Lynx L30WD Bbq And Gas Grill User manual
Add to my manuals
9 Pages
Lynx L30WD warming drawer offers precise temperature control, ranging from 60°F to 220°F, making it ideal for keeping food warm and moist until ready to serve. Its stainless steel construction ensures durability, while the adjustable moisture vent helps maintain the desired humidity level for various food types. Utilize the steam pans for moist cooking or to add moisture to the air, preventing food from drying out. Additionally, the warming drawer can be used to proof yeast dough, providing the perfect environment for the dough to rise.
advertisement
User Manual / Installation Instructions
Warming Drawer and Warming Drawer Cabinet
Warming Drawer Models
L30WD
L42CC
Lynx Professional Grills
6023 E. Bandini Blvd.
Commerce, CA 90040
Service: (888) 289-5969
Tel: (323) 838-1770
Fax: (323) 838-1782
As product improvement is an ongoing process at Lynx, we reserve the right to change specifications and design without notice.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: When using electrical appliances, basic safety precautions should always be followed including the following:
1. Read all instructions before using the warming drawer.
2. Do not touch hot surfaces. Use handles or knobs. Use only dry potholders. Moist or damp potholders may cause a steam burn.
3. To protect against electrical shock, do not immerse cord, plugs, or base in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.
6. Do not operate any appliance with damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized facility for examination, repair or adjustment.
7. The use of accessory attachment not recommended by the appliance manufacturer may cause injuries.
8. For indoor and outdoor use.
9. Do not let cord hang over edge of table or counter or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner or in a heated oven.
11. Extreme caution must be used when moving an appliance containing hot oil or other liquids.
12. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to “off”, then remove plug from wall outlet.
13. Do not use appliance for other than intended use.
14. Be sure that the warming drawer is installed and grounded properly by a qualified technician.
15. Keep the warming drawer away from water sprinklers.
16. Do not store any materials in the drawer, other than manufacturer’s recommended accessories, when not in use.
17. Flammable materials should not be stored in the drawer, at any time.
18. Always place steam racks in desired position while the appliance is cool.
19. Keep warming drawer vent ducts unobstructed.
20. Do not use plastic wrap to cover foods or plastic food containers in the drawer for heating. Plastics can melt inside the warming drawer.
21. Use care when opening the drawer. Let hot air or steam escape before removing or replacing food.
22. Do not touch the heating elements or interior surface of the drawer while it is in use.
23. Do not place food in unopened containers in the drawer. Pressure could build up and cause the container to burst.
24. Do not repair or replace any part of this drawer. All servicing should be done by an authorized service agency.
25. Save these instructions.
Page 1
ITEM
3
4
1
2
5
6
7
1 2
DESCRIPTION
WARMING DRAWER FEATURES
DIAGRAM AND PARTS LIST
HEATING ELEMENT
THERMOSTAT
HEAT ON LIGHT
CHROME BEZEL
CONTROL KNOB
ROLLER GUIDES
DRAWER HANDLE
4 3 5
ITEM
8
9
6
10
11
12
13
DESCRIPTION
HANDLE BRACKET
DRAWER
STEAM PAN GUIDE
STEAM PAN
STEAM RACK
STEAM PAN LID
13
12
11
10
9
8
7
MOISTURE VENT CONTROL
Page 2
WARMING DRAWER CABINET FEATURES
DIAGRAM AND PARTS LIST
6
7
4
5
8
Item Description
1 Heating Element
2
3
Thermostat
Heat On Light
Chrome Bezel
Control Knob
Roller Guides
Drawer Handle
Handle Bracket
Item
9
10
11
12
13
14
15
16
Description
Warming Drawer
Steam Pan Guide
Steam Pan
Steam Rack
Steam Pan Lid
Storage Drawer
Tank Drawer
Door Panel
Page 3
WARMING DRAWER INSTALLATION
Page 4
WARMING DRAWER CABINET INSTALLATION
Page 5
TEMPERATURE CONTROL
The temperature control dial is used to select the temperature of the warming drawer. It is located on the right hand side of the control panel and has dial settings from 1 to 10.
The #1 setting is the lowest temperature, which is around 60 o F, while the setting “10” is the highest temperature, which is around 220 o F.
The majority of foods are held between temperature settings of 5-6.
The warming drawer should only be opened when adding or removing food. Continuous opening of the drawer allows warm air to escape and make the food colder.
Do not use aluminum foil to line the drawer. It is an excellent heat insulator and will trap heat beneath it. This may affect the performance of the warming drawer and the interior finish.
HEAT-ON LIGHT
The heat-on light is located above the temperature control knob. The red light turns on when the control knob is set and cycles “on” and “off” with the heating element as temperature is maintained.
MOISTURE VENT CONTROL
The moisture vent control is located at the top inside of the warming drawer. It can be adjusted in any position between “open” and “close” to maintain desired degree of moisture. a) For crispy foods, slide the moisture vent control inward to open the vents and allows the moisture to escape. b) For moist food, side the moisture vent control outward to close the vents and seal the moisture inside the drawer
Page 6
HEATING INSTRUCTIONS
1. Dry Heat a) The main function of the warming drawer is to hold hot cooked foods at serving temperature. b) Place previously prepared foods directly into the empty steam pans (no water) and set the moisture vent control. c) For crispy foods, slide the moisture vent control inward to open the vents and allow the moisture to escape. d) Set the temperature control dial. Heat-on light will appear until the desired temperature is reached.
2. Moist Heat b) The warming drawer also seals moisture within the drawer to keep the food moist. c) Put just enough of water, approximately 1/2” high, in the steam pans. d) Place the steam rack inside the steam pan. e) Place the food directly on the rack or use a suitable container that will fit in the steam pans. Do not use plastic containers or utensils. f) Slide the moisture vent control outward to close the vents and seal the moisture inside the drawer. g) Set the temperature control dial. Heat-on light will appear until the desired temperature is reached. h) Periodically, check the water level in the steam pans and add water when necessary.
3. Proofing Yeast Dough a) Yeast dough can be proofed in a warming drawer. b) Place the dough in a bowl and turn the temperature control at the lowest setting, to facilitate the fermentation process. c) Place a towel over the dough to minimize surface drying. d) Let the dough remain in the warming drawer until it has doubled in size and a slight depression remains when the surface is touched gently with a finger.
CLEANING AND MAINTENANCE
The Warming Drawer is made of welded #304 stainless steel. It is non-rusting and nonmagnetic.
1. Allow the warming drawer and its accessories to cool before cleaning.
2. Remove steam pans and all accessories from warming drawer.
3. Clean all items including the drawer with the mildest cleanser. Scrub dirt with sponge.
4. When cleaning the front panel, always scrub in the direction of the grain. In order to maintain the luster and highlights of polished surface, do not use abrasives when cleaning polished surfaces. Use the mildest cleaner.
5. Do not use steel wool to clean the drawer and accessories.
6. Check out the slide rails and make sure they are clean and free from debris
7. It is highly recommended to clean the warming drawer after every use.
Page 7
TROUBLE SHOOTING GUIDE
PROBLEM
1. Warming drawer will not heat up.
2. Heat –on light does not come “on”.
WHAT TO DO
1. Check if the unit is plugged in to an electrical outlet.
2. Check if the temperature control dial is set properly.
3. Check if the circuit breaker is open.
If service is required: 1. Call your dealer, or authorized service agency.
2. Provide the following information: number purchased d. Name of dealer where the unit was purchased from
FOR YOUR RECORDS
Please record the following information and refer this information when contacting the company or an authorized service agent. This information is found on the data plate.
Model Number
Serial Number
Date of Purchase
Place of Purchase
Page 8
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement