL-TUBE NO.9/16 INCH CLEAR 9451119

E901A UL FR-1 TUBE NO.3 9451138

E901B SK

E901C UL-TUBE NO.9/16 INCH CLEAR 9451119

E901C UL FR-1 TUBE NO.3 9451138

E902 CONNECTOR



E906 2990787

NDS CLAMP NOISE FILTER ZCAT3035 2169512

LX-ZCAT2032 2169513

LX-ZCAT1518 2169511

NPS COIL LX-ZCAT2032 2169513

LX-ZCAT2032 2169513

N906 COIL

S900

S900A SK

2169511

POWER SWITCH SDDFC3002A 2634733

BINDER 3763751

S900B UL FR-1 TUBE NO.3 9451138

U1 POWER UNIT MPF7103 HA01121

42PD3000


# FINAL

# FINAL

# FINAL

# FINAL PD42-A3000-751

#01W W103330

#02W W111112

#03W W151215

#03W UNDECIDED



#090 PT3 F/FRAME ASS'Y 42 QD34902

#091 F/FRAME ASSY 42PD3000 QD34903

#095 PT3 FRONT FRAME 42QD34782

#097 PT3 DECO PANEL 42 PH32011

#097 PT3 DECO PANEL 42E PH32012

#098 PT3 RC LENS 42 PC05481

#099 HITACHI BADGE PD42 PU00723

#100 3X10 BT SCREW BLACK 8699410 8699410

#104L FILTER FIX MTL R 42PT3 NA54123

#104R FILTER FIX MTL L 42PT3 NA54124

#105 FILTER FIX MTL U 42PT3 NA54223

#106 FILTER FIX MTL B 42PT3 NA54232

#107 4X12 3P??? ????? TNE MJ02743

#107 4X12 B TAPPING SCREW STEEL 4519511

#108 GASKET 3-4-982 MF00714

#109 GASKET 3-4-593 MF00715

#110 GASKET TCS 6-0.7-584

#110A GASKET TCS 6-0.7-584

#111 GASKET TCS 6-0.7-964

#111A GASKET TCS 6-0.7-964

MF00914

MF00914

MF00915

MF00915

#112 AIR FILTER A PDP42 MN03553

#113 AIR FILTER 10-4-579 MN03554

#116 HIMERON 15-12-0.8 MS00793

#120 PT3 FILTER S MTL 42 NA58773

#121 PT3 FILTER MTL UB 42 NA58781

#122 PT3 FILTER MTL B 42 NA58782

#191 BACK COVER ASSY W42M3000 QA02604

#192 BACK COVER ASSY 42PD3000 QA02605

#193 BACK COVER ASSY PD42A3000 QA02606

#201 BACK COVER W42M3000 QA02503

#202 SIGNAL LABEL 42PT3 QL22471

#202 SIGNAL LABEL 42PT3E QL22472

#202 SIGNAL LABEL 42PT3A QL22473

77

32PD3000 / 42PD3000

#204 SPEAKER TERMINAL LABEL W42-PDH2100 QL21191

#204 SPEAKER LABEL CL42 QL21193

#205 GRIP PD2100 PH31101

#210 TEMP CAUTION LABEL QL21401

#210 TEMP CAUTION LABEL QL21402

#212 AC & EARTH LABEL P32 QL20401

#212 AC LABEL QL21001

#214 4198577

#215 CABLE CRAMPER 3705264

#216 M4X10 AL-TAP SCREW MJ02671

#220 ST BRIND LABEL QL22761


#300 STAND ASS'Y 3000 QJ01101

#300 STAND ASSY 42-MAN QJ01191

#402 MAIN FRAME 42PT3 QA02436

#404 INS LABEL 42PT3 QL06163

#410 AC INLET METAL P4121 QA02521

#410 AC INLET COVER PD1 QA02522

#411 AC INLET COVER B QA02551

#413 INLET INSLATOR PT3 ME03281

#418 FASTINING PARTS ML00861

#420 VIDEO COVER MTL 42PT3 NA54164

#421 PT3 SIGNAL PWB MTL 42 NA59221

#422 PCB SUPPORT 4SPA 3782718

#441 SIGNAL METAL P4121 NA54181

#451 POW BUTTON PANEL PT2 PH31141

#452 POWER BUTTON PT2 PC05361

#453 AC SW METAL PT2 NA54081

#481 SP TERM METAL P42 NA54131

#481A SP SHIELD 42PT2 MD07331

#481B SP SPACER 42PT2 MS00731

#482 EDGE SADDLE 0505 ML01051

#491 POW SHIELD SHEET (2) MF00752

#491A M3X8 AL-TAP SCREW MJ02661

#491B SPONGE CUSHION 10*10*245 MN04181

#492 FILTER INS UP PD1A MN05031

#492A M3X8 AL-TAP SCREW MJ02661

#502 FILTER PWB INS 42PT3 ME03042

#601 FASTINING PARTS ML00692

#604 BUSHING ML01121

#616 PWB STOPPER ML01131

#617 LEAD CLAMP 3731214

#620 PWB STOPPER 12S ML01134

#690 EARTH MARK LABEL QL21311

#690A EARTH LABEL



#704A M3*10 SCREW WITH S.W AND R.W 4341291


#707 3X10 BT SCREW BLACK 8699410 8699410

#708 M3 SCREW WITH WASHER 4520882

#709 M3*10 SCREW WITH S.W AND R.W 4341291






#732 M3X12 SCREW 3P W B MJ00926



#751 4X10 SCREW WITH WASHER MJ02721

#751A WASHER 8815126


(LOCKING)


#761 M5*12 DT SCREW 4520782

#764 3X10 BT SCREW BLACK 8699410 8699410

#765 SCREW 6 ANGLE FOR D SUB MJ01195

#767 4X16 3P??? ????? TNE MJ02744

#767 4X16 D TAPPING SCREW SWCH16A 4520232


#790 M6X30 BOLT WITH WASHER SWRM12A

#801 GRIP JOINT MM00182

42V(H2)

A11 "PSA PT3 SIGNAL/AUDIO FOR ""42"

4527823

JP06092

A11L LJP0609

A21 PWA PT3 FILTER(JP.42) JT23655

A21L LJT2365

A22 PWA PT3 FILTER JT23656

A22L LJT2365

EAS1 2J L=820

EAS2 2973709S

EDS CONNECTOR CO-20C-C1R2-101DF13C EF21343

EJ201 WIRE

EJ202 CONNECTOR EF21622

EJ203 CONNECTOR EF21612

78

CO-07C-C2R0-511#236N EF21644

EJ206 "CONNECTOR

EPA 2973733S

CO-07C-C2R0-301#236N EF21643

EJ205 CONNECTOR

EPS 2973878S



ESC2 CONNECTOR CO-06C-C2R0-681PH UL EF21332

ESS 1.5MM PITCH 13P FG CONNECTOR L=180MM EF22291

ESU CONNECTOR EF21385

ESW CONNECTOR

E1 CONNECTOR

CO-08C-N3R9-241#2357 EF21391

EF21371

E901 JACK EP00241

E901A UL FR-1 TUBE NO.3 9451138

BINDER 3763751

E901C UL FR-1 TUBE NO.3 9451138

CO-01T-N0R0-111 EF09605


NDS COIL LX-ZCAT2032 2169513

NP02 PURSE

S900

NYLON

POWER SWITCH SDDFC3002A 2634733

S900A SK

S900B UL FR-1 TUBE NO.3 9451138

U1 POWER UNIT(W37/W42) HA01131

U1 POW-UNIT MPF7404 TV HA01133

No ITEM

1 CVBS &

S.INPUT

SOFTER

POTENTIAL PROBLEM/QUESTION

CVBS and S-VHS input is softer than

CL32PD2100 (with NR=off).

When DVD signal input through AV1, Front by

CVBS or S-VHS, picture is soft.

2 BLACK LEVEL

BRIGHT (Black level set- up)

CVBS and S-output from DVD player has set up voltage of black level around 0.1V.

This causes black brighter and loose contrast.

This was found with DVD player DV P305 with

Spanish DVD disc. I have never found the same phenomenon in any other places so far. In HEL, I have checked DV P305 with UK DVD disc and confirmed OK (no set up voltage) In Italy, this was not found with DVD player DV P250 with

Italy DVD disc. CVBS and S-input from DVD

3 LTI EFFECT

Luminance

Transient

Improvement

PICTURE > MORE > LTI

LTI effect is not significant in CVBS and S-

INPUT but very significant on RGB and component input.

CAUSE and COUNTERMEASURE/ADVICE

CAUSE ;

DVD output signal includes noise equivalent to picture frequency.

CL32PD2100 displays a picture more detail with NR=off than 32PD3000 but DVD noise is also emphasized especially seeing sky, you can see dot noise on

CL32PD2100.

32PD3000 is filtered noise so you cannot see noise but a picture is also becoming softer.

ADVICE;

CVBS and S-input is not good for demonstration. Because almost all DVD has RGB, please use RGB for demo or

YCbCr/YpbPr instead (new feature) RGB input of 32PD3000 is more crisp and less noise than CL32PD2100.

The set up black level is not expected on PAL signal. So something wrong probably when DVD disc is copied in

Spanish DVD software company. Or Some DVD player may have potential cause of this problem. But it is recommended that the demonstration should be done by RGB or component input to avoid this phenomenon. Almost all DVD players have RGB output.

NOTE

CL32PD2100 has LTI but it is so strong that noise is also emphasised very much. On 32PD3000, this is improved to effect clear signal avoiding noise enhancement.

This is observed only in Spain.

This is caused by DVD player option. DV

P305 has menu option to switch SET UP >

DISPLAY OPTION >

BLACK LEVEL =

On/Off. When it is set to On, the signal on left hand drawing is output from DVD.

4 NOISE

REDUCTION

EFFECT

PICTURE > MORE > YNR

PICTURE > MORE > CNR

Noise reduction effect is not as strong as

CL32PD2100. CL32PD2100 is too strong to give crisp picture. Instead, there are 2 types Noise

Sometime on TV, noise appears close to colour frequency.

By previous noise reduction, when this noise is reduced by

NR feature, it affect luminance causing loose of picture sharpness. CNR only reduce this noise without affecting picture sharpness.

79

No ITEM

5 WHITE

BALANCE

6 CLOCK NOISE

ON SOUND

7 RGB MODE

STREAK

NOISE


Reduction on 32PD3000. YNR and CNR. YNR ;

Luminance noise is reduced without affecting

Chrominane transient. CNR ; Chrominace noise is reduced without loosing sharpness of picture

(Luminance)

WHITE BALANCE adjustment is done by menu bar. COOL/NORMAL/WARM selection is also possible but in service menu. In Picture mode is selected as shown below. DYNAMIC ; COOL

NATURAL ; COOL

CINEMA ; NORMAL

FAVOURITE ; COOL

When selecting CENTRE speaker or AV4 mode, you can hear clock noise in sound when volume level is increased more than half. This is caused by cross-talk in the cable. AV4 sound and centre sound are located after audio decoder (MSP3410) which leads audio input impedance

When you see streak noise on RGB input, this is caused by clamping error accidentally.


White balance adjustment in menu bar ranges from 6500K to

11000K in DYNAMIC/NATURAL/FAVOURITE. In

CINEMA, colour temperature range is shifted to warm side.

Screened interface cable cures this problem.

In service mode, check SVC > OPT > RGB Comb = off

NOTE

It will be applied after trail 100 Q’ty. For 100,

DMD send HEL improved one.

8 MENU

WIDEMODE

9 PC WINDOW

LIMITATION

When you select MENU, picture wide mode is changed to WIDESCREEN wherever wide mode is.

This is because OSD is inserted BEFORE a picture is scaled to any of wide modes. If a picture is zoomed to LETTER

BOX or T16:9L, some of the menu is hidden if wide mode remains as it is. This system gets TV+TEXT feature possible.

When selecting PC window, sub picture is displayed. Sub picture is not possible to display

YPbPr and PC so those are prohibited to be selected.

By AV key selection, AV4 and PC is skipped. AV/PC in position, FRONT is displayed when selecting the position where AV4 and PC is stored. In case of AV in position ideally that psotion should be skipped. But it is not easy for software to carry out so FRONT is selected as alternative to blanking.

80

No ITEM

10 PICTURE

MODE

11 AUDIO MODE Audio mode provides 4 kinds of modes.

12 TRUBASS &

MATRIX

SURROUND

13 AV4

Components

INPUT

14 TV + TEXT


Picture mode provides 4 kinds of modes.

DYNAMIC, NATURAL, CINEMA,

FAVOURITE

MUSIC, SPEECH, CINEMA, FAVOURITE

The effect is the same as PDP1st generation. But operation is a little different.

AV4 supports 4 types of components inputs.

Normal 50Hz (PAL) ; YCbCb50

Normal 60Nz (NTSC) ; YCbCr60

Progressive 50Hz (PAL) ; YPbPr50

Progressive 60Hz (NTSC) ; YPbPr60

In TV+TEXT, R/C operation follows

TELETEXT operation. Ten keys select page number not a position number.


We recommend

DYNAMIC ; DVD for DEMO

NATURAL ; TV, VCR, STB

CINEMA ; DVD, STB

FAVOURITE ; TV, VCR, DVD, STB

Only selecting FAVOURITE allows a user to adjust

CONTRAST, BRIGHTNESS, etc.

We recommend

MUSIC ; MUSIC

SPEECH ; NEWS, TALK SHOW

CINEMA ; MOVIE, DRAMA

FAVOURITE ; any of those and adjust to users’ preference.

Only selecting FAVOURITE allows a user to adjust

TREBLE, BASS, TruBASS, etc

TruBass/Matrix are adjusted in each audio mode when selected as follows;

MUSIC ; TruBASS=HIGH, MATRIX=ON

SPEECH ; TruBASS=OFF, MATRIX=OFF

CINEMA ; TruBASS=MID, MATRIX=ON

Those can be changed in service menu.

FAVOURITE ; according to user menu. Shipping is

TruBASS=LOW, MTRIX=OFF

However, MATRIX can be switched on and off by surround key in each audio modes after that.

When you select AV4, input signal is automatically identified to display properly on screen.

NOTE

As operation, [A|B] key is switched to TV+TEXT on and off.

From TELETEXT mode, it switches TV+TEXT $

TEXT $ TV+TEXT ….

From TV mode, it switches TV+TEXT $ TV $

TV+TEXT ….

In TV+TEXT, menu is not available to adjust picture and any other menu items. (In TEXT mode, the same thing happens.)

81

Hitachi, Ltd. Tokyo, Japan

International Sales Division

THE HITACHI ATAGO BUILDING,

No. 15 –12 Nishi Shinbashi, 2 – Chome,

Minato – Ku, Tokyo 105-8430, Japan.

Tel: 03 35022111

HITACHI EUROPE LTD.

Dukes Meadow

Millboard Road

HITACHI EUROPE S.A.

364, Kifissias Ave. & 1, Delfon Str.

152 33 Chalandri

Bourne End

Buckinghamshire

Athens

GREECE

SL8 5XF Tel: 1-6837200

UNITED KINGDOM Fax: 1-6835694

Tel: 01628 643000 Email: [email protected]

Fax: 01628 643400

Email: [email protected]

HITACHI EUROPE GmbH

Munich Office

Dornacher Strasse 3

D-85622 Feldkirchen bei München

HITACHI EUROPE S.A.

Gran Via Carlos III, 101 - 1

08028 Barcelona

SPAIN

GERMANY

Tel: +49 -89-991 80-0

Tel: 93 409 2550

Fax: 93 491 3513

Fax: +49 - 89 - 991 80 -224 Email: [email protected]

Hotline: +49 - 180 - 551 25 51 (12ct/min.)


HITACHI EUROPE SRL

Via T. Gulli n.39

20147 MILAN

HITACHI EUROPE AB

Box 77

S-164 94 KISTA

SWEDEN

Tel: 08 562 711 00

ITALY

Tel: 02 487861

Fax: 02 48786381

Fax: 08 562 711 11


Servizio Clienti

Tel. 02 38073415


HITACHI EUROPE S.A.S

Lyon Office

B.P. 45, 69671 Bron Cedex

FRANCE

Tel: 04 72 14 29 70

NORWAY

Tel: 02205 9060

Fax: 04 72 14 29 99 Fax: 02205 9061

Email: [email protected] Email [email protected]

ITEM N.V./S.A. (INTERNATIONAL TRADE FOR

ELECTRONIC MATERIAL & MEDIA N.V./S.A)

UCO Tower – Bellevue, 17

B – 9050 GENT

BELGIUM (for BENELUX)

Tel: 09 230 48 01

Fax: 09 230 96 80

HITACHI EUROPE LTD.

Norwegian Branch Office

Strandveien 18

1366 Dysaker


www.hitachi-consumer-eu.com

SM003

October 2002

SM003 32PD3000E 42PD3000E SERVICE MANUAL

SM003

SERVICE MANUAL

MANUEL D'ENTRETIEN

WARTUNGSHANDBUCH

CAUTION:

ATTENTION:

VORSICHT:

Plasma TV

October 2002

Safety

ENGLISH

SAFETY PRECAUTIONS

WARNING: The following precautions must be

ALL PRODUCTS

CE MARK

PICTURE TUBE

LASERS

FRANÇAIS

CONSIGNES DE SECURITE

AVERTISSEMENT: vous devez respecter les

LABEL CE

PICTURE TUBE

RAYONS LASER

DEUTSCH

SICHERHEITSVORKEHRUNGEN

WARNUNG: Die folgenden Vorkehrungen müssen

CE KENNZEICHEN

BILDRÖHRE

LASER

Contents

Lead Free Solder

Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free

• Lead free solder indicator

• Properties of lead free solder

When servicing solder

• Precautions when using leaded solder o

o

When servicing soldering iron

Recommended soldering iron:

Recommended temperature range per part:

Soldering Part

PCB with surface mount devices

Soldering iron temperature

320 °C ±30 °C

PCB without surface mount devices

Chassis, metallic shield, etc.

380 °C ±30 °C

420 °C ±30 °C

PCBs which use lead free solder

• FC4PDP board (AVC block)

• SIGNAL/SOUND board (MONITOR block)

• SP terminal L/R board, FILTER board, LED board (MONITOR block)

Specifications

Item Spec

32PD3000 (PDP;32PD3000E+AVC;AV3000E) 42PD3000 (PDP;42PD3000E+AVC;AV3000E)

;

852x1024 resolution,

1024x1024 resolution,

Advanced progressive & 1024 interlace, Which materializes detailed picture without flicker

TruBass by SRS,

Thin (9cm) and light,

Swivel stand attached monitor, Which is possible to swivel at 30deg toward left and right.

3 Scarts connectors plus front AV input, Which can be connected with DVD, Set Top Box, VCR and

1 Component input,

PC input connection,

Service Data

Block Diagrams

AVC to PDP Block Diagram

AVC Block Diagram

AVC Power Block Diagram

Major Connectors

Schematic Drawing Descriptions

Schematic Page 1 ; Tuner / Video Chroma

* IF demodulator and video chroma

* video switch

Schematic Page 2 ; Sound / AV3 Control

Schematic Page 3 ; Interface Board (component input, progressive sync separation, centre audio channel

Schematic Page 4 ; Power Circuit (Voltage Regulator) / Level Shifter

Power supply connector PSP from Power Supply board