advertisement
Comdial ExecuTech System 2000 LCD User’s Guide
Contents:
•
Answering Calls
•
Making Calls
•
Conference Calls
•
Holding and Parking Calls
•
Call Transferring
•
Call Forwarding
•
Messaging
•
Programming and Preferences
•
Paging
•
Feature Dialing Code Numbering
Plan
•
Speed Dial Index
Answering Calls
Outside Calls
Press the line key with the flashing light and lift the handset. If prime line is configured and ringing or if ringing line preference is enabled, do not press the line key.
Intercom Calls
For voice calls (when caller’s voice is the first thing you hear), speak toward telephone. Lift handset to continue the conversation with privacy if desired.
For tone calls (when the call is announced by a tone rather than the caller’s voice), lift the handset to speak.
Calls Ringing on Another Telephone
•
Lift the handset.
•
Press “ITCM”
•
Dial “*4”
•
Dial the extension number of the ringing telephone.
Calls Ringing within your Group
•
Lift the handset.
•
Press “ITCM”
•
Dial “#4”.
Handsfree Answerback (HFAB)
When a station is busy, an off-hook voice announcement may be received by that station as a secure or non-secure voice announcement (SOHVA or OHVA). An OHVA is transmitted though the speaker of a paired console or the station of certain model Keysets. A SOHVA announcement transmits only through the handset receiver of certain model multilane keysets.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 1 of 14
Respond to OHVA
At five quick tone bursts, speak toward the microphone opening in your station’s console. The outside party will hear the original announcement, but may be prevented from hearing the response if you press and hold the MUTE key.
Respond to SOHVA
At five quick tone bursts and announcement, either,
Comdial 6614T-FB
•
Respond verbally by pressing and holding the mute key and speaking in to the handset.
•
Respond via softkey message by pressing the programmed softkey to display a message to the announcing station and to disconnect that station.
Making Calls
Outside Line Calls
•
Press line key to select. (If prime line feature is enabled, your station will select a line when the handset is lifted).
•
At dial tone, dial the number.
•
Lift handset to converse.
•
Hang up to disconnect.
Comdial 6620E-PG
Trunk Group Access (if enabled)
•
Press “ITCM”
•
Dial the trunk group access code o
9 = main trunk group o
81 = secondary trunk group 1
• o
82 = secondary trunk group 2 o
83 = secondary trunk group 3
At dial tone, dial the number.
Trunk Group Queuing
If all trunks are busy, enter the queue to await the next available.
•
•
Press “ITCM”
Dial trunk group access code (see above)
•
•
At busy tone, dial “*8” and hand up. Station will ring when the trunk group is free.
Lift handset and place call at dial tone.
To Cancel Group Queuing
•
Press “ITCM”
•
Dial “#8”
•
Hang up .
Intercom Calling
Voice Calling
•
Lift handset.
•
Press “ITCM”
•
Dial extension number (“0”) to reach the system operator.
•
Speak to called agent.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 2 of 14
Voice Call a DSS Number
•
Lift handset.
•
Press desired softkey.
•
Speak to called agent.
Tone Calling
If the system is programmed for tone signal as the first option, pressing “ITCM” a second time is not necessary.
•
Lift handset.
•
Press “ITCM”.
•
Dial the extension number.
•
Press “ITCM” again. Called station will ring.
Tone Call a DSS Number
•
Lift handset.
•
Press softkey pre-programmed for the desired station
•
Press “ITCM”.
•
When the party answers, respond as usual.
Make an OHVA Call
Places a voice announcement on another station that is off-hook or busy on a call.
•
Make intercom call.
•
At five quick tone bursts, make announcement. If a busy tone sounds, OHVA is not available.
•
Wait for reply. If your station is an LCD speakerphone, the called agent may send a nonverbal reply to your display. When the message is displayed, the station is disconnected.
OHVA or SOHVA?
Intercom announcements may be received as on off-hook voice announcement (OHVA) or a secure off-hook voice announcement (SOHVA). The method is dependent upon the class of service programming and type of equipment being used at the called station.
Speed Dialing
To dial station speed dial numbers:
•
Consult your speed dial directory (see printable index card on page 14 of this document).
•
Dial 0-9 for a personal speed dial number
Dial station speed dial numbers when listening to the dial tone
•
•
Press “HOLD”
Dial 0-9.
Comdial 6714X-PG
Dial system speed dial numbers
•
Consult your speed dial directory (see printable index card on page 14 of this document).
•
Press “*”.
•
Dial the memory location (01-99) for the desired system speed dial number.
Dial system speed dial numbers while listening to dial tone
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 3 of 14
•
Press “HOLD”
•
Dial “*” and the system speed dial location (01-99).
Automatic Dialing / Saved Number Dialing
To automatically dial numbers, press the softkey with the programmed number. If the softkey is programmed on second level, under DSS key, press “HOLD” and the desired softkey.
Automatic Redial
•
Press the pre-programmed auto redial key.
•
The system will dial the number once a minute until the call is answered, or ten minutes have passed.
•
Lift the handset to answer.
If the called station is busy, press auto redial softkey to restart redial cycle.
To cancel automatic redial, pres the auto redial key, lift and replace the handset or press any station key. Any other calls made will cancel auto redial.
Automatic System Call-Back
To have the system call you when a busy telephone on the system becomes idle,
•
Make an intercom call.
•
At the busy signal, dial “*6”
•
Hang up. When the desired extension becomes idle, the calling telephone receives five tone bursts.
To answer callback rings, lift the handset. The called telephone will ring.
To cancel auto call back before it rings,
•
Press “ITCM”
•
Dial “#6”
•
Hang up.
Last Number Redial
•
Press “#” or “HOLD” and “#” if listening to dial tone.
•
Listen for ringing or busy tone.
•
Comdial 6614S-FB
If the party answers, pick up handset to continue. If the line is busy, press “SPKR” to disconnect.
•
Saved Number Redial
Up to 16 digits of the last manually dialed number can be saved for future redial
To save, press the pre-programmed key. To dial, lift handset. At dial tone, press “HOLD” and the pre-programmed softkey.
Speakerphone Operation
To place a call using your speakerphone,
•
Press line or “ITCM”
•
Dial number or press softkey
•
When party answers, speak toward the telephone.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 4 of 14
To answer a call, press line key and speak toward the telephone.
To end a call, press “SPKR”.
To switch from speakerphone to handset, lift the handset.
To switch from handset to speakerphone, press “SPKR” and hang up.
Adjust Dual Tone Multiple Frequency
Some answering machines, banking computers, etc, require that DTMF tones be longer than the standard 80 msec. in length.
Extend the tone length
•
Lift handset or press speaker.
•
Press line key if not automatically selected.
•
Wait 10 seconds, then dial the number and the system will generate long DTMF dial tones.
Conference Calls
Multiline Conference
To set up a call with one internal and two external parties,
•
Establish the first outside call.
•
Press “TRANS/CONF”.
•
Establish second outside call.
•
Press “TRANS/CONF”.
If one party hangs up, the call remains connected. To drop out of an established conference, dial “#” and hand up.
To set up a call with one external and 2 internal parties,
Comdial 6614E-FB
•
Establish outside call.
•
Press “TRANS/CONF”.
•
Dial extension number of the other internal party.
•
When the party answers by pressing intercom or lifting the handset, press “TRANS/CONF”.
To set up a call with three internal parties,
•
Establish first call.
•
Press “TRANS/CONF”
•
Establish second call.
•
Press “TRANS/CONF” to establish the conference.
Holding and Parking Calls
To place a call on hold,
•
Press Hold
Exclusive Hold
To place a call on hold for your exclusive retrieval, press “HOLD”.
To answer the call, press the line key with the flashing light or press “HOLD”
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 5 of 14
Hold Recall
A call placed on hold will automatically ring back to the telephone that placed it on hold. If the call was placed on exclusive hold, it will revert to manual hold after the hold recall time period and can then be answered by any agent.
Direct Station Hold
To park a call to a station
•
While on a call, press “ITCM”
•
Dial “*90” and the extension number to receive the parked call.
To retrieve a held call, dial “#90” from the receiving extension.
To cancel a direct station hold, dial “*4” and the extension number of the holding station.
Call Park
To park a call in one of nine orbits,
•
Press “ITCM” while on a call.
•
Dial “*”.
•
Dial a park zone access code (91-99)
Retrieve a parked call,
•
Press “ITCM” from any station.
•
Dial “#”.
•
Dial the park zone (91-99).
Comdial 6600E-AB
Call Transferring
Screened Transfer
•
Answer an outside call.
•
Press TRANS/CONF.
•
Dial the extension number of the party to be transferred to or press the DSS key or one-key intercom calling.
•
•
When intercom party answers, announce the call and press “TAP” then hang up.
If the called party is busy or does not answer, press TRANS/CONF to retrieve the call.
Unscreened Call Transfer
•
Answer an outside call.
•
Press TRANS/CONF
•
Dial the extension number of the party to receive the call or press DSS key for one-key intercom calling
•
Hang up handset.
Answer Transferred call Recall
•
Press “TRANS/CONF”
Call Forwarding
When forwarded calls ring on the receiving station, a short tone burst will sound to remind the agent that calls are being forwarded.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 6 of 14
To send all calls to another station,
•
Press “ITCM”
•
Dial “*5”
•
Dial the extension number of the station to receive calls.
•
Press “ITCM” and dial “#5” to cancel.
To send intercom and prime line calls to another telephone,
•
Press “ITCM”
•
Dial “*05”
•
Dial the extension number of the station to receive calls.
•
Press “ITCM” and dial “#05” to cancel.
Messaging
The attendant station or central message desk can activate the message waiting light at any telephone to alert the user to a message waiting.
To turn on MW light,
•
Press “ITCM”.
•
Dial “*3”.
•
Dial the extension number of the station to be alerted.
Comdial 6414-PG
To cancel MW light,
•
Press “ITCM”.
•
Dial “#3”.
•
Dial the extension number of the station that was alerted.
To turn off the MW light while delivering the message, press “ITCM”.
To respond to the message waiting alert, observe the display.
Wed 15 13:51
CallXXXX
Where XXXX = the name of the party leaving the message.
•
Lift the handset.
•
Press “ITCM” and “HOLD”.
•
Connection to the message desk is established.
LCD Messaging
Pre-programmed messages can be set at a station to be displayed on a calling
LCD speakerphone. This informs the calling station of the called agent’s location and estimated return time.
To turn on message,
•
Press “ITCM”
•
Dial “*02”.
•
Reference the message list.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 7 of 14
•
Dial the message code number (0-9)
At this point you may be able to further customize certain messages. For example, when using the
“Back At” or “Call” message, enter the return time or number where you may be reached after selecting the message.
To turn off message,
•
Press “ITCM”
•
Dial “#02”
Station-to-Station Messaging
When a station you wish to reach is busy or rings without answer, you may request the party return your call using station-to-station messaging.
To use messaging,
•
Place call.
•
At ring-back tone, dial “*7”. The BLF light at the called station lights.
If the called station does not have busy lamp appearance of the calling station, the calling station is transferred to the central message desk to manually take the message and light the messagewaiting lamp.
To cancel messaging,
•
Press “ITCM”
•
Dial “#7”
•
Dial the extension number of the station at which the message-waiting alert was placed.
•
Hang up.
To answer a message left on your station, press the DSS button associated with the illuminated BLF light.
Comdial Card M0412
Programming and Preferences
Note: For all programming, be sure to label buttons as you enter programming.
Autodial Programming
Autodial numbers can be programmed at any softkey locations that do not have a line assigned to them. They can also be programmed as a secondary function at every DSS memory location.
When programming an autodial number, have in mind over which line the call must be made as well as the digits which must be dialed.
To Program,
•
Press “ITCM”
•
Dial “**1”.
•
Press the desired softkey. If the desired softkey is assigned as DSS/BLF, press “SHFT” and the softkey.
•
•
•
Press the specific line key or keypad 1-4 for trunk group.
Dial the number to be stored. Enter up to 16 digits including 0-9, “*” and “#”.
Press “HOLD” for a pause, “TAP” for a hookflash.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 8 of 14
To Program another number,
•
Press “TRAN/CONF”.
•
Press the next softkey
•
Make line pre-selection if desired.
•
Dial the number to be stored.
•
Press “SPKR” to end.
Station Speed Dial Programming
Storage locations are digits 0-9. To program,
•
Press “ITCM” ”*” ”*” ”2”.
•
Dial a memory location (0-9).
•
Select the line or keypad 1-4 for trunk groups. Options are: o
Specific line key
• o
Keypad 1 for Trunk Group 1 o
Keypad 2 for Trunk Group 2 o
Keypad 3 for Trunk Group 3 o
Keypad 4 for Trunk Group 4 o
Keypad 0 for prime line or last line used o
ITCM for feature access
Dial the number to be stored. Enter up to 16 digits including 0-9, “*” and “#”.
•
Dial “HOLD” to store a pause or “TAP” to store a hookflash.
•
Example: To store a telephone number (800 362-6740) under location
“0” dial, ITCM **20 Line Key 18003626740.
•
Press “SPKR” to end stations speed dial programming.
Direct Station Selection Busy Lamp Field ( DSS / BLF ) Programming
One-key intercom calling with visual indication of telephone status can be programmed at softkeys not already assigned to lines.
To program DSS,
•
Press “ITCM”
•
Dial “**3”
•
Press softkey to be programmed.
•
Dial the extension number.
•
Repeat the last two steps for additional numbers.
•
Press “SPKR” to end.
Comdial 6706X-FB
Programming Automatic Redial Key
This feature allows the last number dialed to be automatically redialed one a minute for ten minutes. To program a softkey for auto redial,
•
Press “ITCM”
•
Dial “**1”
•
Press desired softkey
•
Press “#”
•
Press “SPKR”.
Programming Secure Off-Hook Voice Announce Key
To assign a softkey for non-verbal one-key response,
•
•
Dial “**1”.
Press softkey desired.
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 9 of 14
•
Dial “5”.
•
Dial a message location (0-9).
•
Press “SPKR” to end.
Ringer Volume
Set the ringer control lever to OFF, LOW or HIGH.
Display Intensity
The brightness and contras of the display can be adjusted any time the phone is idle and on-hook.
To adjust,
•
Press and hold the “MUTE” key. The adjusting cycle begins in about 5 seconds.
•
Release the “MUTE” key when the intensity is at the desired level.
Background Music – Where supplied
Background music turns off automatically when a call is in progress.
To turn music on,
•
Press “ITCM”
•
Dial “*1”
•
Adjust volume with call monitor speaker volume controls.
•
Press “ITCM” and dial “#1” to cancel.
Do Not Disturb
To silence ringing and appear busy to internal callers,
Comdial 6614E-PG
•
•
Press programmed softkey
Press again to cancel
Mute
•
Press and hold “MUTE”
•
Press “MUTE” again to cancel
•
Press and latch “MUTE” to prevent handsfree answer of intercom calls
•
Press and release “MUTE” to enable handsfree answer.
Call Waiting
To activate,
•
When you hear a busy signal when trying to reach an internal extension, dial “*01”.
•
Remain on the line for station to respond.
To cancel, hang up
To answer,
•
When you are on a call and hear a short tone burst in the handset receiver, complete the first call and hang up. Waiting call will begin ringing.
•
Lift handset to answer.
Personal Ring Tones
Select one of four tones for your station ring signal. To select,
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 10 of 14
•
Press “ITCM”
•
Dial “**4”
•
Dial 1, 2, 3 or 4.
Voice Announce Blocking
Voice announce blocking prevents voice signaled intercom calls and paging announcements from coming over the station speaker.
To block,
•
Press “ITCM”.
•
Dial “*2”.
To un-block voice calls,
•
Press “ITCM”
•
Dial “#2”.
Paging
Requires an external paging unit. To page,
All-Call and Zone Paging
To use,
•
Lift handset.
•
Press “ITCM”
•
Dial zone number “84”, “85”, “86”, or “87” for all-call.
•
Make announcement and stay on the line if awaiting an answerback.
•
Hang up handset.
•
Lift the handset.
•
Press the line key for paging or press the programmed softkey.
•
Make announcement.
•
Hang up.
Meet-Me Page
All-call or zone pages can be answered from any station in the system. To answer,
•
Lift the handset of the nearest station.
•
Press “ITCM”
•
Dial “88”.
Identifying a Comdial ExecuTech Telephone*:
Comdial 6414-AB Comdial 6414-BB Comdial 6414-PG
Comdial 6414L-AB
Comdial 6414S-AB
Comdial 6414L-BB Comdial 6414L-PG
Comdial 6414S-BB Comdial 6414S-PG
Comdial 6600E-AB
Comdial 6614S-AB
Comdial 6614T-FB
Comdial 6620E-PG
Comdial 6600E-FB
Comdial 6614S-FB
Comdial 6614T-PG
Comdial 6600E-PG
Comdial 6614S-PG
Comdial 6620-PG
Comdial 6700S-PG Comdial 6706X-AS
Comdial 6706X-PG
Comdial 6714S-PG
Comdial 6714S-AS Comdial 6714S-FB
Comdial 6714X-FB Comdial 6714X-PG
Comdial DB32S-PG Comdial DB70-PG *Partial List
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 11 of 14
Feature Dialing Code Numbering Plan
All Call Page
Attendant Calling
Automatic Redialing
Background Music
Feature
Automatic Call Back
Station-to-Station
Messaging
LCD Messaging
Call Forwarding
Call Park
On
Off
Activate
Cancel
Activate
Cancel
Set
Cancel
Personal
Cancel
All Calls
Cancel
Park
Call Pickup
Call Waiting Tone
Do Not Disturb
Pickup
Directed
Group
Send
Cancel
Set
Cancel
Executive Override
Handsfree Answer
Block
Hold
Set
Cancel
Manual
Exclusive
Direct
Direct Hold Pickup
Trunk Answer from any Station
Trunk Group Access Group 1
Group 2
Group 3
Group 4
Meet Me Answer Paging
Message Waiting Set
Cancel from Idle
Cancel on line
Retrieve Message
Night Transfer (from On attendant station only) Off
Multiline Telephones
Command
ITCM 87
ITCM 0
Programmed Softkey
ITCM * 1
ITCM # 1
ITCM, Ext. *6
ITCM # 6
ITCM, Ext. *7
ITCM #7, Ext.
ITCM * 02 (1-0)
ITCM # 02
ITCM * 05, Ext.
ITCM # 05
ITCM *5, Ext.
ITCM # 5
ITCM * (91-99)
ITCM # (91-99)
ITCM * 4, Ext.
ITCM # 4
ITCM, Ext * 01
Hang up
Programmed Softkey
Programmed Softkey
ITCM, Ext, * 03
MUTE
MUTE
HOLD
HOLD, HOLD
ITCM * 90, Ext
ITCM # 90
ITCM 80
ITCM 9
ITCM 81
ITCM 82
ITCM 83
ITCM 88
ITCM * 3, Ext.
ITCM # 3, Ext.
ITCM
ITCM, HOLD
ITCM * # 03 (A1)
ITCM * # 03 (A1)
# (91-99)
*4, Ext.
#4
Ext., * 01
Hang up n/a n/a
Ext., * 03 n/a n/a
HOLD
HOLD, HOLD
* 90, Ext.
#90
80
9
81
82
83
Single Line Keysets
Command
87
0 n/a n/a n/a
Ext. * 6
#6
Ext, *7
* 7, Ext.
* 02 (1-0)
# 02
* 05, Ext.
# 05
*5, Ext.
# 5
HOLD, FLASH * (91-
99)
88
* 3, Ext.
# 3, Ext. n/a
HOLD n/a n/a
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 12 of 14
Feature
Personal Ringing Tones Set tones 1-4
Trunk Queuing Enable
Saved Number Redial
Cancel
Use
Speed Dial
Store
Station
System
Redial (Last number dialed)
Voice Announce Block On
Zone Page
Off
Zone 1
Zone 2
Zone 3
Multiline Telephones
Command
ITCM #* 4 (1-4)
Single Line Keysets
Command n/a
ITCM (Group code) * 8 Group code * 8
ITCM # 8 #8
HOLD, Programmed
Softkey n/a
Programmed Softkey
1-0 n/a
Trunk code, SHIFT, 1-
0
*01-99
#
ITCM * 2
ITCM # 2
ITCM 84
ITCM 85
ITCM 86
Trunk code, SHIFT, *
01-99
Trunk code, SHIFT, # n/a n/a
84
85
86
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 13 of 14
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
System Speed Dial Index
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
0
1
2
3
4
Personal Speed Dial Index
5
6
7
8
9
Courtesy of Main Resource, Inc.
Visit www.MainResource.com
for all your Comdial needs.
Page 14 of 14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement